Grizzly Lathe H8259 User Manual

MODEL H8259

10" x 18" BENCHTOP LATHE

OWNER'S MANuAL

WARNiNg: NO PORTiON Of THiS MANuAL MAy BE REPRODuCED iN ANy SHAPE

OR fORM WiTHOuT THE WRiTTEN APPROvAL Of gRizzLy iNDuSTRiAL, iNC.

(For maChines manuFaCtured aFter 10/07) #Jb9951 printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

iNTRODuCTiON............................................................................................................................... 2

Foreword .................................................................................................................................... 2

Contact info................................................................................................................................ 2

machine data sheet................................................................................................................... 3

identification ............................................................................................................................... 5

SECTiON 1: SAfETy....................................................................................................................... 6

safety instructions for machinery............................................................................................... 6

additional safety for Wood lathes............................................................................................. 8

SECTiON 2: CiRCuiT REQuiREMENTS ........................................................................................ 9

110v operation .......................................................................................................................... 9

SECTiON 3: SET uP...................................................................................................................... 10

set up safety........................................................................................................................... 10

items needed for setup ........................................................................................................... 10

unpacking ................................................................................................................................ 10

inventory................................................................................................................................... 10

Clean up .................................................................................................................................. 11

site Considerations .................................................................................................................. 11

assembly.................................................................................................................................. 12

test run................................................................................................................................... 12

SECTiON 4: OPERATiONS ........................................................................................................... 13

operation safety ...................................................................................................................... 13

Changing speeds..................................................................................................................... 13

adjusting tailstock ................................................................................................................... 14

adjusting tool rest.................................................................................................................. 15

installing/removing spur Center ............................................................................................. 16

installing/removing live Center .............................................................................................. 16

installing/removing Faceplate ................................................................................................. 17

selecting turning tools ........................................................................................................... 18

spindle turning ........................................................................................................................ 19

Faceplate turning .................................................................................................................... 20

sanding/Finishing..................................................................................................................... 21

SECTiON 5: ACCESSORiES......................................................................................................... 22

SECTiON 6: MAiNTENANCE......................................................................................................... 24

schedule .................................................................................................................................. 24

Cleaning ................................................................................................................................... 24

unpainted Cast iron ................................................................................................................. 24

lubrication................................................................................................................................ 24

Changing belt........................................................................................................................... 25

SECTiON 7: SERviCE ................................................................................................................... 26

troubleshooting........................................................................................................................ 26

h8259 Wiring diagram............................................................................................................. 28

main breakdown....................................................................................................................... 29

parts list .................................................................................................................................. 30

Warning labels breakdown & parts list.................................................................................. 31

WARRANTy AND RETuRNS........................................................................................................ 35

Download from Www.Somanuals.com. All Manuals Search And Download.

iNTRODuCTiON

Contact info

foreword

if you have any comments regarding this manual,

please write to us at the address below:

We are proud to offer the model h8259 10" x 18"

benchtop lathe. this machine is part of a grow-

ing grizzly family of fine woodworking machinery.

When used according to the guidelines set forth in

this manual, you can expect years of trouble-free,

enjoyable operation and proof of grizzly’s com-

mitment to customer satisfaction.

grizzly industrial, inc.

technical documentation manager

p.o. box 2069

bellingham, Wa 98227-2069

email: manuals@grizzly.com

We are pleased to provide this manual with

the model h8259. it was written to guide you

through assembly, review safety considerations,

and cover general operating procedures. it repre-

sents our effort to produce the best documenta-

tion possible.

We stand behind our machines. if you have any

service questions or parts requests, please call or

write us at the location listed below.

grizzly industrial, inc.

1203 lycoming mall Circle

muncy, pa 17756

phone: (570) 546-9663

Fax: (800) 438-5901

the specifications, drawings, and photographs

illustrated in this manual represent the model

h8259 as supplied when the manual was pre-

pared. however, owing to grizzly’s policy of con-

tinuous improvement, changes may be made at

any time with no obligation on the part of grizzly.

For your convenience, we always keep current

grizzly manuals available on our website at www.

grizzly.com. any updates to your machine will be

reflected in these manuals as soon as they are

complete. visit our site often to check for the lat-

est updates to this manual!

e-mail: techsupport@grizzly.com

Web site: http://www.grizzly.com

-2-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL H8259 10" X 18" BENCH-TOP WOOD LATHE

Product Dimensions:

Weight................................................................................................................................................................ 73 lbs.

Length/Width/Height....................................................................................................................... 36 x 11-1/2 x 15 in.

Foot Print (Length/Width)................................................................................................................... 29-1/2 x 7-1/2 in.

Shipping Dimensions:

Type............................................................................................................................................................. Cardboard

Content............................................................................................................................................................ Machine

Weight................................................................................................................................................................ 77 lbs.

Length/Width/Height............................................................................................................................. 33 x 17 x 12 in.

Electrical:

Switch.............................................................................................................................Paddle Type w/Disabling Key

Switch Voltage........................................................................................................................................................ 110

Cord Length............................................................................................................................................................ 6 ft.

Cord Gauge....................................................................................................................................................18 guage

Minimum Circuit Size.............................................................................................................................................. 15A

Plug Included......................................................................................................................................................... 5-15

Motors:

Main

Type............................................................................................................................................ Capacitor Start

Horsepower....................................................................................................................................................1/2

Voltage..........................................................................................................................................................110

Prewired........................................................................................................................................................110

Phase........................................................................................................................................................Single

Amps.................................................................................................................................................................7

Speed..........................................................................................................................................................1725

Cycle............................................................................................................................................................... 60

Number Of Speeds........................................................................................................................................... 1

Power Transfer ...................................................................................................................................Belt Drive

Bearings....................................................................................................................... Shielded and Lubricated

Main Specifications:

Operation Information

Swing Over Bed......................................................................................................................................... 10 in.

Dist Between Centers.................................................................................................................................18 in.

Swing Over Tool Rest............................................................................................................................ 4-1/2 in.

No Of Spindle Speeds.......................................................................................................................................5

826, 1205, 1713, 2422, 3337 RPM

Range Of Spindle Speeds..............................................................................606, 917, 1343, 1960, 2800 RPM

Floor To Center Height.................................................................................................................................5 in.

