BANJO KIT
MODEL H3124
INSTRUCTION MANUAL
COPYRIGHT © FEBRUARY, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
JOB #5466 PRINTED IN JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SECTION 1: SAFETY ................................................................................................................................2
SECTION 2: INTRODUCTION....................................................................................................................3
SECTION 3: PARTS INVENTORY ............................................................................................................4
SECTION 4: SANDING ..............................................................................................................................5
Supplies/Tools......................................................................................................................................5
Wooden Rim ........................................................................................................................................5
Neck ....................................................................................................................................................6
Fingerboard..........................................................................................................................................6
Bridge ..................................................................................................................................................6
SECTION 5: FINISHING ............................................................................................................................7
Wooden Rim ........................................................................................................................................7
Neck ....................................................................................................................................................7
SECTION 6: ASSEMBLY ..........................................................................................................................8
Bracket Hook Lugs ..............................................................................................................................8
Tone Ring ............................................................................................................................................8
Banjo Head ..........................................................................................................................................9
Neck ..................................................................................................................................................10
Coordinator Rod ................................................................................................................................10
5th String Nut ....................................................................................................................................11
5th String Peg ....................................................................................................................................11
Tuning Machines................................................................................................................................12
Tailpiece ............................................................................................................................................12
Winding Strings..................................................................................................................................13
Bridge Placement ..............................................................................................................................13
String Height ......................................................................................................................................14
Tuning ................................................................................................................................................15
SECTION 7: REFERENCE INFO ............................................................................................................16
General ..............................................................................................................................................16
Aftermarket Accessories ....................................................................................................................16
Notes..................................................................................................................................................17
Warranty & Returns............................................................................................................................18
Warranty Card....................................................................................................................................19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
Always wear safety glasses or goggles when operating equipment. Everyday glasses or
reading glasses are not safety glasses. Be certain the safety glasses you wear meet the
appropriate standards of the American National Standards Institute (ANSI).
Because there are various ways to cut and join wood, you can make substitutions for the meth-
ods stated in this plan. We try to suggest the easiest methods possible. However, only you know
your skills with each piece of machinery. Never compromise your safety by using a cutting method
with which you are not comfortable. Instead, find an alternative approach that will yield the same
result.
These instructions assume that you are intimately familiar with the safe operation and use of
woodworking machinery and woodworking tools, and understand the techniques used to repro-
duce this project. If you do not qualify for both of these criteria, STOP building this project for
your own safety. Read and understand the owners manual for the machinery you intend to use,
take a woodworking class or visit your local library for more information. Woodworking machinery
and tools are inherently dangerous because they use sharp edges that can and will cause serious
personal injury including amputation and death. Do not underestimate the ability of these tools and
machinery to cause injury. Never operate any tool without all guards in place and always wear
approved safety glasses. For your own safety, please heed this warning.
-2-
H3124 Banjo Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INTRODUCTION
We are proud to offer the Model H3124 Banjo Kit.
Most importantly, we stand behind our products.
If you have any questions or parts requests,
please call or write us at the location listed below.
This kit is part of a growing Grizzly family of fine
woodworking products. When assembled accord-
ing to the guidelines set forth in this manual, you
can expect years of enjoyment from this banjo.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
We are pleased to provide this manual with the
Model H3124. It was written to guide you through
assembly, review safety considerations, and
cover general information. It represents our effort
to produce the best documentation possible.
E-Mail: [email protected]
If you have any comments regarding this manual,
please write to us at the address below:
The specifications, drawings, and photographs
illustrated in this manual represent the Model
H3124 as supplied when the manual was pre-
pared. However, owing to Grizzly’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
For your convenience, we always keep current
Grizzly manuals available on our website at
reflected in these manuals as soon as they are
complete. Visit our site often to check for the lat-
est updates to this manual!
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
H3124 Banjo Kit
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: PARTS INVENTORY
REF
PART #
DESCRIPTION
1
2
3
4
5
PH3124001 Wooden Rim
PH3124002 Brass Tone Ring
PH3124003 Banjo Head
PH3124004 Tension Hoop
PH3124005 Bracket Hook Assembly
8
15
4
2
5-1 PH3124005-1 Bracket Hook Lugs
5-2 PS56M
5-3 PLW02M
1
Phlp Hd Scr M4-.7 X 16
Lock Washer 4mm
3
12
6
PH3124006 Bracket Hooks
6-1 PH3124006-1 Bracket Hook Nuts
PH3124007 Coordinator Rod
7
7
18
7-1 PW01M
7-2 PW04M
8
Flat Washer 8mm
Flat Washer 10mm
Figure 1. Boxed components.
