34˚ FRAMING NAILER KIT
MODEL H5571
INSTRUCTION MANUAL
COPYRIGHT © SEPTEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE
AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS
PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF
THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE. CONTACT CUS-
TOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES.
PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Pneumatic Tools
18. DISCONNECT TOOLS before ser-
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough to
reach your work without stretching.
vicing and changing accessories.
19. USE
THE
RECOMMENDED
Consult the
ACCESSORIES.
owner’s manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
11. WEAR PROPER APPAREL. DO
NOT wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear a protective
hair covering to contain long hair.
20. CHECK
DAMAGED
PARTS.
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate prop-
erly and perform its intended func-
tion. Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask if cut-
ting operation is dusty. Everyday
eyeglasses only have impact resis-
tant lenses, they are NOT safety
glasses.
13. WEAR APPROVED HEARING
PROTECTION.
14. SECURE WORK. Use clamps or a
vise to hold work when practical. It is
safer than using your hand and frees
both hands to operate tool.
21. NEVER LEAVE UNATTENDED
TOOL CONNECTED TO AIR.
Disconnect the air hose and do not
leave tool until it is relieved of any
built up pressure.
15. DO NOT OVERREACH. Keep prop-
er footing and balance at all times.
16. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean for
best and safest performance. Follow
instructions for lubricating and
changing accessories.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL
WHILE UNSUPERVISED.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL. Seek formal
training or research books or maga-
zines that specialize in pneumatic
tools.
17. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. DO NOT carry
tool with hand on trigger and always
disconnect from air when not in use.
-2-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Nailer Safety
In addition to the rules stated in the previ-
ous section, and those in the warning
boxes throughout this manual, please
observe the following safety tips for your
new nailer:
1. READ THIS ENTIRE MANUAL
BEFORE OPERATING THE NAIL-
ER.
2. ALWAYS DISCONNECT AIR FROM
THE NAILER whenever servicing,
carrying, or installing nails. During
maintenance, a nailer connected to
air may fire accidentally, causing seri-
ous personal injury.
3. DO NOT PLACE HANDS NEAR
NAIL POINT OF ENTRY. Nail can
deflect and be driven through the sur-
face of the workpiece, puncturing
your hand or fingers.
Operating this nailer can propel
objects into the air, causing immedi-
ate eye damage. To protect yourself,
always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, this
nailer discharges at 85-90 decibels.
To protect your hearing, always wear
ANSI approved ear protection when
operating this nailer.
4. NEVER CONNECT THE NAILER TO
PRESSURIZED
OXYGEN
OR
OTHER COMBUSTIBLE GASES as
a power source. Only use filtered,
lubricated, and regulated compressed
air.
5. ALWAYS
KEEP
ANY
BYSTANDERS BEHIND NAILER
OR AWAY FROM AREA DURING
USE. Nails may be driven completely
though wood and could become dan-
gerous projectiles.
6. DO NOT CARRY THE NAILER BY
ANY OTHER PART THAN THE
HANDLE, and do not carry the nailer
by the air hose.
7. DO NOT KEEP THE TRIGGER
PULLED ON THE SAFETY YOKE
MECHANISM WHEN CARRYING
OR HOLDING THE TOOL.
Never point this nailer at yourself or
another person! Always pay attention
to the direction this nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warn-
ing may result in serious personal
injury.
8. DO NOT USE A CHECK VALVE OR
ANY OTHER FITTING that allows air
to remain in the tool.
-3-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Commentary
We are proud to offer the Grizzly Model
H5571 34˚ Framing Nailer. This model is
part of a growing Grizzly family of fine
power tools. When used according to the
guidelines set forth in this manual, you can
expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
Most important, we stand behind our tools.
If you have any service questions or parts
requests, please call or write us at the
location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
The Model H5571 features
a
360˚
Fax: (800) 438-5901
adjustable exhaust, a convenient top load-
ing magazine, a safety trigger and a
durable plastic carrying case. The Model
H5571 shoots standard 0.113-0.162 diam-
eter shank D head ("clipped head") nails
2"-31⁄2" in length and accepts up to 50 nails
at a time. At 8 lbs., this model is very light
for its size.
E-Mail: [email protected]
We are pleased to provide this manual
with the Model H5571. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. This manual
represents our effort to produce the best
documentation possible.
Read the manual before assembly
and operation. Become familiar with
this tool, its safety instructions, and
its operation before beginning any
work. Serious personal injury may
result if safety or operational infor-
mation is not understood or followed.
The specifications, details, and pho-
tographs in this manual represent the
Model H5571 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
-4-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Compressed Air System
Safety Yoke Mechanism
The Model H5571 is designed to be oper-
ated at 85-115 psi. DO NOT exceed the
maximum operating pressure!
