1 HP CANISTER
DUST COLLECTOR
MODEL G0583
INSTRUCTION MANUAL
COPYRIGHT © JANUARY, 2005 BY GRIZZLY INDUSTRIAL, INC.; UPDATED SEPTEMBER, 2005.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#CR6902 PRINTED IN TAIWAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION............................................................................................................................... 2
Foreword .................................................................................................................................... 2
Contact Info................................................................................................................................ 2
Identification ............................................................................................................................... 4
SECTION 1: SAFETY....................................................................................................................... 5
Additional Safety for Canister Dust Collectors........................................................................... 7
SECTION 2: CIRCUIT REQUIREMENTS ........................................................................................ 8
110/220V Operation................................................................................................................... 8
SECTION 3: SET UP...................................................................................................................... 10
Unpacking ................................................................................................................................ 10
Inventory................................................................................................................................... 10
Site Considerations.................................................................................................................. 11
Hardware Recognition Chart.................................................................................................... 12
Base and Supports................................................................................................................... 13
Canister Filter........................................................................................................................... 14
Collection Bag.......................................................................................................................... 15
SECTION 4: COLLECTION SYSTEM............................................................................................ 16
General..................................................................................................................................... 16
Material Selection..................................................................................................................... 16
SECTION 5: OPERATION.............................................................................................................. 20
Operation Safety ...................................................................................................................... 20
Test Run................................................................................................................................... 20
General..................................................................................................................................... 20
SECTION 6: MAINTENANCE ........................................................................................................ 21
Schedule .................................................................................................................................. 21
Lubrication................................................................................................................................ 21
Bag and Canister Cleaning...................................................................................................... 21
G0583 Parts Breakdown.......................................................................................................... 24
Canister Breakdown................................................................................................................. 25
Parts List .................................................................................................................................. 26
Accessories.............................................................................................................................. 27
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Contact Info
Foreword
If you have any comments or criticisms that
you feel we should address in our next printing,
please write to us at:
Grizzly Industrial, Inc. is proud to offer the
Model G0583 1 HP Canister Dust Collector. This
machine is part of Grizzly’s growing family of fine
machinery. When used according to the guide-
lines stated in this manual, you can expect years
of trouble-free, enjoyable operation.
Grizzly Industrial, Inc.
C
⁄O
Technical Documentation
P.O. Box 2069
Bellingham, WA 98227
We are also pleased to provide this manual with
the Model G0583. It was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It repre-
sents our latest effort to produce the best docu-
mentation possible.
Most important, we stand behind our machines.
We have excellent regional service departments
at your disposal should the need arise.
If you have any service questions or parts
requests, please call or write to us at the location
listed below.
Grizzly Industrial, Inc
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone:(570) 546-9663
Fax:(800) 438-5901
E-Mail: [email protected]
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G0583 as supplied when the manual was pre-
pared. However, owing to Grizzly’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
For your convenience, we always keep current
Grizzly manuals available on our website at www.
grizzly.com. Any updates to your machine will be
reflected in these manuals as soon as they are
complete.
-2-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
MODEL G0583 1 HP CANISTER DUST COLLECTOR
Design Type ................................................................................. Single Stage Floor Model
Overall Dimensions:
Base ..............................................................................................................151⁄4" x 26"
Height..................................................................................................................... 585⁄8
"
Machine Size.......................................................................153⁄4" D x 303⁄4" L x 585⁄8" H
Shipping Weight (Machine).............................................................................. 59.4 lbs.
Shipping Weight (Canister) .............................................................................. 17.6 lbs.
Net Weight (Machine) ...................................................................................... 52.8 lbs.
Net Weight (Canister).......................................................................................... 13 lbs.
1st Box Size (Machine)........................................................ 283⁄4" L x 161⁄4" W x 181⁄8" H
2nd Box Size (Canister) ....................................................... 173⁄8" L x 173⁄8" W x 283⁄8" H
Specifications:
Intake Hole Size..........................................................................................................4"
Intake Adapter Hole Size .....................................................................4" Elbow Fitting
Canister Size.......................................................................... 141⁄2" Diameter x 235⁄8" H
Canister Material................................................. Wire Reinforced Pleated Filter Paper
Canister Filtration Rating............................................................................... 2.5 Micron
Storage Bag Size .......................................................................143⁄4" Diameter x 243⁄8
"
Storage Bag Material .......................................................................Heavy Duty Plastic
Storage Bag Capacity ............................................................................ 2.1 Cubic Feet
Air Suction Capacity (With 4" Elbow).............................................................. 630 CFM
Air Suction Capacity (Without 4" Elbow)......................................................... 800 CFM
Static Pressure (Inches of Water)............................................................................3.3"
Construction:
Base ...................................................................................... Sheet Metal with Casters
Body ........................................................................................................... Sheet Metal
Impeller Type .................................................................................................Radial Fin
Impeller Construction ............................................................. 3⁄32" Steel, 7 Riveted Fins
Impeller Size ...............................................................................................................9"
Motor:
Type ....................................................................................... TEFC (Aluminum finned)
Horsepower............................................................................................................1 HP
Phase / Voltage.........................................Single Phase 110V / 220V (Prewired 110V)
Amps ................................................................................................................. 9A/4.5A
Cycle/ RPM .................................................................................. 60 Hertz / 3450 RPM
Switch........................................................................................ On / Off Paddle Switch
Bearings ................................................................... Sealed & Permanently Lubricated
Specifications, while deemed accurate, are not guaranteed.
