Grizzly Nail Gun T10726 User Manual

MODEL T10726  
12" VISE-MOUNT  
PAN & BOX BRAKE  
OWNER'S MANUAL  
(For models manufactured since 12/12)  
Copyright © JANUAry, 2013 By grizzly iNdUstriAl, iNC.  
WARNINg: NO PORTION Of ThIS MANUAL MAy BE REPRODUcED IN ANy ShAPE  
OR fORM WIThOUT ThE WRITTEN APPROVAL Of gRIzzLy INDUSTRIAL, INc.  
#ts15553 priNted iN ChiNA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of contents  
INTRODUcTION............................................................................................................................... 2  
Machine description................................................................................................................... 2  
Contact info................................................................................................................................ 2  
Manual Accuracy........................................................................................................................ 2  
identification ............................................................................................................................... 3  
specifications ............................................................................................................................. 3  
SEcTION 1: SAfETy....................................................................................................................... 4  
safety instructions for Machinery............................................................................................... 4  
Additional safety for Brakes....................................................................................................... 6  
SEcTION 2: SETUP......................................................................................................................... 7  
Unpacking .................................................................................................................................. 7  
Needed for setup....................................................................................................................... 7  
inventory..................................................................................................................................... 7  
Cleanup...................................................................................................................................... 8  
site Considerations .................................................................................................................... 8  
Workbench load .................................................................................................................................8  
placement location.............................................................................................................................8  
Workbench Mounting ................................................................................................................. 9  
Assembly.................................................................................................................................... 9  
SEcTION 3: OPERATIONS ........................................................................................................... 10  
Basic Bending .......................................................................................................................... 10  
removing/spacing Fingers ...................................................................................................... 11  
SEcTION 4: AccESSORIES......................................................................................................... 12  
SEcTION 5: MAINTENANcE......................................................................................................... 14  
SEcTION 6: SERVIcE ................................................................................................................... 15  
troubleshooting........................................................................................................................ 15  
Finger Alignment ...................................................................................................................... 16  
SEcTION 7: PARTS....................................................................................................................... 17  
Main.......................................................................................................................................... 17  
labels....................................................................................................................................... 18  
WARRANTy & RETURNS ............................................................................................................. 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUcTION  
Machine Description  
Manual Accuracy  
We are proud to provide a high-quality owners  
manual with your new machine!  
this 12" Vise-Mounted pan & Box Brake is  
designed for small bending projects (such as  
boxes, pans, and trays) in sheet metal that is 22  
gauge or thinner.  
We made every effort to be exact with the instruc-  
tions, specifications, drawings, and photographs  
contained inside. sometimes we make mistakes,  
but our policy of continuous improvement also  
means that sometimes the machine you receive  
will be slightly different than what is shown in  
the manual.  
When secured in a sturdy bench-mounted vise,  
four fingers of different lengths can be arranged  
in a variety of combinations to make 90° bends  
of varying widths up to 12" wide. the adjustable  
fingers also permit the sides of a box to be bent  
without interfering with previously bent sides.  
if you find this to be the case, and the difference  
between the manual and machine leaves you  
confused about a procedure, check our website  
for an updated version. We post current manuals  
and manual updates for free on our website at  
www.grizzly.com.  
contact Info  
We stand behind our machines. If you have  
any questions or need help, use the information  
below to contact us. Before contacting, please get  
the serial number and manufacture date of your  
machine. This will help us help you faster.  
Alternatively, you can call our technical support  
for help. Before calling, please write down the  
Manufacture Date and Serial Number stamped  
into the machine id label (see below). this infor-  
mation helps us determine if updated documenta-  
tion is available for your machine.  
Grizzly Technical Support  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
We want your feedback on this manual. What did  
you like about it? Where could it be improved?  
Please take a few minutes to give us feedback.  
Manufacture date  
serial Number  
Grizzly Documentation Manager  
P.O. Box 2069  
Bellingham, WA 98227-2069  
To reduce your risk of  
serious injury, read this  
entire manual BEfORE  
using machine.  
