10" HEAVY-DUTY TABLE SAW
MODEL G1023S & G1023S110
INSTRUCTION MANUAL
COPYRIGHT © FEBRUARY 2002 BY GRIZZLY INDUSTRIAL, INC
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
REVISED NOVEMBER 2002, PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE
MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF
THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS
ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1.
SAFETY
PAGE
SAFETY RULES FOR ALL TOOLS....................................................................................................................2-3
ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS..............................................................................4
AVOIDING KICKBACK ..........................................................................................................................................5
SAFETY ACCESSORIES ..................................................................................................................................5-6
2.
3.
INTRODUCTION
COMMENTARY ....................................................................................................................................................7
CIRCUIT REQUIREMENTS
G1023S110 ............................................................................................................................................................8
G1023S ..................................................................................................................................................................9
GROUNDING ......................................................................................................................................................10
EXTENSION CORDS ..........................................................................................................................................10
MACHINE FEATURES
TERMS & DEFINITIONS ................................................................................................................................11-12
MAIN FEATURES ................................................................................................................................................12
SET UP
4.
5.
UNPACKING........................................................................................................................................................13
PIECE INVENTORY ......................................................................................................................................13-14
HARDWARE RECOGNITION CHART ................................................................................................................15
CLEAN UP ..........................................................................................................................................................16
SITE CONSIDERATIONS....................................................................................................................................16
BEGINNING ASSEMBLY ....................................................................................................................................17
EXTENSION WINGS ......................................................................................................................................17-18
FENCE & RAILS ..................................................................................................................................................18
SWITCH ..............................................................................................................................................................18
CLEANOUT DOOR..............................................................................................................................................19
MOTOR BRACE ..................................................................................................................................................19
GUARD BRACKET ..............................................................................................................................................20
HANDWHEEL ......................................................................................................................................................21
TABLE INSERT....................................................................................................................................................21
SAW BLADE ........................................................................................................................................................22
BLADE GUARD/SPLITTER ............................................................................................................................22-24
MITER GAUGE ....................................................................................................................................................25
START UP............................................................................................................................................................26
RECOMMENDED ADJUSTMENTS ....................................................................................................................26
OPERATIONS
6.
7.
BLADE SELECTION ......................................................................................................................................27-28
CROSSCUTTING ................................................................................................................................................29
RIPPING ..............................................................................................................................................................30
DADO OPERATIONS ....................................................................................................................................31-33
RABBET OPERATIONS ................................................................................................................................33-34
MAINTENANCE
GENERAL ............................................................................................................................................................35
LUBRICATION ....................................................................................................................................................36
TABLES................................................................................................................................................................36
V-BELT............................................................................................................................................................36-37
MAINTENANCE LOG ..........................................................................................................................................38
SERVICE AGREEMENT
45˚ & 90˚STOPS ..................................................................................................................................................39
BLADE PARALLELISM ..................................................................................................................................40-41
BLADE ALIGNMENT ......................................................................................................................................42-43
WIRING DIAGRAM ........................................................................................................................................44-45
CLOSURE....................................................................................................................................................................46
8.
9.
DATA SHEET ............................................................................................................................................................................47
PARTS BREAKDOWNS & LIST............................................................................................................................................48-50
TROUBLESHOOTING................................................................................................................................................................51
PUSH STICK PATTERN ............................................................................................................................................................52
WARRANTY AND RETURNS ..............................................................................................................................................54-56
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury, or MAY cause property
damage.
This symbol is used to alert the user to useful information about
proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
1. KEEP GUARDS IN PLACE and in working
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors should be
kept at a safe distance from work area.
order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning on.
6. MAKE WORKSHOP CHILD PROOF with
padlocks, master switches, or by removing
starter keys.
3. KEEP WORK AREA CLEAN. Cluttered
7. DO NOT FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS ENVI-
RONMENT. Do not use power tools in
damp or wet locations, or where any flam-
mable or noxious fumes may exist. Keep
work area well lighted.
8. USE RIGHT TOOL. Do not force tool or
attachment to do a job for which it was not
designed.
-2-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD. Make
sure your extension cord is in good condi-
tion. Conductor size must be in accor-
dance with the chart below. The amperage
rating is listed on the motor or tool name-
plate. An undersized cord will cause a drop
in line voltage resulting in loss of power
and overheating. Your extension cord must
also contain a ground wire and plug pin.
Always repair or replace damaged exten-
sion cords.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubri-
cating and changing accessories.
15. DISCONNECT TOOLS before servicing
and changing accessories, such as blades,
bits, cutters, and any other item.
16. REDUCE THE RISK OF UNINTENTION-
AL STARTING. Make sure switch is in off
position before plugging in. Also, the mag-
netic switch on this machine may start if the
switch gets bumped hard enough.
Minimum Gauge for Extension Cords
LENGTH
AMP RATING
0-6
25ft
16
16
16
14
12
10
50ft 100ft
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury.
16
16
16
12
12
10
16
14
14
12
10
No
7-10
11-12
13-16
18. CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part
that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, bind-
ing of moving parts, breakage of parts,
mounting, and any other conditions that
may affect its operation. A guard or other
part that is damaged must be properly
repaired or replaced.
17-20
21-30
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear
is recommended. Wear protective hair cov-
ering to contain long hair.
11. ALWAYS USE ANSI-APPROVED SAFE-
TY GLASSES. Also use face or dust mask
if cutting operation is dusty. Everyday eye-
glasses only have impact resistant lenses,
they are NOT safety glasses.
19. NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN POWER OFF. Do not
leave tool until it comes to a complete stop.
20. NEVER USE UNDER THE INFLUENCE of
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It is safer than
using your hand and frees both hands to
operate tool.
alcohol or drugs, or when tired.
21. IF AT ANY TIME YOU ARE EXPERIENC-
ING DIFFICULTIES performing the intend-
ed operation, stop using the machine!
Then contact our service department or
ask a qualified expert how the operation
should be performed.
13. NEVER OVERREACH. Keep proper foot-
ing and balance at all times.
G1023S Series Heavy-Duty 10'' Table Saw
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions For Table Saws
1. THRU-SAWING: Use blade guard, splitter,
and anti-kickback fingers on all thru-saw-
ing operations. See Page 12 for the defin-
ition of thru-sawing.
8. CROSSCUTTING: Move the rip fence out
of the way when crosscutting.
9. MITER GAUGE/RIP FENCE: Never use
the miter gauge and rip fence at the same
time.
2. KICKBACK: Use anti-kickback devices
during ALL cutting operations. If you do not
have a complete understanding of how
kickback occurs, or how to prevent it, Do
not operate this table saw. See Page 12
for the definition of kickback.
10. STALLED BLADE: Never attempt to free a
stalled saw blade without first turning the
saw off.
11. CUTOFF TABLES: Use adequate support
to the rear and sides of the saw table for
wide or long workpieces.
3. DANGEROUS REACHING: Do not reach
behind or over the saw blade with either
hand while the saw is running.
12. HAND SAFETY: Avoid awkward cutting
operations and hand positions where a
sudden slip could cause your hand to move
into the saw blade.
4. PUSHSTICK: Use a push stick when rip-
ping narrow stock.
5. FREE-HAND CUTTING: The fence or the
miter gauge must support the workpiece
during all cutting operations.
13. SAW BLADE: Lower the saw blade below
the table when not in use.
6. BODY POSITION WHEN CUTTING: Do
not stand or have any part of your body in-
line with the path of the saw blade.
14. DAMAGED SAW BLADE: Never use a
damaged saw blade or one that has been
dropped.
7. WORKPIECE CONTROL: Hold the work-
piece firmly against the miter gauge or
fence and hold the workpiece firmly
against the table.
15. DADO CUTTING: There is a high degree
of risk involved with any dado operation.
See Page 12 for the definition of dado.
Unfamiliarity with this manual could result
in serious personal injury. Become familiar
with the contents of this manual, including
all the safety warnings.
No list of safety guidelines can be com-
plete. Operating this machinery may
require additional safety precautions spe-
cific to your shop environment. Failure to
use reasonable caution while operating
this machine could result in serious per-
sonal injury.
-4-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Avoiding Kickback
Safety Accessories
Failure to understand how and why kick-
back occurs could cause serious person-
al injury. DO NOT operate this table saw if
you do not have a clear understanding of
kickback, and how it occurs.
Not using safety accessories could cause
serious personal injury. Learn how to cor-
rectly use each safety accessory.
Push Sticks
The use of push sticks, particularly when cutting
small or narrow workpieces, provides a double
benefit for saw operators. The push stick pro-
vides added leverage, enabling the operator to
keep the workpiece firmly supported against the
fence and table. At the same time, the push stick
keeps the operator’s hand safely away from the
rotation of the saw blade as shown in Figure 1.
See the template on Page 53 of the manual for
construction details, or purchase one from the
Grizzly catalog or website.
Statistics prove that most common accidents
among table saw users can be linked to kick-
back.
Kickback is typically defined as the high-speed
expulsion of stock from the table saw toward its
operator.
In addition to the danger of the operator or oth-
ers in the area being struck by the flying stock, it
is often the case that the operator’s hands are
forced into the blade during the kickback.
The following can help minimize kickbacks:
• Use your blade guard and splitter.
• Never for any reason place your hand behind
the blade. Should kickback occur, your hand
will be pulled into the blade.
• Inspect splitter for alignment between it and
your blade.
• Never use the fence as a guide for crosscut-
ting.
• Never attempt freehand cuts.
• Use a push stick or featherboard to maintain
control of your workpiece.
• Feed cuts through to completion.
• Stand to the side when ripping.
• Ensure your fence and miter slot are parallel to
the blade.
Figure 1. Push Stick.
If you do not have a clear understanding of kick-
back and how it occurs, do not operate this table
saw.
