QuickSpecs
Overview
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
1. Power LED/Beep LED
3. 15” TFT 5-Wire Resistive Touch Screen – standard on all
models
2. Multi-Track (3) Magnetic Stripe Reader (MSR) - Available on
select models
1. Two 2.5” Storage Drive bays
5. Advertisement panel (non-electrical)
2. One USB 2.0 port, one audio line-out and one microphone- 6. Main display hinge, allows for 90-degree pitch adjustment
in jack
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Standard Features
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Processors
Intel® Celeron® 440 (2.0 GHz, 512K L2 Cache, 800 MHz FSB)
Intel Core™ 2 Duo E7400 (2.8 GHz, 3 MB L2 Cache, 1066 MHz FSB)
Operating System
Preinstalled
Genuine Windows 7 Professional 32-bit*
Genuine Windows 7 Professional 64-bit*
FreeDOS
†
Windows Embedded POS Ready 2009
*This system may require upgraded and/or separately purchased hardware and/or a DVD drive to install
the Windows 7 software and take full advantage of Windows 7 functionality. See
http://www.microsoft.com/windows/windows-7/ for details.
†
Factory preinstall not available. Drivers support only.
Graphics
Display
Integrated Intel Graphics Media Accelerator 3000
15-inch diagonal TFT dual-bulb display, 1024 x 768 resolution, with 5-wire resistive type touchscreen.
Precalibrated at factory but should be recalibrated after initial software via the calibration wizard. Hard
or soft stylus input: finger tip, finger nail, or credit card edge to perform touch.
Touch Technology
Resolution
Max Color
5-wire resistive type
1024 x 768
16.7M
Contrast Ratio
Brightness
800:1
300 cd/m
2
Pixel Pitch
0.297mm
Viewing Angle
Response rate
140° horizontally and 140° vertically
2ms (rise time), 6ms (decay time)
Default Color Temperature 6488° K
Anti Glare Harness
Color Gamut
Backlight Units
3H
61.56%
2 CCFL
Memory
Dual-channel
DDR2 up to 4 GB capacity, 2 slots, supports 800 MHz; most configurations
ship with 1 x 2GB or 1 x 1 GB + 1 x 2 GB (3 GB)
Configurable Model: (Available in AsiaPacific region only)
1-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (1 x 1 GB)
2-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (1 x 2 GB)
2-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (2 x 1 GB)
3-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (1 x 1 GB, 1 x 2
GB)
4-GB DDR2 Synch DRAM PC2-6400 (800 MHz) Non ECC (2 x 2 GB)
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Standard Features
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
NIC
Realtek RTL8111C Ethernet Connection, 10/100/1000, with WOL support
LAN STATUS:
10MB
100MB
1000MB
Activity is occurring (Left LED ACTIVE
LED):
LED ACTIVE
LED ACTIVE
Link Status
(right LED):
None
LED On
LED On
Keyboard
Keyboard not included. PS/2 or USB supported.
NOTE: A keyboard is required to unbundle the software image.
Pointing Device
Pointing Device not included. USB supported. Pointing devices include a mouse, trackball, touch pad,
etc.
Multi Track (3) Magnetic Integrated MSR available on some select models. Conforms to ANSI/ISO 7810, 7811 1/5, 7812, and
stripe reader (MSR)
7813;
Supports OPOS and JPOS drivers layer; 3 tracks: IATA, ABA, THRIFT; bi-directional swipe, LED indicates
status of reader.
NOTE: The MSR is standard on some models and optional on others
Vacuum Fluorescent
2 line x20 character display (40 characters total), RS232 interface, DC 5Volts (V) (COM 2 port set to 5V
Display (VFD) (Customer at HP factory in BIOS setup). Supports complex character set, control commands, user-defined fonts and
Facing)
international fonts. Display pitch adjustment 80 degrees (10 degrees to 90 degrees)
WARNING: VFD must be connected to the COM 1 or COM 2 port (It should not be connected to
COM3 port because COM 3 does not support DC5V. Connecting the VFD into COM 3 port may
damage the VFD COM 1 may be used for the VFD but 5V will need to be selected in BIOS Setup for
COM 1.