G0583 1 HP Canister Dust Collector
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
1
2
7
5
3
4
6
1. Canister Filter Cleaning Handle
2. Canister Filter
3. 4" Duct Elbow
4. Clear Dust Storage Bag
5. Power Switch w/ Safety Key
6. Roller Base
7. Handle
-4-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to
alert against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
1. READ THROUGH THE ENTIRE MANUAL
BEFORE STARTING MACHINERY.
Machinery presents serious injury hazards
to untrained users.
4. ALWAYS USE HEARING PROTECTION
WHEN OPERATING MACHINERY.
Machinery noise can cause permanent
hearing damage.
5. WEAR PROPER APPAREL. DO NOT
wear loose clothing, gloves, neckties, rings,
or jewelry which may get caught in moving
parts. Wear protective hair covering to con-
tain long hair and wear non-slip footwear.
2. ALWAYS USE ANSI APPROVED
SAFETY GLASSES WHEN OPERATING
MACHINERY. Everyday eyeglasses only
have impact resistant lenses, they are
NOT safety glasses.
6. NEVER OPERATE MACHINERY WHEN
TIRED, OR UNDER THE INFLUENCE OF
DRUGS OR ALCOHOL. Be mentally alert
at all times when running machinery.
3. ALWAYS WEAR AN ANSI APPROVED
RESPIRATOR WHEN OPERATING
MACHINERY THAT PRODUCES DUST.
Wood dust is a carcinogen and can cause
cancer and severe respiratory illnesses.
G0583 1 HP Canister Dust Collector
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions for Machinery
7. ONLY ALLOW TRAINED AND PROP-
16. MAKE SURE GUARDS ARE IN PLACE
ERLY SUPERVISED PERSONNEL TO
OPERATE MACHINERY. Make sure
operation instructions are safe and clearly
understood.
AND WORK CORRECTLY BEFORE
USING MACHINERY.
17. REMOVE ADJUSTING KEYS AND
WRENCHES. Make a habit of checking for
keys and adjusting wrenches before turn-
ing machinery ON.
8. KEEP CHILDREN AND VISITORS AWAY.
Keep all children and visitors a safe dis-
tance from the work area.
18. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY. Check
for binding and alignment of parts, broken
parts, part mounting, loose bolts, and any
other conditions that may affect machine
operation. Repair or replace damaged
parts.
9. MAKE WORKSHOP CHILD PROOF. Use
padlocks, master switches, and remove
start switch keys.
10. NEVER LEAVE WHEN MACHINE IS
RUNNING. Turn power OFF and allow all
moving parts to come to a complete stop
before leaving machine unattended.
19. USE RECOMMENDED ACCESSORIES.
Refer to the instruction manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury.
11. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use machin-
ery in damp, wet locations, or where any
flammable or noxious fumes may exist.
20. DO NOT FORCE MACHINERY. Work at
the speed for which the machine or acces-
sory was designed.
12. KEEP WORK AREA CLEAN AND WELL
LIT. Clutter and dark shadows may cause
accidents.
21. SECURE WORKPIECE. Use clamps or
a vise to hold the workpiece when practi-
cal. A secured workpiece protects your
hands and frees both hands to operate the
machine.
13. USE A GROUNDED EXTENSION CORD
RATEDFORTHEMACHINEAMPERAGE.
Undersized cords overheat and lose power.
Replace extension cords if they become
damaged. DO NOT use extension cords
for 220V machinery.
22. DO NOT OVERREACH. Keep proper foot-
ing and balance at all times.
23. MANY MACHINES WILL EJECT THE
WORKPIECETOWARDTHEOPERATOR.
Know and avoid conditions that cause the
workpiece to "kickback."
14. ALWAYS DISCONNECT FROM POWER
SOURCE
BEFORE
SERVICING
MACHINERY. Make sure switch is in OFF
position before reconnecting.
24. ALWAYS LOCK MOBILE BASES
15. MAINTAIN MACHINERY WITH CARE.
Keep blades sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.
BEFORE OPERATING MACHINERY.
-6-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety for Canister Dust Collectors
1. MACHINE USE. Do not use this dust col-
lector to pick up liquids and metal scrap
including, but not limited to, nails and fil-
ings. Metallic debris will contact the spin-
ning impeller and could spark. The spark
could then cause a sawdust explosion or
severe fire hazard. Also, do not pick up
material which cannot safely pass through
the impeller such as solid wood scraps.
