MODEL T27313
WOOD LATHE COPY ATTACHMENT
OWNER'S MANUAL
(For models manufactured since 01/15)
(Model T27313 shown installed on Model G0733)
COPYRIGHT © MARCH, 2015 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BB17314 PRINTED IN CHINA
V1.03.15
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION............................................................................................................................... 2
Machine Description................................................................................................................... 2
Contact Info................................................................................................................................ 2
Manual Accuracy........................................................................................................................ 2
Controls & Components............................................................................................................. 3
SECTION 1: SAFETY....................................................................................................................... 4
Safety Instructions for Machinery............................................................................................... 4
Additional Safety for Copy Attachments .................................................................................... 6
SECTION 2: SETUP......................................................................................................................... 7
Unpacking .................................................................................................................................. 7
Needed for Setup....................................................................................................................... 7
Inventory..................................................................................................................................... 7
Cleanup...................................................................................................................................... 8
Site Considerations.................................................................................................................... 9
Assembly.................................................................................................................................. 10
SECTION 3: OPERATIONS ........................................................................................................... 14
Operation Overview.................................................................................................................. 14
Workpiece Inspection............................................................................................................... 15
Copy Attachment Tips.............................................................................................................. 15
Copy Stylus.............................................................................................................................. 16
Cutting Tool.............................................................................................................................. 16
Basic Operation........................................................................................................................ 17
SECTION 4: ACCESSORIES......................................................................................................... 19
SECTION 5: MAINTENANCE......................................................................................................... 20
Schedule .................................................................................................................................. 20
Cleaning & Protecting .............................................................................................................. 20
Lubrication................................................................................................................................ 20
SECTION 6: SERVICE ................................................................................................................... 21
Troubleshooting........................................................................................................................ 21
Cable Tension.......................................................................................................................... 22
Gib Adjustment......................................................................................................................... 22
SECTION 7: PARTS....................................................................................................................... 23
Main Breakdown....................................................................................................................... 23
Longitudinal Drive Breakdown ................................................................................................. 25
Carriage Breakdown................................................................................................................. 26
WARRANTY & RETURNS ............................................................................................................. 29
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Machine Description
Manual Accuracy
The Model T27313 Wood Lathe Copy attachment
is part of Grizzly’s growing family of fine wood-
working and metalworking machinery. When used
according to the guidelines stated in this manual,
you can expect years of trouble-free, enjoyable
operation.
We are proud to provide a high-quality owner’s
manual with your new machine!
We made every effort to be exact with the instruc-
tions, specifications, drawings, and photographs
contained inside. Sometimes we make mistakes,
but our policy of continuous improvement also
means that sometimes the machine you receive
will be slightly different than what is shown in
the manual.
The Model T27313 is a wood lathe duplica-
tor capable of mass-producing many shapes
of the same design. The T27313 is designed to
be mounted to the G0733, G0462, G0584 and
G5979 wood lathes. Mounting hardware and cut-
ting tool are provided with the Copy attachment.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure, check our website
for an updated version. We post current manuals
and manual updates for free on our website at
Contact Info
Alternatively, you can call our Technical Support
for help. Before calling, please write down the
Manufacture Date and Serial Number stamped
into the machine ID label (see below). This infor-
mation helps us determine if updated documenta-
tion is available for your machine.
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Email: [email protected]
Manufacture Date
Serial Number
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
-2-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Tool Locking Collar: Hardware that keeps
Controls &
Components
cutting tool locked in place.
E. Quill: Moves cutting tool mounted in the car-
riage toward or away from the workpiece.
F. Carriage: Main housing for quill, cutting tool,
and tool locking collar. Moves longitudinally
along copy attachment bed.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
G. Stylus: Controls depth of cut.
H. Crossfeed Handwheel: Controls crossfeed
leadscrew, which sets maximum cutting tool
depth. Turning clockwise decreases cutting
depth and turning counterclockwise increas-
es cutting depth.
Refer to Figure 1 and the following descriptions
to become familiar with the basic controls of this
machine.
I. Tail Center Adjustment Knob: Adjusts
position of tail center. Used to hold master
spindle in place.
H
F
D
B
E
G
C
A
J. Bed: Main body of copy attachment to which
all other parts attach.
K. Template Support: Brackets that allow tem-
plates to securely mount to copy attachment.
I
J
K
Figure 1. T27313 controls and components.
A. Longitudinal Feed Cable: Cable that con-
nects carriage to longitudinal feed wheel
allowing carriage to travel along copy attach-
ment bed.
B. Adjustable Carriage Stop: Limits carriage
travel along length of copy attachment bed.
C. Longitudinal-Feed Handwheel: Rotating
clockwise moves carriage to the left, rotating
counterclockwise moves carriage to the right.
