Ser vice Ha n d book
®
HP VISUALIZE B2000 UNIX Wor k sta tion
Ma n u fa ct u r in g Pa r t Nu m b er : H P Pa r t No. A5983-90039
P r in t ed in USA J a n u a r y 2000
E d it ion E 0100
Download from Www.Somanuals.com. All Manuals Search And Download.
7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE
EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN
OR ORAL, IS EXPRESSED OR IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY
IMPLIED
WARRANTIES
OR
CONDITIONS
OF
MERCHANTABILITY,
SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.
8. HP will be liable for damage to tangible property per incident up to the greater of
$300,000 or the actual amount paid for the product that is the subject of the claim, and
for damages for bodily injury or death, to the extent that all such damages are
determined by a court of competent jurisdiction to have been directly caused by a
defective HP product.
9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS
WARRANTY STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE
REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR ITS
SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR
OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE
WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE
EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY
AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS
APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
Rest r ict ed R igh ts Legen d
Use, duplication, or disclosure by the U.S. Government Department of Defense is subject to
restrictions as set forth in paragraph (b)(3)(ii) of the Rights in Technical Data and
Software clause in DFARS 252.227.7013.
© Copyright 2000 Hewlett-Packard Company. All Rights Reserved.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced or translated to
another language without the prior written consent of Hewlett-Packard Company.
UNIX is a registered trademark in the United States and other countries, licensed
exclusively through X/Open Company Limited.
© Copyright 1980, 1984 AT&T, Inc.
© Copyright 1979, 1980, 1983 The Regents of the University of California.
This software and documentation is based in part on the Fourth Berkeley Software
Distribution under license from the Regents of University of California.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
P r in t in g H istor y
New editions of this manual incorporate all material updated since the previous edition.
Update packages may be issued between editions and contain replacement and additional
pages to be merged into the manual by the user.
The manual part number and printing date indicate its current edition. The manual part
number changes when extensive technical changes are incorporated. The printing date
changes when a new edition is printed. (Minor corrections and updates which are
incorporated at reprint do not cause the date to change.)
HP P a r t Nu m ber
P r in t in g Da t e
E d it ion
A5983-90039
January 2000
First
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Con ten t s
1. P r od u ct In for m a t ion
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Front Panel Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
System LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Internal Storage Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Rear Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
I/O Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Monitor Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Serial Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
USB Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LAN Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Parallel Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Audio Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
TOC Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Security Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Power Cord Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Keyboard and Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
USB HP Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
USB HP Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Operating System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Memory Failures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
2. Con figu r a tion
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Workstation Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
System Hardware Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Internal Storage Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Con ten t s
I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Monitor-Type Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3. Tr ou b lesh oot in g
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Flowcharts for Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Identifying LCD-Indicated Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Fan Faults and Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Dealing with a Boot Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Searching for Bootable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Stable Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Boot Command Notations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Supported Boot Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
ISL Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Selftest Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chassis Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Memory Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Running System Verification Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Running ODE-Based Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Using the PIM Dump Tool to Decode HPMCs . . . . . . . . . . . . . . . . . . . . 79
4. Field R ep la cea b le Un its
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Exploded View Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Exchange and Non-Exchange Part Numbers . . . . . . . . . . . . . . . . . . . . . 84
FRU Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Power Switch/LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Removable Media Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Con ten t s
I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Memory DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Voltage Regulator Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
System Board Tray Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
5. Block Dia gr a m
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
6. Boot Con sole H a n d ler
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
Boot Console Handler Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Accessing the Boot Console Handler . . . . . . . . . . . . . . . . . . . . . . . . . . .142
Booting the Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
Searching for Bootable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
Resetting the Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
Displaying and Setting Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Displaying and Setting the Monitor Type . . . . . . . . . . . . . . . . . . . . . . .150
The Monitor Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
Displaying the Current Monitor Configuration . . . . . . . . . . . . . . . . .151
Setting the Monitor Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
Setting the Monitor Type with SAM . . . . . . . . . . . . . . . . . . . . . . . . . .152
Setting the Monitor Type at Power On . . . . . . . . . . . . . . . . . . . . . . . .154
Troubleshooting Monitor Problems . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Displaying the Current Memory Configuration. . . . . . . . . . . . . . . . . . .156
Memory Information Sample. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
Displaying the Status of the I/O Slots . . . . . . . . . . . . . . . . . . . . . . . . . .157
Setting the Auto Boot and Auto Search Flags . . . . . . . . . . . . . . . . . . . .158
Displaying and Setting the Security Mode . . . . . . . . . . . . . . . . . . . . . .159
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Con ten t s
Displaying and Setting Fastboot Mode . . . . . . . . . . . . . . . . . . . . . . . . . 160
Displaying the LAN Station Address . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Displaying System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Displaying PIM Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Stable Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
ISL Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Invoking ISL from the Boot Console Handler . . . . . . . . . . . . . . . . . . 163
ISL User Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Obtaining and Updating System Firmware . . . . . . . . . . . . . . . . . . . . . 165
A. P r od u ct Sp ecifica tion s
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
DC Magnetic Field Interference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Electromagnetic Compatibility (EMC). . . . . . . . . . . . . . . . . . . . . . . . 168
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Humidity (Non-condensing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Leakage Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Line Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
B. R egu la tor y a n d Sa fet y Sta t em en ts
Appendix Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Emissions Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
For FCC B Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Third-Party Emissions Regulations Compliance . . . . . . . . . . . . . . . . . 176
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Con ten t s
Special Regulatory and Safety Information . . . . . . . . . . . . . . . . . . . . . .176
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176
Laser Safety Statement (U.S.A. Only). . . . . . . . . . . . . . . . . . . . . . . . .176
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176
Electrostatic Discharge (ESD) Precautions . . . . . . . . . . . . . . . . . . . . . .177
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178
C. R ela ted Docu m en t a tion
HP CE Training CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
User Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
Glossa r y
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Con ten t s
10
Download from Www.Somanuals.com. All Manuals Search And Download.
F igu r es
Figure 1-1. Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 1-2. LCD Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 1-3. CD Drive Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 1-4. Floppy Disk Drive Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 1-5. Rear Panel Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 1-6. Audio Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 1-7. Security Loop Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 1-8. Closed Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2-1. CD Drive Jumper Setting (Rear View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 2-2. Memory Slot Numbers and Loading Sequence . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 2-3. PCI Card Slot Numbering and Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 3-1. Main (Power on LCD) Troubleshooting Flowchart . . . . . . . . . . . . . . . . . . . . . . 43
Figure 3-2. Console Troubleshooting Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 3-3. Bootable Device Troubleshooting Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 3-4. HP-UX Troubleshooting Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 3-5. Fan Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 4-1. Exploded View Diagram of the B2000 Workstation FRUs . . . . . . . . . . . . . . . 83
Figure 4-2. Opening the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 4-3. Opening the Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 4-4. Removing the Power Switch/LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 4-5. Removing the CD Drive Bay’s Rear Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Figure 4-6. Front of the Workstation with the Front Panel Removed . . . . . . . . . . . . . . . . 92
Figure 4-7. Removing the CD Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 4-8. Installing the CD Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Figure 4-9. Tightening the Bracket Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Figure 4-10. Plugging in the Audio, ATAPI, and Power Cables . . . . . . . . . . . . . . . . . . . . . 94
Figure 4-11. Replacing the CD Drive Bay’s Rear Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Figure 4-12. Removing the Floppy Disk Drive Bay’s Rear Cover . . . . . . . . . . . . . . . . . . . . 96
Figure 4-13. Front of Workstation with the Front Panel Removed . . . . . . . . . . . . . . . . . . 97
Figure 4-14. Removing the Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Figure 4-15. Installing the Floppy Disk Drive Blank and Bracket . . . . . . . . . . . . . . . . . . 98
Figure 4-16. Tightening the Bracket Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Figure 4-17. Replacing the Floppy Disk Drive Bay’s Rear Cover . . . . . . . . . . . . . . . . . . . . 99
Figure 4-18. Removing the Floppy Disk Drive Bay’s Rear Cover . . . . . . . . . . . . . . . . . . . 100
Figure 4-19. Front of Workstation with the Front Panel Removed . . . . . . . . . . . . . . . . . 100
Figure 4-20. Removing the Floppy Disk Drive Bracket and Blank . . . . . . . . . . . . . . . . . 101
Figure 4-21. Installing the Floppy Disk Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Figure 4-22. Tightening the Bracket Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Figure 4-23. Plugging in the Power and Data Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
11
Download from Www.Somanuals.com. All Manuals Search And Download.
F igu r es
Figure 4-24. Replacing the Floppy Disk Drive Bay’s Rear Cover . . . . . . . . . . . . . . . . . . . 103
Figure 4-25. Location of the Hard Disk Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 4-26. Removing the Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 4-27. Removing the Hard Disk Drive from Its Bracket . . . . . . . . . . . . . . . . . . . . . 106
Figure 4-28. Replacing the Hard Disk Drive Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Figure 4-29. Location of the Hard Disk Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 4-30. Removing the T-15 Torx Mounting Screws . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Figure 4-31. Positioning the Bracket on to the Hard Disk Drive . . . . . . . . . . . . . . . . . . . 108
Figure 4-32. Mounting the Bracket on to the Hard Disk Drive. . . . . . . . . . . . . . . . . . . . . 108
Figure 4-33. Positioning the Hard Disk Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 4-34. PCI Card Slot Numbering and Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . 110
Figure 4-35. B2000 System Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Figure 4-36. I/O Slot Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Figure 4-37. Removing the I/O Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Figure 4-38. Location of the Real Time Clock Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Figure 4-39. System Board View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Figure 4-40. DIMM Connectors on the System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Figure 4-41. Removing Memory Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Figure 4-42. System Board View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Figure 4-43. Memory Slot Numbers and Loading Sequence . . . . . . . . . . . . . . . . . . . . . . . 116
Figure 4-44. B2000 System Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Figure 4-45. Installing a DIMM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Figure 4-46. Screws Holding the Power Supply in Place . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Figure 4-47. Screws Holding the Power Supply in Place . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Figure 4-48. The Voltage Regulator Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Figure 4-49. Master and Slave Voltage Regulator Modules. . . . . . . . . . . . . . . . . . . . . . . . 123
Figure 4-50. Fan Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Figure 4-51. Removing the Air Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Figure 4-52. Removing the I/O Fan from the Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Figure 4-53. Location of the Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Figure 4-54. Removing the Air Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Figure 4-55. Removing the Speaker from the Mounting Bracket . . . . . . . . . . . . . . . . . . . 128
Figure 4-56. Screws Holding the System Board Tray Assembly in Place . . . . . . . . . . . . . 130
Figure 5-1. Functional Block Diagram of the B2000 Workstation . . . . . . . . . . . . . . . . . . 134
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta bles
Table 1-1. Key Features of the B2000 Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 1-2. CD Drive Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 1-3. Floppy Disk Drive Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 1-4. Serial I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 1-5. Audio Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 3-1. Fan Numbers and Corresponding Names. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 3-2. Chassis Codes for the B2000 Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 4-1. Exchange Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Table 4-2. Non-Exchange Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Table 6-1. System Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Table 6-2. Mnemonic Style Notation for Boot Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta bles
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1 P r od u ct In for m a tion
This chapter provides general product information about the HP VISUALIZE B2000
workstation. This information is provided to help familiarize you with the main features
and components of this workstation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Chapter Overview
Ch a p t er Over view
This chapter contains the following main sections:
•
•
•
•
•
•
•
Product Description
Front Panel Components
Rear Panel Components
Monitors
Keyboard and Mouse
Operating System Overview
Memory
P r od u ct Descr ip tion
The HP VISUALIZE B2000 is an entry-level HP-UX workstation with a 400 MHz PA-RISC
processor in a mid-tower case. It supports 4 memory slots, 4 PCI (Peripheral Connect
Interface) I/O slots, and entry-level and mid-level HP VISUALIZE graphics.
Table 1-1 lists the key features of the HP VISUALIZE B2000 workstation.
Ta ble 1-1. Key Fea tu r es of th e B2000 Wor k sta tion
Feature
Description
Processor
400 MHz PA-RISC processor with 1.5 MB cache
Operating
System
HP-UX version 10.20 with the 9912 Additional Core Enhancements (ACE)
software bundle (December 1999)
User Interface
Compatibility
Main Memory
HP Common Desktop Environment (CDE) graphical user interface
Source and binary code compatible with the B- and C-Class product families
Four memory slots supporting 128MB, 256MB, and 512 MB memory DIMMs.
Minimum memory configuration is 256 MB, and maximum is 2 GB.
Internal Storage
Devices
•
One standard 9 GB 7200 RPM Ultra2 Wide Low-Voltage Differential
(LVD) SCSI hard disk drive; a second 9 GB 7200 RPM Ultra2 Wide LVD
SCSI hard disk drive is optional
•
•
One standard ATAPI fast CD drive
One optional 3.5-inch floppy disk drive
Standard
Ethernet IEEE 802.3, RJ 45 Twisted Pair 10/100 BaseT
Networking
16
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Chapter Overview
Ta ble 1-1. Key Fea t u r es of t h e B2000 Wor k st a t ion
Feature
Description
Standard I/O
•
•
•
•
Two Serial (RS-232) ports
Two USB (Universal Serial Bus) ports
One Parallel (IEEE 1284) port
Four Audio ports (Line In, Line Out, Microphone In, and Headphones Out)
I/O Expansion
Capabilities
Four PCI (Peripheral Connect Interface) slots:
•
•
Two 64-bit PCI-2X slots at 5V, 33 MHz
Two 32-bit PCI-1X slots at 5V, 33MHz
Monitors
Currently
Supported
•
•
•
21-inch, 1280×1024 (stereo capable) color, 75 Hz, VESA
21-inch, 1600×1200 color, 75 Hz, VESA
19-inch, 1280×1024 color, 75 Hz, VESA
Graphics
•
•
Integrated HP VISUALIZE-fxe graphics chip on the system board
HP VISUALIZE-fxe graphics card (optional)
Keyboard
Mouse
USB (Universal Serial Bus) HP keyboard
USB (Universal Serial Bus) HP three-button mouse (standard), or
USB HP scroll-wheel mouse (optional)
Chapter 1
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Front Panel Components
Fr on t Pa n el Com p on en ts
Figure 1-1 shows the components that are located on the front panel of the B2000
workstation. The following subsections describe the system LCD, power switch, and the
internal storage devices (including the standard CD drive and optional floppy disk drive)
that are located on the front panel.
Figu r e 1-1. Fr on t Pa n el Com p on en t s
System LCD
Power
Switch
CD Drive
Bay for
Optional
Floppy
Disk Drive
System LCD
The Liquid Crystal Display (LCD) is located on the left side of the front panel as part of the
power switch/LCD assembly. The LCD lights when the workstation power is on. The LCD
has a 2-line display, with up to 16-characters per line. It displays messages about the state
of the system, which are called chassis codes. See the section titled “Selftest Failures” on
page 53 in Chapter 3 for a complete listing of the possible chassis codes which can be
displayed on the LCD.
The following symbols appear on the LCD, representing different system activities.
Figu r e 1-2. LCD Sym bols
Operating system running
Disk Access in progress
Network Receive in progress
Network Transmit in progress
18
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Front Panel Components
Pow er Sw itch
The power switch is also located on the left side of the front panel as part of the power
switch/LCD assembly. Use the power switch to power the workstation on and off.
When you press the power switch to power off the workstation, the operating system
executes an automatic shutdown -qcommand. This prevents any damage to programs
and data on the system disk.
Pressing the power switch on again automatically boots up the HP-UX operating system, if
the system has been configured to auto boot. For information on setting auto boot, refer
to the section “Setting the Auto Boot and Auto Search Flags” on page 158.
In ter n a l Stor a ge Devices
The B2000 workstation supports the following internal storage devices:
•
•
•
Up to two hard disk drives
One CD drive
Optionally, one floppy disk drive
The following subsections describe these internal storage devices.
Ha r d Disk Dr ives
The B2000 workstation has one 9 GB 7200 RPM Ultra2 Wide Low-Voltage Differential
(LVD) SCSI hard disk drive as a standard component. Optionally, the workstation also
supports a second 9 GB 7200 RPM Ultra2 Wide LVD SCSI hard disk drive.
CD Dr ive
The B2000 workstation has one ATAPI fast CD drive as a standard component. Figure 1-3
shows the operating features of the CD drive, and Table 1-2 describes these features.
NOTE
The B2000 workstation supports one CD drive only.
Figu r e 1-3. CD Dr ive Fea t u r es
Emergency
Eject Hole
Disk
Tray
Eject
Button
Busy
Indicator
Headphones
Jack
Audio
Control
Thumbwheel
Chapter 1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Front Panel Components
Ta ble 1-2. CD Dr ive Fea tu r es
Feature
Purpose
Disk Tray
Holds the CD disk. (Note that this style of CD drive does not
use a disk caddy.)
Headphones Jack
Allows headphones to be connected to the CD drive for audio.
Controls the volume of a CD disk that has audio.
Audio Control Thumbwheel
Busy Indicator
Lights during a data access operation and blinks during a
data transfer. The indicator blinks initially and then stays lit
when there is one of the following.
•
•
•
A defective disk
A disk insertion error (for example, an upside down disk)
No disk present
Eject Button
Opens the disk tray so that a CD disk may be inserted in it or
removed from it. When the CD drive is in use, press the eject
button for more than one second to open the disk tray. (Note
that the disk tray does not open if the workstation power is
off.) Then press it again to close the disk tray.
Emergency Eject Hole
Opens the disk tray when you insert a paper clip into it. Used
when the workstation does not have power and the disk tray
cannot be opened by pressing the eject button.
NOTE
The audio features of the CD drive are supported through applications only.
One such application is xmcd. The xmcdutility is not a part of HP-UX; it can
be downloaded from the web at this URL:
http://metalab.unc.edu/tkan/xmcd
20
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Front Panel Components
F lop p y Disk Dr ive (Op t ion a l)
The optional floppy disk drive is a 3.5-inch form factor device with a PC/AT interface. It
connects to the workstation via a 34-pin PC/AT ribbon cable and a 4-pin power cable. The
floppy disk drive has up to 1.44 MB capacity depending on the media and format used.
Figure 1-4 shows the features of the floppy disk drive, and Table 1-3 describes these
features.
NOTE
The B2000 workstation supports one floppy disk drive only.
Figu r e 1-4. F lop p y Disk Dr ive Fea t u r es
Activity LED
Eject Button
Ta b le 1-3. F lop p y Disk Dr ive Fea t u r es
Feature
Purpose
Activity LED
Illuminates during a data access operation and
blinks during a data transfer.
Eject Button
Ejects a floppy disk from the drive when pressed.
Chapter 1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Rear Panel Components
Rea r Pa n el Com p on en ts
This section describes the following components that are located on the rear panel of the
B2000 workstation:
•
•
•
•
•
•
•
•
•
•
I/O slots
Monitor connector
Serial (RS-232) connectors
USB (Universal Serial Bus) connectors
LAN (Ethernet IEEE 802.3, RJ 45 Twisted Pair 10/100 BaseT) connector
Parallel (IEEE 1284) connector
Audio connectors (Line In, Line Out, Microphone In, and Headphones Out)
TOC (Transfer Of Control) button
Security loop
Power cord connector
Figure 1-5 shows the locations of the components on the rear panel of the B2000
workstation. The following subsections describe each of these components.
Figu r e 1-5. Rea r Pa n el Com p on en t s
Four I/O Slots
Security Loop
Monitor Connector
Two Serial Connectors
Two USB Connectors
LAN Connector
USB Cable Clip
Parallel Connector
Four Audio Connectors:
Line In
Line Out
Microphone In
Headphones Out
TOC Button
Power Cord
Connector
22
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Rear Panel Components
I/O Slot s
The four I/O slots located at the top left of the rear panel are PCI (Peripheral Connect
Interface) slots, which can be used for add-on I/O interface cards. There are two PCI-2X
slots and two PCI-1X slots, which are defined as follows:
Slot 1: 64-bit PCI-2X at 5V, 33 MHz
Slot 2: 64-bit PCI-2X at 5V, 33 MHz
Slot 3: 32-bit PCI-1X at 5V, 33 MHz
Slot 4: 32-bit PCI-1X at 5V, 33 MHz
Mon itor Con n ector
The B2000 workstation has an integrated HP VISUALIZE-fxe graphics chip on the system
board. Thus, the monitor connector on the rear panel of the workstation connects the
monitor to this graphics chip on the system board.
Ser ia l Con n ector s
There are a variety of pointing devices (such as a mouse or trackball) or peripheral devices
(including printers, plotters, modems, and scanners) that can be attached to the two
RS-232 Serial Input/Output (SIO) ports on the rear panel of this workstation. Refer to the
label on the rear of the workstation to locate serial port 1 and serial port 2. Consult the
documentation that accompanies each pointing device or peripheral device for specific
information concerning its use.
The SIO ports are programmable, allowing functions such as bit rate, character length,
parity, and stop bits to be set. You can set these by using the HP-UX System
Administration Manager (SAM) utility, or by selecting a system special device file with the
functions already programmed. The SIO ports are used as interfaces for serial
asynchronous devices to the CPU.
Table 1-4 shows the SIO connector pin listings. The serial connectors are 9-pin D-sub
connectors. Signal names are those specified in the EIA RS-232 standard.
Ta ble 1-4. Ser ia l I/O P in s
Pin No. Signal Description
1
2
3
4
5
6
DCD
RXD
TXD
DTR
GND
DSR
Data Carrier Detect
Receive Data
Transmit Data
Data Terminal Ready
Ground
Data Set Ready
Chapter 1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Rear Panel Components
Ta ble 1-4. Ser ia l I/O P in s
Pin No. Signal Description
7
8
9
RTS
CTS
RI
Request To Send
Clear To Send
Ring Indicator
USB Con n ector s
The USB connectors located on the rear panel of the workstation provide interfaces for the
keyboard and mouse to the system. These USB connectors support only the HP keyboard,
HP mouse, USB hub, or other HP-recommended USB devices. The keyboard and mouse
may be plugged into either USB connector on the rear of the workstation or plugged into
the USB hub. No other USB configuration is currently supported. Consult the
documentation that accompanies each USB input device for specific information
concerning its use.
NOTE
The USB HP keyboard and USB HP three-button mouse are shipped with the
B2000 workstation. The USB hub and USB HP scroll-wheel mouse may be
ordered separately.
For more information on USB, see the Universal Serial Bus website at the following URL:
http://www.usb.org
CAUTION
NOTE
Use of USB devices other than those approved by HP may result in
unpredictable functionality and inferior performance of the B2000
workstation.
The USB cable clip on the rear of the workstation (see Figure 1-5 on page 22)
provides strain relief for USB cables. To secure USB cables, open the cable
clip, loop the cables through the clip, and snap it closed.
LAN Con n ector
The B2000 workstation has one built-in, Ethernet IEEE 802.3, RJ 45 Twisted Pair (TP)
connector for 802.3 (Ethernet) or 10/100BaseT networking. The workstation automatically
selects the correct network setting.
Pa r a llel Con n ector
The 25-pin HP Parallel I/O interface uses IEEE 1284 I/O interface protocols to support
peripheral devices such as printers and plotters. Consult the documentation that
accompanies each peripheral device for specific information concerning its use.
24
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Rear Panel Components
Au d io Con n ector s
The B2000 workstation has audio-input and -output capabilities through external input
and output connectors on the rear panel and through an internal speaker. The sound is
16-bit, 44 kHz (CD-quality).
As shown in Figure 1-6, the workstation’s rear panel contains four audio connectors: Line
In, Line Out, Microphone In, and Headphones Out.
Figu r e 1-6. Au d io Con n ect or s
Line In
Line Out
Microphone In
Headphones Out
The audio connectors are standard stereo audio mini-jacks. Hewlett-Packard recommends
using gold-plated plugs available through audio retailers for best quality recording and
playback through the external connectors.
Table 1-5 summarizes the audio electrical specifications for the B2000 workstation.
Ta b le 1-5. Au d io E lect r ica l Sp ecifica t ion s
Frequency Response
25 Hz to 20 kHz
Input Sensitivity/Impedance:
Line In
Microphone In
2.8Vp-p/10Kohm
40mVp-p/47Kohm
Maximum Output Level/Impedance:
Line Out
Headphones Out
2.8Vp-p/920ohm
5.6Vp-p/110ohm
TOC Bu tton
The TOC (transfer of control) button interrupts the system and transfers control from the
default device to an auxiliary device. A transfer of control saves the state of the processor
in Processor Internal Memory (PIM) and begins execution of recovery software at a
nonzero location specified by a special location in Page Zero called MEM_TOC. The TOC
code is protected by a checksum.
Chapter 1
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Rear Panel Components
Secu r ity Loop
There is also a security loop on the rear panel of the B2000 workstation. The security loop
allows you to lock the workstation’s left side panel, thus securing the internal components
of the workstation. Figure 1-7 provides a view of the security loop.
Figu r e 1-7. Secu r it y Loop Com p on en t s
Security
Loop Pin
Hole
Security
Loop Pin
and Spring
To lock the workstation’s left side panel, follow these steps:
1. Make sure the workstation’s left side panel is closed, as shown in Figure 1-8.
Figu r e 1-8. Closed Left Sid e P a n el
Workstation’s
Front Panel
Left Side Panel
(Using the Front
Panel as Reference)
26
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Monitors
2. Push the security loop’s pin into the security loop pin hole, and insert the padlock’s latch
through the holes at the top and bottom of the security loop. This locks the left side
panel.
3. Lock the padlock. The workstation’s left side panel is now secure.
Pow er Cor d Con n ector
Plug the workstation’s power cord into the power cord connector to provide AC power to
the system.
Mon itor s
The B2000 workstation supports monitors set to one of the following resolutions:
•
•
•
1280×1024 color (stereo capable), 75Hz, VESA
1600×1200 color, 75Hz, VESA
1280×1024 color, 75 Hz, VESA
The workstation must have either an HP-supported monitor running at 75 Hz with a
1280×1024 resolution, or a full multi-mode color monitor. Monitors with EVC, D-Sub, or 5
BNC connectors (RGB, vertical sync, horizontal sync) will function.
NOTE
The HP VISUALIZE-fxe graphics card will not function with older HP monitor
types that use a sync on green signal. This includes monitors such as the
HP 1097A/B/C/D, A2088A, and A2828A/B that only have 3 BNC connectors.
Note that you can connect the B2000 workstation to earlier HP monitors with 15-pin
miniature D-Sub cables using the A4168A adapter shipped with the workstation’s
accessory kit.
Before using a monitor, you should become familiar with its controls, connectors, and
indicators. For information about using a monitor, see the documentation that came with
the monitor.
Chapter 1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Keyboard and Mouse
Keyboa r d a n d Mou se
USB HP Keyboa r d
The HP VISUALIZE B2000 workstation supports a USB HP keyboard. The keyboard
shipped with the workstation provides a localized PC-104, PC-105, PC-106, or J IS-109
compatible input device for USB-equipped PA-RISC workstations and other
USB-compatible computers that support the HP-UX operating system. The keyboard
includes a captive cable terminated in a USB Style A connector.
The USB keyboard is designed specifically for use with HP workstations. All keyboard
models with the exception of the J IS-109 layout may also be compatible with conventional
personal computers.
Some applications may expect to use keycodes generated by keys existing on other types of
keyboards. Consult the documentation that accompanies each input device for specific
information concerning its use.
NOTE
HIL and PS/2 devices are not supported by the B2000 workstation.
USB HP Mou se
The HP VISUALIZE B2000 workstation supports a USB HP mouse. The USB HP
three-button mouse is standard, whereas the USB HP scroll-wheel mouse is optional.
For general information on the various cursor shapes associated with different areas of HP
CDE while using a mouse, see the Using Your HP Workstation manual.
28
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Operating System Overview
Op er a t in g System Over view
The B2000 workstation runs the HP-UX operating system version 10.20 with the 9912
Additional Core Enhancements (ACE) software bundle (December 1999). To verify which
version of the operating system is running on a B2000 workstation, use the command
swlistin a terminal window. Note that the ACE software bundle releases are also
available at the following URL:
http://software.hp.com/
The B2000 workstation is an Instant Ignition system (that is, a system with preloaded
software). It has X-Windows, HP’s graphical user interface, and HP CDE (Common
Desktop Environment) already installed and configured. If the Instant Ignition system
does not have the kernel preconfigured with all of the required device drivers, refer to the
Managing Systems and Workgroups manual to configure the kernel. If you have any
questions about Instant Ignition, refer to the Using Your HP Workstation manual.
Note that you can find both of the manuals mentioned in the previous paragraph on HP’s
documentation website at the following URL:
http://www.docs.hp.com/
Chapter 1
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
Memory
Mem or y
The B2000 workstation has four slots for memory DIMMs. You can install only 128 MB,
256 MB, or 512 MB DIMMs in these slots. The minimum memory configuration for a
B2000 workstation is 256 MB, and the maximum is 2 GB.
To install memory DIMMs, refer to “Replacing or Installing Additional Memory DIMMs”
on page 115.
CAUTION
If memory is installed improperly or is defective, the B2000 workstation’s
operating system will not boot-up, and a DIMM error chassis code will appear
in the LCD. If an error does occur, refer to Chapter 3, “Troubleshooting.”
Mem or y Fa ilu r es
The HP VISUALIZE B2000 system (with HP-UX 10.20 and later) uses Memory Page
Deallocation, a feature that allows the system to provide information to the operating
system about memory failures.
