MODEL T25920/T25926
VARIABLE-SPEED WOOD
LATHE
OWNER'S MANUAL
(For models manufactured since 08/14)
T25920
T25926
COPYRIGHT © DECEMBER, 2014 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#AWWK17009 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Manual Accuracy
Contact Info
We are proud to provide a high-quality owner’s
manual with your new machine!
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
We made every effort to be exact with the instruc-
tions, specifications, drawings, and photographs
contained inside. Sometimes we make mistakes,
but our policy of continuous improvement also
means that sometimes the machine you receive
will be slightly different than what is shown in
the manual.
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Email: techsupport@grizzly.com
If you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure, check our website
for an updated version. We post current manuals
and manual updates for free on our website at
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Alternatively, you can call our Technical Support
for help. Before calling, please write down the
Manufacture Date and Serial Number stamped
into the machine ID label (see below). This infor-
mation helps us determine if updated documenta-
tion is available for your machine.
Bellingham, WA 98227-2069
Email: manuals@grizzly.com
Manufacture Date
Serial Number
-3-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
T25920 & T25926 Data Sheet
MODELS 5920 & T25926
BENCHTOP LATHES
Model Number
Product Dimensions
Weight
T25920
T25926
84 lbs.
383⁄4 x 12 X 17 in.
30 x 8 in.
75 lbs.
373⁄4 x 12 x 13 in.
30 x 8 in.
Width (side-to-side) x Depth
(front-to-back) x Height
Footprint (length x width)
Shipping Dimensions
Type
Cardboard
Machine
Content
Weight
89 lbs.
79 lbs.
Width (side-to-side) x Depth
(front-to-back) x Height
32 x 19 x 12 in.
33 x 17 x 13 in.
Must Ship Upright
Electrical
Yes
Power Requirement
Prewired Voltage
Full-Load Current Rating
Minimum Circuit Size
Connection Type
Power Cord Included
Switch
110V, Single-Phase, 60 Hz
110V
5.3A
6A
15A
Cord & Plug
Yes
Toggle Switch w/Disabling Key
Cord Length
6 ft.
18 AWG
Yes
Cord Gauge
Plug Included
Included Plug Type
NEMA 5-15
Motor
Type
Universal Brush-Type Motor
Horsepower
Phase
550W (3⁄4 HP)
5.3A
370W (1⁄2 HP)
Single-Phase
Amps
6A
Speed
1700 RPM
Bearings
Power Transfer
Shielded & Permanently Sealed
V-Belt
-4-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Number
Operation Information
Swing Over Bed
T25920
12 in.
T25926
93⁄4 in.
93⁄4 in.
12 in.
Dist. Between Centers
Bed Width
161⁄2 in.
163⁄4 in.
71⁄4 in.
31⁄8 in.
Faceplate Size
Swing Over Tool Rest Base
No. Of Spindle Speeds
Spindle Speed Range
Spindle Information
Spindle Taper
91⁄2 in.
71⁄4 in.
Variable
650 – 3800 RPM
MT#2
1 in.
Spindle Thread Size
Spindle TPI
8 TPI
Spindle Thread Direction
Spindle Bore
Right Hand
Through-Hole 11⁄16 in.
Spur
Type of Included Spindle Center
Tailstock Information
Tailstock Taper
MT#2
Live
Tailstock Center Type
Tool Rest Information
Tool Rest Width
57⁄8 in.
53⁄4 in.
5
Tool Rest Post Diameter
Tool Rest Post Length
Tool Rest Base Height
⁄
8
in.
3 in.
11⁄4 in.
23⁄8 in.
13⁄8 in.
Construction
Headstock
Bed
Cast Iron
Cast Iron
Cast Iron
Cast Iron
Cast Iron
Urethane
Frame
Base
Tailstock
Paint
Other
Country of Origin
Warranty
China
1 Year
Serial Number Location
ISO 9001 Factory
Assembly Time
ID Label
Yes
10 Minutes
-5-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
Become familiar with names and locations of controls and features shown below to better understand
instructions in this manual.
F
A
C
G
B
D
O
E
N
H
I
J
M
L
K
Figure 1. T25920/T25926 control and component identification.
I. Tool Rest Lock Lever
J. Base Lock Lever
A. Headstock
B. Faceplate
K. Belt Tension Lever
L. Lathe ON/OFF Switch
M. Spindle Speed Dial
N. Headstock Handwheel
O. Digital Readout
C. Tool Rest
D. Live Center
E. Tailstock Lock Lever
F. Quill Lock Lever
G. Quill Handwheel
H. Tailstock
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
-6-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Tool Rest: Provides a stable resting position for
turning tools.
Controls &
Components
Tool Rest Lock Lever: Locks tool rest in position
relative to tool rest base.
Base Lock Lever: Lock and unlocks tool rest
base and allows it to be repositioned along lathe
bed.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
Tool Rest
Tool Rest
Lock Lever
Use descriptions and figures below to become
familiar with basic controls of your lathe.
ON/OFF Switch: Turns power ON/OFF to lathe
motor, which rotates spindle.
Belt Tension Lever: Releases tension on belt to
change speeds or replace belt.
Base Lock
Lever
Spindle Speed Dial: Adjusts speed of the spindle
within current belt position speed range.
Figure 4. Tool rest control levers.
Quill Handwheel: Moves quill in and out to allow
clamping or releasing of workpiece.
Spindle
Speed Dial
Quill Lock Lever: Locks quill in place to prevent
loosening during operation of lathe.
Tailstock Lock Lever: Unlocks tailstock to allow
quick position adjustments.
ON/OFF
Switch
Belt Tension Lever
Quill Handwheel
Figure 2. Tension lever and ON/OFF switch.
RPM Display: Displays spindle speed in revolu-
tions per minute (RPM).
Quill Lock Lever
Tailstock Lock
Lever
RPM Display
Figure 5. Typical tailstock controls.
Figure 3. RPM display on headstock.
-7-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand this ELECTRICAL EQUIPMENT INJURY RISKS. You
owner’s manual BEFORE using machine.
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
TRAINED OPERATORS ONLY. Untrained oper-
ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
DISCONNECT POWER FIRST. Always discon-
nect machine from power supply BEFORE making
adjustments, changingtooling, orservicingmachine.
This prevents an injury risk from unintended startup
or contact with live electrical components.
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-8-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
WEARING PROPER APPAREL. Do not wear FORCING MACHINERY. Do not force machine.
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work-
piece control.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a NIOSH-approved respirator to
reduce your risk.
STABLE MACHINE. Unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. Using improper acces-
sories will increase the risk of serious injury.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica-
tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect safe
operation. Immediately repair or replace damaged
or mis-adjusted parts before operating machine.
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.
-9-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety for Wood Lathes
MAIN INJURY HAZARDS: Death or crushing injury from getting entangled in rotating spindle
or workpiece; death, blindness, or broken bones from being struck by a workpiece that breaks
apart or comes loose during rotation, turning tool kickback, or flying wood chips. To minimize
your risk of these hazards, always heed the following warning information:
INTEGRITY OF STOCK. Verify each workpiece EYE/FACE PROTECTION. Always wear a face
is free of knots, splits, nails, or foreign material shield and safety glasses when operating lathe.
to ensure it can safely rotate on spindle without
breaking apart or causing turning tool kickback.
PROPER APPAREL. Do not wear gloves, necktie
or loose clothing. Keep keep long hair away from
WORKPIECE PREPARATION. Before mounting, rotating spindle.
cut off waste portions with a bandsaw or other tool
to ensure workpiece has no large edges to catch SPEED RATES. Select correct spindle speed for
turning tool, and it will rotate without dangerous workpiece size, type, shape, and condition. Use
wobbling.
low speeds when roughing or when turning large,
long, or non-concentric workpieces. Allow spindle
SECURING LOCKS. Verify tool rest, headstock, to reach full speed before turning.
and tailstock are secure before turning lathe ON.
