Haier Washer Dryer HWM50 10 User Manual

User's manual  
Full Automatic Washing Machine  
This manual is for  
HWM50-10  
HWM50-10B  
Please read this manual  
carefully before using.  
Retain it for future reference.  
0030805169G  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Names of the parts  
Top lidA  
Water valve  
Water absorption  
cushion  
Top lid B  
Lint filter  
Notice label  
(Installed by user)  
Detergent box  
Control panel  
Filter cover  
Inner tub  
Hanging hole  
for the drain  
hose  
Handle  
Pulsator  
Adjustable foot  
stick  
Control panel  
film  
Drain hose  
ack cover  
Cabinet  
Fixed foot (3)  
Adjustable foot  
Meaning and description of the symbols  
Contents marked with that symbol are related to the safety  
of the product and the personal safety of the users. Please  
operate in strict conformity to the contents, otherwise it may  
cause damage of the machine or injure the personal safety  
of the user.  
Warning sign  
Contents marked with that symbol are actions forbidden to  
perform. Performing of those actions may result in damage  
of the machine or injure the personal safety of the user.  
Forbidden sign  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety precautions  
The power cord plug should be convenient  
Please plug the plug on special receptacle  
with rated voltage. Be sure to use single-  
phase three pins receptacle. Ensure the  
earthing prong of the power receptacle is  
earthed reliably. Use leakage protector if  
possible.  
to be pluged in or pluged out with hand  
while the washing machine runs normally.  
Be sure to pull the plug out and close the  
water tap when the machine is idle, when  
moving the machine, or when cleaning  
the machine. Do not use wet hand to insert  
or pull out the power plug.  
Do not damage the power cord, bend ,extend, twist, bind or alter it by force. Do not press or  
nip it with weight. If the power cord or the power plug is bad, or the power plug becomes  
flexible, to avoid risk it is required to have it replaced by  
the technicians of our special shop or the after-sale  
service department. Keep the pin of the power plug  
clean, if the power plug is polluted with dust, please  
wipe with dry cloth carefully.  
Do not use water hotter above 50 C .  
Do not put the machine at damp place like  
the bathroom. Never wash it with water.  
Not put wet laundries on the control panel.  
In case the washing machine is installed  
on ground with carpet, do not block the  
ventilation hole with carpet.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
The ventilation holes  
at the bottom  
soft items  
Do not let the machine share one receptacle with other  
electric appliances. If the power plug is damaged, or  
the plugging into the receptacle is loose,  
do not use the plug any more.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety precautions  
Do not stretch hands into the working  
Do not decompose, repair or alter the  
machine by yourself.  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children. Do not let the children  
climb the washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.)  
Do not put any hot or heavy items (such  
as the kettle with hot water ) on the  
washing machine.  
r
Petrol  
nne  
Thi  
The handicapped or children without  
care shall not use the machine.  
Keep the machine away from direct  
sunlight and heat source like the heater.  
To prevent the lint inside the tub from blocking  
the cascade outlet during washing, please  
keep the lint filter in good condition, and  
Toprotect your laundries and wash-  
ing machine, please take out all of the  
coins, buttons, sand, hairpin and  
other foreign materials before washing.  
install it to proper position. If the lint filter  
is lost or damaged, please contact the local  
after-sales service department of our company.  
Please check if the water faucet is open,  
and if the connection of the water inlet  
pipe is proper.  
It is suggested to use foamless washing  
powder.  
Install  
Dismantle  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual. It is  
very important to your security and correct operating the machine.  
Install the lint filter  
Install the bottom plate  
After you open the package, please lean  
the washing machine gently down on soft  
items ( like the towel cloth, blanket, etc. ).  
Install the bottom plate to the bottom of the  
machine with the seven screws by a cross  
screwdriver, then lift the machine up gently.  
See to the figure:  
Push the lint filter downward to  
location for lint filter.  
Back  
Front  
Screw  
Bottom plate  
Soft items  
Adjust the installation position  
The largest allowed slope of the  
shank base of the machine is 2  
.
The slanting or rough ground will  
result in unstable running or  
stoppage of the machine. Please  
adjust it with following methods:  
Adjust the adjustable foot:  
1.To twist the adjustable foot, please  
first lift up the side of the foot slightly,  
loosen the adjustable nut, and twist  
the foot.  
adjustable nut  
Fasten  
adjustable foot  
Loosen  
High  
Low  
2.Fasten the nut after adjustment.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to change the direction of the drain hose  
1.Dismantle the back cover of the washing  
machine.  