You can use the memrptcommand with the detailswitch to obtain information about the
Memory Page Deallocation Table (PDT) as well as single bit errors logged by the system,
by typing the following:
# /usr/sbin/sysdiag Enter
DUI>logtool Enter
LOGTOOL>memrpt detail Enter
The PDT can also be checked using the pdt command in the Service menu of the Boot
Console Handler (refer to Chapter 6). If you replace a defective DIMM, use the Service
Menu’s pdt clearcommand to clear out the PDT.
30
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Con figu r a tion
This chapter provides details about setting up and changing the workstation and system
hardware configuration for the HP VISUALIZE B2000 workstation.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
Chapter Overview
Ch a p t er Over view
This chapter contains the following main sections:
•
•
Workstation Configurations
System Hardware Configurations
— Internal Storage Devices
— Memory
— I/O Cards
— Monitor-Type Selection
Wor k st a tion Con figu r a tion s
Refer to the HP Workstations website for a complete list of supported accessories,
peripherals, and operating system versions for the HP VISUALIZE B2000 workstation. The
URL for the website is:
http://hp.unixworkstations.com
System Ha r d w a r e Con figu r a tion s
This section provides information for setting up or changing the configuration of the Field
Replaceable Units (FRUs) for the B2000 workstation.
In ter n a l Stor a ge Devices
Ha r d Disk Dr ive Con figu r a t ion
The SCSI IDs for hard disk drives are hard-wired into the SCA Ultra2 Wide LVD SCSI
interfaces on the system board within the B2000 workstation. Hence, SCSI IDs do not need
to be set for the hard disk drives (up to two) installed in this workstation. From top to
bottom, the pre-set SCSI IDs for hard disk drives are: 6 and 5.
Similarly, no jumpers are installed at the factory, nor is any jumper installation required at
the customer’s site, on the hard disk drive model supported with the B2000 workstation.
To remove and replace or install a hard disk drive, see the section titled “Hard Disk
Drives” on page 104. Also see the next subsection, “Configuring a Hard Disk Drive as a File
System,” when removing or installing a hard disk drive.
32
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
Con figu r in g a H a r d Disk Dr ive a s a File Syst em
This section describes how to use SAM to add a hard disk drive to the workstation as a file
system and how to remove the hard disk drive from the workstation. For more information
about configuring a hard disk drive, refer to the Managing Systems and Workgroups
manual.
The procedures in this section require you to log in as root. If you cannot log in as root,
contact the system administrator.
Ad d in g a H a r d Disk Dr ive a s a File Syst em
To add a hard disk drive as a file system using SAM, do the following:
1. Log in as root.
2. Move the mouse pointer to the Ap p lica t ion Ma n a ger control for tools and click the left
mouse button. Alternatively you can execute samat a terminal window command
prompt and skip to step 5.
3. Double-click on the Syst em _Ad m in icon in the Ap p lica t ion Ma n a ger window.
Chapter 2
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
4. Double-click on the Sa m icon in the Ap p lica t ion Ma n a ger -- Syst em _Ad m in window.
If you are root, the System Application Manager (SAM) will appear on the screen.
5. Double-click on the Disk s a n d F ile Syst em s icon.
6. Double-click on the Disk Devices icon.
The following screen message is displayed:
Scanning the system’s hardware...
The Disk a n d F ile Syst em s window opens containing a list of drives installed in this
workstation. From the list of devices, choose the hard disk drive you would like to
configure as a file system by clicking on the device to highlight it.
7. Click on Ad d in the Actions menu. For this example you will select the item Not Usin g
t h e Logica l Volu m e Ma n a ger. However, you can select any appropriate item from the
Action s menu.
8. Enter the mount directory name (for example, /disk1) in the Mou n t Dir ect or y field of
the Ad d Disk w it h ou t LVM window.
9. Click on the OK button in the Ad d Disk w it h ou t LVM window. You will need to wait
for a short time before the new file system is created and the hard disk drive is
mounted. When the Ad d Disk w it h ou t LVM window disappears and HFS appears in
the Use column of the Disk a n d File Syst em s window, your task will be complete.
34
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
Rem ovin g a H a r d Disk Dr ive a s a F ile Syst em
To remove a hard disk drive as a file system using SAM, do the following:
1. Log in as root.
2. Move the mouse pointer to the Ap p lica t ion Ma n a ger control for tools and click the left
mouse button. Alternatively you can execute sam at a terminal window command
prompt and skip to step 5.
3. Double-click on the Syst em _Ad m in icon in the Ap p lica t ion Ma n a ger window.
4. Double-click on the Sa m icon in the Ap p lica t ion Ma n a ger -- Syst em _Ad m in window.
If you are root, the System Application Manager (SAM) will appear on your screen.
5. Double-click on the Disk s a n d F ile Syst em s icon.
Chapter 2
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
6. Double-click on the Disk Devices icon.
The following screen message is displayed:
Scanning the system’s hardware...
The Disk a n d F ile Syst em s window opens containing a list of devices installed in this
workstation. From the list of devices, choose the hard disk drive you would like to
remove (unmount) by highlighting that device.
7. Click on R em ove in the Action s menu. In the window that next appears, click on the
Yes button. This will unmount the file system located on the hard disk drive you are
removing from the workstation. You will need to wait for a short time before the new file
system is unmounted. The file system is successfully unmounted when you see Unused
in the Use column.
36
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
CD Dr ive Con figu r a tion
The CD drive connects to the ATAPI (IDE) interface in the CD drive bay backplane within
the B2000 workstation via a 40-pin ribbon cable, a 4-pin audio cable, and a 4-pin power
cable. No interface addressing is required for the CD drive.
However, as shown in Figure 2-1, the CD drive should have a jumper set on the CSEL
(Cable Select) selection pins. (The CD drive should ship from the factory already jumpered
for CSEL.)
CAUTION
CD drives are susceptible to mechanical and electrostatic shock. When
handling the drive, always wear the static-grounding wrist strap that came in
the CD drive kit. Always handle the drive carefully.
Figu r e 2-1. CD Dr ive J u m p er Set t in g (R ea r View )
Jumpered for CSEL
To remove and replace a CD drive in the B2000 workstation, see the section titled
“Removing and Replacing a CD Drive” on page 91.
F lop p y Disk Dr ive (Op tion a l) Con figu r a tion
The optional 3.5-inch floppy disk drive requires no ID, switch, or jumper settings. To
remove a floppy disk drive from the B2000 workstation, see the section titled “Removing a
Floppy Disk Drive” on page 96. To replace or install a floppy disk drive, see the section
titled “Replacing or Installing a Floppy Disk Drive” on page 99.
CAUTION
Floppy disk drives are susceptible to mechanical and electrostatic shock.
When handling the drive, always wear the static-grounding wrist strap that
came in the floppy disk drive kit. Always handle the drive carefully.
Chapter 2
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
Mem or y
The B2000 workstation has 4 memory slots, labeled SL0 through SL3. Memory can be
configured from 256 MB to 2 GB for the B2000 workstation. Memory does not have to be
configured in pairs for the B2000, but must be loaded in the order shown in Figure 2-2.
Notice the alternating load pattern by location on the system board.
Figu r e 2-2. Mem or y Slot Nu m b er s a n d Loa d in g Seq u en ce
Load 1st
SL0
Memory Slots
(4 Slots)
SL3
SL1
SL2
Load 4th
Load 2nd
Load 3rd
The B2000 workstation supports 128 MB, 256 MB, and 512 MB DIMMs. If you will install
different sizes of memory DIMMs in a particular workstation, load the largest size first
and then the smaller size for maximum performance. For example, load a 256 MB DIMM
in slot 0 (SL0) and then load a 128 MB DIMM in slot 1 (SL1).
CAUTION
NOTE
The memory DIMMs must be installed in the correct order, else the
workstation will not boot properly.
Users who wish to achieve both maximum performance and maximum future
capacity are advised to use 512 MB DIMMs exclusively.
To remove DIMMs, see the section titled “Removing Memory DIMMs” on page 114. To
replace or install DIMMs, see the section titled “Replacing or Installing Additional
Memory DIMMs” on page 115. Note that there is a system label on the floor of the
workstation’s interior showing the memory loading order for the B2000.
Use the Boot Console Handler to verify that the workstation recognizes the installed
memory. See “Displaying the Current Memory Configuration” on page 156.
38
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
I/O Ca r d s
The B2000 workstation’s system board has four Peripheral Connect Interface (PCI) slots
for option I/O cards. Slots 1 and 2 are full-size (PCI-2X) slots. Slots 3 and 4 are half-size
(PCI-1X) slots. See Figure 2-3 for a brief description of slot capabilities.
Figu r e 2-3. P CI Ca r d Slot Nu m b er in g a n d Ca p a b ilit ies
Slot 1
Slot 2
Slot 3
Slot 4
64-b its, 5V, 33MH z
64-b its, 5V, 33MH z
32-b its, 5V, 33MH z
32-b its, 5V, 33MH z
To remove and replace or install I/O cards, see the section titled “I/O Cards” on page 110.
NOTE
If you are installing an additional HP VISUALIZE-fxe graphics card, after you
connect the monitor to the additional graphics card, you must change the
graphics path for that monitor. To do this, see the section “Displaying and
Setting the Monitor Type” on page 150.
Chapter 2
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
System Hardware Configurations
Mon itor -Typ e Selection
The B2000 workstation supports monitors set to one of the following resolutions:
•
•
•
1280×1024 color (stereo capable), 75Hz, VESA
1600×1200 color, 75Hz, VESA
1280×1024 color, 75 Hz, VESA
The workstation must have either an HP-supported monitor running at 75 Hz with a
1280×1024 resolution, or a full multi-mode color monitor. Monitors with EVC, D-Sub, or 5
BNC connectors (RGB, vertical sync, horizontal sync) will function.
NOTE
The HP VISUALIZE-fxe graphics card will not function with older HP monitor
types that use a sync on green signal. This includes monitors such as the
HP 1097A/B/C/D, A2088A, and A2828A/B that only have 3 BNC connectors.
Note that you can connect the B2000 workstation to earlier HP monitors with 15-pin
miniature D-Sub cables using the A4168A adapter shipped with the workstation’s
accessory kit.
The monitor type does not have to change since the B2000 workstation is set up to
support the monitors listed above. However, if for some reason the monitor typeneeds to
change, refer to Chapter 6, “Boot Console Handler.”
40
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tr ou blesh ootin g
This chapter provides information about isolating a failing component, known as a Field
Replaceable Unit (FRU), in the HP VISUALIZE B2000 workstation.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Chapter Overview
Ch a p t er Over view
This chapter contains the following main sections:
•
•
•
•
•
•
•
•
•
Flowcharts for Troubleshooting
Identifying LCD-Indicated Conditions
Fan Faults and Warnings
Dealing with a Boot Failure
Selftest Failures
Memory Failures
Running System Verification Tests
Running ODE-Based Diagnostics
Using the PIM Dump Tool to Decode HPMCs
To troubleshoot an HP VISUALIZE B2000 workstation, you must be familiar with the
HP-UX operating system. You should also be familiar with the boot ROM diagnostics and
the Mesa (Support Tools Manager) online tests, which we describe in this chapter.
As a super-user who is troubleshooting an HP-UX system, you should be able to shutdown
and reboot a system, start and stop processes, and examine error logs. You should also be
able to use systems utilities such as ioscan to check device files and configurations,
swlist to show loaded patches and software bundles, and SAM to configure and show
enabled services and configurations. You should also be familiar with STM, the online
diagnostics tool. You can view man pages on any of these online utilities or commands.
Note any error or status messages, then run the power-up boot ROM diagnostics, known as
Self Test. If the Self Test diagnostics fail, replace the FRU that is indicated. If the tests
pass, but you still suspect a problem, run the ISL diagnostics and Mesa (Support Tools
Manager) online tests.
For a complete description of using ISL diagnostics and Mesa (Support Tools Manager),
refer to the following website URL:
http://wojo.rose.hp.com/
F low ch a r ts for Tr ou blesh ootin g
The following four figures contain troubleshooting flowcharts you can follow to isolate a
failing Field Replaceable Unit (FRU). Figure 3-1 contains the main (power on LCD)
troubleshooting flowchart. Figures 3-2 through 3-4 then contain flowcharts for console,
bootable device, and HP-UX troubleshooting, respectively.
42
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Flowcharts for Troubleshooting
Figu r e 3-1. Ma in (Pow er on LCD) Tr ou b lesh oot in g F low ch a r t
Chapter 3
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Flowcharts for Troubleshooting
Figu r e 3-2. Con sole Tr ou b lesh oot in g F low ch a r t
44
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Flowcharts for Troubleshooting
Figu r e 3-3. Boot a b le Device Tr ou b lesh oot in g F low ch a r t
Chapter 3
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Flowcharts for Troubleshooting
Figu r e 3-4. HP -UX Tr ou b lesh oot in g F low ch a r t
46
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Identifying LCD-Indicated Conditions
Id en tifyin g LCD-In d ica ted Con d ition s
The B2000 workstation uses an LCD panel to display firmware/OS progress codes. The
codes, referred to as chassis codes, consist of one of the mnemonics listed below, followed by
a 4-digit hexadecimal number identifying the code module being executed. The mnemonics
and their meanings are:
FLT
TST
INI
SHU
WRN
RUN
A hardware error has been detected
Hardware being tested
Hardware being initialized
System being shutdown
A non-optimal or unusual operating condition exists
Computer is running operating system
In general, the LCD display has the following format:
Line 1
Line 2
MMM CCCC: FFFFFF
DDDDDDDDDDDDDDDD
MMM
Three-character chassis code mnemonic
Four-digit hexadecimal code
CCCC
FFFFFF
Six-character Field Replaceable Unit (FRU) description
DDDDDDDDDDDDDDDD Description of the chassis code
If the system encounters an FLTcode while the system is booting, the FLTcode is
interpreted and a message is displayed. For example, you may have information similar to
the following in the LCD:
FLT
Three-character chassis code mnemonic
Four-digit hexadecimal code
30FC
SYS BD
Six-character Field Replaceable Unit (FRU) description
bad sys bd id Description of the chassis code
Chapter 3
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Fan Faults and Warnings
Fa n Fa u lts a n d Wa r n in gs
This section provides the fault (FLT) and warning (WRN) messages you will see in the LCD if
there is a problem with a fan in the B2000 workstation.
A chassis code which indicates that a fan has failed (FLT D01n) or is running too slowly
(WRN D02n) within a B2000 workstation specifies the fan number, n. Table 3-1 lists the fan
numbers and their names. To locate the correct fan, see Figure 3-5 on the next page.
Ta b le 3-1. Fa n Nu m b er s a n d Cor r esp on d in g Na m es
Fan Number (n) Name of the Fan
2
4
5
I/O fan
System fan
Processor fan
Here is an example of a fault message for the system fan (4):
FLT D014 SYS BD
fan 4: failure!
Here is an example of a warning message for the processor fan (5):
WRN D025 SYS BD
fan 5: too slow!
48
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Fan Faults and Warnings
Figu r e 3-5. Fa n Loca t ion s
I/O Fan (2)
System
Fan (4)
Processor
Fan (5)
In the case of a fan problem, you will need to replace:
•
•
The fan itself, if it is either an I/O fan (2) or a system fan (4).
The entire system board tray assembly, if it is a processor fan (5) (that is, the fan
mounted on the PA-RISC microprocessor on the system board).
See Chapter 4 for the procedures you should follow to remove and replace a fan.
Chapter 3
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Dealing with a Boot Failure
Dea lin g w ith a Boot Fa ilu r e
To start this workstation from an operating system stored on a device different from the
usual boot device, to boot from a different disk, or to boot from another type of device (such
as an alternate hard disk or CD), see the following situations and examples that use the
Boot Console Handler. To access the Boot Console Handler, see Chapter 6.
•
To boot from a known device containing a bootable operating system, type the following
at the prompt and press Enter:
Main Menu: Enter a command or a menu > boot device
where deviceis the hardware path to the device, specified in Mnemonic Style Notation
For example, to boot an operating system stored on a DDS-format tape in a drive
located at “scsi.1.0,” go to the Main Menu of the Boot Console Interface and then type
the following command at the prompt and press Enter:
Main Menu: Enter a command > boot scsi.1.0
The operating system on the specified device is used to start the workstation.
•
To interact with the Initial System Loader (ISL) before booting the workstation, type
the following at the prompt and press Enter:
Main Menu: Enter a command or a menu > boot device
You are prompted: Interact with ISL (Y or N) > y
Answering yes (y) causes the ISL to be loaded from the specified device. After a short
time, the following prompt appears on the screen:
ISL>
ISL is the program that actually controls the loading of the operating system. By
interacting with ISL, you can choose to load an alternate version of the HP-UX
operating system.
For example, if the usual kernel (/stand/vmunix for HP-UX 10.20) on the root disk
(scsi.6.0) has become corrupted, boot the workstation from the backup kernel
(/stand/vmunix.prev for HP-UX 10.20) by typing the following at the ISL> prompt
and press Enter:
ISL>hpux /stand/vmunix.prev
•
To find the location of the bootable operating systems on the various media in the file
system, use the searchiplcommand.
50
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Dealing with a Boot Failure
Sea r ch in g for Boota ble Med ia
To list all devices that may contain bootable media, go to the Main Menu of the Boot
Console Interface and then type the following at the prompt:
Main Menu: Enter a command or a menu > search ipl
The search may turn up more devices than there are lines on the display. If using a text
terminal, you can control the progress of the search from the terminal’s keyboard by
performing the following steps:
•
•
•
To hold the display temporarily, press Ctrl S
To continue the display, press Ctrl Q
To halt the search, press Esc
These flow-control commands do not work with a bitmapped display, but such a display can
show more than forty lines of text, so they are unnecessary.
To search for devices of just one type that actually contain bootable media, go to the Main
Menu of the Boot Console Interface and then type the following at the prompt:
Main Menu: Enter a command > search ipl device_type
where device_type is one of the following:
• scsiis the built-in fast, Ultra2 Wide LVD (Low Voltage Differential) SCSI bus.
• lanis all connections to the built-in LAN.
• ideis the built-in CD drive.
• pcinis an optional plug-in device in PCI slot number n.
• diskis any bootable device other than LAN.
Sta ble Stor a ge
Stable Storage is non-volatile memory associated with each PA-RISC processor module.
Stable storage is used by the processor (CPU) to store device path information, the state of
the boot flags, HPMC error information, and operating system initialization data.
Chapter 3
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Dealing with a Boot Failure
Boot Com m a n d Nota tion s
The bootcommand supports the following two notations:
•
•
Mnemonic
Path number
Type help scsior help lanfor more information on the boot path parameters.
Here are examples of mnemonic notation:
• bootwith no parameters selects the primary boot path in stable storage.
• boot with the alternate or alt parameter selects the alternate boot path in stable
storage.
Here is an example of path number notation:
• boot p1attempts to boot from the second path in a list generated by a previous search
command.
Su p p or ted Boot Pa th s
SCSI devices are bootable when connected to the SCSI port on the system. Diskless
workstations can only boot from the LAN port on the system board. The workstation can
be booted from the CD-ROM for software installation.
ISL En vir on m en t
The ISL environment provides the means to load the operating system (HP-UX)
environment. The ISL environment also provides an off-line platform to execute diagnostic
and utility programs from a boot device when HP-UX does not load.
The ISL program is the first program loaded into main memory from an external media
(LAN, disk, or tape) and launched by the initial program loader (IPL) routine during the
Boot Administration environment.
The ISL environment provides the following capabilities:
•
Execute user-entered commands to modify boot device paths and boot options in stable
storage.
•
•
Run off-line diagnostic programs and utilities.
Provide automatic booting of the HP-UX operating system after power-on or reset.
The ISL program provides a stand-alone environment for loading off-line diagnostic and
utility programs from the LIF directory. The ISL program also provides user commands to
configure the boot parameters into Stable Storage.
52
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Selftest Fa ilu r es
Chassis codes are the key to debugging selftest errors. If a failure is found during selftest,
chassis codes are displayed in the LCD. The procedure for using these codes to debug a
failure is as follows:
1. Using Table 3-2, which starts on the next page, find the chassis code listed on the LCD.
2. To get additional information about failures from the Boot Console Handler, use the
Service Menu’s pim, pdt, and ChassisCodescommands.
In the following table, the FRU column shows messages printed on the LCD that refer to
system FRUs. Only FLTcodes have FRUs associated with them. Some WRNcodes are also
device specific, especially to IODC calls; for example, 8xxxcodes. TSTand INIcodes do not
necessarily correspond to any FRU. All codes are listed in numeric order.
NOTE
Because the B2000 workstation is a single-board system, references to the
I/O BD(I/O board) in chassis codes displayed on the LCD and listed in Table
3-2 are actually references to the SYS BD(system board).
Chapter 3
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ch a ssis Cod es
Table 3-2. lists all of the chassis codes for the B2000 workstation.
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
FLT
1n01 SYS BD HPMC occurred
CPU n detected an unexpected HPMC.
1n02 SYS BD powerfail intrpt CPU n detected an unexpected power fail
interrupt.
FLT
FLT
1n03 SYS BD recvry cntr trap CPU n detected an unexpected recovery
counter trap.
1n04 SYS BD external intrrpt CPU n detected an unexpected external
interrupt.
FLT
FLT
1n05 SYS BD LPMC occurred
CPU n detected an unexpected LPMC.
1n06 SYS BD ITLB mis/Ipg flt CPU n detected an unexpected ITLB miss
or instruction page fault.
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
1n07 SYS BD I mem prot trap
CPU n detected an unexpected instruction
memory protection trap.
1n08 SYS BD illegal inst trp CPU n detected an unexpected illegal
instruction trap.
1n09 SYS BD break instr trap CPU n detected an unexpected break
instruction trap.
1n0A SYS BD privilgd op trap CPU n detected an unexpected privileged
operation trap.
1n0B SYS BD privlgd reg trap CPU n detected an unexpected privileged
register trap.
1n0C SYS BD overflow trap
CPU n detected an unexpected overflow
trap.
1n0D SYS BD conditional trap CPU n detected an unexpected conditional
trap.
1n0E SYS BD assist exep trap CPU n detected an unexpected assist
exception trap.
1n0F SYS BD DTLB mis/Dpg flt CPU n detected an unexpected DTLB
miss or data page fault.
1n10 SYS BD non-acc ITLB mis CPU n detected an unexpected non-access
ITLB miss fault.
1n11 SYS BD non-acc DTLB mis CPU n detected an unexpected non-access
DTLB miss or data page fault.
1n12 SYS BD data mem prot tr CPU n detected an unexpected data
memory protection trap.
54
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
1n13 SYS BD data mem brk trp CPU n detected an unexpected data
memory break trap.
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
TST
TST
TST
TST
TST
TST
TST
1n14 SYS BD TLB dirty bit tr CPU n detected an unexpected TLB dirty
bit trap.
1n15 SYS BD page refrnce trp CPU n detected an unexpected page
reference trap.
1n16 SYS BD assist emul trap CPU n detected an unexpected assist
emulation trap.
1n17 SYS BD hi-priv xfer trp CPU n detected an unexpected
higher-privilege transfer trap.
1n18 SYS BD lo-priv xfer trp CPU n detected an unexpected
lower-privilege transfer trap.
1n19 SYS BD taken branch trp CPU n detected an unexpected
taken-branch trap.
1n1A SYS BD data mem acc rts CPU n detected an unexpected data
memory access rights trap.
1n1B SYS BD data mem prot ID CPU n detected an unexpected data
memory protection ID trap.
1n1C SYS BD unalign data ref CPU n detected an unexpected unaligned
data reference trap.
1n1D SYS BD perf mon intrrpt CPU n detected an unexpected
performance monitor interrupt.
1n20 SYS BD CPUn basic test
1n21 SYS BD CPUn alu test
CPU n is starting its basic operations
self-test.
CPU n is starting its arithmetic and
logical unit self-test.
1n22 SYS BD CPUn branch test CPU n is starting its branch instruction
self-test.
1n23 SYS BD CPUn arith cond
1n24 SYS BD CPUn bit opers
1n25 SYS BD CPUn cntrl regs
1n26 SYS BD CPUn ext intrpt
CPU n is starting its arthimetic condition
self-test.
CPU n is starting its bit operation
instruction self-test.
CPU n is starting its control register
self-test.
CPU n is starting its external interrupt
self-test.
Chapter 3
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
TST
1n27 SYS BD CPUn itimer test CPU n is starting its interval timer
self-test.
TST
TST
TST
TST
TST
TST
WRN
FLT
1n28 SYS BD CPUn multi-media CPU n is starting its multi-media
instructions self-test.
1n29 SYS BD CPUn shadow reg
CPU n is starting its shadow register
self-test.
1n2A SYS BD CPUn diagnse reg CPU n is starting its diagnose register
self-test.
1n2B SYS BD CPUn rdr test
CPU n is starting its remote diagnose
register self-test.
1n2C SYS BD CPUn bypass test CPU n is starting its integer bypass
operation self-test.
1n30 SYS BD CPUn start est
1n31 SYS BD CPUn skip est
CPU n is starting its early (pre-memory)
self-tests.
CPU n is bypassing its early self-tests to
save time.
1n32 SYS BD CPUn bad tst mod CPU n detected an unsupported system
mode.
INI
TST
TST
1n3C SYS BD CPUn initialize
1n3E SYS BD CPUn exit est
1nA0 SYS BD CPUn fpu tests
CPU n is initializing after self-tests.
CPU n finished its early self-tests.
CPU n is starting its floating-point unit
self-tests.
TST
TST
TST
TST
TST
TST
TST
1nA1 SYS BD CPUn fpu reg tst CPU n is starting its floating-point
register self-test.
1nA2 SYS BD CPUn fpu inst
1nA3 SYS BD CPUn fpu traps
1nA4 SYS BD CPUn fpu misc
1nA5 SYS BD CPUn fpu bypass
CPU n is starting its floating-point
instruction self-test.
CPU n is starting its floating-point trap
self-test.
CPU n is starting its floating-point
miscellaneous operations self-test.
CPU n is starting its floating-point
bypassing self-test.
1nB1 SYS BD CPUn TLB RAM tst CPU n is starting its TLB register
self-test.
1nB2 SYS BD CPUn TLB trans
CPU n is starting its TLB translation
self-test.
56
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
FLT
FLT
INI
1nBA SYS BD monarch CPU fail The monarch CPU failed.
1nBB SYS BD bad CPUn number
1nBF SYS BD CPUn halt boot
The CPU identifier was out of range.
Bootstrap failure--machine halted.
1nCA SYS BD CPUn sys bus arb Monarch CPU is initializing the system
bus arbitration.
WRN
WRN
FLT
WRN
1nCD SYS BD CPUn deconfig
1nCE SYS BD CPUn extinguish
1nCF SYS BD slaven failed
1mDs SYS BD slaves deconfig
CPU n deconfigured itself.
PDC_PROC halted CPU n.
Slave CPU n failed self-test.
Monarch CPU m deconfigured slave CPU
s.
WRN
1nEF SYS BD CPUn slftst warn CPU n detected a non-fatal error during
its self-tests.
WRN
INI
1mFs SYS BD monm stop slaves Monarch CPU m halted slave CPU s.
1nFC SYS BD CPUn sync’ing
CPU n is synchronizing with the rest of
the system.
INI
FLT
TST
1nFD SYS BD CPUn stat wd tst CPU n is testing the system status word.
1nFF SYS BD monarchn selftst Monarch CPU n failed self-test.
2n20 SYS BD CPUn icache RAM
CPU n is starting its instruction cache
RAM self-test.
FLT
FLT
TST
TST
TST
FLT
TST
TST
2n25 SYS BD CPUn ic ld d err CPU n detected a data error during data
cache load.
2n26 SYS BD CPUn ic ld t err CPU n detected a tag error during data
cache load.
2n30 SYS BD CPUn icache tag
2n40 SYS BD CPUn icache par
CPU n is starting its instruction cache tag
self-test.
CPU n is starting its instruction cache
parity detection self-test.
2n50 SYS BD CPUn dc stor que CPU n is starting its data cache store
queue self-test.
2n51 SYS BD CPUn dc st q err CPU n detected an error during its data
cache store queue self-test.
2n70 SYS BD CPUn dcache RAM
2n80 SYS BD CPUn dcache tag
CPU n is starting its data cache RAM
self-test.
CPU n is starting its data cache tag
self-test.
Chapter 3
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
TST
2n90 SYS BD CPUn dcache ECC
CPU n is starting its data cache ECC
self-test.
FLT
TST
2BAD SYS BD assertion fail
A firmware assertion failed.
3n00 SYS BD ROM checksum tst Monarch CPU n is testing the boot ROM
integrity.
FLT
INI
TST
3n00 SYS BD ROM checksum BAD The boot ROM failed checksum.
3n00 SYS BD ROM checksum ok
The boot ROM passed checksum.
3n01 SYS BD PDH control test Monarch CPU n is testing PDH control
register.
INI
FLT
3n01 SYS BD PDH control init Monarch CPU n is initializing the PDH
control register.
3n01 SYS BD PDH control err
Monarch CPU n detected an error in the
PDH control register.