PH3124008
Neck with Top and 5th String Nuts
Tap Screw #10 X 2
8-1 PHTEK15
9
PH3124009 Pegs with Nuts and Washers
10 PH3124010 Truss Rod Cover with Screws
11 PH3124011 5th String Peg
12 PH3124012 Tailpiece
13 PH3124013 Bridge
14 PH3124014 Strap Hook
15 PH3124015 Strings
17
7-2
13
7-1
16
8-1
19
10
14
16 PH3124016 T-wrench
6
17 PH3124017 Truss Rod Wrench
18 PH3124018 Adjustable Wrench
19 PH3124019 Tailpiece Lug
5-1
6-1
5-2
5-3
Figure 2. Hardware Bag.
11
9
Figure 3. Peg Bag.
H3124 Banjo Kit
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: SANDING
Supplies/Tools
Wooden Rim
The majority of the wooden components in this kit
are fully machined from the factory and are ready
for assembly. A small amount of sanding and fin-
ishing will need to be performed to complete the
banjo.
The banjo wooden rim has been rough sanded at
the factory; however, no finish has been applied.
To sand the wooden rim:
1. Wear an ANSI-approved respirator and
safety glasses when sanding wood!
Recommended Tools & Supplies:
• Finishing Supplies
• #180, #240, and #320 Aluminum-Oxide
Sanding Paper
• Sanding Block
• Paste Filler
2. Using either an electric palm sander or a
sanding block, sand the wooden rim with
#180 grit aluminum-oxide sanding paper until
there is a consistent scratch pattern on the
entire surface. Note—When hand sanding,
always sand in the same direction as the
wood grain.
• ”000” Grade Steel Wool
• Masking Tape
• Razor Blade
• Razor Saw
• Long Shank Eye Screws
• Tack Cloth
3. Sand the wooden rim with a #240 grit sand-
ing paper until there is a consistent scratch
pattern on the entire surface.
• Coping, Jig, or Scroll Saw (Optional)
• Drill
4. Sand the wooden rim with a #320 grit sand-
ing paper until there is a consistent scratch
pattern on the entire surface.
• 4mm or 5/32" drill bit
• Hammer
5. Wipe the wooden rim with a damp cloth.
Wiping the workpiece with a damp cloth
before the final sanding helps to “raise” the
wood grain; thus, allowing the “raised” grain
to be sanded smooth.
6. Once the wooden rim is dry, repeat step 4.
7. Fill the wood pores with a paste filler accord-
ing to the manufacturer’s instructions.
8. When the paste filler is dry, use “000” grade
steel wool to remove the residue and polish
the wood surface.
9. Wipe the wooden rim with a tack cloth to
remove all remaining sanding dust.
H3124 Banjo Kit
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Neck
Fingerboard
Like the wooden rim, the banjo neck has been
rough sanded at the factory. Personalize the fret-
board and neck headstock with additional cutting,
inlay, or design work before final sanding. Note—
Take your time and consider testing your designs
in scrap wood before performing the work on the
actual fretboard and headstock.
The fingerboard requires no sanding. Note—
Sanding the fingerboard will affect the playability
of the banjo, and could lead to unrepairable dam-
age.
To sand the banjo neck:
1. Wear an ANSI-approved respirator and
safety glasses when sanding wood!
Bridge
2. Perform any custom cutting, inlay, or design
The bridge has been rough sanded at the factory.
Final sand the bridge as described in the
Wooden Rim sub-section.
work to the neck headstock.
3. Using the sanding technique described in the
previous sub-section, sand the entire banjo
neck, EXCEPT for the frets and fretboard.
Note—Sanding the fretboard and frets will
affect the playability of the banjo, and could
lead to unrepairable damage.
-6-
H3124 Banjo Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: FINISHING
Wooden Rim
Neck
Finishing supplies are not included with the banjo
kit. Note—The wooden rim and neck are made of
mahagony wood. Clear finishes such as lacquer
look exceptionally stunning and glossy on this
wood.
To finish the neck:
1. Wear an NOISH/OSHA approved respira-
tor with particulate and gas/vapor filters,
safety glasses, and rubber gloves, when
using finishing materials!
To finish the wooden rim:
2. Always work in a well ventilated area
when using finishing materials.
1. Wear a NOISH/OSHA approved respirator
with particulate and gas/vapor filters,
safety glasses, and rubber gloves, when
using finishing materials!
3. Mask off the fretboard. Use a small stick of
wood to carefully press all the masking tape
edges securely to the banjo fretboard. The
finish coat can seep under these edges,
especially near corners, uneven edges, and
places where the frets meet the fingerboard.