-2-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Identification  
Finger  
point  
operating  
lever  
Finger Clamp  
sleeve  
eccentric  
shaft  
Finger  
receiver  
Finger  
Cap screw  
Finger  
Clamp  
Fingers  
Vise lug  
Specifications  
Maximum Bending Width ............................... 12"  
Maximum Bending Capacity ... 22 ga. Mild steel  
Bending Angle range .............................. 0°–90°  
Number of Fingers............................................. 4  
Finger sizes............................... 1", 2", 3", and 6"  
Weight .......................................................22 lbs.  
-3-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEcTION 1: SAfETy  
for your Own Safety, Read Instruction  
Manual Before Operating This Machine  
The purpose of safety symbols is to attract your attention to possible hazardous conditions.  
This manual uses a series of symbols and signal words intended to convey the level of impor-  
tance of the safety messages. The progression of symbols is described below. Remember that  
safety messages by themselves do not eliminate danger and are not a substitute for proper  
accident prevention measures. Always use common sense and good judgment.  
Indicates an imminently hazardous situation which, if not avoided,  
WILL result in death or serious injury.  
Indicates a potentially hazardous situation which, if not avoided,  
cOULD result in death or serious injury.  
Indicates a potentially hazardous situation which, if not avoided,  
MAy result in minor or moderate injury. It may also be used to alert  
against unsafe practices.  
This symbol is used to alert the user to useful information about  
proper operation of the machine.  
NOTICE  
Safety Instructions for Machinery  
OWNER’S MANUAL. read and understand this ELEcTRIcAL EQUIPMENT INJURy RISKS. you  
owners manual BeFore using machine.  
can be shocked, burned, or killed by touching live  
electrical components or improperly grounded  
machinery. to reduce this risk, only allow qualified  
service personnel to do electrical installation or  
repair work, and always disconnect power before  
accessing or exposing electrical equipment.  
TRAINED OPERATORS ONLy. Untrained oper-  
ators have a higher risk of being hurt or killed.  
only allow trained/supervised people to use this  
machine. When machine is not being used, dis-  
connect power, remove switch keys, or lock-out  
machine to prevent unauthorized useespecially  
around children. Make workshop kid proof!  
DIScONNEcT POWER fIRST. Always discon-  
nect machine from power supply BeFore making  
adjustments, changing tooling, or servicing machine.  
this prevents an injury risk from unintended startup  
or contact with live electrical components.  
DANgEROUS ENVIRONMENTS. do not use  
machinery in areas that are wet, cluttered, or have  
poor lighting. operating machinery in these areas  
greatly increases the risk of accidents and injury.  
EyE PROTEcTION. Always wear ANsi-approved  
safety glasses or a face shield when operating or  
observing machinery to reduce the risk of eye  
injury or blindness from flying particles. everyday  
eyeglasses are not approved safety glasses.  
MENTAL ALERTNESS REQUIRED. Full mental  
alertness is required for safe operation of machin-  
ery. Never operate under the influence of drugs or  
alcohol, when tired, or when distracted.  
-4-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WEARINg PROPER APPAREL. do not wear fORcINg MAchINERy. do not force machine.  
clothing, apparel or jewelry that can become  
entangled in moving parts. Always tie back or  
cover long hair. Wear non-slip footwear to avoid  
accidental slips, which could cause loss of work-  
piece control.  
it will do the job safer and better at the rate for  
which it was designed.  
NEVER STAND ON MAchINE. serious injury  
may occur if machine is tipped or if the cutting  
tool is unintentionally contacted.  
hAzARDOUS DUST. dust created while using  
machinery may cause cancer, birth defects, or  
long-term respiratory damage. Be aware of dust  
hazards associated with each workpiece material,  
and always wear a Niosh-approved respirator to  
reduce your risk.  
STABLE MAchINE. Unexpected movement dur-  
ing operation greatly increases risk of injury or  
loss of control. Before starting, verify machine is  
stable and mobile base (if used) is locked.  
USE REcOMMENDED AccESSORIES. Consult  
this owners manual or the manufacturer for rec-  
ommended accessories. Using improper acces-  
sories will increase the risk of serious injury.  
hEARINg PROTEcTION. Always wear hear-  
ing protection when operating or observing loud  
machinery. extended exposure to this noise  
without hearing protection can cause permanent  
hearing loss.  