6. AVOIDING FIRES. Do not allow steel to
strike against impeller which may produce
a spark. Sparks can smolder in wood dust
for a long time before fire or flame is detect-
ed. If metal contacts metal during opera-
tion, immediately turn off the dust collector,
unplug the power cord from the outlet or
flip the disconnect switch and wait for all
moving parts to stop. Remove collection
bags and empty the dust into an approved
air tight metal container in case of spark.
Remedy the metal to metal contact problem
before resuming operation.
2. KEEPING FINGERS SAFE. Do not place
your hands or tools near the open inlet dur-
ing operation for any reason including, but
not limited to, unclogging material and test-
ing suction. The impeller could cause seri-
ous damage to body parts if touched while
spinning.
7. OPERATIONAL QUESTIONS. If at any
time you are experiencing difficulties per-
forming the intended operation, stop using
the machine! Then contact our service
department or ask a qualified expert how
the operation should be performed.
3. SAFE SERVICING. Disconnect power and
allow impeller to come to a complete stop
before servicing or working on the dust col-
lector ducting system.
8. DUST HAZARD. Be aware that certain
woods may cause an allergic reaction
in people and animals, especially when
exposed to fine dust. Make sure you know
what type of wood dust you will be exposed
to in case there is a possibility of an allergic
reaction. Always wear an approved respira-
tor!
4. SUSPENDED DUST PARTICLES AND
IGNITION SOURCES. Do not operate the
dust collector in areas where explosion risks
would be high if dust were dispersed into
the area. Areas of high risk include, but are
not limited to, areas near pilot lights and/or
open flames.
5. EMPTYING BAGS. When emptying dust
from the collection bags, wear a respira-
tor and safety glasses. Empty dust into an
approved container and dispose of prop-
erly.
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. Failure to follow guidelines could
result in serious personal injury, damage to
equipment or poor work results.
DO NOT use the dust collector for any
other purpose besides collecting dust from
connected woodworking machines. A dust
collector should NEVER be used as an air
cleaner. For safest use, wear a respirator
and use an air cleaner in addition to the
dust collector.
G0583 1 HP Canister Dust Collector
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: CIRCUIT REQUIREMENTS
Plug and Recepticle Requirements
110/220V Operation
The motor is prewired to 110V and no plug
replacement is required. For 220V connection,
The Model G0583 features a single phase
110V/220V 1 HP motor, which is prewired to
110V.
rewire the motor as in Figure 2, and install a
NEMA 6-15 plug (Figure 1). You may also “hard-
wire” the dust collector directly to your panel, pro-
vided you place a disconnect near the machine.
Check the electrical codes in your area for specif-
ics on wiring requirements.
Amperage Draw
110V ....................................................... 9 Amps
220V .................................................... 4.5 Amps
Circuit Breaker Requirements
Use the following guidelines when choosing a
circuit breaker (circuit breakers rated any higher
are not adequate to protect the circuit):
Circuit Breaker
110V .......................................................15 Amp
220V .......................................................10 Amp
Always check to see if the wires in your circuit
are capable of handling the amperage draw from
your machine, as well as any other machines that
could be operating on the same circuit. If you are
unsure, consult a qualified electrician.
Figure 1. NEMA 6-15 plug and receptacle.
������
�����������
A fire may occur if your particular electrical
configuration does not comply with local and
state codes. The best way to ensure compli-
ance is to check with your local municipality
or a qualified electrician.
������
���������
�������
��������
������
��������
�����������
������������
������
�����������
���������
�������
������
��������
������
��������
�����������
������������
Figure 2. 110V/220V motor wiring diagram.
-8-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension Cords
Grounding
We do not recommend the use of extension cords
with 220V equipment. Instead, arrange the place-
ment of your equipment and the installed wiring
to eliminate the need for extension cords. Should
the situation be necessary to use an extension,
make sure the cord is rated Standard Service
(grade S) or better. The extension cord must also
contain a ground wire and plug pin. Always repair
or replace extension cords when they become
worn or damaged.
Electrocution or a fire
can result if the machine
is not grounded cor-
rectly. Make sure all
electrical circuits are
grounded. DO NOT use
the machine if it is not
grounded.
NOTICE
The wire on the power cord with green or
green and yellow striped insulation is the
grounding conductor.
In the event of an electrical short, grounding
reduces the risk of electric shock by providing a
path of least resistance to disperse electric cur-
rent. This tool is equipped with a power cord that
has an equipment-grounding prong. The outlet
must be properly installed and grounded in accor-
dance with all local codes and ordinances.