-3-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand this ELECTRICAL EQUIPMENT INJURY RISKS. You
owner’s manual BEFORE using machine.
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
TRAINED OPERATORS ONLY. Untrained oper-
ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
DISCONNECT POWER FIRST. Always discon-
nect machine from power supply BEFORE making
adjustments, changingtooling, orservicingmachine.
This prevents an injury risk from unintended startup
or contact with live electrical components.
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-4-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
WEARING PROPER APPAREL. Do not wear FORCING MACHINERY. Do not force machine.
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work-
piece control.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a NIOSH-approved respirator to
reduce your risk.
STABLE MACHINE. Unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. Using improper acces-
sories will increase the risk of serious injury.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica-
tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect safe
operation. Immediately repair or replace damaged
or mis-adjusted parts before operating machine.
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.
-5-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety for Copy Attachments
MAIN INJURY HAZARDS: Death or crushing injury from getting entangled in rotating lathe
spindle or workpiece; death, blindness, or broken bones from being struck by a workpiece that
breaks apart or comes loose during rotation, turning tool kickback, or flying wood chips. To
minimize your risk of these hazards, always heed the following warning information:
LATHE OPERATIONS. Refer to your lathe own- EYE/FACE PROTECTION. Always wear a face
er’s manual for all lathe related operations.
shield and safety glasses when operating lathe.
PROPER SETUP. Ensure copy attachment is PROPER APPAREL. Do not wear gloves, necktie
properly setup and adjusted before operating.
or loose clothing. Keep keep long hair away from
rotating spindle.
INTEGRITY OF STOCK. Verify each workpiece
is free of knots, splits, nails, or foreign material NEW SETUPS. Test each new setup by starting
to ensure it can safely rotate on spindle without spindle rotation at the lowest speed and standing
breaking apart or causing turning tool kickback.
to the side of the lathe until workpiece reaches full
speed and you can verify safe rotation.
WORKPIECE PREPARATION. Before mounting,
cut off waste portions with a bandsaw or other tool ROUGHING. Use correct cutting tool. Take light
to ensure workpiece has no large edges to catch cuts, use low speeds.
turning tool, and it will rotate without dangerous
wobbling.
SHARP CUTTING TOOLS. Only use sharp cut-
ting tools— they cut with less resistance than dull
SECURING LOCKS. Verify tool rest, headstock, tools. Dull cutting tools can catch or grab and
and tailstock are secure before turning lathe ON. cause workpiece to break apart.
SECURING WORKPIECE. An improperly secured STOPPING SPINDLE. Always allow spindle to
workpiece can fly off spindle with deadly force. completely stop on its own. Never put hands or
Use proven setup techniques and always verify another object on spinning workpiece.
workpiece is well-secured before starting lathe.
ADJUSTMENTS/MAINTENANCE. Make sure
ADJUSTMENT TOOLS. Remove all chuck keys, wood lathe is turned OFF, disconnected from
wrenches, and adjustment tools before turning power, andallmovingparts are completely stopped
lathe ON. A tool left on the lathe can become a before doing adjustments or maintenance.
deadly projectile when spindle is started.
MEASURING WORKPIECE. Only measure work-
SAFE CLEARANCES. Before starting spindle, piece after it has stopped. Trying to measure a
verify workpiece has adequate clearance by spinning workpiece increases entanglement risk.
hand-rotating it through its entire range of motion.
-6-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: SETUP
Unpacking
Inventory
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at (570) 546-9663 for advice.
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
Box 1 (Figure 2)
Qty
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
A. Copy Attachment........................................ 1
B. Longitudinal-Feed Handwheel.................... 1
C. Support Arm Clamping Plates.................... 2
D. Support Arms (Short) ................................. 2
E. Support Arms (Tall) .................................... 2
F. Hardware Bag (Not Shown)........................ 1
—T-Bolts M10-1.5 x 100 ............................. 2
—T-Bolts M10-1.5 x 45 ............................... 2
—Cutting Tool ............................................ 1
—Support Arm Clamps.............................. 2
—Fender Washers 8mm ........................... 2
—Hex Nuts M8-1.25 .................................. 2
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
Needed for Setup
A
The following are needed to complete the setup
process, but are not included with your machine.
B
Description
Qty
•
•
•
•
•
•
•
•
•
Additional People ....................................... 1
Safety Glasses ........................................... 1
Cleaner/Degreaser (Page 8) ...... As Needed
Disposable Shop Rags............... As Needed
Screwdriver Phillips #2............................... 1
Wrench or Socket 16mm............................ 1
Hex Wrench 4mm....................................... 1
Feeler Gauge ............................................. 1
Machinist's Square..................................... 1
E
D
C
Figure 2. T27313 inventory.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
-7-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleanup
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoid
using these products
to clean machinery.
