MODEL T10044
80 LB SEED/FERTILIZER
SPREADER
INSTRUCTION SHEET
C
E
F
To reduce the risk of injury when using this
equipment:
• Do not allow anyone to operate the
spreader without proper training.
• Do not allow children to use spreader.
• Always wear proper protective gear when
using the spreader.
• If an object becomes lodged in the hop-
per, do not attempt to remove it while the
impeller is moving.
D
G
Figure 1. Inventory 1.
• Keep all hardware tightened to be sure
the spreader is in safe working order.
H
Inventory (Figures 1, 2 & 3)
A. Hopper Assembly (not shown)................... 1
B. Catch Tray (not shown).............................. 1
C. Left Wheel Frame....................................... 1
D. Right Wheel Frame .................................... 1
E. Handle Assembly ....................................... 1
F. Support Leg................................................ 1
G. Connecting Rod.......................................... 1
H. Gear Box & Axle Assembly........................ 1
I. Wheels ....................................................... 2
J. Impeller....................................................... 1
K. Hairpin Cotter Pin....................................... 1
L. Lock Nut M5-.8........................................... 1
M. Hex Bolt M5-.8 X 45................................... 1
N. Phillips Head Screw M4-.7 X 20 ................ 1
O. Hex Bolts M6-1 X 45.................................. 2
P. Inner Axle Bushings ................................... 2
Q. Hex Bolts M6-1 X 40.................................. 4
R. Axle End Covers ........................................ 2
S. Hex Bolts M6-1 X 65.................................. 4
T. Lock Nuts M6-1.......................................... 8
U. Flat Washers 6mm..................................... 4
I
J
Figure 2. Inventory 2.
L
M
K
N
P
O
R
Q
T
S
U
Figure 3. Inventory 3.
COPYRIGHT © DECEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JM10162 PRINTED IN CHINA
-1-
T10044 80 lb. Seed/Fertilizer Spreader
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Insert the hairpin cotter pin into the shaft
Operation
located inside the bottom of the hopper.
The Model T10044 can be used for spreading
fertilizers or seed. If the product has large clumps,
place the catch tray on the inner lip of the hopper
to separate out particles that could clog the impel-
ler during operation.
6. Attach the handle assembly to the support
leg using the M6-1 X 40 hex bolts and the
remaining M6-1 lock nuts.
7. Insert the steel wire head of the control cable
into the small hole located at the end of the
lever assembly. To make sure that the holes
in the bottom of the hopper align with the
holes in the adjustable plate; fully push the
lever down and check the inside of the hop-
per to make sure that the adjustable plate is
closed. Clamp the control cable into the press
plates by removing and re-installing the two
Phillips head screws and lock nuts, as shown
in Figure 7.
The impeller should move in a clockwise rotation.
If it does not, disassemble and make sure that
the hole in the gearbox axle is on the right hand
side as stated in Step 2, and the protrusion on the
gearbox is facing towards the back as stated in
Step 3. To evenly distribute product, the spreader
should be walked at a brisk pace.
During operation, push the handle downwards to
lessen the amount of product being distributed
and pull up to increase. The wing nut on the lever
assembly, as shown in Figure 7, can be adjusted
to facilitate a maximum product distribution for the
current spreading task.
Wing Nut
Maintenance
To prevent unnecessary wear, the Model T10044
should be regularly maintained. Thoroughly clean
the inside of the hopper, adjustable plate and the
impeller after every use. Product that is left over
and not removed can impede the impeller during
future uses. Clean with warm soapy water and
rinse thoroughly.
Press Plate
Steel Wire
Check the pressure level of the tires before use.
The maximum pressure for the tires is 24 PSI.
Figure 7. Control lever assembly.
The gears in the gear box assembly were lubri-
cated at the factory. Do not open the gear box or
dirt may enter and clog the gears.
-3-
T10044 80 lb. Seed/Fertilizer Spreader
Download from Www.Somanuals.com. All Manuals Search And Download.
T10044 Parts Breakdown
��
�
��
��
�
��
�
�
��
�
��
��
�
��
��
�
�
��
�
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
Download from Www.Somanuals.com. All Manuals Search And Download.
T10044 Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
PCB27M
CARRIAGE BOLT M6-1 X 25
EXT TOOTH WASHER 6MM
27 PT10044027 RIGHT WHEEL ASSEMBLY FRAME
28 PT10044028 SPECIAL DISC
PTLW05M
PT10044003 SCALE PLATE
29 PT10044029 RIGHT WHEEL
PT10044004 ADJUSTMENT LEVER
PT10044005 RIGHT HALF HANDLE
PT10044006 LEFT HALF HANDLE
31 PT10044031 AXLE END COVER
32 PT10044032 INNER AXLE BUSHING
33 PT10044033 OUTER AXLE BUSHING
34 PT10044034 GEAR BOX AND AXLE ASSEMBLY
PS01M
PHLP HD SCR M4-.7 X 18
PT10044008 HANDLE GRIP
PT10044009 SPACER
35 PS52M
36 PB172M
PHLP HD SCR M4-.7 20
HEX BOLT M5-.8 X 45
10 PWN01M
WING NUT M6-1.0
37 PT10044037 TOP LINE CLAMP PLATE
38 PT10044038 CONTROL CABLE
11 PT10044011 HOPPER
12 PT10044012 HAIRPIN COTTER PIN
13 PT10044013 CENTER COVER
39 PS09M
40 PT10044040 SPECIAL WASHER
41 PW03M FLAT WASHER 6MM
PHLP HD SCR M5-.8 X 10
14 PB171M
HEX BOLT M6-1 X 65
15 PT10044015 ADJUSTABLE PLATE
42 PT10044042 HANDLE
16 PW05M
17 PS02M
FLAT WASHER 4MM
43 PT10044043 HOPPER LINE CLAMP
PHLP HD SCR M4-.7 X 12
44 PS20M
PHLP HD SCR M5-.8 X 15
18 PT10044018 LEFT WHEEL ASSEMBLY FRAME
19 PT10044019 IMPELLER
45 PT10044045 LARGE END CAP
46 PT10044046 SMALL END CAP
47 PT10044047 CONNECTING ROD
20 PB52M
HEX BOLT M6-1 X 35
LOCK NUT M5-.8
21 PLN02M
48 PB71M
HEX BOLT M6-1 X 45
22 PT10044022 BOTTOM LINE CLAMP PLATE
23 PT10044023 TUBE END CAP
49 PT10044049 LEFT WHEEL
50 PT10044050 GRIZZLY.COM LABEL
24 PB47M
HEX BOLT M6-1 X 40
LOCK NUT M6-1
51 PW05M
FLAT WASHER 4MM
25 PLN03M
52 PT10044052 CATCH TRAY
26 PT10044026 SUPPORT LEG
Download from Www.Somanuals.com. All Manuals Search And Download.
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
|