Spindle Information

Spindle Type..................................................................................................................................... Right Hand

Spindle Taper.............................................................................................................................................MT#2

Spindle Size................................................................................................................................................. 1 in.

Spindle Bore..........................................................................................................................................0.394 in.

Spindle Center.............................................................................................................................................Spur

Spindle TPI........................................................................................................................................................8

-3-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Tailstock Information

Tailstock Taper.......................................................................................................................................... MT#2

Tailstock Center............................................................................................................................................Live

Construction

Bed Construction..................................................................................................................................Cast Iron

Frame Construction..............................................................................................................Cast Iron and Steel

Headstock Construction....................................................................................................... Cast Iron and Steel

Tailstock Construction..........................................................................................................Cast Iron and Steel

Paint..........................................................................................................................................................Epoxy

Other Related Information

Bed Width...............................................................................................................................................7-1/4 in.

Faceplate Size..............................................................................................................................................3 in.

Other Specifications:

Country Of Origin ................................................................................................................................................China

Warranty ............................................................................................................................................................ 1 Year

Serial Number Location ........................................................................................................Data Label on Lathe Bed

Assembly Time .................................................................................................................................................10 min.

-4-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

identification

figure 1. model h8259 identification.

A. headstock

B. Faceplate

C. spur Center

D. tool rest

K. tool rest base

L. side access Cover

M. leveling Foot

N. belt tension lever

O. belt tension screw

E. tool rest lock handle

f. tool rest base release lever

g. live Center

H. Quill lock handle

i. Quill handwheel

J. tailstock

P. motor

Q. lathe bed

R. on/oFF switch w/disabling Key

S. tailstock release lever

T. rear access Cover

-5-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This

manual uses a series of symbols and signal words intended to convey the level of importance

of the safety messages. The progression of symbols is described below. Remember that safety

messages by themselves do not eliminate danger and are not a substitute for proper accident

prevention measures.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

This symbol is used to alert the user to useful information about

proper operation of the machine.

NOTICE

Safety Instructions for Machinery

1. READ ENTIRE MANUAL BEFORE

STARTING. Operating machine before

reading the manual greatly increases the

risk of injury.

4. ALWAYS USE HEARING PROTECTION

WHEN OPERATING MACHINERY.

Machinery noise can cause permanent

hearing loss.

5. WEAR PROPER APPAREL. DO NOT

wear loose clothing, gloves, neckties, rings,

or jewelry that can catch in moving parts.

Wear protective hair covering to contain

long hair and wear non-slip footwear.

2. ALWAYS USE ANSI APPROVED

SAFETY GLASSES WHEN OPERATING

MACHINERY. Everyday eyeglasses only

have impact resistant lenses—they are

NOT safety glasses.

6. NEVER OPERATE MACHINERY WHEN

TIRED OR UNDER THE INFLUENCE OF

DRUGS OR ALCOHOL. Be mentally alert

at all times when running machinery.

3. ALWAYS WEAR A NIOSH APPROVED

RESPIRATOR WHEN OPERATING

MACHINERY THAT PRODUCES DUST.

Most types of dust (wood, metal, etc.) can

cause severe respiratory illnesses.

-6-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Instructions for Machinery

7. ONLY ALLOW TRAINED AND PROP-

16. REMOVE CHUCK KEYS OR ADJUSTING

ERLY SUPERVISED PERSONNEL TO

OPERATE MACHINERY. Make sure

operation instructions are safe and clearly

understood.

TOOLS. Make a habit of never leaving

chuck keys or other adjustment tools in/on

the machine—especially near spindles!

17. DAMAGED MACHINERY. Check for bind-

ing or misaligned parts, broken parts,

loose bolts, other conditions that may

impair machine operation. Always repair or

replace damaged parts before operation.

8. KEEP CHILDREN/VISITORS AWAY.

Keep all children and visitors away from

machinery. When machine is not in use,

disconnect it from power, lock it out, or

disable the switch to make it difficult for

unauthorized people to start the machine.

18. DO NOT FORCE MACHINERY. Work at

the speed for which the machine or acces-

sory was designed.

9. UNATTENDED OPERATION. Leaving

machine unattended while its running

greatly increases the risk of an accident or

property damage. Turn machine Off and

allow all moving parts to come to a com-

plete stop before walking away.

19. SECURE WORKPIECE. Use clamps or

a vise to hold the workpiece when practi-

cal. A secured workpiece protects your

hands and frees both hands to operate the

machine.

10. DO NOT USE IN DANGEROUS

ENVIRONMENTS. DO NOT use machin-

ery in damp, wet locations, or where any

flammable or noxious fumes may exist.

20. DO NOT OVERREACH. Maintain stability

and balance at all times when operating

machine.

21. MANY

MACHINES

CAN

EJECT

11. KEEP WORK AREA CLEAN AND WELL

LIGHTED. Clutter and dark shadows may

cause accidents.

WORKPIECES TOWARD OPERATOR.

Know and avoid conditions that cause the

workpiece to "kickback."

12. USE A GROUNDED POWER SUPPLY

RATEDFORTHEMACHINEAMPERAGE.

Grounded cords minimize shock hazards.

Operating machine on an incorrect size of

circuit increases risk of fire.

22. STABLE MACHINE. Machines that move

during operations greatly increase the

risk of injury and loss of control. Verify

machines are stable/secure and mobile

bases (if used) are locked before starting.

13. ALWAYS DISCONNECT FROM POWER

23. CERTAIN DUST MAY BE HAzARDOUS

to the respiratory systems of people and

animals, especially fine dust. Be aware of

the type of dust you are exposed to and

always wear a respirator designed to filter

that type of dust.

SOURCE

BEFORE

SERVICING

MACHINERY. Make sure switch is in OFF

position before reconnecting.

14. MAINTAIN MACHINERY WITH CARE.

Keep blades sharp and clean for best and

safest performance. Follow instructions for

lubricating and changing accessories.

24. EXPERIENCING DIFFICULTIES. If at

any time you are experiencing difficulties

performing the intended operation, stop

using the machine! Contact our Technical

Support Department at (570) 546-9663.

