A3694A
Du a l-Bu s 4-Slot HP -HSC Exp a n sion I/O
In sta lla tion Gu id e
HP 9000/K570 En ter p r ise Ser ver s
Ed ition 1, E0797
Part No. A3694-90000
P r in ted in th e U.S.A.
J u ly, 1997
© Copyright 1997 by Hewlett-Packard Company
Download from Www.Somanuals.com. All Manuals Search And Download.
Rea d er Com m en ts
Reader Comments. We welcome your comments about our documentation. If you have
editorial suggestions or recommend improvements for this document, please write to us.
You can reach us through e-mail at: hardwaredocs@hp.cup.com or by sending your letter
to: Documentation Manager, M/ S 5657, Hewlett-Packard Company, 9000 Foothills Blvd.,
Roseville, CA 95747-5657 USA. Please include the following information in your message:
•
•
•
•
•
Title of the manual you are referencing.
Manual part number (from the title page).
Edition number or publication date (from the title page).
Your name.
Your company’s name.
SERIOUS ERRORS, such as technical inaccuracies that may render a program or a
hardware device inoperative, should be reported to your HP Response Center or directly to
a Support Engineer.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
P r efa ce
This Installation Guide contains technical information about HP 9000 Computers. The HP
9000/Kxxo family of computers includes the following models:
HP 9000/Kxx0
HP 9000 Wor k sta tion s
Ser ver s
K100
K200
K210
K220
K250
K260
K270
K370
K400
K410
K450
K460
K570
HP VISUALIZE K260-EG
HP VISUALIZE K460-EG
HP VISUALIZE K460-XP
NOTE
The Dual-Bus 4-Slot HP-HSC Expansion I/O Card may be installed ONLY on
HP9000/K570 systems.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
1 In sta lla tion P r oced u r es
HP9000/K570 systems, as with many other HP9000 systems, have a primary HP-HSC
Expansion I/O slot for upgrades. This slot is immediately to the right of the Core I/O card
as viewed from the rear of the system (refer to Figure 1).
HP9000/K570 systems can optionally use the slot to the right of the primary expansion I/O
slot for additional processors or as a secondary HP-HSC Expansion I/O slot. The A3694A
Dual-Bus 4-Slot HP-HSC Expansion I/O product adds an additional four I/O slots in this
position.
Electr osta tic Disch a r ge
CPU cards and computer systems contain assemblies and components that are sensitive to
electrostatic discharge (ESD). Carefully observe the precautions listed in this section and
use the ESD wrist strap, ESD sheet, and ESD foam pad provided in the ESD kit (part
number A3024-80004). The following precautions can significantly reduce the risk of
system failure or component damage due to ESD.
•
Always wear a grounded wrist strap when working around a system or handling the
CPU card.
•
•
Treat all assemblies, components, cards, and connections as sensitive.
When unpacking cards or components to the system, keep the item in it's conductive
bag until it is ready to be installed.
•
•
•
Keep body movement to a minimum, this generates static electricity that causes ESD.
Avoid working in carpeted areas.
Try to select a work area where potential static sources are minimized.
An ti-Sta tic Wr ist Str a p
The anti-static wrist strap is a bracelet like strip that goes around either wrist. The other
end of the strap connects to a convenient metal surface on the computer cabinet.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
An ti-Sta tic Ma t
The anti-static mat can be either the conductive bag, the ESD sheet, or the ESD foam pad.
The anti-static mat does not have to be connected to the cabinet. It should be placed close
to the computer while performing the upgrade tasks.
Tools r equ ir ed
To accomplish the upgrade procedures to the computer the following tools are required:
•
•
•
•
A Torx #10 driver. (This is the preferred tool)
A flat blade screw driver. (this can be used if a Torx driver is not available)
A3204-80004 ESD Kit
Flashlight or alternate light source (recommended but not required)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation Procedures
In sta lla tion P r oced u r es
NOTE
A 2-slot or 4-slot HP-HSC Expansion I/O product must be present in the
primary HP-HSC Expansion I/O slot before adding the A3694A product to the
secondary HP-HSC Expansion I/O slot.