G0583 1 HP Canister Dust Collector
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: SET UP
Items Needed For
Set Up
This machine presents
serious injury hazards
to untrained users. Read
through this entire man-
ual to become familiar
with the controls and
Items Needed for Setup
QTY
Hex Wrench 3mm...............................................1
Wrench or Socket 12mm....................................1
#2 Phillips Screwdriver.......................................1
operations
BEFORE
starting the machine!
Inventory
Wear safety glasses dur-
ing the entire set up pro-
cess!
After all the parts have been removed from the
two boxes, you should have the following items:
Box 1: Canister Components (Figure 3)
QTY
A. Canister Filter ............................................. 1
B. Gasket Bag................................................. 1
— Wide Foam Strip.................................... 1
— Narrow Foam Strip................................. 1
C. Canister Filter Cleaning Handle ................. 1
D. Metal Canister Clamp ................................ 1
The Model G0583 is a
heavy machine (approxi-
mately 60 lbs. shipping
weight). DO NOT over-
exert yourself while
unpacking or moving
your machine—get assis-
tance.
A
Unpacking
Your machine left our warehouse in two care-
fully packed boxes. If you discover the machine
is damaged after you have signed for delivery,
please immediately call Customer Service at
(570) 546-9663 for advice.
B
D
Save the containers and all packing materials
for possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
C
Figure 3. Canister filter box components.
When you are completely satisfied with the con-
dition of the shipment, you should inventory the
equipment.
-10-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Box 2: Main Components (Figure 4)
Site Considerations
E. Elbow 4"...................................................... 1
F. Base............................................................ 1
G. Clear Dust Storage Bag ............................. 1
H. Round Support ........................................... 1
I. Rectangle Supports .................................... 2
J. Swivel Casters ........................................... 2
K. Fixed Casters ............................................ 2
L. Impeller/Separator ...................................... 1
M. Lower Bag Clamp....................................... 1
N. Handle ........................................................ 1
O. Hardware Bag............................................. 1
— Hex Bolt 5/16"-18 x 1/2"........................... 12
— Acorn Nut 5/16"-18....................................4
— Flat Washer 5/16" .....................................2
— Flat Head Screw 5/16"-18 x 1"..................2
— Flange Screw 10-24 x 3/8"...................... 1
— Open-End Wrench 10-12mm................. 1
— Hex Wrench 5mm ................................. 1
— Hex Bolt M6-1.0 x 10............................. 4
Working Clearances
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
the machine. See Figure 5 for the machine foot-
print dimensions of the Model G0583.
30"
16"
L
Figure 5. Dust collector footprint.
F
M
J
K
G
Unsupervisedchildrenand
visitors inside your shop
could receive serious per-
sonal injury. Ensure child
and visitor safety by keep-
ing all entrances to the
shop locked at all times.
DO NOT allow unsuper-
vised children or visitors
in the shop at any time.
O
I
E
H
N
Figure 4. Main box items.
In the event that any non proprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or, for the sake of expedi-
ency, replacements can be obtained at your local
hardware store.
G0583 1 HP Canister Dust Collector
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Recognition Chart
-12-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Base and Supports
4. Place the round and rectangle supports on
the base and install with six 5⁄16"-18 x 5⁄16" hex
bolts (see Figure 7).
Components and Hardware Needed:
QTY
Base ...................................................................1
Casters ...............................................................4
Round Support ...................................................1
Rectangle Support..............................................2
..............................................2
Impeller/Separator
................................................................1
Handle
Hex Bolts 5⁄16"-18 x 1⁄2" ........................................6
Hex Bolts M6-1.0 x 10........................................4
Acorn Nuts 5⁄16"-18 .............................................4
Flat Head Screws M6-1.0 x 10...........................2
Phlips Screw 10-24 x 3⁄8"................................... 1
Flat Washers 5⁄16"-18...........................................2
Tools Needed:
Wrench or Socket 12mm....................................1
Figure 7. Impeller/separator supports.
#2 Phillips Screwdriver.......................................1
5. Align the impeller/separator assembly with
the supports, and install six 5⁄16"-18 x 1⁄2" hex
bolts (see Figure 8).
To assemble the dust collector base:
1. Make sure the dust collector motor is
unplugged!
6. Position the elbow as shown in Figure 8,
3
and secure it in place with the #10-24 x ⁄8
"
phlips head screw.
5
2. Install the the casters with the four ⁄16"-18
acorn nuts and washers. (see Figure 6).
7. Position the handle as shown in Figure 8,
and secure it in place with two M6-1 x 10 flat
head screws.
Figure 6. Installing casters.
Figure 8. Impeller/separator attached to base.
G0583 1 HP Canister Dust Collector
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Filter
3. Install the handle onto the top of the canister
and tighten the set screw against the flat of
the shaft (Figure 10).
Components and Hardware Needed:
QTY
Canister Filter.....................................................1
Handle ................................................................1
Metal Canister Clamp.........................................1
Narrow Foam Strip .............................................1
Tools Needed:
Hex Wrench 3mm...............................................1
To install the canister:
1. Secure the narrow foam strip around the
outside top rim of the collector as shown in
Figure 9.