A safety yoke mechanism (bump fire) on
the nose of the nailer acts as a safety
device. When the trigger is pressed, the
nailer will not fire until the safety yoke
mechanism is depressed.
Before you use your new nailer, regulate
the air pressure on your air compressor to
barely over the minimum psi for your nail-
er. Increase air pressure only if needed.
To check the safety yoke:
1. Make sure the nailer is disconnect-
ed from the air supply!
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger,
depress the safety yoke mechanism
against a scrap piece of wood that is
clean and free of any knots, nails, or
other foreign objects. If the nailer
DOES NOT FIRE, then the safety
yoke mechanism is working correctly.
If the nailer DOES FIRE when you do
this, immediately disconnect the nailer
from the air supply and call our cus-
tomer service for help.
Many pneumatic tools benefit from an in-
line filter/lubricator/regulator unit. Using
this unit protects your tool from damaging
water build-up, allows you to adjust and
maintain constant air pressure to your tool,
and saves you the inconvenience of having
to manually lubricate your tool every time
you use it. Check the current Grizzly cata-
log for availability of this unit. If you plan on
installing a filter/lubricator/regulator unit in
your compressed air system, always follow
the connection instructions that come with
the unit.
Similarly if the nailer fires when the trigger
is pulled, without the safety yoke mech-
anism being depressed, then the nailer is
not working properly.
If either of these two conditions develop
after you have used your nailer for a peri-
od of time, check the lubrication of these
mechanisms.
Exceeding the maximum permissible
operating pressure may cause the
nailer to explode, blowing metal frag-
ments in all directions. To protect
yourself from serious personal injury,
DO NOT allow your air compressor to
exceed the recommended pressure
when connected to this nailer!
The safety yoke is
a
mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the nailer at yourself or any
bystanders. Serious injury may occur.
-5-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Oiling Nailer
Loading Nailer
Special oil has been included with your
new Grizzly nailer to help maintain its use-
ful life. Place one drop of oil in the nailer air
inlet (as shown in Figure 1) before every
use. Wipe off any excess oil near the nail-
er exhaust to avoid dust build-up. When
the oil that was included with the nailer has
been completely used, replace with Grizzly
Model G2820 Pneumatic Tool Oil.
To load your nailer:
1. Disconnect the air supply from the
nailer!
2. Pull the magazine pusher all the way
back until it locks in place.
3. Place a stick of nails into the maga-
zine as shown in Figure 2. Make sure
the pointed ends of the nails are fac-
ing down.
Another option to manual oiling would be
to install a lubricator in your air compressor
line. If your air compressor line already has
a lubricator, then regular lubrication of your
nailer will not be necessary. Just make
sure there is always oil in the lubricator.
As mentioned before, the best option is to
install a filter/lubricator/regulator unit avail-
able in the Grizzly catalog.
Figure 2. Loading the nailer.
3. Slide the stick of nails all the way
down to the nose of the nailer.
4. Pull the magazine pusher all the way
back, release the catch lever, then let
it come forward until it rests against
the nail stick.
When choosing nails for your Model
H5571, follow these guidelines:
Figure 1. Lubricating nailer via air inlet.
Diameter: 0.113" - 0.162"
Length: 2"-31⁄2
"
Capacity: 50 Nails
-6-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Nailer
Adjusting Depth
The nose of the gun houses a depth
adjustment knob for setting the depth that
the nailer drives nails into the workpiece.
If you have not read the safety instruc-
tions in this manual, DO NOT operate
the nailer.
To adjust the depth:
Before you operate your nailer, place one
drop of the included oil into the quick con-
nect fitting where the nailer connects to the
air supply.
1. If the nail is driven too far into the
workpiece, rotate the knob clockwise
as shown in Figure 4)
2. If the nail is not driven far enough into
the workpiece, rotate the knob
counter clockwise.
To operate your nailer:
1. Connect the air supply to the quick
connect fitting.
2. Hold the nailer perpendicular to the
surface of a piece of wood that is thick
enough for the length of nails you
have loaded. Depress the safety yoke
mechanism on your workpiece.
3. Before pressing the trigger, make
sure your free hand is positioned out
of the way of a potential path of a nail
in case of deflection. (Deflection is
caused when the nail changes its
path, resulting in the nail puncturing
the surface of the workpiece as
shown in Figure 3.) Deflection can
cause injury if your free hand is secur-
ing the workpiece in the location that
the nail deflects and damage your
workpiece.
Deeper
Shallower
Figure 4. Depth adjustment knob located
on nailer nose guide.
Figure 3. Example of nail deflection.
4. Pull the trigger. If the nail drove into
the wood far enough, continue with
your intended operations. If the nail
either went too far or not far enough,
adjust the depth.
-7-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Single/Bump Fire Mode
Clearing Jammed Nails
The Model H5571 is equipped with a sin-
gle/bump fire trigger.