1. Log Off all users and stop all active applications that may be running.
2. Perform a system backup of the entire Operating System and data base. If this is not
feasible, perform a backup of the data base. (This should be done at a scheduled interval
as common practice for protecting any new data or changes to the existing data base.)
3. Perform a system shutdown. Enter "/etc/shutdown -h" at the prompt.
4. Turn the computer key switch to the STANDBY position.
5. At the rear of the computer, unplug the power cord.
6. Remove the cover plate on the Processor/Dual Bus HP-HSC Expansion I/O slot next to
the primary HP-HSC Expansion I/O slot (see Figure 1) by loosening the two (one top
and one bottom) captive mounting screws (see Figure 2) and pulling the cover plate
away .
NOTE
Ba ck p la n e Ca r d Slot Color Cod es
The following color bars appear above the slots on the system backplane:
Color Cod es
Ta ble 1
Color
Slot
Yellow
Green
Blue
HP-PB0
HP-PB1
Core/IO
Orange
HP-HSC Expansion I/O (primary)
a
Split Magenta/Purple
Optional HP-HSC Secondary I/O
or additional Processor slots.
Purple
Processor slots.
a. HP9000/K570 systems only.
I/O and processor cards have matching color codes to assist in correctly
matching the cards to the right slots.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation Procedures
Figu r e 1
HP 9000/K570 Rea r View
7. Remove the adjoining processor slot’s cover plate by loosening the two (one top and one
bottom) captive mounting screws and pulling the cover plate away. (This is necessary to
gain access to the system board.)
8. Reach into the computer cabinet and remove the plastic dust cover from the HP-HSC
expansion connector on the system board.
9. Remove the plastic dust cover from the Dual Bus 4-Slot HP-HSC Expansion I/O Card
connector.
10.Align the Dual Bus 4-Slot HP-HSC Expansion I/O Card into the card slot and slide it
into the computer.
11.When the card makes contact with the system board connector, press the edge of the
card to fully seat the card into the computer. Tighten the two captive screws to secure
the expansion I/O card.
12.Replace the CPU cover plate and tighten the two captive mounting screws.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation Procedures
Figu r e 2
Scr ew Loca tion s
If this completes the upgrade, proceed to Upgrade Verification.
Up gr a d e Ver ifica tion
Before performing the procedures in this section, make sure that all cover plates that were
removed are reinstalled and secure. This is for proper seating of cards, as well as cooling
requirements.
1. Reconnect the power cord to the rear of the computer.
2. Turn the computer key to the ON position.
3. Observe the Front panel Display and console for any error or fault (FLT) messages.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation Procedures
When all procedures are complete, with no errors or faults, the system needs to be
re-configured to add the new HP-HSC path addresses. Refer to the Owner's Guide for
configuration instructions. The HP-HSC Slot path addresses are also the same as shown in
Table 2.
Ta ble 2
HP -HSC Slot Ad d r esses
Loca tion
Device Typ e
Ad d r ess Pa th
Core I/O card, Optional I/O connector HP-HSC I/O card
10/8 (device addr.)
P r im a r y Fou r Slot HP -HSC Exp a n sion I/O
HP-HSC I/O Expansion card, slot 0
HP-HSC I/O card
HP-HSC I/O card
HP-HSC I/O card
HP-HSC I/O card
8/0 (device addr.)
HP-HSC I/O Expansion card, slot 1
HP-HSC I/O Expansion card, slot 2
HP-HSC I/O Expansion card, slot 3
8/4 (device addr.)
8/8 (device addr.)
8/12 (device addr.)
Secon d a r y Fou r Slot HP -HSC Exp a n sion I/O (K570 on ly)
HP-HSC I/O Expansion card, slot 0
HP-HSC I/O Expansion card, slot 1
HP-HSC I/O Expansion card, slot 2
HP-HSC I/O Expansion card, slot 3
HP-HSC I/O card
HP-HSC I/O card 12/12 (device addr.)
HP-HSC I/O card 14/8 (device addr.)
HP-HSC I/O card 14/12 (device addr.)
12/0 (device addr.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|