Haier Washer Dryer HWM65 0566 User Manual

Fully Automatic Washing Machine  
User's manual  
This manual is for  
HWM65-0566  
Please read this manual carefully  
before using.  
Retain it for future reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing list  
Names of the parts  
Quantity  
Name  
One  
User's manual  
Water inlet valve  
Top lid component  
Control panel  
Component of the  
water inlet hose  
Water absorption  
cushion  
The end connecting to  
the washing machine  
One  
Filter cover  
Detergent box  
Handle  
Jointer connecting the  
water inlet hose and  
the water faucet  
Balance ring  
Power cord  
Back cover  
Drain hose  
Lint filter(two)  
Inner tub  
The end connecting to the  
water inlet hose jointer  
Pulsator  
Adjustable leg  
film  
One  
Adjustable leg  
Front control board  
Cabinet  
Bottom cover  
(Inside the inner tub of washing machine)  
Drain hose frame  
Fixed leg (3 pieces)  
Topping screws  
Eight  
One  
Full automatic washing machine  
Meaning and description of the symbols  
Warning sign  
Contents marked with that symbol are related to the  
safety of the product and the personal safety of the users.  
Please operate in strict conformity to the contents.  
Specification  
Contents marked with that symbol are actions forbidden  
to perform. Performing of those action may result in  
damage of the machine or influence the personal safety of  
the users.  
Forbidden sign  
Water level/Water  
quantity (about)  
1/12L 2/16L 3/20L 4/24L 5/28L  
6/32L 7/36L 8/40L 9/43L 10/46L  
Water Injection pressure  
0.03MPa 1.0MPa  
~
Rated washing /  
spinning capacity  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble-shooting Answer to question  
Safety precautions  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.  
Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department  
or after-sale service department of our company. Do not repair it by yourself.  
The washing machine must be positioned  
Please plug the power plug on special  
receptacle. Be sure to use three-pins  
power receptacle. Ensure that the earthing  
prong of the power receptacle is earthed  
reliably. Use leakage protector if possible.  
so that the plug is accessible. Be sure to pull the  
plug off and close the water faucet in  
following cases: power failure, delivering  
the machine, setting the machine idle or  
c l e a n i n g t h e m a c h i n e . D o n o t p l u g  
or pull the power plug with wet hand.  
Phenomena  
The reason  
How to settle  
The digitron displays E0.  
The top lid is opened during reserve procedure.  
Close the top lid.  
Put down the drain hose. Open and close the  
top lid once.  
Clean the foreign material. Open and close the  
top lid once.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose put down?  
Is the drain hose blocked?  
It stops running in midway. The digitron  
displays E2.  
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.  
Keep the pin of the power plug clean, if the power plug is polluted with dust,  
please wipe with dry cloth carefully.  
If the power cord or the power plug is bad, to avoid risk it is  
required to have it replaced by the technicians of our  
special shop or the after-sale service department.  
The top lid is not closed.  
Close the top lid.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Reorder the laundries. Close the top lid.  
Th machine will start running after 10  
seconds of being placed horizontally.  
Are the laundries put slantingly?  
Is the machine slanting?  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
Open the water tap. Push the start/Pause  
button once.  
Clean the water inlet valve then push  
the start/Pause button once.  
Push the Start/Pause button once.  
The water filling does not work, or is  
slow. After about 30 minutes later,  
the digital displays E4.  
In case the washing machine is installed on ground  
with carpet, do not block the ventilation hole with  
carpet.  
Do not use water hotter than 50  
.
Please contact the after-sales  
service department.  
The digitron displays E6.  
The water level sensor is bad.  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
The ventilation  
holes at the bottom  
Not wash  
The machine does  
not act  
Back  
Soft object  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Front  
Not spin  
Adjust the machine to be even  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
There's abnormal sound  
inside the machine  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Do not put the machine at damp place like  
the bathroom. Never wash it with water. Do  
not put wet laundries on the control panel.  
Is the screw of the jointer of water  
inlet hose loose or awry?  
Fasten the screw of the jointer properly.  
The water tap leaks  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
The wash procedure is paused.  
The cloth sensor is checking the cloth, it will add water after 48 seconds.  
The program is setting the drain time. Some time is needed  
before it starts spinning.  
Push the PROGRAM button to select SPIN,  
but it doesn't work.  
Do not let the machine share one receptacle with other  
electric appliances. If the plugging into the receptacle  
is loose, do not use the plug any more.  
The pulsator pauses during water inlet  
in wash and rinse.  
It is to avoid splashing during water inlet.  