UNATTENDED OPERATION. to reduce the  
risk of accidental injury, turn machine OFF and  
ensure all moving parts completely stop before  
walking away. Never leave machine running  
while unattended.  
REMOVE ADJUSTINg TOOLS. tools left on  
machinery can become dangerous projectiles  
upon startup. Never leave chuck keys, wrenches,  
or any other tools on machine. Always verify  
removal before starting!  
MAINTAIN WITh cARE. Follow all maintenance  
instructions and lubrication schedules to keep  
machine in good working condition. A machine  
that is improperly maintained could malfunction,  
leading to serious personal injury or death.  
INTENDED USAgE. only use machine for its  
intended purpose and never make modifications  
not approved by grizzly. Modifying machine or  
using it differently than intended may result in  
malfunction or mechanical failure that can lead to  
serious personal injury or death!  
chEcK DAMAgED PARTS. regularly inspect  
machine for any condition that may affect safe  
operation. immediately repair or replace damaged  
or mis-adjusted parts before operating machine.  
AWKWARD POSITIONS. Keep proper footing  
and balance at all times when operating machine.  
do not overreach! Avoid awkward hand positions  
that make workpiece control difficult or increase  
the risk of accidental injury.  
MAINTAIN POWER cORDS. When disconnect-  
ing cord-connected machines from power, grab  
and pull the plug—Not the cord. pulling the cord  
may damage the wires inside. do not handle  
cord/plug with wet hands. Avoid cord damage by  
keeping it away from heated surfaces, high traffic  
areas, harsh chemicals, and wet/damp locations.  
chILDREN & BySTANDERS. Keep children and  
bystanders at a safe distance from the work area.  
stop using machine if they become a distraction.  
gUARDS & cOVERS. guards and covers reduce  
accidental contact with moving parts or flying  
debris. Make sure they are properly installed,  
undamaged, and working correctly.  
EXPERIENcINg DIffIcULTIES. if at any time  
you experience difficulties performing the intend-  
ed operation, stop using the machine! Contact our  
technical support at (570) 546-9663.  
-5-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional Safety for Brakes  
cRUShINg & AMPUTATION INJURIES. the PINchINg. to prevent pinching injuries, lower the  
brake can quickly crush or amputate fingers or fingers when not in use.  
hands. Never place fingers or hands underneath  
fingers.  
gLOVES AND gLASSES. Always wear leather  
gloves and approved safety glasses when using  
SEcURINg Brake. Before using, secure brake to this brake.  
a sturdy vise that is securely fastened to a work-  
bench that can support the weight and dynamic hEATINg METAL. heating the workpiece with a  
forces involved in bending sheet metal. otherwise, torch while it is in the brake will weaken the metal  
the brake may unexpectedly move or fall, causing of the fingers and frame. do not use a torch or  
serious injury or property damage.  
other similar heating tool near the brake.  
METAL EDgES. sharp edges on sheet metal can BAcK INJURIES. the operating lever motion  
result in severe cuts. Always wear leather gloves required to operate this brake is potentially harm-  
and chamfer/de-burr sharp sheet metal edges ful if proper technique is not used. to avoid back  
before handling.  
injuries, keep your back vertical and never over-  
exert yourself.  
TOOLS IN POOR cONDITION. Using this tool  
with loose hardware or damaged components OVERLOADINg. overloading this machine can  
could result in sudden, uncontrolled movements cause injury from flying parts if breakage occurs .  
during use. inspect the brake for cracked compo- do not exceed the machine capacities.  
nents, damaged linkage, levers, or loose fasten-  
ers. Correct any problems before use.  
Like all machinery there is potential danger  
when operating this machine. Accidents  
are frequently caused by lack of familiarity  
or failure to pay attention. Use this machine  
with respect and caution to decrease the  
risk of operator injury. If normal safety pre-  
cautions are overlooked or ignored, seri-  
ous personal injury may occur.  
No list of safety guidelines can be com-  
plete. Every shop environment is different.  
Always consider safety first, as it applies  
to your individual working conditions. Use  
this and other machinery with caution and  
respect. failure to do so could result in  
serious personal injury, damage to equip-  
ment, or poor work results.  