G1023S Series Heavy-Duty 10'' Table Saw
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Zero Clearance Table Inserts
Push Paddles
Ideal for use when ripping thin strips or making
bevel cuts, these prevent tearout and jammed
blades by supporting material close to the blade.
Push paddles provide added leverage and sup-
port when ripping or crosscutting wide work-
pieces as shown in Figure 3. We offer a number
of push paddles in the Grizzly catalog.
Use the standard table insert as a template when
creating additional inserts from wood or plywood.
Slots can be custom cut for specific blade angles
by raising the running blade into an uncut insert
at the angle you desire. Be sure to make an addi-
tional slot for the blade splitter.
We also carry a wide selection of table inserts
(Figure 2) in the Grizzly catalog or website. Be
sure to hold the insert firmly in place with a piece
of wood when creating slots. Never hold the table
insert with your hand while cutting new slots.
Figure 3. Push Paddles.
Featherboards
Easily made from scrap stock, featherboards pro-
vide an added degree of protection against kick-
back as shown in Figure 4. To make a feather-
board, cut a 30-40° angle at one end of the board
and make a number of end cuts at approximately
1
⁄4" apart and 2" to 3" deep. We also offer a num-
ber of featherboards in the Grizzly catalog.
Figure 2. Zero Clearance Table Inserts.
Figure 4. Featherboards.
-6-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INTRODUCTION
Most importantly, we stand behind our machines.
Commentary
If you have any service questions or parts
requests, please call or write us at the location
listed below:
We are proud to offer the Grizzly Model G1023S
Series Table Saw. The Model G1023S Series is
part of a growing Grizzly family of fine wood-
working machinery. When used according to the
guidelines set forth in this manual, you can
expect years of trouble-free, enjoyable operation
and proof of Grizzly’s commitment to customer
satisfaction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: techsupport@grizzly.com
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G1023S Series Table Saws as supplied when the
manual was prepared. However, owing to
Grizzly’s policy of continuous improvement,
changes may be made at any time with no oblig-
ation on the part of Grizzly. Current Grizzly
machine manuals can be viewed and printed at:
The Model G1023 Series is an industrial grade
table saw intended for professional use. Features
include cast iron trunnions, triple V-belt drive,
magnetic switch, and the Shop Fox® Classic
Fence. The G1023S110 features a 2 HP dual
voltage, TEFC motor that is prewired for 110V.
The G1023S features a 3 HP 220V, TEFC motor.
Grizzly offers many accessories for the table
saws including blades, extension rails, outfeed
rollers and mobile bases. Please refer to the cur-
rent Grizzly catalog or website for prices and
ordering information.
Lack of familiarity with
this manual could
cause serious person-
al injury. Become
familiar with the con-
tents of this manual,
including all the safety
warnings.
Grizzly is also pleased to provide this manual
with the Model G1022 Series Table Saws. It was
written to guide you through assembly, review
safety considerations, and cover general operat-
ing procedures. If you have any comments
regarding this manual, please write to us at the
address below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
G1023S Series Heavy-Duty 10'' Table Saw
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: CIRCUIT REQUIREMENTS
Model G1023S110 Only:
110V Operation
220V Operation
The Model G1023S110 motor is prewired to oper-
ate at 110V. When operating at 110V, use a
NEMA-style 5-30 plug and outlet. See Figure 5.
Check the electrical codes in your area for
specifics on wiring requirements.
The motor supplied with the Model G1023S110
can be operated at either 110V or 220V. The
motor comes prewired for 110V. Refer to the
wiring diagram insert supplied with this manual for
information about converting to operate at 220V.
Under normal 110V use, the motor draws approx-
imately 24 amps. Use a 30 amp circuit breaker or
a 30 amp slow-blow fuse. The circuit you use
should be dedicated, (i.e., the Model G1023S110
should provide the only draw from that circuit). If
frequent circuit failures occur when using this
machine, contact our Service Department or your
local electrical contractor.
If converting to operate at 220V, a suitable 220V
plug and magnetic switch must be wired in. When
operating at 220V, use a NEMA-style 6-15 plug
and outlet. See Figure 6. Check the electrical
codes in your area for specifics on wiring require-
ments. You will also need to replace the existing
110V switch with a magnetic 220V switch such as
the Grizzly Model G4572.
Because of the high amperage draw of this
machine when wired for 110V, standard house-
hold circuit wiring may not be of a large enough
gauge. A qualified electrician must install a new
circuit with wires capable of handling a 30 amper-
age draw. Do not attempt to modify an existing cir-
cuit by replacing the circuit breaker with one rated
for a higher amperage.
Under normal use, the motor draws approximate-
ly 12 amps at 220V. Use a 15 amp circuit break-
er for 220V operation This should be satisfactory
for normal use while providing enough protection
against circuit damage caused by power surges.
Always check to see if your current wires are
capable of handling a 15 amp load. If you are
unsure, consult the advice of a qualified electri-
cian. Do not attempt to modify an existing circuit
by replacing the circuit breaker with one rated for
a higher amperage.
Figure 5. NEMA 5-30 110V plug and outlet.
Figure 6. NEMA 6-15 220V plug and outlet
-8-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Model G1023S Only:
220V Operation
The Model G1023S motor is wired to operate at
220V. When operating at 220V, use a NEMA-
style L6-20 plug and outlet. See Figure 7. Check
the electrical codes in your area for specifics on
wiring requirements.
Under normal 220V use, the motor draws approx-
imately 18 amps. Use a 20 amp circuit breaker or
a 20 amp slow-blow fuse. The circuit you use
should be dedicated, (i.e., the Model G1023S
should provide the only draw from that circuit). If
frequent circuit failures occur when using this
machine, contact our Service Department or your
local electrical contractor.
Figure 7. NEMA L6-20 220V plug and outlet
Because of the high amperage draw of this
machine, standard household circuit wiring may
not be of a large enough gauge. A qualified elec-
trician must install a new circuit with wires capa-
ble of handling a 18 amperage draw. Do not
attempt to modify an existing circuit by replacing
the circuit breaker with one rated for a higher
amperage.
G1023S Series Heavy-Duty 10'' Table Saw
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding
Extension Cord
Should it be necessary to use an extension make
sure the cord is rated Hard Service (grade S) or
better. Refer to the chart in Section 1: Safety
Instructions to determine the minimum gauge for
the extension cord. The extension cord must also
contain a ground wire and plug pin. Always repair
or replace extension cords when they become
worn or damaged.
Electrocution or a fire
can result if the band-
saw is not grounded cor-
rectly. Make sure all
electrical circuits are
grounded. Do not use
the machine if it is not
grounded.
NOTICE
The wire on the power cord with green or
green and yellow striped insulation is the
grounding conductor.
No single list of electrical guidelines can
be comprehensive for all shop environ-
ments. Operating this machinery may
require additional electrical upgrades spe-
cific to your machine and shop environ-
ment. It is your responsibility to make sure
your electrical systems comply with all
local electrical codes and ordinances.
In the event of an electrical short, grounding pro-
vides electric current a path of least resistance to
reduce the risk of electrical shock to the operator.
Ground the power cord and this machine in accor-
dance with all local codes and ordinances.
Operating this machine when it is not properly
grounded can result in electric shock or electro-
cution.
-10-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: MACHINE FEATURES
Kerf: The resulting cut or gap made by a saw
Terms & Definitions
blade.
Kickback: A condition in which the wood is
The following is a list of common definitions,
thrown back towards an operator at a high rate
terms and phrases used throughout this manual
of speed.
as they relate to this table saw and woodworking
in general. It is important that you read and
Miter Gauge: A component that controls the
become familiar with them before assembling,
wood stock movement while performing a
adjusting or operating this machine. Your safety
crosscut. Allows for variation of angle cuts
is VERY important to us at Grizzly!
such as miter cuts used on a picture frame.
Arbor: Metal shaft extending from the drive
Moulding Head: A cutterhead attached to the
mechanism, to which the cutting blade is
arbor that accepts interchangeable moulding
attached.
knives for profile cutting. We DO NOT recom-
mend the use of moulding head cutters.
Bevel Edge Cut: Tilting the saw arbor and blade
to an angle between 0° and 45° to perform an
angled cutting operation.
Parallel: Being an equal distance apart at every
point. i.e. the rip fence face is parallel to the
side face of the saw blade.
Blade Guard: Metal or plastic mechanism that
mounts over the saw blade to prevent acciden-
tal contact with the cutting edge.
Non-Thru Cut: A sawing operation that requires
the removal of the blade guard and splitter.
Dado and rabbet cuts are considered Non-
Thru Cuts because the blade does not pro-
trude above the top face of the wood stock.
Always remember to reinstall the blade guard
Crosscut: Table saw operation in which the miter
gauge is used to cut across the grain of a piece
of wood.
and splitter after performing a non-thru cut.
Dado Blade: Blade or set of blades that attach to
the arbor and are used for cutting grooves and
rabbets.
Perpendicular: Intersecting and forming right
angles; at right angles to the vertical and hori-
zontal planes. i.e. the blade is perpendicular to
the table surface.
Dado Cut: Table saw operation that uses a dado
blade to cut a flat bottomed groove into the
face of wood stock.
Push Paddle: Safety aid used to push a piece of
wood stock through a cutting operation.
Featherboard: Safety device used to keep the
workpiece against the rip fence or table during
a cutting operation. The featherboard also
Push Stick: Safety aid used to push a piece of
wood stock through a cutting operation.
allows the operator to keep his/her hands at a
Usually used when rip cutting.
safe distance away from the saw blade while
cutting the workpiece.
Rabbet: Cutting operation that creates an L-
shaped channel along the edge of wood stock.
G1023S Series Heavy-Duty 10'' Table Saw
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Splitter: Metal plate attached to the back of the
blade guard that maintains the kerf opening in
the wood when performing a cutting operation.
Main Features
1
Set up and operation instructions will be easier to
understand if you become familiar with the loca-
tion and names of the basic features.