NOTE: The VFD occupies COM 2 port from the HP factory. Although three COM ports are present on
the HP ap5000, COM 2 port is occupied by the VFD on factory configured models; therefore, only two
COM ports are available to the end user when the VFD is installed.
NOTE: The VFD is standard on select models and also available as an optional kit
Advertisement panel
This non-electrical panel features a clear cover. It may be removed so that print material/advertisements
can be displayed. HP provides a template for the advertisement panel.
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Standard Features
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Storage
Hard Drive or Solid State (2) 2.5" internal storage bays: 160 GB or 250GB 2.5" Hard Disk Drive
Drive
(HDD) (select models), 64 GB or 80GB 2.5" Solid State Drive (SSD) (select
models)
NOTE: The ap5000 can be configured with a combination of the 160 GB,
250 GB HDD or 64 GB, 80 GB SSD; however, if RAID 1 is requested from
the HP Factory, both storage bays must contain the same size drive.
External USB only (not included).
Optical Drive
VGA
NOTE: an optical drive is required to restore the software image.
I/O Panel
1
Warning: This is a Powered VGA Port. Do not hot plug a monitor into the VGA port. Doing so may
damage the monitor. Always power down the ap5000 when removing or attaching a monitor to the VGA
port.
USB 2.0
6: 5 (located at bottom of main display behind access panel), 1 left side
(behind access panel)
Audio line out
Microphone in
Power connector
RJ-45/Ethernet
RS232 ports
1
1
1: DC 19Volts for 130W AC power adapter
1
3: COM 1 and COM 2 (5 V configurable in BIOS), COM 3 (12V
configurable in BIOS)
NOTE: When the HP 2-line VFD is preconfigured by the HP factory,
COM 2 port is occupied. When the optional 10.4” Customer Facing
Display is installed, all three COM ports become available.
USB+power
1: 24 Volts
Keyboard (PS/2)
Parallel port
1
1
Kensington Lock Hole
2 (lock kit sold separately)
Warning: This is a Powered VGA Port. Do not hot plug a monitor into the VGA port. Doing so may
damage the monitor. Always power down the ap5000 when removing or attaching a monitor to the VGA
port.
I/O Panel Layout:
(screen side)
NOTE: I/O Panel located at rear, lower side of display under cover; I/O view when facing 15" touch
screen and bottom flipped up
Audio/Visual
Intel integrated high-definition audio with 2-channel Via VT1708S codec
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Standard Features
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Software
Preinstalled software
PDF Complete, HP Client Automation Agent
McAfee Total Protection (Windows 7 and Windows XP only)
Power Manager
Advanced Configuration and Power Management Interface (ACPI) allows the system to wake from a low
power mode.
NOTE: Power button is located on I/O panel and concealed under the I/O cover.
SMBIOS
Security
System Management BIOS, previously known as DMI BIOS, for system management information
Kensington Lock Support, (located in two places: underneath the base and on I/O panel), Power-On
password protection, Setup password protection, USB port disable.
Power Supply
130 W AC power adapter, ENERGY STAR 5.0 qualified, European Union 2005/32/EC (EUP LOT 6,
EUP LOT 7), input 90 to 260 VAC; Frequency range 47 to 63 Hz
Service and Support
Standard 3/3/3 limited warranty: 3 years parts, 3 years labor, 3 years on-site service. OS support for 90
days; quick restore solution included (requires external optical drive/not included)
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Options
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Customer Facing Displays HP 2-line x 20 characters, Vacuum Florescent Display (VFD) kit
HP 10” LCD Customer facing display kit
BV495AA
AZ191AA
Magnetic Stripe Reader
Hard Drives
HP ap5000 Magnetic Stripe Reader
BZ721AA
HP 160GB 7.2K SATA 3.0-Gb/s 2.5” Hard Disk Drive
HP 250GB 7.2K SATA 3.0-Gb/s 2.5" Hard Disk Drive
HP ap5000 64GB SATA 2.5” Solid State Drive
BS582AA
BZ724AA
BT391AA
HP 80 GB Solid State Drive for HP Business Desktop PCs
BM848AV**
NOTE: Drive caddy included with HP ap5000 base system
*Alternative if BT391AA is not available for 64GB.