There may be some water flowing out of the  
drain hose in the first use of the machine.  
It is the water remained in the factory inspection of performance.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disposal after washing  
Safety precautions  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Do not put hand into the rotating tub. It is dangerous  
Do not decompose, repair or alter the machine by  
yourself.  
even if the rotation speed is slow. Take special care of  
the children. Keep children away from the washing  
machine to avoid them climbing on.  
The lint filter must be used during washing.  
Clean the detergent box and set it on  
It must be cleaned in time after each using.  
the control panel seat.  
Lint filter:  
1.The method of dismantle: Push it up aslant and gently.  
1.Push down the spring piece of the top lint filter  
to make the claws out of the filter cover, and then  
pull out the lint filter to get it down. figure1  
2.Pull the back of the lint filter, and then you can  
get down it off the front cover of the lint filter. figure2  
3.Sweep the rubbish in the lint filter.  
2.The method of install : install it upwards and aslant  
and push it in .  
Do not wash laundries with volatile materials  
(such as thinner, petrol etc.).  
Do not put any hot or heavy items (such as the  
kettle with hot water) on the washing machine.  
4.Put the back of the lint filter into the front cover .  
5.Put the lint filter into filter cover, and make it  
tight .  
trol  
Pe  
Benzene  
6.Make sure the lint filter well installed, or it can  
influence your use.  
Up  
The back cover of lint filter  
Up  
Install  
Dismantle  
Dismantle  
Install  
Dismantle  
Install  
Down  
The front cover of lint filter  
Figure 2  
The handicapped or children without care shall not use  
the machine.  
Down  
Keep the machine away from direct sunlight and  
heat source like the heater.  
Figure 1  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
Wipe it with neutral detergent.  
Please clean it with brush every two months.  
Do not wipe it with thinner, petrol, alcohol etc.  
Benzene  
Please keep the lint filter in good condition,  
and install it to proper position during  
washing. If the lint filter is lost or  
To protect your laundries and washing machine,  
please take out all of the coins, buttons, sand, hairpin  
and other foreign materials before washing.  
Install  
Dismantle  
damaged, please contact the customer  
care agent of our company.  
.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
To change the direction of drain pipe, please contact the customer care agent of our company.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,  
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use  
otherwise the washing effects may be lowered or the washer may be damaged.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
Attention  
.
Even there's no water in the tub, a certain period is  
required before spin starting.  
Do not use the soak program for the woolen textiles.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
Install the bottom plate  
Back  
After you open the package, please lean  
the washing machine gently down on soft  
items ( like the towel cloth, blanket, etc. ).  
Install the bottom plate to the bottom of  
The pulsator will not rotate unless the water is  
filled to"24L"water level.  
Front  
the machine, then lift the machine up  
gently. See to the figure:  
The soak procedure can work in cooperation with automatic programs like standard,normal, jeans, and fiber .  
There is intermittent pulsator stirring during soak.  
Screw  
After the machine starts operation, you can only set the program and procedure during washing,soak and can not  
make setting in other cases.  
Soft items  
Bottom plate  
Water level  
4 Push the " water level" button, select suitable water level  
Adjust the Installation position  
After switching on the power and the "standard"or" normal"programs set,washing machine will execute fuzzy  
program automatically to detect the cloth.After defection, it can set the water level automatically. To select other  
water level, first push the "start/pause" button, then push the "water level" button to  
set the water level.  
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground  
will result in unstable running or stoppage of the machine. Please adjust it with following methods:  
Confirm it's horizontal:  
Hang the lead line to check if it is  
horizontal.  
5 Push the "reserve" button to select suitable reserve wash program  
Adjust the adjustable leg:  
1 .To twist the adjustable leg, please first lift up the  
side of the leg slightly, loosen the adjustable nut,  
and twist the leg.  
After switching on the power, the reserve program is set to off mode automatically. If you need to  
set the washing procedure to be finished at reserved time, please push the " reserve " button to  
set the reserve wash program. Refer to reserve button in Page 10 for selection.  
the adjustable nut  
Fasten  
Loosen  
2 . After adjustment, fasten the nut.  
the adjustable feet  
High  
Low  
Confirm the operation of reserve program  
To change the running program or cancel the reserve setting, you  
need to switch off the power and make new selection.  
6 Push the "Start/Pause" button  
6 Finish washing  
5 Close the top lid  
As the top lid opened, the washer will automatically  
given alarm and stop running, exclusively during  
draining  
After finishing wash it'll  
alarm automatically  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to change the direction of the drain hose  
Steps of using the operation buttons and  
description of the steps  
b
1.Dismantle the rear cover of the washing machine.  