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
Many cleaning solvents
are toxic if inhaled. Only
work in a well-ventilated
area.
There are many ways to remove this rust preven-
tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-
turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces.
Before cleaning, gather the following:
•
•
•
•
Disposable rags
Cleaner/degreaser (WD•40 works well)
Safety glasses & disposable gloves
Plastic paint scraper (optional)
T23692—Orange Power Degreaser
A great product for removing the waxy shipping
grease from your machine during clean up.
Basic steps for removing rust preventative:
1. Put on safety glasses.
2. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3. Wipe off the surfaces. If your cleaner/degreas-
er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
Figure 3. T23692 Orange Power Degreaser.
4. Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
-8-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Site Considerations
Physical Environment
Weight Load
The physical environment where the machine
is operated is important for safe operation and
longevity of components. For best results, oper-
ate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range is outside 41°–104°F; the relative humidity
range is outside 20–95% (non-condensing); or
the environment is subject to vibration, shocks,
or bumps.
Make sure that the surface upon which the
machine is placed will bear the weight of the
machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
151⁄2
"
55"
Figure 4. Working clearances (Model T27313 shown attached to example wood lathe).
-9-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Support Arms
1. DISCONNECT MACHINE FROM POWER!
Assembly
2. Mount (2) support arms perpendicular to,
and on top of, lathe bed with (2) support arm
clamping plates, (2) support arm clamps, (2)
M8-1.25 x 150 carriage bolts, (2) 8mm fender
washers, and (2) M8-1.25 knobs. Carriage
bolt head should be on top of support arm
clamp, and support arm clamping plates
should be below lathe bed (see Figure 6).
The assembly process consists of selecting the
appropriate support arm orientation, mounting
the support arms and copy attachment bed, and
finally aligning the copy attachment. The align-
ment procedures are critical to the proper opera-
tion of the copy attachment, DO NOT skip these
procedures.
Note: Leave knobs finger tight so support
arm assembly can slide across lathe bed.
All assembly and adjustment instructions
assume that your lathe is axially aligned,
i.e., headstock and tailstock are centered on
the same axis. Consult your lathe owner’s
manual for proper procedure.
Support Arm
Support Arm
Clamp
Lathe Bed
Carriage Bolt
Selecting correct support arm orientation
is critical to ensure that cutting tool will be
positioned at spindle centerline.
Fender Washer
Knob
Support Arm
Clamping Plate
Selecting Support Arm Setup
The support arms must be oriented in a specific
way depending on which lathe the copy attach-
ment will be mounted. Figure 5 shows the sup-
port arm orientation for each of the four wood
lathes onto which the model T27313 mounts. The
arms will be mounted on top of the lathe bed with
the mounting holes extending approximately 6"
past it.
Figure 6. Example of support arm assembly
setup for G0733 wood lathe.
(Viewed from Headstock)
G0733
G0584
(Rear
of
(Front
of
Bed)
Bed)
G0462
G5979
Figure 5. Support arm orientation and matching
lathe.
-10-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Adjust support arm assemblies so they are
centered on points measuring 20% of dis-
tance across lathe bed from headstock to
tailstock (see Figure 7). Front of support
arms should extend beyond front of lathe bed
by about 6".
6. Mount copy attachment so tool will reach cor-
rect starting point for desired cut.
7. Install (2) 10mm flat washers and (2) M10-
1.5 hex nuts onto T-bolts installed in Step 4.
Then tighten support arm assembly knobs.
— Some minor degree of variation may be
necessary to eliminate any interference to
normal operation of lathe.
— Make certain copy attachment does not
block access to lathe controls. Some lat-
eral adjustment can be made to assure
clearance if necessary (see Figure 9).
Support Arms
6"
60%
20%
20%
Figure 7. Attachment locations for support arms.
Figure 9. Example of copy attachment mounted
on lathe without obstructing lathe controls.
4. Tip copy attachment upside down so bot-
tom channel is facing upwards, then slide
(2) M10-1.5 x 100 T-bolts into channel (see
Figure 8).
8. Congratulations, your copy attachment has
been successfully installed. It must now be
aligned for parallelism. Please proceed to
Rough Alignment on Page 12.
— If using short support arms, use (2) M10-
1.5 x 45 T-bolts.
T-Bolt
T-Bolt
Channel
Figure 8. T-bolt installed into slot on bottom of
copy attachment (1 of 2).
5. Turn copy attachment right side up, then
insert T-bolts into support arm holes.
-11-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Loosen (2) knobs securing support arm
assemblies, then slide copy attachment bed
over boards until leading edge is even with
marks on both left and right sides (see Figure
10).