Standard Kerf: ⁄8" gap made with a standard
blade.
Straightedge: A tool used to check the flatness,
Match up the feature list below with the letters in
Figure 8 to identify the table saw feature loca-
tions.
parallelness, or consistency of a surface(s).
Thru-Sawing: A sawing operation where the
wood stock thickness is completely sawn
through. Proper blade height usually allows 1⁄4
of the top of the blade to extend above the
wood stock.
"
H
G
F
I
A
Thin Kerf: 3⁄32" gap made with a thin kerf blade.
Rip Cut: A cut made along the grain of the wood.
Sacrificial Fence: A piece of wood attached to
the face of the rip fence that is designed to
extend the fence face away from the metal por-
tion of the fence. Used primarily when making
rabbet cuts with a dado blade.
B
E
C
D
Figure 8. The front of the table saw.
A. Extension Wing
B. On/Off Switch
C. Blade Height Handwheel
D. Base
E. Blade Angle Handwheel
F. Rip Fence Rails
G. Rip Fence
H. Blade Guard/Splitter Assembly
I. Miter Gauge
-12-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: SET UP
Unpacking
Piece Inventory
The Model G1023S Series Table Saws are
shipped from the manufacturer in carefully
packed boxes. If you discover the machine is
damaged after you have signed for delivery,
immediately call our Customer Service for advice.
When you are completely satisfied with the con-
dition of your shipment of boxes, you should
inventory their parts.
Sharp edges on metal
parts may cause person-
al injury. Examine the
edges of all metal parts
before handling.
The
Series is
Model
G1023S
heavy
a
machine, weighing up to
360 lbs. Personal injury
could occur if the
machine is moved with-
out additional assis-
tance. Seek the help
friends when moving or
lifting the machine.
Figure 9A. Shop Fox® Classic fence compo-
nents.
G1023S Series Heavy-Duty 10'' Table Saw
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
11
12
10
9
3
4
7
8
6
5
Figure 9B. G1023S Series component layout.
After all the parts have been removed from the
box, you should have:
The hardware bag should contain the follow-
ing:
1. Extension Wings (2)
(1) 3mm Allen Wrench
(1) 4mm Allen Wrench
2. Miter Gauge
5
(1) Combo Wrench 5⁄8
"
3.
⁄8"-18 Blade Guard Mounting Shaft
(1) 5⁄8"-18 Blade Guard Mounting Shaft
(1) 5⁄8"-18 Hex Nut
4. Arbor Wrench
5
5.
⁄8" Combo Wrench
(4) #8 x 3⁄8" Self Tapping Screw
(4) #8 Flat Washer
6. Blade Guard Assembly
7. Handwheel Knob Bolt
8. Handwheel Handle
9. Dado Blade Table Insert
10. Standard Blade Table Insert
11. Cleanout Door
12. Hardware Bag
13. Table Saw Unit (Not Shown)
-14-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Recognition Chart
Use this chart to match up
hardware pieces during the
assembly process!
Lock
Nut
Wing
Nut
5
⁄
8''
#10
Countersunk
Phillips
Head
Thumb
Screw
1
⁄4''
Phillips
Head
Slotted
Screw
Screw
Screw
5⁄16''
9⁄16''
3
⁄8''
Carriage
Bolt
Button
Head
Screw
Cap
Screw
Flange
Bolt
7⁄16''
1
⁄
2''
Phillips
Head
Sheet
Metal
Screw
Phillips
Head
Hex
Hex
Head
Bolt
1
⁄2''
Setscrew
Washer
Bolt
7⁄16''
D
5
⁄
8''
Hex
Nut
Lock
Washer
12mm
4mm
6mm
3
⁄
8''
5mm
1
3
1
5
⁄
⁄
⁄
⁄
''
4''
8''
2''
5
7
9
3
7
⁄
⁄
⁄
⁄
⁄
''
16''
16''
16''
10mm
15mm
20mm
25mm
30mm
35mm
40mm
45mm
50mm
55mm
60mm
65mm
70mm
75mm
8
4mm
8mm
4''
18''
5⁄16''
10mm
11⁄4''
11⁄2''
13⁄4''
2
21⁄4''
21⁄2''
23⁄4''
3
10mm
1
⁄
4''
12mm
16mm
6mm
8mm
#10
G1023S Series Heavy-Duty 10'' Table Saw
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean Up
Site Considerations
The unpainted surfaces are coated with a waxy
oil to protect them from corrosion during ship-
ment. Remove this waxy oil with a solvent clean-
er or citrus-based degreaser such as Grizzly’s
G7895 Degreaser. To clean thoroughly, some
parts may need to be removed. The machine
will operate best when the waxy oil is
removed from all moving and sliding parts.
Chlorine-based cleaners and solvents will dam-
age the painted surfaces of the machine. Follow
the manufacturer’s instructions when using any
type of cleaning product.
Floor Load
The Model G1023S Series Table Saws are a
heavy load with a medium footprint. Most com-
mercial or home shop floors should be sufficient
to carry the weight of the machine. Reinforce the
floor if you question its ability to support the
weight.
Working Clearance
Working clearances can be thought of as the dis-
tances between machines and obstacles that
allow safe operation of every machine without lim-
itation. Consider existing and anticipated machine
needs, size of material to be processed through
each machine, and space for auxiliary stands or
work tables. Also, consider the relative position of
each machine to one another for efficient materi-
al handling. Be sure to allow yourself sufficient
room to safely run your machines in any foresee-
able operation and keep dust collection hoses off
the floor and out of the way.
Gasoline or petroleum
products used to clean
the machinery could
explode causing serious
personal injury. DO NOT
use gasoline or petrole-
um products to clean the
machinery.
Lighting
Lighting should be bright enough to eliminate
shadows and prevent eye strain. Electrical circuits
should be dedicated or large enough to handle
combined motor amp loads. Be sure to follow
local electrical codes for proper installation of new
lighting or circuits.
Smoking near solvents
could ignite an explosion
or fire causing serious
injury. DO NOT smoke
while using solvents.
Unsupervised
children
and visitors entering a
shop could receive seri-
Lack of ventilation while
using solvents could
cause serious personal
health risks, fire, or
environmental hazards.
Always work in a well
ventilated areas to pre-
vent the accumulation
of dangerous fumes.
Supply the work area
with a constant supply
of fresh air using a fan.
ous
personal
injury.
Ensure child and visitors
safety by keeping all
entrances to the shop
locked at all times. DO
NOT allow unsupervised
children or visitors in the
shop at any time.
-16-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Beginning Assembly
Extension Wings
The table and the wings
represent a very heavy
load. DO NOT over-exert
yourself while lifting or
moving the table and the
wings – get assistance.
Keep clothing rolled up
and out of the way of
machinery and keep
hair pulled back.
To attach the extension wings to the saw:
Disconnect power to the
machine when perform-
1. Attach the left wing to the table using the (3)
!
3
⁄
8"-16 x 11⁄4" Hex Bolts and 3⁄8" Flat Washers
ing any maintenance or
assembly. Failure to do
this may result in serious
personal injury.
provided. Adjust the wing reasonably flush
with the table and do not tighten the bolts
completely at this time.
2. Attach the right wing to the table using the
3
3
(3) ⁄8"-16 x 11⁄4" Hex Bolts and ⁄8" Flat
Washers provided. Adjust the wing reason-
ably flush with the table and do not tighten
the bolts completely at this time.
Wear safety glasses dur-
ing the entire assembly
process. Failure to com-
ply may result in serious
personal injury.
3. Align the top of the wings flush with the table
top directly above the front bolts and flush
with the front edge of the table. Tighten the
front bolts.
Some metal parts may
have sharp edges on
them after they are
formed. Please examine
the edges of all metal
parts before handling
them. Failure to do so
could result in injury.
4. Raise or lower the rear of the extension
wings until the middle of the wings are flush
with the table top. Tighten the middle bolts.
5. Raise or lower the rear of the wings until the
wings and table are flush. Tighten the rear
bolts.
6. Re-check the flushness of the wings against
the table above each bolt. Re-adjust if nec-
essary.
TOOLS REQUIRED: You will need a high quality
square, a long straightedge, 10mm, 12mm,
14mm open end wrenches and a 3mm Allen®
wrench.
G1023S Series Heavy-Duty 10'' Table Saw
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Check the alignment of the table and both
wings with a straightedge. The straightedge
should run flat across both wings and the
table top. If the straightedge contacts both
wings and the table evenly, you are finished
with this section. If the straightedge does not
contact them evenly, continue to Step 9.
Fence & Rails
Your Model G1023S Series comes with a Shop
Fox® Brand Fence & Rails. Refer to the manual
included in the fence box for assembly instruc-
tions.
8. If the extension wings tilt up or down at the
outside edges, remove the wings and shim
them with masking tape as shown in Figure
10.
A) If a wing tilts down, stick layers of mask-
ing tape along the bottom edge of the
table and retighten.
Switch
The switch comes prewired to the motor and can
be easily mounted to the rail.
B) If a wing tilts up, stick layers of masking
tape along the top edge of the wing and
retighten. Allow the tape to extend above
table surface and trim the extended tape
with a sharp knife after final assembly.
To mount the switch:
1. Line the switch bracket holes up with the
holes on the underside of the rail.
9. Re-check the alignment of the table and both
wings with a straightedge and re-adjust if
necessary.
2. Secure the switch and bracket to the under-
side of the rail using the (2) 1⁄4"-20 x 3⁄8"Phillip
Head Screws and 1⁄4" Lock Washers.
3. Disconnect the machine from the power
source!
4. Connect the plug on the cord between the
switch and motor.
Masking Tape
Figure 10. Using tape to shim for wing alignment.
-18-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleanout Door
Motor Brace
The Model G1023S Series comes with a cleanout
door that can accept the optional Model G1838 4"
dust hood. Mount the cleanout door into the
square hole on the lower left side of the saw base
A red motor brace has been installed for shipping
purposes. Remove this brace before continuing
with assembly. The bolts that secure the brace
should be screwed back in at the locations from
which they came.
as shown in
.