Shaft Flat
Figure 10. Installing canister handle.
4. Place the canister on top of the collector.
5. Position the metal canister clamp around the
bottom of the canister filter, so it will com-
press around the foam strip (Figure 11), and
latch the clamp closed.
Figure 9. Narrow foam strip.
2. Trim the excess foam strip so the ends come
together evenly as shown in Figure 9.
Figure 11. Installed and secured canister filter.
-14-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Collection Bag
3. Tighten the lower bag clamp around the wide
foam strip to seal and secure the lower col-
lection bag (Figure 13).
Components and Hardware Needed:
QTY
Clear Collection Bag...........................................1
Lower Bag Clamp...............................................1
Wide Foam Strip.................................................1
To install the collection bag:
1. Secure the wide foam strip around the out-
side bottom rim of the collector and trim the
excess (Figure 12).
Wide Foam Strip
Figure 13. Dust collection bag installed.
Figure 12. Installed and trimmed wide foam
strip.
2. Slide the clear collection bag around the
bottom of the collector so the rim of the bag
overlaps onto the foam strip.
G0583 1 HP Canister Dust Collector
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: COLLECTION SYSTEM
Material Selection
General
You have many choices regarding dust collection
ducting, but flexible hose is the most common.
However, be aware that there is a fire or explo-
sion hazard if plastic duct material is used for
dust collection without being grounded against
static electrical charge build-up. This topic will be
discussed later in the manual.
The Model G0583 is designed to be a single-
machine dust collector. Locate the dust collec-
tor where it will not interfere with the workpiece
being processed, and no more than 10' of duct-
ing is used, otherwise the CFM will be reduced.
To solve dust collection questions, Grizzly offers
a guide book entitled Canister Dust Collection
Basics that will help you design your system.
Metal Rigid Duct
Whatever system you choose, always make sure
there are no open flames or pilot lights in the
same room as the dust collector. There is a risk
of explosion if dust is dispersed into the air.
Metal ducting comes in many varieties, make
sure that what you use is suitable for dust
collection. Advantages of metal ducting is its
conductivity and that it does not contribute to
static electrical charge build-up. However, static
charges are still produced when dust particles
strike other dust particles as they move through
the ducting. Since metal ducting is a conductor,
it can be grounded quite easily to dissipate any
static electrical charges. However, metal ducting
is generally more expensive than plastic duct-
ing and it is not usually airtight unless specifi-
cally manufactured for dust collection. Specially
manufactured metal ducting, on the other hand,
is quite expensive. Metal ducting is also gener-
ally more difficult to cut and assemble.
Plastic Flexible Duct
Flexible rubber hose, polyethylene, plastic flex-
hose and other flexible ribbed hose is generally
used for short runs, small shops, and at rigid
duct-to-tool connections. There are many dif-
ferent types of flex hose on the market today.
These are manufactured from materials such as
polyethylene, PVC, cloth hose dipped in rubber
and even metal, including steel and aluminum.
-16-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
There are also many kinds of pure plastic flex-
ible hose, such as non-perforated drainage type
hose and dryer vent hose. Drainage type hose,
while being economical, does not quite have the
flexibility required for dust collection. The inside
of the duct is also deeply corrugated and can
increase the static pressure loss by as much as
50% over smooth wall duct. Dryer vent hose,
while being completely flexible, is non-resistant
to abrasion and has a tendency to collapse in a
negative pressure system.
Duct Grounding
Since plastic hose is abundant, relatively inex-
pensive, easily assembled and air tight, it is a
very popular material for conveying dust from
woodworking machines to the dust collector. We
recommend using flexible hose (flex-hose) to
connect the woodworking machine to the dust
collector. However, plastic flex-hose and plastic
ducting are an insulator, and dust particles mov-
ing against the walls of the plastic duct create a
static electrical build up. This charge will build
until it discharges to a ground. If a grounding
medium is not available to prevent static electrical
build up, the electrical charge will arc to the near-
est grounded source. This electrical discharge
may cause an explosion and subsequent fire
inside the system.
If using flex-hose, you should choose one of the
many types that are designed specifically for
the movement of solid particles, i.e. dust, grains
and plastics. However, the cost of specifically
designed flexible duct can vary greatly. Grizzly
offers polyethylene hose, which is well suited for
the removal of particulate matter, especially saw-
dust, since it is durable and completely flexible.
Polyethylene is also very economical and avail-
able in a wide variety of diameters and lengths for
most applications.
To protect against static electrical build up inside
a non-conducting duct, a bare copper wire should
be placed inside the duct along its length and
grounded to the dust collector. You must also
confirm that the dust collector is continuously
grounded through the electrical circuit to the elec-
tric service panel.
Plastic Rigid Duct
The popularity of plastic duct is due to the fact that
it is an economical and readily available product.