TST
INI
FLT
WRN
3n02 SYS BD scratch RAM test Monarch CPU n is testing scratch RAM.
3n02 SYS BD scratch RAM ok
3n02 SYS BD scratch RAM bad
The scratch RAM test failed.
The scratch RAM test passed.
3n03 SYS BD stbl st read err CPU n detected a non-fatal error reading
the stable store.
FLT
3n03 SYS BD stbl st read err CPU n detected a non-fatal error reading
the stable store.
INI
INI
3nC4 SYS BD clearing EEPROM
Monarch CPU n is clearing the EEPROM.
3nD4 SYS BD deflting EEPROM2 Monarch CPU n is initializing the
EEPROM to system defaults.
WRN
FLT
FLT
WRN
FLT
INI
3n04 SYS BD EEPROM write err CPU n detected a non-fatal error writing
the EEPROM.
3n04 SYS BD EEPROM write err CPU n detected a fatal error writing the
EEPROM.
3n05 SYS BD EEPROM wrt limit CPU n detected a fatal error writing the
EEPROM.
3n06 SYS BD EEPROM read err
3n06 SYS BD EEPROM read err
CPU n detected a non-fatal error reading
the EEPROM.
CPU n detected a fatal error reading the
EEPROM.
3n07 SYS BD
CPUninvoke LDB
CPU n is starting the low-level debugger.
58
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
3n09 SYS BD bad sys mde byte CPU n detected an unsupported system
mode.
WRN
TST
WRN
FLT
3n1A SYS BD hversion mismtch Stable store hardware version doesn’t
match system.
3n1B SYS BD chck model strng Check model string with version in stable
store.
3n1B SYS BD model str msmtch Model string doesn’t match that in stable
store.
3n1B SYS BD fatal model str
Error reading model string from stable
store.
TST
WRN
FLT
INI
3n1C SYS BD test software ID Check LANIC address.
3n1C SYS BD update sw ID Update LANIC address.
3n1C SYS BD update sw ID err Error updating LANIC address.
3n2s SYS BD Invoke LDB: s
CPU n is awaiting the low-level debugger
for s more seconds.
TST
3nBC IO BD
test sys clocks
CPU n is verifying processor clocks with
the real-time clock.
INI
FLT
3nBC SYS BD init sys clocks
CPU n has initialized the processor clocks.
3nBC IO BD
RTC tick timeout The real-time clock is ticking too slowly or
not at all.
FLT
TST
INI
FLT
FLT
FLT
3nCD IO BD
RTC tick timeout The real time clock is ticking too slowly or
not at all.
3nCD SYS BD check defaults
3nCD SYS BD init defaults
3nCD SYS BD init EEPROM err
3nEC SYS BD bad sys config
CPU n is initializing stable store values to
system defaults.
CPU n finished initializing stable store
values.
CPU n detected an error writing to stable
store.
CPU n detected an illegal CPU board
configuration.
3nF4 SYS BD EEPROM boot limt CPU n detected a fatal error writing the
EEPROM.
FLT
TST
3nFC SYS BD bad sys bd id
4n00 SYS BD CPUn start lst
CPU n cannot identify CPU board.
CPU n is starting its late (with memory)
self-tests.
Chapter 3
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
WRN
4n01 SYS BD CPUn skip lst
CPU n is bypassing its late self-tests to
save time.
TST
TST
4n0E SYS BD CPUn exit lst
CPU n finished its late self-tests.
4n20 SYS BD CPUn lst erly st CPU n is re-executing some of its early
self-tests from system memory.
TST
TST
TST
TST
TST
TST
TST
TST
TST
TST
TST
TST
TST
TST
4n21 SYS BD CPUn lst basic
4n22 SYS BD CPUn lst alu
4n23 SYS BD CPUn lst branch
CPU n is re-executing its basic operations
self-test.
CPU n is re-executing its arithmetic and
logic unit self-test.
CPU n is re-executing its branch
instruction self-test.
4n24 SYS BD CPUn lst arth cd CPU n is re-executing its arithmetic
conditions self-test.
4n25 SYS BD CPUn lst bit ops CPU n is re-executing its bit operations
self-test.
4n26 SYS BD CPUn lst ctl reg CPU n is re-executing its control register
self-test.
4n27 SYS BD CPUn lst ext int CPU n is re-executing its external
interrupt self-test.
4n28 SYS BD CPUn lst itimer
CPU n is re-executing its interval timer
self-test.
4n29 SYS BD CPUn lst mltimed CPU n is re-executing its multi-media
instructions self-test.
4n2A SYS BD CPUn lst shadow
CPU n is re-executing its shadow register
self-test.
4n2B SYS BD CPUn lst dg regs CPU n is re-executing its diagnose
register self-test.
4n2C SYS BD CPUn lst rdrs
4n2D SYS BD CPUn lst bypass
4n30 SYS BD CPUn cache byte
CPU n is re-executing its remote diagnose
register self-test.
CPU n is re-executing its integer bypass
operation self-test.
CPU n is starting its data cache sub-word
operations self-test.
TST
TST
4n40 SYS BD CPUn cache flush CPU n is starting its cache flush self-test.
4n50 SYS BD CPUn icache miss CPU n is starting its instruction cache
miss self-test.
60
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
TST
4n60 SYS BD CPUn dcache miss CPU n is starting its data cache miss
self-test.
FLT
FLT
FLT
FLT
FLT
FLT
FLT
5n00 SYS BD unknown bus err
CPU n detected an unknown error on the
system bus (Runway).
5n02 SYS BD path err assertd CPU n detected a path error on the
system bus (Runway).
5n04 SYS BD parity error
CPU n detected a data, address, or control
parity error on the system bus (Runway).
5n07 SYS BD Runway dir error CPU n detected a directed error on the
system bus (Runway).
5n08 SYS BD Runway broad err CPU n detected a broadcast error on the
system bus (Runway).
5n0A SYS BD illegal response CPU n received data that did not match
any outstanding data request.
5n0B SYS BD bus timeout
CPU n timed out before receiving
requested data. The responder is logged in
the system responder address.
FLT
5n0C SYS BD CPU sync failure CPU n’s synchronizer detected a rule
violation on the system bus (Runway).
INI
INI
FLT
FLT
TST
WRN
FLT
7000 DIMM
start DIMM scan
Start looking for installed DIMMs.
Initialize memory data structures.
7002 SYS BD init mem tables
7004 SYS BD mem plt upd fail Error updating memory platform data.
7005 DIMM
7010 DIMM
7011 DIMM
7012 DIMM
insufficient mem Insufficient memory detected to continue.
check DIMM order Start memory DIMM order check.
skip DIMM ord ck Bypass memory DIMM order check.
DIMM order error Memory DIMMs are not in the proper
order.
FLT
7013 DIMM
DIMM order error Memory DIMMs are not in the proper
order. As a result, the system cannot
access one or more DIMMs and has
deallocated all inaccessible DIMMs.
TST
7016 DIMM
DIMM pair check
Start memory DIMM pair check (DIMMs
in a pair (e.g. 0a/0b) must match in
J 7000).
WRN
FLT
7017 DIMM
701F DIMM
skip mem pair ck Bypass memory DIMM set check.
no memory found Memory scan couldn’t find any DIMMs.
Chapter 3
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
TST
7020 SYS BD search for IMM
Try to find a single memory bank to use
for the initial memory module.
TST
FLT
TST
703s DIMM
704s DIMM
705s DIMM
DIMM s IMM vrfy
DIMM s IMM fail
DIMM s IMM test
DIMM s was the initial memory module
last boot. Verify it still works.
DIMM s failed the initial memory module
test.
Test DIMM in slot s as the initial memory
module.
INI
INI
TST
706s DIMM
DIMM s is IMM
DIMM scan done
DIMM s chosen as initial memory module.
70F0 DIMM
Memory DIMM scan complete.
7100 SYS BD mem register tst Start testing registers in memory
controller.
WRN
FLT
FLT
FLT
FLT
FLT
INI
7101 SYS BD skip mem reg tst Bypass the memory controller register
test.
7102 SYS BD mem addr reg tst Firmware detected an error in the
memory controller address registers.
7103 SYS BD mem mbat reg tst Firmware detected an error in the
memory controller bank registers.
7104 SYS BD mem reg tst fail Firmware detected an error in the
memory controller memory registers.
7105 SYS BD mem err reg test Firmware detected an error in the
memory controller error registers.
7106 SYS BD mem err clr fail Firmware was unable to clear the error
registers after testing.
7200 DIMM
strt DIMM detect Start the Serial Presence Detection (SPD)
to search for memory DIMMs.
INI
WRN
FLT
FLT
INI
7201 DIMM
DIMM detect x%
SPD is x% finished.
7202 SYS BD skip DIMM detect Bypass Serial Presence Detection.
7203 DIMM
7204 DIMM
7205 DIMM
unsupp DIMM type SPD found an unsupported DIMM type.
SPD fatal error SPD detected an unexpected, fatal error.
add HP DIMM type New HP manufactured DIMM type added
to tables.
INI
7206 DIMM
non-HP DIMM type New non-HP DIMM type added to tables
(use at own risk).
62
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
7207 DIMM
DIMM table full
The DIMM table is full--cannot add new
type.
FLT
INI
INI
7208 DIMM
721s DIMM
722s DIMM
no DIMMs found
is DIMM s inst?
???? DIMM in s
SPD didn’t find any memory DIMMs.
SPD is checking memory slot s.
SPD found a DIMM in slot s, but can’t
determine its size. DIMM will not be used.
INI
INI
INI
FLT
723s DIMM
724s DIMM
725s DIMM
72As DIMM
128M DIMM in s
256M DIMM in s
512M DIMM in s
DIMM s checksum
SPD found a 128MB DIMM in slot s.
SPD found a 256MB DIMM in slot s.
SPD found a 512MB DIMM in slot s.
DIMM in slot s failed SPD checksum and
will not be used.
FLT
FLT
72Cs DIMM
72Ds DIMM
DIMM s mismatch
DIMM s load err
DIMM in slot s didn’t match the other in
pair. (J 7000 only--DIMMs must be in
matched pairs.)
Memory DIMMs are not in the proper
order. As a result, the system cannot
access DIMM s and has deallocated it.
INI
TST
7300 SYS BD mem config start Starting main memory configuration.
7301 SYS BD check mem config Checking for memory configuration
change since last boot.
WRN
INI
7302 SYS BD mem confg changd Memory physical configuration changed
since last boot.
7303 SYS BD use confg change Memory physical configuration didn’t use
saved configuration change. Use stored
configuration data.
INI
INI
WRN
7304 SYS BD build mem intrlv Building memory configuration with all
DIMMs interleaved.
7305 SYS BD save mem config
Saving memory configuration information
in non-volatile memory.
7306 SYS BD use alt mem conf Memory will be configured from fixed
values, instead of detected DIMMs.
INI
FLT
7307 SYS BD interleve memory Generating the memory interleave.
7308 SYS BD PDT is disabled
Firmware detected bad memory pages,
but the Page Deallocation Table is
disabled.
Chapter 3
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
7309 DIMM
insufficient mem Insufficient error-free memory to
continue.
FLT
INI
TST
TST
INI
WRN
FLT
730C SYS BD mem intrlv fail
730F SYS BD mem config done
Memory interleave generation failed.
Main memory configuration complete.
7400 DIMM
740F DIMM
non-dest mem tst Starting non-destructive memory test.
non-dst tst done Non-destructive memory test complete.
7500 SYS BD memory reset
Resetting memory system.
7501 SYS BD mem log clr warn Memory error logs didn’t clear on first try.
7502 SYS BD mem err log fail Firmware could not clear memory error
logs.
TST
WRN
7600 DIMM
7601 DIMM
dest mem test
mem init only
Starting the destructive memory test.
Skip the test, just initialize memory to
save time.
TST
TST
TST
7602 DIMM
7603 DIMM
7604 DIMM
tst 1st mem page Starting 3-pass test of first memory page.
tst rest of mem
start 1st pass
Starting 3-pass test of the rest of memory.
Starting 1st pass of memory test (write
pseudorandom sequence).
TST
TST
7605 DIMM
7606 DIMM
1st pass x%
First pass is x% complete.
start 2nd pass
Starting 2nd pass of memory test (verify
pseudorandom sequence, write inverse).
TST
TST
7607 DIMM
7608 DIMM
2nd pass x%
Second pass is x% complete.
start 3rd pass
Starting 3rd pass of memory test (verify
inverse sequence).
TST
TST
7609 DIMM
760A DIMM
3rd pass x%
Third pass is x% complete.
start mem init
Starting memory initialization. (Initialize
to zero to set ECC.)
TST
WRN
760B DIMM
760C DIMM
mem init x%
Memory initialization is x% complete.
repeat dest test Re-execute destructive test for hardware
troubleshooting.
FLT
FLT
760D DIMM
7610 DIMM
mem code cpy err Firmware tried to copy code from ROM to
memory, but the copy didn’t match the
original.
ECC wrt/read err Writing and reading back good data
caused memory ECC error.
64
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
7611 DIMM
7612 DIMM
7613 DIMM
7614 DIMM
ECC single data
Memory ECC test failed to detect
single-bit data error.
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
FLT
ECC single ECC
Memory ECC test failed to detect
single-bit ECC error.
ECC multipl data Memory ECC test failed to detect
multiple-bit data error.
ECC multpl signl Memory ECC test failed to signal
multiple-bit error.
7800 SYS BD mem err summary
Printing memory error summary word to
RS-232.
7801 SYS BD bus ctrl par err System bus (Runway) control parity error
detected.
7802 SYS BD bus addr par err System bus (Runway) address parity error
detected.
7803 SYS BD bus data par err System bus (Runway) data parity error
detected.
7804 SYS BD mem out of range Memory access outside configured
memory space.
7805 SYS BD bus broadcst err System bus (Runway) broadcast error
detected.
7806 SYS BD mem addr par err Memory bus address parity error
detected.
7807 SYS BD mem ctlr stat wd Printing memory controller status word to
RS-232.
781s SYS BD DIMM s uncor err
782s SYS BD DIMM s corr err
7840 SYS BD unexpected HPMC
Uncorrectable ECC error detected in
DIMM s.
Correctable ECC error detected in DIMM
s.
FLT
FLT
FLT
FLT
FLT
Unexpected HPMC detected.
7841 SYS BD mem status invld Memory error status word is invalid.
7842 SYS BD mem summ invalid Memory summary word is invalid.
7843 SYS BD fwd prog invalid Memory forward progress word is invalid.
7844 SYS BD mem HPMC summ wd Printing memory error summary word to
RS-232.
FLT
7845 SYS BD mem ctlr stat wd Printing memory controller status word to
RS-232.
Chapter 3
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
FLT
7846 SYS BD mem err overflow Multiple memory errors detected.
7848 SYS BD addr not mapped
Memory address outside configured
memory space.
FLT
FLT
785s DIMM
786s DIMM
MBE in DIMM s
SBE&MBE DIMM s
Destructive memory test detected an
uncorrectable memory error in DIMM s.
Destructive memory test detected both an
uncorrectable and a correctable memory
error in DIMM s.
FLT
FLT
FLT
787s DIMM
788s DIMM
7890 DIMM
mem err DIMM s
SBE in DIMM s
MBE overwrt SBE
Destructive memory test detected a
pattern compare error in DIMM s.
Destructive memory test detected a
correctable memory error in DIMM s.
Firmware replaced a correctable memory
error entry in the PDT with an
uncorrectable memory error entry at the
same address.
FLT
7891 DIMM
dup entry in PDT The PDT already contains an entry at
that address.
FLT
FLT
FLT
FLT
FLT
FLT
FLT
7892 SYS BD PDT write error
7893 SYS BD PDT is full
7900 SYS BD no DMT entry
7901 SYS BD no rank entry
Error adding the entry to the PDT.
The PDT is full--cannot add new entry.
Internal error--cannot find DIMM entry.
Internal error--cannot find rank entry.
7902 SYS BD bad refrsh intvl Computed refresh interval is invalid.
7903 SYS BD mem intrlv fail Cannot generate memory interleave.
7904 SYS BD mem reloc failed Cannot interleave with relocated range
(3.75GB - 4.0GB).
FLT
FLT
7905 SYS BD mem intrlv error Undefined memory interleave failure.
79FF SYS BD mem firmware err Internal error--never expected this to
happen.
WRN
WRN
80F3 SYS BD err rd IODC byte Cannot read IODC from ROM or card.
80F4 EXT IO boot read error
Cannot load IODC entry_init for boot
device.
WRN
WRN
80F5 EXT IO boot exec error
80F6 EXT IO boot read error
Error initializing boot device.
Cannot load IODC entry_io for boot
device.
66
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
Error detected during boot device I/O.
WRN
WRN
WRN
INI
INI
80F7 EXT IO boot IO error
80F8 EXT IO invalid boot dev Invalid boot device class; bad IODC?
80FC EXT IO invalid boot dev Unexpected error; bad IODC?
8800 IOCARD PCI BusWlk start Starting PCI bus and device discovery.
88r1 IOCARD PCI Rope r walk
Starting PCI bus and device discovery on
Rope r.
INI
INI
8802 IOCARD PCI BusWalk done PCI bus and device discovery complete.
8803 SYS BD PCI alloc done
Done allocating address space for PCI
devices.
INI
WRN
FLT
WRN
FLT
WRN
8804 SYS BD PCI config done
Done configuring PCI devices.
881r IO BD
881r IO BD
882r IO BD
882r IO BD
883r IO BD
R2PCIr not found Rope-to-PCI bridge r not found.
R2PCIr not found Rope-to-PCI bridge r not found.
R2PCIr not found Rope-to-PCI bridge r initialization failed.
Roper init err
Rope-to-PCI bridge r initialization failed.
Roper config err PCI configuration failed below
Rope-to-PCI bridge r.
FLT
INI
FLT
INI
883r IO BD
Roper config err Rope r configuration failed.
884r EXT IO Roper debug tggl Rope r debug register toggled.
884r EXT IO Roper tgl fail Rope r debug register toggle failed.
8850 SYS BD early rope0 init Initializing rope 0 for early RS-232
output.
FLT
INI
INI
8850 SYS BD rope0 init fail
8860 SYS BD rope0 init done
Couldn’t initialize rope 0.
Rope 0 initialization complete.
8870 IO BD
early R2PCI init Initializing Rope-to-PCI bridge 0 for early
RS-232 output.
FLT
INI
8870 IO BD
8880 IO BD
R2PCI init fail
R2PCI init done
Couldn’t initialize Rope-to-PCI bridge 0.
Rope-to-PCI bridge 0 initialization
complete.
INI
8890 IO BD
early Super init Initializing Super-I/O for early RS-232
output.
FLT
INI
8890 IO BD
88A0 IO BD
Super init fail
Super init done
Couldn’t initialize Super-I/O.
Super-I/O initialization complete.
Chapter 3
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
WRN
8A03 EXT IO No graph console Cannot re-establish communications with
the graphics console.
WRN
8A04 EXT IO No USB keyboard
Cannot re-establish communications with
the USB keyboard.
TST
WRN
WRN
WRN
WRN
8C06 EXT IO PCI BIST test
8C07 EXT IO PCI BIST error
8C08 SYS BD PCI alloc error
Running PCI Built-In Self-Test
PCI Built-In Self-Test failed.
PCI address space allocation failed.
8C09 IO BD
PCI mem mngr err Memory allocation for PCI device failed.
8C0A EXT IO PCI mem type err PCI device requested invalid memory
type.
WRN
8C0B IO BD
PCI max bus dpth PCI bus depth exceeded maximum
supported depth.
WRN
WRN
WRN
SHU
8C0C EXT IO PCI dev not cnfg Unable to configure PCI device.
8C0F IO BD
8DEC IO BD
8DEC IO BD
dev tree ovrflow Data space for PCI devices is full.
init LAN SROM Initializing the core LAN serial EPROM.
resetting system Restarting system after core LAN
initialization.
FLT
FLT
FLT
FLT
FLT
WRN
INI
8E10 IO BD
8E11 IO BD
8E12 IO BD
8E13 IO BD
8E20 IO BD
PARALEL port cfg Parallel port configuration failed.
SERIAL1 port cfg Serial 1 port configuration failed.
SERIAL2 port cfg Serial 2 port configuration failed.
FLOPPY drive cfg Floppy drive configuration failed.
bad USB port cfg USB port configuration failed.
9001 EXT IO no console found Search for console display device failed.
9151 IO BD
9152 IO BD
915F IO BD
init SERIAL_1
Initializing serial 1 port as console
display.
INI
INI
INI
INI
init SERIAL_2
Initializing serial 2 port as console
display.
init unknown dev Initializing unknown device as console
display.
9160 EXT IO builtin GRAPHICS Initializing built-in graphics as console
display.
916s EXT IO init PCI slot s
Initializing PCI device in slot s as console
display.
68
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
INI
91DB IO BD
init SERIAL_LDB
Initializing serial LDB port as console
display.
INI
WRN
9C51 IO BD
9C51 IO BD
consol is SER_1
Console display is on serial port 1.
bad init SERIAL1 Serial port 1 failed to initialize as a
console device.
INI
WRN
9C52 IO BD
9C52 IO BD
consol is SER_2
Console display is on serial port 2.
bad init SERIAL2 Serial port 2 failed to initialize as a
console device.
INI
WRN
INI
WRN
9C6s EXT IO consol is GRAPHs Console display is on graphics card in PCI
slot s.
9C6s EXT IO bad PCI slot s
9C8t EXT IO cnfg mon type t
9C8t EXT IO mon type t fail
Graphics in PCI slot s failed to initialize
as a console device.
Set graphics console to monitor type t.
(Seen when cycling through types.)
Failed to configure console to monitor type
t.
INI
WRN
9CDB IO BD
9CDB IO BD
consl is SER_LDB Console display is on serial LDB port.
bad init SER_LDB Serial LDB port failed to initialize as a
console device.
FLT
WRN
WRN
A088 IO BD
consl path fault Unable to boot--no console device found.
A008 EXT IO no boot device
Unable to boot--no bootable device found.
A0BD EXT IO device not ready Boot device not ready--operation may be
retried.
FLT
A0FF EXT IO unknown launch
Unable to boot. Explanation may appear
on console.
WRN
WRN
A50F EXT IO init pri pth err Unable to boot from primary boot device.
A70F EXT IO init otr pth err Unable to boot from non-primary boot
device.
INI
INI
INI
C10m SYS BD CPUm is monarch
C30m SYS BD monarchm test
C30C SYS BD mnrch slv chck
CPU m was chosen as the monarch
processor. (All other CPUs are slaves.)
CPU m finished the monarch-only tests
and system initialization.
The monarch CPU is checking whether
the slaves are in the correct rendezvous.
Chapter 3
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
INI
C3FF SYS/IO late monarch tst The monarch CPU is starting the late
(post-memory) monarch-only tests.
FLT
C3FF SYS/IO late monarch flt The late (post-memory) monarch-only
tests failed.
INI
INI
INI
INI
INI
C4CC SYS BD initialize ccp
C4CD SYS BD no ccp found
C4CE SYS BD ccp disabled
C4CF SYS BD ccp found
Searching for (lab-only) debugger card.
Debugger card not found.
Debugger card disabled.
Debugger card found.
C500 SYS BD get primary path Autoboot is reading primary boot path
from stable store.
INI
C540 EXT IO init pri path
Autoboot is trying to boot from primary
boot device.
INI
WRN
C580 EXT IO load IPL pri pth Loading IPL from primary boot device.
C5F0 EXT IO err read pri IPL Error loading IPL from primary boot
device.
FLT
WRN
WRN
WRN
WRN
WRN
C5F0 EXT IO pri IPL fault
Error loading IPL from primary boot
device.
C5F1 EXT IO err read pri IPL Cannot load IPL from primary boot
device--load address invalid.
C5F2 EXT IO err read pri IPL Cannot load IPL from primary boot
device--file is not IPL image.
C5F3 EXT IO err read pri IPL Cannot load IPL from primary boot
device--IPL image size invalid.
C5F4 EXT IO err read pri IPL Cannot load IPL from primary boot
device--IPL entry point address invalid.
C5F8 EXT IO err read pri IPL Cannot load IPL from primary boot
device--IPL image checksum failed.
INI
INI
FLT
C5FF
<blank> launch pri IPL
Booting from primary boot path.
C642 EXT IO init kybrd consl Try to initialize USB keyboard.
C642 EXT IO keyboard error
C643 EXT IO keyboard reinit
An error was detected trying to access the
keyboard.
WRN
WRN
Keyboard was re-initialized.
C64F EXT IO reset montr type The console device failed to initialize with
the given monitor type. Try again with
type 1.
70
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
TST
INI
C680 SYS BD builtin graphics Look for built-in graphics card.
C680 SYS BD builtin graphics Successfully initialized built-in graphics
card.
WRN
TST
INI
C680 SYS BD builtin graphics Built-in graphics initialization failed.
C68s SYS BD test graph in s
C68s SYS BD init graph in s
Look for graphics card in PCI slot s.
Successfully initialized graphics card in
PCI slot s.
WRN
INI
INI
WRN
WRN
WRN
WRN
WRN
WRN
WRN
INI
WRN
C68s SYS BD fail graph in s
Card in PCI slot s failed graphics
initialization or is not a graphics card.
C740 EXT IO init other path
Autoboot is trying to boot from
non-primary boot device.
C780 EXT IO ld IPL othr path Loading IPL from non-primary boot
device.
C7F0 EXT IO other IPL fault
Error loading IPL from non-primary boot
device.
C7F1 EXT IO bad alt IPL read Cannot load IPL from non-primary boot
device--load address invalid.
C7F2 EXT IO bad alt IPL read Cannot load IPL from non-primary boot
device--file is not IPL image.
C7F3 EXT IO bad alt IPL read Cannot load IPL from non-primary boot
device--IPL image size invalid.
C7F4 EXT IO bad alt IPL read Cannot load IPL from non-primary boot
device--IPL entry point address invalid.
C7F8 EXT IO bad alt IPL read Cannot load IPL from non-primary boot
device--IPL image checksum failed.
C7FF
<blank> launch IPL other Booting from a device other than the
primary boot path.
CB00 SYS BD TOC initiated
A Transfer of Control entered the
firmware TOC handler.
CB01 SYS BD no OS TOC vector There is no TOC vector for the operating
system. Firmware will soft boot the
system.
WRN
CB02 SYS BD bad OS TOC addr
The operating system TOC handler vector
is invalid. Firmware will soft boot the
system.
Chapter 3
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
WRN
CB03 SYS BD bad OS TOC code
The operating system TOC handler is
invalid. Firmware will soft boot the
system.
WRN
WRN
WRN
CB04 SYS BD bad OS TOC len
The size of the operating system TOC
handler is invalid. Firmware will soft boot
the system.
CB05 SYS BD bad OS TOC chksm The operating system TOC handler failed
the checksum test. Firmware will soft boot
the system.
CB0A SYS BD prev TOC logged
Firmware detected unread PIM data from
a previous TOC and will not overwrite it.
(PIM for this TOC is lost.)
INI
WRN
CB0B SYS BD branch to OS TOC Branching to the operating system TOC
handler.
CB0C SYS BD br OS TOC failed Branch to the operating system TOC
handler failed. Firmware will soft boot the
system.
WRN
CB10 SYS BD LPMC initiated
A Low-Priority Machine Check entered
the firmware LPMC handler. The handler
should log the error and return to normal
operation.
WRN
WRN
WRN
WRN
FLT
CB11 SYS BD icache LPMC err
CB12 SYS BD dcache LPMC err
An instruction cache parity error caused
the LPMC.
A data cache parity/ECC error caused the
LPMC.
CB13 SYS BD dcache tag error The parity error is in the tag portion of
the data cache.
CB14 SYS BD dcache data err
CB1F SYS BD OS LPMC failed
The parity error is in the data portion of
the data cache.
Firmware couldn’t branch to the operating
system LPMC handler. It will halt the
CPU, requiring a power cycle to recover.
WRN
WRN
CB71 SYS BD HPMC occurred
CB72 SYS BD LPMC occurred
A High-Priority Machine Check caused
entry to PDCE_CHECK (the firmware
trap handler).
A Low-Priority Machine Check caused
entry to PDCE_CHECK (the firmware
trap handler).
72
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
WRN
CB73 SYS BD TOC occurred
A Transfer of Control caused entry to
PDCE_CHECK (the firmware trap
handler).
FLT
FLT
FLT
CB9r IO BD
Error on roper
An error was detected on rope r.
CB99 SYS BD seed IVA handler PDC_SEED_ERROR triggered an HPMC.
CB9A SYS BD HPMC overwrite
Firmware is overwriting PIM data from a
previous HPMC.
OFF
OFF
CBA1 SYS BD AIOC int dat err I/O controller internal error.
CBA2 IO BD
EtoA rope perr
Parity error between I/O controller and
Rope-to-PCI bridge.
OFF
OFF
CBA3 SYS BD access invld TLB An invalid I/O TLB entry was accessed.
CBA4 IO BD
EtoA rp cmd perr Command parity error between I/O
controller and Rope-to-PCI bridge.
OFF
OFF
CBA5 IO BD
CBA6 IO BD
CDF timeout
Rope Command/Data FIFO is backed up.