Figure 11a
Motor Brace
Installed For
Shipping Only!
Cleanout Door
Figure 11b. Motor brace.
Figure 11a. Installed cleanout door.
G1023S Series Heavy-Duty 10'' Table Saw
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Guard Bracket
To install the blade guard assembly:
5
1.
⁄8"-18 blade guard mounting
Thread the
shaft into the mounting location on the back
of the table saw base as shown in Figure
12.
2.
Secure the blade guard mounting shaft with
the included 5⁄16"-18 hex nut.
Blade Guard
Mounting Shaft
3. Slide the loosely assembled bracket onto
the blade guard mounting shaft and tem-
porarily hand tighten the nuts as shown in
Figure 12. Attaching the 5
⁄
8"-18 blade guard
mounting shaft.
.
Figure 13
Blade Guard
Mounting Bracket
Figure 13. Blade guard mounting bracket
-20-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Set the table insert into the recessed area on
Handwheel
the table surface.
4. Ensure that all four table insert setscrews
One handwheel has been removed for shipping.
To install, place the handwheel over the threads
and screw the lock knob into the center. Next
insert the handle into the handwheel and tighten
it as shown in Figure 14. Install the other handle
onto the other handwheel.
(
are firmly in contact with the
Figure 15)
table casting.
5. Using an allen wrench, raise or lower each of
the four setscrews until the insert is flush
with the table top.
6. Using the side handwheel, position the blade
90° to the table surface.
7. Wearing leather gloves, rotate the blade while
raising and lowering it through its full range of
motion. Make sure it never contacts any part
of the table insert.
8. Repeat Step 6 with the blade in the 45° posi-
tion.
Figure 14. Tightening handle onto handwheel.
Table Insert
The table insert provides support for the material
being cut. It must be installed flush with the cast
iron table surface.
Figure 15. Setscrews on each corner of insert.
To install the table insert:
1. Disconnect the machine from the power
source!
2. Using the front handwheel, move the blade
to its lowest position.
G1023S Series Heavy-Duty 10'' Table Saw
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
Saw Blade
Blade Guard/Splitter
To install a saw blade:
To install a blade guard/splitter:
1. Disconnect the machine from the power
source!
1. Disconnect the machine from the power
source!
2. The arbor nut has left-hand threads.
Loosen the arbor nut clockwise and remove
the outside flange from the arbor. Remove
2. Slip the blade guard/splitter over the mount-
ing bolts as shown in Figure 17. The wash-
ers should be between the bolt head and the
slots. Tighten the bolts to secure the blade
guard/splitter.
3
and discard the ⁄4'' diameter spacer on the
arbor shaft.
Use caution and remain
alert when working with
the saw blade. Failure
to follow this warning
could result in serious
Blade Guard
personal
death.
injury
or
3. Install the saw blade onto the arbor. Ensure
that the blade teeth point toward you as you
stand at the front of the saw.
Mounting Bolt
4. Slide on the flange and thread the arbor nut
Anti-kickback Pawl
back on.
Figure 17. Blade guard and splitter in place.
5. Use the arbor wrench provided with the saw
to tighten the arbor nut. Wedge a block of
wood in the teeth of the blade to keep it from
turning when tightening the nut as shown in
Figure 16.
3. Set a machinist’s square against the face of
the blade splitter. Slightly rotate the rear
bracket to adjust the face of the blade splitter
perpendicular to the table top as shown in
Figure 18.
!
!
Figure 16. Changing saw blade.
Figure 18. Blade splitter square to table.
-22-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Add washers
here to move
back of split-
ter to the left.
Use caution and remain
alert when working
around the saw blade.
Failure to follow this
warning could result in
serious personal injury
or death.
Add washers
here to move
front of split-
ter to the left.
Splitter
Blade
4. Next, set a straightedge against the face of
the saw blade and the blade splitter as
shown in Figure 19. If the blade splitter is
properly aligned, please skip ahead to Page
26; otherwise, continue with the next step.
Figure 20. Improper splitter/blade alignment.
!
Adjusted
Rear Splitter
Adjustment
Screw
Front Support
Bracket
Proper Alignment
Added Washers
Figure 19. Guard in line with blade.
Figure 21. Proper splitter/blade alignment.
5. If the blade splitter is to the right of the blade
as shown in Figure 20, simply add washers
between the splitter and the front mounting
bracket, and adjust the rear splitter support
as shown in Figure 21.
G1023S Series Heavy-Duty 10'' Table Saw
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Adjustment Bolt
6. Recheck the splitter alignment to the blade
and to the table top. Adjust as necessary and
tighten all the bolts before use. If the blade
guard is properly aligned, please skip ahead
to Step 13; otherwise, continue with the next
step.
7. If the splitter is positioned to the left of the
blade, alignment cannot be achieved by
washer placement. Adjustment of the front
support bracket is required. See Figure 20
for adjustment details. Loosen the 2 adjust-
ment screws and move left or right.
Arbor Bracket
8. If this adjustment does not allow enough
movement of the splitter, remove the table
and wings, and set them to one side. Be sure
to note the position of the table shims.
Replace them to their original position before
re-attaching the table.
Figure 22. Arbor bracket adjustment locations.
11. Moving the arbor bracket moves the V-belts
and pulleys out of alignment, so adjustment
of the motor pulley is required. Simply loosen
the setscrew in the middle groove of the pul-
ley, and slowly slide the pulley toward the
end of the motor shaft. Once the V-belts are
back in alignment, tighten the setscrew
securely.
The table and wings
represent a very heavy
load. DO NOT over-
exert yourself while lift-
ing or moving the table
and wings – get assis-
tance.
12. Recheck the guard alignment to the blade
and to the table top. Adjust as necessary and
tighten down all the bolts before use. If the
blade guard is properly aligned, re-attach the
table, making sure there is adequate blade
clearance through all blade adjustments.
The arbor bracket and motor pulley now need
to be adjusted:
13. Adjust the blade to 45°. Raise and lower it
through the full range. Re-adjust the blade to
90°, then raise and lower it through the full
range. There should be no contact between
the blade, the base, the table insert, or any
other part of the saw. If there is contact,
repeat Steps 8-12.
9. Loosen the adjustment bolt shown in Figure
22, and slowly slide the arbor bracket
towards the end of the shaft. Only move the
arbor bracket a distance equal to the amount
of misalignment between the blade and the
splitter, or a little more. You can always
adjust the splitter back to the left with wash-
ers.
10. Tighten the adjustment bolt securely.
-24-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
7. To adjust to 45˚, follow Steps 1-6 while using
Miter Gauge
an adjustable square.
8. After rotating the miter body from 45˚ to 90˚
and back a few times, double check your
adjustments at both angles to ensure that
you have accurately set your miter gauge.
The miter gauge for the Model G1023S Series
has two setscrews in the miter bar which can be
set to remove any loose movement between the
miter bar and the T-slot.
To adjust the miter gauge:
1. Loosen or tighten the two miter bar
setscrews ( ) until the miter gauge
Figure 23
Setscrew
slides freely in the slot, but has no loose
movement.
2. Loosen the lock knob on the miter gauge and
place a square against the face of the miter
body and the miter bar.
Stop Link
Stop Screw
3. Adjust the miter body until there is no space
between the square and the miter bar.
Jam Nut
4. Tighten the lock knob.
Figure 23. Miter gauge adjustment points.
5. With the stop link ( ) in the up posi-
Figure 23
tion, loosen the jam nut and adjust the stop
screw until it is seated against the stop link.
6. Loosen the setscrew on the left front side of
the miter bar, adjust the pointer to 90˚ and
retighten the setscrew.
G1023S Series Heavy-Duty 10'' Table Saw
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Start Up
Recommended
Adjustments
For your convenience, the adjustments listed
below have been performed at the factory and no
further setup is required to operate your machine.
Loose hair and clothing
could get caught in
machinery causing seri-
ous personal injury.
Keep loose clothing
rolled up and long hair
tied up and away from
machinery.
However, because of the many variables
involved with shipping, we recommend that you
at least check the following adjustments to
ensure the best possible results from your new
machine.
All of these adjustments are covered in step-by-
step detail in Section 8: Service Adjustments.
Projectiles thrown from
the machine could cause
serious eye injury. Wear
safety glasses during
assembly.
Recommended adjustment checklist:
• 45˚ & 90˚ Stops (Page 39)
• Blade Parallelism (Page 41)
• Blade Alignment (Page 42)
Before starting the machine:
1. Read this manual and make sure you take all
safety precautions before operating this
machine.
2. Make sure the blade guard and splitter have
been correctly installed and are adjusted
properly as shown on Pages 23-25.
3. Make sure that any tools or foreign objects
have been removed from the machine.
4. Review Section 3: Circuit Requirements
beginning on Page 8 and make sure all
wiring is correct.
5. Keep your finger on the STOP button during
the entire test run of the machine.
Starting the machine:
Turn the machine on and make sure your hand is
on the STOP button in case you need to shut the
machine off immediately. The machine should
run smoothly with little or no vibration.
-26-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: OPERATIONS
Wear safety glasses. a dust mask, and
hearing protection while the machine is
running. Failure to do this could result in
serious personal injury.
Blade Selection
Figure 25. Crosscutting blade.
Combination Blade: Used for cutting with and
across the grain. A compromise between a rip
blade and a cross-cut blade, a 10" combination
blade will typically have between 40-50 teeth
(Figure 26), an alternate top bevel and flat or
alternate top bevel (Figure 29) and raker tooth
profile. The teeth are arranged in groups of five.
The gullets are small and shallow within the
groups of five teeth, similar to a cross-cut blade;
then large and deep between the groups, like a
ripping blade.
Choosing the correct blade for the job is essential
for the safe and efficient use of your table saw.