NEW SETUPS. Test each new setup by starting
SECURING WORKPIECE. An improperly secured spindle rotation at the lowest speed and standing
workpiece can fly off spindle with deadly force. to the side of the lathe until workpiece reaches full
Use proven setup techniques and always verify speed and you can verify safe rotation.
workpiece is well-secured before starting lathe.
Only use high-quality fasteners with non-tapered ROUGHING. Use correct tool. Take light cuts,
heads for faceplate attachment.
use low speeds, and firmly support tool with both
hands.
TOOL SUPPORT. An improperly supported tool
may be grabbed or ejected. Adjust tool rest SHARP TOOLS. Only use sharp turning tools—
1
1
approximately ⁄4" away from workpiece and ⁄8
"
they cut with less resistance than dull tools. Dull
above workpiece center line to provide proper turning tools can catch or grab and pull your
support for turning tool. Firmly hold turning tool hands into the rotating workpiece.
with both hands against tool rest.
STOPPING SPINDLE. Always allow spindle to
TOOL KICKBACK. Occurs when turning tool is completely stop on its own. Never put hands or
ejected from workpiece with great force, striking another object on spinning workpiece.
operator or bystanders. Commonly caused by
poor workpiece selection/preparation, improper ADJUSTMENTS/MAINTENANCE. Make sure
tool usage, or improper machine setup or tool rest wood lathe is turned OFF, disconnected from
adjustment.
power, andallmovingparts are completely stopped
before doing adjustments or maintenance.
ADJUSTMENT TOOLS. Remove all chuck keys,
wrenches, and adjustment tools before turning MEASURING WORKPIECE. Only measure work-
lathe ON. A tool left on the lathe can become a piece after it has stopped. Trying to measure a
deadly projectile when spindle is started.
spinning workpiece increases entanglement risk.
SAFE CLEARANCES. Before starting spindle, SANDING/POLISHING. To reduce entanglement
verify workpiece has adequate clearance by hand- risk, remove tool rest before sanding. Never com-
rotating it through its entire range of motion.
pletely wrap sandpaper around workpiece.
-10-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: POWER SUPPLY
Availability
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
110V Circuit Requirements
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
Nominal Voltage ........................................ 110V
Cycle..........................................................60 Hz
Phase........................................... Single-Phase
Power Supply Circuit ......................... 15 Amps
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
T25920 Full-Load Current Rating .............5.3A
T25926 Full-Load Current Rating .............6.0A
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, con-
sult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
-11-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding & Plug Requirements
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
This machine is equipped with a power cord that
has an equipment-grounding wire and a grounding
plug. Only insert plug into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
DO NOT modify the provided plug!
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
GROUNDED
5-15 RECEPTACLE
Extension Cords
Grounding Prong
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
5-15 PLUG
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Neutral Hot
Figure 6. Typical 5-15 plug and receptacle.
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
Minimum Gauge Size...........................14 AWG
Maximum Length (Shorter is Better).......50 ft.
SHOCK HAZARD!
Two-prong outlets do not meet the grounding
requirements for this machine. Do not modify
or use an adapter on the plug provided—if
it will not fit the outlet, have a qualified
electrician install the proper outlet with a
verified ground.
-12-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: SETUP
Unpacking
Needed for Setup
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at (570) 546-9663 for advice.
The following are needed to complete the setup
process, but are not included with your machine.
Description
Qty
•
•
•
•
•
•
•
Additional People ....................................... 1
Safety Glasses ........................................... 1
Cleaner/Degreaser ..................... As Needed
Disposable Shop Rags............... As Needed
Phillips Head Screwdriver #2 ..................... 1
Leather Gloves ........................................... 1
Flathead Screwdriver.................................. 1
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
Model T25920/T25926 is
a heavy machine. DO
NOT over-exert yourself
while unpacking or mov-
ing your machine—get
assistance.
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
Wear safety glasses during
the entire setup process!
-13-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Inventory
Cleanup
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
Box 1 (Figure 3)
Qty
A. Knockout Rod............................................. 1
B. Hex Wrench 8mm....................................... 1
C. Hex Wrench 6mm....................................... 1
D. Hex Wrench 3mm....................................... 1
E. Handwheel Handle..................................... 1
F. Spur Center................................................ 1
G. Live Center ................................................. 1
There are many ways to remove this rust preven-
tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-
turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
Before cleaning, gather the following:
•
•
•
•
Disposable rags
A
Cleaner/degreaser (WD•40 works well)
Safety glasses & disposable gloves
Plastic paint scraper (optional)
B
G
Basic steps for removing rust preventative:
1. Put on safety glasses.
C
D
2. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
E
F
3. Wipe off the surfaces. If your cleaner/degreas-
er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
Figure 7. Inventory components.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
4. Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces.
-14-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Site Considerations
Bench Mounting
The base of this machine has mounting holes
that allow it to be fastened to a workbench or
other mounting surface to prevent it from moving
during operation and causing accidental injury or
damage.
Workbench Load
Refer to the Machine Data Sheet for the weight
and footprint specifications of your machine.
Some workbenches may require additional rein-
forcement to support the weight of the machine
and workpiece materials.
The strongest mounting option is a "Through
Mount" (see example below) where holes are
drilled all the way through the workbench—and
hex bolts, washers, and hex nuts are used to
secure the machine in place. The rubber feet
on the bottom of the base must be removed to
"Through Mount" the lathe.
Placement Location
Consider anticipated workpiece sizes and addi-
tional space needed for auxiliary stands, work
tables, or other machinery when establishing a
location for this machine in the shop. Below is
the minimum amount of space needed for the
machine.
Hex
Bolt
383⁄4
"
Flat Washer
17
Machine Base
Workbench
Flat Washer
Lock Washer
Hex Nut
Figure 8. T25920 minimum working clearances.
Figure 10. "Through Mount" setup.
373⁄4
"
Another option is a "Direct Mount" (see example
below) where the machine is secured directly to
the workbench with lag screws and washers.
173⁄4
"
Lag Screw
Figure 9. T25926 minimum working clearances.
Flat Washer
Children and visitors may be
seriously injured if unsuper-
vised around this machine.
Lock entrances to the shop
or disable start switch or
power connection to prevent
unsupervised use.
Machine Base
Workbench
Figure 11. "Direct Mount" setup.
-15-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Serious injury or death can result from
using this machine BEFORE understanding
its controls and related safety information.
DO NOT operate, or allow others to operate,
machine until the information is understood.
Assembly consists of installing the electrical box
onto the base with two pre-installed Phillips head
screws, then installing the handwheel handle onto
the tailstock quill with the pre-installed flathead
screw.
To assemble machine:
DO NOT start machine until all preceding
setup instructions have been performed.
Operating an improperly set up machine
may result in malfunction or unexpect-
ed results that can lead to serious injury,
death, or machine/property damage.
1. Use (2) pre-installed Phillips head screws
and (2) flat washers to attach electrical box
to lathe, as shown in Figure 12.
Electrical Box
To test run machine:
1. Clear all setup tools away from machine.
2. Connect machine to power supply.
3. Turn machine ON, verify motor operation,
and then turn machine OFF.
x2
The motor should run smoothly and without
unusual problems or noises.
Figure 12. Electrical box installed.
4. Remove key from toggle switch, as shown
2. Insert handwheel handle into quill handwheel
below.
and tighten with flathead screwdriver.
3. To insert centers, refer to Installing/
RemovingHeadstockCenterandInstalling/
Removing Tailstock Center on Page 22.
Test Run
Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning properly.
Figure 13. Removing key from toggle switch.
5. Try to start machine.
If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The Troubleshooting table in the
SERVICE section of this manual can help.