It is also simple to assemble and easily sealed
against air loss. The primary disadvantage of
plastic duct for Canister Dust collection, whether
black ABS or white PVC and even rubber or
polyethylene flex-hose, is the inherent danger of
static electrical build-up.
Always guard against
static electrical build up
by grounding all dust
collection lines.
G0583 1 HP Canister Dust Collector
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Be sure that you extend the bare copper wire
down all branches of the system. Do not forget
to connect the wires to each other with wire nuts
when two branches meet at a “Y” or “T” connec-
tion.
We also recommend wrapping the outside of all
plastic ducts with bare copper wire to ground the
outside of the system against static electrical
build up. Wire connections at Y’s and T’s should
be made with wire nuts.
Ensure that the entire system is grounded. If
using plastic blast gates to direct air flow, the
grounding wire must be jumped (Figure 14)
around the blast gate without interruption to the
grounding system.
Attach the bare ground wire to each stationary
woodworking machine and attach the canister
dust collector frame with a ground screw as
shown in Figure 15. Ensure that each machine is
continuously grounded to the grounding terminal
in your electric service panel.
Plastic Blast Gate
Ground Screw
Flex-Hose
Metal Duct
Copper Ground Wire
External Ground Wire
Internal Ground Wire
Figure 14. Ground jumper wire when using
plastic blast gates or elbows and metal duct.
Figure 15. Flex-hose grounded to machine.
-18-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Keep ducting directional changes to a mini-
mum. The more directional change fittings
you use, the greater the loss of overall pres-
sure.
Ducting Suggestions
This dust collector is intended for single machine
use and not designed to draw dust through long
runs and multiple ports simultaneously. We do
not recommend using ducting any longer than
10 feet. Otherwise, dust collection efficiency will
be greatly reduced. However, still consider these
general guidelines for efficient dust collection:
4. Gradual directional changes are more effi-
cient than sudden directional changes (i.e.
use the largest corner radius possible when
changing hose or pipe direction).
5. The simpler the system, the more efficient
and less costly it will be.
1. Machines that produce the most sawdust
should have the shortest run of ducting
between the dust collector and the machine.
These machines include thickness planers,
shapers, sanders, and bandsaws.
2. Ideally, you should design your shop layout
so machines will have the shortest possible
run to the dust collector.
G0583 1 HP Canister Dust Collector
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: OPERATION
Test Run
Operation Safety
Once assembly is complete and adjustments are
done to your satisfaction, you are ready to test
run the machine.
Disconnect power to the
machine when perform-
ing any maintenance,
assembly or adjust-
ments. Failure to do this
may result in serious
personal injury.
Turn on the power supply at the main panel.
Turn the dust collector ON. Make sure that your
finger is poised on the toggle switch, just in case
there is a problem shut-off will be quick. The dust
collector should run smoothly, with little or no
vibration or rubbing noises. Strange or unnatu-
ral noises should be investigated and corrected
before operating the machine further.
If you cannot easily locate the source of an
unusual noise or vibration, contact our service
department for help.
Keep loose clothing
rolled up and out of the
way of machinery and
keep hair pulled back.
General
Wear safety glasses dur-
ing the entire operations
process. Failure to com-
ply may result in serious
personal injury.
Operating your Model G0583 is simple and
straightforward. Move the dust collector to the
machine location, connect the duct, connect the
ducting ground, and you are ready to begin.
Always wear a respi-
rator when operating
your dust collector. This
machine circulates saw-
dust dust which may
cause allergic reactions
or respiratory problems.
DO NOT use the dust collector for any
other purpose besides collecting dust from
connected woodworking machines. A dust
collector should NEVER be used as an air
cleaner. For safest use, wear a respirator
and use an air cleaner in addition to the
dust collector.
-20-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTENANCE
Lubrication
Disconnect power to the
machine when perform-
ing any maintenance,
assembly or adjust-
ments. Failure to do this
may result in serious
personal injury.
Since all bearings are shielded and permanently
lubricated, simply leave them alone until they
need to be replaced. Do not lubricate them.
Bag and Canister
Keep loose clothing
rolled up and out of the
way of machinery and
keep hair pulled back.
Cleaning
Always wear a respirator or dust mask and safety
glasses when emptying the storage bag (Figure
16). The safest opyion is to seal and discard the
entire bag and its contents. Small dust particles
can escape the bags during emptying, causing
them to become airborne and easily inhaled. This
microscopic airborne dust is extremely unhealthy
to breathe and can cause serious health prob-
lems.
Wear safety glasses dur-
ing the entire mainte-
nance process. Failure
to comply may result in
serious personal injury.
Grizzly offers replacement plastic collection bags
Schedule
(Part Number H2290) and canister filters for your
Model G0583 Canister Dust Collector.