15. MAKE SURE GUARDS ARE IN PLACE

AND WORK CORRECTLY BEFORE

USING MACHINERY.

-7-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Safety for Wood Lathes

9. OPERATiNg DAMAgED LATHE. never

operate the lathe with damaged or worn

parts.

1. KEEPiNg guARDS iN PLACE. make sure

all guards are in place and that the lathe sits

on a flat, stable surface.

10. ADJuSTMENTS/MAiNTENANCE. make

sure your wood lathe is turned OFF, dis-

connected from its power source, and all

moving parts have come to a complete stop

before starting any inspection, adjustment,

or maintenance procedure.

2. EyE/fACE PROTECTiON. always wear

eye protection or a face shield when operat-

ing the lathe.

3. RESPiRATORy PROTECTiON. always

wear a respirator when using this machine.

Wood dust may cause allergies or long-

term respiratory health problems.

11. STOPPiNg LATHE. do not stop the lathe

by using your hand against the workpiece.

allow the lathe to stop on its own.

4. MOuNTiNg WORKPiECE. before starting,

be certain the workpiece has been properly

imbedded on the headstock and tailstock

centers and that there is adequate clear-

ance for the full rotation.

12. AvOiDiNg ENTANgLEMENT. Keep long

hair and loose clothing articles such as

sleeves, belts, and jewelry items away from

the lathe spindle.

5. WORKPiECE CONDiTiON. always inspect

the condition of your workpiece. do not

turn pieces with knots, splits, and other

potentially dangerous conditions. make sure

joints of glued-up pieces have high quality

bonds and won't fly apart during operation.

13. fACEPLATE TuRNiNg. When faceplate

turning, use lathe chisels on the downward

spinning side of the workpiece only.

14. SANDiNg/POLiSHiNg. remove the tool

rest when performing sanding or polishing

operations on the rotating spindle.

6. ADJuSTiNg TOOL REST. adjust tool rest

to provide proper support for the turning tool

you will be using. test tool rest clearance

by rotating workpiece by hand before turn-

ing lathe ON.

15. MATERiAL REMOvAL RATE. removing

too much material at once may cause

workpiece to fly out of the lathe.

16. REDuCiNg WORKPiECE viBRATiON. if

the workpiece vibrates, immediately turn

the lathe OFF. Check to make sure the

workpiece is centered and balanced. trim

excess waste off corners with a bandsaw

or table saw to reduce vibration. make sure

workpiece is securely attached in setup.

7. TuRNiNg SPEED. select the correct tun-

ing speed for your work, and allow the lathe

to gain full speed before operating.

8. uSiNg SHARP CHiSELS. Keep lathe chis-

els properly sharpened and held firmly in

position when turning.

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your

individual working conditions. use this and

other machinery with caution and respect.

failure to do so could result in serious per-

sonal injury, damage to equipment, or poor

work results.

Like all machinery there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. use this machine

with respect and caution to lessen the pos-

sibility of operator injury. if normal safety

precautions are overlooked or ignored, seri-

ous personal injury may occur.

-8-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTiON 2: CiRCuiT REQuiREMENTS

110v Operation

Electrocution or fire could

result if this machine is

not grounded correctly or

if your electrical configu-

Serious personal injury could occur if you

ration does not comply

connect the machine to the power source

with local and state codes.

before you have completed the set up pro-

Ensure compliance by

cess. DO NOT connect the machine to the

checking with a qualified

power source until instructed to do so.

electrician!

Amperage Draw

the model h8259 motor draws the following amps

under maximum load:

motor draw..............................................7 amps

Circuit Recommendations

We recommend connecting your machine to a

dedicated and grounded circuit that is rated for

the amperage given below. never replace a circuit

breaker on an existing circuit with one of higher

amperage without consulting a qualiﬁed electri-

cian to ensure compliance with wiring codes. if

you are unsure about the wiring codes in your

area or you plan to connect your machine to a

shared circuit, consult a qualified electrician.

This machine must have a ground prong

in the plug to ground it. DO NOT remove

110v Circuit...........................................15 amps

ground prong from plug to fit into a two-

pronged outlet! if the plug will not fit the

outlet, have the proper outlet installed by a

qualified electrician.

Plug/Receptacle Type

included plug type........................... nema 5-15

Extension Cords

We do not recommend the use of extension cords,

but if you find it absolutely necessary:

Grounding Prong is

Longest of the Three

Prongs

•

use at least a 14 gauge cord that does not

exceed 50 feet in length!

the extension cord must also contain a

ground wire and plug pin.

Current

Carrying Prongs

Grounded

Outlet

a qualified electrician must size cords over

50 feet long to prevent motor damage.

figure 2. typical type 5-15 plug and receptacle.

-9-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTiON 3: SETuP

Set up Safety

unpacking

the model h8259 was carefully packed when it

left our warehouse. if you discover the machine

is damaged after you have signed for delivery,

please immediately call Customer Service at

(570) 546-9663 for advice.

This machine presents

serious injury hazards

to untrained users. Read

through this entire manu-

al to become familiar with

the controls and opera-

tions before starting the

machine!

save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

Wear safety glasses dur-

ing the entire setup pro-

cess!

inventory

after all the parts have been removed from the

box, you should have the following items:

Box Contents: (figure 3)

Qty

The Model H8259 is a

heavy machine. DO NOT

over-exert yourself while

unpacking or moving

your machine—get assis-

tance.

A. 10" x 18" benchtop lathe (not shown) ..... 1

B. live Center mt#2....................................... 1

C. spur Center mt#2...................................... 1

D. Quill handwheel Crank .............................. 1

E. hex Wrenches 3, 6, 8mm .................1 each

figure 3. box contents.

if any nonproprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them, or

for the sake of expediency, replacements can be

obtained at your local hardware store.

-10-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Clean up

Site Considerations

the unpainted surfaces are coated with a waxy

oil to prevent corrosion during shipment. remove

this protective coating with a solvent cleaner or

degreaser, such as shown in figure 4. For thor-

ough cleaning, some parts must be removed.

for optimum performance, clean all moving

parts or sliding contact surfaces. avoid chlo-

rine-based solvents, such as acetone or brake

parts cleaner that may damage painted surfac-

es. always follow the manufacturer’s instructions

when using any type of cleaning product.