Rip Blade: Used for cutting with the grain. 10" rip
blades have between 20-40 teeth (Figure 24),
flat-top ground tooth profile (Figure 29) and large
gullets to allow for large chip removal.
Figure 24. Ripping blade.
Cross-cut Blade: Used for cutting across the
grain. 10" cross-cut blades have between 60-80
teeth (Figure 25), alternate top bevel or steep
alternate top bevel tooth profiles (Figure 29),
small hook angle and a shallow gullet.
Figure 26. Combination blade.
G1023S Series Heavy-Duty 10'' Table Saw
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
Plywood Blade: Used for cutting plywood or
veneers. 10" plywood blades have 40-80 teeth
(Figure 27), a steep alternate top bevel tooth pro-
file (Figure 29) and very shallow gullet.
Figure 28. Optional dado blade.
• Wobble Dado Blade—Also a dedicated dado
blade, a wobble blade usually consists of a sin-
gle blade that is tilted on the arbor shaft while it
is spinning. The channel is cut in the face of the
workpiece as the blade passes through its pre-
adjusted width of travel. Wobble blades are an
inexpensive option when visibly pleasing chan-
nels are not a concern.
Figure 27. Plywood blade.
Thin-kerf: Designed for saws with smaller
motors and for reducing material waste, thin-kerf
blades are thinner than standard blades.
Performance and accuracy can be maintained by
the use of blade stabilizers.
Moulding Heads: A moulding head is a cutter-
head that attaches to the arbor and holds individ-
ual moulding knives. They should only be used by
professional woodworkers with training beyond
the scope of this manual.
This section on blade selection is by no means
comprehensive. Always follow the saw blade
manufacturer's recommendations to ensure safe
and efficient operation of your table saw.
Some blade guards/splitters are thicker
than thin-kerf blades. DO NOT use the thin-
kerf blade if this is the case or serious per-
sonal injury could result.
Dado Blades: There are two types of dado
blades: stacked and wobble.
• Stacked Dado Blade—These dedicated dado
cutting blades consist of a set of up to 8 indi-
vidual blades. Multiple cutters are "stacked"
between two outside blades. The width of the
dado is determined by the combination of cut-
ters that are “stacked” together. The dado is cut
in a single pass leaving a smooth and square
channel in the face of the workpiece as shown
on Page 31. Stacked dado blades are the most
expensive option but are worth considering if
your projects require a lot of visible dado cuts.
A typical stacked dado blade is shown in
Figure 28.
Figure 29. Various saw tooth cutting profiles.
-28-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Turn on the saw and allow it to come to full
Crosscutting
speed.
7. Hold the workpiece firmly against the face of
the miter gauge and ease it into the blade as
shown in Figure 30.
A crosscut is a cut against the grain direction of
the workpiece. Crosscutting man-made wood
products like plywood is performed by cutting par-
allel to the shortest side.
Turn off the saw and allow the blade to
come to a complete stop before removing
the cut-off piece. Failure to follow this warn-
ing could result in serious personal injury
Keep the blade guard in
the down position at all
times. Failure to do this
could result in serious
personal injury or death.
To make a 90˚ crosscut using the miter gauge:
1. Adjust the miter gauge to the 90˚ position.
2. Adjust the fence completely away from the
cutting operation.
3. Position the miter gauge in one of the two
miter slots.
4. Adjust the blade height so the highest saw
1
tooth protrudes approximately ⁄4" above the
workpiece.
Figure 30. Typical cross-cut operation.
5. Hold the workpiece against the miter gauge
and line up the cut with the blade.
G1023S Series Heavy-Duty 10'' Table Saw
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
Ripping
Stand to the left of the blade line-of-cut
when ripping a board. Serious personal
injury could occur if kickback results.
A rip cut is a cut with the grain direction of the
workpiece. Ripping man-made wood products
like plywood is performed by cutting parallel to
the longest side.
8. Using a push stick, feed the workpiece
through the saw blade as shown in Figure
31, until the workpiece is completely past the
saw blade. When a small width is to be
ripped and a push stick cannot be safely put
between the blade and rip fence, rip a larger
piece to obtain the desired piece.
Keep the blade guard in
the down position at all
times. Failure to do this
could result in serious
personal injury or death.
To make a rip cut:
1. Set the fence to the desired width of cut on
the fence rail scale.
2. Adjust the blade height so the highest saw
1
tooth protrudes approximately ⁄4" above the
workpiece.
3. Joint one long edge of the workpiece on a
jointer.
4. Set up any safety devices such as feather-
boards or other anti-kickback devices.
Figure 31. Typical ripping operation.
5. With the saw disconnected from the
power source, rotate the blade to make
sure it does not come into contact with any of
the safety devices.
Turn off the saw and allow the blade to
come to a complete stop before removing
the cut-off piece. Failure to follow this warn-
ing could result in serious personal injury
6. Plug the saw into the power source, and turn
on the saw and allow it to come to full speed.
7. The jointed edge of the workpiece must be
slide against the fence during the cutting
operation.
-30-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Dado Cutting
Commonly used in furniture joinery, a dado is a
straight channel cut in the face of the workpiece.
Dadoes can be cut using either a dado blade
(Figure 28) or a standard saw blade.
Dado operations present very real hazards
requiring proper procedures to avoid seri-
ous injury. The chance of kickback is
always greater when dado blades are used
so extra care must be taken. Any movement
of the stock away from the fence will cause
kickback. Be certain that stock is flat and
straight. Failure to follow these warnings
could result in serious personal injury.
Figure 32. Single-blade dado cut.
Never allow hands or arms to be above or
behind the saw blade. Should kickback
occur, the hands and arms could be pulled
into the saw blade causing serious person-
al injury.
To use a stacked or wobble dado blade:
1. Disconnect the machine from the power
source!
2. Remove the table insert, splitter guard, and
regular saw blade.
Always use push sticks, featherboards,
push paddles and other safety accessories
whenever possible to increase safety and
control during operations which require the
blade guard and splitter to be removed from
the saw. Failure to follow this warning could
result in serious personal injury.
3. Attach and adjust the dado blade system as
recommended in the dado blade manufac-
turer’s instructions.
4. Install the dado table insert.
5. Raise the dado blade up to the desired depth
of cut (depth of dado channel desired).
7. Reconnect the saw to the power source.
8. With one finger ready to push the OFF but-
ton, turn the saw on. The blade should run
smooth with no vibrations or wobbling.
Never perform a through cut operation with
a dado blade. A dado blade was designed to
make non-through cuts only. Failure to fol-
low this warning could result in serious per-
sonal injury.
9. When the blade has reached full speed, per-
form a test cut with a scrap piece of wood.
6. If dadoing along the long length of your work-
piece, adjust the distance between the fence
and the inside edge of the blade to suit your
needs as shown in Figure 32.
G1023S Series Heavy-Duty 10'' Table Saw
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
10. If the cut is satisfactory, repeat with your fin-
ish stock.
Never allow hands or arms to be above or
behind the saw blade. Should kickback
occur, the hands and arms could be pulled
into the saw blade causing serious person-
al injury.
ALWAYS replace the blade guard after
dadoing is complete. Failure to follow this
warning could result in serious personal
injury.
Using a standard saw blade:
Always use push sticks, featherboards,
push paddles and other safety accessories
whenever possible to increase safety and
control during operations which require the
blade guard and splitter to be removed from
the saw. Failure to follow this warning could
result in serious personal injury.
1. Clearly mark the width of the dado cut on
your workpiece. Include marks on the edge
of your workpiece so you can clearly identify
your intended cut while the material is laying
flat on the saw table.
2. Raise the blade up to the desired depth of
cut (depth of dado channel desired).
4. Turn on the saw and allow the blade to reach
full speed.
3. If dadoing along the long length of your work-
piece, adjust the fence so the blade is
aligned with the inside of your dado channel
as shown in Figure 33.
5. Perform a test cut on a scrap piece of wood.
Determine if the depth of cut is correct.
6. If the cut is satisfactory, repeat with your fin-
ish stock.
Always turn the saw off and wait until the
blade has come to a complete stop before
adjusting the fence. Failure to follow this
warning could result in serious personal
injury.
Figure 33. Single-blade dado cut.
-32-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Re-adjust the fence so the blade is aligned
with the other edge of the intended dado
channel. Be sure to keep the cuts within your
marks; otherwise, the dado will be too big.
Rabbet Cutting
Commonly used in furniture joinery, a rabbet is a
straight groove cut in the edge of the workpiece.
Rabbets are best cut using a standard saw blade.
8. Continue making cuts toward the center of
the dado with your subsequent cuts until the
dado is complete.
Rabbet operations present very real haz-
ards requiring proper procedures to avoid
serious injury. Any movement of the stock
away from the fence will cause kickback. Be
certain that stock is flat and straight. Failure
to follow these warnings could result in
serious personal injury.
Always replace the blade guard after dado-
ing is complete. Failure to follow this warn-
ing could result in serious personal injury.
Cutting rabbets with the standard blade:
Cutting rabbets with a standard saw blade DOES
NOT require the use of a sacrificial fence.
1. Clearly mark the width of the rabbet cut on
your workpiece. Include marks on the edge
of your workpiece so you can clearly identify
your intended cut while the material is laying
flat on the saw table.
2. Raise the blade up to the desired depth of
cut (depth of rabbet channel desired).
3. If the rabbet runs the length of the material,
adjust the fence so the blade is aligned with
the inside of your rabbet channel as shown
in Figure 34.
Figure 34. Rabbet cutting.
G1023S Series Heavy-Duty 10'' Table Saw
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Rotate the workpiece as shown in
.
Figure 35
8. Perform the second cut to complete the rab-
Never allow hands or arms to be above or
behind the saw blade. Should kickback
occur, the hands and arms can be pulled
into the saw blade. Serious personal injury
could result.
bet cut.