Performing Rough Alignment
Once the copy attachment bed is attached to the
support arms, the entire assembly must be adjust-
ed parallel with the lathe to function correctly.
The following procedures provide details on the
process of adjusting the copy attachment to
achieve parallelism.
6. Tighten (2) knobs securing support arm
assemblies to lathe bed.
7. Remove gauge boards.
8. Install longitudinal-feed handwheel with (1)
M6-1 x 12 cap screw and (1) 6mm flat washer
(see Figure 11).
Use caution when handling copy attach-
ment cutting tool. Its sharp edges could
cause cuts if handled improperly.
Longitudinal-Feed
Handwheel
To perform rough alignment:
1. DISCONNECT MACHINE FROM POWER!
2. Prepare two gauge boards approximately
11⁄8" thick, 6–8'' wide and 2–3'' long.
3. Clamp gauge boards onto lathe bed, one at
headstock and other at tailstock.
Figure 11. Longitudinal-feed handwheel installed
4. Place a machinist’s square centered on
tailstock on top of gauge board and measure
3'' toward copy attachment bed (see Figure
10). Place a precise mark across width of
wood. Repeat with gauge board located at
headstock.
on copy attachment.
9. Install cutting tool into arbor and tighten pre-
installed collar set screw (see Figure 12).
(View from Headstock)
Tailstock
Copy
Attachment
3"
Bed
Gauge
Board
Figure 12. Securing cutting tool.
Lathe Bed
10. Rough alignment is now complete. Please
proceed to Performing Final Alignment on
Page 13.
Figure 10. Use of gauge boards for alignment.
-12-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Without changing position of turning blank,
slowly turn longitudinal feed handwheel to
move carriage toward opposite end of lathe.
Use a feeler gauge or another precision
spacer to check that the distance between
cutter and turning square is consistent (see
Figure 14).
Performing Final Alignment
Final alignment of the lathe and copy attach-
ment must be precise to ensure they are parallel.
Before completing the following steps, mount a
turning square blank between the centers of your
lathe.
The turning square blank should be as long as the
maximum center-to-center distance of your lathe
to ensure the greatest degree of accuracy. It is
critical that the turning square blank is perfectly
centered and as near-perfectly straight as pos-
sible.
Avoid wearing loose-fitting clothing, jew-
elry, or other personal items that could be
caught in moving parts of the machinery
while adjusting or operating this machine.
Serious personal injury could result if this
warning is ignored.
Figure 14. Example of using precision spacer.
—If cutting tool does not maintain a consis-
tent distance from turning square at both
ends of longitudinal movement, loosen
support arm assembly knobs and care-
fully adjust bed until cutting tool is an equal
distance from turning square at both ends
of its longitudinal movement. Then tighten
support arm assembly knobs.
To perform final alignment:
1. DISCONNECT MACHINE FROM POWER!
2. Move carriage to one end of copy attach-
ment and advance cross-feed handwheel
until cutting tool nearly touches side of blank
(see Figure 13).
4. Continue to test and adjust copy attachment
until it is evenly spaced along length of turn-
ing square.
5. Once adjustments are complete, ensure all
mounting bolts are securely tightened.
Figure 13. Aligning lathe to copy attachment.
-13-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: OPERATIONS
To complete a typical operation, the operator
does the following:
Operation Overview
1. Examines workpiece to make sure it is suit-
The purpose of this overview is to provide the nov-
ice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
able for cutting.
2. Adjusts cutting tool and stylus to make sure
they are aligned.
3. Puts on safety glasses, face shield, and a
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual and seek additional training from expe-
rienced machine operators, and do additional
research outside of this manual by reading "how-
to" books, trade magazines, or websites.
respirator.
4. Turns lathe ON.
5. Gradually advances cutting tool over multiple
passes; until stylus makes contact with tem-
plate.
6. Turns lathe OFF immediately after turning
is complete and waits for workpiece to com-
pletely stop before removing it.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
7. Repeats Steps 1–6 to complete all copies.
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj-
ects. Regardless of the content in this sec-
tion, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
Eye injuries or respiratory problems can
occur while operating this tool. Wear per-
sonal protective equipment to reduce your
risk from these hazards.
-14-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Workpiece
Inspection
Copy Attachment
Tips
Some workpieces are not safe to turn or may
require modification before they are safe to
turn. Before turning a workpiece, inspect all
workpieces for the following:
•
•
To reduce whip and vibration of relatively
narrow copy spindles, we recommend oper-
ating the longitudinal handwheel with your left
hand and backing up the spinning workpiece
with your right. DO NOT attempt to grip the
workpiece too tightly while it is turning.