3.Dismantle the protecting cover of the  
drain outlet at the other side (method  
the same as the bushing). Install the  
bushing as per indicated in Figure 4.  
2.Put down the drain hose. Take off the  
drain hose frame. As indicated in Figure  
1, put the drain hose into the cabinet.  
Then stretch one hand into the cabinet  
to nip the claw of the drain hose bush-  
ing to remove the claw from original  
position. Take off the drain hose bush-  
ing with the other hand. (As indicated in  
Figure 2 and 3).  
4.Extend the drain hose from the other  
side. Fix the drain hose onto the base  
frame with the drain hose frame. (As  
indicated in Figure 5)  
Drain outlet  
protecting cover  
Outer  
drain  
hose  
Drain hose bushing  
Figure 5  
Drain hose bushing  
Drain hose frame  
Figure 2  
Figure 4  
Figure 1  
Cabinet  
5.Install the protecting cover of the drain  
outlet at the other side as per indicated  
in Figure 6.  
Inner Outer  
Press  
Drain hose  
bushing  
Take off  
Drain hose  
bushing claw  
Figure 3  
Press  
Figure 6  
Usage of the drain hose  
The drain hoseshall drain smoothly  
1.The height of the drain hose shall be  
less than 10cm, or the drainage will not  
be smooth, and cost such long time that  
the machine may stop at mid way.  
4.If extra drain hose is needed, please  
make separate purchase. The inner  
diameter of the extra hose shall not  
less than 30mm, and the length shall  
not exceed 1.5m.  
2.Do not trample or press the drain hose.  
If the drain hose is too long, cut it at mid  
point. To make smooth drainage, cut the  
front end of the hose slantingly.  
5.If the extrahose is toolong, cut it  
either atA or at B point.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install the water inlet hose  
Confirm the water tap  
Water tap,not suitable  
Water tap,suitable  
Outlet end surface  
>10mm  
It is required that the front end shall be longer than 10mm.  
The outlet end surface of the tap shall be flat and smooth. If not please file it to  
avoid leakage.  
Connection between the water inlet hose jointer and  
the water tap  
1.Press the lower end of the lock lever and push down the slider. Take off the water  
inlet hose jointer from the water inlet hose component. See to Figure 1.  
2.Loosen the screw till the water tap can be accessed. Put the jointer of the water  
inlet hose on the tap. See to Figure 2. (If the tap diameter is too large and the jointer  
can not be set on the water tap, please loosen the four screws and take out the  
bushing in the jointer. See to the figure3.)  
Water inlet pipe jointer  
Screw  
Slider  
Mark label  
Screwdriver  
bushing  
Locking lever  
Water inlet pipe  
Figure 1  
Figure 2  
Figure 3  
3.Fasten the four screws evenly. See to Figure 4.  
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure.  
See to Figure 5.  
Remarks: Before twisting the fastening nut, the thread is 4mm above the  
upper surface of the nut. After twisting the fastening nut, the thread is 2mm  
above the upper surface of the nut. See to Figure 6.  
About 4mm before twisting  
About below 2mm after twisting  
Nut  
Figure 4  
Figure 5  
Figure 6  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connection between the water inlet hose and the  
washing machine  
1.Do not takeoff the water absorption  
cushion. Please checkif the cushion  
is dropped ordamaged before each  
usage. If ithappens please contact  
our after-sale departmentimmediately.  
2.Put the nutof the waterinlet hose on  
the valve jointer.  
Nut of the water inlet hose  
3.Fasten the nut. Swaying it gentlyto  
confirm if it'ssuitable.  
Water absorption cushion  
Jointer of thewater inlet valve  
Connection between the jointer of the water inlet  
hose and the water inlet hose  
1.Push down theslider. Insertthe  
water inlet hoseinto the jointer.  
Jointer of thewater  
inlet hose  
Slider  
Locking lever  
2.Hang the locklever to thejointer.  
Release the slidertill a click  
sound is heard.  
Check the connection between the jointer of the  
water inlet hose and the water tap  
1.Swaying the hosegently to confirmif it isfastened stable.  
2.After installation, openthe tap tocheck if itleaks.  
3.Do not bendthe hose withoverstrain.  
4.Before each usageplease check if  
the connection betweenthe jointer  
of the waterinlet hose andthe water  
tap, and theinstallation of the  
water inlet hoseare firm, soas to  
prevent dropping fromimproper  
Installation position.  