Always use push sticks, featherboards,
push paddles and other safety accessories
whenever possible to increase safety and
control during operations which require the
blade guard and splitter to be removed from
the saw. Failure to follow this warning could
result in serious personal injury.
Figure 35. Rabbet cutting.
4. Turn the saw on.
5. When the blade has reached full speed, per-
form a test cut with a scrap piece of wood.
Always replace the blade guard after dado-
ing is complete. Failure to follow this warn-
ing could result in serious personal injury.
6. If the cut is satisfactory, repeat with your fin-
ish stock.
Always turn the saw off and wait until the
blade has come to a complete stop before
adjusting the fence. Failure to follow this
warning could result in serious personal
injury.
-34-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: MAINTENANCE
General
Regular periodic maintenance on your Model
G1023S Series Table Saw will ensure its optimum
performance. Make a habit of inspecting your
Disconnect power to
the machine when per-
forming any mainte-
nance on the table saw.
!
machine each time you use it.
Failure to do this could
result in serious per-
sonal injury.
Check for the following conditions and repair
or replace when necessary:
1. Loose mounting bolts.
2. Worn switch.
Loose hair and clothing
could get caught in
machinery causing seri-
3. Worn or damaged cords and plugs.
ous personal injury.
4. Damaged V-belt.
Keep loose clothing
rolled up and long hair
5. Any other condition that could hamper the
tied up and away from
safe operation of this machine.
machinery.
6. Inspect blades for damage.
7. Guard alignment and operation.
Projectiles thrown from
the machine could cause
serious eye injury. Wear
safety glasses during
maintenance.
G1023S Series Heavy-Duty 10'' Table Saw
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
Table
The sealed ball bearings in the motor and
throughout the Model G1023S Series require no
maintenance during their lifetime. When they do
wear out, replacements can be obtained through
the Grizzly Parts Department.
The table is made from cast iron. If preventative
measures are not taken, the table surface will rust.
Regularly wipe sawdust from the table to prevent
rust causing moisture from becoming trapped
against the table. Regular applications of products
like SLIPIT® will prevent rust as the saw is used on
a daily basis. For long term storage, use products
such as Boeshield T-9®. Both of these products
are available in the Grizzly catalog.
Lubricate the areas indicated below every 12
months:
BLADE ANGLING TRUNNION—The front and
back trunnions each have a semi-circle groove
that needs to be lubricated with an automotive
wheel bearing grease.
BLADE HEIGHT TRUNNION—The blade height
trunnion pivots on a steel rod. This should be
lubricated with 6 or 7 drops of light machine oil.
V-Belt
To ensure optimum power transmission from the
motor to the blade, the V-belts must be in good
condition and operate under the proper tension.
When replacing V-belts, replace all three at the
same time—even if they do not all appear worn.
WORM GEARS These should be lubricated
—
with an automotive wheel bearing grease.
Belt tension should be checked at least every 3
months; more often if using the table saw inten-
sively.
The V-belts are accessed through the cavity on
the right side of the saw. They link the arbor and
motor pulleys.
To check V-belt tension:
1. Disconnect the machine from the power
source!
2. With moderate pressure, push the center of
each V-belt.
3. Note the amount of deflection. Deflection
1
should be approximately ⁄2", similar to
Figure 36.
-36-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace the V-belts:
!
1. Disconnect the machine from the power
source!
2. Remove the blade.
3. Adjust the arbor so it is up all the way and in
the 90° position.
4. Place a board under the motor and loosen
the motor mount bolt. Slowly lower the arbor
until the motor rests on the board, allowing
the belts to be loose on the pulleys.
Figure 36. V-belt deflection.
To adjust V-belt tension:
5. Pull off the old V-belts and replace them with
new ones. Have the number from the belt
ready when calling the service department
for replacements.
1. Disconnect the machine from the power
source!
6. Raise the arbor and remove the board to
2. Loosen the motor mount bolt.
adjust the V-belt tension.
3. Shift the motor up or down to increase or
decrease the V-belt tension. Tighten the
motor mount bolt.
7. Tighten the motor mount bolt.
4. Check the V-belt tension again. Ensure that
the motor pulley and arbor pulley are lined
up.
G1023S Series Heavy-Duty 10'' Table Saw
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Log
Maintenance Performed
Date
Approximate Hours Of Use
-38-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: SERVICE ADJUSTMENTS
45˚ & 90˚ Stops
Disconnect power to the
machine when perform-
ing any maintenance,
assembly or adjust-
ments. Failure to do this
may result in serious
personal injury.
1. Set your blade angle at zero as shown on the
angle indicator on the front of the saw and
raise the blade several inches above the
table.
!
2. Place a machinist’s square flat on the table
and slide it alongside the blade. The square
should contact the blade evenly from bottom
to top. Make sure that a blade tooth does not
obstruct the movement of the square.
Keep loose clothing
rolled up and out of the
way of machinery and
keep hair pulled back.
3. Adjust the handwheel until the square is
flush with the blade. Loosen the tilt indicator
arrow, set to zero, and retighten. Loosen and
adjust the stop bolt on the left side of the
front trunnion to allow a 90° stop point. See
Figure 37 for details.
Wear safety glasses
during the entire adjust-
ment process. Failure
to comply may result in
serious personal injury.
4. Turn the blade angle handwheel until the
angle indicator points at the desired angle.
5. Tighten the handwheel locking knob.
6. Repeat Steps 1-6 for setting the blade to 45°
and adjust the 45° stop bolt on the right side
of the front trunnion. Use the 45° side of a
combo square or a bevel gauge set at 45°.
45˚ Stop Bolt
90˚ Stop Bolt
Figure 37. Geared trunnion.
G1023S Series Heavy-Duty 10'' Table Saw
-39-
Download from Www.Somanuals.com. All Manuals Search And Download.
6. If the blade tip does not touch the end of the
adjustable square similar to the first mea-
surement, then the table will need to be
adjusted.
Blade Parallelism
Your table saw will give the best results if the
miter slot and the rip fence are adjusted parallel
to the blade. If either of these are not exactly par-
allel, your cuts and your finished work will be
lower in quality, but more important, this condition
increases the risk of kickback. Take the time to
adjust your table saw properly. A few minutes
now will be time well spent.
7. To adjust the table, loosen the four bolts in
the table mounting locations (see Figure 39)
and slightly tap the table. Repeat Steps 1-5
until satisfactory. Do not forget to tighten the
table mounting bolts when finished.
1. Disconnect the machine from the power
source!
2. Use an adjustable square to measure the
distance from the miter slot to a carbide tip
on the blade as shown in Figure 38. Make
sure that the face of the adjustable square is
even along the miter slot.
Table Mount Holes
3. With the end of the adjustable square just
touching the tip, lock the square in place.
Now, mark the carbide tip with a magic mark-
er where you made this measurement.
Figure 39. Table mounting bolt holes.
4. Rotate that tip to the other end of the table
insert.
8. Now check to see if the blade remains paral-
lel to the miter slot when tilted to 45°.
5. Slide the adjustable square down to the
other end of the table insert, and compare
the distance from the marked blade tip to the
end of the adjustable square.
9. Tilt the blade to 45° and repeat Steps 1-5. If
the blade is still parallel to the miter slot, con-
tinue on to the “Miter Gauge” instructions.
Otherwise, continue with the next step.
!
10. If the blade was parallel to the miter slot at
90° but not at 45°, the table will need to be
shimmed with metal shim stock. The shims
are placed between the table and cabinet
over each of the four table mounting bolts
Use caution and remain
alert when working
around the saw blade.
Failure to follow this
warning could result in
serious personal injury
or death.
Figure 38. Adjusting blade to miter slot.
-40-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Refer to Figures 40 & 41, for shim place-
ment. If the distance of A is shorter than B,
shim(s) will need to be placed under corners
#1 and #2. If the distance of B is shorter than
A, shim(s) will need to be placed under cor-
ners #3 and #4. Very thin shim stock works
well, just make sure they are all the same
thickness, and you put an equal number
under each of the two corners.
!
45˚ Bevel
#1 Shim
#4 Shim
12. Tighten down one bolt a small amount and
then move on to each of the others, tighten-
ing each down the same amount. Continue
to rotate through the bolts, tightening them a
little each time until they are all secure.
#2 Shim
#3 Shim
13. Now recheck the blade to miter slot at 90°
and 45° by repeating Steps 1-5. If the dis-
tance of A and B are equal, continue to the
“Miter Gauge” instructions. If the distances
are still off, repeat Steps 9-12.
Figure 40. 45°
blade parallelism measurement.
!
45˚ Bevel
#1 Shim
14. Once you feel you have the miter slot adjust-
ed to the blade, recheck all measurements
and be sure the table mounting bolts are
secure. Repeat Step 12 on Page 25. If the
table is removed in the future, be sure to re-
install the shims the same way they came
off.
#4 Shim
#2 Shim
#3 Shim
Figure 41. 45°
blade parallelism measurement.
G1023S Series Heavy-Duty 10'' Table Saw
-41-
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Reattach the table, making sure there is ade-
quate blade clearance through all blade
adjustments. Recheck guard alignment to
the blade and to the table top. Adjust as nec-
essary and tighten down all the bolts before
use.
Blade Alignment
The blade position can be adjusted slightly in
case it contacts the table insert when raised or
tilted. This adjustment can be made either by
moving the whole trunnion assembly, or by just
moving the arbor bracket. Try adjusting by mov-
ing the whole trunnion first, this is the easier of
the two ways.
5. If the blade is still contacting the insert,
repeat Steps 1-4. Check all other adjust-
ments.
6. Recheck the blade to miter slot adjustments,
To adjust the blade position by moving the
trunnion:
and adjust as necessary.
Bracket Lock Bolt
1. Disconnect the machine from the power
source!
2. Remove the table and wings and set them to
one side. Be sure to note the position of the
table shims. Replace them to their original
position before re-attaching the table.