Optical Drives
External USB CD/DVD R/RW Drive
FS943AA#ABA
Input/Output Devices
HP USB 2-Button Optical Scroll Mouse
HP USB Washable Keyboard
DC172AT
VF097AA
POS Peripherals
HP Heavy Duty Cash Drawer
FK182AA
BW867AA
EY022AA
BW868AA
FK224AA
FK184AA
HP Flip-Top Cash Drawer
HP Laser Barcode Scanner
HP Imaging Barcode Scanner
HP USB Single Station Thermal Receipt Printer
HP USB Multifunction Thermal Receipt Printer with MICR
Memory (DIMMs)
HP 1 GB PC2-6400 (DDR2 800 MHz)
HP 2 GB PC2-6400 (DDR2 800 MHz)
BZ722AA*
BZ723AA**
* Desktop PC memory AH058AA also compatible
** Desktop PC memory AH060AA also compatible
Security
HP Keyed Cable Lock
BV411AA
Accessories
HP ap5000 Wall Mount kit
BT390AA
EM870AA
DT527A
HP Quick Release Mechanism Kit (for use with Wall Mount Kit)
HP PS/2 Standard Keyboard
HP PS/2 2-Button Optical Scroll Mouse
HP USB-P/S2 Optical Mouse
EY703AA
DC369A
RH304AA
HP USB Optical Travel Mouse
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Technical Specifications
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
System Unit
Dimensions (HxWxD)
(12.40 x 15.79 x 9.33 in) 31.5 x 40.1 x 23.7 cm
Bottom footprint:
(W: 9.84 x D: 9.33 in) W: 25.0 x D: 23.7 cm
Weight
24.36 lb (11.05 kg)
Stand-Alone Power
Requirements
Electrical Ratings
Average Operating Power 47.3W under normal operation
90 to 264 VAC; 47 to 63 Hz
Max Operating Power
Operating
Non-operating
Operating
Operating
Non-operating
130 watts
Temperature
50° to 104° F (10 to 40° C)
-20° to 140° F (-30° to 60° C)
20 to 85%
0 to 10,000 ft (3,048 m)
0 to 30,000 ft (9,144 m)
Relative Humidity
Altitude
(unpressurized)
Industry Standard
Certifications
UL, CSA, FCC Compliance, ENERGY STAR®, EPEAT® Silver
Integrated Graphics
Media Accelerator 3000
Graphic Controller
Bus type
Integrated GMA 3000
Integrated
RAMDAC
Single 400 MHz integrated
Memory
UMA with DVMT 4.0 support for frame buffer sizes 8-256 MB
Controller clock speed
Overlay planes
Maximum Color Depth
667 MHz
One 16-bit video overlay plane
32 bpp
Maximum vertical refresh 85 Hz
rate
Multi-display Support
Dual independent monitor support through secondary VGA interface.
Primary display is 15" touch screen. Optional, secondary 10” LCD Customer
Facing Display may be attached to VGA port in I/O Panel.
Graphics/Video API
Support
DirectX 9.0c, WGF 1.0, DirectX VA 2.0, Shader Model 3.0, OpenGL 1.5
1
Resolutions Supported
Resolution
Maximum Refresh Rate (Hz)
Analog Monitor Digital Monitor
85 60
640 x 480
800 x 600
85
85
85
85
85
85
60
60
60
60
60
60-R
60-R
1024 x 768
1280 x 1024
1600 x 1200
1920 x 1080
1920 x 1200
1920 x 1440
2
2
N/A
NOTES:
1
Modes listed are supported with a single active display. The supported mode list for multiple active
displays is a subset of this list. Not all modes will support video playback and some supported modes
may use software MC (motion compensation) rather than hardware MC. Not all modes will support 3D
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Technical Specifications
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
acceleration depending on the system configuration (e.g., resolution selected, size of frame buffer,
number of installed memory modules, etc.).