R2PCI resp tmout Rope-to-PCI bridge timed out. Could be a
failure of the PCI card, rope, or R2PCI
bridge.
OFF
OFF
CBA7 IO BD
CBB1 IO BD
Unknown AIOC err Unknown I/O controller error.
PCI timeout
A PCI card requested the bus but failed to
use it.
OFF
CBB2 IO BD
PCI timeout; OV
More than once aPCI card requested the
bus but failed to use it.
OFF
OFF
CBB3 IO BD
CBB4 IO BD
R2PCI intrnl err Rope-to-PCI bridge internal error.
R2PCI int err;OV Multiple Rope-to-PCI bridge internal
errors.
OFF
OFF
CBB6 IO BD
CBB8 IO BD
PCI data req err PCI bus data requestor error: R2PCI
detected PERR# assertion.
PCI D req err;OV Rope-to-PCI bridge detected multiple
PERR# assertions.
OFF
OFF
OFF
OFF
CBBA IO BD
CBBC IO BD
CBBE IO BD
CBC0 IO BD
PCI data par err PCI bus data parity error.
PCI Dpar err;OV
Multiple PCI bus data parity errors.
R2PCI intrnl err Error in R2PCI internal data to PCI bus.
R2PCI int err;OV Multiple R2PCI internal data to PCI bus
errors.
Chapter 3
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
OFF
CBC2 IO BD
CBC4 IO BD
CBC6 IO BD
CBC8 IO BD
PCI data parity
PCI data parity error. I/O error log word 3
contains the error address.
OFF
OFF
OFF
PCI data par; OV Multiple PCI data parity errors. I/O error
log word 3 contains the error address.
R2PCI intrnl err Rope-to-PCI bridge internal data error:
R2PCI detected PERR# assertion.
R2PCI int err;OV Multiple R2PCI internal data errors:
R2PCI detected multiple PERR#
assertions.
OFF
OFF
CBCA IO BD
CBCC IO BD
PCI data rs err
PCI bus data responder error: R2PCI
detected PERR# assertion.
PCI D rs err; OV Multiple PCI bus data responder errors:
R2PCI detected multiple PERR#
assertions.
OFF
OFF
CBCE IO BD
CBD0 IO BD
R2PCI T-Abort
Rope-to-PCI bridge signalled Target
Abort.
R2PCI T-Abort;OV Rope-to-PCI bridge signalled multiple
Target Aborts.
OFF
OFF
CBD2 IO BD
CBD4 IO BD
PCI parity err
PCI par err; OV
PCI address/command parity error.
Multiple PCI address/command parity
errors.
OFF
CBD6 IO BD
PCI no DEVSEL#
No PCI device selected (DEVSEL#
assertion). I/O error log word 3 contains
the error address.
OFF
OFF
CBD8 IO BD
CBDA IO BD
PCI no DEVSEL;OV Multiple DEVSEL# assertions. I/O error
log word 3 contains the error address.
PCI target abort A PCI device signalled Target Abort. I/O
error log word 3 contains the error
address.
OFF
CBDC IO BD
PCI T-Abort; OV
A PCI device signalled multiple Target
Aborts. I/O error log word 3 contains the
error address.
OFF
OFF
CBDD IO BD
CBDE IO BD
PCI assrts LOCK# A PCI device asserted LOCK#.
PCI LOCK#; OV
A PCI device asserted LOCK# multiple
times.
OFF
CBE0 IO BD
PCI assrts SERR# A PCI device asserted SERR#: address
parity error or other system error.
74
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
OFF
CBE2 IO BD
PCI SERR#; OV
A PCI device asserted SERR# multiple
times.
OFF
OFF
CBE3 IO BD
Unknown PCI err
Unknown PCI error detected.
CBE6 SYS BD AtoE rope perr
Parity error between system I/O controller
and Rope-to-PCI bridge.
OFF
OFF
CBE7 IO BD
R2PCI intrnl err Rope-to-PCI bridge internal data error.
CBE8 SYS BD AtoE rope perr
Command parity error between system
I/O controller and Rope-to-PCI bridge.
OFF
FLT
CBE9 IO BD
Unknown Rope err Unknown rope error occurred.
CBF0 SYS BD HPMC initiated
A High-Priority Machine Check entered
the firmware HPMC handler.
FLT
FLT
FLT
FLT
CBF1 SYS BD no OS HPMC IVA
There is no HPMC vector for the
operating system. Firmware will halt the
CPU, requiring a power cycle to recover.
CBF2 SYS BD bad OS HPMC len
The size of the operating system HPMC
handler is invalid. Firmware will halt the
CPU, requiring a power cycle to recover.
CBF3 SYS BD bad OS HPMC addr The operating system HPMC handler
vector is invalid. Firmware will halt the
CPU, requiring a power cycle to recover.
CBF4 SYS BD bad OS HPMC cksm The operating system HPMC handler
failed the checksum test. Firmware will
halt the CPU, requiring a power cycle to
recover.
FLT
CBF5 SYS BD OS HPMC vector 0 The size of the operating system HPMC
handler is zero. Firmware will halt the
CPU, requiring a power cycle to recover.
WRN
FLT
FLT
CBFA SYS BD prev HPMC logged Firmware detected unread PIM data from
a previous HPMC and will overwrite it.
CBFB SYS BD brnch to OS HPMC Branching to the operating system HPMC
handler.
CBFC SYS BD OS HPMC br err
Branch to the operating system HPMC
handler failed. Firmware will halt the
CPU, requiring a power cycle to recover.
FLT
FLT
CBFD SYS BD unknown check
CBFE SYS BD HPMC during TOC
The firmware trap handler didn’t detect
an HPMC, LPMC, or TOC.
A High-Priority Machine Check occurred
during Transfer of Control processing.
Chapter 3
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Selftest Failures
Ta b le 3-2. Ch a ssis Cod es for t h e B2000 Wor k st a t ion
Osta t
Cod e
F R U
Messa ge
Description
FLT
CBFF SYS BD multiple HPMCs
A High-Priority Machine Check occurred
while processing another HPMC.
INI
INI
CC0n SYS BD CPUn OS rendezvs
Slave CPU n entering the final
rendezvous, waiting for the operating
system to awaken it.
CC1n SYS BD CPUn early rend
Slave CPU n entering the early
rendezvous, waiting for the monarch CPU
to initialize scratch RAM and other
system state.
INI
INI
INI
CC2n SYS BD CPUn rendezvous
CC3n SYS BD CPUn cache rend
CC4n SYS BD CPUn mem rendez
Slave CPU n entering rendezvous. Slave
CPUs enter this rendezvous numerous
times during boot.
Slave CPU n entering cached rendezvous,
waiting for the monarch CPU to configure
the system bus.
Slave CPU n entering memory
rendezvous, waiting for the monarch CPU
to select a boot device.
TST
WRN
INI
INI
WRN
D000 SYS BD micro controller Firmware is initializing communications
with the system controller.
D004 SYS BD micro not resp
Firmware detected a communications
error with the system controller.
D005 SYS BD set dom1 fan spd Firmware is initializing communications
with the system controller.
D006 SYS BD set dom2 fan spd Firmware is initializing communications
with the system controller.
D007 SYS BD bad microctl cmd Firmware detected a communications
error with the system controller.
FLT
WRN
D01n SYS/IO fan n: failure!
D02n SYS/IO fan n: too slow!
Firmware detected fan n stopped.
Firmware detected fan n is running too
slowly.
76
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Memory Failures
Mem or y Fa ilu r es
The B2000 system implements Memory Page Deallocation. This feature allows the
workstation to provide information to the operating system about memory failures.
HP-UX 10.20 uses information to map out failing memory areas and continue normal
operation. You can use the command memrptwith the detailswitch to obtain information
about the Memory Page Deallocation Table (PDT) as well as single-bit errors logged by the
system, as follows:
# /usr/sbin/sysdiag Enter
DUI > logtool Enter
LOGTOOL> memrpt detail Enter
The PDT can also be checked using the pdt command in the Service menu of the Boot
Console Handler (refer to Chapter 6).
For allowable memory configurations, see the “Memory” section on page 38.
Chapter 3
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Running System Verification Tests
Ru n n in g System Ver ifica t ion Tests
HP-UX uses an online diagnostics product named Mesa (Support Tools Manager) that
allows system operation verification.
Three interfaces are available with the Support Tools Manager:
•
•
•
A command line interface accessed through the cstmcommand
A menu-driven interface accessed through the mstmcommand
A graphical user interface accessed through the xstmcommand
For more information on these user interfaces, see the online man pages by entering the
following at a command line prompt:
man cstmEnter
man mstmEnter
man xstm Enter
For information on the enhanced online diagnostics, see the Support Media User’s Manual
(HP Part Number B3782-90176).
To access the Support Tools Manager, perform the following steps:
1. In a terminal window, type the following at the #prompt to invoke the command line
interface:
# cstmEnter
2. The following message appears:
Support Tools Manager Version A.01.00
Type helpfor a list of available commands:
CSTM>helpEnter
3. To verify the system operation, type the following at the CSTM>prompt:
CSTM>verify allEnter
Messages similar to the following appear:
Verification has started on device (CPU).
Verification has started on device (FPU).
CSTM> Verification of(FPU) has completed.
CSTM> Verification of(CPU) has completed.
4. Press Enter to return to the CSTM>prompt after all test results are reported.
5. To exit the Support Tools Manager, enter the following:
CSTM>exitEnter
If any tests failed, run Self Test and ISL diagnostics to isolate the problem.
78
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Running ODE-Based Diagnostics
Ru n n in g ODE-Ba sed Dia gn ostics
The Offline Diagnostic Environment (ODE) consists of diagnostic modules for testing and
verifying system operation. ODE provides all the necessary functions for the user to load
specified tests and interact with those tests.
ODE is an ISL utility. To boot ODE:
1. Invoke the ISL environment from the system disk or CD.
2. Type ode Enter after the ISL> prompt to invoke ODE from the LIF directory on the
system disk. The prompt changes to ODE>.
Not all of the test modules are available on all systems. To see what test modules are
available to run on this system, type lsat the ODE>prompt. The available modules include
the following:
• wdiag– tests and verifies the basic functionality of the PA-RISC chip. This tool tests the
CPU, cache, TLB, and floating point functions.
• memtest– tests and verifies the memory arrays. If an error is detected, the diagnostic
reports the memory card and its slot number that needs replacement. It also provides a
map of the memory configuration so that the user can identify the types of memory and
its slot location.
• mapper– identifies the configuration of HPPA systems. It displays path, identification,
and revision information of I/O components, configuration of memory controllers,
processors, co-processors, cache, and TLB, as well as processor board component
revisions and values of various HPPA system identifiers, revisions, and capabilities.
• astrodiag– tests and verifies the basic functionality of the Astro memory/IO controller
chip.
• siodiag – tests and verifies the functionality of the super IO multifunction IO chip,
including serial, parallel, USB, and so forth.
For further information on the various ODE commands and a complete listing of the
command set, type help Enter at the ODE> prompt or at the prompt of one of the test
modules.
Usin g th e P IM Du m p Tool to Decod e HP MCs
If the system HPMC and halts, the Boot Console Handler’s Service menu provides a PIM
dump tool that can analyze the HPMC dump and attempt to decode it for analysis. It will
point to the failing FRU or memory location if it is memory related. For information on
using the Boot Console Handler, see Chapter 6.
Chapter 3
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Running ODE-Based Diagnostics
80
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Field Rep la cea ble Un its
This chapter lists the HP VISUALIZE B2000 workstation’s Field Replaceable Units (FRUs)
and provides procedures and illustrations showing their removal and replacement.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
Chapter Overview
Ch a p t er Over view
This chapter contains the following main sections:
•
•
Exchange and Non-Exchange Part Numbers
FRU Removal and Replacement
— Front Panel
— Left Side Panel
— Power Switch/LCD Assembly
— Removable Media Devices
— CD Drive
— Floppy Disk Drive
— Hard Disk Drives
— I/O Cards
— Battery
— Memory DIMMs
— Power Supply
— Voltage Regulator Modules
— Fans
— I/O Fan
— System Fan
— Speaker
— System Board Tray Assembly
WARNING
NOTE
For a ll r em ova l a n d r ep la cem en t p r oced u r es in t h is ch a p t er, you
m u st p ow er off t h e w or k st a t ion a n d u n p lu g t h e w or k st a t ion ’s p ow er
cor d fr om t h e AC p ow er ou t let .
To maintain FCC/EMI compliance, verify that all covers are replaced, all
screws are properly seated, and all gasket material is intact.
82
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
Chapter Overview
Tools R equ ir ed
Use the following tools to remove or replace FRUs in the B2000 workstation:
•
•
•
•
Torx T-15 driver
Light-duty flat blade screw driver with 6-inch (150 mm) blade
Needle-nose pliers
ESD equipment (see “Electrostatic Discharge (ESD) Precautions” on page 177)
Exp lod ed View Dia gr a m
Figure 4-1 shows an exploded view of the FRUs in the B2000 workstation. Refer to this
figure for the locations of the various workstation FRUs while performing the FRU
removal and replacement procedures in this chapter.
Figu r e 4-1. Exp lod ed View Dia gr a m of t h e B2000 Wor k st a t ion F RUs
I/O Fan
Air Divider
in Bracket
PCI
Retainer
Clip
Chassis
Speaker
System Fan
DIMM
CD Drive
Bracket
Cards
Battery
Floppy Disk
Drive Bracket
Hard Disk Drive
and Bracket
Left Side
Panel
Voltage
Front Panel
Regulator
Modules
(Master
Power
Supply
System Board
Tray Assembly
and Slave)
Chapter 4
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
Exchange and Non-Exchange Part Numbers
Exch a n ge a n d Non -Exch a n ge Pa r t Nu m ber s
In this chapter we refer to exchange and non-exchange part numbers.
You must return FRUs with exchange part numbers in exchange for a replacement FRU.
Do not return FRUs with non-exchange part numbers—you may discard them.
The exploded view diagram (Figure 4-1 on page 83) shows the B2000 workstation’s FRUs.
Table 4-1 lists the exchange parts, and Table 4-2 lists the non-exchange parts in the B2000
workstation.
Ta b le 4-1. Exch a n ge P a r t Nu m ber s
Part Number
Description
A5983-69001
A3862-69001
A3863-69001
A1658-69028
400 MHz PA8600 CPU Assembly
256 MB SDRAM DIMM
512 MB SDRAM DIMM
9 GB 7200 RPM LVD Disk
Ta b le 4-2. Non -E xch a n ge Pa r t Nu m b er s
Part Number
Description
A5983-62011
0950-3758
400 W Power Supply
Master Voltage Regulator Module
Slave Voltage Regulator Module
3.5-inch Floppy Disk Drive
ATAPI CD Drive
0950-3759
D2035-60391
D4389-60021
5063-4513
Speaker
A4978-62025
A1280-68503
A1280-68504
A4983-60401
A4983-60111
A4983-60101
A4986-62025
A5983-62009
LCD/Power Switch Assembly
I/O Fan, 92 mm
System Fan, 120 mm
USB Keyboard, U.S.
USB Three-Button Mouse, U.S.
USB Scroll-Wheel Mouse, U.S.
PCI Retainer Clip
Front Bezel with Floppy Disk Bay Filler
84
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
Exchange and Non-Exchange Part Numbers
Ta b le 4-2. Non -E xch a n ge Pa r t Nu m b er s
Part Number
Description
A5983-63001
5182-1857
CD Signal Cable
CD Audio Cable
A5983-63002
A4986-63006
A5983-62007
A5983-62010
A4986-62006
0624-0727
Floppy Disk Drive Signal Cable
LCD Signal Cable
Hard Disk Drive Bracket
CD Drive Bracket Assembly
Floppy Disk Drive Bracket Assembly
6 - 32 × 1.437 T-15 Torx Screws
Power Supply Screw
0515-0431
1826-4269
Real Time Clock Module (includes Battery)
Chapter 4
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
F RU Rem ova l a n d Rep la cem en t
The procedures in this section describe how to remove and replace (install) field
replaceable units (FRUs). Observe any notices and prerequisites before removing an FRU.
Befor e p er for m in g a n y F R U r em ova l or r ep la cem en t p r oced u r e, you m u st d o t h e
follow in g:
1. Power off the workstation, the monitor, and any peripheral devices.
NOTE
There is no need to manually shutdown the HP-UX operating system on the
workstation before switching it off. When the front panel power switch is
pressed to off, the workstation automatically shuts down the operating
system before terminating the power. Wait for the system to completely
shutdown and power off before disconnecting the power cord.
CAUTION
Unplugging the power cord while HP-UX is running can damage system files.
2. Unplug the workstation’s power cord and the power cord of any peripheral devices from
AC wall outlets.
3. Unplug the workstation’s power cord from the AC input connector on the rear of the
workstation.
4. Disconnect any external cables from the connectors on the rear of the workstation.
5. Attach a static-grounding wrist strap to your wrist. Attach the sticky end of the wrist
strap to bare metal on the rear panel of the workstation.
6. Lay the workstation on a flat stable surface, such as a table top or floor. To protect
against scratches, remove miscellaneous debris and preferably use an ESD mat to
cushion the workstation.
CAUTION
Follow normal ESD anti-static precautions when handling the workstation or
any of its components. (See the section titled “Electrostatic Discharge (ESD)
Precautions” on page 177.) Failure to do so can cause component degradation
or failure.
7. If installed, remove any locking device from the security loop on the rear of the
workstation.
86
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Fr on t Pa n el
This section explains how to open and close the workstation’s front panel.
Op en in g t h e Fr on t Pa n el
Perform the following steps to open the front panel:
1. Power off the workstation and unplug the power cord from the electrical outlet.
2. Attach the static-grounding wrist strap by following the instructions on the package.
Attach the sticky end of the wrist strap to bare metal on the rear panel of the
workstation.
3. Unlatch the front panel by pressing in on the two latch buttons located on the right side
of the front panel, as shown in Figure 4-2.
Figu r e 4-2. Op en in g t h e F r on t P a n el
Latch
Button
Latch
Button
4. Swing the front panel outward on its left hinge hooks until the panel comes free.
5. Place the front panel in a location where it cannot be damaged.
Closin g t h e F r on t P a n el
Perform the following steps to close the front panel:
1. Locate the three hinge hooks on the left side of the front panel and insert them into the
rectangular holes located along the front, left edge of the workstation.
2. Rotate the front panel inward until you hear the two latch buttons snap in place. The
front panel is now closed.
Chapter 4
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Left Sid e Pa n el
This section explains how to open and close the left side panel. You will need to open this
side panel whenever you need to access the internal components of the workstation.
Op en in g t h e Left Sid e P a n el
Perform the following steps to open the left side panel:
1. Power off the workstation and unplug the power cord from the electrical outlet.
WARNING
Alw a ys u n p lu g t h e w or k st a t ion ’s p ow er cor d fr om t h e elect r ica l
ou t let b efor e op en in g t h e w or k st a t ion .
2. Attach the static-grounding wrist strap by following the instructions on the package.
Attach the sticky end of the wrist strap to bare metal on the workstation’s rear panel.
3. Remove the two T-15 Torx thumbscrews located on the top and bottom, right edge of the
workstation’s rear panel, as shown in Figure 4-3.
4. Grasp the rear edge of the left side panel and rotate it outward approximately 30
degrees to the workstation. Next, pull the panel toward you as shown in Figure 4-3.
This releases the panel’s top and bottom hinge hooks from their hinge slots.
Figu r e 4-3. Op en in g t h e Left Sid e Pa n el
Hinge Hook
T-15 Torx
Thumbscrew
EMI Gasket
Hinge Hook
T-15 Torx
Thumbscrew
Left Side Panel
NOTE
The EMI gasket, as shown in Figure 4-3, must not be removed from the left
side panel.
88
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Closin g t h e Left Sid e Pa n el
Perform the following steps to close the left side panel:
1. Hold the left side panel so that the top and bottom hinge hooks can be inserted into
their hinge slots. See Figure 4-3. Note that the hinge slots are located on the far right
edge of the workstation (using the rear of the workstation as the reference).
2. Swing the rear edge of the left side panel toward the rear of the workstation and press
the outside edges of the left side panel tightly against the workstation. This will ensure
a tight seal of the EMI gasket.
3. Secure the left side panel in place by tightening the two T-15 Torx thumbscrews you
previously removed into the workstation’s rear panel.
Chapter 4
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Pow er Sw itch /LCD Assem bly
This section explains how to remove and replace the power switch/LCD assembly, which is
located on the front panel of the B2000 workstation.
Rem ovin g t h e P ow er Sw it ch /LCD Assem bly
Perform the following steps to remove the power switch/LCD assembly:
1. Open the workstation’s front panel as shown in the section “Opening the Front Panel.”
2. Unplug the power switch/LCD assembly’s connector as shown in Figure 4-4.
Figu r e 4-4. R em ovin g t h e Pow er Sw it ch /LCD Assem b ly
Power Switch/LCD
Assembly Connector
Right Side
Mounting Clip
Power Switch/LCD
Assembly
Left Side
Mounting Clips
3. Press inward on the mounting clip located on the right side of the power switch/LCD
assembly and pull the right side of the assembly outward in a clockwise motion. See
Figure 4-4. This action releases the mounting clips on the left side of the power
switch/LCD assembly.
Rep la cin g t h e P ow er Sw it ch /LCD Assem bly
Perform the following steps to replace the power switch/LCD assembly:
1. Open the workstation’s front panel as shown in the section “Opening the Front Panel.”
2. Insert the mounting clips on the left side of the power switch/LCD assembly into the
slots on the workstation chassis. See Figure 4-4.
3. Press inward on the mount clip located on the right side of the power switch/LCD
assembly and insert this clip into the hole provided for it on the workstation chassis.
4. Plug in the power switch/LCD assembly’s connector.
5. Close the workstation’s front panel as shown in the section “Closing the Front Panel.”
90
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Rem ova ble Med ia Devices
There are only two removable media devices allowed in a B2000 workstation:
•
•
CD drive (standard component)
3.5-inch floppy disk drive (optional component)
The procedures in the following subsections explain how to remove and replace (install)
these removable media devices.
Rem ovin g a n d Rep la cin g a CD Dr ive
WARNING
CAUTION
Pow er off t h e w or k st a t ion a n d u n p lu g t h e p ow er cor d b efor e
r em ovin g a n d r ep la cin g (in st a llin g) a CD d r ive.
CD drives are susceptible to mechanical and electrostatic shock. When
handling the drive, always wear the static-grounding wrist strap that came in
the CD drive kit. Always handle the drive carefully.
Perform the following steps to remove and replace a CD drive:
1. Open the front and left side panels of the workstation as shown in the sections
“Opening the Front Panel” and “Opening the Left Side Panel.”
2. Remove the rear cover of the CD drive bay inside the workstation by unscrewing the
T-15 Torx/slotted screw as shown in Figure 4-5. Push the cover handle toward the rear
of the CD drive approximately one inch, and then pull the cover handle toward you.
Figu r e 4-5. R em ovin g t h e CD Dr ive Ba y’s R ea r Cover
Rear Cover
Rear
Handle
Cover
T-15
Torx/Slotted
Screw
Audio
Cable
ATAPI Cable
Power Cable
3. Disconect the audio, ATAPI, and power cables from the rear of the CD drive.
Chapter 4
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
4. Rotate the workstation around until you see the front of the workstation as shown in
Figure 4-6.
Figu r e 4-6. F r on t of t h e Wor k st a t ion w it h t h e Fr on t Pa n el Rem oved
LCD
Bracket Screw
(hidden)
CD Drive
Bracket Screw
5. Remove both CD drive bracket screws (T-15 Torx/slotted screws) and pull the CD drive
out of the workstation chassis as shown in Figure 4-7.
Figu r e 4-7. R em ovin g t h e CD Dr ive
CD Drive
CD Drive Mounting
Screws (T-15 Torx)
CD Drive Mounting
Screws (T-15 Torx)
Bracket Screws
(T-15 Torx)
CD Drive Bracket
6. Remove the four CD drive mounting screws (T-15 Torx/slotted screws) from the sides of
the CD drive bracket as shown in Figure 4-7 and remove the CD drive from the bracket.
92
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
7. Remove the new CD drive from its shipping container and check to see that the jumper
on the rear of the CD drive is set to the CSEL position.
NOTE
You will have to verify that the master/slave/CSEL jumper is set in the CSEL
position on the rear of the new CD drive that you will install. Since different
CD drive manufacturers have different locations for the CSEL jumper, look
at the documentation that came with the CD drive for the proper location of
this jumper.
8. Using the four CD drive mounting screws, mount the CD drive to the bracket as shown
in Figure 4-8. Note that the CD drive should extend approximately one inch out from
the front of the CD drive bracket.
Figu r e 4-8. In st a llin g t h e CD Dr ive
CD Drive Bracket Guide
CD Drive
CD Drive Mounting
Screws (T-15 Torx)
Bracket
Runner
CD Drive Mounting
Screws (T-15 Torx)
Bracket Screws
9. Slide the CD drive and its bracket into the workstation chassis as shown in Figure 4-8.
There are runners on the sides of the bracket and guides inside the CD drive chassis
that will help the CD drive and bracket assembly to slide into place.
Chapter 4
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
10.Tighten the two CD drive bracket screws as shown in Figure 4-9.
Figu r e 4-9. Tigh t en in g t h e Br a ck et Scr ew s
Bracket
Screw
(hidden)
Bracket Screw
11.Rotate the workstation around until you see the open, left side of the workstation. Plug
the audio, ATAPI, and power cables into their appropriate connectors on the rear of the
CD drive, as shown in Figure 4-10. Note that the connectors are keyed for proper
insertion, and that you should connect the audio cable first.
NOTE
The red striped side of the ATAPI cable should be positioned next to the
power cable.
Figu r e 4-10. P lu ggin g in t h e Au d io, ATAP I, a n d P ow er Ca b les
Audio
Cable
Ferrite Bead
ATAPI Cable
Power Cable
94
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
12.Make sure that the audio, ATAPI, and power cables are positioned so that they will
come out of the bottom edge of the CD drive bay’s rear cover when it is replaced. (Note
that the rear cover’s bottom edge is rounded to prevent cutting of the cables.) To replace
the rear cover, place the end opposite of the rear cover handle into the cover slot and
rotate it into place. Tighten the T-15 Torx/slotted screw to secure the rear cover. Note
that, when you replace the rear cover, the ferrite bead on the ATAPI cable must remain
outside of the CD drive bay’s rear cover. See Figure 4-11.
Figu r e 4-11. R ep la cin g t h e CD Dr ive Ba y’s R ea r Cover
Rear Cover
T-15
Torx/Slotted
Screw
Ferrite Bead
13.Make sure that all cables are positioned within the workstation so that they cannot be
damaged. Then close the left side and front panels of the workstation as shown in the
sections “Closing the Left Side Panel” and “Closing the Front Panel.”
Chapter 4
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Rem ovin g a F lop p y Disk Dr ive
WARNING
CAUTION
Pow er off t h e w or k st a t ion a n d u n p lu g t h e p ow er cor d b efor e
r em ovin g t h e flop p y d isk d r ive.
Floppy disk drives are susceptible to mechanical and electrostatic shock.
When handling the drive, always wear the static-grounding wrist strap that
came in the floppy disk drive kit. Always handle the drive carefully.
Perform the following steps to remove a floppy disk drive:
1. Open the front and left side panels of the workstation as shown in the sections
“Opening the Front Panel” and “Opening the Left Side Panel.”
2. Remove the rear cover of the floppy disk drive bay inside the workstation by unscrewing
the T-15 Torx/slotted screw as shown in Figure 4-12. Push the cover handle toward the
rear of the floppy disk drive approximately one inch, and then pull the cover handle
toward you.
Figu r e 4-12. R em ovin g t h e F lop p y Disk Dr ive Ba y’s R ea r Cover
Rear Cover Handle
T-15
Torx/Slotted
Screw
Power Cable
Rear Cover
Data Cable
3. Disconnect the power and data cables from the rear of the floppy disk drive.
4. Rotate the workstation around until you can see the front of the workstation as shown
in Figure 4-13.
96
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Figu r e 4-13. Fr on t of Wor k st a t ion w it h t h e Fr on t Pa n el Rem oved
LCD
Bracket
Screw
(hidden)
Floppy
Disk Drive
Bracket Screw
5. Remove both floppy disk drive bracket screws (T-15 Torx/slotted screws) and pull the
floppy disk drive out of the workstation chassis as shown in Figure 4-14.
Figu r e 4-14. R em ovin g t h e F lop p y Disk Dr ive
Floppy
Disk Drive
Floppy Disk Drive
Mounting Screws
(T-15 Torx)
Floppy Disk Drive
Mounting Screws
(T-15 Torx)
Floppy Disk
Drive Bracket
Bracket Screws
(T-15 Torx)
6. Remove the four floppy disk drive mounting screws (T-15 Torx/slotted screws) from the
sides of the floppy disk drive bracket as shown in Figure 4-14 and remove the floppy
disk drive from the bracket.
Chapter 4
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
If you will replace the floppy disk drive with a blank, continue on with step 7 below.