3. Loosen the four trunnion mounting bolts as
shown in Figure 42, and nudge to either the
left or right depending on where the blade is
hitting the saw.
Arbor Bracket
Figure 43. Adjusting arbor bracket.
To adjust the blade position by moving the
arbor bracket:
Trunnion Mount Bolts
1. Disconnect the machine from the power
source!
2. Remove the table and wings and set them to
one side. Be sure to note the position of the
table shims. Replace them to their original
position before re-attaching the table.
3. Loosen the bracket lock bolt shown in
Figure 42. Trunnion mounting bolts.
Figure 43.
4. Slowly slide the arbor bracket towards the
end of the shaft.
The table and wings rep-
resent a very heavy
load. DO NOT over-
exert yourself while lift-
ing or moving the table
and wings – get assis-
tance.
NOTICE
If you make the adjustment described in
this section, check and adjust the blade
splitter to make sure it aligns with the
blade.
-42-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Moving the arbor bracket moves the V-belts
and pulleys out of alignment, so adjustment
of the motor pulley is required. Simply loosen
the setscrew in the middle motor groove pul-
ley and slowly slide the pulley towards the
end of the motor shaft. Once the V-belts are
back in alignment, tighten the setscrew
securely.
6. Re-attach the table, making sure there is
adequate blade clearance through all blade
adjustments. Recheck guard alignment to
the blade and to the table top. Adjust as nec-
essary and tighten down all the bolts before
use.
7. If the blade is still contacting the insert,
repeat Steps 1-6. Check all other adjust-
ments.
8. Recheck the blade to miter slot adjustments,
and adjust as necessary.
G1023S Series Heavy-Duty 10'' Table Saw
-43-
Download from Www.Somanuals.com. All Manuals Search And Download.
-44-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
11
13
14
G1023S Series Heavy-Duty 10'' Table Saw
-45-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9: CLOSURE
The following pages contain general machine
data, parts diagrams/lists, a troubleshooting guide
and Warranty/Return information.
We recommend you keep a copy of our current
catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
machine, or if you need general assistance or
replacement parts, please contact the Service
Department at the location listed below.
If you need parts or help in assembling your
machine, or if you need operational information,
call the Grizzly Service Department. Trained ser-
vice technicians will be glad to help you.
Grizzly Industrial, Inc.
1203 Lycoming Circle
Muncy, PA 17756
If you have any comments regarding this manual,
please write to Grizzly at the address below:
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: techsupport@grizzly.com
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines, and your local
library are good places to start.
Important safety measures that are essential to
the operation of this machine have been
explained in Section 1: Safety. While most safety
measures are generally universal, Grizzly
reminds you that each workshop is different and
safety rules should be considered as they apply to
your specific situation.
-46-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
GRIZZLY MODELS G1023S & G1023S110 TABLE SAWS
Design Type......................................................................................................................10" Tilting Arbor
Maximum Diameter of Saw Blade ......................................................................................................10"
Diameter of Arbor..................................................................................................................................5⁄8
Capacities:
"
Maximum Depth of Cut at 90° ........................................................................................................31⁄8
"
"
Maximum Depth of Cut at 45° ........................................................................................................21⁄8
Maximum Rip to Right of Blade (Standard)......................................................................................26"
Maximum Rip to Right of Blade (Optional) ......................................................................................46"
Maximum Rip to Left of Blade ..........................................................................................................11"
Distance Front of Table to Center of Blade......................................................................................17"
Table in Front of Blade at Maximum Cut..........................................................................................12"
Maximum Width of Dado ................................................................................................................13⁄16"
Overall Dimensions:
With Wings and Guide Bars........................................................................................50" W x 315⁄16" D
Weight (Shipping)......................................................................................................................460 lbs.
Construction:
Table ..........................................................................................................Precision Ground Cast Iron
Stand ..........................................................................................................................Pre-formed Steel
Miter Gauge ............................................................................................................Cast Iron/Steel Bar
Trunnions ................................................................................................................................Cast Iron
Table:
Height ..............................................................................................................................................34"
Size....................................................................................................................27" Deep x 201⁄8" Wide
Size w/Extension Wings......................................................................................27" Deep x 401⁄8" Wide
Miter Gauge Groove Type ............................................................................................................T-slot
Spindle Bearings ..........................................................................Sealed and Lubricated-For-Life/Ball
Motor:
Type ....................................................................................................TEFC Capacitor Start Induction
Horsepower G1023S ....................................................................................................................3 HP
Horsepower G1023S110 ..............................................................................................................2 HP
Power Transfer ............................................................................................................Triple Belt Drive
Phase / Cycle ......................................................................................................Single Phase / 60 HZ
Voltage G1023S ............................................................................................................................220V
Voltage G1023S110 ..........................................................................................................110V / 220V
Amps G1023S ................................................................................................................................18A
Amps G1023S110..................................................................................................................24A / 12A
Motor R.P.M..........................................................................................................................3450 RPM
Blade R.P.M..........................................................................................................................4140 RPM
Bearings ..................................................................................Shielded and Lubricated-For-Life / Ball
Switch ................................................................................Magnetic with Thermal Overload Protector
Specifications, while deemed accurate, are not guaranteed.
G1023S Series Heavy-Duty 10'' Table Saw
-47-
Download from Www.Somanuals.com. All Manuals Search And Download.
A
A
A
A
C
A
B
A
A
A
A
D
A
A
A
A
C
Download from Www.Somanuals.com. All Manuals Search And Download.
REF# PART#
DESCRIPTION
REF# PART#
DESCRIPTION
001 P1023001
002 P1023002
003 P1023003
004 P1023004
005 PV02
CABINET
SCALE
056 P1023056
56C P1023056C MOTOR 2 HP 110/220V
57A PB76
058 PB03
060 PB07
061 PW07
062 P1026062
063 P1023063
064 PRP03
065 PSB14
066 PW02
67A PK02M
068 P1023068
069 PLN05
070 P1023070
071 P1023040
072 P1023072
079 PSS07
MOTOR 3 HP 220V
SELF TAPPING SCREW
CLEANOUT DOOR
HEX NUT 5⁄16"-18
HEX NUT 3⁄8"-16
DOOR LATCH
HEX BOLT 5⁄16"-18 X 15⁄8
HEX BOLT 5⁄16"-18 X 1"
"
HEX BOLT 5⁄16"-18 X 3⁄4
FLAT WASHER 5⁄16"
SUPPORT BRACKET
FLANGE CASTING
"
05A PN08
006 P1023006
07A P1023007A KNOB 3⁄8"-16 X 11⁄2
"
008 P1023008
009 P1023009
010 P1023010
011 PSS04
12A PSB65
013 P1023013
14A PS27
015 P1023015
016 P1023016
017 P1023017
018 PS05
HAND WHEEL LOCK
HANDLE
HAND WHEEL
ROLL PIN 5⁄16" X 5⁄8
"
CAP SCREW 3⁄8"-10 X 1"
FLAT WASHER 3⁄8
KEY 5 X 5 X 40
SHAFT
"
SETSCREW 1⁄4"-20 X 5⁄16"
CAP SCREW 10-24 X 2"
POINTER BRACKET
PHLP HD SCR 5⁄16"-18 X 3⁄8
POINTER
LOCK NUT 3⁄4"-16
"
REAR TRUNNION
LOCK NUT 5⁄8"-18
FRONT TRUNNION
PLATE
BLADE GUARD SUPPORT
SETSCREW 1⁄4"-20 X 1⁄2
"
PHLP HD SCR 5⁄16"-18 X 1"
80-1 P1023080-1 SPRING CLIP
80-2 PS06
019 PB16
020 PLW04
021 PN08
HEX BOLT 3⁄8"-16 X 11/2
"
PHLP HD SCREW 10-24 X 3⁄8''
LOCK WASHER 3⁄8
HEX NUT 3⁄8"-16
"
80B P1023080B STD TABLE INSERT
80D P1023080D DADO INSERT
081 P1023081
82A PLW04
083 PB24
084 P1023084
85A PLW07
85B PN13
85C PW01
85D PLW05
086 PB77
087 G8291(2HP) SWITCH G1023S110
87A G4573(3HP) SWITCH G1023S
088 P1023088
089 PK02M
090 PS201-1
91C PS08
91A PW03
91B PN07
093 PSS02
094 P1023094
095 P1023095
96A PSS08
96B P1023096
097 P1023097
098 P1023098
099 P1023099
100 P1023100
101 P1023101