2
-R denotes reduced blanking timings (some digital monitors may not support reduced blanking
timings).
2.5" 7200 RPM Serial
ATA Hard Drive
250-GB
Capacity
Height
Width
250,059,350,016 bytes
0.374 in (9.5 mm)
Media diameter: 2.5 in (63.5 mm)
Physical size: 2.75 in (70 mm)
Serial ATA (3.0 Gb/s)
Interface
Synchronous Transfer
Rate (Maximum)
Up to 3 Gb/s
Cache
8 MB
Seek Time (typical reads, Single Track
2.0 ms
12 ms
22 ms
includes controller
overhead, including
Average
Full-Stroke
settling)
Rotational Speed
Logical Blocks
7,200 rpm
488,397,168
Operating Temperature 41° to 131°F (5° to 55°C)
160-GB
Capacity
Height
Width
160,041,885,696 bytes
0.374 in (9.5 mm)
Media diameter: 2.5 in (63.5 mm)
Physical size: 2.75 in (70 mm)
Serial ATA (3.0 Gb/s)
Interface
Synchronous Transfer
Rate (Maximum)
Up to 3 Gb/s
Cache
8 MB
Seek Time (typical reads, Single Track
2.0 ms
12 ms
22 ms
includes controller
overhead, including
Average
Full-Stroke
settling)
Rotational Speed
Logical Blocks
7,200 rpm
312,581,808
Operating Temperature 41° to 131°F (5° to 55°C)
2.5" Solid State Drives
80-GB
Unformatted Capacity*
Architecture
80 GB
Multi Level Cell (MLC) NAND Flash with wear
leveling 10 channel controller
Interface type
SATA 3Gb/sec
Dimensions-external
(W x H x D)
2.74 x 0.37 x 4 in (6.98 x 0.95 x 10.2 cm)
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Technical Specifications
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Weight
0.18 lb (80 g)
Bandwidth Performance Sustained Sequential
Read
Up to 250 MB/s
Up to 70 MB/s
Sustained Sequential
Write
Random Read (4KB)
Random Write (4KB)
up to 35K IOPs
up to 6.6K IOPs
65 ms
Latency
Read
Write
85 ms
Power
Total power
consumption
0.15 Watt (Active);
0.075 Watt (Idle)
Useful drive life
5 years
35TB written, up to
20GB/day for 5 years
Environmental
(all conditions, non-
condensing)
Temperature
(operating)
32° to 158° F (0° to 70°
C)
Relative Humidity
(operating)
5% to 95%
Maximum Wet Bulb
Temperature
84° F (29° C)
(operating)
Shock (operating)
1,500 G/0.5 msec
Regulations
UL, CSA, EN 60950-2000, CISPR Pub 22 Class
B, CNS 13438, AS/NZS CISPR 22:2002 Class
B, R1113 and C1172 Class B
* For solid state disk drives, GB means 1 billion bytes. 80GB is the
unformatted capacity of this drive before a portion of the drive is reserved for
flash management features. Actual capacity will vary by content
64-GB
Unformatted Capacity
NAND Flash Memory
64 GB
Multi Level Cell (MLC) with wear leveling
controller
Interface type
SATA 3Gb/sec
Dimensions-external
(W x H x D)
2.74 x 0.37 x 4 in (6.98 x 0.95 x 10.2 cm)
Weight
0.14 lb (65 g)
Internal transfer rate
Write speed
Up to 220 MB/s
Up to 120 MB/s
Up to 150 MB/s
Read speed
Host transfer rate
Ultra DMA mode
Environmental
(all conditions, non-
condensing)
Temperature
(operating)
32° to 158° F (0° to 70°
C)
Relative Humidity
(operating)
5% to 95%
Maximum Wet Bulb
Temperature
84° F (29° C)
(operating)
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Technical Specifications
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Regulations
UL, CSA, EN 60950-2000, CISPR Pub 22 Class
B, CNS 13438, AS/NZS CISPR 22:2002 Class
B, R1113 and C1172 Class B
ROM BIOS Information
Key features of the HP BIOS in the ap5000 include:
Security – Power on password, F-10 Setup password, USB port disable,
Thermal and power management – The BIOS provides and enables thermal and power management technologies
Administrator password – Also known as the setup password, this helps prevent unauthorized changes to the system
configuration. If the administrator password is not known, the BIOS version cannot be changed and changes cannot be made
to BIOS settings using F10 setup or under the OS.