3.Dismantle the drain outlet protecting cover at the other side,  
(the way is the same as the drain bushing),then install the drain  
bushing, as indicated in Figure 4.  
2.Put down the drain hose Take off the drain hose  
frame as indicated in Figure 1.Take the drain hose into  
the cabinet then nip the drain fixing clamp to make  
it deviated from the clip the other hand is used to put  
down the drain bushing as indicated in Figure 2 3.  
46  
Standard  
Fibre  
43  
36  
28  
20  
12  
Tub dry  
Normal  
Quick  
20  
15  
40  
32  
24  
16  
Woollen Jean  
4.Extend the drain hose from the other side. Fix the drain hose  
with drain hose frame onto the cabinet, as indicated in Figure 5.  
drain outlet protecting  
cover  
Reserve  
Spin  
6
Drain hose  
Figure 5  
Figure 4  
5
Drain hose support  
Cabinet  
Inner  
Drain bushing  
Figure 2  
Drain bushing  
Figure 1  
5.Install the drain outlet protecting cover to the other side,  
as indicated in Figure 6  
Outer  
Push  
Drain bushing  
1.Push "power" button to switch on the power  
Take do  
wn  
Drain hose fixing  
clamp  
Figure 6  
Push  
Figure 3  
2.Push "program" button to select suitable  
full-auto program  
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose  
with our company serviceman .  
After the power is switched on, "normal"is automatically set. To select other full-auto program, please  
push the "program" button till the corresponding indicator is on. Refer to the "Program button" on Page 11.  
E.g. Set to "Quick wash" program for small quantity of laundries with light soil.  
Usage the drain hose  
The drainage shall be smooth with the drain hose.  
1.The height of the drain hose shall be less than 10cm,  
or the drainage will not be smooth, and cost such long  
time that the machine may stop at mid way.  
4.If extra drain hose is needed, please make separate  
purchase. The inner diameter of the extra hose shall  
not less than 30mm, and the length shall not exceed  
1.5m.  
2.Do not step on or press the drain hose.  
In selecting the NORMAL or standard program, the machine will execute fuzzy program to select  
water and wash time according to the cloth and weight of the laundries. The full procedure is controlled  
automatically.  
Push the "SOAK", "WASH", "RINSE" OR "SPIN" button to select suitable procedure.  
3. If the drain hose is too long, cut it at mid point. To make  
smooth drainage, cut the front end of the hose slantingly.  
5.If the extra hose is too long, cut it either at A or at B.  
Spin  
5
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install the water inlet hose  
Confirm the water faucet  
Reserve, remain time digitron  
"Power" button  
Water faucet,suitable  
Water faucet,not suitable  
It displays "--" during detecting.  
Push the "power" button to switch on the power.  
Under power-on mode, push it to switch off the power.  
Push the "power" button to switch on the power. If  
the "start/pause" button is not pushed, the machine  
will switch off the power automatically after 5 minutes.  
It displays remained reserve time (hour).  
It displays total remained time (min).  
It displays abnormal symbol in abnormal situation.  
(See to Page15)  
Outlet end surface  
>10mm  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
46  
Standard  
43  
36  
28  
20  
12  
Tub dry  
Normal  
Quick  
TUB DRY button  
40  
32  
24  
16  
Fibre  
Connection between the water inlet hose jointer and the water faucet  
Push the"TUB DRY"button,the indicator  
is lighted,and the"TUB DRY"function is  
operating. After washing,the innerand  
outer tub is wet,mildew may grow not  
using for a long time.Then,the  
Woollen Jean  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,  
otherwise it may leak water. See to Figure 3.)  
"TUB DRY" fuction can make the tub dry  
preventing mildew from  
growing.  
Notice: When "Tub Dry" have been selected,  
eserve  
Res  
ve  
all functions are unavailable except " Reserve" ,  
the indicators of Spin, Tub Dry and Reserve  
LED are lighted, and others are off.  
water inlet hose jointer  
Screw  
Slider  
Sign plate  
Screw knife  
Bushing  
Lock level  
water inlet hose  
Figure 1  
Figure 2  
Figure 3  
selection button  
PROGRAM  
WATE  
R LEV  
EL  
The washing machine can detect the laundries automatically.  
After detection, it will set the water level to suitable value among  
24L,32L,40L,46L automatically.  
You can also set water level by yourself. After the machine is started, it  
will not set water level automatically. You shall push the start/pause  
button to make new setting.  
If there's water inside the tub, the machine cannot detect the laundries  
and will display water level 32L .  