-6-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEcTION 2: SETUP  
Unpacking  
Inventory  
Your machine was carefully packaged for safe  
transportation. Remove the packaging materials  
from around your machine and inspect it. If you  
discover any damage, please call us immediately  
at (570) 546-9663 for advice.  
The following is a description of the main compo-  
nents shipped with your machine. Lay the compo-  
nents out to inventory them.  
If any non-proprietary parts are missing (e.g. a  
nut or a washer), we will gladly replace them; or  
for the sake of expediency, replacements can be  
obtained at your local hardware store.  
Save the containers and all packing materials for  
possible inspection by the carrier or its agent.  
Otherwise, filing a freight claim can be difficult.  
Shipping Inventory: (figure 1)  
Qty  
When you are completely satisfied with the condi-  
tion of your shipment, inventory the contents.  
A. Brake Assembly ......................................... 1  
B. operating lever w/set screw M5-.8 x 8...... 1  
c. lever shaft ................................................. 1  
SUFFOCATION HAZARD!  
Keep children and pets away  
from plastic bags or packing  
materials shipped with this  
machine. Discard immediately.  
A
B
Needed for Setup  
C
the following are needed to complete the setup  
process, but are not included with your machine.  
figure 1. shipping inventory.  
Description  
Qty  
Cleaner/degreaser (Page 8) ...... As Needed  
disposable shop rags............... As Needed  
sturdy Workbench...................................... 1  
Vise secured to Workbench....................... 1  
Wrench 17mm ............................................ 1  
hex Wrench 2.5mm.................................... 1  
hex Wrench 6mm....................................... 1  
NOTICE  
If you cannot find an item on this list, care-  
fully check the machine and the packaging  
materials. Some of these items may be pre-  
installed for shipping or become misplaced  
during unpacking.  
-7-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
cleanup  
Site considerations  
the unpainted surfaces of your machine are  
coated with a heavy-duty rust preventative that  
prevents corrosion during shipment and storage.  
this rust preventative works extremely well, but it  
will take a little time clean.  
Workbench Load  
refer to Specifications on Page 3 for the  
weight of your machine. some workbenches may  
require additional reinforcement to support both  
the machine and materials.  
Always follow the manufacturers instructions with  
any cleaning product you use and make sure you  
work in a well-ventilated area to minimize expo-  
sure to toxic fumes.  
Placement Location  
Consider existing and anticipated needs, size of  
material to be processed through each machine,  
and space for auxiliary stands, work tables or  
other machinery when establishing a location for  
your new machine. see figure 2 for the minimum  
working clearances.  
Before cleaning, gather the following:  
disposable rags  
Cleaner/degreaser (Wd•40 works well)  
safety glasses & disposable gloves  
plastic paint scraper (optional)  
hex Wrench 6mm  
Quality metal protectants products like g96®  
gun treatment, slipit®, or Boeshield® t-9  
(see Page 13 for offering from grizzly).  
Vise  
Basic steps for removing rust preventative:  
1. put on safety glasses.  
2. remove the fingers (refer to Page 11 for  
detailed instructions).  
3314  
3. Coat the rust preventative with a liberal  
amount of cleaner/degreaser, then let it soak  
for 5–10 minutes.  
Brake  
4. Wipe off the surfaces. if your cleaner/  
degreaser is effective, the rust preventative  
will wipe off easily. if you have a plastic paint  
scraper, scrape off as much as you can first,  
then wipe off the rest with the rag.  
5. repeat Steps 3–4 as necessary until clean.  
1312  
6. Apply a thin coat of quality metal protectant  
to the fingers and other unpainted metal sur-  
faces, then re-install the fingers.  
figure 2. Minimum working clearances.  
Avoid chlorine-based solvents, such as  
acetone or brake parts cleaner, that may  
damage painted surfaces.  
-8-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Vise & Workbench  
Setup  
except for the operating lever, the Model t10726  
has been assembled and adjusted at the factory.  
the forces exerted on the brake during operation  
are substantial. the brake must be firmly secured  
in a vise (see figure 5) that is solidly attached  
to a workbench that will support the weight and  
dynamic pressures of the operation (refer to Page  
12 for workbench and vise options from grizzly).  