•
Workpiece Type:
This machine is intended for cutting natural
and man-made wood products, and some
plastics. Never attempt to cut any metal,
stone, or rubber workpiece; cutting these
materials can lead to machine damage or
severe injury.
If the cut you are producing is too rough, try
increasing the rotation speed of your lathe
(not to exceed the maximum recommended
speed for the size of material you are turn-
ing) and take a lighter cut. See your lathe’s
instruction manual for recommended speeds.
•
Foreign Objects:
Nails, staples, dirt, rocks and other foreign
objects are often embedded in wood. While
cutting, these objects can become dislodged
and hit the operator, cause tool grab, or break
the turning tool, which might then fly apart.
Always visually inspect your workpiece for
these items. If they can't be removed, DO
NOT turn the workpiece.
•
•
•
•
As with any other surfacing operation, we
recommend taking multiple passes, rather
than trying to remove too much wood all at
once. This is much safer and will also result
in improved cutting results.
When making copies, always move the stylus
so it follows the template or master profile
“downhill”. Trying to move the stylus “uphill”
along the template will cause the stylus and
cutter to dig into the template and workpiece.
•
Large/Loose Knots:
Loose knots can become dislodged during
the turning operation. Large knots can cause
a workpiece to completely break in half dur-
ing turning and cause machine damage and
personal injury. Choose workpieces that do
not have large/loose knots.
To avoid unnecessary waste of expensive
premium materials, we strongly recommend
you turn a test piece before attempting dupli-
cation on your finish material. Make adjust-
ments as required.
•
Excessive Warping:
Workpieces with excessive bowing or twist-
ing are unstable and unbalanced. Never turn
these workpieces at high speed, or instability
will be magnified and the workpiece can be
ejected from the lathe causing impact injures.
Only turn concentric workpieces!
You can save time during duplication by
removing the corners from all of the spindles
you plan on creating before activating the
copy attachment. You will need to make the
cuts with a lathe chisel on your tool rest, prior
to installing the copy attachment.
-15-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Copy Stylus
Cutting Tool
To ensure the greatest level of precision while
copying from a template or a master spindle, it
is essential that the copy stylus is properly posi-
tioned at the underside of the carriage. When
adjusting the stylus, keep in mind that its follower
edge should be centered on the template or mas-
ter profile, so the narrowest point fits securely.
The cutting tool can be positioned closer to or
farther from the workpiece by loosening the set
screw at the top of the cutting tool collar.
To install or replace cutting tool:
1. Loosen M8-1.25 x 16 set screw on cutting
tool collar shown in Figure 16.
To adjust stylus:
2. Insert cutting tool with triangular cutting edge
facing up (see Figure 16), then tighten set
screw.
1. DISCONNECT MACHINE FROM POWER!
2. Center master spindle on copy centers, or
attach template to support brackets.
Set Screw
3. Loosen M5-.8 x 10 set screw, then adjust
stylus height until the follower edge is cen-
tered on template or profile (see Figure 15).
Figure 16. Example of proper position for cutting
Set Screw
tool.
Figure 15. Stylus follower edge.
4. Tighten M5-.8 x 10 set screw to secure sty-
lus.
5. Run stylus along length of master spindle or
template.
— If stylus does not contact master spindle
or template details, move cutting tool
accordingly, and repeat Steps 3–4.
-16-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Mount template or master spindle onto copy
Basic Operation
attachment.
—If you are using a template, spread tem-
plate mounting brackets (see Figure 18)
apart to accommodate template. Drill holes
in your template and secure it to mounting
brackets. Position template on copy attach-
ment main body so profile will line up with
desired location of profile on workpiece.
Make sure headstock and tailstock centers
are properly aligned before beginning any
turning operation. See your lathe owner's
manual for additional instructions on this
procedure. Failure to observe this warning
could result in workpiece being thrown from
lathe, resulting in serious personal injury.
To make copies from existing spindle or tem-
plate:
Mounting
Bracket
1. DISCONNECT MACHINE FROM POWER!
2. Mount workpiece on lathe.
3. Move carriage with longitudinal handwheel
until tip of cutter is precisely located at point
on workpiece where you want turning action
to begin.
Template
Figure 18. Template mounted to mounting
brackets.
Note: Always move stylus so it follows the
template “downhill”. Trying to move “uphill”
along the template will cause the stylus
and cutting tool to dig into the template and
workpiece (see Figure 17).
—If you are using a master spindle, mount
spindle between copy attachment centers.
Position and secure head center so exist-
ing spindle profile will line up with intended
profile area on copy. Slide tail center so it
just touches master spindle and secure it.
Then hold master spindle and tighten hand
knob located on tail center.
Master Spindle or Template
Stylus
5. Adjust crossfeed handwheel until stylus
comes in contact with template in its desired
position.