Regular periodic maintenance on your Model
G0583 Canister Dust Collector will ensure its
optimum performance. Make a habit of inspecting
your machine each time you use it. Check for the
following conditions and repair or replace when
necessary:
1. Loose mounting bolts.
2. Worn switch.
3. Worn or damaged cords and plugs.
4. Any other condition that could hamper the
safe operation of this machine.
Figure 16. Safely disposing of wood dust.
5. Do not let collection bags get completely
full.
G0583 1 HP Canister Dust Collector
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
To clean the canister filter:
While the Model G0583 excels at collecting the
majority of wood dust produced by your machines,
it is not an air filter; therefore, we strongly rec-
ommend the supplemental aid of a shop air filter
such as the Grizzly G5955 or G9956. Air filters
are designed to collect the smaller dust particles
that a canister style dust collector cannot trap.
1. Rotate the canister handle 360º in both direc-
tion to vibrate the pleated canister element
and free trapped dust particles from the filter
(Figure 17). The particles will fall into the col-
lection bag.
Figure 17. Rotate canister handle 360º back
and forth.
To empty the collection bag:
1. Make sure you are wearing a respirator and
the canister dust collector is unplugged.
2. When the collection bag is full, un-clamp the
collection bag and empty it, or tie it off and
dispose of it altogether.
3. Reinstall or replace the collection bag.
-22-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Motor will not start, or it
growls on start up.
1. Power supply fuse or circuit
breaker has tripped.
1. Disconnect power, and inspect circuit for electrical
shorts and repair. Replace circuit breaker if it is
old or has tripped many times.
2. Toggle switch is broken inside.
3. Start capacitor is at fault.
2. Disconnect power, and use an ohmmeter to check
switch terminals for continuity, and replace switch
if required.
3. Replace start capacitor.
4. Motor fan cover is dented, stopping 4. Replace motor fan cover (and fan, if damaged).
the fan from being able to spin.
5. Motor is at fault.
5. Replace motor.
Motor runs slower than
normal.
1. Poor electrical connection.
1. Inspect the power supply for loose, corroded, or
overheated electrical connections and repair.
2. Have the power source voltage checked; reduce
the length of extension cord.
2. Low power source voltage.
3. Motor is at fault.
3. Replace the motor.
Loud, repetitious noise, or 1. Dust collector is not on a flat
1. Stabilize the dust collector.
excessive vibration coming
from dust collector.
surface and wobbles.
2. Impeller fan is damaged and
unbalanced.
2. Unplug dust collector, and inspect the impeller for
dents, bends, loose fins. Replace impeller if any
damage is found.
3. The motor mounting is loose.
3. Make sure all fasteners on the dust collector are
tight.
4. Impeller is loose on the motor
shaft.
5. Motor fan cover is dented, causing
the motor fan to hit the cover
while spinning.
4. Replace the motor and impeller as a set if the
motor shaft and the impeller hub is damaged.
5. Replace motor fan cover.
Dust collector does not
1. Dust collection bag is full.
1. Empty bags.
adequately collect dust or 2. There is a restriction at the inlet
2. Remove dust line from dust collector inlet and
clean debris from the inlet grate (and wire-
connector, if installed).
chips; poor performance.
grate.
3. The dust collector is too far away
from the point of suction, or there
are too many sharp bends in the
ducting.
3. Relocate the dust collector closer to the point of
suction, and rework ducting without sharp bends.
Refer to the Dust Collection Basics handbook (ISBN
0-9635821-2-7) to help configure your dust system.
4. The lumber is wet and not flowing 4. Process lumber with less than 20% moisture
through the dust lines smoothly. content.
5. There is a leak in the ducting, or a 5. Rework the ducting as to eliminate all leaks, and
series of small leaks, or too many
open ports.
refer to the Dust Collection Basics handbook (ISBN
0-9635821-2-7) for more solutions.
6. There is a restriction in the
ducting, or the ducting and ports
are incorrectly sized.
6. Rework the ducting as to eliminate all restrictions,
and refer to the Dust Collection Basics handbook
(ISBN 0-9635821-2-7) for more solutions.
7. The machine dust collection design 7. Ask your dealer for proper dust collection
is inadequate.
accessories or the SHOP FOX® Dust Collection
Nozzle on Stand.
8. The dust collector is too small for
the dust collection system.
8. Install a larger dust collector to power your dust
collection system.
G0583 1 HP Canister Dust Collector
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
G0583 Parts Breakdown
���
���
���
���
���
�
�
���
���
���
���
�
�
��
�
�
��
Refer to
�
Page 28 for
Breakdown.