If wet laundries are put in, it may display water level 46L . You must set  
suitable water level by yourself.  
If QUICK programs selected, it will display water level 20L .  
When water level 16L is reached in water filling, it will perform  
washing while filling water. When water level 20L is reached, it will  
change to normal washing.  
If WOOLLEN program selected,water level only can be set between  
32L and 46L.  
During operation of wash,soak and rinse program, you can push  
down the water level button to add water. When you release the button,  
or it reaches the overflow water level, the machine will stop adding  
water.  
but  
ton  
3.Fasten the four screws evenly. See to Figure 4.  
Following automatic programs are available for selection  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
Applicable situation  
Common washing  
PROGRAM  
STANDARD  
QUICK  
"Reserve" button  
Quick and high-efficiency wash for common  
laundries  
remark: Before installation, the threading is 4mmabove the upper surface of the nut.  
The digitron displays remain time  
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.  
Washing the relatively big and thick laundries  
Washing the chemical fiber laundries  
Washing the woolen textiles  
before washing is finished (in minutes)  
Push "reserve" button, the digitron  
displays the reserve time of washing  
(in hours). The indicator flashes to  
indicate that the reserve function  
is operating.Push "reserve" button to  
display the reserve mode.  
JEAN  
FIBER  
About 4mm before twisting  
About less than 2mm after twisting  
WOOLLEN  
NORMAL  
Common washing  
Screw nut  
Figure 6  
Figure 4  
Figure 5  
The water level decided may be different from actual value because of  
the different moisture level of the laundries.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4 Use the operation buttons  
Connection between the water inlet hose and the washer  
Description of the function of buttons  
a
CHILD LOCK FUNCTION  
1.Do not take off the water absorption cushion. Please check if the  
nut of the water  
cushion is dropped or damaged before each usage. If it happens  
inlet hose  
Push and hold the WATER LEVEL button and SPIN button,  
then push down the POWER ON/OFF button. The digitron  
displays CL . After setting, push downthe START/PAUSE button.  
The child lock function isactivated. All of the buttons are locked  
and cannot make selection.  
Release the child lock function: push down the RESERVE and  
SPIN button at the same time for more than 2 seconds. After a beep  
sound, the child lock function is released.  
Indicator mode and meaning  
please contact our after-sale department immediately.  
2 Put the nut of the water inlet hose on the valve jointer.  
3 Fasten the nut. Swing it gently to confirm if it's suitable.  
Flashing, indicating the running program  
On, indicating the program about to run or the selection mode  
jointer of the  
water inlet valve  
water absorption  
cushion.  
"Start/pause" button  
After the poweris switched on, press it to  
start the machine  
Connection between the jointer of the water inlet hose and the water inlet hose  
During working, pushit to pause.  
During pause, pushthis button torestart  
and go onworking  
Spin  
Soak  
Wash  
Rinse  
30  
the jointer of the  
water inlet hose  
1.Push down the slider. Insert the water inlet hose into the jointer.  
Slider  
Locking level  
Over flow  
2 Hang the lock lever to the jointer. Release the slider till a click  
sound is heard.  
Wash  
Spin  
Check the connection between the jointer of the water inlet hose  
and the water faucet  
1.Swing the hose gently to confirm if it is fastened stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
WASH button  
SOAK button  
RINSE button  
SPIN button  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
Push the WASH button to set  
the wash procedure.  
Push the SOAK button to set  
the soak procedure.  
Push the RINSE button to set the rinse  
and procedure.  
Push the SPIN button to set  
the spin procedure.  
During STANDARD  
During STANDARD NORMAL  
and JEAN programs, push the  
SOAK button to set different  
soak time (10,20,30 minutes)  
During STANDARD NORMAL and  
JEAN programs, push the RINSE  
button to set different rinse times ( 0, 1,  
2, 3, 4times).  
During STANDARD NORMAL  
and JEAN programs, push  
the SPIN button to set different  
spin time(1,3,5,7minutes)  
During FIBER program, push  
the SPIN button to select spin  
procedure, but the spin time  
cannot change.  
NORMAL and JEAN  
programs, push the wash  
button to set different wash time  
(6,9,12,15 minutes)  
During FIBER  
program,  
While the "Overflow" digitron is  
lighting,the program of the overflow  
rinse has been selected.  
During FIBER program, push  
the WASH button to select  
wash procedure, but the wash  
time cannot change.  
push the soak button to select  
soak procedure, but the soak  
time cannot change.  
Dismantle the water inlet hose  
During FIBER programs, push the  
RINSE button to select rinse procedure,  
but the rinse times cannot change.  