However, if you will replace it with a new floppy disk drive, go to step 6 in the section
“Replacing or Installing a Floppy Disk Drive” on page 101.
7. Place the floppy disk drive blank in the floppy disk drive bracket and tighten the four
floppy disk drive mounting screws (T-15 Torx/slotted screws) into the bracket. See
Figure 4-15.
Figu r e 4-15. In st a llin g t h e F lop p y Disk Dr ive Bla n k a n d Br a ck et
Floppy Disk
Drive Bracket
Floppy Disk Drive
Mounting Screws
Floppy Disk
Drive Blank
Floppy Disk Drive
Mounting Screws
8. Slide the floppy disk drive blank and its bracket into the workstation chassis as shown
in Figure 4-15.
9. Tighten the two floppy disk drive bracket screws as shown in Figure 4-16.
Figu r e 4-16. Tigh t en in g t h e Br a ck et Scr ew s
Bracket Screw
Bracket Screw
98
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
10.Make sure that the floppy disk drive’s power and data cables are positioned so that they
will come out of the top edge of the floppy disk drive bay’s rear cover when it is replaced.
(Note that the rear cover’s top edge is rounded to prevent cutting of the cables.) Put the
rear cover in place and tighten the T-15 Torx/slotted screw. See Figure 4-17.
Figu r e 4-17. R ep la cin g t h e F lop p y Disk Dr ive Ba y’s R ea r Cover
T-15
Torx/Slotted
Screw
Power
Cable
Rear Cover
Data Cable
11.Replace the plastic floppy disk drive blank in the workstation’s front panel.
12.Make sure that all cables are positioned within the workstation so that they cannot be
damaged. Then close the left side and front panels of the workstation as shown in the
sections “Closing the Left Side Panel” and “Closing the Front Panel.”
Rep la cin g or In st a llin g a F lop p y Disk Dr ive
WARNING
CAUTION
Pow er off t h e w or k st a t ion a n d u n p lu g t h e p ow er cor d b efor e
r ep la cin g (in st a llin g) t h e flop p y d isk d r ive.
Floppy disk drives are susceptible to mechanical and electrostatic shock.
When handling the drive, always wear the static-grounding wrist strap that
came in the floppy disk drive kit. Always handle the drive carefully.
NOTE
There are no jumper settings required for the installation of the floppy disk
drive.
Perform the following steps to replace a floppy disk drive:
1. Open the front and left side panels of the workstation as shown in the sections
“Opening the Front Panel” and “Opening the Left Side Panel.”
Chapter 4
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
2. Remove the rear cover of the floppy disk drive bay inside the workstation by unscrewing
the T-15 Torx/slotted screw as shown in Figure 4-18. Push the cover handle toward the
rear of the floppy disk drive approximately one inch, and then pull the cover handle
toward you.
Figu r e 4-18. R em ovin g t h e F lop p y Disk Dr ive Ba y’s R ea r Cover
Rear Cover Handle
T-15
Power
Cable
Torx/Slotted
Screw
Rear Cover
Data Cable
3. Rotate the workstation around until you see the front of the workstation as shown in
Figure 4-19.
Figu r e 4-19. Fr on t of Wor k st a t ion w it h t h e Fr on t Pa n el Rem oved
LCD
Floppy Disk
Bracket Screw
Drive Blank
Bracket Screw
100
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
4. Remove both floppy disk drive bracket screws (T-15 Torx/slotted screws) and pull the
floppy disk drive bracket out of the workstation chassis as shown in Figure 4-20.
Figu r e 4-20. R em ovin g t h e F lop p y Disk Dr ive Br a ck et a n d Bla n k
Floppy Disk
Drive Bracket
Floppy Disk Drive
Mounting Screws
(T-15 Torx)
Bracket
Screw
Floppy Disk Drive
Mounting Screws
(T-15 Torx)
Bracket Screw
Floppy Disk
Drive Blank
5. Remove the four floppy disk drive mounting screws (T-15 Torx/slotted screws) from the
sides of the floppy disk drive bracket as shown in Figure 4-20 and remove the floppy
disk drive blank from the bracket.
6. Remove the new floppy disk drive from its shipping container. Using the four T-15
Torx/ slotted mounting screws, mount the floppy disk drive to the bracket as shown in
Figure 4-21.
To help you properly install the floppy disk drive, you need to use the floppy disk drive
holes labeled “A” on the bracket sides. The first T-15 Torx screws should be inserted
through the tab holes of the floppy disk drive bracket that are located on the front part
of both sides of the bracket. These T-15 Torx screws should then be screwed into the
screw holes located on both sides of the floppy disk drive. These holes are located near
the floppy disk drive’s front panel. The remaining T-15 Torx screws should be inserted
through the holes labeled “A” at the rear part of the floppy disk drive bracket. These
screws should then be screwed into the rear screw holes located on both sides of the
floppy disk drive. Note that the front of the floppy disk drive should extend one inch
from the front of the floppy disk drive bracket. See Figure 4-21.
Chapter 4
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Figu r e 4-21. In st a llin g t h e F lop p y Disk Dr ive
Floppy Disk Drive
Mounting
Screws
Mounting
Screws
Bracket Screws
7. Slide the floppy disk drive and its bracket into the workstation chassis as shown in
Figure 4-21.
8. Tighten the two floppy disk drive bracket screws as shown in Figure 4-22.
Figu r e 4-22. Tigh t en in g t h e Br a ck et Scr ew s
Bracket
Screw
(hidden)
Bracket
Screw
102
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
9. Rotate the workstation around until you see the open, left side of the workstation. Plug
the power and data cables into their connectors on the rear of the floppy disk drive, as
shown in Figure 4-23. Note that the connectors are keyed for proper insertion.
NOTE
The red striped side of the data cable should be positioned toward the power
cable.
Figu r e 4-23. P lu ggin g in t h e Pow er a n d Da t a Ca b les
Power
Cable
Data Cable
10.Make sure that the floppy disk drive’s power and data cables are positioned so that they
will come out of the top edge of the floppy disk drive bay’s rear cover when it is replaced.
(Note that the rear cover’s top edge is rounded to prevent cutting of the cables.) Put the
rear cover in place and tighten the T-15 Torx/slotted screw. Note that, when you replace
the rear cover, the ferrite bead on the data cable must remain inside of the floppy disk
drive bay’s rear cover. See Figure 4-24.
Figu r e 4-24. R ep la cin g t h e F lop p y Disk Dr ive Ba y’s R ea r Cover
T-15
Torx/Slotted
Screw
Power Cable
Rear Cover
Data Cable
11.Remove the plastic floppy disk drive blank from the workstation’s front panel, if
present.
12.Make sure that all cables are positioned within the workstation so that they cannot be
damaged. Then close the left side and front panels of the workstation as shown in the
sections “Closing the Left Side Panel” and “Closing the Front Panel.”
Chapter 4
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Ha r d Disk Dr ives
This section explains how to remove and replace (install) a hard disk drive in the B2000
workstation. After replacing or installing a hard disk drive, be sure to follow the
procedures in the section “Configuring a Hard Disk Drive as a File System” on page 33 to
configure the hard disk drive.
The B2000 workstation can have a maximum of two hard disk drives. These internal hard
disk drives are devices on the Ultra2 Wide Low-Voltage Differential SCSI bus. The hard
disk drive that came with the workstation was set to SCSI ID 6 on the bus. If you are
adding a second hard disk drive, the second hard disk drive will use SCSI ID 5. Note that
the two slots for the hard disk drives have SCSI ID numbers 6 and 5 preassigned to them,
and that SCSI ID 6 is the system disk. You will not be able to change these SCSI ID
numbers.
CAUTION
Hard disk drives are susceptible to mechanical and electrostatic shock. When
handling the drive, always wear the static-grounding wrist strap that came in
the hard disk drive kit. Always handle the drive carefully.
Rem ovin g a H a r d Disk Dr ive
CAUTION
NOTE
To remove a hard disk drive, the workstation must be turned off.
There are no cables to disconnect when removing a hard disk drive.
NOTE
If you are removing a hard disk drive that has a mounted file system on it,
you will need to unmount it. This should be done before you remove the hard
disk drive itself from the workstation.
To unmount a file system on a hard disk drive, follow the procedure in the
section “Removing a Hard Disk Drive as a File System” on page 35.
Perform the following steps to remove a hard disk drive:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.” As you face the open, left side of the workstation, the hard disk drives are
on the right side. The lower hard disk drive (SCSI ID 5) is the one discussed in this
section. See Figure 4-25.
104
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Figu r e 4-25. Loca t ion of t h e H a r d Disk Dr ives
Upper Hard Disk Drive
(SCSI ID 6 -- System Disk
Lower Hard Disk Drive
(SCSI ID 5)
2. Loosen the T-15 Torx thumbscrew securing the hard disk drive assembly to the system
board. Grasp the assembly and slide it to the front of the workstation to unseat the
bracket from the chassis rail. See Figure 4-26. You may need to angle the hard disk
drive assembly slightly to disengage the hooks as you slide it along the rail.
Figu r e 4-26. R em ovin g t h e Ha r d Disk Dr ive
T-15 Torx Thumbscrew
Chapter 4
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
3. Remove the four T-15 Torx mounting screws from the bracket as shown in Figure 4-27.
Be careful when removing the hard disk drive from its bracket to avoid damaging it.
Figu r e 4-27. R em ovin g t h e Ha r d Disk Dr ive fr om It s Br a ck et
T-15 Torx
Mounting Screw
Mounting Grommets
(Do NOT Remove)
4. Screw the four mounting screws into the four vertical holes on the hard disk drive
bracket to store them for future use.
5. Slide the hard disk drive bracket into its slot, and push firmly inward to secure the hard
disk drive bracket to the system board connector. See Figure 4-28.
Figu r e 4-28. R ep la cin g t h e Ha r d Disk Dr ive Br a ck et
T-15 Torx Thumbscrew
6. Tighten the T-15 Torx thumbscrew to secure the bracket to the system board.
7. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
106
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Rep la cin g or In st a llin g a H a r d Disk Dr ive
NOTE
After replacing or installing a hard disk drive, you will need to mount it and
create a file system on it. Follow the procedures in the section “Configuring a
Hard Disk Drive as a File System” on page 33.
1. Remove the left side panel of the workstation using the instructions found in the section
“Opening the Side Panel.” As you face the open, left side of the workstation, the hard
disk drives are on the right side. The lower hard disk drive (SCSI ID 5) is the one
discussed in this section. Figure 4-29 shows an empty bracket for the lower hard disk
drive.
Figu r e 4-29. Loca t ion of t h e H a r d Disk Dr ives
Upper Hard Disk Drive
(SCSI ID 6 -- System Disk)
Bracket for the Lower
Hard Disk Drive (SCSI ID 5)
T-15 Torx Thumbscrew
2. Loosen the T-15 Torx thumbscrew securing the hard disk drive bracket to the system
board. See Figure 4-29. Grasp the bracket and slide it to the front of the workstation to
unseat the bracket from the chassis rail. You may need to angle the hard disk drive
bracket slightly to disengage the hooks as you slide it along the rail.
3. Mount the hard disk drive on the hard disk drive bracket using the four T-15 Torx
mounting screws that are stored on the bracket. See Figure 4-30 for the location of the
mounting screws and Figure 4-31 for positioning the bracket on to the hard disk drive.
Chapter 4
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Figu r e 4-30. R em ovin g th e T-15 Tor x Mou n tin g Scr ew s
Figu r e 4-31. Posit ion in g t h e Br a ck et on t o t h e H a r d Disk Dr ive
4. Insert the T-15 Torx mounting screws through the four rubber mounting grommets and
into the screw holes of the hard disk drive. See Figure 4-32.
Figu r e 4-32. Mou n t in g t h e Br a ck et on t o t h e Ha r d Disk Dr ive
T-15 Torx
Mounting Screw
Mounting Grommets
108
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
5. Slide the hard disk drive assembly into its slot, and push inward firmly until the front
of the hard disk drive bracket is flush with the hard disk drive connector on the system
board. See Figure 4-33. The bracket hooks will lock into the chassis rail.
Figu r e 4-33. Posit ion in g t h e H a r d Disk Dr ive Assem bly
T-15 Torx Thumbscrew
6. Tighten the T-15 Torx thumbscrew to secure the hard disk drive assembly to the system
board.
7. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
Chapter 4
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
I/O Ca r d s
This section explains how to remove and replace (or install) I/O cards in the B2000
workstation.
The B2000 workstation’s system board has four Peripheral Connect Interface (PCI) slots
for option I/O cards. Slots 1 and 2 are full-size (PCI-2X) slots. Slots 3 and 4 are half-size
(PCI-1X) slots.
NOTE
The optional graphics cards supported by the B2000 workstation are designed
to be electrically compatible with the PCI slots. See Table 1-1 in Chapter 1 for
the optional graphics cards supported in the B2000 workstation.
Figure 4-34 provides a brief description of slot capabilities.
Figu r e 4-34. P CI Ca r d Slot Nu m b er in g a n d Ca p a b ilit ies
Slot 1
Slot 2
Slot 3
Slot 4
64-b its, 5V, 33MH z
64-b its, 5V, 33MH z
32-b its, 5V, 33MH z
32-b its, 5V, 33MH z
The information described in Figure 4-34 is also provided on the B2000 system label on the
chassis floor inside the workstation. See Figure 4-35 for the location of the system label.
Figu r e 4-35. B2000 Syst em La bel
Front of the
Workstation
B2000 System Label
110
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
NOTE
If you are installing an additional HP VISUALIZE-fxe graphics card, after you
connect the monitor to the additional graphics card, you must change the
graphics path for the monitor. To do this, see the section “Displaying and
Setting the Monitor Type” on page 150.
As shown in Figure 4-36, the four I/O slots as seen from the rear of the workstation are
labeled from top to bottom starting with 1.
Figu r e 4-36. I/O Slot Nu m b er in g
I/O Slot 1
{
I/O Slot 4
Rem ovin g I/O Ca r d s
This subsection assumes that you already have I/O cards loaded in the workstation, and
that you need to remove one or more of them.
Perform the following steps to remove an I/O card:
1. Power off the workstation and unplug the power cord from the electrical outlet.
2. Attach the static-grounding wrist strap by following the instructions on the package.
Attach the sticky end of the wrist strap to bare metal on the rear panel of the
workstation.
3. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
4. Remove the PCI retainer clip by pulling evenly in the direction of the arrow on both
PULL tabs.
Chapter 4
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
5. Locate the I/O card you want to remove and, using a T-15 Torx driver or flathead
screwdriver, remove the I/O card’s bulkhead screw as shown in Figure 4-37.
Figu r e 4-37. R em ovin g t h e I/O Ca r d
I/O Card’s
Bulkhead
Screw
I/O Card
Bulkhead
I/O Card Being Removed
6. Pull evenly on the outside edges of the I/O card to remove it.
Rep la cin g or In st a llin g I/O Ca r d s
Perform the following steps to replace or install a new I/O card:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Locate the appropriate slot for the I/O card that will be installed.
3. Unscrew the T-15 Torx screw from the bulkhead blank of the slot you have chosen and
remove the bulkhead blank. If no blank is present, simply go on to step 4.
4. Remove the PCI retainer clip by pulling evenly in the direction of the arrow on both
PULL tabs.
5. Insert the I/O card into the slot you have chosen with the bulkhead appropriately
positioned. If the card is full-length, the non-bulkhead end of the card should be placed
in the I/O card guide. Press firmly and evenly on the I/O card until it is in the connector.
Screw the T-15 Torx screw into the I/O card’s bulkhead to secure the I/O card.
6. Replace the PCI retainer clip by placing the bottom hook in the slot on the air divider
and pushing the PULL tabs until they snap into their slots on the chassis wall.
7. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
NOTE
If you connect the monitor to a graphics I/O card that you have just installed,
you must change the graphics path for the monitor. To do this, see the section
“Displaying and Setting the Monitor Type” on page 150.
112
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Ba tter y
The battery in the B2000 workstation is contained within the real time clock module (Part
Number 1826-4269) on the system board. The component reference designation for the real
time clock module is U30 on the system board.
Perform the following steps to remove and replace the battery:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Locate the real time clock module, which has the component reference designation of
U30 on the system board. As shown in Figure 4-38, the real time clock module is to the
right of the system fan, just under the air flow guide.
Figu r e 4-38. Loca t ion of t h e R ea l Tim e Clock Mod u le
Real Time
Clock Module
3. Carefully remove the defective real time clock module. Note the polarity dot which is
silk-screened on the component side of the circuit board.
CAUTION
Danger of explosion if the battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of
used batteries according to the manufacturer’s instructions
CAUTION
Il y a danger d´explosion s´il y a remplacement incorrect de la batterie.
Remplacer uniquement acvec une batterie du même type ou d´un type
recommandé par le constructeur. Mettre au rébut les batteries usagées
conformément aux instructions du fabricant.
4. Insert the new real time clock module (Part Number 1826-4269) on the system board
with the correct polarity to ensure proper functionality.
5. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
Chapter 4
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Mem or y DIMMs
This section explains how to remove and replace (or install additional) memory DIMM
cards in the B2000 workstation.
Rem ovin g Mem or y DIMMs
WARNING
Alw a ys u n p lu g t h e w or k st a t ion ’s p ow er cor d fr om t h e elect r ica l
ou t let or p ow er sou r ce b efor e op en in g t h e w or k st a t ion .
Perform the following steps to remove memory DIMMs:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
Figu r e 4-39. Syst em Boa r d View
B2000
System Label
Power
Supply
DIMM Connectors
Figu r e 4-40. DIMM Con n ect or s on t h e Syst em Boa r d
DIMM
Connectors
(4 Slots)
114
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
2. Press downward on the ejector tabs located on both sides of the DIMM connector. See
Figure 4-41. This raises the DIMM card for easy extraction.
Figu r e 4-41. R em ovin g Mem or y Ca r d s
Ejector Tab
Ejector Tab
3. Lift up evenly on the outside edges of the DIMM card to remove it. See Figure 4-41.
4. Reinstall the remaining DIMM cards in the correct order by following the instructions
in the next section, “Replacing or Installing Additional Memory DIMMs.” Refer to
Figure 4-43 or the B2000 system label located on the chassis floor for the proper
loading sequence for the DIMM cards.
5. Close the left side panel of the workstation as explained in the section “Closing the Left
Side Panel” and plug the workstation’s power cord into the electrical outlet.
6. Verify that the reinstallation of the remaining DIMM cards was successful by following
the steps in the section “Displaying the Current Memory Configuration” on page 156.
Rep la cin g or In st a llin g Ad d it ion a l Mem or y DIMMs
Before continuing with this section, carefully read the following list of considerations:
•
Use the procedure described in “Displaying the Current Memory Configuration” on
page 156 before attempting to install additional memory DIMMs in the workstation.
•
•
Review the steps involved in installing DIMMs before you begin.
Insert DIMMs in the order shown in Figure 4-43 or in the B2000 system label located on
the floor of the workstation chassis.
•
•
Note the proper orientation for DIMMs when inserting them into their connectors.
Use the Boot Console Handler to verify that the system recognizes the additional
DIMMs when you have finished installation.
WARNING
Pow er off t h e w or k st a t ion a n d u n p lu g t h e p ow er cor d b efor e
r ep la cin g or in st a llin g a d d it ion a l m em or y DIMMs.
Chapter 4
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Perform the following steps to replace or install additional memory DIMMs:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
Figu r e 4-42. Syst em Boa r d View
B2000
System Label
Power
Supply
DIMM connectors
2. Position the workstation so that the DIMM connectors on the system board face you, as
shown in Figure 4-43. Note that Figure 4-43 also shows the loading sequence for the
DIMM cards. This loading sequence must be maintained when you install the DIMM
cards, but the size of the DIMM card put in each slot can vary. For example, you can
install a 256 MB card before a 512 MB card, and then follow the installation of the
512 MB card with another 256 MB card. The B2000 workstation supports 128 MB,
256 MB, and 512 MB DIMM cards.
Figu r e 4-43. Mem or y Slot Nu m b er s a n d Loa d in g Seq u en ce
Load 1st
SL0
Memory Slots
(4 Slots)
SL3
SL1
SL2
Load 4th
Load 2nd
Load 3rd
116
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
3. Load the DIMM cards in the memory slots using the loading sequence provided in
Figure 4-43. Note that the B2000 system label located on the chassis floor also explains
the loading sequence for DIMM cards. See Figure 4-44. Follow the steps in Figure 4-45
to install each DIMM card.
NOTE
When installing memory, you need to orient the notches on the bottom
edge of the DIMM card so that they are aligned with the keys on the DIMM
connector. See Figure 4-45. The keyed DIMM connectors prevent you from
installing the DIMM cards backwards.
Figu r e 4-44. B2000 Syst em La bel
Front of the
Workstation
Memory Loading Sequence on
B2000 System Label
Figu r e 4-45. In st a llin g a DIMM Ca r d
Press down on the ejector tabs
to open them and place the
Step 1
DIMM card in the connector
with your fingers on the edge
of the DIMM card. Be sure the
notches on the bottom edge of the
DIMM card aligns with the keys
on the DIMM connector.
Notches
Step 2
Push the DIMM card down
firmly and evenly into the
connector to be sure it is
properly seated.
Ejector Tab
Ejector Tab
Chapter 4
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
NOTE
The ejector tabs will return to the locked position when the DIMM card is
fully seated in the connector.
4. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel” and plug the workstation’s power cord into the electrical outlet.
5. Verify that this installation was successful by following the steps in the section
“Displaying the Current Memory Configuration” on page 156.
118
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Pow er Su p p ly
This section explains how to remove and replace the power supply in the B2000
workstation.
Rem ovin g t h e P ow er Su p p ly
WARNING
To p r even t in ju r y, u n p lu g t h e w or k st a t ion ’s p ow er cor d fr om t h e
elect r ica l ou t let befor e r em ovin g t h e p ow er su p p ly.
Perform the following steps to remove the power supply:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Unplug the three power supply cables from the system board.
3. Remove the rear cover of the CD drive bay and disconnect the power cable. To do this,
see the section “Removing and Replacing a CD Drive” on page 91.
4. Remove the rear cover of the floppy disk drive bay and disconnect the power cable, if the
optional floppy disk drive is installed. To do this, see the section “Removing a Floppy
Disk Drive” on page 96.
5. Detach the bundled power cables from the cable management clips on the chassis floor.
See Figure 4-46.
Figu r e 4-46. Scr ew s H old in g t h e Pow er Su p p ly in P la ce
Four T-15
Torx Screws
Cable Management Clips
Power Supply
6. Remove the four T-15 Torx screws from the rear of the chassis that hold the power
supply in place, as shown in Figure 4-46.
7. Slide the power supply towards the front of the workstation. You must disengage the
hook on the bottom of the power supply from the support strap in the chassis floor. Then
remove the power supply from the workstation chassis.
Chapter 4
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Rep la cin g t h e P ow er Su p p ly
WARNING
To p r even t in ju r y, u n p lu g t h e w or k st a t ion ’s p ow er cor d fr om t h e
elect r ica l ou t let b efor e r ep la cin g t h e p ow er su p p ly.
Perform the following steps to replace the power supply:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Place the power supply on the floor of the workstation chassis. The power supply must
be positioned such that its fan is pointing left toward the rear of the workstation, and
its cabling is coming out of the bottom, right side of the power supply.
3. Slide the power supply towards the rear of the workstation. You must engage the hook
on the bottom of the power supply into the support strap in the chassis floor.
4. Screw in the four T-15 Torx screws that hold the power supply in place into the rear of
the chassis, as shown in Figure 4-46.
5. Reattach the bundled power cables in the cable management clips on the chassis floor.
See Figure 4-46.
6. Connect the power cable to the rear of the floppy disk drive, if the optional floppy disk
drive is installed. Then replace the cover of the floppy disk drive bay. To do this, see
“Replacing or Installing a Floppy Disk Drive” on page 99.
7. Connect the power cable to the rear of the CD drive and then replace the cover of the
floppy disk drive bay. To do this, see “Removing and Replacing a CD Drive” on page 91.
8. Plug the two power supply cables into the system board.
9. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
120
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Volta ge Regu la tor Mod u les
This section explains how to remove and replace the voltage regulator modules (master
and slave), which are connected to the system board in the B2000 workstation.
Rem ovin g a Volt a ge Regu la t or Mod u le
WARNING
To p r even t in ju r y, u n p lu g t h e w or k st a t ion ’s p ow er cor d fr om t h e
elect r ica l ou t let b efor e r em ovin g t h e volt a ge r egu la t or m od u les.
Perform the following steps to remove a voltage regulator module:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Remove the four T-15 Torx screws from the rear of the chassis that hold the power
supply in place, as shown in Figure 4-47.
Figu r e 4-47. Scr ew s H old in g t h e Pow er Su p p ly in P la ce
Four T-15
Torx Screws
Power Supply
NOTE
The two voltage regulator modules are connected to the bottom of the system
board, behind the power supply. So, in the next step, you must move the
power supply to the right in order to access the voltage regulator modules.
Note that you do not need to disconnect the power supply’s cables from the
system board, nor remove the power supply entirely from the workstation
chassis in order to access the voltage regulator modules.
3. Slide the power supply to the right, towards the front of the workstation, until the hook
on the bottom of the power supply disengages from the support strap in the chassis
floor. (You do not need to disconnect the power supply’s power cables from the system
board, nor remove the power supply entirely from the workstation chassis.)
Chapter 4
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
As shown in Figure 4-48, the top voltage regulator module is the master, and the bottom
one nearest the chassis floor is the slave.
Figu r e 4-48. Th e Volt a ge R egu la t or Mod u les
Voltage Regulator
Modules:
Master (Top)
Slave (Bottom)
4. Press down on the ejector tabs located on each side of the voltage regulator module
(master or slave) to release it from the system board connector.
5. Grasp the voltage regulator module (master or slave) firmly and pull outward to release
it from the system board connector.
Rep la cin g a Volt a ge Regu la t or Mod u le
WARNING
To p r even t in ju r y, u n p lu g t h e w or k st a t ion ’s p ow er cor d fr om t h e
elect r ica l ou t let b efor e r ep la cin g a volt a ge r egu la t or m od u le.
Before replacing a voltage regulator module, ensure that it is the correct one (master or
slave) for insertion into the correct connector on the system board. See Figure 4-49 to
identify the two different voltage regulator modules (master and slave).
NOTE
The master and the slave voltage regulator modules differ in the placement of
the notch in their gold edge connectors, as shown in Figure 4-49. This notch
fits the notch-key of the system board’s connector into which each voltage
regulator module (master or slave) fits. The notches and notch-keys prevent
you from installing a voltage regulator module into the wrong connector.
Refer to Figure 4-48 for the correct system board connector (the top connector for the
master, or the bottom connector nearest the chassis floor for the slave) in which to insert
the voltage regulator module you need to replace.
122
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Figu r e 4-49. Ma st er a n d Sla ve Volt a ge R egu la t or Mod u les
Notch
Master
Notch
Slave
Perform the following steps to replace a voltage regulator module:
1. Press down on the ejector tabs on either side of the system board connector to open
them. Be sure that you will be inserting the voltage regulator module into the correct
system board connector (the top connector if it is a master voltage regulator module, or
the bottom connector nearest the chassis floor if it is a slave).
2. Orient the notch on the gold edge of the voltage regulator module so that it aligns with
the notch-key in the system board connector. Push the voltage regulator module into the
correct system board connector (the top connector if it is a master voltage regulator
module, or the bottom connector nearest the chassis floor if it is a slave) until the
voltage regulator module is seated entirely in the connector.
NOTE
The ejector tabs will return to the locked position when the voltage regulator
module is fully seated in the connector.
3. Slide the power supply towards the rear of the workstation. You must engage the hook
on the bottom of the power supply into the support strap in the chassis floor.
4. Screw in the four T-15 Torx screws that hold the power supply in place into the rear of
the chassis. See Figure 4-47.
5. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
Chapter 4
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Fa n s
The B2000 has three fans, which are shown in Figure 4-50: I/O fan, system fan, and
processor (turbocooler) fan. A chassis code in the workstation’s LCD which indicates that a
fan has failed (FLT D01n) or is running too slowly (WRN D02n) within a B2000 workstation
specifies the fan number, n. Figure 4-50 notes the number (n) for each fan. For more
information on identifying either a fan that has failed or one that is running too slowly, see
“Fan Faults and Warnings” on page 48.
NOTE
The processor fan (5) is mounted to the processor substrate on the system
board tray assembly. Thus, the processor fan itself is not replaceable. If the
LCD indicates a processor fan failure (FLT D015), the entire system board
tray assembly must be replaced. In this case, follow the procedures for
removing and replacing the system board tray assembly starting on page 129.
Figu r e 4-50. Fa n Loca t ion s
I/O Fan (2)
System
Fan (4)
Processor
Fan (5)
If either the I/O fan (2) or the system fan (4) fails, you will need to replace it to ensure no
heat damage is caused to the workstation. To remove and replace the fan, see the following
subsections for the I/O fan or the system fan, as appropriate.
Rem ovin g t h e I/O Fa n
NOTE
The speaker is contained within the same mounting bracket as the I/O fan.
For instructions on how to remove and replace the speaker, see page 127.