102 P1023102
103 P1023103
104 P1023104
105 P1023105
22A PSS03
023 P1023023
024 P1023024
025 PSS05
026 P1023026
027 P1023027
28A PK02M
029 P1023029
030 PN02
SETSCREW 1⁄4"-20 X 3⁄8
WORM
"
TABLE
LOCK WASHER 3⁄8
"
COLLAR
HEX BOLT 3⁄8"-16 X 11⁄4
EXTENSION WING
"
SETSCREW 5⁄16"-18 X 1⁄4
SHAFT
"
LOCK WASHER 1⁄2
HEX NUT 1⁄2"-13
"
PIN
KEY 5 X 5 X 40
GEARED TRUNNION
HEX NUT 5⁄16"-18
HEX BOLT 5⁄16"-18 X 1"
FLANGE
FLAT WASHER 1⁄2
"
LOCK WASHER 7⁄16"
HEX BOLT 7⁄16"-20 X 1"
031 PB03
032 P1023032
033 P1023033
035 P1023035
036 PB16
37A PLW04
37C PK9
SHAFT
SWITCH MOUNT BRACKET
KEY 5 X 5 X 40
GEARED BEARING HOUSING
HEX BOLT 3⁄8"-16 X 11⁄2
LOCK WASHER 3⁄8
KEY 1⁄4" X 1⁄4" X 11⁄2
BEARING 62032RS
SNAP RING 40
"
SWITCH COVER SCREW
"
"
PHLP HD SCR 10-24 X 3⁄4
FLAT WASHER #10
HEX NUT 10-24
"
038 P6203
039 PR23M
SETSCREW 5⁄16''-18 X 3⁄8''
SPRING
40A P1023040A LOCK NUT 5⁄8"-18
041 P1023041
042 P1023042
043 PSS07
COLLAR
BALL
ARBOR PULLEY
SETSCREW 5⁄16''-18 X 1⁄2''
SETSCREW 1⁄4" - 20 x 1⁄2
KEY 5 X 5 X 45
"
SPECIAL SETSCREW 5⁄16''-18 X 11⁄4''
44A PK02M
BRASS WASHER
POWER CORD
MOTOR CORD
LOGO PLATE
DISCONNECT PWR LABEL
SAFETY GLASSES LABEL
USE GUARD LABEL
READ MANUAL LABEL
ELECTRICITY LABEL
045 P1023045
047 P1023047
048 P1023048
BLADE ARBOR
ARBOR FLANGE
ARBOR NUT
48A P1023048A ARBOR WRENCH
050 P1023050
051 P1023051
052 P1023052
53A PB75
054 P1023054
055 P1023055
MOTOR FRAME SUPPORT
CLIP
PIVOT PIN
HEX BOLT 1⁄2"-13 X 4"
V-BELTS, SET OF 3
MOTOR PULLEY
106A P1023S106A WARNING ID LABEL G1023S
106A P1023S110106A WARNING ID LABEL G1023S110
-49-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
A
A
A
A
A
A
REF# PART#
DESCRIPTION
REF# PART#
DESCRIPTION
400 P1023400
401 P1023401A KNOB
402A PW07
403 P1023403
404 P1023404A MITER BAR
405A P1023405A RING
406A PFH26
407A PN07
408A PSS32
409A PSS29
410 P1023410
411 P1023411
412 P1023412
COMPLETE MITER GAUGE
504 P1022162 SUPPORTING ARM
505 P1022173 PIVOT PIN
506 P1022175 RETAINER
507 P1022163 RETAINER
508 P1022176 SPRING
509 P1022167 SPACER
510 P1022073 SPLITTER
511 P1022164 PAWL
FLAT WASHER 5⁄16"
MITER GAUGE BODY
FLAT HD SCR 10-24 X 1⁄4
"
HEX NUT 10-24
SETSCREW 10-24 X 3⁄4
SETSCREW 10-24 X 1⁄4
STOP
"
"
512 PRP20M
ROLL PIN 4 X 22
513 P1022166 PIN
535 P1023535 U-CLAMP
536 P1023536 L-BRACKET
537 P1023537 LOCKING PLATE
POINTER
SCALE
413 P1023SL413 SETSCREW 10-24 X 5⁄8
414 P1023SL414 ROLL PIN 1.5 X 13
415 P1023SL415 MITER HINGE PIN
501 P1022174
502 P1022171
503 PLN03M
"
538 PB26
539 PW06
540 PN05
541 PB07
542 PW07
543 PN02
HEX BOLT 1⁄4"-20 X 11⁄2
"
FLAT WASHER 1⁄4
"
1
HEX NUT ⁄4"-20
HEX BOLT 5⁄16"-18 X 3⁄4
FLAT WASHER 5⁄16"
HEX NUT 5⁄16"-18
"
GUARD
HEX BOLT M6-1.0 X 40
LOCK NUT M6-1.0
-50-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1.
2.
Low voltage.
Open circuit in motor or loose con- 2.
nections.
1. Check power line for proper voltage.
Motor will not start.
Inspect all lead connections on motor for loose or open con-
nections.
1.
2.
Short circuit in line cord or plug.
Short circuit in motor or loose con- 2.
nections.
1.
Inspect cord or plug for damaged insulation and shorted wires.
Inspect all connections on motor for loose or shorted terminals
or worn insulation.
Motor will not start; fuses or
circuit breakers blow.
3.
Incorrect fuses or circuit breakers in 3.
power line.
Install correct fuses or circuit breakers.
1.
2.
Motor overloaded.
Air circulation through the motor 2.
restricted.
1.
Reduce load on motor.
Clean out motor to provide normal air circulation.
Motor overheats.
1.
Short circuit in motor or loose con- 1.
nections.
Inspect connections on motor for loose or shorted terminals or
worn insulation.
Correct the low voltage conditions.
Install correct fuses or circuit breakers.
Motor stalls (resulting in
blown fuses or tripped cir-
cuit).
2.
3.
Low voltage.
2
Incorrect fuses or circuit breakers in 3.
power line.
4.
1.
2.
1.
Motor overloaded.
4.
Reduce load on motor.
Applying too much pressure to work- 1.
piece.
Belts loose.
Feed workpiece slower.
Machine slows when oper-
ating.
2.
Tighten belts.
Loud, repetitious noise com-
ing from machine.
Pulley setscrews or keys are missing 1.
or loose.
Inspect keys and setscrews. Replace or tighten if necessary.
2.
3.
Motor fan is hitting the cover.
V-belts are defective.
2.
3.
Tighten fan or shim cover.
Replace V-belts. See Maintenance.
Blade is not square w/miter
slot or fence is not square to
blade.
1.
2.
3.
Blade is warped.
Table top is not parallel to blade.
Fence is not parallel to blade.
1.
2.
3.
Replace blade.
Make table parallel to blade. See Adjustments.
Make fence parallel to blade. See Adjustments.
Fence hits table top when
sliding on to the table.
1.
2.
Front rail is bolted too low on table. 1.
Rear rail is bolted too low on the 2.
table.
Raise front rail.
Raise rear rail.
Blade does not reach 90°.
Blade hits insert at 45°.
1.
2.
90° stop bolt is out of adjustment.
Pointer bracket is hitting before the 2.
blade reaches 90°.
1.
Adjust 90° stop bolt. See Adjustments.
File down the right side of the pointer bracket until the blade
can reach 90°.
1.
2.
3.
Hole in insert is inadequate.
Table out of alignment.
Blade position is incorrect.
1.
2.
3.
File or mill the hole in the insert.
Align table. See Adjustments.
Adjust blade position. See Adjustments.
Blade won’t go beneath
table surface.
Table top too low.
Raise table top w/washers.
1.
2.
3.
Hand wheel key is inserted too far.
Bullets are wedged.
Roll pin or setscrew in worm gear is 3.
contacting geared trunnion.
1.
2.
Remove hand wheel and adjust key.
Remove hand wheel and adjust bullets.
Inspect roll pins and setscrews in the worm gear. Tighten if
necessary.
Hand wheels won’t turn.
G1023S Series Heavy-Duty 10'' Table Saw
-51-
Download from Www.Somanuals.com. All Manuals Search And Download.
-52-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
G1023S Series Heavy-Duty 10'' Table Saw
-53-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe-
cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the car-
ton. We will not accept any item back without this number. Proof of purchase must accompany the mer-
chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-54-
G1023S Series Heavy-Duty 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name ____________________________________________________________________________________
Street ____________________________________________________________________________________
City ______________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_______________________FAX________________________
MODEL # G1023S Series 10" Table Saw
Order #___________________________________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
1.
How did you learn about us?
9.
How many of your woodworking machines are Grizzly? _____________
Which benchtop tools do you own? Check all that apply.
___Advertisement
___Catalog
___Friend
___Card Deck
___World Wide Web
10.
___Other__________________________________________________
Which of the following magazines do you subscribe to.
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
2.
___American Woodworker
___Cabinetmaker
___Practical Homeowner
___Shop Notes
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
___Today’s Homeowner
___WOOD
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Woodworker
___Woodworker’s Journal
___Workbench
___Other__________________________________________________
How many of the machines checked above are Grizzly? ____________
11.
12.
Which portable/hand held power tools do you own? Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
3.
___Miter Saw
___Backyard America
___Home Time
___The American Woodworker
___The New Yankee Workshop
___This Old House
___Woodwright’s Shop
___Other__________________________________________________
What machines/supplies would you like Grizzly Industrial to carry?
13.
___Other__________________________________________________
What is your annual household income?
__________________________________________________________
__________________________________________________________
What new accessories would you like Grizzly Industrial to carry?
__________________________________________________________
__________________________________________________________
What other companies do you purchase your tools and supplies from?
__________________________________________________________
__________________________________________________________
Do you think your purchase represents good value?
4.
5.
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
14.
15.
What is your age group?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
6.
7.
8.
How long have you been a woodworker?
16.
17.
18.
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Yes
Would you recommend Grizzly Industrial to a friend?
___Yes ___No
___No
How would you rank your woodworking skills?
___Simple
___Intermediate
___Advanced
___Master Craftsman
Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.
What stationary woodworking tools do you own? Check all that apply.
___Yes
___No
___Air Compressor
___Band Saw
___Drill Press
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Panel Saw
___Planer
19.
Comments:_________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
___Power Feeder
___Radial Arm Saw
___Shaper
___Spindle Sander
___Table Saw
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
___Other__________________________________________________
G1023S Series Heavy-Duty 10'' Table Saw
-55-
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
Visit Our Website Today And Discover Why
Grizzly® Is The Industry Leader!
• SECURE ORDERING
• ORDERS SHIPPED WITHIN 24 HOURS
• E-MAIL RESPONSE WITHIN ONE HOUR
-OR-
Call Today For A
FREE
Full Color Catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Table Top Game NXT011 User Manual
Grizzly Trimmer T20797 User Manual
Harbor Freight Tools Fishing Equipment 95493 User Manual
Harbor Freight Tools Garage Door Opener 69039 User Manual
Harbor Freight Tools Nail Gun 98917 User Manual
Hasbro Games 59233 User Manual
Hearth and Home Technologies Stove 8040 04 28 04 User Manual
Honeywell Thermostat CT50 User Manual
Hotpoint Cooktop DSC60G User Manual
HTC Cell Phone PC36100 User Manual