Take down the water inlet hose  
1.Close the watertap.  
2.Press the lockinglever. Pushdown the slider. Then  
pull off the water inlethose. If themachine is used  
more than onceevery week, thejointer of thewater  
inlet hose canbe kept onthe tap toprevent  
damaging the fixingscrew.  
Locking lever  
Slider  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose and open the  
water tap .  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth ter-  
minal to the gas pipe and tap water pipe.  
3.Put down the drain hose.  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Pay attention to followings before washing the laundries  
Confirm  
if  
Clear the pocket. Fasten the The quantity of  
When the pulsator  
the laundries is running , the  
shall not exceed buttons of the  
the rated value. laundries may  
The big laundries cause noise. For  
there's special Take out the  
requirement for coins , sand,  
the laundries. hairpins etc.  
buttons and  
zippers.  
like the jeans  
shall be put in  
loosely.  
t h e s a k e o f  
discretion, please  
put the laundries  
with buttons into  
other laundries.  
a. Please check if the laundries are applicable for washing.  
b. Separate those not colorfast from other laundries.  
c. For laundries not water absorbing, please put them into water with hands.  
d. For laundries with much soil, please remove the soil first. You can add detergent on the  
part with serious soil directly. It is much easier to remove the soil by that mean.  
e. For laundries likely to get lint ball or with long fiber, please first turn the inside out before  
putting them into the water.  
f. Do not put the laundries polluted with chemicals directly into the washing machine.  
For those small laundries ,laundries likely to be twisted or worn, and woolen laundries,  
please put them into mesh bag before washing.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Put in the laundries  
The capacity of washing andspinning of the  
machine refer to the largestweight of the  
standard laundries under dry condition that  
can be washedor spinned inone time. One  
time washing quantity shall be lower thanthe  
rated capacity.  
The thickness, size, type ofthe cloth willinf-  
luence the actual washing capacity. It is sui-  
table for onetime washing to put inreasona-  
ble amount oflaundries and the laundries can  
be turned round in washing.  
To wash thin laundries like thestocking, silk  
etc , pleasefirst put theminto washing mesh  
bag (which canbe purchased separately)  
before wash.  
Usage of the detergent  
How to use the washing  
powder  
Direct dissolved in the machine  
1.Fill water to "Low" water level.  
2.Add the power. Run for 30 seconds  
to dissolve it completely.  
Inlet box of the detergent  
3.Put in thelaundries. Select  
suitable water level.  
How to usethe whitener  
The instant dissolving of the washing  
powder:  
1.Prepare warm water of 30 and a  
container.  
2.Add the powderwhile stirring to  
fully dissolve it.  
Put in the proper quantities detergent  
according to the water level and the  
laundries quantities .  
It is suggested not to use high  
sudsing detergent.  
Washing powder with poor qualityor  
long time storage maybe caked.  
Please pay attention to cleaning the  
detergent box in time.  
Fill water to decided level. Dilute  
the whitener with container. Pour  
it slowly into the washing tub.  
Avoid using whitener on  
laundries with color or pattern as  
they are prone to lose color.  
The whitener shall not touch the  
laundries directly.  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
For powder whitener, please  
dissolve it before use.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use the operation buttons  
a.  
Description of the function of the buttons  
SURPLUS(MIN)  
"POWER ON/OFF"button  
To indicate remaining min. During  
program running.  
Press "Power On/Off"button to connect  
power supply.  
After power is connected, pressing this  
button will cut off the supply.  
To indicate remaining reserved  
time (hrs) during reservation period.  
To indicate fault symbols for abnormal  
conditions (see page 15)  
"START/PAUSE"button  
Page 15  
After the power is switched on, press it to  
start the machine  
During working, push it to pause working.  
During pause, push this button to restart  
and continue operation.  
PROGRAM STATUS  
PROCEDURE STATUS  
STANDARD  
JEANS  
SOAK  
WASH  
RINSE  
SPIN  
GENTLE  
QUICK WASH  
WASH  
SPIN  
POWER  
ON/OFF  
START  
PAUSE  
PROGRAM  
RESERVATION  
WATER LEVEL  
utton  
" b  
RESERVATION  
ROGRAM/  
"P  
Press"PROGRAM/RESERVATION " button  
you can select one or several programs of  
Standard, Jeans, Gentle, Quick Wash, Wash  
" WATER LEVEL"button  
and Spin.  