During QUICK and WOOLLEN  
programs, push the SOAK  
button, the machine have no  
reaction.  
1. Close the water faucet.  
During QUICK  
,
WOOLLEN  
,
During QUICK WOOLLEN  
Programs, push the wash  
button the machine have no  
reaction.  
programs, push the SPIN  
button, the machine have no  
reaction.  
2. Press the locking lever. Push down the slider. Then pull of the water inlet  
hose.  
During QUICK  
,
WOOLLEN programs,  
push the RINSE button, the machine  
have no reaction.  
Locking level  
If the machine is used frequently, the jointer of the water inlet hose can be  
kept on the faucet to prevent damaging the fixing screw.  
Slider  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Preparation before washing  
2.Put in the laundries  
The capacity of washing of the machine refer to the largest weight of the  
standard laundries under dry condition that can be washed in one  
time. Laundries quantity in one washing cycle shall be lower than  
the rated capacity. The largest capacity of this machine is 9.0 kg.  
Preparation before washing  
1.Connect the water inlet hose  
2.Confirm that the washing machine is earthed  
reliably. Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose  
The thickness ,size , type of the cloth will influence the actual washing capacity.  
It is suitable to put in reasonable amount of laundries and the laundries can be  
turned round in washing for one time washing.  
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid  
splashing of water.  
3. Usage of the detergent  
Control panel seat  
Add washing powder and softener into  
the box directly as per indicated in left figure  
Liquid detergent  
inlet  
4.slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally  
After adding, close the box.  
Liquid whitener inlet  
Softener inlet  
Washing powder inlet  
Washing powder box  
Pay attention to followings before washing the laundries  
The quantity of the  
laundries shall not  
exceed the rated  
value. The big  
laundries like the  
jeans shall be put  
in loosely.  
When the pulsator is  
running ,the buttons of  
the laundries may cause  
noise. For the sake of  
discretion ,please put  
the laundries with  
buttons into other  
Confirm if there's  
special requirement  
for the laundries.  
Clear the pocket.  
Take out the coins ,  
sand, hairpins etc.  
Fasten the buttons  
and zippers.  
How to use washing powder  
How to use softener  
See to the manual of softener for the usage and dosage.  
When adding softener into the softener inlet of washing  
powder box, note that it shall not exceed the lower side  
of the cap.  
Do not leave the softener for long period after adding it  
into the box. Otherwise it may be solidified and block the inlet.  
As the softener is easy to solidify, please clean the box  
frequently.(You shall clean it each time you use reserve  
function).  
It is suggested to add washing powder into the box  
directly under fuzzy program and reserve program.  
Dissolve directly inside the washing machine: (not  
applicable for fuzzy and reserve program)  
1.Add some water  
laundries.  
2.Add washing powder. Run for about 30s to fully dissolve  
Powder. Then push the"start/pause" button.  
the  
3.Put in laundries. Select suitable water level. Push the  
Button again.  
"start/pause"  
Before use softener, you must select to sterilize function  
Quick dissolving of washing powder:  
1. Prepare warm water of 30 C and container.  
2. Add washing powder while stirring to dissolve it  
completely.  
How to use whitener  
Please add suitable washing powder as per the laundries  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,  
please apply detergent in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.  
f. Do not put those laundries polluted by chemicals directly into the washing machine.  
g.For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into  
mesh bag for washing.  
quantity, the set water level and water quantity.  
Add water to stipulated level. Dilute the whitener with container,  
and then pour it into the liquid whitener inlet slowly.  
If you select quick wash program, it is suggested to use  
liquid detergent instead of washing powder to guarantee  
Laundries with color or pattern is not colorfast, thus not applicable.  
the washing effect.  
It is not recommended to use rich-foam washing powder.  
The whitener shall not touch laundries directly.  
See to the manual of whitener for the usage and dosage.  
For whitener in powder, dissolve it before use.  
Washing powder with poor quality or long-time storage may  
get caked. Please clean the detergent box duly in usage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Camping Equipment 334644A User Manual
Harbor Freight Tools Scale 98059 User Manual
Health O Meter Scale 400KL User Manual
Hearth and Home Technologies Indoor Fireplace SMARTBATT HNG User Manual
Heatcraft Refrigeration Products Power Supply 25000601 User Manual
HP Hewlett Packard Computer Monitor D2828A User Manual
Husqvarna Lawn Mower YTH26V54 User Manual
Hypertec Mouse HKB260UBKLC User Manual
IBM Computer Monitor C220p User Manual
ICP DAS USA Network Card LinCon 8000 User Manual