2. Always work in a well ventilated area
when using finishing materials.
3. Thread a long shank screw eye into one of
the holes in the wooden rim.
4. Form a piece of wire into a U shaped hanger
with hooks on both ends.
4. Hold the screw eye and apply several thin
coats of the finish. Multiple thin coats usually
produce a nicer finish than one heavy coat.
Note—Always follow the finish manufactur-
er’s instructions.
5. Thread the hooks through the upper peg-
holes and hang the neck in the finish room.
6. Apply several thin coats of the finish. Multiple
thin coats usually produce a nicer finish than
one heavy coat. Note—Always follow the fin-
ish manufacturer’s instructions.
5. Hang the wooden rim to dry.
Painting/Finishing Tips:
7. Hang the neck in a dust free room to dry.
Dust particles suspended in the air will settle on
wet finishes, causing less than satisfactory
results. To avoid this problem:
8. When finishing is complete, remove the
masking tape from the fretboard.
9. Carefully scrape any excess finish off the
• Leave the finishing room undisturbed for 24
hours prior to applying the finish.
fretboard with a razor blade.
• Avoid making unnecessary movements upon
entering the finish room.
• Apply the finish to the desired banjo parts and
immediately leave the finish room.
• DO NOT return to the room until the specified
drying time has elapsed.
H3124 Banjo Kit
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: ASSEMBLY
Bracket Hook Lugs
Tone Ring
The bracket hook lugs provide a secure anchor
for the bracket hooks.
The tone ring transmits vibration from the banjo
head into the rim. It is essential to shaping the
sound of the instrument.
To install the bracket hook lugs:
To install the tone ring:
1. Slide the M4-.7 X 16 Phillip head screws with
4mm lock washers through the holes on the
centerline of the wooden rim and thread the
bracket hook lugs onto the screws as shown
in Figure 4.
1. Use a razor blade to scrape excess finish out
of the groove in the wooden rim.
2. Test the fit of the ring. It should fit snug onto
the wooden rim.
3. Install the tone ring with the flat side down as
shown in Figure 5.
Figure 4. Installing the bracket hook lugs.
2. Rotate the bracket hook lugs until the holes
face up and tighten the screws.
Figure 5. Installing the tone ring.
3. Attach the strap hook with the remaining
screw and lock washer into the hole that is
off center.
-8-
H3124 Banjo Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Ensure that the head is seated squarely on
the rim, and the bracket hooks are perpen-
dicular to the tension hoop.
Banjo Head
6. Use the included wrench to tighten the brack-
et hook nuts. Proceed clockwise, tightening
each nut 1⁄2 turn as shown in Figure 8.
To install the banjo head:
1. Press the banjo head onto the tone ring.
2. Place the tension ring over the banjo head.
See Figure 6.
Figure 8. Tightening the bracket hook nuts.
7. If the surface of the tension hoop is higher
than the fingerboard surface, tighten the
bracket hooks until the surfaces are equal.
Figure 6. Installing the tension hoop.
3. Drop the bracket hooks over the tension ring
and through the bracket hook lugs.
4. Thread the bracket hook nuts and 4mm lock
washers onto the bracket hooks and finger
tighten as shown in Figure 7. Note—The
bracket hook nuts install with the flat side
toward the bracket hook lugs.
Figure 7. Finger tightening the bracket hook nuts.
H3124 Banjo Kit
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Neck
Coordinator Rod
To install the coordinator rod:
To attach the neck to the banjo rim:
1. Thread the remaining nut and a washer into
1. Place the neck fretboard-side-down on a non
marring surface and insert the coordinator
bolt into the heel of the neck.
the center of the coordinator rod.
2. Thread the coordinator rod through the hole
in the rim from the inside. Note—The washer
needs to be between the nut and the banjo
rim.
2. Thread the #10 X 2 tap screw into the neck
and through the coordinator bolt as shown in
Figure 9.
3. Thread the tailpiece lug and a washer onto
the coordinator rod. Make sure the coordina-
tor rod does not block the hole in the tailpiece
lug.
4. Thread the coupler onto the coordinator rod
and the coordinator bolt, as shown in Figure
10, and finger tighten only.
Coordinator Rod Nut
Coupler
Coordinator Rod
Figure 9. Installing the coordinator bolt.
3. Attach the neck to the rim by feeding the
coordinator bolt through the large hole in the
banjo rim, and threading the large bolt and
washer tightly against the rim. Tighten with
the included adjustable wrench.
Coordinator Bolt
Coordinator Rod Nut
Figure 10. Installing the coordinator rod.
5. Tighten the coordinator rod nuts and washer
against the banjo rim.