The most frequent situation with any type of
nailer is a nail jam. A jammed nail must be
cleared before using the nailer again. The
two places where a nail can get jammed
are the magazine and the discharge area.
To select single or bump fire operation:
1. Disconnect the air supply from the
nailer!
To clear a jammed nail from the magazine:
2. Locate the single/bump fire selector
on the trigger. See Figure 5.
3. To select Single Fire mode, push in
the selector and rotate it down.
4. To select Bump Fire mode, push in
the selector and rotate it up.
1. Disconnect the nailer from the air
supply!
2. Pull the magazine pusher all the way
back until it locks in place.
3. Locate and remove the jammed nail
with a pair of needle nose pliers. Close
the magazine cover so it latches.
To clear a jammed nail from the dis-
charge area:
1. Disconnect the nailer from the air
supply!
2. Pull the magazine pusher all the way
back until it locks in place.
3. Remove all nails from the magazine.
4. Locate the nail inside of the nailer
nose.
Figure 5. Single/bump fire selector.
5. Find a tool that will fit inside the slot on
the underside of the nose and dis-
lodge the nail.
6. Throw the damaged nail away and
insert a new nail stick that only con-
tains clean, undamaged nails. DO
NOT use dirty or damaged nails in
your nailer!
Always disconnect air from nailer
whenever clearing a jammed nail!
-8-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Nailer
Use a good solvent to clean the nose
assembly of the nailer. Always be sure that
the nailer is dry before using it again.
Do not allow dust, chips, sand, etc. into the
air connectors or into the body of the nail-
er; this may result in leaks and damage to
the nailer and the air fittings.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
Never use gasoline or other flamma-
ble liquids to clean this tool. Vapors
in the tool may ignite, causing the
tool to explode. Ignoring this warning
may lead to serious personal injury or
even death!
-9-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
6. Open the magazine.
7. Watch the discharge area and push
the top of the piston with your finger.
You will see the piston shaft slide
down the discharge area.
Replacing Pistons/O-Rings
If you use your nailer day in and day out,
Grizzly offers repair pistons as cheap
insurance against wasted down time and
lost profits in the event that a piston or pis-
ton shaft becomes worn out.
8. With a long flathead screwdriver or
similarly shaped tool, push the piston
shaft back inside the nailer until you
can grip the piston head and remove
it from the cylinder. (Be careful not to
scratch the discharge area when
pushing the piston shaft with the
screwdriver.)
9. Place a new O-ring on the new piston
and apply a thin film of the nailer lubri-
cating oil on the O-ring.
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide at the bottom of the cylinder.
The new piston should easily slide
into the cylinder. DO NOT force the
piston into the cylinder! If the piston
is not easily inserted, double-check
the alignment of the piston shaft with
the grooves on the guide.
11. After the piston is inserted correctly,
close the magazine. Replace the rear
cap assembly and tighten the 4 cap
screws.
12. For more assistance, or to install a
complete O-ring set, refer to the
appropriate breakdown diagram in the
back of this manual.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
To replace a piston:
1. Disconnect the nailer from the air
supply!
2. Remove all nails from the magazine
cartridge.
3. Remove the 4 cap screws from the
nailer exhaust cap.
4. Remove the exhaust cap as shown in
Figure 6.
Figure 6. Removing nailer exhaust cap.
-10-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
H5571 PART BREAKDOWN
-11-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
4
5
6
7
8
9
PSB115M
BTN HD CAP SCR M6-1 X 16
45 PH5571045 O RING
PH5571002 EXHAUST COVER
46 PH5571046 O RING
PH5571004 RUBBER WASHER 10MM
47 PH5571047 VALVE PLUNGER
48 PH5571048 O RING
PSB06M
CAP SCREW M6-1 X 25
PH5571006 CAP
49 PH5571049 SPRING
50 PH5571050 PLUNGER
51 PH5571051 O RING
PW09M
FLAT WASHER 7MM
PH5571008 SPACER
PH5571009 PISTON STOPPER
52 PH5571052 PLUNGER CAP
53A PH5571053A TRIGGER ASSEMBLY
56 PH5571056 PUSHER
57 PH5571057 STOPPER
58 PH5571058 SPRING
59 PH5571059 GASKET
60 PH5571060 SET PIN
10 PH5571010 SPRING
11 PH5571011 O RING
12 PH5571012 PISTON HEAD VALVE
12-1 PH5571012-1 SPACER
13 PH5571013 O RING
14 PH5571014 SEAL
15-1 PH5571015-1 O RING
61 PSB26M
CAP SCREW M6-1 X 12
15-2 PH5571015-2 O RING
62 PH5571062 SPIRAL SPRING
63 PH5571063 ROLLER
16A PH5571016A PISTON ASSEMBLY
19 PH5571019 CYLINDER RING
20 PH5571020 O RING
64 PH5571064 BALL PIN
65 PH5571065 MAGAZINE
66 PH5571066 NAIL GUIDE LINER
21 PH5571021 CYLINDER
21-1 PH5571021-1 O RING
67 PSB26M
CAP SCREW M6-1 X 12
22 PH5571022 BUMPER UPPER
23 PH5571023 GASKET
24 PH5571024 BODY
68 PH5571068 DEBRIS SHIELD
70 PH5571070 STOPPER BLOCK
72 PSB117M
BTN HD CAP SCR M5-.8 X 8
25 PH5571025 BUMPER BOTTOM
26 PH5571026 O RING
73 PH5571073 BRACKET
74 PLN04M
78 PSB116M
LOCK NUT M8-1.25
BTN HD CAP SCR M5-.8 X 14
27 PH5571027 NOSE
28 PSB31M
CAP SCREW M8-1.25 X 25
80 PH5571080 3/8" NPT CONNECTOR
82 PW01M FLAT WASHER 8MM
29 PH5571029 PIN
30 PH5571030 RUBBER RING
83 PH5571083 GASKET WASHER
84 PH5571084 PIN
31 PSB116M
BTN HD CAP SCR M5-.8 X 14
32 PH5571032 GUIDE SAFETY LEVER
34A PH5571034A SAFETY LEVER ASM.