Workbench Load

refer to the Machine Data Sheet for the weight

and footprint specifications of your machine.

some workbenches may require additional rein-

forcement to support both the machine and the

workpiece.

Placement Location

Consider existing and anticipated needs, size of

material to be processed through each machine,

and space for auxiliary stands, work tables or

other machinery when establishing a location for

your new machine. see figure 5 for the minimum

working clearances.

gasoline and petroleum

products have low flash

points and can explode

or cause fire if used to

clean machinery. DO

NOT use these products

to clean the machinery.

15"

16"

Many cleaning solvents

are toxic if inhaled.

Minimize your risk by only

using these products in a

well ventilated area.

36"

figure 5. minimum working clearances.

g2544—Solvent Cleaner & Degreaser

H9692—Orange Power Degreaser

great products for removing shipping grease.

Children and visitors may be

seriously injured if unsuper-

vised around this machine.

Lock entrances to the shop

or disable start switch or

power connection to prevent

unsupervised use.

figure 4. Cleaner/degreasers available from

grizzly.

-11-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Assembly

Test Run

before use, the tool rest must be moved out of

its shipping position and the quill handwheel

knob must be attached.

once the assembly is complete, test run your

machine to make sure it runs properly and is

ready for regular operation.

the test run consists of verifying the following:

1) the motor powers up and runs correctly.

2) the safety paddle switch works correctly.

To assemble the lathe:

1. loosen the release lever and rotate the tool

rest base away from the lathe bed.

if, during the test run, you cannot easily locate

the source of an unusual noise or vibration, stop

using the machine immediately, then review the

Troubleshooting on Page 26. if you still cannot

remedy a problem, contact our tech support at

(570) 546-9663 for assistance.

2. loosen the tool rest lock handle and rotate

the tool rest so that it is positioned parallel to

the lathe bed (figure 6).

3. tighten the tool rest lock handle.

To test run the machine:

tool rest

lock handle

1. make sure that you have read the safety

instructions at the beginning of this manual

and that the machine is setup properly.

2. Connect the machine to the power source.

3. turn the machine ON. make sure that your

hand stays poised over the switch in case

you need to quickly turn the machine OFF.

release

lever

tool rest

base

—When operating correctly, the machine

runs smoothly with little or no vibration or

rubbing noises.

figure 6. tool rest positioned.

—investigate and correct strange or unusual

noises or vibrations before operating the

machine further. always disconnect the

machine from power before investigating

or correcting potential problems.

4. secure the crank to the quill handwheel

(figure 7).

Quill

handwheel

4. turn the machine OFF.

5. remove the safety key and attempt to turn

the machine ON.

Crank

—if the machine starts, stop it and disconnect

it from power. the switch disabling feature

is not working. this safety feature must

work properly before proceeding. Call tech

support for help.

—if the machine does not start, the switch

disabling feature is working.

figure 7. Quill handwheel crank installed.

-12-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTiON 4: OPERATiONS

Operation Safety

Changing Speeds

to change speeds, the belt in the headstock must

be adjusted. a chart on the rear of the lathe bed

shows the belt positions needed to make the

lathe run at the desired speed.

Damage to your eyes, lungs, and ears could

result from using this machine without

proper protective gear. Always wear a face

shield, respirator, and hearing protection

when operating this machine.

To change speeds:

1. unplug the lathe From poWer!

2. loosen the belt tension screw and motor

mount screw (figures 8 & 9). be sure the

belt tension lever moves freely to release ten-

sion from the belt .

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving

machinery.

NOTICE

belt tension screw

belt tension lever

if you have never used this type of machine

or equipment before, WE STRONgLy REC-

OMMEND that you read books, trade maga-

zines, or get formal training before begin-

ning any projects. Regardless of the con-

tent in this section, grizzly industrial will

not be held liable for accidents caused by

lack of training.

figure 8. belt tension lever.

motor mount screw

figure 9. motor mount screw location.

-13-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

3. open the side and rear access covers (figure

10).

5. move the belt tension lever down, adjusting

tension so that ½" of belt deflection is mea-

sured as shown in figure 12, then tighten

belt tension lever screw.

rear access Cover

Pulley

Deflection

side access

Cover Knob

side access

Cover

figure 10. side and rear access covers.

Pulley

4. locate the desired speed on the speed chart

on the rear of the lathe bed, and move the

belt to the desired grooves on the motor and

spindle pulleys.

figure 12. belt deflection.

6. tighten the motor mount screw.

7. replace the rear and side covers and tighten

the cover knobs.

for Example: as indicated in the speed

chart, belt position B creates 1960 RPM

(figure 11).

POSITION

RPM

3337

2422

1713

1205

826

Motor Pulley

figure 11. h8259 spindle speeds.

-14-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting Tailstock

Adjusting Tool Rest

the tailstock is equipped with a cam-action

clamping system to secure it to the lathe bed.

When the lever is tightened, a locking plate lifts

and secures the tailstock to the bed.

the tool rest base is equipped with a cam-action

clamping system to secure it to the lathe bed.

When the lever is engaged, a locking plate lifts up

and secures the tool rest base to the bed.

To position the tailstock along the bed:

To position the tool rest base along the bed:

1. loosen the release lever and move the

tailstock to the desired position (figure 13).

1. loosen the release lever and slide the tool

rest base along the bed (figure 14).

lock handle

tool rest

base

lathe bed

release

lever

release

lever

lathe bed

figure 14. tool rest controls.

figure 13. tailstock controls.

2. re-engage the release lever to lock the tool

rest base in place.

2. re-engage the release lever.

3. if the release lever will not lock or release the

tailstock (either too loose or too tight), loosen

or tighten the tailstock mounting nut (located

on the underside of the tailstock) in small

increments as needed to achieve the proper

clamping pressure.

—if the release lever will not lock or

release(either too loose or too tight), then

loosen or tighten the tool rest base mount-

ing nut (located on the underside of the tool

rest base) in small increments as needed

to achieve the proper clamping pressure.