Advanced Configuration and Power Interface (ACPI) – Represents a significant innovation in power and configuration
management, allowing operating systems and applications to manage power based on activity and usage. Provides power
conservation features under Windows XP.
Ability to disable the internal speaker
Other Features
Description
ACPI-Ready Hardware
Advanced Configuration and Power Management Interface (ACPI) allows the system to wake from a low
power mode.
SMBIOS Ver. 2.4
System Management BIOS, previously known as DMI BIOS, for system management information
Dual-State Power Button Power button acts as both an on/off button and suspend-to-sleep button
Serviceability Features of System
Dual Color Power LED on Front of Computer (Indicates Normal Operations and Fault Conditions)
Diagnostic LED Explanation Table
Number of repeated red LED blinks:
2-processor thermal protection activated
3-processor not installed
4-power supply failure
5-memory error
6-video error
7-PCA failure (ROM detected failure prior
to video)
8-invalid ROM, bootblock recover mode
Flash Recovery with Video
Restore CD
DIMM Connectors for easy Upgrade
NIC LEDs (integrated)
Socketed Processor for easy Upgrade
DIMM Connectors for easy Upgrade
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Technical Specifications
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Serviceability Features of Chassis
Dual Color Power LED – To indicate normal operations and fault conditions
System memory can be upgraded
Tool-less removal power supply
Feature
Description
ASF 2.0 support (Alert Standard Format)
Industry-standard specification for network alerting and remote
control in operating system-absent environments
SMART Technology
(Self-Monitoring, Analysis and Reporting Technology)
Allows hard drives to monitor their own health and to raise flags if
imminent failures were predicted
Predicts failures before they occur. Tracks fault prediction
and failure indication parameters such as re-allocated
sector count, spin retry count, calibration retry count
By avoiding actual hard drive failures, SMART hard drives
act as "insurance" against unplanned user downtime and
potential data loss from hard drive failure
Eco-Label Certifications & This product has received or is in the process of being certified to the following approvals and may be
declarations
labeled with one or more of these marks:
US ENERGY STAR®
IT ECO declaration
registration status in your country.
Energy Consumption
Normal Operation
115 VAC
34 W
230 VAC
29 W
100 VAC
33.5 W
1 W
Sleep (Energy Star low
power mode)
1 W
1.1 W
Off
0.8 W
0.9 W
0.8 W
Heat Dissipation*
Normal Operation
Sleep
115 VAC
116 BTU/hr
3 BTU/hr
230 VAC
99 BTU/hr
4 BTU/hr
3 BTU/hr
100 VAC
115 BTU/hr
3 BTU/hr
Off
3 BTU/hr
3 BTU/hr
* Heat dissipation is calculated based on the measured watts, assuming the service level is attained for
one hour.