To attach the operating lever:  
1. thread the operating lever shaft (see figure  
3) into the eccentric shaft, and tighten it with  
the wrench.  
Mount the brake by tightening the vise jaws  
against the lug at the bottom of the brake.  
Note: Use pieces of cardboard, wood, or padded  
jaw faces between the vise jaws and the vise lug  
to prevent surface damage to the brake.  
operating  
lever shaft  
eccentric  
shaft  
figure 3. operating lever shaft installed.  
2. slide the operating lever onto the lever shaft  
(see figure 4), and secure it with the pre-  
installed set screw.  
Vise  
lug  
figure 5. example of Model t10726 secured in  
vise mounted to a workbench.  
set screw  
Make sure the workbench that the brake will  
be mounted on is stable and can support  
the weight of the tool, the workpiece, and  
the forces exerted during operation.  
operating  
lever  
figure 4. operating lever attached.  
-9-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEcTION 3: OPERATIONS  
Basic Bending  
Damage to your eyes or hands could result  
from using this brake without proper protec-  
tive gear. Always wear safety glasses and  
leather gloves when operating this brake.  
the Model t10726 bends mild steel up to 22  
gauge at angles up to 90°.  
To perform a basic bending operation:  
1. Clean away any debris from the workpiece.  
2. Use a pencil or scribe to mark the bending  
location.  
3. lift the operating lever and center the  
workpiece under the fingers and directly over  
the mark you made in Step 2 (see figure 6).  
If you are not experienced with this type  
of machine, WE STRONgLy REcOMMEND  
that you seek additional training outside of  
this manual. Read books/magazines or get  
formal training before beginning any proj-  
ects. Regardless of the content in this sec-  
tion, grizzly Industrial will not be held liable  
for accidents caused by lack of training.  
figure 6. Workpiece positioned under fingers.  
Keep your fingers and  
hands away from the fin-  
gers during operation to  
avoid the risk of crushing  
injuries.  
-10-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. slowly lower the operating lever until the  
bend in the workpiece reaches the desired  
angle (see figure 7 for an example).  
2. From the rear of the brake, carefully push the  
fingers forward, as shown in figure 8, then  
slowly lower the lever behind the brake. the  
fingers should clear the front of the frame as  
they are lowered.  
Note: Make sure the finger points are directly  
over the finger receiver groove as you lower  
the lever.  
Finger Cap  
screw  
Fingers Forward  
of Frame  
figure 8. Fingers positioned forward of frame.  
3. remove the cap screw(s) that secure the  
finger, then pull the fingers from the clamps.  
figure 7. example of a 90° bend.  
Note: It may be necessary to loosen the first  
cap screw on the finger(s) adjacent to the one  
you are removing to release the clamping  
pressure.  
5. lift the operating lever to raise the fingers,  
remove the bent workpiece, then lower the  
fingers back into the finger receiver.  
4. position the fingers in an arrangement for  
the length or width of the desired bend (see  
figure 9 for an example).  
If a pan or box is desired, refer to the next  
subsection to position the fingers for this  
operation.  
Note: As you move or replace fingers, make  
sure they are aligned with each other (see  
Finger Alignment on Page 16 for detailed  
instructions).  
Removing/Spacing  
fingers  
Finger Clamp  
the fingers can be spaced for pan and box opera-  
tions. this involves removing one or more fingers  
so that the others can be properly spaced.  
Tool Needed  
Qty  
hex Wrench 6mm.............................................. 1  
figure 9. example of finger spacing.  
To remove and space fingers:  
5. raise the fingers up, then lower them back  
into the finger receiver.  
1. lift the operating lever to raise the fingers.  
-11-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCessories  
SEcTION 4: AccESSORIES  
g5618—Deburring Tool with two Blades  
the quickest tool for smoothing freshly sheared  
metal edges. Comes with two blades, one for  
steel and aluminum and one for brass and cast  
iron.  
Installing unapproved accessories may  
cause machine to malfunction, resulting in  
serious personal injury or machine damage.  
To reduce this risk, only install accessories  
recommended for this machine by grizzly.  