85 PH5571085 SPACER
87 PH5571087 PISTON GUIDE WASHER
35 PLN02M
LOCK NUT M5-.8
88 PLW04M
89 PW05M
90 PSB18M
LOCK WASHER 8MM
FLAT WASHER 4MM
CAP SCREW M4-.7 X 8
36 PH5571036 SPRING
37 PH5571037 SAFETY LEVER
38 PLN03M
LOCK NUT M6-1
91 PH5571091 SPRING
92 PH5571092 SET BALL
95 PH5571095 IDLE ROLLER
39 PH5571039 DEPTH ADJUSTING KNOB
40 PH5571040 RUBBER PAD
41 PH5571041 O RING
96 PSB118M
BTN HD CAP SCR M5-.8 X 20
42 PH5571042 O RING
97 PH5571097 MAGAZINE BLOCK
100 PH5571100 ROLLER
43 PH5571043 VALVE
44 PH5571044 O RING
-12-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CAUSE
PROBLEM
ACTION
1. O-rings in trigger valve
housing are damaged.
1. O-rings must be replaced
Air leaking at trigger valve
area.
&
operation of safety
yoke must be checked.
1. Loose screws in housing.
2. Damaged O-ring.
3. Loose air fitting.
1. Tighten screws.
2. Replace O-ring.
3. Tighten air fitting.
Air leaking between hous-
ing and hose.
1. Damaged seal.
1. Air leaks.
1. Replace damaged seals.
Air leaking between hous-
ing and cap assembly.
1. Tighten screws and fit-
tings.
Tool skips nails while dis-
charging.
2. Dirt in nose.
2. Clean nose.
3. Dirt or damage prevents
nails from moving freely in
magazine.
3. Clean magazine and
inspect/repair damage.
4. Inadequate air flow to tool.
4. Check fitting, hose, com-
pressor & air pressure.
5. Replace piston O-ring.
Lubricate.
5. Worn O-ring on piston or
lack of lubrication.
6. Damaged O-rings on trigger
valve.
6. Replace trigger valve O-
rings.
7. Worn bumper.
8. Cap seal leaking.
7. Replace bumper.
8. Replace cap seal.
1. Nailer is not sufficiently lubri-
cated.
2. Broken spring in cap assem-
1. Lubricate nailer.
2. Replace spring.
Tool runs slowly or has a
loss of power.
bly.
3. Exhaust port in cap is
blocked.
3. Clean or replace dam-
aged internal parts.
1. Nails are the wrong size.
2. Nails are bent.
3. Magazine or nose screws
are loose.
1. Use correct nails.
2. Use undamaged nails.
3. Tighten magazine and
nose screws.
Fasteners frequently jam
the nailer.
4. Driver or driver guide are
worn or damaged.
4. Replace worn or dam-
aged parts.
5. Nails are wrong angle.
5. Use correct angle nails.
1. Nail is jammed in maga-
zine or discharge area.
1. Clear nailer magazine or
discharge area.
Nailer does not fire.
2. Piston shaft is damaged.
3. Air pressure too low.
2. Replace piston shaft.
3. Check/increase air pres-
sure.
H5571 34˚ Framing Nailer Kit
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-14-
H5571 34˚ Framing Nailer Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #_______________Serial#________________Order #______________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
_________________________________________
_________________________________________
_________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good value?
___Yes
___No
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
7. How many of your woodworking machines are
Grizzly? _____________
___Yes
___No
8. Which benchtop tools do you own? Check all
that apply.
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT NAIL
Download from Www.Somanuals.com. All Manuals Search And Download.
|