Press"PROGRAM/RESERVATION " button  
The user selects a suitable water level  
depending on the load.  
over 2 seconds, you can select the program  
of reservation. The nixie tube displays the  
reserved hours to the wash cycle end. Then  
pressth e  
"START/PAUSE "button the  
indicator flashes to indicate in-reservation.  
Remarks: 1. After pressing "POWER ON/OFF" to connect power supply, if the washing  
machine lasts idle more than 5 min, it would automatically shut off the supply.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b.  
Operating procedure and explanations for the  
buttons  
PROGRAM STATUS  
PROCEDURE STATUS  
STANDARD  
JEANS  
SOAK  
WASH  
RINSE  
SPIN  
GENTLE  
QUICK WASH  
WASH  
SPIN  
POWER  
ON/OFF  
START  
PAUSE  
PROGRAM  
RESERVATION  
WATER LEVEL  
1 Press the "POWER ON/OFF" button to switch on  
the power supply  
POWER  
ON/OFF  
2 Press the button of" PROGRAM/RESERVATION" to  
select a suitable full-automatic program  
PROGRAM  
RESERVATION  
After switching on, the "Standard" program will be thedefault. If other full-automatic program is  
desired, you can press thebutton "PROGRAM/RESERVATION" to getthe corresponding  
indicator on. Refer to the"Button of "PROGRAM/RESERVATION"  
paragraph on page 10.  
Page 10  
Example: Use the "Quick" program for slightly soiled articles.  
If there is water inside the tub, the machine cannot detect the laundries and will display  
middle level. If wet laundries are put in, it may display high level. You must set suitable  
water level by yourself.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attention  
Even there's no water in the tub, the  
spinning will start after a certain period.  
Do not use soak process for woolen  
laundries.  
Wash the laundries that are prone to lose  
colors separately from other laundries.  
The pulsator will not rotate unless the  
water is filled to selected water level.  
Selection method of the procedure programs  
Times of pushing  
the"select"button  
Contents(tthe nixie tube indicates  
the programs about to run)  
Selected program  
Applicable procedure  
0
1
2
3
4
5
Normal wash  
STANDARD  
JEANS  
Wash (bb) Rinse(cc) Spin(dd)  
Large, thick or heavily soiled  
laundry  
Soak (AA) Wash (bb)  
Rinse (CC) Spin (dd)  
The laundry needn'tspin to  
avoid wrinkles  
GENTLE  
Wash (bb) Rinse(cc) Spin(dd)  
Wash (bb) Rinse(cc) Spin(dd)  
Wash (bb)  
QUICK WASH  
For load below 1 kg  
Repeat using thewashing  
liquid  
WASH  
SPIN  
When the laundriesneed only  
spinning after manual  
washing (first drainthen spin)  
Spin(dd)  
If you push the " PROGRAM/RESERVATION" button for 6 times, it will  
resume the original mode, and it will circulate like that.  
If you select the"QUICK WASH" program, you have to set the full procedure  
of wash, rinse and spin. The procedure can not be selected.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 Press the "WATER LEVEL" button to select suitable  
water level  
WATER LEVEL  
After switching on the power, press the button "WATER LEVEL" to select a water level according  
to the load. Please refer to the button " Water level" on page 10.  
Page 10  
4 Push the " PROGRAM/RESERVATION" button  
to select suitable reserve program  
PROGRAM  
RESERVATION  
After switching on, the washing machinereserved wash programwill be automaticallyset  
inactive. If youdesire a washcycle to endat a reservedtime, you canpress the  
"PROGRAM/RESERVATION"button over 2 seconds to set a reserved wash program.  
Refer to The button of "PROGRAM/RESERVATION" on page 10.  
Page 10  
Confirm the reserveprogram  
When "Reservation" becomes active, thenixie tube  
displays the timeto the endof the reservedwash cycle, and  
the indicator turnson.During reserve procedure,pushthe  
"Reservation" button to displaythe reserve mode.  
To change the runningprogram or cancelthe reservation,  
you should cutoff the supplyand reselect.  
the washing will finish  
about 18 hours later  
5 Press the "start/pause" button  
START  
PAUSE  
Close the top lid  
During running , if the top cover is opened, the washing machine will stop  
running and alarm.  
Finish washing  
The washing machine cuts off the power supply automatically when wash cycle ends.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
When washing, lint filter must be used  
After using, please clean it in time.  
Lint filter:  
Clean  
1.Pull upward to detach  
Figure 1  
2.Clean the lint  
Put it in water and clean while it is still wet.  