To adjust the tool rest:

1. loosen the lock handle (figure 14) and

adjust the tool rest vertically or swivel it as

needed, then tighten the lock handle.

-15-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

To remove the spur center:

installing/Removing

Spur Center

1. unplug lathe From poWer!

2. hold the headstock spindle wheel securely

while turning the faceplate counterclockwise

until the spur center is forced out of the head-

stock spindle (figure 16).

the spur center installs into the headstock spin-

dle with a taper fit.

To install the spur center:

Faceplate

1. unplug lathe From poWer!

2. insert the tapered end of the center into the

spindle, and push it in quickly and firmly

(figure 15).

headstock

spindle Wheel

spur Center

figure 16. removing spur center.

Note: If the lathe is used with the faceplate

removed, a knockout tool (not included) is

required for removing the spur center.

headstock

spindle Wheel

spur Center

figure 15. inserting spur center into spindle.

installing/Removing

Live Center

3. Check that the center is securely installed

by giving it a quick tug. (a properly installed

center will not pull out by hand.)

To install the live center:

1. loosen the quill lock handle (if locked)

approximately half a turn counterclockwise.

2. rotate the quill handwheel clockwise until the

tailstock quill protrudes out of the tailstock

housing about ⁄4''.

3. insert the live center, as shown in figure 17,

and push firmly.

-16-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Quill lock handle

Removing/installing

Quill

faceplate

To remove faceplate:

1. unplug lathe From poWer!

Quill

handwheel

2. hold the headstock spindle wheel securely

while turning the faceplate counterclockwise

until it is removed. if the spur center is

installed, it will be removed during this pro-

cess.

live Center

figure 17. installing live center in tailstock.

4. tighten the quill lock handle.

Faceplate

To remove the live center:

1. loosen the quill lock handle (if locked)

approximately half a turn counterclockwise.

headstock

spindle wheel

2. turn the quill handwheel counterclockwise

until the tailstock quill bottoms out, causing

the live center to be forced out of the quill.

figure 18. removing faceplate.

To install faceplate:

The tailstock quill lock handle must always

be locked down while the lathe is in use. The

workpiece can be thrown from the lathe if

this step is not observed. Also, the tailstock

quill should not protrude from the tailstock

housing more than 2'' or the quill will not be

supported enough. failure to follow these

warnings may result in personal injury.

1. unplug lathe From poWer!

2. thread faceplate onto spindle shaft until it is

secure against the shoulder on the spindle

shaft.

to mount a workpiece to your faceplate, refer to

Page 20.

-17-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Scrapers—mainly used where access for

other tools is limited, such as hollowing oper-

ations. this is a flat, double-ground tool that

comes in a variety of profiles (round nose,

spear point, square nose, etc.) to match

many different contours. figure 21 shows an

example of a round nose scraper.

Selecting Turning

Tools

lathe tools come in a variety of shapes and sizes

and usually fall into five major categories.

•

gouges—mainly used for rough cutting,

detail cutting, and cove profiles. the rough

gouge is a hollow, double-ground tool with

a round nose, and the detail gouge is a hol-

low, double-ground tool with either a round or

pointed nose. figure 19 shows an example

of a gouge.

figure 21. round nose scraper.

•

Parting Tools—used for sizing and cut-

ting off work. this is a flat tool with a sharp

pointed nose that may be single- or double-

ground. figure 22 shows an example of a

parting tool.

figure 19. gouge.

•

Skew Chisel—a very versatile tool that can

be used for planing, squaring, v-cutting,

beading, and parting off. the skew chisel

is flat, double-ground with one side higher

than the other (usually at an angle of 20-

40˚). figure 20 shows an example of a skew

chisel.

figure 22. parting tool.

•

Specialty Tools—these are the unique,

special function tools to aid in hollowing, bowl

making, cutting profiles, etc. the swan neck

hollowing tool shown on Page 23 is a good

example of a specialty tool.

figure 20. skew chisel.

-18-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

2. using a wood mallet, tap the point of the spur

center into the center of the workpiece, so

that it leaves a center mark, then remove the

spur center.

Spindle Turning

spindle turning (figure 23) is the operation per-

formed when a workpiece is mounted between

the headstock and the tailstock.

3. using a ¹⁄8" drill bit, drill a ³⁄16" deep hole at the

center mark.

4. Cut the corners off your workpiece if it is over

2" x 2" to make turning safer and easier.

5. drive the spur center into the center of the

workpiece with a wood mallet to embed it at

least ⁄4", as shown in figure 25.

1/4"

typical spindle turning operation.

figure 23.

To set up a spindle turning operation:

1. mark both ends of your workpiece by draw-

ing diagonal lines from corner to corner. the

intersection point of these lines will show you

the center of your workpiece. see figure 24

for details.

figure 25. spur center properly embedded.

6. With the workpiece still attached, insert the

spur center into the headstock spindle.

7. With the live center installed in the tailstock,

slide the tailstock toward the workpiece until

the live center touches the workpiece center-

point, then lock the tailstock in this position.

Workpiece

Pencil Lines

Marked Diagonally

Across Corners

8. use the quill handwheel to push the live cen-

ter into the workpiece at least ⁄4".

Do not press the workpiece too firmly with

the tailstock or the bearings will bind and

overheat. Likewise, do not leave it too loose

or the workpiece will spin off the lathe. use

good judgement. Serious personal injury

could result if care is not taken.

Workpiece

Center

figure 24. Workpiece marked diagonally from

corner to corner to determine the center.

-19-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

9. position the tool rest approximately ⁄4" away

•

turn the lathe OFF immediately if the

workpiece vibrates excessively. Check to

make sure the workpiece is centered and

balanced. remove the workpiece and trim

excess waste off corners with a bandsaw or

table saw to reduce vibration. make sure the

workpiece is securely attached in the setup.

from the workpiece and approximately ⁄8

above the center line, as shown in figure

26.

Workpiece

faceplate Turning

/4"

Distances

/8"

Center Line

Faceplate turning (figure 27) is when a workpiece

is mounted to the faceplate, which is mounted to

the headstock spindle. this type of turning is usu-

ally done with open-faced workpieces like bowls.