—Machine should NOT start. If it does start,
switch disabling feature is not functioning
properly and switch must be replaced.
-16-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATIONS
The purpose of this overview is to provide the nov-
To complete a typical operation, the operator
does the following:
ice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
1. Examines workpiece to make sure it is suit-
able for turning. No extreme bows, knots, or
cracks should exist.
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual and seek additional training from expe-
rienced machine operators, and do additional
research outside of this manual by reading "how-
to" books, trade magazines, or websites.
2. Prepares and trims workpiece to make it
roughly concentric.
3. Installs workpiece between centers, or attach-
es it to faceplate or chuck.
4. Adjusts tool rest to 1⁄8" above workpiece cen-
terline, and sets minimum clearance between
the workpiece and lip of tool rest to 1⁄4".
Eye injuries or respiratory problems can
occur while operating this tool. Wear per-
sonal protective equipment to reduce your
risk from these hazards.
5. Rotates workpiece by hand to verify that the
spindle and workpiece rotate freely through-
out the range of motion.
6. Positions dust collection hood near work
piece to collect wood chips secure in place.
7. Ties back loose hair and clothing, and puts
on face shield and respirator. Takes all other
required safety precautions.
8. Starts lathe, adjusts lathe speed, and care-
fully begins turning operation, keeping chisel
against tool rest entire time it is cutting.
Keep hair, clothing, and
jewelry away from mov-
ing parts at all times.
Entanglement can result
in death, amputation, or
severe crushing injuries!
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj-
ects. Regardless of the content in this sec-
tion, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
-17-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Large/Loose Knots:
Stock Inspection &
Requirements
Loose knots can become dislodged during
the turning operation. Large knots can cause
a workpiece to completely break in half dur-
ing turning and cause machine damage and
personal injury. Choose workpieces that do
not have large/loose knots.
Some workpieces are not safe to turn or may
require modification before they are safe to
turn. Before turning a workpiece, inspect all
workpieces for the following:
•
Wet or "Green" Stock:
Cutting wood with a moisture content over
20% causes unnecessary wear on tooling
blades, increases the risk of tool grab, and
yields poor results.
•
Workpiece Type:
This machine is intended for cutting natural
and man-made wood products, and some
plastics. Never attempt to cut any metal,
stone, or rubber workpiece; cutting these
materials can lead to machine damage or
severe injury.
•
Excessive Warping:
Workpieces with excessive bowing or twist-
ing are unstable and unbalanced. Never turn
these workpieces at high speed, or instability
will be magnified and the workpiece can be
ejected from the lathe causing impact injures.
Only turn concentric workpieces!
•
Foreign Objects:
Nails, staples, dirt, rocks and other foreign
objects are often embedded in wood. While
cutting, these objects can become dislodged
and hit the operator, cause tool grab, or break
the turning tool, which might then fly apart.
Always visually inspect your workpiece for
these items. If they can't be removed, DO
NOT turn the workpiece.
-18-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Spindle
Speeds
Always choose correct spindle speed for
your operation. Using wrong speed may lead
to workpiece breaking loose or being thrown
from lathe at a high rate of speed, causing
fatal or severe impact injuries.
Your lathe has three speed ranges for maximum
turning options. These ranges are selected by
changing belt positions on the motor and spindle
pulleys (see Figure 14).
Tool Needed:
Hex Wrench 6mm.............................................. 1
= High Range
1600–3800 RPM
A
To change speeds:
Spindle
B = Mid Range
1250–2800 RPM
1. DISCONNECT MACHINE FROM POWER!
A
= Low Range
650–1450 RPM
C
2. Loosen belt tension screw (see Figure 16).
Be sure belt tension lever moves freely to
release tension from belt.
B
C
Motor
(Viewed from Back of Headstock)
Figure 14. Speed ranges for each belt position.
High range (A) is best when turning a workpiece
where a clean finish is required and only light
cuts are made. Mid range (B) is a compromise
between the high and low ranges. Low range
(C), which has more torque, is best when turn-
ing a workpiece where a lot of material must be
removed and a rough finish does not matter. Use
the speed dial to adjust the spindle speed within
each range.
Belt Tension Screw
Belt Tension Lever
Figure 16. Belt tension lever.
3. Open side access cover and remove rear
access cover (see Figure 17).
Refer to the speed recommendations chart in
Figure 15 to choose the appropriate RPM for your
operation. Then choose the speed range that will
include the selected RPM.
Speed
Chart
Diameter Roughing General Finishing
of Work-
piece
RPM
Cutting
RPM
RPM
Under 2"
2–4"
1520
760
510
380
300
255
3000
1600
1080
810
3000
2480
1650
1240
1000
830
Side Access
Cover Opened
4–6"
Rear Access Cover
6–8"
Removed
8–10"
10–12"
650
540
Figure 17. Side and rear access covers.
Figure 15. Speed recommendations.
-19-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Locate desired speed on speed chart on
top of control box (see Figure 15 on Page
19) and move belt to necessary grooves
on motor and spindle pulleys, as shown in
Figure 18.
Adjusting Tailstock
The tailstock is equipped with a cam-action
clamping system to secure it to the lathe bed.
When the lock lever is engaged, a plate lifts and
secures the tailstock to the bed.
= High Range
A
1600–3800 RPM
Tool Needed:
Spindle
B = Mid Range
1250–2800 RPM
Wrench 12mm ................................................... 1
A
To position tailstock along bed:
= Low Range
650–1450 RPM
C
B
C
1. Disengage lock lever and move tailstock to
desired position (see Figure 20).
Motor
(Viewed from Back of Headstock)
Figure 18. Speed ranges for each belt position.
Lock Lever
Lathe Bed
5. Move belt tension lever down to tension belt,
then tighten belt tension lever screw.
Note: When properly tensioned, the belt
1
should deflect about ⁄2" when moderate
pressure is applied to the belt mid-way
between upper and lower pulleys, as shown in
Figure 19.
Figure 20. Typical tailstock lock lever to adjust
tailstock position.
2. Re-engage lock lever.
— If lock lever will not lock or unlock, then
adjust tailstock base mounting nut (locat-
ed on underside of tailstock base) in small
increments to achieve proper clamping
pressure (see Figure 21).
Pulley
1
⁄2
"
Deflection
Pulley
Figure 19. Checking belt deflection.
6. After verifying belt tension is correct, re-install
Tailstock Mounting Nut
rear cover and close side access cover.
Figure 21. Mounting nut location.
-20-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Tool Rest
Always operate the lathe with the tool
rest assembly firmly locked in position.
Otherwise, serious personal injury may
occur by the tool being pulled from the
operator's hands.
The tool rest base is equipped with a cam-action
clamping system to secure it to the lathe bed.
When the lever is engaged, a locking plate lifts up
and secures the tool rest base to the bed.
Adjusting Angle or Height
Positioning Along Bed
1. Loosen the tool rest base lock lever and the
tool rest lock lever to adjust the position of the
tool rest.
1. Disengage base lock lever and slide tool rest
base along bed (see Figure 22).
1
2. Position the tool rest approximately ⁄4" away
Tool Rest
Tool Rest
1
from the workpiece and approximately ⁄8
above the workpiece center line, as shown in
"
Lock Lever
Base
Figure 23.
Lathe
Bed
1⁄4"
Workpiece
Distances
1⁄8"
Center Line
Base Lock
Lever
Figure 22. Typical tool rest controls to adjust
position and height.
Tool Rest
2. Re-engage the tool rest base lock lever to
secure the tool rest assembly in position.
Figure 23. Tool rest position relative to
workpiece.
Note: The large clamping hex nut under-
neath the tool rest base will require occa-
sional adjusting to ensure proper clamping
pressure of the tool rest assembly to the bed.
Turn this hex nut in small increments to fine
tune the clamping pressure as needed.