��
��
��
�
��
�
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
-24-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Breakdown
33
36
35
37
50
51
31-1
52
53
39
54
41
43
40
38
42
46
52
45
53
50-1
44
37
47
48
G0583 1 HP Canister Dust Collector
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
24 P0583024
25 PFS03
26 P0583026
27 H2290
28 P0583028
29 P0583029
30 P0583030
31 P0583031
FOAM HAND GRIP
FLANGE SCR 10-24 X 3/8"
4" ELBOW
DUST STORAGE BAG
LOWER BAG CLAMP
HAND RAIL
1
P0583001
PC035
PSW09
PSW09-1
P0583031-4 FAN
P0583031-5 FAN COVER
P0583031-6 SWITCH HOUSING
PFS03
P0583031-8 SWITCH COVER
P0583031-9 POWER CORD
PK01M
1 HP MOTOR
S. CAPACITOR 35MFD/300V
SWITCH
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
SWITCH KEY
PLASTIC CAP 5/8"
IMPELLER HOUSING
FLANGE SCR 10-24 X 3/8"
31-1 P0583031-1 FOAM STRP 5 X 42MM
32 P0583032
33 P0583033
35 PSS01M
36 P0583036
37 PS09M
38 P0583038
39 PB04M
40 P0583040
41 P0583041
42 PS20M
43 PLN02M
44 P0583044
45 P0583045
46 PN06M
47 PW06
48 PS68M
6MM CONCAVE WASHER
HANDLE
SET SCREW M6-1.0 X 10
HANDLE
PHLP HD SCR M5-.8 X 10
FLAP BOARD
HEX BOLT M6-1 X 10
RUBBER FLAP
KEY 5 X 5 X 22MM
SHAFT SEAL
P0583003
PW06
FLAT WASHER 1/4"
WRENCH 10-12MM
5MM HEX WRENCH
CAP SCREW M6-1.0 X 20
INLET COVER
SET SCREW 5/16"-18 X 5/16"
HEX BOLT 1/4”-20 X 1/2”
IMPELLER/HUB ASSEMBLY
PHLP HD SCR M5-0.8 X 10
HEX BOLT 5/16"-18 X 1/2"
RECTANGLE SUPPORT LEG
BASE
PWR1012
PAW05M
PSB02M
P0583008
PSS17
PB19
P0583011
PS09M
FLAP PLATE
PHLP HD SCR M5-.8 X 15
LOCK NUT M5-.8
BOTTOM PLATE
SUPPORT TAB
PB09
HEX NUT M5-.8
P0583014
P0583015
P0583016
P0583017
PW07
PN40
PB04M
P0583021
P0583022
PFH25
FLAT WASHER 1/4
PHLP HD SCR M6-1 X 10
FILTER
SWIVEL CASTER
FIXED CASTER
50 P0583050
50-1 P0583050-1 FOAM GASKET 10 X 15 MM
FLAT WASHER 5/16"
ACORN NUT 5/16"-18
HEX BOLT M6-1.0 X 10
ROUND SUPPORT LEG
FOAM GASKET
51 P0583051
52 P0583052
53 P0583053
54 P0583054
55 P0583055
CANISTER BAND CLAMP
THREAD BEARING
BEARING PLATE
HEX SPINDLE
COMPLETE CANISTER ASSY
FLAT HD SCR 5/16"-18 X 1"
-26-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
H2797—SHOP FOX® Remote Dust Collector
Switch.
G4679—Grounding Kit
Eliminate potential hazards by dissipating static
charges. Kit includes 50' of 14-gauge bare cop-
per wire, electrical connectors, grounding screws,
terminal ends and instructions.
This remote switch turns your dust collector on
and off from anywhere in your shop up to 75 feet
away, saving you trips to your collector when-
ever you operate a shop machine. Includes two
controls with 9V batteries. Use H2797 on 110V
dust collectors up to 11⁄2 HP. Use H5397 on 220V
dust collectors up to 3 HP.
G2525—Dust Collection Basics
This incisive book skillfully guides the wood-
worker through all the steps necessary in
the design and construction of an efficient cen-
tral dust collection system and tells you what
you need to know for easy installation. The
text offers practical hints and techniques and
takes the mystery, misery and hype away from
a subject that should be as clear as the air you
breathe. Fifty pages of concise, carefully illus-
trated text. A MUST!
G3181—Dust Collection Kit #1
Designed for a one machine hook-up, kit #1
comes complete with installation instructions
and an accessories list for expanding your
dust collection system in the future. Acessories
included:
• (1) G1536 4" x 10' Hose
• (1) G1838 Universal Dust Hood
• (2) G2974 Wire Hose Clamps
G0583 1 HP Canister Dust Collector
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
-28-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
G0583 1 HP Canister Dust Collector
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-30-
G0583 1 HP Canister Dust Collector
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email ________________________ Invoice #_________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Old House Journal
____ Shotgun News
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____ 6-9
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
Visit Our Website Today And Discover Why
Grizzly® Is The Industry Leader!
• SECURE ORDERING
• ORDERS SHIPPED WITHIN 24 HOURS
• E-MAIL RESPONSE WITHIN ONE HOUR
-OR-
Call Today For A
FREE
Full Color Catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
|