MODEL H7779
JERKY SLICER
INSTRUCTION SHEET
Inventory (Figure 1)
Disassembly for Cleaning
You must disassemble the jerky slicer as shown
in Figure 2 to clean all individual components
thoroughly. Disassembly requires a 5mm hex
wrench to remove the top half of the jerky slicer.
A. Jerky Slicer................................................. 1
B. Handle........................................................ 1
C. Thumbscrew for Handle............................. 1
D. Clamps ....................................................... 2
E. Meat Alignment Combs.............................. 2
You MUST clean, thoroughly rinse, and sani-
tize all components of this product BEFORE
and BETWEEN uses. Failure to follow this
warning may lead to sickness or death!
A
Figure 2. Required level of disassembly for
proper cleaning of all components.
C
B
When removing the crank arm shaft, be aware
that the end is spring loaded (see Figure 3).
D
E
This End Spring Loaded
Figure 1. Model H7779 inventory.
NOTICE
The Model H7779 is NOT dishwasher safe!
Figure 3. Overhead view of blade shafts.
COPYRIGHT © NOVEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR7699 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
1. Assemble the blade shafts as shown in
Figure 3. When assembled correctly, the
spring pushes the flat parts of the blades
together. When replacing the blades on the
main shaft (the one connected to the crank
handle), make sure the beveled edge of the
blades are facing the spring side. On the
driven shaft, make sure the beveled sides of
the blades are facing the gear side.
2. Fasten the top half of the jerky slicer onto the
base with the two cap screws.
Figure 4. Inserting comb.
3. Install the crank handle and secure it in place
with the thumbscrew.
4. Insert the meat alignment combs into each
side of the slicer, as shown in Figure 4.
5. Clamp the jerky slicer to the counter or table
as shown in Figure 5. The maximum counter
thickness that will work with the provided
1
clamps is 1 ⁄2
"
If you need additional help with this assembly, call
our Tech Support at: (570) 546-9663.
Operating
Figure 5. Jerky slicer clamped to counter.
This jerky slicer will accept pieces of meat up to
1" thick and up to 43⁄4" wide. Cut larger pieces to
fit before trying to insert them into the slicer. If you
wedge too large of piece into the slicer, it may
get stuck or place undue pressure on the cutting
components.
Make your kitchen “child
safe.” Ensure that the jerky
slicer is inaccessible to chil-
dren by storing out-of-reach
or locking it away. Never
allow children to use this
jerky slicer without the direct
supervision of a responsible
adult.
To slice meat, insert the piece of meat into the
opening and turn the handwheel. NEVER INSERT
FINGERS INTO THE OPENING! If a piece of
meat becomes stuck, use a fork to remove it or
remove the top for easier access.
If you intend to slice different kinds of meat
at the same time, clean the slicer between
meat types to avoid cross contamination.
Download from Www.Somanuals.com. All Manuals Search And Download.
H7779 Parts Breakdown and List
�
�
�
�
�
�
�
�
��
��
��
��
��
�
��
��
��
�
�
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH7779001 FUNNEL
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
PH7779017 CLAMP
2
PH7779002 STAINLESS CAP SCREW M6-1 X 12
PH7779003 STAINLESS FLAT WASHER 6MM
PH7779004 UPPER HOUSING
PH7779018 STAINLESS CAP SCREW M6-1 X 10
PH7779019 GEAR ASSEMBLY
3
4
PH7779020 PLASTIC GEAR BUSHING 13MM
PH7779021 SPECIAL STAINLESS WASHER 13MM
5
PH7779005 STAINLESS PHLP HD SCR M5-.8 X 16
PH7779006 COMB
6
PR47M
EXT RETAINING RING 13MM
7
PH7779007 DRIVEN SHAFT
PH7779023 PLASTIC BUSHING 30MM
PH7779024 PLASTIC BUSHING 29MM
PH7779025 PLASTIC BUSHING 25MM
PH7779026 COMPRESSION SPRING
PH7779027 BUSHING CAP
8
PH7779008 MAIN SHAFT
9
PH7779009 CRANK HANDLE
10
11
12
13
14
15
16
PH7779010 HANDLE THUMB SCREW
PH7779011 STAINLESS CAP SCREW M6-1 X 8
PH7779012 RIGHT LEG
PH7779028 DRIVEN SHAFT BUSHING
PH7779029 MAIN SHAFT BUSHING
PH7779030 BLADE
PH7779013 BASE
PH7779014 STAINLESS CAP SCREW M5-.8 X 10
PH7779015 LEFT LEG
PH7779031 PLASTIC BUSHING 40MM
PH7779016 LOWER HOUSING
Download from Www.Somanuals.com. All Manuals Search And Download.
|