3. Re-tighten the tool rest lock lever and the tool
rest base lock lever to secure the tool rest in
position.
-21-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing Headstock Center
Installing/Removing
Headstock Center
1. DISCONNECT MACHINE FROM POWER!
2. Insert knockout rod into outboard end of
spindle. Use a shop rag or wear a glove to
catch center and gently tap rod handle until
spur center is freed from spindle (see Figure
25).
The spur center installs in the headstock spindle
with an MT#2 taper fit.
Tools Needed:
Gloves ............................................................... 1
Knockout Rod.................................................... 1
Knockout Rod
Installing Headstock Center
1. DISCONNECT MACHINE FROM POWER!
2. Make sure surface of center and spindle are
free of debris and oily substances before
inserting center.
Spur Center
3. Insert tapered end of center into spindle, and
push it in quickly and firmly (see Figure 24).
Figure 25. Typical spur center removal from
headstock spindle.
Spur center is sharp and may cause cuts.
Wear gloves when installing spur center.
Installing/Removing
Tailstock Center
The included live center installs into the tailstock
with an MT#2 tapered fit.
Installing Live Center in Tailstock
1. Loosen quill lock handle (if locked) approxi-
mately half a turn.
2. Rotate quill handwheel clockwise until quill
protrudes about 3⁄4".
Spur Center
Figure 24. Typical installation of spur center into
headstock.
4. Check that center is securely installed by giv-
ing it a quick tug. (A properly installed center
will not pull out by hand.)
-22-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Insert live center, as shown in Figure 26,
Removing/Installing
Faceplate
and push firmly.
Quill Lock Lever
These instructions cover removing and installing
the faceplate. To mount a workpiece to your face-
plate, refer to Faceplate Turning on Page 27.
Removing Faceplate
1. DISCONNECT MACHINE FROM POWER!
Quill
Quill
Handwheel
2. Hold headstock handwheel securely while
turning faceplate counterclockwise until it is
removed. If the spur center is installed, it will
be removed during this process.
Live Center
Figure 26. Typical live center installation.
4. Tighten quill lock handle.
Faceplate
Removing Live Center from Tailstock
1. Loosen quill lock handle (if locked) approxi-
mately half a turn.
2. Turn quill handwheel counterclockwise until
tailstock quill fully retracts, causing live center
to be forced out of quill.
Headstock
Handwheel
Tailstock quill must always be locked during
lathe operation. Workpiece can be thrown
from lathe if this step is not observed. Also,
tailstock quill should not protrude from
tailstock housing more than 2'' or quill will
not be supported enough. Failure to follow
warnings may result in personal injury.
Figure 27. Typical faceplate removal.
Installing Faceplate
1. DISCONNECT MACHINE FROM POWER!
2. Thread faceplate onto spindle shaft until
secure against shoulder on spindle shaft.
-23-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Scrapers—Typically used where access for
other tools is limited, such as hollowing oper-
ations. This is a flat, double-ground tool that
comes in a variety of profiles (round nose,
spear point, square nose, etc.) to match
many different contours.
Selecting Turning
Tools
Lathe tools come in a variety of shapes and sizes
and usually fall into five major categories.
•
Gouges—Mainly used for rough cutting,
detail cutting, and cove profiles. Rough gouge
is a hollow, double-ground tool with a round
nose, and detail gouge is a hollow, double-
ground tool with either a round or pointed
nose.
Figure 30. Example of a round nose scraper.
•
Parting Tools—Used for sizing and cut-
ting off work. This is a flat tool with a sharp
pointed nose that may be single- or double-
ground.
Figure 28. Example of a gouge.
•
Skew Chisel—A very versatile tool that can
be used for planing, squaring, V-cutting,
beading, and parting off. The skew chisel is
flat, double-ground with one side higher than
the other (usually at an angle of 20-40˚).
Figure 31. Example of a parting tool.
•
Specialty Tools—These are the unique,
special function tools to aid in hollowing, bowl
making, cutting profiles, etc. The Swan Neck
Hollowing Tool shown on Page 30 is a good
example of a specialty tool.
Figure 29. Example of a skew chisel.
-24-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Make center mark by using wood mallet and
tapping point of spur center into center of
workpiece on both ends.
Spindle Turning
Spindle turning is the operation performed when
a workpiece is mounted between the headstock
and the tailstock, as shown in Figure 32.
3. Using 1⁄4" drill bit, drill 1⁄4" deep hole at center
mark on end of workpiece to be mounted on
headstock spur center.
4. To help embed spur center into workpiece,
1
cut ⁄8" deep saw kerfs in headstock end of
workpiece along diagonal lines marked in
Step 1.
5. If your workpiece is over 2" x 2", cut corners
off workpiece lengthwise to make turning
safer and easier (see Figure 34).
Figure 32. Typical spindle turning operation.
Workpiece
Center
Make sure the headstock and tailstock cen-
ters are properly aligned before beginning
any turning operation. Failure to observe
this warning could result in the workpiece
being thrown from the lathe, resulting in
serious personal injury.
Figure 34. Corners of workpiece removed.
6. Drive spur center into end center mark of
To set up a spindle turning operation:
workpiece with wood mallet to embed it at
1
least ⁄4" into workpiece, as shown in Figure
1. Find center point of both ends of your
workpiece by drawing diagonal lines from
corner to corner across end of workpiece, as
shown in Figure 33.
35.
Workpiece
¼"
Pencil Lines
Marked Diagonally
Across Corners
Workpiece
Center
Figure 35. Spur center properly embedded.
Figure 33. Workpiece marked diagonally from
corner to corner to determine the center.
-25-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
7. With workpiece still attached, insert spur cen-
ter into headstock spindle (refer to Installing/
Removing Headstock Center on Page 22
for additional instructions).
Spindle Turning Tips:
•
When turning the lathe ON, stand away from
the path of the spinning workpiece until the
spindle reaches full speed and you can verify
that the workpiece will not come loose.
Note: Use the tool rest to support the oppo-
site end of workpiece so that the workpiece
and spur center do not separate during
installation.
•
•
Use the slowest speed when starting or stop-
ping the lathe.
8. Install live center into tailstock quill and
tighten quill lock lever to lock quill in position
(refer to Page 22 for additional instructions).
Select the right speed for the size of workpiece
that you are turning (refer to Figure 15 on
Page 19).
9. Slide tailstock toward workpiece until point of
live center touches workpiece center mark,
then lock tailstock in this position.
•
•
Keep the turning tool on the tool rest the
ENTIRE time that it is in contact with the
workpiece.
10. Loosen quill lock lever and rotate tailstock
handwheel to push live center into workpiece
at least a 1⁄4".
Learn the correct techniques for each tool
you will use. If you are unsure about how to
use the lathe tools, read books or magazines
about lathe techniques, and seek training
from experienced and knowledgeable lathe
users.
Do not press workpiece too firmly with
tailstock or bearings will bind and over-
heat. Do not adjust tailstock too loosely or
workpiece will spin off lathe. Use good judg-
ment and care, otherwise, serious personal
injury could result from workpiece being
ejected at high speeds.
Eye injuries or respiratory problems can
occur while operating this tool. Wear per-
sonal protective equipment to reduce your
risk from these hazards.
11. Properly adjust tool rest to the workpiece
(see Adjusting Tool Rest on Page 21).
12. Before beginning lathe operation, rotate
workpiece by hand to ensure that there is
safe clearance on all sides.
Keep lathe tool resting on tool rest ENTIRE
time that it is in contact with workpiece or
when preparing to make contact between
lathe tool and workpiece. Otherwise, spin-
ning workpiece could force lathe tool out
of your hands or entangle your hands with
workpiece. Failure to heed this warning
could result in serious personal injury.