NOTICE  
Refer to our website or latest catalog for  
additional recommended accessories.  
figure 11. Model g5618 deburring tool.  
heavy-Duty Bench Vises with Anvils  
g7059—5", 45 lbs.  
g7060—6", 68 lbs.  
these tough vises are ideal for all bench work  
applications. large machined center slide keeps  
jaws aligned under maximum pressure. other  
features include large Acme screws, anvil faces,  
and 0°–90° swivel.  
Super heavy-Duty Birch Workbench  
h8361—60" x 30"  
h8362—72" x 36"  
sized to fit the needs of any shop, these super  
heavy-duty Birch Workbenches have solid 3"  
thick tops that stand 38" above the floor. the end  
vise measures 1434" wide (h8361) or 1734" wide  
(h8362) and has a 7" maximum capacity. stable  
laminated birch provides strength and durability.  
you'll be proud to have this workbench in your  
shop!  
figure 10. heavy-duty Bench Vise with Anvil.  
figure 12. super heavy-duty Birch Workbench.  
order online at www.grizzly.com or call 1-800-523-4777  
-12-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bostitch compound Action Aviations Snips  
T22298—Straight  
T22299—Left  
Basic Eye Protection  
T20501—face Shield crown Protector 4"  
T20502—face Shield crown Protector 7"  
T20503—face Shield Window  
T20452—"Kirova" Anti-Reflective S. glasses  
T20451—"Kirova" clear Safety glasses  
h0736—Shop fox® Safety glasses  
h7194—Bifocal Safety glasses 1.5  
h7195—Bifocal Safety glasses 2.0  
h7196—Bifocal Safety glasses 2.5  
T22300—Right  
these 10" Aviation snips are designed for cut-  
ting heavy stock in a straight, left, or right cut-  
ting direction. developed with tiN-coated cutting  
blades to reduce wear and extend blade life, they  
cut up to 18 gauge cold-rolled steel or 23 gauge  
stainless steel. the patented flush-mounted side  
hardware also helps prevent metal from catching  
while cutting. these snips meet or exceed ANsi  
standards.  
T20502  
T20452  
t22298  
T20503  
T20451  
h0736  
t22299  
h7194  
figure 13. Assortment of basic eye protection.  
t22300  
Recommended Metal Protectants  
g5562—SLIPIT® 1 Qt. gel  
g5563—SLIPIT® 12 oz Spray  
g2871—Boeshield® T-9 12 oz Spray  
g2870—Boeshield® T-9 4 oz Spray  
h3788—g96® gun Treatment 12 oz Spray  
h3789—g96® gun Treatment 4.5 oz Spray  
figure 15. Bostitch Compound Aviation snips.  
figure 14. recommended products for protect-  
ing unpainted cast iron/steel part on machinery.  
order online at www.grizzly.com or call 1-800-523-4777  
-13-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEcTION 5: MAINTENANcE  
regular maintenance on the Model t10726 will  
ensure its optimum performance. Make a habit of  
inspecting your brake each time you use it.  
finger clamp Sleeve Lubrication. to  
reduce wear, periodically apply a couple of  
drops of light machine oil to each end of the  
finger clamp sleeves (see figure 17), then  
slide the sleeves side-to-side several times to  
distribute the oil. Wipe away any excess oil.  
There are three main areas to maintain on the  
Model T10726:  
fingers and finger Receiver. After han-  
dling the fingers for removal, spacing, or  
re-installation, always apply a quality metal  
protectant to the fingers and finger receiver  
(see Page 13 for offerings from grizzly) to  
prevent corrosion.  
Apply oil here  
When storing the brake for long periods of  
time, make a habit of occasionally re-apply-  
ing the metal protectant as directed above.  
Eccentric Shaft Rod. periodically or if the  
up-and-down finger movement becomes stiff,  
apply a couple of drops of light machine oil to  
the eccentric shaft rods on each end of the  
eccentric shaft (see figure 16). the rods are  
accessible between the eccentric shaft and  
the roller brackets. rotate the lever front-to-  
back several times to distribute the oil, then  
wipe away any excess.  
figure 17. Finger clamp lubrication points.  
eccentric  
shaft rod  
eccentric  
shaft  
roller  
Bracket  
figure 16. eccentric shaft rod between the  
eccentric shaft and the frame.  