Move from high points towards
areas with greater depth of cut
Figure 17. Recommended direction of stylus
travel.
-17-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Move carriage stylus to left hand limit of pro-
filed area and adjust left hand carriage stop
until it contacts carriage, then tighten stop
(see Figure 19).
12. Turn lathe OFF and inspect results.
—If workpiece is tapered, copy attachment
is not properly aligned to wood lathe (refer
to Performing Final Alignment on Page
13).
13. If you are satisfied, continue to remove mate-
rial from workpiece, using “downhill” cutting
method illustrated in Figure 17 on Page 17.
Tip: Avoid cutting “uphill”. It will likely result in
chipping and gouging.
14. Continue removing stock until workpiece is
complete (see Figure 20).
Carriage
Stop
Figure 19. Adjusting carriage stops.
7. Repeat procedure for right hand stop.
8. Adjust cutting tool so both it and stylus are
just touching workpiece and template.
—It is essential for accurate copying that
cutting tool tip and stylus always remain at
same positions in relation to workpiece and
template.
9. Slide carriage away from workpiece, so sty-
lus and cutter are clear of workpiece and
template.
Figure 20. Shaping the copy spindle.
15. After completing initial copy, continue follow-
ing Steps 1–14 until all spindles are com-
pleted.
10. Turn lathe ON at its slowest speed, then
slowly advance cutting tool toward left edge
of workpiece. Once contact is made, advance
cutting tool into copy spindle approximately
1⁄16". Turn longitudinal handwheel so the car-
riage travels from left to right.
16. When all spindles are complete, remove copy
attachment and replace it with the lathe tool
post.
17. Use appropriate lathe chisels to sharpen
details and smooth turned surfaces of each
copy, then sand smooth.
11. After each pass, extend cutting tool another
1⁄16" (maximum), and repeat with another
pass. Repeat this process until stylus comes
in contact with template.
—If cutting tool tends to bite or gouge
workpiece, back off cutting tool slightly and
try again. Be conservative when removing
stock.
Refer to your owner's manual for complete
setup, operating, and safety instructions.
Serious injury could occur if you do not fol-
low these instructions.
-18-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
SECTION 4: ACCESSORIES
Recommended Metal Protectants
G5562—SLIPIT® 1 Qt. Gel
G5563—SLIPIT® 12 oz. Spray
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
G2871—Boeshield® T-9 12 oz. Spray
G2870—Boeshield® T-9 4 oz. Spray
H3788—G96® Gun Treatment 12 oz. Spray
H3789—G96® Gun Treatment 4.5 oz. Spray
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
Basic Eye Protection
T20501—Face Shield Crown Protector 4"
T20502—Face Shield Crown Protector 7"
T20503—Face Shield Window
T20451—“Kirova” Clear Safety Glasses
T20452—“Kirova” Anti-Reflective S. Glasses
H7194—Bifocal Safety Glasses 1.5
H7195—Bifocal Safety Glasses 2.0
H7196—Bifocal Safety Glasses 2.5
Figure 22 Recommended products for protect-
ing unpainted cast iron/steel part on machinery.
.
D3098—Center Finder
Find the center of round or square stock for lathe
turning with this handy Center Finder. One side
locates a diagonal line on square stock up to 8"
x 8" and the other side locates a diagonal line on
round stock up to 41⁄2" in diameter.
T20502
T20452
T20503
H7194
T20451
Figure 21. Assortment of basic eye protection.
Figure 23. D3098 Center Finder.
-19-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: MAINTENANCE
Lubrication
To reduce risk of shock or
accidental startup, always
Leadscrews and Slides
disconnect machine from
Lubrication Type ...T23964 or NLGI#2 Equivalent
Amount ..............................................1–2 Pumps
Lubrication Frequency.....................6–12 Months
power before adjustments,
maintenance, or service.
Add lubrication to the leadscrews and slides
shown in Figure 24.
Schedule
For optimum performance from your machine,
follow this maintenance schedule and refer to any
Leadscrews
specific instructions given in this section.
Daily Check
•
•
•
Loose mounting bolts.
Worn or damaged wires.
Any other unsafe condition.
Monthly Check
•
feed cable tension, damage, or wear.
•
Clean/vacuum dust buildup.
Slides
Figure 24. Location of leadscrews and slides.
Cleaning &
Protecting
Cleaning the Model T27313 is relatively easy.
Vacuum excess wood chips and sawdust, and
wipe off the remaining dust with a dry cloth. If any
resin has built up, use a resin dissolving cleaner
to remove it.
Protect any unpainted cast iron surfaces by wip-
ing it clean after every use—this ensures moisture
from wood dust does not remain on bare metal
surfaces. Keep cast iron surfaces rust-free with
regular applications of products like G96® Gun
Treatment, SLIPIT®, or Boeshield® T-9 (see Page
19 for more details).