-10-
H3124 Banjo Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
5th String Nut
5th String Peg
the 5th string nut is installed in the banjo neck just
above the 5th fret. It is necessary to cut a very
shallow slot in this nut to guide the 5th string. The
slot should be deep enough so the 5th string does
not slide out, but a buzz will occur when the
instrument is played if it is cut deeper than the
height of the 5th fret.
The 5th string peg is the smallest of the tuners
and is made to be force fitted into the peg hole.
To install the 5th string peg:
1. Clean any excess finish out of the peg hole.
2. Remove the knob and plastic washer from
To cut the 5th string slot in the nut:
the 5th string peg.
1. Use a razor saw or a small jewelers file to
carefully cut a slot that is .01" (.25mm) deep
or less .
3. Put a few drops of wood glue on the 5th
string peg and insert it into the peghole with
the tuning post towards the fretboard.
2. Slide the 5th string in the slot. The 5th string
4. Place the T-wrench over the 5th string peg,
shown in Figure 12, and carefully drive the
5th string peg into the peghole with a ham-
mer. Note—Place a non-marring support
under the banjo neck before tapping.
should be flush with the top of the nut.
3. Carefully cut the slot deeper if the string is
not flush with the top of the nut.
5th String Nut
Figure 12. Inserting the 5th string peg.
Figure 11. 5th string nut.
5. Replace the plastic washer and knob on the
5th string peg.
H3124 Banjo Kit
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning Machines
Tailpiece
To install the tuning machines:
To install the tailpiece:
1. Slide the tuning machines through the back
1. Insert the tailpiece screw through the tail-
of the headstock.
piece lug.
2. Place the washer and barrel nut over the tun-
2. Set the tailpiece on the tensioning hoop, as
shown in Figure 14, and tighten the nut
against the tailpiece lug.
ing post and tighten with a 10mm socket.
Tailpiece
Tailpiece Lug
Figure 13. Tuning machines installed in the
Figure 14. Tightening tailpiece screw into lug.
back of the headstock
-12-
H3124 Banjo Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Winding Strings
Bridge Placement
Install the banjo strings loosely. The bridge must
be installed and adjusted before the strings can
be tightened and tuned.
To place the bridge:
1. Lay the bridge flat on the banjo head and
slide it under the strings.
To install the banjo strings:
2. Slowly tilt the bridge up under the strings.
Loosen the strings if it is difficult to raise the
bridge.
1. Place the end of the string with the loop over
the hooks on the tailpiece. The 1st string is
farthest to the right, then 2nd, 3rd, 4th, and
5th farthest to the left as shown in Figure 15.
3. Slide the strings into their slots and tighten.
4. The bridge location is 696mm (27.4") if mea-
sured from the nut and 348mm (13.7") if
measured from the 12th fret. See Figure 16.
5th String
1st String
Figure 15. String placement.
2. Pull the strings through the tailpiece holes
and up to the tuners. Do not overlap the
strings.
Figure 16. Bridge placement.
5. Finalize the position of the bridge by lightly
touching the 1st string directly above the
twelfth fret and plucking the string to play a
harmonic note.
3. Route the 5th string to the inside of the 5th
string nut and down to the 5th string peg.
4. Route the strings to the inside of the tuning
posts and through the peg holes. Note—
Allow enough string slack to allow 2-3 com-
plete winds around the tuning peg.
6. Now pluck the string while holding it against
the twelfth fret. If this note is sharper than the
note played in step 5, move the 1st string
side of the bridge toward the tailpiece. If this
note is flat in comparison, move the bridge
toward the neck.
5. Turn the tuning knobs to tighten the strings.
Note—DO NOT completely tighten the
strings at this time.
7. This can also be done with an electronic
tuner by tuning the harmonic note to be
exactly in tune and then adjusting the bridge
until the note played in step 6 is also in tune.
H3124 Banjo Kit
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Measure the string heights at the 22nd fret.
9
String Height
The string should be ⁄64" above the fret.
Note—The 22nd fret is the closest to the
banjo body.
Correct string height is crucial to prevent fret buzz
and maximize playability. The string height is
measured from the top face of the fret and the
bottom face of the string.
3. Turn the coordinator rod to adjust the string
height as shown in Figure 19. Note—DO
NOT adjust string height more than 1⁄16". This
may cause damage to the banjo rim.
String
Lower String
Height
String Height
Fret
Fingerboard
Raise String
Height
Figure 17. String height measurement.
Figure 19. Adjusting string height.
To check the string height:
4. If the strings need to be adjusted more than
1⁄16", shim the bottom of the neck to increase
string height, or shim the top to decrease the
string height.