Perform the following steps to remove the I/O fan:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Remove the PCI retainer clip and all I/O cards. See the section “Removing I/O Cards” on
page 111.
124
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
3. Unscrew the two T-15 Torx screws that hold the workstation’s air divider in place, as
shown in Figure 4-51. Then grasp the edge of the air divider and pull it towards you to
remove it from the workstation.
Figu r e 4-51. R em ovin g t h e Air Divid er
T-15 Torx
Screw
T-15 Torx
Screw
Air Divider
4. Disconnect the I/O fan and speaker cables from the system board.
5. Lift up on the fan/speaker mounting bracket tab from the hole in the drive bay housing.
Then rotate the mounting bracket toward the chassis wall and rotate the fan/speaker
mounting bracket out of the chassis.
6. Remove the I/O fan from the mounting bracket by slightly pulling the left and right fan
mounting clips away from the fan, and then pulling the fan outward. See Figure 4-52.
Figu r e 4-52. R em ovin g t h e I/O Fa n fr om t h e Br a ck et
I/O Fan
I/O Fan/Speaker
Mounting Bracket
Fan
Mounting
Speaker
Clip
Fan
Mounting
Clip
Chapter 4
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Rep la cin g t h e I/O Fa n
Perform the following steps to replace the I/O fan:
1. Install the I/O fan into the fan/speaker mounting bracket by pulling out on the left and
right fan mounting clips, inserting the fan, and then releasing the fan mounting clips so
that they hold the fan in place. See Figure 4-52.
2. Align the fan/speaker mounting bracket in the chassis, holding the fan and speaker
cable to the card guide edge of the mounting bracket. Then rotate the fan/speaker
mounting bracket into place while holding up on the retainer tab.
3. Connect the I/O fan and speaker cables to the system board.
4. Place the air divider within the chassis and screw in the two T-15 Torx screws that hold
the air divider in place. See Figure 4-51.
5. Replace all I/O cards and the PCI retainer clip as explained in the section “Replacing or
Installing I/O Cards” on page 112.
6. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
Rem ovin g t h e Syst em Fa n
Perform the following steps to remove the system fan:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Remove the four plastic pop rivets at the corners of the system fan to release the fan
from the rear panel of the workstation chassis.
3. Disconnect the system fan’s power cable from the system board and remove the fan.
Rep la cin g t h e Syst em Fa n
Perform the following steps to replace the system fan:
1. Align the flow arrow on the system fan so that it is pointing toward the rear panel of the
workstation chassis.
2. Position the fan flush with the rear panel of the workstation and insert the four plastic
pop rivets to secure the fan to the rear panel.
3. Connect the system fan’s power cable to the system board.
4. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
126
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
Sp ea k er
This section explains how to remove and replace the speaker in the B2000 workstation.
The speaker is contained in the mounting bracket with the I/O fan. See Figure 4-53.
Figu r e 4-53. Loca t ion of t h e Sp ea k er
Speaker
Rem ovin g t h e Sp ea k er
Perform the following steps to remove the speaker:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Remove the PCI retainer clip and all I/O cards. See the section “Removing I/O Cards” on
page 111.
3. Unscrew the two T-15 Torx screws that hold the workstation’s air divider in place, as
shown in Figure 4-54. Then grasp the edge of the air divider and pull it towards you to
remove it from the workstation.
Figu r e 4-54. R em ovin g t h e Air Divid er
T-15 Torx
Screw
T-15 Torx
Screw
Air Divider
Chapter 4
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
4. Disconnect the speaker and I/O fan cables from the system board.
5. Lift up on the fan/speaker mounting bracket tab from the hole in the drive bay housing.
Then rotate the mounting bracket toward the chassis wall and rotate the fan/speaker
mounting bracket out of the chassis.
6. Remove the speaker from the mounting bracket by inserting a finger through the access
hole and pushing on the speaker until it pops free from the mounting clips on the fan/
speaker mounting bracket. See Figure 4-55.
Figu r e 4-55. R em ovin g t h e Sp ea k er fr om t h e Mou n t in g Br a ck et
Speaker
Mounting
Clip
I/O Fan/Speaker
Mounting Bracket
I/O Fan
Speaker
Cable
Speaker
Speaker
Mounting
Clip
7. Remove the speaker cable from the cable clips and slide the speaker cable out of the
notched hole in the fan/speaker mounting bracket.
Rep la cin g th e Sp ea k er
Perform the following steps to replace the speaker:
1. Position the speaker so that the speaker cable runs out of the hole in the rear of the I/O
fan/speaker mounting bracket. Note that the speaker cable must be held in place on the
backside of the mounting bracket by the speaker cable clips.
2. Pull outward on the speaker mounting clips and put the speaker in place. Then release
the mounting clips so that they hold the speaker in the mounting bracket.
3. Align the fan/speaker mounting bracket in the chassis, holding the fan and speaker
cable to the card guide edge of the mounting bracket. Then rotate the fan/speaker
mounting bracket into place while holding up on the retainer tab.
4. Connect the speaker and I/O fan cables to the system board.
5. Place the air divider within the chassis and screw in the two T-15 Torx screws that hold
the air divider in place. See Figure 4-54.
6. Replace all I/O cards and the PCI retainer clip as explained in the section “Replacing or
Installing I/O Cards” on page 112.
7. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
128
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
System Boa r d Tr a y Assem bly
The system board contains the CPU, main memory, I/O section, and all of the circuitry and
connections that control how the workstation’s hardware and operating system interact
with each other. If any of the components on the system board are defective, you must
remove and replace the system board.
Because the system board in the B2000 workstation is mounted on a tray, the following
procedures explain how to remove and replace the system board tray assembly as a
complete unit.
Rem ovin g t h e Syst em Boa r d Tr a y Assem b ly
Perform the following steps to remove the system board tray assembly:
1. Open the left side panel of the workstation as shown in the section “Opening the Left
Side Panel.”
2. Remove the following internal components from the workstation:
a. Hard disk drive(s) and bracket(s), as shown in the section “Removing a Hard Disk
Drive” on page 104.
b. PCI retainer clip and all I/O cards, as shown in the section “Removing I/O Cards” on
page 111.
c. All memory DIMM cards, as shown in the section “Removing Memory DIMMs” on
page 114.
d. Power supply, as shown in the section “Removing the Power Supply” on page 119.
e. Both the master and slave voltage regulator modules, as shown in the section
“Removing a Voltage Regulator Module” on page 121.
f. Air divider, as shown in Step 3 of the section “Removing the I/O Fan” on page 125.
3. Disconnect all cables from the system board, including the following:
a. CD drive data and audio cables
b. Floppy disk drive data cable
c. I/O fan and speaker cables
d. System fan cable
e. LCD ribbon cable
4. Fold back all of the cables to avoid interference or damage when removing the system
board tray assembly from the workstation chassis.
Chapter 4
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
5. Remove the two T-15 Torx screws that secure the system board tray assembly to the
rear panel of the workstation chassis. See Figure 4-56.
Figu r e 4-56. Scr ew s H old in g t h e Syst em Boa r d Tr a y Assem b ly in P la ce
Two T-15
Torx Screws
6. Grasp the system board tray assembly and slide the system board tray assembly toward
the front of the workstation. The keyholes in the system board tray assembly are
unlatched from the chassis wall hooks.
7. Tilt the system board tray assembly up, rotate it clockwise, and lift it out of the chassis.
Rep la cin g t h e Syst em Boa r d Tr a y Assem b ly
Perform the following steps to replace the system board tray assembly:
1. Fold back all cables to avoid interference or damage when installing the system board
tray assembly in the workstation chassis.
2. Angle the system board tray assembly diagonally as you begin to put it into the
workstation chassis. Then position it flat inside the chassis, against the chassis wall.
3. Slide the system board tray assembly slightly to the front and then to the rear of the
workstation to engage the chassis wall hooks into the keyholes.
4. Screw in the two T-15 Torx screws that secure the system board tray assembly to the
rear panel of the workstation chassis. See Figure 4-56.
5. Connect all cables to the system board, including the following:
a. CD drive data and audio cables
b. Floppy disk drive data cable
c. I/O fan and speaker cables
130
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
d. System fan cable
e. LCD ribbon cable
6. Replace the following internal components in the workstation:
a. Hard disk drive(s) and bracket(s), as shown in the section “Replacing or Installing a
Hard Disk Drive” on page 107.
b. All I/O cards and the PCI retainer clip, as shown in the section “Replacing or
Installing I/O Cards” on page 112.
c. All memory DIMM cards, as shown in the section “Replacing or Installing Additional
Memory DIMMs” on page 115.
d. Both the master and slave voltage regulator modules, as shown in the section
“Replacing a Voltage Regulator Module” on page 122.
e. Power supply, as shown in the section “Replacing the Power Supply” on page 120.
f. Air divider, as shown in Step 4 of the section “Replacing the I/O Fan” on page 126.
7. Close the left side panel of the workstation as shown in the section “Closing the Left
Side Panel.”
Chapter 4
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Field Replaceable Units
FRU Removal and Replacement
132
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Block Dia gr a m
This chapter contains the functional block diagram of the HP VISUALIZE B2000
workstation.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Block Diagram
Figu r e 5-1. F u n ct ion a l Block Dia gr a m of t h e B2000 Wor k st a t ion
134
Chapter5
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Boot Con sole Ha n d ler
This chapter explains how to use the Boot Console Handler, which provides an interactive
environment after the power-on sequence in the HP VISUALIZE B2000 workstation.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Chapter Overview
Ch a p t er Over view
This chapter contains the following main sections:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Boot Console Handler Features
Accessing the Boot Console Handler
Booting the Workstation
Searching for Bootable Media
Resetting the Workstation
Displaying and Setting Paths
Displaying and Setting the Monitor Type
Displaying the Current Memory Configuration
Displaying the Status of the I/O Slots
Setting the Auto Boot and Auto Search Flags
Displaying and Setting the Security Mode
Displaying and Setting Fastboot Mode
Displaying the LAN Station Address
Displaying System Information
Displaying PIM Information
Stable Storage
ISL Environment
Obtaining and Updating System Firmware
136
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Boot Console Handler Features
Boot Con sole Ha n d ler Fea tu r es
There are times when you want to interact directly with the hardware of the B2000
workstation before it boots the operating system. The B2000 workstation provides a
menu-driven Boot Console Handler that allows you to perform special tasks, display
information, and set certain system parameters, even if the operating system is
unavailable.
Here are some of the things you can do:
•
•
•
•
•
•
•
•
•
•
•
Boot the system
Search for bootable media
Reset the system
Display and set boot paths
Display and set the monitor type
Display memory configuration information
Display the status of the PCI slots
Set Auto Boot, Auto Search, and Auto Start
Set Fastboot
Display LAN information
Display system information
The Boot Console Handler menus follow, showing the various tasks you can perform and
the available information. The shortened version of each command is indicated by the
uppercase letters.
Help is available for all the menus and commands by using either help, he, or ?and the
menu or command for which you want help.
Chapter 6
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Boot Console Handler Features
-------------- Main Menu --------------------------------------
Command
Description
-----------
-----------
BOot [PRI|ALT|<path>]
Boot from specified path
PAth [PRI|ALT|CON|KEY|[<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
COnfiguration [<command>]
INformation [<command>]
SERvice [<command>]
Access Configuration menu/commands
Access Information menu/commands
Access Service menu/commands
DIsplay
HElp [<menu>|<commands>]
RESET
Redisplay the current menu
Display help for menu or command
Restart the system
-----
Main Menu: Enter command >
138
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Boot Console Handler Features
------ Configuration Menu -----------------------------
Command
-------
Description
-----------
AUto [BOot|SEArch] [ON|OFF]
BootID [<proc>] [<boot ID>]
BootINfo
BootTimer [0 - 200]
CPUconfig [<proc>] [ON|OFF]
DEfault
FastBoot [ON|OFF]
LanConfig
MOnitor [LIST|<path> <type>]
Display or set specified auto flag
Display or modify processor boot ID
Display boot-related information
Seconds allowed for boot attempt
Config/deconfig processor
Set the system to predefined values
Display or set boot tests execution
Display or set LAN Configuration
Change the current monitor type
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
SECure [ON|OFF]
Set/show security mode
TIme [c:y:m:d:h:m:s]
PreviousPower [ON|OFF]
Read or set real time clock in GMT
Set previous power state
BOot [<menu>|<command>]
DIsplay
HElp [<menu>|<command>]
RESET
MAin
Boot from specified path
Redisplay the current menu
Display help for menu or command
Restart the system
Return to Main Menu
-----
Configuration Menu: Enter command >
Chapter 6
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Boot Console Handler Features
------ Information Menu -------------------------------
Command
-------
Description
-----------
ALL
BootINfo
CAche
Display all system information
Display boot-related information
Display cache information
ChipRevisions
COprocessor
FwrVersion
IO
LanAddress
MEmory
Display revisions of VLSI and firmware
Display coprocessor information
Display firmware version
Display I/O interface information
Display built-in system LAN address
Display memory information
PRocessor
SysConfig
WArnings
Display processor information
Display the system configuration
Display selftest warning messages
BOot [PRI|ALT|<path>]
DIsplay
HElp [<menu>|<command>]
RESET
MAin
Boot from specified path
Redisplay the current menu
Display help for menu or command
Restart the system
Return to Main Menu
------
Information Menu: Enter command >
140
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Boot Console Handler Features
------ Service Menu -----------------------------------
Command
-------
Description
-----------
ChassisCodes[<proc>|ON|OFF
CLEARPIM
EepromRead [<addr>] {<len>}
Display/enable/disable chassis codes
Clear (zero) the contents of PIM
Read EEPROM locations
MemRead <addr> [<len>] [<type>] Read memory locations
PCIDelay [<value>]
PDT [CLEAR]
Display or set PCI delay value
Display or clear
the Page Deallocation Table
Display PIM information
Display or change scrolling ability
PIM [<proc> [HPMC|LPMC|TOC]]
ScRoll [ON|OFF]
BOot [PRI|ALT|<path>]
DIsplay
HElp [<menu>|<command>]
RESET
Boot from specified path
Redisplay the current menu
Display help for menu or command
Restart the system
MAin
Return to Main Menu
-----
Service Menu: Enter command >
Chapter 6
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Accessing the Boot Console Handler
Accessin g th e Boot Con sole Ha n d ler
If the workstation has crashed or power was turned off for some reason, press the power
switch and proceed to step 3. Otherwise, to access the Boot Console Handler, follow these
steps:
NOTE
This procedure should be done by a system administrator or superuser with
rootlogin permissions.
1. Close any files and applications on the workstation.
2. Press the power switch on the front panel of the workstation.
NOTE
There is no need to login as rootand execute the shutdown-qcommand to
shut down the HP-UX operating system on the workstation before powering it
off. When you turn off the power switch, the workstation automatically shuts
down the operating system before terminating the power.
Make sure you do not unplug the system’s power cord or otherwise interrupt power to
the workstation at this time.
When the operating system has been properly shut down, the following message will
appear:
Shutdown complete
3. Power on the workstation after the system has completely shut down.
If autobootis turned off, the boot sequence automatically stops at the Boot Console
Handler’s Main Menu.
If autobootis turned on, you will see the following message:
Processor is starting auto boot process. To
discontinue, press any key within 10 seconds.
142
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Accessing the Boot Console Handler
If autobootand autosearchare both turned on, you will see the following message:
Processor is booting from first available de-
vice. To discontinue, press any key within 10
seconds.
NOTE
If you are using a power-saving monitor, you will have less than 10 seconds
from the time this message appears to press a key.
4. Press a key. You will then see the message:
Boot terminated
The Main Menu of the Boot Console Handler appears.
Chapter 6
143
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Booting the Workstation
Bootin g th e Wor k sta tion
You usually start the system by turning it on and waiting for HP-UX to boot automatically.
However, you may not always want the usual boot sequence to occur.
For example, you may want to start the system from an operating system that is stored on
a device that is different from the usual boot device. If the normal operating system kernel
or the disk on which it resides becomes damaged or unusable, you may wish to boot from a
different disk or perhaps another type of device, such as a CD drive.
Here are some possible booting scenarios you may encounter:
•
If you know which device you want to boot from, and you know that it contains a
bootable operating system, follow the directions in “Accessing the Boot Console
Handler” earlier in this chapter, and then type the following at the prompt:
Main Menu: Enter command > boot device
where deviceis the hardware path to the device, specified in Mnemonic Style
Notation. For example, if you wish to boot an operating system that is stored on a
DDS-format tape drive that is located at the hardware path scsi.1.0, you would type
the following command at the prompt and press Enter:
Main Menu: Enter command > boot scsi.1.0
•
If you do not know which device or the hardware path for the device you want to boot
from, then type the following at the prompt and press Enter:
Main Menu: Enter command > search
A message similar to the following will be displayed:
Path Number Device Path
Device Type
----------- ---------------- -----------
P0
P1
IDE
SCSI.6.0
TEAC CD-532E-B
SEAGATE ST39102LC
At the prompt, you might type the following and press Enter:
Main Menu: Enter command > boot P1
Note that the operating system on the specified device (P1) is used to boot the system
(also see the section “Searching for Bootable Media”).
144
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Booting the Workstation
•
If you wish to interact with the Initial System Loader (ISL) before booting the system,
follow the directions in “Accessing the Boot Console Handler” earlier in this chapter,
and then type the following at the prompt:
Main Menu: Enter command > boot device
The following prompt will appear:
Interact with ISL (Y,N,Q)>
Answering yes (Y) causes the ISL to be loaded from the specified device. After a short
time, the following prompt appears on the screen:
ISL>
ISL is the program that actually controls the loading of the operating system. By
interacting with ISL, you can choose to load an alternate version of the HP-UX
operating system. If you do not want to interact with ISL, you must enter no (N).
For example, if the usual kernel (/stand/vmunix) on the root disk (scsi.6.0) has
become corrupted, and you wish to boot the system from the backup kernel
(/stand/vmunix.prev), type the following at the ISL>prompt and press Enter:
ISL> hpux /stand/vmunix.prev
•
If you do not know which media in the file systems have bootable operating systems,
you can find them with the searchiplcommand. See the next section, “Searching for
Bootable Media.”
Chapter 6
145
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Searching for Bootable Media
Sea r ch in g for Boota ble Med ia
To list devices that contain bootable media, follow the directions in “Accessing the Boot
Console Handler” earlier in this chapter, and then type the following at the prompt and
press Enter:
Main Menu: Enter command> search ipl
The search command searches all buses. The search may turn up more devices than there
are lines on the display. If you are using a text terminal, you may control the progress of
the search from the terminal’s keyboard by using these keystrokes:
Ctrl S
Ctrl Q
Temporarily suspends the search.
Continues the search.
Any Other Key Stops the search.
These flow-control keystrokes do not work with a bitmapped display, but such a display
can show more than forty lines of text, so you are unlikely to need them.
To search for devices of just one type that actually contain bootable media, follow the
directions in “Accessing the Boot Console Handler” earlier in this chapter, and then type
the following at the prompt and press Enter:
Main Menu: Enter command> search ipl device_type
where device_typeis one of the following:
scsi
lan
Is the built-in Ultra2 Wide LVD SCSI bus.
Is all connections to the built-in LAN.
pcin
ide
Is an optional plug-in device in PCI slot number n.
Is the built-in IDE bus.
disk
Is all connections except LAN (for example, PCI cards, etc.)
146
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Resetting the Workstation
Resettin g t h e Wor k st a tion
To reset the system to its predefined values, follow the directions in “Accessing the Boot
Console Handler” earlier in this chapter, and then type the following at the prompt and
press Enter:
Main Menu: Enter command> co
When the Configuration Menu appears, type the following at the prompt and press Enter:
Configuration Menu: Enter command> default
When the Configuration Menu appears again, type the following at the prompt and press
Enter:
Configuration Menu: Enter command> reset
Chapter 6
147
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting Paths
Disp la yin g a n d Set tin g Pa t h s
A path is the hardware address of a device that is attached to the I/O system of the system.
The pathcommand sets the system paths shown in Table 6-1.
The pathcommand sets and displays the hardware address of a specified device attached
to the I/O bus of the system.
Ta b le 6-1. Syst em Pa t h s
Path Type
Device
primary or pri
alternate or alt
console or con
keyboard or key
Default boot device (usually the root disk)
Alternate boot device (usually a DDS-format tape device)
Primary display device
Primary input ASCII device
To display the current settings for the system paths, type the following at the prompt and
press Enter:
Main Menu: Enter command> path
The paths are displayed in Mnemonic Style Notation, as shown in Table 6-2.
Ta b le 6-2. Mn em on ic St yle Not a t ion for Boot Pa t h s
I/O Type
Specification Format
Built-in LVD SCSI scsi.scsi_address.logical_unit_number
Plug-in device
Built-in LAN
Built-in IDE
pcin.scsi_address.logical_unit_number
lan.server_address.init_timeout.io_timeout
ide
To display the current setting for a particular system path, follow the directions in
“Accessing the Boot Console Handler” earlier in this chapter, and then type the following at
the prompt and press Enter:
Main Menu: Enter command> path path_type
where path_typeis one of the path types listed in Table 6-1.
For example, to get the path to the primary boot device, follow the directions in “Accessing
the Boot Console Handler” earlier in this chapter, and then type the following at the
prompt and press Enter:
Main Menu: Enter command> path primary
148
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting Paths
To set a system path to a new value, follow the directions in “Accessing the Boot Console
Handler” earlier in this chapter, and then type the following at the prompt and press Enter:
Main Menu: Enter command> path path_type path
where path_typeis one of the path types listed in Table 6-1 and pathis the specification of
the path in Mnemonic Style Notation (as described in Table 6-2). For example, to set the
primary boot path to a SCSI disk with ID of 6.0, follow the directions in “Accessing the
Boot Console Handler” earlier in this chapter, and then type the following at the prompt
and press Enter:
Main Menu: Enter command> path pri scsi.6.0
NOTE
The default B2000 paths are:
pri scsi.6.0
alt scsi.5.0
Chapter 6
149
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting the Monitor Type
Disp la yin g a n d Set tin g th e Mon it or Typ e
The workstation ships from the factory preset to use a monitor with a specific resolution
and frequency. If you replace the workstation’s monitor with a different type of monitor,
you may have to reconfigure the system to support the new monitor.
Th e Mon itor Com m a n d
The monitorcommand lets you change the system’s graphics configuration. This command
is available in the Configuration Menu of the Boot Console Handler.
NOTE
The monitorcommand lets you change the system’s graphics configuration
before you replace a workstation’s monitor. For information about changing
the configuration after you replace a monitor, refer to “Changing the Monitor
Type” in Chapter 4.
To display the current graphics and console information, type the following set of
commands and press Enter at the prompt:
Main Menu: Enter command> configuration
Configuration Menu: Enter command> monitor
The correct usage for setting the graphics configuration is:
monitor graphics_path type
where valid graphics_pathparameters are:
graphics(0) Built-in (or core) graphics adapter (primary slot)
graphics(1) Graphics adapter installed in slot 1 (secondary slot)
graphics(2) Graphics adapter installed in slot 2
graphics(3) Graphics adapter installed in slot 3
graphics(4) Graphics adapter installed in slot 4
and typeis the numerical monitor type. See “Setting the Monitor Type” in a subsequent
section for a list of types. For example, an HP VISUALIZE-fxe graphics card (A4982A)
installed in option slot 2 would be graphics(2). Note that you can have graphics(0)
through graphics(4)for the graphics_path.
150
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting the Monitor Type
Disp la yin g th e Cu r r en t Mon itor Con figu r a tion
To display the current monitor configuration for the system from the Configuration Menu
of the Boot Console Handler, follow the directions in “Accessing the Boot Console Handler”
earlier in this chapter. Once you are in the Boot Console Handler Main Menu, type the
following command and press Enter:
Main Menu: Enter command> configuration
This places you in the Configuration Menu. From here, type the following command at the
prompt and press Enter:
Configuration Menu: Enter command> monitor
The message on the display is a list of the current graphics adapters and their monitor
types configured for the workstation.
MONITOR INFORMATION
Path
---------- --- --- ------- ---------- ---- --- ---
GRAPHICS(2) 2 1 fffa000000 1280x1024 75Hz 1 PCI
Slot Head HPA
Resolution Freq Type Class
Configuration Menu: Enter command>
In this example, only the graphics adapter (located in slot 2) GRAPHICS(2)is configured.
The monitor type for GRAPHICS(2)is set to type 1, which is a 1280×1024 monitor that uses
a frequency of 75 Hz.
Settin g th e Mon it or Typ e
You can set the monitor type for a graphics adapter by typing the following at the prompt
and pressing Enter:
Configuration Menu: Enter command> monitor graphics(n) tt
where nis the number of the graphics adapter and ttis the monitor type. To display a list
of supported monitors that are used by the graphics card, type the following command at
the prompt and press Enter:
Configuration Menu: Enter command> monitor list
A list of valid monitor types similar to the following is displayed:
MONITOR INFORMATION
Path
----
Slot Head Type
---- ---- ---- --------- ---- -----
Size
Freq Class
GRAPHICS(0) 0
GRAPHICS(0) 0
GRAPHICS(0) 0
GRAPHICS(0) 0
1
1
1
1
1 1280x1024 75Hz VESA
2 1024x768 75Hz VESA
3 1600x1200 75Hz VESA
4 1600x1200 75Hz VESA
Chapter 6
151
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting the Monitor Type
To set the monitor type for GRAPHICS(2)to monitor type 1, type the following at the
command prompt and press Enter:
Configuration Menu: Enter command> monitor graphics(2) 1
This will take effect on the next reboot or reset of the system.
MONITOR INFORMATION
Path
---------- --- --- ------- ---------- ---- --- ---
GRAPHICS(0) 0 1 fffa000000 1280x1024 75Hz 1 VESA
Slot Head HPA
Resolution Freq Type Class
Configuration Menu: Enter command>
The Boot Console Handler displays a message that tells you that the new monitor selection
will take effect the next time you reboot the system. The Boot Console Handler also
displays the new monitor information.
Trying to change the monitor type to a number not listed for that graphics device fails and
gives you the following warning message:
Value of monitor type n out of range (n - nn)
Trying to change the monitor type on an empty slot fails and gives you the following
warning message:
No such graphics card.
Settin g th e Mon it or Typ e w ith SAM
The System Administration Manager (SAM) allows you to change the monitor type after
the HP-UX 10.20 operating system with the 9912 Additional Core Enhancements (ACE)
software bundle (December 1999) have been installed on the workstation. This section
provides a brief explanation on how to set the monitor type using SAM. Note that you will
need to be logged in as rootto run SAM.
Here are the steps for setting the monitor type with SAM:
1. Log in as root.
2. Move the mouse pointer to the Ap p lica t ion Ma n a ger control for tools and click the left
mouse button. Alternatively you can execute sam at a terminal window command
prompt and skip to step 5.
152
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting the Monitor Type
3. Double-click on the Syst em _Ad m in icon in the Ap p lica t ion Ma n a ger window.
4. Double-click on the Sam icon in the Ap p lica t ion Ma n a ger -- Syst em _Ad m in window.
If you are root, the Syst em Ap p lica t ion Ma n a ger (SAM) will appear on the screen.
5. Double-click on the Disp la y icon.
6. Double-click on the Mon it or Con figu r a t ion icon in the Disp la y window.
The Mon it or Con figu r a t ion window will have a monitor icon(s) in it that is/are
associated with the graphics card(s) in the workstation’s I/O card slot(s).
7. Click on the monitor icon in the Mon it or Con figu r a t ion window whose monitor type
you want to set.
Chapter 6
153
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting the Monitor Type
8. Select the action Mod ify Mon it or Typ e from the Action s menu. You will see a
window with a list of monitor type selections in it. Here is an example of a monitor type
entry you may see:
Entry Width Height Hz Font Description
1
1280
1024
75 10x20
VESA
9. Select an entry from the list in the Mod ify Mon it or window. In that same window,
select the check box labeled Ma k e m on it or t yp e ‘n ’ t h e d efa u lt where n is the
number of the entry you selected. To finish the monitor type selection, select the
Mod ify Mon it or window’s OK button. A pop-up window will appear to confirm the
monitor type selection. Press the Yes button in that pop-up window. This causes the
monitor to reset, possibly hiding existing windows. You will then be given 15 seconds
after the monitor type changes to configure this setting. Press the OK button to
configure the setting. This completes the process for setting the monitor type. Note that
this change takes effect immediately.
10.Connect the monitor cable to the graphics card you selected, and the screen contents
will appear. You are now done selecting the monitor type.
Settin g th e Mon it or Typ e a t Pow er On
If you replace the workstation’s monitor with a different monitor type, you need to let the
workstation’s firmware know you made this change. To do this, reboot the system and use
either the automatic monitor selection process or the Boot Console Handler’s monitor
command. The monitor command is described in the section “Setting the Monitor Type” in
this chapter. The automatic monitor selection process is described in this section.
Once you have rebooted the system by turning it off, wait for a short time for the hard disk
drive’s disk to stop spinning. Next, turn the workstation on and watch for the Num Lock
light to come on.
NOTE
It takes a short amount of time (approximately 40 seconds) after powering on
the workstation before the Num Lock light comes on.