-26-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
Faceplate Turning
Only use screws with non-tapered heads
(see Figure 38) to attach the faceplate to
the workpiece. Screws with tapered heads
can split the faceplate or snap off during
operation.
Faceplate turning is when a workpiece is mounted
to the faceplate, which is then mounted to the
headstock spindle, as shown in Figure 36. This
type of turning is usually done with open-faced
workpieces like bowls or plates.
Correct
Incorrect
Figure 38. Correct and incorrect screw types for
mounting workpiece to faceplate.
3. Thread and secure faceplate onto head-
stock spindle (refer to Removing/Installing
Faceplate on Page 23 for faceplate mount-
ing instructions).
Figure 36. Typical faceplate turning operation.
Mounting Workpiece to Faceplate
1. Mark workpiece center in same manner as
described in Spindle Turning (see Page 25).
— If wood screws cannot be placed in the
workpiece, the faceplate can be mount-
ed to a backing block attached to the
workpiece (see Mounting Workpiece to
Backing Block on Page 28).
Note: Cut off corners of workpiece to make it
as close to "round" as possible, as described
in Spindle Turning on Page 25.
2. Center faceplate on workpiece and attach
with wood screws that do not have tapered
heads (see Figure 37).
Figure 37. Typical attachment of faceplate to
workpiece.
-27-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Workpiece to Backing
Block
1. Make backing block from a suitable size
Sanding/Finishing
After the turning operations are complete, the
workpiece can be sanded and finished before
removing it from the lathe, as shown in Figure 39.
piece of scrap wood.
Note: The faces of the backing block must be
flat and parallel to each other, or the uneven
surfaces will cause the workpiece to spin
eccentrically, causing unnecessary vibration
and runout. It is best to mount the backing
block to the faceplate and turn the other sur-
face flat prior to mounting.
2. Locate and mark center of workpiece and
backing block.
1
3. Drill a ⁄4" hole through center of backing
block.
4. Look through hole in backing block to line up
center with workpiece, then glue and clamp
backing block to workpiece.
Figure 39. Typical sanding operation.
Note: Allow the glue to cure according to
manufacturer instructions.
Note: Whenever sanding or finishing, move the
tool rest holder out of the way to increase per-
sonal safety and gain adequate working room.
5. Follow Steps 1–3 in Mounting Workpiece
to Faceplate (see Page 27) to attach back-
ing block to the faceplate.
Sandpaper
Wrapping
sandpa-
per completely around
workpiece could pull
your hands into mov-
ing workpiece and may
cause serious injury.
Never wrap sandpa-
per or finishing materi-
als completely around
workpiece.
Workpiece
-28-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ACCESSORIES
H6542—Robert Sorby HSS 8-PC Turning Set
3
This 8-pc. HSS Turning Tool Set includes ⁄4
"
"
1
1
3
Roughing Gouge, ⁄4" and ⁄2" Spindle Gouge, ⁄8
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
3
3
Bowl Gouge, ⁄4" Standard Skew, ⁄16" Diamond
Side Cut Scraper, 1" Square Scraper, and ⁄2
Round Scraper. Overall lengths are 16" to 19".
1
"
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
T27327—22" Bed Extension
Need a longer lathe but don't want to dedicate the
space to another machine, then add this 22" bed
extension and turn stock up to 38" long.
Figure 42. Model H6542 Robert Sorby 8-PC Set.
T25535—New Turning Wood Book
The appeal of woodturning is simple: with only
a few hand tools and a lathe, remarkable results
can be quickly achieved, including beautiful bowls,
boxes in the round, lamp bases, and furniture
parts. For over 20 years, woodturners have been
turning to Richard Raffan for expert advice and
inspiration.
Figure 40. Model T27327 Bed Extension.
H8049—6" 4-Jaw Wood Chuck 1
Independently adjustable jaws hold odd
shaped work. Jaws can be reversed for differ-
ent holding applications. Includes chuck wrench.
Figure 43. T25535 Turning Wood Book.
Figure 41. Model H8049 4-Jaw Wood Chuck.
-29-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
H5954—Robert Sorby Stebcentre MT#2, 11⁄4
"
T10501—9 Piece Wood Lathe Center Kit
This all-in-one set features a variety of
interchangeable lathe centers for every spindle
turning application. Includes: MT#1 and MT#2
live centers, 3 spur centers, 3 multi-spur centers,
mounting adapter, wrenches and fitted case. Fits
lathes with 1" x 8 TPI RH spindles.
Razor sharp teeth bite into the workpiece for
secure operation and the spring loaded center
point controls the amount of drive or slip. This pat-
ented feature helps avoid the problem of ‘dig-in’.
Production turners can also load and unload their
work while the lathe is still running!
Figure 46. Lathe center kit with fitted case.
Figure 44. Model H5954 MT#2 Stebcentre.
H0507—20" Swan Neck Hollowing Tool
H0508—24" Swan Neck Hollowing Tool
An excellent choice for blind turning or undercut-
ting where reach is restricted. H0507 is designed
for end grain use while H0508 (with a more sub-
stantial steel cross section) is designed for both
end grain and side grain (bowl) use.
T10117—Big Mouth Dust Hood with Stand
Capture dust from any machine operation with
this Big Mouth Dust Hood. Simply attach a 4" dust
collection hose and adjust the hood right where
you need it. The free-standing base eliminates
complicated machine set-ups and the tilting 163⁄8
"
x 127⁄8" hood adjusts from 23" to 43" high. Every
shop needs one of these!
Figure 47. Swan neck hollowing tools.
Figure 45. Dust collector with hood.
-30-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTENANCE
Cleaning &
Protecting
To reduce risk of shock or
accidental startup, always
disconnect machine from
power before adjustments,
maintenance, or service.
Cleaning the Model T25920/T25926 is relatively
easy. Vacuum excess wood chips and sawdust,
and wipe off the remaining dust with a dry cloth.
If any resin has built up, use a resin dissolving
cleaner to remove it.
Schedule
Protect the unpainted cast iron lathe bed by wip-
ing it clean with a lightly oiled rag after every
use—this ensures moisture from wood dust does
not remain on bare metal surfaces. Keep the bed
rust-free with regular applications of products like
G96® Gun Treatment, SLIPIT®, or Boeshield® T-9.
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
Ongoing:
•
•
•
•
•
Loose faceplate or mounting bolts.
Damaged center or tooling.
Worn or damaged wires.
Loose machine components.
Any other unsafe condition.
Lubrication
Lubricate locations shown in Figure 48 with light
machine oil or G96® Gun Treatment.
Daily:
•
Clean off dust buildup.
•
Clean and lubricate lathe bed, spindle, and
quill.
Lubrication Point
Monthly:
Belt tension, damage, or wear.
•
Lubrication
Points
Figure 48. Lubrication locations.
-31-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: SERVICE
Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-
ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical
Support at (570) 546-9663.
Troubleshooting
Motor & Electrical
Symptom
Possible Cause
Possible Solution
Machine does not
start or a breaker
trips.
1. Switch disabling key removed.
2. Incorrect power supply voltage or circuit
size.
1. Install switch disabling key.
2. Ensure correct power supply voltage and circuit
size.
3. Blown fuse.
3. Replace fuse/ensure no shorts.
4. Power supply circuit breaker tripped or fuse 4. Ensure circuit is sized correctly and free of shorts.
blown.
Reset circuit breaker or replace fuse.
5. Check for broken wires or disconnected/corroded
connections, and repair/replace as necessary.
6. Test/replace.
5. Wiring is open/has high resistance.
6. Potentiometer/variable-speed dial at fault.
7. ON/OFF switch at fault.
8. Motor brushes at fault.
7. Replace switch.
8. Replace motor brushes.
9. Motor is at fault.
9. Test/repair/replace.
Machine stalls or is 1. Machine is undersized for task.