Tool Rest

if screws cannot be placed in the workpiece, then

a backing block can be glued to the workpiece

and attached to the faceplate with screws.

figure 26. tool rest position.

10. test the setup by hand-turning the workpiece

to make sure there is enough clearance all

the way around before starting.

Spindle Turning Tips:

•

When turning the lathe ON, stand to the side

of the spinning direction until the lathe reach-

es full speed and you can verify that the lathe

will not throw the workpiece.

•

use the slowest spindle speed when rough

cutting.

select the right speed for the size of workpiece

you are turning. use slower speeds for

large workpieces (4" diameter and over); use

the middle range speeds for medium sized

workpieces (2" to 4" diameter); and use faster

speeds for small sized workpieces (under 2"

in diameter).

figure 27. typical faceplate turning operation.

To mount your workpiece to the faceplate:

1. Find the center of your workpiece in the same

manner as when spindle turning.

2. Cut off the corners of the workpiece.

•

Keep the turning tool on the tool rest the

entire time that it is in contact with the

workpiece.

3. Center the faceplate on the workpiece and

attach it through the faceplate holes with

non-tapered head wood screws as shown in

Figure 28.

learn the correct techniques for each tool

you will use. if you are unsure, read books or

magazines about lathe techniques and seek

training from experienced users.

4. thread the faceplate onto the headstock

spindle and tighten securely.

-20-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTiCE: Only use tap screws or wood screws

with non-tapered heads (Figure 28) to attach the

faceplate to the workpiece. Do NOT use drywall

screws or screws with tapered heads because

these can split the faceplate, or the screws may

snap off during operation.

Sanding/finishing

after turning, the workpiece can be sanded, as

shown in figure 30, and finished (in the same

manner) before removing it from the lathe.

figure 28. Correct and incorrect screw types for

mounting faceplate to workpiece.

To mount your workpiece to a backing block:

1. make the backing block (figure 29) from

a piece of scrap wood that is flat on both

sides.

figure 30. typical sanding operation.

Sandpaper

Wrapping the sandpa-

per completely around

the workpiece will pull

your hands into the mov-

ing workpiece and may

cause injury. Never wrap

sandpaper completely

backing

block

Workpiece

around the workpiece!

Whenever sanding or finishing, move the tool rest

holder out of the way to increase personal safety

and gain adequate working room.

figure 29. example of mounting faceplate to a

backing block.

2. locate and mark the center of both the

workpiece and the backing block.

3. drill a ¹⁄4" diameter hole through the center of

the backing block.

4. glue the center of the backing block to the

center of the workpiece (look through the

drilled hole to line up centers), clamp the

backing block to the workpiece, and wait for

the glue to cure according to the manufactur-

er’s recommendation.

-21-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

aCCessories

SECTiON 5: ACCESSORiES

g1194—3-Jaw Chuck

H7828—Tool Table Plus

a "must have" for the serious wood turner. this

3-jaw chuck is a self-centering style chuck used

mostly for round work. all three jaws tighten

together at the same time. Jaws are reversible for

expanded work holding capacity. Threaded insert

required for mounting!

the new tool table plus was designed in response

to customer requests for a slightly wider and

taller table to accommodate small planers, wood

lathes, sanders and a variety of other bench-top

machines.

figure 33. model h7828 tool table plus.

figure 31. model g1194 3-Jaw Chuck.

H6542—Robert Sorby HSS 8-PC Turning Set

g1676—Drill Chuck Arbor MT#2 x JT#3

H6204—Precision Drill Chuck ¹⁄32"–⁵⁄8" x JT#3

H3102, H3103, H3104—gouge Slipstones

H1064—6-PC Deluxe HSS Lathe Chisel Set

g9863—8-PC HSS Lathe Chisel Set

g1082—4-Jaw Chuck

another "must have" for the serious wood turner.

this 4-jaw chuck is an independent type chuck

that is used for square and odd-shaped pieces.

each jaw tightens individually and can be turned

around to hold larger dimension workpieces.

Threaded insert required for mounting!

H0507—20" Swan Neck Hollowing Tool

H0508—24" Swan Neck Hollowing Tool

figure 32. model g1082 4-Jaw Chuck.

figure 34. model h6542 robert sorby 8-pC set.

model h8259 mfg. 10/07+

g3163—1" x 8 TPi RH Threaded insert.

this threaded insert is required to mount a 3- or

4-jaw chuck to your wood lathe.

-22-

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTiON 6: MAiNTENANCE

unpainted Cast iron

Always disconnect power

to the machine before

performing maintenance.

failure to do this may

result in serious person-

protect the unpainted cast iron surfaces on the

lathe by wiping them clean after every use—this

ensures moisture from wood dust does not remain

on bare metal surfaces.

al injury.

Keep the bed rust-free with regular applications

of products like g96^®gun treatment, slipit^®, or

boeshield^®t-9.

Schedule

For optimum performance from your machine,

follow this maintenance schedule and refer to any

specific instructions given in this section.

Lubrication

lubricate the locations shown in figure 35 with

light machine oil or g96^®gun treatment.

Daily Check:

•

loose mounting bolts.

Worn or damaged wires.

Worn switch

any other unsafe condition.

Monthly Check:

•

belt tension, damage, or wear.

•

Clean/vacuum dust buildup off of motor.

Cleaning

Cleaning the model h8259 is relatively easy.

vacuum excess wood chips and sawdust, and

wipe off the remaining dust with a dry cloth. if any

resin has built up, use a resin dissolving cleaner

to remove it. treat all unpainted cast iron and steel

with a non-staining lubricant after cleaning.

figure 35. lubrication locations.

-23-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

5. tap the spindle far enough out of the head-

stock so that the belt can be removed. a rub-

ber or wooden mallet may be required. take

care not to damage the spindle threads.

Changing Belt

To remove the old belt:

To install new belt:

1. open the side and rear access covers as

shown in Steps 1-5 in the Changing Speeds

procedure on Page 13.

1. place the new belt over the spindle pulley.

2. slide the spindle back through the headstock

and into the original position. a mallet may be

required.

2. roll the belt off of the motor (lower) pulley

(figure 36).

3. install the headlock spindle wheel and tighten

both set screws.

belt (released)

4. loosely install the belt on the motor pulley

in one of the five available positions, making

sure to leave access to the pulley set screw.