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Technical Specifications
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
Declared Noise Emissions
(in accordance with
ISO 7779 and ISO 9296)
System Fan
Sound Power
(LWAd, bels)
Sound Pressure
(LpAm, decibels)
Idle (Fan,
3.6
26.9
default speed)
Fixed Disk
4.4
34
(random writes)
Batteries
This battery(s) in this product comply with EU Directive 2006/66/EC
Batteries used in the product do not contain:
Mercury greater the 5ppm by weight
Cadmium greater than 10ppm by weight
Battery size: CR2032 (coin cell)
Battery type: Lithium Metal
RoHS Compliance
Material Usage
Hewlett-Packard is committed to compliance with all applicable environmental laws and regulations,
including the European Union Restriction of Hazardous Substances (RoHS) Directive. HP's goal is to
exceed compliance obligations by meeting the requirements of the RoHS Directive on a worldwide basis.
By July 1, 2006, RoHS substances will be virtually eliminated (virtually = to levels below legal limits) for
all HP electronic products subject to the RoHS Directive, except where it is widely recognized that there is
no technically feasible alternative (as indicated by an exemption under the EU RoHS Directive).
This product does not contain any of the following substances in excess of regulatory limits (refer to the
Asbestos
Certain Azo Colorants
Certain Brominated Flame Retardants – may not be used as flame retardants in plastics
Cadmium
Chlorinated Hydrocarbons
Chlorinated Paraffins
Formaldehyde
Halogenated Diphenyl Methanes
Lead carbonates and sulfates
Lead and Lead compounds
Mercuric Oxide Batteries
Ozone Depleting Substances
Polybrominated Biphenyls (PBBs)
Polybrominated Biphenyl Ethers (PBBEs)
Polybrominated Biphenyl Oxides (PBBOs)
Polychlorinated Biphenyl (PCB)
Polychlorinated Terphenyls (PCT)
Polyvinyl Chloride (PVC) – except for wires and cables, and certain retail packaging has been
voluntarily removed from most applications.
Radioactive Substances
Tributyl Tin (TBT), Triphenyl Tin (TPT), Tributyl Tin Oxide (TBTO)
2
Nickel finishes that release greater than 0.5 micro-grams/cm /week, measured according to EN
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
QuickSpecs
Technical Specifications
HP ap5000 All-in-One (AiO) Point of Sale (POS) System
1811:1998, are not used on any product surface designed to be frequently handled or touched
by users.
Packaging
HP follows these guidelines to decrease the environmental impact of product packaging:
Eliminate the use of heavy metals such as lead, chromium, mercury and cadmium in packaging
materials.
Eliminate the use of ozone-depleting substances (ODS) in packaging materials.
Design packaging materials for ease of disassembly.
Maximize the use of post-consumer recycled content materials in packaging materials.
Use readily recyclable packaging materials such as paper and corrugated materials.
Reduce size and weight of packages to improve transportation fuel efficiency.
Plastic packaging materials are marked according to ISO 11469 and DIN 6120 standards.
End-of-life Management Hewlett-Packard offers end-of-life HP product return and recycling programs in many geographic areas.
and Recycling
To recycle your product, please go to: http://www.hp.com/go/reuse-recycle or contact your nearest HP
sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each
product type for use by treatment facilities. This information (product disassembly instructions) is posted
on the Hewlett Packard web site at: http://www.hp.com/go/recyclers. These instructions may be used by
recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP
equipment.
Hewlett-Packard
For more information about HP's commitment to the environment:
Corporate Environmental Global Citizenship Report
Eco-label certifications
ISO 14001 certificates:
Copyright © 2012Hewlett-Packard Development Company, L.P.
All rights reserved. Microsoft, Windows and Windows Vista are registered trademarks or trademarks of Microsoft Corporation in the
U.S. and/or other countries. Intel, Celeron, and Core are trademarks of Intel Corporation in the U.S. and/or other countries.
The information contained herein is subject to change without notice and is provided "as is" without warranty of any kind. The
warranties for HP products are set forth in the express limited warranty statements accompanying such products. Nothing herein
should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions
contained herein.
DA - 13540
Worldwide — Version 13 — January 30, 2012
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
|