1. Use sharp lathe tools; reduce feed rate/depth of cut.
2. Only cut wood/ensure moisture is below 20%.
3. Decrease feed rate/cutting speed.
4. Replace bad belt and re-tension (see Page 34).
5. Correct motor wiring connections.
6. Replace loose pulley.
underpowered.
2. Workpiece material not suitable.
3. Feed rate/cutting speed too fast for task.
4. Belt slipping.
5. Motor connection is wired incorrectly.
6. Pulley slipping on shaft.
7. Plug/receptacle at fault.
7. Test for good contacts/correct wiring.
8. Clean off motor, let cool, and reduce workload.
9. Test/replace.
8. Motor has overheated.
9. Potentiometer/variable-speed dial at fault.
10. Motor brushes at fault.
10. Replace motor brushes.
11. Pulley/sprocket slipping on shaft
12. Motor is at fault.
11. Replace loose pulley/shaft.
12. Test/repair/replace.
Machine has
1. Machine incorrectly mounted to workbench 1. Adjust feet, shim, or tighten mounting hardware.
or floor.
vibration or noisy
operation (without
workpiece installed).
2. Motor or component is loose.
2. Inspect/replace stripped or damaged bolts/nuts, and
re-tighten with thread locking fluid-4
3. Inspect/replace belts (see Page 34).
4. Tighten/replace.
3. Belt worn or loose.
4. Motor mount loose/broken.
5. Pulley is loose.
5. Replace shaft, pulley, setscrew, and key as
required.
6. Motor bearings are at fault.
7. Workpiece or chuck at fault.
6. Test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
7. Center workpiece in chuck/faceplate; reduce RPM;
replace defective chuck.
-32-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Wood Lathe Operation
Symptom
Possible Cause
Corrective Action
Vibration noise while
machine is running; noise
changes when speed is
changed.
1. Belt cover loose.
1. Tighten the knobs that secure the belt cover; if nec-
essary install a soft, vibration dampening material
between the belt cover and the headstock casting.
Excessive vibration (with
workpiece installed).
1. Workpiece mounted incorrectly.
1. Re-mount workpiece, making sure that centers are
embedded in true center of workpiece.
2. Headstock, tailstock, or tool rest not 2. Check clamp levers and tighten if necessary.
securely clamped to lathe bed.
3. Workpiece warped, out of round, or 3. Cut workpiece to correct, or use a different
is flawed.
workpiece.
4. Spindle speed is set too fast for
mounted workpiece.
4. Reduce the spindle speed.
5. Lathe is resting on an uneven sur-
face.
5. Shim base or adjust feet on workbench to remove
any wobbles.
6. Motor mount bolts are loose.
7. Belt is worn or damaged.
8. Spindle bearings are worn.
6. Tighten motor mount bolts.
7. Replace belt (see Page 34).
8. Replace spindle bearings.
Chisels grab or dig into
workpiece.
1. Tool rest set too low.
1. Set tool rest higher. See Page 21 for how to prop-
erly set tool rest height.
2. Tool rest set too far from workpiece. 2. Move the tool rest closer to the workpiece. See
Page 21 for the proper workpiece/tool rest clear-
ance.
3. Wrong chisel/tool being used.
3. Use the correct chisel/tool; educate yourself by
reading books, trade magazines, or seeking help
from an experienced lathe operator.
4. Chisel/tool dull.
4. Sharpen or replace the chisel/tool you are using.
Bad surface finish on
workpiece.
1. Wrong spindle speed.
2. Dull chisel or wrong chisel being
used for the operation.
1. Use trial-and-error to find a better spindle speed.
2. Sharpen chisel or try a different chisel.
Tailstock moves under
load.
1. Tailstock mounting bolt loose.
2. Bed surface is oily or greasy.
1. Tighten.
2. Clean bed surface to remove excess oil/grease.
Can't remove tapered tool
from tailstock barrel.
1. Tailstock barrel not retracted all the 1. Turn the barrel handwheel until it forces taper out of
way back into the tailstock.
2. Debris was not removed from taper
before inserting into barrel.
barrel.
2. Always make sure that taper surfaces are clean.
-33-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Tensioning &
Replacing Belt
Pulley
1
⁄2
"
The drive belt stretches as the lathe is used.
Most of the stretching will occur during the first
16 hours, but may continue with further use. If the
lathe loses power while making a cut, the belt may
be slipping and need tensioning. If the belt shows
signs of excessive wear, or damage, replace it.
Deflection
Pulley
Figure 50. Checking belt deflection.
5. Re-install rear access cover.
Tools Needed:
Hex Wrenches 3mm, 6mm...........................1 Ea
Rubber/Wood Mallet.......................................... 1
Replacing Belt
1. DISCONNECT MACHINE FROM POWER!
Tensioning Belt
1. DISCONNECT MACHINE FROM POWER!
2. Remove rear access cover and open side
access cover.
2. Remove rear access cover and loosen belt
tension screw (see Figure 49).
3. Release belt tension, then remove belt from
motor pulley.
4. Loosen set screws on spindle handwheel (see
Figure 51), and turn clockwise to unthread
and remove.
Spindle Pulley
Set Screw
Belt Tension Lever
Belt Tension Screw
Spindle
Handwheel
Set Screw
Figure 49. Belt tension controls.
3. Press belt tension lever down, then tighten
belt tension screw.
Figure 51. Set screw locations.
4. Press belt with moderate pressure in center
5. Loosen spindle pulley set screw.
to check tension. Belt is correctly tensioned
1
when there is approximately ⁄2" deflection
6. Tap spindle far enough out of headstock
so belt can be removed (see Figure 52 on
Page 35). A rubber or wooden mallet may be
required. Take care not to damage spindle
threads or lose parts. DO NOT remove spin-
dle pulley.
when pushed as shown in Figure 50.
1
— If there is more than ⁄2" deflection repeat
the tensioning procedure until it is correct.
If tension cannot be achieved replace belt.
-34-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Fuse
This lathe features an on-board fuse designed
to protect sensitive electrical parts from ther-
mal damage in the event of an overload. If the
machine does not start check the fuse.
To replace fuse:
Figure 52. Belt removal (pulley removed for
clarity).
1. DISCONNECT MACHINE FROM POWER!
7. Place new belt over spindle pulley.
2. Remove (4) Phillips head screws holding
electrical box to side access cover (see
Figure 53).
8. Slide spindle back through headstock and into
original position. A mallet may be required to
reseat bearing.
9. Install headstock spindle handwheel and
tighten both set screws.
10. Loosely install belt on inner or outermost
motor pulley position.
Phillips Head
Screws
11. Move belt tension lever down to tension belt
then tighten belt tension screw.
12. Follow Step 4 in the Tensioning Belt proce-
Figure 53. Electrical box screw locations, (side
dure to set belt tension.
access door open for clarity).
13. Re-install rear access cover and close side
3. Carefully remove fuse, then insert new fuse
shown in Figure 54.
access cover.
Figure 54. 10A fuse location on circuit board.
4. Re-install electrical box onto side access
cover with screws removed in Step 2, then
test run.
-35-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Carefully remove brush from motor (see
Figure 56).
Replacing Brushes
Your machine is equipped with a universal motor
that uses carbon brushes to transmit electri-
cal current inside the motor. These brushes
are considered to be regular "wear items" or
"consumables" that will eventually need to be
replaced. The frequency of this replacement is
directly related to how much the motor is used
and how hard it is pushed.
Replacethecarbonbrusheswhenthemotornolon-
ger reaches full power, or when the brushes mea-
sure less than 1⁄4" long (new brushes are 5⁄8" long).
Figure 56. Removing brush from motor.
Tools Needed
Hex Wrench 6mm.............................................. 1
Qty
5. Install new brush and re-install brush cap.
Flat Head Screwdriver #2.................................. 1
6. Repeat Steps 3–5 to replace brush on top-
side of motor.