5. adjust the spindle pulley position on the

spindle shaft to ensure proper belt alignment

(figure 38).

motor pulley

Correct alignment

figure 36. belt removed from lower pulley.

3. loosen both set screws on the headstock

spindle wheel (figure 37) and turn it clock-

wise to unthread and remove it.

4. loosen the set screw on the spindle pulley

through the rear cover access until the pulley

spins freely on the spindle (refer to figure 37

for set screw locations).

incorrect alignment

figure 38. proper belt alignment.

6. rotate the spindle pulley on the spindle shaft

until the set screw aligns with the keyway on

the spindle shaft, then tighten the set screw.

7. Complete the new belt installation by follow-

ing Steps 6-9 in the Changing Speeds pro-

cedure on Page 14.

pulley set screw

headstock spindle

Wheel set screw (2)

figure 37. set screw locations.

-24-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTiON 7: SERviCE

review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-

ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical

support at (570) 546-9663.

Troubleshooting

Motor & Electrical

symptom

possible Cause

possible solution

machine does not 1. plug/receptacle is at fault or wired incor- 1. test for good contacts; correct the wiring.

start or a breaker

trips.

rectly.

2. power supply is at fault/switched OFF.

2. ensure hot lines have correct voltage on all legs and

main power supply is switched ON.

3. lockout key is at fault.

3. install/replace lockout key; replace switch.

4. motor on button or on/oFF switch is at 4. replace faulty on button or on/oFF switch.

fault.

5. Wiring is at fault.

5. Check for broken wires or disconnected/corroded

connections, and repair/replace as necessary.

6. test/repair/replace.

6. motor is at fault.

machine stalls or is 1. plug/receptacle is at fault.

1. test for good contacts; correct the wiring.

2. test by rotating shaft; rotational grinding/loose shaft

requires bearing replacement.

underpowered.

2. motor bearings are at fault.

3. motor has overheated.

4. motor is at fault.

3. Clean off motor, let cool, and reduce workload.

4. test/repair/replace.

machine has vibra- 1. motor or component is loose.

tion or noisy opera-

1. inspect/replace stripped or damaged bolts/nuts, and

re-tighten with thread locking fluid.

tion.

2. motor fan is rubbing on fan cover.

2. replace dented fan cover; replace loose/damaged

fan.

3. Workpiece or chuck is at fault.

4. motor bearings are at fault.

3. Center workpiece in chuck or face plate; reduce

rpm; replace defective chuck.

4. test by rotating shaft; rotational grinding/loose shaft

requires bearing replacement.

Wood Lathe Operation

symptom

possible Cause

possible solution

vibration noise

while machine

is running; noise

changes when

speed is changed.

1. belt cover loose.

1. tighten the belt cover lock handle; if necessary

install a soft, vibration dampening material (between

the belt cover and the headstock casting.

2. remove belt cover and inspect the inside for dents,

bends, or indications of rubbing. tap out the dent

with a rubber mallet, bend back into proper shape,

or shim belt cover away from the motor pulley.

2. belt cover bent or dented and is making

contact with the motor pulley or belt.

-25-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

symptom

possible Cause

possible solution

vibration noise

while machine

is running; noise

remains constant

when speed is

changed.

1. dented fan cover on motor.

1. replace or adjust fan cover. inspect motor fan and

replace if damaged.

motor is running but 1. belt is loose, broken, or has come off pul-

1. inspect belt and tighten, reinstall, or replace if dam-

aged.

spindle is not turn-

ing.

leys.

excessive vibration. 1. Workpiece mounted incorrectly.

1. re-mount workpiece, making sure that centers are

embedded in true center of workpiece.

2. Cut workpiece to correct, or use a different

workpiece.

2. Workpiece warped, out of round, or is

flawed.

3. spindle speed is set too fast for mounted

workpiece.

3. reduce the spindle speed.

4. lathe is resting on an uneven surface.

5. motor mount bolts are loose.

6. belt is worn or damaged.

7. spindle bearings are worn.

4. shim or adjust feet to remove any wobbles.

5. tighten motor mount bolts.

6. replace belt.

7. replace spindle bearings.

Chisels grab or dig

into workpiece.

1. tool rest set too low.

1. set tool rest higher. see Page 20 for how to prop-

erly set the tool rest height.

2. tool rest set too far from workpiece.

2. move the tool rest closer to the workpiece. see

Page 20 for the proper workpiece/tool rest clear-

ance.

3. Wrong chisel/tool being used.

3. use the correct chisel/tool; educate yourself by

reading books, trade magazines, or seeking help

from an experienced lathe operator.

4. Chisel/tool dull.

4. sharpen or replace the chisel/tool you are using.

bad surface finish.

tailstock moves.

1. Wrong spindle speed.

2. dull chisel or wrong chisel being used for

the operation.

1. use trial-and-error to find a better spindle speed.

2. sharpen chisel or try a different chisel.

1. tailstock mounting bolt loose.

2. too much clamping pressure applied by

tailstock.

1. tighten.

2. apply less clamping pressure with tailstock.

3. bed surface is oily or greasy.

3. Clean bed surface to remove oil/grease.

Can't remove

tapered tool from

tailstock barrel.

1. tailstock barrel had not retracted all the

way back into the tailstock.

2. debris was not removed from taper before

inserting into barrel.

1. turn the barrel handwheel until it forces taper out of

barrel.

2. always make sure that taper surfaces are clean.

-26-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

H8259 Wiring Diagram

View this page in color at

www.grizzly.com.

PADDLE SWITCH

(viewed from behind)

110

VAC

Green

Ground

White

Neutral

5-15 Plug

Black

Hot

Ground

Start

Capacitor

24MFD

300VAC

MOTOR

figure 40. switch connections.

figure 39. motor connections.