-20-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: SERVICE
Review the troubleshooting and procedures in this section if a problem develops with your machine. If you
need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.
Note: Please gather the serial number and manufacture date of your machine before calling.
Troubleshooting
Symptom
Possible Cause
Possible Solution
Bad surface finish.
1. Spindle speed or feed rate is wrong.
2. Dull cutting tool.
1. Adjust for appropriate spindle speed and feed rate.
2. Sharpen cutting tool.
3. Too much play in gibs.
3. Tighten gibs (Page 1).
Cutting tool vibrates 1. Cutting tool is not tight enough.
1. Tighten cutting tool.
2. Adjust cutting tool.
excessively during
cutting.
2. Cutting tool sticks too far out of tool arbor;
lack of support.
3. Gibs are out of adjustment.
4. Cutting tool is dull.
3. Adjust gibs (Page 1).
4. Replace or resharpen cutting tool.
5. Use recommended spindle speed.
5. Spindle speed is wrong.
Workpiece is
tapered.
1. Lathe bed and copy attachment are not
parallel with each other.
1. Re-align lathe bed and copy attachment (Page 13).
2. Lathe bed is twisted.
2. Level lathe.
Carriage will not feed 1. Longitudinal-feed handle screw is loose.
1. Tighten screw.
or is hard to move.
2. Chips have loaded up on rails.
2. Frequently clean away chips that load up during
turning operations.
3. Slides are dry and in need of lubrication.
4. Gibs are too tight.
3. Lubricate slides.
4. Loosen gib screw(s) slightly (Page 1).
-21-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Tension
Gib Adjustment
The movement of the carriage assembly along
the body of the copy attachment is controlled by
the movement of the longitudinal-feed handwheel.
This handwheel is connected to the carriage via a
cable. This cable should be taut to ensure respon-
sive movement from the carriage.
The goal of gib adjustment is to remove sloppi-
ness or "play" between the carriage and the bed
while still allowing free movement of the carriage.
There are eight adjustment locations: two on the
front of the carriage, two on the back and four
underneath.
Tools Needed
Open-End Wrench 13mm.................................. 2
Qty
Tools Needed
Qty
Hex Wrench 2.5mm........................................... 1
To adjust cable tension:
Open-Ended Wrench 8mm ............................... 1
1. DISCONNECT MACHINE FROM POWER!
2. Loosen hex nut shown in Figure 25.
To adjust gibs:
1. DISCONNECT MACHINE FROM POWER!
2. Loosen hex nut shown in Figure 26.
3. Adjust tension by loosening or tightening
cable tension bolt (see Figure 25).
3. Adjust set screws to increase or decrease
friction (see Figure 26).
Note: Cable should be pulled snug, but not
so tight that stress is placed on cable.
4. Tighten hex nut (see Figure 25).
Hex Nut
Figure 26. Adjusting carriage gib (1 of 8).
4. Slide carriage back and forth to test for bind-
Cable Tension
Bolt
ing or wobble.
—If carriage binds or wobbles, repeat Step 3.
Figure 25. Adjusting carriage cable tension.
5. When adjustments are complete, tighten the
hex nuts while maintaining the set screw
position.
-22-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: PARTS
Main Breakdown
29
30
28
8
38
52
13
25
15
22
20
21
34
19
18
13-1
25-1
36
35
32
47
16
17
43
42
31
8
38
7
15
46
33
41
25
14
13
24
40
47
48
44
10
8
50
38
9
7
45
49
15
5
11
4
30
6
3
54
2
1
53
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-23-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PT27313001
KNOB M8-1.25
28
29
30
31
32
33
34
35
36
38
40
41
42
43
44
45
46
47
48
49
50
52
53
54
PT27313028
PT27313029
PT27313030
PT27313031
PT27313032
PT27313033
PT27313034
PT27313035
PT27313036
PT27313038
PT27313040
PT27313041
PT27313042
PT27313043
PT27313044
PT27313045