Wait two seconds after the Num Lock light comes on, which is near the end of the boot
sequence, then press Tab to initiate the automatic monitor selection process. If the screen
remains blank after two minutes of waiting for something to be displayed, see the section
“Troubleshooting Monitor Problems” in this chapter. Otherwise, if you see information
similar to the following displayed on the screen and it is the correct monitor type, press the
Enter key to select it.
Path
---------- ---- ---- ---- ------------ ---- -----
GRAPHICS(0) 0 n nnnnxnnnn nnHz VESA
Slot Head Type
Size
Freq Class
1
Press [Return] to select this monitor type (type n of n types).
Note that if you do not select this monitor type, the system cycles through a limited
number of monitor types one at a time until you find one that meets your needs.
154
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting the Monitor Type
Once you have made the monitor type selection, the system queries you to confirm the
selection. Press Y to save this monitor type.
If you press any key other than Y, the following message is displayed:
Monitor type not saved.
At this point, the new monitor type is active, but not saved. Because you did not save the
monitor type, the next time you reboot the system the original monitor type will be used.
Next, the following message is displayed:
To select a new Graphics Monitor Type press the <TAB> key now, otherwise EXIT by
entering any other key (or will time out in 15 seconds)...
To restart the monitor selection process, press Tab.
Tr ou blesh ootin g Mon itor P r oblem s
In the event that the console stops displaying to the graphics device, use the following
procedure to set the console for displaying to an external terminal.
Here are the steps to follow:
1. Turn off the workstation.
2. Disconnect the workstation’s keyboard connector from the rear panel.
3. Connect a serial terminal emulator to the Serial 1 connector (the left serial connector)
on the system rear panel. Configure the terminal for: 9600 baud, No Stop Bits, No
Parity, 8 Bits.
4. Power on the system. The system will now display the console to the terminal connected
to Serial 1 port. Note that you can use a 9-pin to 9-pin serial cable (HP F1044-80002) to
connect an HP OmniBook serial port to the workstation.
5. Set the monitor type and path using the Boot Console Handler. For information on
doing this see the section “Setting the Monitor Type with SAM.”
Chapter 6
155
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying the Current Memory Configuration
Disp la yin g th e Cu r r en t Mem or y Con figu r a tion
The following sample screen output uses the memorycommand to show a memory
configuration table with properly-installed and configured memory.
To display the current memory configuration for the system, from the Information Menu of
the Boot Console Handler, follow the directions in “Accessing the Boot Console Handler”
earlier in this chapter. Once you are in the Boot Console Handler Main Menu, type the
following at the prompt and press Enter:
Main Menu: Enter command> information
This places you in the Information Menu. From here, type the following at the prompt and
press Enter:
Information Menu: Enter command> memory
The screen displays status and configuration information for the memory DIMMs installed
in the workstation. See the section “Memory Information Sample.”
Mem or y In for m a tion Sa m p le
The following example shows the memory information when memory modules are properly
installed and configured:
MEMORY INFORMATION
MEMORY STATUS TABLE
Slot
Size
Status
---- ------ -------------
0
1
2
256MB Active
256MB Active
128MB Active
TOTAL MEMORY = 640MB
MEMORY FAULT TABLE
Slot
Size
Status
---- ------ -------------
Active, Installed Memory
Deallocated Pages
: 640MB of SDRAM
: 0 Pages
-----------
: 640MB
Available Memory
Good Memory Required by OS
:
0 (Not Initialized)
Memory
HVERSION SVERSION
-------- ----------
0x0860 0x0900
156
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying the Status of the I/O Slots
Disp la yin g th e Sta t u s of th e I/O Slots
The iocommand lets you identify all built-in I/O devices and optional I/O devices installed
in the option slots. It is available in the Information Menu.
To use the IO command from the Information Menu of the Boot Console Handler, type the
following command at the prompt and press Enter:
Information Menu: Enter command> io
Information about the built-in and optional I/O devices is displayed.
Chapter 6
157
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Setting the Auto Boot and Auto Search Flags
Settin g th e Au to Boot a n d Au to Sea r ch F la gs
The autobootand autosearchflags are variables stored in the system’s nonvolatile
memory. (Nonvolatile memory retains its contents even after power is turned off.) If you
reset these flags to new values, the change takes effect the next time you reboot the
workstation.
The autobootflag boots the operating system whenever the workstation is turned on.
If autobootis set to on, the system automatically attempts to boot the operating system
when turned on. If autobootis set to off, the system enters the boot administration mode
of the Boot Console Handler’s user interface.
The state of the autosearchflag determines how the system seeks a boot device during
auto boot. If autosearchis set to on, the system will search for other boot devices if the
primary boot device is not available. If autosearchis off, the system will default to the
boot administration mode if it can’t see the primary boot device.
To examine the state of the autobootand autosearchflags, type the following at the
prompt and press Enter:
Configuration Menu: Enter command> auto
To change the state of the auto boot or auto search flags, type the following at the prompt
and press Enter:
Configuration Menu: Enter command> auto boot state
or
Configuration Menu: Enter command> auto search state
where stateis on or off.
The autosearchcommand searches for devices in the following order:
Primary boot path (can be set by the user)
Alternate boot path (can be set by the user)
PCI 1 through PCI 4 (plug-in interface cards)
Low-voltage differential SCSI (built-in)
LAN (built-in)
IDE (built-in)
158
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting the Security Mode
Disp la yin g a n d Set tin g th e Secu r ity Mod e
The secureflag is a variable stored in non-volatile memory. (Non-volatile memory retains
its contents even after power is turned off.) If you reset this flag to a new value, the change
takes effect the next time you reboot the workstation.
When the secureflag is set to on, auto boot and auto search are enabled and cannot be
stopped. The system boots from the default boot paths regardless of user intervention.
Note that the securecommand must be executed from within the Boot Console Handler.
To get into the Boot Console Handler, follow the procedure in the section “Accessing the
Boot Console Handler” earlier in this chapter. Once the Main Menu is present, you can
type the following command at the prompt and press Enter:
Main Menu: Enter command > configuration
From the Configuration Menu, you can execute the securecommand and preform the
subsequent tasks in this section.
To display the current setting for the secureflag, type the following command at the
prompt and press Enter:
Configuration Menu: Enter command > secure
To set the secureflag on, type the following command at the prompt and press Enter:
Configuration Menu: Enter command > secure on
To set the secureflag off, you need to disconnect the boot disk to interrupt the boot-up
sequence and force the prompt to the Boot Console Handler. Next, type the following
command at the prompt and press Enter:
Configuration Menu: Enter command > secure off
Chapter 6
159
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying and Setting Fastboot Mode
Disp la yin g a n d Set tin g Fa stboot Mod e
When fastbootis enabled (set to on), the system does a quick check of the memory and
skips I/O interface testing during its power-on self tests. This enables the system to
complete its boot process quicker. The default factory setting is for fastbootto be enabled
(set to on). Note that fastbootcan be set using the Boot Console Handler’s Configuration
Menu.
When fastbootis disabled (set to off), more extensive memory testing and I/O interface
testing is performed during the self tests, causing the boot process to take longer.
If you are experiencing difficulty in booting the system, set fastbootto off and reboot the
system. More extensive testing may reveal the error condition.
To display the status of fastboot, type the following at the prompt and press Enter:
Configuration Menu: Enter command> fastboot
To disable fastboot, type the following at the prompt and press Enter:
Configuration Menu: Enter command> fastboot off
To enable fastboot, type the following at the prompt and press Enter:
Configuration Menu: Enter command> fastboot on
160
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying the LAN Station Address
Disp la yin g th e LAN Sta tion Ad d r ess
It is sometimes necessary to supply the LAN station address of the workstation to other
users. For example, if the workstation is to become a member of a cluster, the cluster
administrator needs to know the LAN station address in order to add the workstation to
the cluster. Note that the LAN station address can be determined using the Boot Console
Handler’s Information Menu.
A LAN station address for the workstation is the label that uniquely identifies the LAN
connection for the workstation at the link level (the hardware level).
To display the workstation’s LAN station addresses, type the following at the prompt and
press Enter:
Information Menu: Enter command> lanaddress
The LAN station address is displayed as a twelve-digit number in hexadecimal notation,
similar to the following:
LAN Station Address:
001083-000429
The address is for the system’s built-in LAN.
Chapter 6
161
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Displaying System Information
Disp la yin g System In for m a tion
The allcommand allows you to display the system’s processor revision and speed, cache
size, memory size, flag settings, and the boot and console paths. To display system
information for the Information Menu, type the following at the prompt and press Enter:
Information Menu: Enter command> all
This information is paged to allow you to view it as necessary unless the service ScRoll
command has been used to disable scrolling.
Disp la yin g P IM In for m a tion
The pimcommand allows you to display the most recent PIM information for the specified
fault type. To display PIM information for a specific fault, from the Service Menu, type the
following at the prompt and press Enter:
Service Menu: Enter command >pim processor_numberfault_type
You can use pimin the following ways:
pim- No arguments for the pim command returns the HPMC information for processor 0
pim 0- HPMC information on processor 0
pim 0fault_type- fault type information on processor 0
where fault_type is HPMC (high priority machine check), LPMC (low priority machine
check), or TOC(transfer of control).
Sta b le Stor a ge
Stable storage is non-volatile memory associated with the PA-RISC processor module.
Stable storage is used by the processor (CPU) to store:
•
•
•
•
Device path information
The state of the boot flags
HPMC error information
Operating system initialization data
162
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
ISL Environment
ISL En vir on m en t
The ISL environment provides the means to load the operating system (HP-UX)
environment. The ISL environment also provides an offline platform to execute optional
diagnostic and utility programs from a boot device when HP-UX does not load.
The ISL program is the first program loaded into main memory from an external medium
(LAN, disk, or tape) and launched by the initial program loader (IPL) routine from the
Boot Administration environment.
The ISL environment provides the following capabilities:
•
Execute user-entered commands to modify boot device paths and boot options in stable
storage.
•
•
Run offline diagnostic programs and utilities
Provide automatic booting of the HP-UX operating system after power-on or reset
In vok in g ISL fr om th e Boot Con sole Ha n d ler
Perform the following steps to invoke ISL from the Boot Console Handler:
1. Follow the directions in “Accessing the Boot Console Handler” on page 142, and then
type the following at the prompt and press Enter:
Main Menu: Enter command > boot device
You are prompted:
Interact with ISL (Y, N, or Q) >y
2. Answering yes (y) causes the ISL to be loaded from the specified device. After a short
time, the following prompt appears on the screen:
ISL>
ISL is the program that actually controls the loading of the operating system. By
interacting with ISL, you can choose to load an alternate version of the HP-UX
operating system.
For example, if the usual kernel (/stand/vmunix) on the root disk (scsi.6.0) has
become corrupted, and you wish to boot the workstation from the backup kernel
(/stand/vmunix.prev), type the following at the ISL>prompt and press Enter:
ISL>hpux /stand/vmunix.prev
Chapter 6
163
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
ISL Environment
ISL User Com m a n d s
The following commands available in the ISL environment allow you to display and modify
the boot characteristics of the system.
• help- lists ISL command menu and available utilities.
• display- displays the boot and console paths in Stable Storage and the current setting
of the ISL Boot Flags.
• primpath- modifies the primary boot path entry in Stable Storage. The entry in Stable
Storage for the primary boot device begins at byte address 0 and ends at 31.
• altpath - modifies the alternate boot path entry in Stable Storage. The entry for the
alternate boot device begins at byte address 128 and ends at 159.
• conspath- modifies the console path entry in Stable Storage. The console device begins
at byte address 96 and ends at byte address 127. The entry for the keyboard and mouse
devices begins at byte address 160 and ends at 191.
• listautoflor lsautofl- lists the contents of the (HP-UX) autoboot file.
• support- boots the Support Tape from the boot device.
• readss - displays 4 bytes (one word) from Stable Storage. The readss command
requires a decimal number between 0 and 255 to address four bytes in Stable Storage.
164
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Obtaining and Updating System Firmware
Obta in in g a n d Up d a tin g System Fir m w a r e
To update a system’s firmware, obtain the firmware patch from the patch server website at
one of the following URLs:
http://us-external_support.hp.com
http://europe-external_support.hp.com
The patch file is a combined shar’ed file that contains an ASCII cataloging file, a readme
type ASCII file, and the firmware LIF binary file. The LIF volume is bootable to ODE,
which in turn runs the UPDATER utility to download the firmware image files.
To identify the current version of the firmware on the system to be updated, re-boot the
system and do the following:
1. Interrupt the boot process and, from the Boot Console Handler prompt, type
<information> and press Enter.
2. Identify the firmware revision. The last two digits in the patch name indicate the
revision.
To install the firmware update, follow the directions in the readmefile.
A new method to update the PA8500/8600 workstation system firmware is available
January 2000 as an OS patch. The initial patch is PHSS_19794on HP-UX 10.20 ACE 9912
and PHSS_20146on HP-UX 11.00 containing revision 3.1 system firmware. It will be
superceded with higher revision firmware patches as they are released. You can find the
patches by searching for firmware patchon the OS patch site.
Perform the installation by using swinstalland following the installation process. This
will cause a reboot to flash the firmware update and then another reboot to initialize the
system hardware with the new firmware revision. This process has the advantage of
starting the installation from the operating system, requires no special hardware such as a
DAT tape, and requires no user intervention other than waiting for the two reboots.
Chapter 6
165
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Console Handler
Obtaining and Updating System Firmware
166
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
A P r od u ct Sp ecifica tion s
This appendix lists the environmental and electrical specifications for the HP VISUALIZE
B2000 workstation.
167
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
Environmental Specifications
En vir on m en ta l Sp ecifica tion s
Altitu d e
Non-operating (storage or shipping): 0-15,000 ft above sea level (0-4500 m)
DC Ma gn etic Field In ter fer en ce
Operating: <1 Gauss at surface of product
Non-operating: <2 mGauss @ 7 feet
Electr om a gn etic Com p a tibility (EMC)
Emissions:
Immunity:
FCC Class B, CISPR B
EN61000-4-2: 1999 - 4KV contact discharge, 8KV air discharge (ESD)
EN61000-4-3: 1996 - 10V/m (radiated immunity)
EN61000-4-4: 1995 - 2kV signal lines, 4kV power lines (EFT)
Tem p er a tu r e
Operating: 5 to +35° C
Non-operating (shipping or storage): -40 to +70° C
Hu m id ity (Non -con d en sin g)
Operating: 15 to 80% RH
Non-operating: 0 to 90% RH (storage or shipping)
Lea k a ge Cu r r en t
Less than 3 milliamps
Sh ock
Operating: 20g at 3ms, 1/2 sine in normal axis with no hard errors
Non-operating (shipping): 80g at 3ms, 1/2 sine, normal axis
Vibr a t ion
Operating random: 0.21 Grms, 5-500 Hz
Swept sine survival (shipping): 0.5 G (0-peak), 5-500 Hz
Random survival (shipping): 2.09 Grms, 5-500 Hz
168
AppendixA
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
Electrical Specifications
Electr ica l Sp ecifica tion s
In p u t P ow er
7.4 Amps RMS max @ 100V
6.2 Amps RMS max @ 120V
3.8 Amps RMS max @ 200V
3.2 Amps RMS max @ 230V
Lin e Pow er
AC Frequency: 48-66 Hz
AC Voltage: 90-264V
Maximum Power Input: 805 Watts
Maximum Current Load: 10 Amps
Appendix A
169
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
Electrical Specifications
170
AppendixA
Download from Www.Somanuals.com. All Manuals Search And Download.
B Regu la tor y a n d Sa fety Sta tem en ts
This appendix lists the regulatory and safety statements for the HP VISUALIZE B2000
workstation.
171
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory and Safety Statements
Appendix Overview
Ap p en d ix Over view
This appendix contains the following main sections:
•
•
•
•
•
•
Declaration of Conformity
Emissions Regulations
Third-Party Emissions Regulations Compliance
Special Regulatory and Safety Information
Electrostatic Discharge (ESD) Precautions
Warnings
172
AppendixB
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory and Safety Statements
Declaration of Conformity
Decla r a tion of Con for m ity
according to ISO/IEC Guide 22 and EN 45014
Manufacturer:
Hewlett-Packard Company
3404 East Harmony Road
Fort Collins, CO 80528
USA
Declares, that the:
Product Name:
HP VISUALIZE Workstation
B1000 / B2000/ C3000
Model Numbers:
Base Product Number: A4985A / A5983A/ A4986A
Product Options:
all
conforms to the following specifications:
Safety
IEC 950:1991+A1+A2+A3 +A41/ EN 60950:1992+A1+A2+A3+A4+A11
IEC 60825-1:1993/EN60825-1:1994+A11 Class 1 for LED’s
USA 21CFR Subpart J - for FC Laser module
China GB4943-1995
Russia GOST R 50377-92
EMC
CISPR 11: 1997 / EN 55011: 1998 Class B
CISPR 22: 1993+A1+A2 / EN 55022: 1994 +A1+A2 Class B
EN 50082-1:1992
Also compliant with...
IEC 1000-3-2: 1994 / EN 61000-3-2: 1998
IEC 1000-4-2: 1995+A1 / EN 61000-4-2: 1999 - 4kV CD, 8 kV AD
IEC 1000-4-3: 1995 / EN 61000-4-3: 1996 - 10 V/m
IEC 1000-4-4: 1995 / EN 61000-4-4: 1995 - 2 kV Signal, 4 kV Power Lines
US FCC Part 15, Class B
Japan VCCI Class B
Australia/New Zealand AS/NZS 2046.1/2:1992, AS/NZS 3548:1995, and AS/NZS 4251.1:1994
China GB9254-1988
Taiwan CNS13438 Class A
Russia GOST R 29216-94
and is certified by:
UL Listed to UL1950, 2nd edition, File E146385
cUL Listed to CSA 22.2 No.950-M93
TUV Certified to EN60950 2nd edition with A1+A2+A3+A4+A11
HP Fort Collins CCQD HTC
supplementary information:
The product herewith complies with the requirements of the following Directives and carries the CE marking accordingly:
- the EMC directive 89/336/EEC and 92/31/EEC and 93/68/EEC
- the Low Voltage Directive 73/23/EEC and 93/68/EEC
This product was tested in a typical Hewlett Packard workstation configuration.
Original signed by Ruth Lutes, Site Quality Manager Fort Collins, CO, USA
For Compliance Information ONLY, contact:
European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE
Standards Europe, Herrenberger Straße 130, D-71034 Böblingen (FAX: +49-7031-14-3143)
Americas Contact: Hewlett-Packard, Fort Collins Site Quality Manager, mail stop 46, 3404 E. Harmony Rd., Ft. Collins, CO
80528, USA
Appendix B
173
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory and Safety Statements
Emissions Regulations
Em ission s Regu la tion s
The HP VISUALIZE B2000 workstation is FCC Class B compliant. Note that if a video out
cable is connected to your Video Out card, then your workstation is no longer FCC Class B
compliant as stated in the subsequent section “Special Video Configuration Statement.”
For F CC B Ap p lica tion s
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules and the Canadian Department of
Communications. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception (determined by turning the
equipment off and on), you should try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Ask the dealer or an experienced radio/television technician for help.
Hewlett-Packard's system certification tests were conducted with HP- supported
peripheral devices and HP-shielded cables, such as those you receive with your
workstation. Changes or modifications not expressly approved by Hewlett-Packard could
void the user's authority to operate the equipment.
Operation of this device is subject to the following conditions:
•
•
This device may not cause harmful interference.
This device must accept interference received, including interference that may cause
undesired operation.
•
Cables used with this device must be properly shielded to comply with the requirements
of the FCC.
174
AppendixB
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory and Safety Statements
Emissions Regulations
EMI Cla ss A R RL (Kor ea )
VCCI Cla ss B ITE (J a p a n )
EMI Cla ss A (Ta iw a n )
Sp ecia l Vid eo Con figu r a t ion St a t em en t
When a Video Out card has a cable connected to its video out connector, the HP VISUALIZE
B2000 workstation no longer meets FCC Class B regulations. The workstation now
becomes FCC Class A compliant. This statement applies only to those applications which
include a cable connected to the video out connector on a Video Out card. No modification
to the regulatory statements is necessary for applications which include cables connected
to other connectors on the card but not to the Video Out connector.
Appendix B
175
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory and Safety Statements
Third-Party Emissions Regulations Compliance
Th ir d -Pa r ty Em ission s Regu la tion s Com p lia n ce
Any third-party I/O device installed in HP system(s) must be in accordance with the
requirements set forth in the preceding Emissions Regulations statements. In the event
that a third-party noncompliant I/O device is installed, the customer assumes all
responsibility and liability arising therefrom.
Sp ecia l Regu la t or y a n d Sa fet y In for m a tion
This section covers regulatory and safety information for acoustics, lasers, and LEDs.
Acou st ics
Regu la t ion On Noise Decla r a t ion For Ma ch in es -3. GSGV
Lpa <70dB
Lpa <70dB
operator position
normal operation
per ISO 7779
am Arbeitsplatz
normaler Betrieb
nach DIN 45635 T.19
La ser Sa fety St a tem en t (U.S.A. On ly)
The CD-ROM mass-storage system is certified as a Class 1 laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968.
This means that the mass-storage system does not produce hazardous laser radiation.
Because laser light emitted inside the mass-storage system is completely confined within
protective housings and external covers, the laser beam cannot escape from the machine
during any phase of user operation.
LEDs
The LEDs on this product are classified as “Class 1 LED PRODUCT” in accordance with
EN 60825-1.
176
AppendixB
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory and Safety Statements
Electrostatic Discharge (ESD) Precautions
Electr osta tic Disch a r ge (ESD) P r eca u tion s
Electrostatic charges can damage the integrated circuits on printed circuits boards. To
prevent such damage from occurring, observe the following precautions during board
unpacking and installation:
•
•
Stand on a static-free mat.
Wear a static strap to ensure that any accumulated electrostatic charge is discharged
from your body to ground.
•
Connect all equipment together, including the static-free mat, static strap, routing
nodes, and peripheral units.
•
•
Keep uninstalled printed circuit boards in their protective antistatic bags.
Handle printed circuit boards by their edges once you have removed them from their
protective antistatic bags.
Appendix B
177
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory and Safety Statements
Warnings
Wa r n in gs
WARNING:
Removing the device cover may expose sharp edges in the equipment chassis. To avoid
injury, use care when installing customer add-on devices.
WARNUNG:
Das Entfernen der Geräteabdeckung legt die scharfen Kanten im Inneren des Gerätes frei.
Um Verietzungen zu vermeiden, seien Sie vorsichtig beim Einbau von zusätzlichen
Bauteilen, die vom Kenden selber eingebaut werden können.
AVERTISSEMENT:
Des bords tranchants du châssis de l´équipement peuvent étre exposés quand le cache de
l´unité n’est pas en place. Pour éviter des blessures, faire très attention lors de
l´installation de modules supplémentaires par le client.
WARNING:
Disconnect the power plug from the wall outlet or power source before moving or removing
a device, or installing add-on components.
WARNUNG:
Entfernen Sie die Stromzuführung von der Steckdose oder der Stromquelle bevor Sie das
Gerät bewegen, abbauen, oder zusätzliche Bauteile installieren.
ADVER TISSEMENT:
Débrancher la fiche de la prise de courant ou de la source d´alimentation électrique avant
de déplacer ou de retirer l´unité, ou avant d´installer des modules supplémentaires.
178
AppendixB
Download from Www.Somanuals.com. All Manuals Search And Download.
C Rela t ed Docu m en ta t ion
This appendix lists related documentation for the HP VISUALIZE B2000 workstation.
179
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Documentation
HP CE Tr a in in g CD-ROM
•
CE92-VIS_B2000 - HP VISUALIZE B2000 Workstation, CE Training
Ser vice Ma n u a ls
•
A5983-90039 - Service Handbook, HP VISUALIZE B2000 UNIX Workstation (this
handbook)
•
•
B2355-90040 - System Administration Tasks Manual HP 9000 Series 700
B3782-90176 - Support Media User’s Manual
User Ma n u a l
•
A5983-90001 - HP VISUALIZE B2000 Owner’s Guide
180
AppendixC
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossa r y
a tt a ch m en t u n it in ter fa ce
(AUI) A transceiver cable that
conforms to IEEE 802.3
specifications.
A
a b solu te p a t h n a m e The full
pathname of a file, including all
the directories leading to it,
starting with the root directory
(“/”) and ending with the filename
itself See also file, filename,
pathname.
B
ba ck u p v. To make a copy of one
or more files on a tape or disk that
can be stored separately from the
a ccess p er m ission s Settings that original files.
allow (or prevents) a user or group
of users to read, write, or execute
files See also file access
permissions.
ba ck u p n. A spare copy of one or
more files on a tape or disk that
can be used to restore data into its
original location.
a ctive w in d ow The window that
is receiving input from the
keyboard at the present time. If
there is no active window,
anything you type is lost. Only one
window can be the active window.
b itm a p Generally speaking, an
array of data bits that define a
graphical image. Strictly speaking,
a bitmap is a pixmap whose depth
is one bit, capable of representing
two-color (black-and-white)
images.
ANSI The American National
Standards Institute, a non-profit
organization, made up of various
expert committees, that publishes
standards for use by national
industries. ANSI has adopted the
IEEE standards for local area
networks.
b oot Short for “bootstrap,” from
the phrase “pulling oneself up by
one’s bootstraps.” Indicates the
beginning of a process from the
lowest possible level. A boot service
is provided by a short program,
stored in the boot ROM (read-only
memory) of your workstation, that
loads the operating system (or any
complex program) into main
a r gu m en t A part of a command
line or line of source code that
identifies the file, directory, or
other data to be used; a parameter. memory. Partner workstations
provide bootstrap service to
181
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
diskless workstations. See also
boot ROM.
read from and written to these
disks. CD-RAM disks are 120 mm
(4.7 inches) in diameter, use one
data surface, and have a capacity
of about 650 MB. The data surface
contains pits and flat spots
arranged in a continuous spiral
track, which is read at a constant
linear speed.
Boot Con sole H a n d ler The
interactive firmware that enables
you to interact with the hardware
of your workstation before the
workstation boots the operating
system. The Boot Console Handler
allows you to perform special
tasks, display information, and set
certain system parameters.
CD-R AM d r ive A random-access,
read/write, mass-storage device
that uses removable CD-RAM
disks. The drive contains a
semiconductor laser for reading
and writing data optically and an
embedded controller.
b oot R OM A read-only memory
that is incorporated into a
workstation for the purpose of
loading and starting the operating
system, and modifying the
configuration or changing the
booting behavior.
CD-R OM Compact Disk
Read-Only Memory. See also
CD-ROM disk, CD-ROM drive.
b ootstr a p ser vice See boot.
CD-R OM d isk CD-ROM disks are
identical to the audio compact
disks (CDs) used to record stereo
music, except that they store
computer data. CD-ROM disks are
120 mm (4.7 inches) in diameter,
use one data surface, and have a
capacity of about 650 MB. The data
surface contains pits and flat spots
arranged in a continuous spiral
track, which is read at a constant
linear speed.
b yte A fundamental
character-code unit, usually
consisting of 8 bits.
C
CD-R AM Compact Disk
Random-Access Memory. See
also CD-RAM disk, CD-RAM drive.
CD-R AM d isk CD-RAM disks are
identical to the audio compact
disks (CDs) used to record stereo
music, except computer data is
182
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
CD-R OM d r ive A random-access,
read-only, mass-storage device that
uses removable CD-ROM disks.
The drive contains a
semiconductor laser for reading
data optically and an embedded
controller.
clu st er n od e A member of a
group of workstations connected
via a Local Area Network (LAN).
One workstation, the cluster
server, acts as a file server to the
other machines in the cluster.
See also cluster, cluster client,
cluster server.
Cen t r a l P r ocessin g Un it (CP U)
clu st er ser ver A workstation that
provides file access, login access,
file transfer, printing, and other
services across a network to a
defined cluster of systems (cluster
nodes) connected via a LAN. See
also cluster, cluster client, cluster
node, host.
The part of a workstation that
interprets and executes
instructions; the “brain.”
ch ild d ir ect or y See
subdirectory.
click To press and immediately
release a mouse button. The term
comes from the fact that pressing
and releasing most mouse buttons
makes a clicking sound. Compare
drag and drop.
cold in st a ll A process that
requires the booting of an install
kernel from an install server over a
network or from a CD-ROM and
answering some configuration
questions.
clu st er A group of workstations
connected via a Local Area
Network (LAN). One workstation,
the cluster server, acts as a
file-system server for the cluster
clients. See also cluster client,
cluster node, cluster server.
com m a n d An instruction that you
enter into the system at a prompt,
to execute a program or perform a
task. See also shell command.
com m a n d a r gu m en t
clu st er clien t A cluster node that
does not have a local HP-UX file
system. Its file system resides on
the cluster server. See also
Information you provide on a
command line to describe the
object (often a file or directory) to
be operated on by the command.
cluster, cluster node, cluster server.
183
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
com m a n d in ter p r eter A
commands. To enter a control key
sequence, hold down the “Ctrl” key
while pressing another key.
program that reads lines of text
from standard input (typed at the
keyboard or read from a file) and
interprets them as requests to
execute commands or programs.