T25920/T25926: Both models use same motor
replacement brushes (Part# PT25920084).
7. Tension belt (refer to Tensioning &
Replacing Belt on Page 34 for details).
Replacing Lathe Motor Brushes
1. DISCONNECT MACHINE FROM POWER!
8. Re-install rear access cover, and close side
access cover.
2. Loosen belt tension screw, raise motor to
gain access to lower brush cap, then tighten
belt tension screw.
9. Test run machine.
3. Unscrew brush cap with flat head screwdriver
(see Figure 55).
Brush Cap
Locations
Figure 55. Motor brush cap locations.
-36-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
machine
SECTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-
es to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is con- WIRE/COMPONENT DAMAGE. Damaged wires
nected to a power source is extremely dangerous. or components increase the risk of serious per-
Touching electrified parts will result in personal sonal injury, fire, or machine damage. If you notice
injury including but not limited to severe burns, that any wires or components are damaged while
electrocution, or death. Disconnect the power performing a wiring task, replace those wires or
from the machine before servicing electrical com- components.
ponents!
MOTOR WIRING. The motor wiring shown in
MODIFICATIONS. Modifying the wiring beyond these diagrams is current at the time of printing
what is shown in the diagram may lead to unpre- but may not match your machine. If you find this
dictable results, including serious injury or fire. to be the case, use the wiring diagram inside the
This includes the installation of unapproved after- motor junction box.
market parts.
CAPACITORS/INVERTERS. Some capacitors
WIRE CONNECTIONS. All connections must and power inverters store an electrical charge for
be tight to prevent wires from loosening during up to 10 minutes after being disconnected from
machine operation. Double-check all wires dis- the power source. To reduce the risk of being
connected or connected during any wiring task to shocked, wait at least this long before working on
ensure tight connections.
capacitors.
CIRCUIT REQUIREMENTS. You MUST follow EXPERIENCING DIFFICULTIES. If you are expe-
the requirements at the beginning of this manual
riencing difficulties understanding the information
when connecting your machine to a power source. included in this section, contact our Technical
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
-37-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
T25920/T25926 Wiring Diagram
DRO XBS2012.6.11
Neutral
Hot
Ground
Transformer
Figure 57. Digital readout display board.
110 VAC
5-15 Plug
Potentiometer
B103
Spindle Control
Circuit Board
DZ-236A1
250VAC
A1218
Figure 58. Connections in headstock.
Toggle Switch
(viewed from behind)
RU CB-8
E19 4417
Circuit
Breaker
RU L2
Ground
6A
50VDC
Figure 59. Electrical box.
MOTOR 110V
READ ELECTRICAL SAFETY
-38-
Model T25920/T25926 (Mfd. Since 08/14)
ON DPoAwGnloEad3fr7om! Www.Somanuals.com. All Manuals Search And Download.
SECTION 9: PARTS
T25920 Breakdown
5
8
9
5
6
74
6
74
7
2
1
20
18
10
21
2
11
19
3
4
13
13
17
83
4
81
12
22
18
14
15
80
78
82
16
23
77
65
27
45
67
62
60
63
66
61
58
59
54
64
68
30
33
31
2
32
79
69
38
53
55
34
52
57
73
35
56
37
2
36
41
42
51
39
74
47
76
41
72
50
84
71
49
48
40
28
25
24
44
26
43
46
70
29
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-39-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
T25920 Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PT25920001 HANDWHEEL 82MM X M18-2.5 LH BORE
PT25920002 SET SCREW M6-1 X 12
PT25920003 COLLAR SPINDLE
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
76
77
78
79
80
81
82
83
84
PT25920043 MOTOR PLATE HANDLE ASSEMBLY
2
PT25920044 MOTOR CORD 18G 3W 16"
PT25920045 SWITCH CORD 18G 3W 22"
PT25920046 MOTOR CARBON BRUSH CAP
PT25920047 CAP SCREW M8-1.25 X 12
PT25920048 MOTOR MOUNT PLATE
PT25920049 FLAT WASHER 6MM
3
4
PT25920004 BALL BEARING 80105
PT25920005 CAP SCREW M8-1.25 X 25
PT25920006 LOCK WASHER 8MM
PT25920007 REAR BELT ACCESS DOOR
PT25920008 THUMB SCREW M5-.8 X 9
PT25920009 STATIONARY KNOB M5-.8
PT25920010 SHOULDER SCREW M5-.8 X 7, 2
PT25920011 FLAT HD SCR M5-.8 X 10
PT25920012 HEADSTOCK
5
6
7
8
PT25920050 LOCK WASHER 6MM
PT25920051 MOTOR PULLEY
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
PT25920052 DRIVE PULLEY
PT25920053 POLY V-BELT 3V X 25L
PT25920054 SWITCH BOX LATCH BOLT M4-.7 X 5
PT25920055 WAVY WASHER 6MM
PT25920056 SWITCH BOX LATCH
PT25920057 FLAT WASHER 4MM
PT25920013 INT RETAINING RING 47MM
PT25920014 HEADSTOCK SPINDLE
PT25920015 FACEPLATE 3-1/4"
PT25920016 SPUR CENTER MT#2
PT25920017 TOOL REST LOCK HANDLE
PT25920018 EXT RETAINING RING 10MM
PT25920019 TOOLREST BUSHING
PT25920020 TOOLREST 150MM
PT25920058 HINGE
PT25920059 PHLP HD SCR M4-.7 X 8
PT25920060 SWITCH BOX PLATE
PT25920061 HINGE PIN
PT25920062 POWER CORD 18G 3W 72" 5-15P
PT25920063 CIRCUIT BREAKER 6A GENERAL
PT25920064 CIRCUIT BOARD
PT25920021 TOOLREST BASE
PT25920022 TOOLREST CAM FOLLOWER
PT25920023 ADJUSTABLE HANDLE M8-1.25 X 20
PT25920024 HEX WRENCH 3MM
PT25920065 PHLP HD SCR M4-.7 X 6
PT25920066 SWITCH BOX
PT25920025 HEX WRENCH 6MM
PT25920067 POTENTIOMETER B103
PT25920068 TOGGLE SWITCH RU CB-8 E19 4417
PT25920069 SET SCREW M6-1 X 12
PT25920070 MOTOR 550W 110VDC
PT25920071 RUBBER FOOT M8-1.25 X 15
PT25920072 LOCK NUT M8-1.25
PT25920026 HEX WRENCH 8MM
PT25920027 LIVE CENTER MT#2
PT25920028 FENDER WASHER 8MM
PT25920029 MOTOR CARBON BRUSH 2-PC SET
PT25920030 TAILSTOCK LEADSCREW
PT25920031 TAILSTOCK QUILL
PT25920073 EXT RETAINING RING 10MM
PT25920074 FLAT WASHER 8MM
PT25920032 TAILSTOCK
PT25920033 TAILSTOCK LEVER
PT25920076 FLAT HD SCR M6-1 X 12
PT25920077 STRAIN RELIEF 5/16" SNAP-IN ST
PT25920078 STRAIN RELIEF 1/4" SNAP-IN ST
PT25920079 FUSE 10A 250V FAST-ACTING GLASS
PT25920080 DIGITAL DISPLAY COVER
PT25920081 DIGITAL DISPLAY PLATE
PT25920082 PHLP HD SCR M4-.7 X 16
PT25920083 TRANSFORMER 110V/9V
PT25920084 KNOCKOUT BAR
PT25920034 HANDWHEEL 83MM X 15MM BORE
PT25920035 HANDWHEEL HANDLE 6MM X 50MM
PT25920036 SHOULDER SCREW M6-1 X 53