1. Measure the string heights at the 12th fret
from the peghead (Figure 18). The string
1
should be ⁄8" above the fret. Note—Use a
steel ruler with a resolution of 1⁄64".
Banjo Body
String Heights: 1⁄8
"
12th Fret
Figure 18. Correct 12th fret string heights.
-14-
H3124 Banjo Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Important issues to consider when tuning a
banjo:
Tuning
•
Get into the habit of tuning the banjo every
time it is picked up to be played.
Tuning is the most important concept of playing a
banjo. If the banjo is not in tune with itself, or the
other instruments in an ensemble, the resulting
music will not sound pleasing to the ear. Banjo
players use many different tunings, but the most
common (“G”) is shown in Figure 20.
•
Always tune the strings “up.” The final tuned
tension of each string should be reached
while tightening the string, not loosening it. If
the string is tensioned too far, loosen the ten-
sion and tune ”up” again.
•
The easiest way to tune a banjo is using an
electronic tuner such as the Grizzly H3097
Chromatic Tuner shown on page 16.
G
G
D
5
3
1
D
B
4
2
D - 4th string (one octave
lower than the 1st string)
G - 3rd string (one octave
lower than the 5th string)
Figure 20. Standard tuning notes.
H3124 Banjo Kit
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: REFERENCE INFO
General
Aftermarket
Accessories
If you need parts or help in assembling your
banjo, or if you need operational information, call
the service department at (570) 546-9663.
Trained service technicians will be glad to help
you.
If you have any comments regarding this manual,
please write to Grizzly at the address below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
Figure 21. Model H3097 Chromatic Tuner.
We recommend you keep a copy of our current
catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
banjo, or if you need general assistance or
replacement parts, please contact the Service
Department at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
-16-
H3124 Banjo Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
H3124 Banjo Kit
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty & Returns
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse; abuse;
negligence; accidents; repairs or alterations; assembly, finishing or modification of kits; or lack of mainte-
nance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, includ-
ing any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this writ-
ten warranty. We do not warrant or represent that the merchandise complies with the provisions of any law
or acts unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed
the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the
State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe-
cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the car-
ton. We will not accept any item back without this number. Proof of purchase must accompany the mer-
chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
H3124 Banjo Kit
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Card
Name ____________________________________________________________________________________
Street ____________________________________________________________________________________
City ______________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_______________________FAX________________________
MODEL #_______________________________________________ Order #______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
1.
How did you learn about us?
9.
How many of your woodworking machines are Grizzly? _____________
Which benchtop tools do you own? Check all that apply.
___Advertisement
___Catalog
___Friend
___Card Deck
___World Wide Web
10.
___Other__________________________________________________
Which of the following magazines do you subscribe to.
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
2.
___American Woodworker
___Cabinetmaker
___Practical Homeowner
___Shop Notes
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
___Today’s Homeowner
___WOOD
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Woodworker
___Woodworker’s Journal
___Workbench
___Other__________________________________________________
How many of the machines checked above are Grizzly? ____________
11.
12.
Which portable/hand held power tools do you own? Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
3.
___Miter Saw
___Backyard America
___Home Time
___The American Woodworker
___The New Yankee Workshop
___This Old House
___Woodwright’s Shop
___Other__________________________________________________
What machines/supplies would you like Grizzly Industrial to carry?
13.
___Other__________________________________________________
What is your annual household income?
__________________________________________________________
__________________________________________________________
What new accessories would you like Grizzly Industrial to carry?
__________________________________________________________
__________________________________________________________
What other companies do you purchase your tools and supplies from?
__________________________________________________________
__________________________________________________________
Do you think your purchase represents good value?
4.
5.
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
14.
15.
What is your age group?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
6.
7.
8.
How long have you been a woodworker?
16.
17.
18.
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Yes
Would you recommend Grizzly Industrial to a friend?
___Yes ___No
___No
How would you rank your woodworking skills?
___Simple
___Intermediate
___Advanced
___Master Craftsman
Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.
What stationary woodworking tools do you own? Check all that apply.
___Yes
___No
___Air Compressor
___Bandsaw
___Drill Press
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Panel Saw
___Planer
19.
Comments:_________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
___Power Feeder
___Radial Arm Saw
___Shaper
___Spindle Sander
___Table Saw
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
___Other__________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
Visit Our Website Today And Discover Why
Grizzly® Is The Industry Leader!
• SECURE ORDERING
• ORDERS SHIPPED WITHIN 24 HOURS
• E-MAIL RESPONSE WITHIN ONE HOUR
-OR-
Call Today For A
FREE
Full Color Catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
|