-14-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEcTION 6: SERVIcE  
Review the troubleshooting and procedures in this section if a problem develops with your machine. If you  
need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.  
Note: Please gather the serial number and manufacture date of your machine before calling.  
Troubleshooting  
Symptom  
Possible cause  
Possible Solution  
heavy resistance  
during bends.  
1. Machine capacities are exceeded.  
1. Use sheet metal that does not exceed 22 gauge  
mild steel.  
2. Fingers not aligned with finger receiver  
groove.  
2. Make sure fingers are aligned with finger receiver  
groove as fingers are lowered for bend.  
Bend radius is not  
consistent across  
workpiece.  
1. Machine capacities are exceeded.  
1. Use sheet metal that does not exceed 22 gauge  
mild steel.  
2. Bottom of fingers not aligned with each  
other.  
2. Make sure fingers are rmly seated in finger clamps  
and the finger points are aligned with each other.  
point of fingers are  
chipping or rolling.  
1. Fingers not aligned with finger receiver  
groove.  
1. Make sure fingers are aligned with finger receiver  
groove as fingers are lowered for bend. replace  
fingers if damaged.  
2. Machine capacities are exceeded.  
2. Use sheet metal that does not exceed 22 gauge  
mild steel. replace fingers if damaged.  
Workpiece shows  
scoring marks or  
scratches after  
bend.  
1. debris on fingers or finger receiver.  
1. Clean fingers and finger receiver (Page 14).  
2. polish out scratches, and apply tape on the  
workpiece at the bend locations for protection.  
2. Fingers or finger receiver has scratches.  
-15-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
look along the length of the fingers from the side  
to identify any finger point that is not aligned with  
the rest.  
finger Alignment  
to produce straight bends, the finger points (see  
figure 18) must all be aligned evenly.  
Tool Needed  
hex Wrench 6mm.............................................. 1  
Qty  
When moving or re-installing the fingers, there is  
play in the vertical positioning which can be used  
to align the fingers.  
To align the finger points:  
1. loosen, but do not remove, the cap screws  
that secures the finger.  
Finger  
Cap screws  
Note: It may be necessary to also loosen  
the cap screws on each side of the finger to  
relieve the pressure from the finger clamp.  
2. Apply upward pressure to the finger to firmly  
seat it into the finger clamp.  
3. observe the alignment of the finger points  
from the side again. if necessary, repeat this  
procedure to bring all fingers into alignment.  
Finger  
Clamp  
Finger points  
figure 18. Finger points and cap screws.  
-16-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEcTION 7: PARTS  
Main  
20  
19  
12  
9
21  
22  
11  
13  
14  
10  
15  
16  
17  
5
2
1
3
8
4
7
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
PT10726001  
VISE LUG  
FRAME  
12  
13  
14  
15  
16  
17  
19  
20  
21  
22  
PT10726012  
SLEEVE STOP PLATE  
STOP PLATE RIVET  
BENDING LEVER SHAFT  
FINGER CLAMP  
2
PT10726002  
PT10726003  
PT10726004  
PT10726005  
PT10726007  
PT10726008  
PT10726009  
PT10726010  
PT10726011  
PT10726013  
PT10726014  
PT10726015  
PCAP31M  
PLW04M  
3
BENDING FINGER 75MM  
BENDING FINGER 50MM  
STOP ROD 6 X 30MM  
4
5
CAP SCREW M8-1.25 X 25  
LOCK WASHER 8MM  
BENDING LEVER  
7
BENDING FINGER 25MM  
BENDING FINGER 150MM  
ECCENTRIC SHAFT  
8
PT10726019  
PT10726020  
PSS31M  
9
LEVER HANDLE  
10  
11  
ECCENTRIC SHAFT ROD  
FINGER CLAMP SLEEVE  
SET SCREW M5-.8 X 8  
SET SCREW M5-.8 X 12  
PSS53M  
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here  
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.  