An HP-UX command interpreter is
called a shell. See also shell.
cp u See Central Processing
Unit.
cu r r en t d ir ector y See current
working directory.
com m a n d op t ion Information
you provide on a command line to
indicate any special action you
want the command to take, or
mode in which to operate. See
also default.
cu r r en t session The work and
processes that have been created
since you logged into the system
(and before you log out again).
See also session.
con figu r a t ion The arrangement
of a workstation or network as
defined by the nature, number, and
chief characteristics of its
functional units. More specifically,
the term “configuration” may refer
to a hardware configuration or a
software configuration.
cu r r en t w or k in g d ir ect or y The
directory from which a
relative-pathname search begins,
as well as the directory in which
you are currently working. It is
also called the “working directory”
or “current directory.”
cu r sor The small, usually
blinking, box or underline
displayed in whatever screen or
window is active at any particular
time. The cursor marks your
current typing position on the
screen and indicates which
program (HP CDE terminal
window or shell) will receive your
typed commands.
con sole The tty (terminal) the
system was booted from. The
console is associated with the
monitor where all system
messages are displayed. The
system administrator sends
messages to other system users
from this tty.
con t r ol k ey sequ en ce A
keystroke combination used as a
shorthand way of specifying
184
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
on each side of the board are
connected to different chips. This
allows for a wider data path as
more modules can be accessed at
the same time.
D
d a isy-ch a in in g A method of
connecting devices in which the
signal passes from one device to
the next in serial fashion along a
bus.
d ir ector y A special type of
“container” object that contains
information about the objects
beneath it in the HP-UX
organizational structure. Basically,
it is a file that stores names and
links to files and other
DDS t a p e d r ive A device that
stores data on Digital Data
Storage (DDS) cassettes.
d efa u lt Most commands give you
a choice of one or more options. If
you don’t specify an option, the
command automatically assigns
one. This automatic option is called
the “default.” See also command
option.
directories See also file.
d isk A thin, round plate with a
magnetic or optical surface coating
on which data is stored by
magnetic or optical means. See
also floppy diskette, hard disk,
CD-ROM disk.
d ia log b ox A special type of HP
CDE screen that contains controls
and settings, and with which the
user can carry on an interactive
“dialog” in the process of setting
whatever parameters the dialog
box requests. To display an
d isk ed w or k st a t ion A
workstation that has its own hard
disk drive.
d isk et te See floppy diskette.
example of a dialog box, click the
Style Manager button on the
Workspace Manager’s front panel,
then click on Color.
d ou b le-click To press and release
a mouse button twice in rapid
succession. The amount of time
that discriminates between a
double click and two single clicks is
usually user-configurable. Double
clicking usually invokes a
DIMM See Dual In-line Memory
Module.
different, but related, function
than single clicking.
Du a l In -lin e Mem or y Mod u le A
memory board whose connectors
185
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
d r a g To move the mouse (and
hence the pointer on the screen)
while holding down one or more of
its buttons. This process specifies
two separate locations on the
screen for those operations that
require two: the location when the
mouse button is pressed, and the
location when it is released. This is
used, for example, to initiate a
file-copy by pressing the mouse
button on the file to be copied,
dragging the file’s icon to the
destination window, and releasing
the mouse button there. Another
common using of dragging is to
specify the upper-left and
E
EEP ROM Electronically erasable
read-only memory. Usually bytes
or words can be erased and
reprogrammed individually during
system operations. The EEPROM
is used for storing configuration
information that will be
“remembered” after a reboot and
AC power loss.
en vir on m en t The conditions in
which your commands or programs
are executed. These conditions
include your workstation
characteristics, home directory,
and default search paths See also
environment variables.
lower-right corners of a new
window or similar rectangle See
also drop.
en vir on m en t va r ia b les The set
of defined shell variables (some of
which are PATH, TERM, SHELL,
EXINIT, and HOME) that define
the conditions in which, or values
with which, your commands are
executed. These conditions and
values include your workstation
characteristics, home directory,
and default search paths See also
environment.
d r ive See CD-ROM drive, DDS
tape drive, floppy drive, hard disk
drive
d r op To release the mouse button
after having moved the mouse with
its button held down, in order to
position an icon or other object
that has been “dragged” to a new
position See also drag.
Et h er n et The LAN developed
jointly by Digital Equipment
Corporation, Intel, and Xerox
Corporation, upon which the IEEE
802.3 network is based.
186
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
fir m w a r e The control software
that is embedded in ROM and is
always resident regardless of the
status of the operating system. It
handles the booting of the system,
initialization of I/O, and starts the
loading of the operating system.
F
file The basic named unit of data
stored on disk See also directory,
filename.
file a ccess p er m ission s The
access rights given to a particular
file or directory. Every file and
directory has a set of access
permissions, a code that
determines whether a process can
perform a requested operation on
the file (such as opening the file or
writing to it) See also access
permissions.
flop p y d isk ett e A thin, flexible,
disk-shaped sheet of plastic that
magnetically stores data on its
coated surfaces. Floppies are
contained within stiff plastic
“envelopes” to protect them from
dust, fingerprints, and abrasion.
The floppy drive uses heads
(similar to heads in tape recorders)
to read and write data on
File Ma n a ger The HP CDE
application that allows you to
manage your files and directories,
and to set viewing preferences.
concentric disk tracks.
flop p y d r ive A device that stores
data on a floppy diskette.
filen a m e The name given to a
particular file See also absolute
pathname, file, pathname.
H
h a r d d isk A type of disk that is
rigid—often aluminum—as
opposed to a thin plastic diskette,
which is flexible.
file ser ver A workstation whose
primary task is to control the
storage and retrieval of data from
hard disks. Any number of other
workstations can be linked to the
file server via a LAN in order to
use the file server to access data.
h a r d d isk d r ive A device that
stores data on a hard disk. The
hard disk can be a permanent part
of the drive and thus be
file syst em The hierarchically
organized set of files and
directories on a hard disk.
unremovable, or it can be
removable. If it is removable, it is
contained in a protective cover that
187
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
is opened by the drive when access
is needed.
operating system, and X Window
system), enabling you to control
your workstation by directly
manipulating graphical objects
instead of by typing commands at
a command-line prompt.
Help Ma n a ger The HP CDE
application that provides online
help.
$HOME The environment
variable that contains the name of
a user’s home directory. This is the
directory in which you are placed
upon logging in. Typically, this is
/home/login, where login is your
username. See also home
directory.
HP -UX This is Hewlett-Packard’s
version of the UNIX® operating
system.
HP -UX clu st er See cluster
node, cluster server.
I
h om e d ir ect or y A shorthand way
of referring to a frequently used
directory, almost always the login
directory.
icon A small, graphic
representation of an object. Objects
can be “iconized” (turned into
icons) to clear a cluttered
workspace. Icons can be restored to
their original appearance when
needed. Whatever processes are
executing in an object continue to
execute when the object is
iconized.
h ost A computer that offers one or
more services; may be local or
remote (accessible via a
network) See also cluster server.
h ost n a m e See internet protocol
address.
icon ify See iconize.
HP CDE See HP Common
Desktop Environment.
icon ize To turn a window or shell
into an icon See also icon.
HP Com m on Desk top
In itia l Syst em Loa d er The
E n vir on m en t A user interface
that draws a graphical layer over
the complexities of the other layers
of the system (the hardware,
program that actually controls the
loading of the operating system.
188
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
in p u t d evice Any of several
which the first character is a
pieces of hardware equipment used period (.). Invisible filenames are
to give information to a system.
Examples include the keyboard
and the mouse See also output
device.
not displayed by the listing
commands such as ls and ll
without additional options, such as
-a.
in p u t w in d ow The window that
displays a program’s prompt and
any commands typed but not yet
executed.
IP a d d r ess See internet protocol
address.
ISL See Initial System Loader.
In st a n t Ign it ion When the user’s
computer is turned on and it
automatically boots up and is
ready for use. Instant Ignition is
the result of the computer’s
operating system being preloaded
at the factory.
K-L
k er n el The part of the operating
system that is an executable piece
of code responsible for managing
the computer’s resources. The
kernel controls the rest of the
operating system.
in st a ll ser ver This is a networked
computer from which file sets and
operating systems can be installed.
LAN See local area network.
LAN st a tion a d d r ess See local
area network station address.
in ter n et p r ot ocol a d d r ess (IP
a d d r ess) A string of characters, in
the format nnn.nnn.nnn.nnn, that
uniquely identifies a workstation
in a network. The nnn in the
lin k n. A special object that
contains the name of another
object. When you specify a link as a
pathname or part of a pathname,
the system substitutes the
format specifier above is a one- to
three-digit decimal integer
between 0 and 255, inclusive, in
which leading zeroes are optional.
The internet protocol address is
also referred to as the “IP address.”
pathname that the link contains.
lin k v. To establish a relationship
between two objects such that one
of the objects contains only the
information required to associate it
in visib le filen a m e A filename in
189
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
with the other, “real,” object.
Login Ma n a ger The program
that controls the initial startup of
HP CDE and accepts the user’s
username and password
loca l a r ea n etw or k (LAN) A
data communications system that
allows a number of independent
devices to communicate with each
other. The systems and clusters
that share data, hardware, and
software resources via Networking
Services software.
login scr ip t The shell program
that runs at each login, and sets
the login environment for your
system.
M
loca l a r ea n etw or k syst em
a d d r ess The label that uniquely
identifies the local area network
(LAN) connection for your
m en u ba r An area at the top or
bottom of a window that contain
the titles of the pull-down or
workstation at the hardware level.
This 48-bit number is preassigned
by HP on their computers and it
must never be changed.
pop-up menus for that application.
m in im ize b u t ton In HP CDE, a
push-button on the window frame
that turns a screen into an icon.
See also icon, iconize.
log in v. To initially sign on to the
system so that you may begin to
use it. This creates your first user
process. See also username.
m on itor t yp e A monitor path
name (graphics(1) through
graphics(6)) that is associated with
a particular resolution and refresh
frequency at which you want your
monitor to operate. The monitor
type is selected using the Boot
Console Interface. See Chapter 6.
login n. A session. Or, a string of
characters that uniquely identifies
a user of the system See also
session, user account, and
username.
login d ir ect or y The directory in
which you are placed when you log
in, usually your home directory
m ou se p oin ter See pointer.
See also home directory.
190
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
n od e n a m e A unique identifying
name given to a workstation in a
cluster See also cluster, node.
N
n a m e A character string
associated with a file, directory, or
link. A name can include various
alphanumeric characters, but
never a slash (/) or null character
n on vola tile m em or y System
memory that retains its contents
even after workstation power is
turned off.
See also pathname.
O
n etw or k Two or more
workstations sharing
information See also cluster,
workstation.
ob ject Any file, directory, or link
in the network. See also directory,
file, link, pathname.
n etw or k con t r oller A printed
circuit board that passes bit
streams between the network and
the main memory of the
workstation. Coupled with the
network transceiver, the controller
also handles signal processing,
encoding, and network media
access.
op er a t in g system The program
that supervises the execution of
other programs on your
workstation. For example, the
entire HP-UX system, including
the kernel and all HP-UX
commands See also kernel.
op t ion See command option.
ou tp u t d evice Any of several
pieces of hardware used for
receiving messages from the
computer and storing them, or
making them perceptible by
humans. Disks and tapes,
computer monitors, printers,
plotters are examples of output
devices See also input device.
n od e A computer that is on a
network. Each node in the network
can use the data, programs, and
devices of other network nodes,
assuming permissions are set up
properly. Each node contains main
memory and has its own disk or
shares one with another node
See also disked workstation,
diskless workstation, workstation.
191
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
ou tp u t w in d ow The window that
displays a process response to your
command.
ends with the name of the
destination object See also name,
object.
p er m ission s A set of rights (read,
write, execute) associated with an
object in the file system.
Determines who may use the
object and how.
P
p a r en t d ir ect or y A directory
that contains other directories,
each of which is then called a
subdirectory See also
P ID Process Identifier. Also
referred to as a process ID See
also process ID.
subdirectory.
p a ssw or d The secret word you
enter next to the password prompt
at login time to permit only
authorized access. Keep your
password secret and change it
occasionally in order to protect
your account from unauthorized
use See also user account.
P IM Processor Internal Memory.
The pim command is a command
used by the Boot Console Interface
for determining specific system
faults. See also processor internal
memory.
p oin t er Sometimes called the
“mouse pointer,” the pointer’s
location on the display corresponds
to the mouse’s location. The
p a t h The hardware address of a
device that is attached to the I/O
system of your workstation.
pointer’s shape often depends on
the object its hot-spot covers (this
is used as a visual feedback
mechanism from a program to the
user). In the HP CDE Workspace,
the default pointer is an X; on a
window frame, it is either a simple
arrow, or an arrow with one or
more straight lines touching it (to
indicate any of the eight
p a t h n a m e A slash/separated
series of zero or more directory
names followed by a filename, that
together describe the path within
the file system from some starting
point to a destination object.
Pathnames (other than the
degenerate empty case) begin with
the name of the starting point, and
include every directory name
between the starting point and the
destination object. A pathname
window-resizing regions).
192
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
p r ocess A computing
action or set a state.
R-S
environment in which you may
execute programs; a program
currently running in the system.
R AM Random-access memory.
R OM Read-only memory.
r oot See superuser.
p r ocess ID A unique
identification number assigned to
all processes by the operating
system. Also referred to as a PID
See also PID.
scr oll b a r A vertical or horizontal
bar located on the side or bottom of
a window that allows the user to
view information that does not fit
within the window.
p r ocessor in ter n a l m em or y A
storage area in a processor (for
example, EEPROM) that is set at
the time of a high-priority machine
check (HPMC), low-priority
machine check, soft boot or TOC,
and is composed of the architected
state save error parameters, and
hardware version-dependent
regions.
SCSI See Small Computer
System Interface.
SCSI ID The address of a
peripheral device connected to a
SCSI bus.
p r ogr a m A unit of executable
code, in source-code or binary form.
Most HP-UX commands and
routines consist of programs.
ser ver A program that controls all
access to input and output devices.
session The time between when
you log in and when you log out.
Also called a “work session” or a
“login session.” See also current
session.
p r om p t A message or symbol
displayed by the system to let you
know that it is ready for your
input.
sh ell A command-line interpreter
program used to invoke programs.
Some examples of HP-UX shells
are the Bourne, Korn, Key, and C
shells. Sometimes referred to as a
p u sh b u t ton A graphic control
that simulates a real-life push
button. Use the pointer and mouse
to push the button and start an
193
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
“command interpreter.” See also
SPA Soft Physical Address. See
command interpreter.
also soft physical address.
sh ell com m a n d An instruction
you give the system to execute a
utility program or shell script
soft p h ysica l a d d r ess This is a
location in system memory
associated with the DIMM cards.
See also shell script, utility
program.
sta n d a lon e A workstation that is
not part of a cluster See also
cluster.
sh ell scr ip t A file that contains
commands that the system can
interpret and run in a shell.
St yle Ma n a ger The HP CDE
application that provides the
ability to customize various
user-interface aspects of your
system, including colors, fonts,
keyboard and mouse attributes,
session start-up and termination
behavior, and access to other
workstations.
sh u td ow n The process of taking
the system from multi-user state
to system administration state.
slid er One of the components of a
scroll bar. The slider is the object
that is dragged along the scroll
area to cause the window’s
contents to move, exposing
previously hidden content.
su b d ir ect or y A directory that is
located in, or anywhere on a path
below, another directory. The
directory above the subdirectory is
called the “parent directory.” A
subdirectory is also referred to as a
“child directory See also parent
directory.
Sm a ll Com p u ter System
In ter fa ce (SCSI) An IEEE
standard for interfacing a
computer to multiple, disparate
high-speed peripherals such as a
disk drive, a CD-ROM drive, or a
scanner, etc., singly or in
combination See also Ultra2
Wide Low-Voltage Differential
SCSI.
su p er u ser A user with permission
to enter any directory and make
changes to files and programs that
typical users are not allowed to
change. To “become superuser” or
“become root” means to let the
system know that you are now
194
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
assuming the role of system
administrator. You can do this
either by logging into the system
as user root, or by typing su
(switch user) at a command-line
prompt. You must know the root
password to become root.
tit le b a r The rectangular area,
between the top of the window and
the window frame, that contains
the title of the window object.
TOC See transfer of control.
tr a n sceiver A device that
system a d m in ist r a tor The
person responsible for system and
network installation, updating,
maintenance, and security at your
site.
transmits and receives signals.
tr a n sfer of con tr ol Saves the
state of the processor in Processor
Internal Memory (PIM) and
pending I/O operations are not
system ca ll Invocation of a kernel disturbed.
process by a user program.
Ultr a 2 Wid e Low -Volt a ge
system n a m e See internet
protocol address.
Differ en tia l SCSI A 16-bit-wide
bus with low-power receivers and
drivers, which allows a cable
length of up to 12 meters and a
data transfer rate of up to 80 MB
per second See also Small
T-U
ter m in a l w in d ow A terminal
window is a type of HP CDE
window that emulates a complete
display terminal. Terminal
windows are typically used to fool
window-dumb programs into
believing they are running in their
favorite terminal. When not
running programs or executing
operating system commands,
terminal windows display the
command-line prompt See also
HP Common Desktop
Computer System Interface.
u ser a ccou n t The system
administrator defines a user
account for every person
authorized to use the system. Each
user account contains the name
the computer uses to identify the
person (user ID), and the person’s
password. User accounts also
contain project and organization
names, to help the system
determine who can use the system
and what resources each person or
Environment.
195
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
organization is authorized to
use. See also user ID, password.
computing environment in which
you may execute programs, edit
text, display graphical images,
etc. See also Workspace Manager.
u ser ID The name the computer
uses to identify you. Your system
administrator assigns you a user
ID. Enter your user ID during the
login procedure when the system
displays the login prompt See
also user account.
Win d ow Ma n a ger The HP CDE
program that controls the size,
placement, and operation of
windows.
w or k in g d ir ector y See current
u ser n a m e The name that the
system recognizes as uniquely
yours. Also known as your “login
name.” The username is also the
name that identifies you to the
mail system and other software
requiring secure entry.
working directory.
Wor k sp a ce What the screen
becomes when you start HP CDE.
Although you can hide the
workspace under terminal
windows or other graphic objects,
you can never position anything
behind the workspace. All windows
and graphic objects appear stacked
“on top of” the workspace See
also HP Common Desktop
u tilit y See utility program.
u tilit y p r ogr a m A program
provided with the operating
system to perform a frequently
required task, such as printing a
file or displaying the contents of a
directory See also command,
shell command.
Environment, terminal window.
Wor k sp a ce Ma n a ger The
program that controls the size,
placement, and operation of
windows on the HP CDE
Workspace. The Workspace
Manager is a special Window
Manager See also Window
Manager.
W
w in d ow A rectangular area of the
screen for viewing information. HP
CDE allows you to create several
types of windows on the screen.
Each window is a separate
196
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
w or k st a tion A compact,
graphics-oriented computer having
high speed and high memory
capacity. A workstation usually
includes a keyboard, a monitor,
and a system unit. See also node,
disked workstation, diskless
workstation.
197
Download from Www.Somanuals.com. All Manuals Search And Download.
198
Download from Www.Somanuals.com. All Manuals Search And Download.
In d ex
A
keyboard, USB, 28
LAN connector, 24
Acoustics regulations, 176
all command, 162
laser safety statement, 176
LCD, 18
Applications, FCC B, 174
Audio connectors, 25
LEDs, 176
memory failures, 30
memory, description of, 30
monitor connector, 23
monitors supported, 27
mouse, USB, 28
Audio ports, 17
auto boot and auto search commands, 158
Auto boot and auto search, setting, 158
B
non-exchange FRUs, 84
operating system overview, 29
parallel connector, 24
power cord connector, 27
power switch, 19
B2000
acoustics regulations, 176
audio connectors, 25
block diagram, 133
CD drive, 19
product description, 16
rear panel components, 22
reference documentation, 179
regulatory statements, 171
safety statements, 171
security loop, 26
chassis codes, troubleshooting, 54
components diagram, 83
configuration, 31
connectors on rear panel, 22
Declaration of Conformity, 173
documentation, reference, 179
electrical specifications, 169
emissions regulations, 174
emissions regulations compliance,
third-party, 176
serial connectors, 23
specifications, 167
storage devices, 19
TOC button, 25
troubleshooting, 41
environmental specifications, 168
ESD precautions, 177
exchange FRUs, 84
updating firmware, 165
USB connectors, 24
USB hub, 24
exploded view diagram, 83
firmware, updating, 165
floppy disk drive, 21
video configuration statement, 175
warnings, 178
Battery, removal and replacement of, 113
Block diagram, 133
flowcharts for troubleshooting, 42
front panel components, 18
FRUs, 81
boot command, 144
Boot command notations, 52
Boot Console Handler
accessing, 142
graphics, optional, 17
HP-UX overview, 29
I/O slots, 23
all command, 162
key features, 16
auto boot and auto search commands, 158
Index
199
Download from Www.Somanuals.com. All Manuals Search And Download.
In d ex
boot command, 144
Chassis codes
bootable media, 146
Configuration menu, 139
fastboot mode, 160
explanation of, 47
table of, 54
Components
features, 137
exploded view diagram, 83
firmware, updating, 165
I/O slots, status of, 157
Information menu, 140
io command, 157
front panel, 18
rear panel, 22
Computer
booting, 144
ipl device types, 146
resetting, 147
ISL environment, 163
LAN station address, 161
lanaddress command, 161
Main menu, 138
Configuration
CD drive, 37
displaying monitor type, 151
floppy disk drive, 37
hard disk drive, 32
hard disk drive as a file system, 33
hardware, 32
memory configuration, 156
monitor command, 150
monitor configuration, 151
paths, 148
I/O cards, 39
memory, 38
memory, displaying current, 156
monitor type selection, 40
system hardware, 32
workstation, 32
Connectors
PIM information, 162
resetting the workstation, 147
search command, 146
secure command, 159
security mode, 159
Service menu, 141
system information, 162
Boot failure, troubleshooting, 50
Boot path, mnemonic style notation, 148
Bootable device troubleshooting flowchart,
45
audio, 25
LAN, 24
locations of, 22
monitor, 23
parallel, 24
Bootable media, searching for, 51, 146
Booting the workstation, 144
Button, TOC, 25
power cord, 27
rear panel, 22
serial, 23
USB, 24
Console troubleshooting flowchart, 44
C
CD drive
D
configuration, 37
features, 19
Declaration of Conformity, 173
Device types, ipl, 146
removal and replacement, 91
200
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
In d ex
Diagnostics
HP-UX, 46
Mesa (Support Tools Manager), 78
ODE, 79
Diagrams
main (power on LCD), 43
Front panel
components, 18
removal and replacement of, 87
FRU
block, 133
exploded view, 83
DIMMs
configuration, 38
description of, 30
memory failures, 30
removal and replacement, 114
Documentation, reference, 179
battery, 113
CD drive, 91
DIMM cards, 114
exchange part numbers, 84
fans, 124
floppy disk drive, 96
front panel, 87
hard disk drive, 104
I/O cards, 110
E
Electrical specifications, 169
Electrostatic discharge (ESD) precautions,
177
I/O fan, 124
LCD, 90
left side panel, 88
memory DIMMs, 114
non-exchange part numbers, 84
power supply, 119
power switch, 90
EMI gasket, 88
Emissions regulations, 174, 176
Environmental specifications, 168
ESD precautions, 177
Exchange FRUs, list of, 84
Exploded view diagram, 83
real time clock module, 113
removable media devices, 91
removal and replacement, 86
speaker, 127
system board tray assembly, 129
system fan, 126
F
Fans
removal and replacement of, 124
troubleshooting, 48
Fastboot mode, displaying and setting, 160
FCC B applications, regulations for, 174
Firmware, updating, 165
Floppy disk drive
G
Graphics path parameters, 150
Graphics, optional, 17
configuration, 37
H
features, 21
removal and replacement, 96
Flowcharts for troubleshooting
bootable device, 45
Hard disk drives
configuration, 32
configuring as a file system, 33
features, 19
console, 44
Index
201
Download from Www.Somanuals.com. All Manuals Search And Download.
In d ex
removal and replacement, 104
Hardware configuration, 32
HP-UX
operating system overview, 16, 29
troubleshooting flowchart, 46
K
Keyboard, USB, 28
Korea RRL, 175
L
LAN connector, 24
I
LAN station address, displaying, 161
lanaddress command, 161
Laser safety statement, 176
LCD, 18
I/O
slots, 17, 23, 39
standard, 17
I/O cards
chassis codes for troubleshooting, 47, 54
power on troubleshooting flowchart, 43
removal and replacement, 90
LEDs, regulations, 176
Left side panel, removal and replacement of,
88
configuration, 39
removal and replacement, 110
I/O fan
removal and replacement, 124
troubleshooting, 48
I/O slots
Line power specifications, 169
displaying status of, 157
installing I/O cards, 110
Information, displaying system, 162
Input power specifications, 169
Interface, user, 16
Internal storage devices, 16
CD drive, 19
floppy disk drive, 21
hard disk drives, 19
io command, 157
ipl device types, 146
ISL
M
Main troubleshooting flowchart, 43
Memory
Boot Console Handler information sample,
156
configuration, 38
description of, 30
DIMMS, removal and replacement of, 114
displaying current configuration, 156
failures, 30
main, 16, 30
environment, 52
user commands, 164
website, 42
Mesa (Support Tools Manager), 78
monitor command, 150
Monitor connector, 23
Monitors
J
configuration, 40
Japan, VCCI Class B ITE, 175
displaying configuration, 151
setting the type, 151
setting the type at power on, 154
setting the type using SAM, 152
202
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
In d ex
supported, 17
Processor fan
supported, list of, 27
troubleshooting, 155
type selection, 40
Mouse, USB, 28
removal and replacement, 124
troubleshooting, 48
Product description, 16
Product specifications, 167
N
R
Networking
Real time clock module, removal and
replacement of, 113
Rear panel
LAN connector, 24
standard supported, 16
Non-exchange FRUs, list of, 84
components, 22
I/O slots, 23
security loop, 26
O
TOC button, 25
ODE diagnostics, 79
Rear panel connectors
audio, 25
Offline Diagnostic Environment (ODE), 79
Operating system, HP-UX
overview, 16, 29
LAN, 24
list of, 22
troubleshooting flowchart, 46
locations of, 22
monitor, 23
P
parallel, 24
Panel
front, 87
left side, 88
power cord, 27
serial, 23
USB, 24
Parallel (IEEE 1284) port, 17
Parallel connector, 24
path command, 148
Reference documentation, 179
Regulations, emissions, 174
Regulatory and safety information, special,
176
Paths, displaying or setting, 148
PCI slots, 17
Regulatory statements, 171
Removal and replacement, FRU, 86
reset command, 147
Resetting the workstation, 147
RRL, Korea, 175
PIM information, displaying, 162
Power cord connector, 27
Power on LCD troubleshooting flowchart, 43
Power specifications, 169
Power supply, removal and replacement of,
119
Power switch
description of, 19
removal and replacement, 90
Index
203
Download from Www.Somanuals.com. All Manuals Search And Download.
In d ex
S
flowcharts, 42
Safety and regulatory information, special,
HP-UX flowchart, 46
176
ISL environment, using, 52
LCD-indicated conditions, 47, 54
main flowchart, 43
Safety statements, 171
search command, 146
secure command, 159
Mesa (Support Tools Manager), 78
monitors, 155
Security loop, 26
Security mode, displaying and setting, 159
Selftest failures, troubleshooting, 53
Serial (RS-232) port, 17
Serial connectors, 23
ODE diagnostics, 79
power on LCD flowchart, 43
selftest failures, 53
system verification tests, 78
shutdown -q, 19
Side panel, removal and replacement of, 88
Speaker, removal and replacement of, 127
Specifications
U
Universal Serial Bus (USB) port, 17
Updating firmware, 165
USB
electrical, 169
environmental, 168
connectors, 24
Storage devices
hub, 24
CD drive, 19
keyboard, 28
floppy disk drive, 21
mouse, 28
hard disk drives, 19
User interface, 16
System board, removal and replacement of,
129
V
System fan
VCCI Class B ITE (Japan), 175
Video configuration statement, 175
removal and replacement, 126
troubleshooting, 48
System hardware configuration, 32
System information, displaying, 162
System verification tests, 78
T
TOC button, 25
Troubleshooting
boot command notations, 52
boot failure, 50
bootable device flowchart, 45
bootable media, searching for, 51
console flowchart, 44
fans, 48
204
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Baby Accessories PD261471A User Manual
Hamilton Beach Blender 70610C User Manual
Havis Shields Window WGI F7 H User Manual
Heat Glo LifeStyle Cooktop TiaraE 4035 822 User Manual
Heath Zenith Door 598 1109 05 User Manual
Hotpoint Oven SY11 User Manual
HTC Cell Phone SM TP008 1125 User Manual
Husqvarna Chainsaw 136 141 136LE 141LE User Manual
Husqvarna Chainsaw 2083 II User Manual
Husqvarna Trimmer 325RJX Series User Manual