-27-

model h8259 mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Breakdown

-28-

Model H8259 Mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Breakdown Parts List

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

PH8259001

PSB64M

LATHE BED

CAP SCREW M10-1.5 X 25

RETAINING PLATE

QUILL HANDWHEEL

TAILSTOCK

QUILL LOCK LEVER

TAILSTOCK LOCK LEVER

TAILSTOCK QUILL

LIVE CENTER TAPER ROD

BALL BEARING 6002ZZ

LIVE CENTER

SPUR CENTER

FACEPLATE

HEADSTOCK SPINDLE

BALL BEARING 6005ZZ

INT RETAINING RING 47MM

HEADSTOCK

REAR ACCESS COVER

HEADSTOCK HANDWHEEL

DRIVE PULLEY

ULTRA-FLEX BELT 7 X 4 x 625

CAP SCREW M8-1.25 X 30

SET SCREW M6-1 X 12

MOTOR PULLEY

CAP SCREW M6-1 X 15

MOTOR PLATE

PSB14M

PR47M

CAP SCREW M8-1.25 X 20

EXT RETAINING RING 13MM

TOOL REST

TOOL REST BASE

TOOL REST ADJUST SHAFT

SLIDE COLLAR

PH8259003

PH8259004

PH8259005

PH8259006

PH8259007

PH8259008

PH8259009

P6002

PH8259011

PH8259012

PH8259013

PH8259014

P6005

PH8259035

PH8259036

PH8259037

PH8259038

PLN05M

PH8259040

PH8259041

PH8259042

PH8259043

PLN04M

PH8259045

PH8259046

PW01M

PLW04M

PH8259050

PW01M

LOCK NUT M10-1.5

TOOLREST BASE RELEASE LEVER

TOOLREST LOCK LEVER

TAILSTOCK ADJUST SHAFT

SLIDE COLLAR

LOCK NUT M8-1.25

POWER CORD

SWITCH W/SAFETY KEY

FLAT WASHER 8MM

LOCK WASHER 8MM

RUBBER FOOT

PR25M

PH8259019

PH8259020

PH8259022

PH8259025

PH8259026

PSB13M

PSS04M

PH8259029

PSB28M

FLAT WASHER 8MM

PR01M

EXT RETAINING RING 10MM

TAP SCREW M4 X 25

LOCKING KNOB M5-.8 X 10

KNOB HANDLE

SIDE ACCESS COVER

FLAT HD SCR M5-.8 X 15

SHOULDER SCREW M5-.8 X 10

QUILL CRANK HANDLE

HEX WRENCH 3MM

PHTEK28M

PH8259055

PH8259056

PH8259057

PFH01M

PH8259059

PH8259060

PAW03M

PH8259031

PH8259032

MOTOR (1/2HP 110V 1750RPM)

32-1 PH8259032-1 FAN COVER

32-2 PH8259032-2 FAN

32-3 PH8259032-3 CAPACITOR COVER

32-4 PH8259032-4 CAPACITOR 24M 300V 35 X 65MM

PAW06M

PAW08M

PH8259064

HEX WRENCH 6MM

HEX WRENCH 8MM

TAILSTOCK LEADSCREW M16-2 X 60 (LH)

-29-

Model H8259 Mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning Labels Breakdown & Parts List

101

102

103

105

104

106

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

101

102

103

PH8259101

PLABEL-14

PH8259103

ENTANGLEMENT HAZARD LABEL

ELECTRICITY LABEL

104

105

106

PH8259104

PH8259105

PH8259106

READ MANUAL LABEL

MACHINE ID LABEL

FACE SHIELD LABEL

SPINDLE SPEEDS LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine

MUST maintain the original location and readability of the labels on the machine. If any label is

removed or becomes unreadable, REPLACE that label before using the machine again. Contact

Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-30-

Model H8259 Mfg. 10/07+

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY CARD

Name_____________________________________________________________________________

Street_____________________________________________________________________________

City _______________________ State_________________________ Zip _____________________

Phone #____________________ Email ________________________ Invoice #_________________

Model # ____________________ Order #_______________________ Serial #__________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop

better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

____ Advertisement

____ Card Deck

____ Friend

____ Website

____ Catalog

____ Other:

2. Which of the following magazines do you subscribe to?

____ Cabinet Maker

____ Family Handyman

____ Hand Loader

____ Popular Mechanics

____ Popular Science

____ Popular Woodworking

____ Practical Homeowner

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Today’s Homeowner

____ Wood

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Handy

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Model Airplane News

____ Modeltec

____ Woodwork

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ Riﬂe

____ Shop Notes

____ Old House Journal

____ Shotgun News

3. What is your annual household income?

____ $20,000-$29,000

____ $30,000-$39,000

____ $40,000-$49,000

____ $70,000+

____ $50,000-$59,000

____ $60,000-$69,000

4. What is your age group?

____ 20-29

____ 30-39

____ 60-69

____ 40-49

____ 70+

____ 50-59

5. How long have you been a woodworker/metalworker?

____ 0-2 Years ____ 2-8 Years

____ 8-20 Years

____20+ Years

____10+

6. How many of your machines or tools are Grizzly?

____ 0-2 ____ 3-5

____ 6-9

7. Do you think your machine represents a good value?

8. Would you recommend Grizzly Industrial to a friend?

_____Yes

_____No

9. Would you allow us to use your name as a reference for Grizzly customers in your area?

Note: We never use names more than 3 times. _____Yes _____No

10. Comments:_____________________________________________________________________

_________________________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

FOLD ALONG DOTTED LINE

Place

Stamp

Here

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTy AND RETuRNS

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then

issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the

carton. We will not accept any item back without this number. Proof of purchase must accompany the

merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

Download from Www.Somanuals.com. All Manuals Search And Download.

Buy Direct and Save with Grizzly^®– Trusted, Proven and a Great Value!

~Since 1983~

Visit Our Website Today For

Current Specials!

ORDER

24 HOURS A DAY!

1-800-523-4777

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Car Seat PD238261A User Manual
Greenheck Fan Ventilation Hood CW CWB User Manual
Haier Washer HWMP75 918 User Manual
Haier Washer XPB80 35 User Manual
Harmar Mobility Automobile Accessories AL001 User Manual
Hasselblad Camera Lens HC 35 35 User Manual
Honeywell Thermostat CG510A User Manual
Hoshizaki Automobile Alarm KMS 1400MLH User Manual
Icom Car Amplifier iPW1 User Manual
Image Treadmill IMTL12900 User Manual