-17-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Labels  
31  
32  
33  
34  
35  
REF PART #  
REF PART #  
DESCRIPTION  
DESCRIPTION  
31  
32  
33  
PT10726031  
ID LABEL  
34  
35  
PT10726034  
PPAINT-01  
EYE INJURY HAZARD LABEL  
PT10726032  
PT10726033  
HAZARD STRIP LABEL  
PINCH HAZARD LABEL  
GRIZZLY GREEN TOUCH-UP PAINT  
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes  
off or becomes unreadable, the owner of this machine MUST replace it in the original location  
-18-  
Model T10726 (Mfg. Since 12/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY CARD  
Name_____________________________________________________________________________  
Street_____________________________________________________________________________  
City _______________________ State_________________________ Zip _____________________  
Phone #____________________ Email _________________________________________________  
Model # ____________________ Order #_______________________ Serial #__________________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop  
better products and services. Of course, all information is strictly confidential.  
1. How did you learn about us?  
____ Advertisement  
____ Card Deck  
____ Friend  
____ Website  
____ Catalog  
____ Other:  
2. Which of the following magazines do you subscribe to?  
____ Cabinetmaker & FDM  
____ Family Handyman  
____ Hand Loader  
____ Popular Science  
____ Popular Woodworking  
____ Precision Shooter  
____ Projects in Metal  
____ RC Modeler  
____ Rifle  
____ Shop Notes  
____ Wooden Boat  
____ Woodshop News  
____ Woodsmith  
____ Handy  
____ Woodwork  
____ Home Shop Machinist  
____ Journal of Light Cont.  
____ Live Steam  
____ Woodworker West  
____ Woodworker’s Journal  
____ Other:  
____ Model Airplane News  
____ Old House Journal  
____ Popular Mechanics  
____ Shotgun News  
____ Today’s Homeowner  
____ Wood  
3. What is your annual household income?  
____ $20,000-$29,000  
____ $30,000-$39,000  
____ $40,000-$49,000  
____ $70,000+  
____ $50,000-$59,000  
____ $60,000-$69,000  
4. What is your age group?  
____ 20-29  
____ 30-39  
____ 60-69  
____ 40-49  
____ 70+  
____ 50-59  
5. How long have you been a woodworker/metalworker?  
____ 0-2 Years ____ 2-8 Years  
____ 8-20 Years  
____20+ Years  
____10+  
6. How many of your machines or tools are Grizzly?  
____ 0-2 ____ 3-5  
____ 6-9  
7. Do you think your machine represents a good value?  
8. Would you recommend Grizzly Industrial to a friend?  
_____Yes  
_____Yes  
_____No  
_____No  
9. Would you allow us to use your name as a reference for Grizzly customers in your area?  
Note: We never use names more than 3 times. _____Yes _____No  
10. Comments:_____________________________________________________________________  
_________________________________________________________________________________  
_________________________________________________________________________________  
_________________________________________________________________________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
GRIZZLY INDUSTRIAL, INC.  
P.O. BOX 2069  
BELLINGHAM, WA 98227-2069  
FOLD ALONG DOTTED LINE  
Send a Grizzly Catalog to a friend:  
Name_______________________________  
Street_______________________________  
City______________State______Zip______  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTy & RETURNS  
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from  
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,  
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty  
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-  
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent  
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.  
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and  
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.  
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,  
or consequential damages arising from the use of our products.  
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue  
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We  
will not accept any item back without this number. Proof of purchase must accompany the merchandise.  
The manufacturers reserve the right to change specifications at any time because they constantly strive to  
achieve better quality equipment. We make every effort to ensure that our products meet high quality and  
durability standards and we hope you never need to use this warranty.  
Please feel free to write or call us if you have any questions about the machine or the manual.  
Thank you again for your business and continued support. We hope to serve you again soon.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!  
~Since 1983~  
Visit Our Website Today For  
Current Specials!  
ORDER  
24 HOURS A DAY!  
1-800-523-4777  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Inc Pressure Washer 1535 User Manual
Greenheck Fan Ventilation Hood FSD 331 User Manual
Grizzly Meat Grinder H7778 User Manual
Grundig Stereo System YB500 User Manual
Haier Flat Panel Television 24D2000 User Manual
Hasbro Telephone 88 316 User Manual
Hotpoint Washer WMUD 823 User Manual
HP Hewlett Packard Network Card FCA2214DC PCI X User Manual
Husqvarna Chainsaw FS 513 User Manual
Impex Fitness Equipment 157 User Manual