PT25920037 TAILSTOCK CLAMP BOLT M8-1.25 X 30
PT25920038 BED
PT25920039 RETAINING PLATE
PT25920040 CAP SCREW M10-1.5 X 12
PT25920041 LOCK PLATE
PT25920042 LOCK NUT M10-1.5
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
-40-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
T25926 Breakdown
5
8
9
5
6
74
6
74
7
2
1
20
18
10
21
2
11
19
3
4
13
13
17
83
4
81
12
22
18
14
15
80
78
82
16
23
77
65
27
45
67
62
60
63
66
61
58
59
54
64
68
30
33
31
2
32
79
69
38
53
55
34
52
57
73
35
56
37
2
36
41
42
51
39
74
47
76
41
72
50
84
71
49
48
40
28
25
24
44
26
43
46
70
29
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-41-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
T25926 Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PT25926001 HANDWHEEL 82MM X M18-2.5 LH BORE
PT25926002 SET SCREW M6-1 X 12
PT25926003 COLLAR SPINDLE
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
76
77
78
79
80
81
82
83
84
PT25926043 MOTOR PLATE HANDLE ASSEMBLY
2
PT25926044 MOTOR CORD 18G 3W 16"
PT25926045 SWITCH CORD 18G 3W 22"
PT25926046 MOTOR CARBON BRUSH CAP
PT25926047 CAP SCREW M8-1.25 X 12
PT25926048 MOTOR MOUNT PLATE
PT25926049 FLAT WASHER 6MM
3
4
PT25926004 BALL BEARING 80105
PT25926005 CAP SCREW M8-1.25 X 25
PT25926006 LOCK WASHER 8MM
PT25926007 REAR BELT ACCESS DOOR
PT25926008 THUMB SCREW M5-.8 X 9
PT25926009 STATIONARY KNOB M5-.8
PT25926010 SHOULDER SCREW M5-.8 X 7, 2
PT25926011 FLAT HD SCR M5-.8 X 10
PT25926012 HEADSTOCK
5
6
7
8
PT25926050 LOCK WASHER 6MM
PT25926051 MOTOR PULLEY
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
PT25926052 DRIVE PULLEY
PT25926053 POLY V-BELT 3V X 25L
PT25926054 SWITCH BOX LATCH BOLT M4-.7 X 5
PT25926055 WAVY WASHER 6MM
PT25926056 SWITCH BOX LATCH
PT25926057 FLAT WASHER 4MM
PT25926013 INT RETAINING RING 47MM
PT25926014 HEADSTOCK SPINDLE
PT25926015 FACEPLATE 3-1/8"
PT25926016 SPUR CENTER MT#2
PT25926017 TOOL REST LOCK HANDLE
PT25926018 EXT RETAINING RING 10MM
PT25926019 TOOLREST BUSHING
PT25926020 TOOLREST 145MM
PT25926058 HINGE
PT25926059 PHLP HD SCR M4-.7 X 8
PT25926060 SWITCH BOX PLATE
PT25926061 HINGE PIN
PT25926062 POWER CORD 18G 3W 72" 5-15P
PT25926063 CIRCUIT BREAKER 4A GENERAL
PT25926064 CIRCUIT BOARD
PT25926021 TOOLREST BASE
PT25926022 TOOLREST CAM FOLLOWER
PT25926023 ADJUSTABLE HANDLE M8-1.25 X 20
PT25926024 HEX WRENCH 3MM
PT25926065 PHLP HD SCR M4-.7 X 6
PT25926066 SWITCH BOX
PT25926025 HEX WRENCH 6MM
PT25926067 POTENTIOMETER B103
PT25926068 TOGGLE SWITCH RU CB-8 E19 4417
PT25926069 SET SCREW M6-1 X 12
PT25926070 MOTOR 375W 110VDC
PT25926071 RUBBER FOOT M8-1.25 X 15
PT25926072 LOCK NUT M8-1.25
PT25926026 HEX WRENCH 8MM
PT25926027 LIVE CENTER MT#2
PT25926028 FENDER WASHER 8MM
PT25926029 MOTOR CARBON BRUSH 2-PC SET
PT25926030 TAILSTOCK LEADSCREW
PT25926031 TAILSTOCK QUILL
PT25926073 EXT RETAINING RING 10MM
PT25926074 FLAT WASHER 8MM
PT25926032 TAILSTOCK
PT25926033 TAILSTOCK LEVER
PT25926076 FLAT HD SCR M6-1 X 12
PT25926077 STRAIN RELIEF 5/16" SNAP-IN ST
PT25926078 STRAIN RELIEF 1/4" SNAP-IN ST
PT25926079 FUSE 10A 250V FAST-ACTING GLASS
PT25926080 DIGITAL DISPLAY COVER
PT25926081 DIGITAL DISPLAY PLATE
PT25926082 PHLP HD SCR M4-.7 X 16
PT25926083 TRANSFORMER 110V/9V
PT25926084 KNOCKOUT BAR
PT25926034 HANDWHEEL 83MM X 15MM BORE
PT25926035 HANDWHEEL HANDLE 6MM X 50MM
PT25926036 SHOULDER SCREW M6-1 X 53
PT25926037 TAILSTOCK CLAMP BOLT M8-1.25 X 30
PT25926038 BED
PT25926039 RETAINING PLATE
PT25926040 CAP SCREW M10-1.5 X 12
PT25926041 LOCK PLATE
PT25926042 LOCK NUT M10-1.5
-42-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
T25920/T25926 Labels & Cosmetics
MODEL T25920
12"
X
18" VARIABLE-SPEED WOOD LATHE
Specifications
Motor: 3/4 HP 110V, 1-Ph, 60 Hz, 5.3A
Spindle Speeds: 650 3800 RPM
Distance Between Centers: 16-1/2"
Swing Over Bed: 12"
WARNING!
,
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
–
2. Always wear safety glasses, face shield, and respirator.
3. DO NOT wear loose clothing, gloves, jewelry; tie back long hair.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece before mounting.
Swing Over Tool Rest: 9-1/2"
Spindle Size: 1"
x
8
TPI RH
Spindle Tailstock Taper: MT#2
&
Weight: 84 Lbs.
8. Use lowest speed when starting
a
new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or use in wet locations.
Date
S/N
Mfd. for Grizzly in China
13. Prevent unauthorized use by children or untrained users.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
85
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
EYE/FACE INJURY
HAZARD!
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
To get
a
new manual,
call (800) 523-4777 or
88
WARNING!
ENTANGLEMENT
HAZARD!
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
87
grizzly.com
17
x
NOTICE
Check carbon brushes inside
motor regularly to avoid damage
to machine during operation.
86
89
91
90
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
85
85
86
87
PT25920085 MACHINE ID LABEL (T25920)
PT25926085 MACHINE ID LABEL (T25926)
PT25920086 GRIZZLY.COM LABEL
88
89
90
91
PT25920088 SHOCK HAZARD LABEL
PT25920089 ELECTRICITY LABEL
PT25920090 CARBON BRUSHES NOTICE LABEL
PT25920091 GRIZZLY GREEN TOUCH-UP PAINT
PT25920087 SAFETY WARNING LABEL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
-43-
Model T25920/T25926 (Mfd. Since 08/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email _________________________________________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Woodwork
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Shotgun News
____ Today’s Homeowner
____ Wood
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
____ 6-9
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY & RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Humidifier ti25442a User Manual
Grizzly Automobile Parts T23121 User Manual
Grizzly Paint Sprayer H6330 User Manual
Grizzly Saw G4227 User Manual
Grizzly Staple Gun H7677 User Manual
Haier Air Cleaner HRF 518W User Manual
Havis Shields Automobile Accessories C 3619 User Manual
Honeywell Portable Generator 5973 User Manual
HP Hewlett Packard All in One Printer PSC 2210 User Manual
Impex Home Gym IGS 01 User Manual