(See to Figure 1).  
Install  
Dismantle  
3.Press downward to assemble.  
Figure 2  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Wipe it with neutral detergent.  
The filter screen of the water inlet  
valve is likely to be blocked by  
foreign materials andinfluence  
the water inlet. Please clean it  
Do not wipe it with thinner, petrol,  
alcohol etc.  
hol  
Alco  
inner  
Th  
Petrol  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending it to  
repair. If there are real breakdowns, please come to the special maintenance department or  
after-sale service department of our company. Do not repair it byyourself.  
The reason  
How to settle  
Phenomena  
Buzzing upon reservation starts,  
Nixie tube indicates "E0".  
Close the top lid.  
The top lid is not closed.  
Put down the drain hose.  
Is the drain hose put down?  
Is the drain hose blocked  
by foreign material?  
No or slow drain, nixie tube  
indicates "E1" , buzzing.  
Open and close the top lid once.  
Clean the foreign material.  
Open and close the top lid once.  
Running pauses , nixie tube  
indicates "E2", buzzing.  
The top cover leaves open.  
Close the top lid.  
Re-order the laundries. Close the  
top lid.  
Level the machine in right position.  
Open and close the top lid once.  
Safety switch actuates, not spin,  
(after self-correction twice),  
nixie tube displays "E3", buzzing.  
Are the laundries put  
slantingly?  
Is the machine slanting?  
The water tap is not open  
The water inlet valve is blocked  
Open the water tap. Push the  
"Start/Pause" button.  
Clean the water inlet valve.  
Push the "Start/Pause" button.  
Wait for the normal water pre-  
ssure before use.  
No or slow water filling not  
reaching the level in 15min  
nixie tube indicates "E4",  
buzzing.  
,
The water pressureis too  
low and thecurrent is  
too small.  
If the nozzle is choked with  
foreign bodies.  
Remove the foreign bodies.  
Poor or no waterfall flow.  
Not wash  
Is there power failure?  
Is the power plug loose?  
Use it when the power is on.  
Insert the power plug tightly.  
Affusion to the set water level.  
Does the water level arrive at the  
set water level?  
The machine  
does not act.  
Insert the power plug tightly.  
Close the top lid.  
Put the laundries orderly.  
Is the power plug loose?  
Is the top lid closed?  
Are the laundries put orderly?  
Not spin  
Level the machine properly.  
Re-order the laundries.  
Is the machine slanting?  
There's abnormal sound  
inside the machine.  
Are the laundries slanting in  
spinning?  
Is the jointer screw of the water  
inlet hose is loose or twisted  
awry?  
Fasten the jointer screw  
properly.  
The water faucet leaks.  
Common phenomena  
Phenomena  
Explanation  
The spinning is intermittent when it starts.  
Balance the laundries to avoid slanting.  
The program is setting the drain time. Some time is  
needed before it starts spinning.  
Push the "Procedure selection" button to  
select "Spin", but it doesn't work.  
It is the water remained in the factory inspection of  
performance.  
There may be some water flowing out of  
the drain hose in the first use of the machine.  
While water filling in wash and rinse, the  
pulsator pauses rotation  
To prevent splash during water filling.  
Supplementary water filling 48 s after  
sensor tests cloth material.  
Wash pauses  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing list  
Name  
Quantity  
One piece  
User's manual  
Components of thewater  
inlet hose  
One piece  
One piece  
Lint filter  
Bottom plate  
One piece  
Tapping screws  
Seven pieces  
One set  
Full automatic washingmachine  
Specification  
High/About 48 L Medium/About 37L  
Low/About 30L Very low/About 20L  
Water level/Water  
quantity (about)  
0.03MPa-1MPa  
Water inlet pressure  
Rated washing /  
spinning capacity  
5.0kg  
/5.0kg  
MADE IN CHINA  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Switch T20550 User Manual
Haier Flat Panel Television HLC15E User Manual
Harbor Freight Tools Paint Sprayer 91009 User Manual
Harbor Freight Tools Welding System 93096 User Manual
Havis Shields Automobile Parts KK K9 F14 K PT User Manual
Heath Zenith Door SL 6190 Series User Manual
HP Hewlett Packard Computer Drive D2D User Manual
HP Hewlett Packard Computer Monitor CV7540 User Manual
HP Hewlett Packard Stereo Equalizer 70205A User Manual
Husky Nail Gun HDN104 User Manual