PT27313046
PT27313047
PT27313048
PT27313049
PT27313050
PT27313052
PT27313053
PT27313054
PULLEY SHAFT
2
PT27313002
PT27313003
PT27313004
PT27313005
PT27313006
PT27313007
PT27313008
PT27313009
PT27313010
PT27313011
PT27313013
SUPPORT ARM CLAMPING PLATE
CARRIAGE BOLT M8-1.25 X 150
SUPPORT ARM CLAMP
SUPPORT ARM (TALL)
T-BOLT M10-1.5 X 100
FENDER WASHER 8MM
HEX NUT M8-1.25
PULLEY BRACKET
3
LOCK WASHER 6MM
4
LIVE CENTER
5
LIVE CENTER SLEEVE
EXT RETAINING RING 24MM
KNOB BOLT M12-1.75 X 90
SET SCREW M5-.8 X 4
PHLP HD SCR M8-1.25 X 12
LOCK WASHER 8MM
6
7
8
9
HEX BOLT M6-1 X 25
10
11
13
HEX NUT M6-1
LONGITUDINAL FEED BRACKET
REAR GUIDE RAIL
TEMPLATE SUPPORT BRACKET
TEMPLATE SUPPORT OFFSET
TEMPLATE SUPPORT CLAMPING PLATE
HEX BOLT M8-1.25 X 60
DEAD CENTER
13-1 PT27313013-1 REAR GUIDE RAIL (SHORT)
14
15
16
17
18
19
20
21
22
24
25
PT27313014
PT27313015
PT27313016
PT27313017
PT27313018
PT27313019
PT27313020
PT27313021
PT27313022
PT27313024
PT27313025
CARRIAGE STOP
PHLP HD SCR M6-1 X 12
SET SCREW M5-.8 X 8
HEX NUT M5-.8
CENTER BRACKET
CAP SCREW M6-1 X 85
CENTER CLAMPING PLATE
HEX BOLT M8-1.25 X 25
SUPPORT ARM (SHORT)
T-BOLT M10-1.5 X 45
CARRIAGE GIB (SMALL)
CARRIAGE GIB (LARGE)
HEX BOLT M6-1 X 10
FLAT WASHER 6MM
CHIP GUARD
LONGITUDINAL FEED PULLEY
HEX NUT M10-1.5
COPY ATTACHMENT BED
FRONT GUIDE RAIL
FENDER WASHER 10MM
25-1 PT27313025-1 FRONT GUIDE RAIL (SHORT)
-24-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Longitudinal Drive Breakdown
124
123
122
121
129
130
131
125
126
127
128
132
133
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
121 PT27313121 EXT RETAINING RING 19MM
122 PT27313122 LONGITUDINAL FEED PULLEY
123 PT27313123 SET SCREW M8-1.25 X 16
124 PT27313124 LONGITUDINAL FEED CABLE
125 PT27313125 BUSHING (COPPER)
128 PT27313128 KEY 4 X 4 X 10
129 PT27313129 HANDWHEEL 160MM DIA DISHED (PLASTIC)
130 PT27313130 FLAT WASHER 6MM
131 PT27313131 CAP SCREW M6-1 X 12
132 PT27313132 HANDWHEEL HANDLE
133 PT27313133 FLAT HD SCR M6-1 X 8
126 PT27313126 LONGITUDINAL SPINDLE SLEEVE
127 PT27313127 LONGITUDINAL FEED SPINDLE
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
-25-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
Carriage Breakdown
231
233 234
232
236
235
237
258
255
244
239
240
254
253
251
257
238
252
247
242
247
243
241
244
250
246
245
248
249
256
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
231 PT27313231 SET SCREW M8-1.25 X 16
232 PT27313232 CUTTING TOOL ARBOR
233 PT27313233 QUILL
245 PT27313245 STYLUS
246 PT27313246 EXTENSION SPRING
247 PT27313247 HEX NUT M8-1.25
248 PT27313248 VENTED BOLT M8-1.25 X 65
249 PT27313249 MOUNTING PLATE
250 PT27313250 CAP SCREW M6-1 X 12
251 PT27313251 HEX BOLT M8-1.25 X 16
252 PT27313252 BUSHING (COPPER)
253 PT27313253 CARRIAGE CASTING
254 PT27313254 SET SCREW M5-.8 X 12
255 PT27313255 CUTTING TOOL
234 PT27313234 GAUGE ROD
235 PT27313235 INDICATOR PLATE
236 PT27313236 LOCK WASHER 5MM
237 PT27313237 PHLP HD SCR M5-.8 X 12
238 PT27313238 CARRIAGE SPACER
239 PT27313239 LEADSCREW SEAT
240 PT27313240 CAP SCREW M6-1 X 30
241 PT27313241 LEADSCREW
242 PT27313242 SET SCREW M8-1.25 X 12
243 PT27313243 HANDWHEEL HANDLE
244 PT27313244 SET SCREW M5-.8 X 10
256 PT27313256 HANDWHEEL 98MM DIA DISHED (PLASTIC)
257 PT27313257 FLAT HD SCR M6-1 X 8
258 PT27313258 MACHINE ID LABEL
-26-
Model T27313 (Mfd. Since 01/15)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email _________________________________________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Woodwork
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Shotgun News
____ Today’s Homeowner
____ Wood
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
____ 6-9
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY & RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|