MODEL
H7792/H7793/H7794/H7795
CORDLESS DRILL
OWNER'S MANUAL
COPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#EW7591 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION...............................................................................................................2
Foreword.....................................................................................................................2
Contact Information ....................................................................................................2
Machine Data Sheet...................................................................................................3
Identification................................................................................................................4
SECTION 1: SAFETY.......................................................................................................5
Safety Instructions for Machinery ...............................................................................5
Additional Safety Instructions for Cordless Drills........................................................7
Additional Safety Instructions for Batteries and Chargers..........................................8
SECTION 2: OPERATIONS.............................................................................................9
Removing/Installing Battery........................................................................................9
Charging Battery.........................................................................................................9
Direction Switch........................................................................................................10
Installing Bits ............................................................................................................10
Torque Settings ........................................................................................................11
Driving Screws..........................................................................................................11
Drilling Tips...............................................................................................................12
Drilling.......................................................................................................................12
SECTION 3: ACCESSORIES.........................................................................................13
SECTION 4: MAINTENANCE ........................................................................................14
Drill Maintenance......................................................................................................14
Charger and Battery .................................................................................................14
Replacement Chargers and Batteries ......................................................................15
WARRANTY AND RETURNS........................................................................................16
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Foreword
Contact Information
We are proud to offer the Grizzly Model
H7792-H7795 Cordless Drills. These mod-
els are part of a growing Grizzly family of
fine power tools. When used according to
the guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
If you have any comments regarding this
manual, please write to us at the following
address:
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
It is our pleasure to provide this manual
with the Model H7792-H7795 Cordless
Drills. It was written to encourage safety
considerations and guide you through
general operating procedures and main-
tenance.
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
The specifications, details, and pho-
tographs in this manual represent the
Model H7792-H7795 as supplied when the
manual was prepared. However, owing
to Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly.
E-Mail: [email protected]
Read the manual before operation.
Become familiar with this tool, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety or
operational information is not under-
stood or followed.
-2-
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Data Sheet
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
Cordless Drill Models
H7792, H7793, H7794, H7795
MODEL
H7792
H7793
H7794
H7795
VOLTAGE
12V
14.4V
12V
18V
AMP HOURS
1.5Ah
1.5Ah
1.5Ah
1.5Ah
0-700
RPM
0-700
RPM
0-600
RPM
0-700
RPM
VARIABLE SPEED
NUMBER OF
CLUTCH SETTINGS
5 + Drill
5 + Drill
22 + Drill
22 + Drill
3
3
3
3
CHUCK CAPACITY
CHARGING TIME
⁄
8
"
⁄
8
"
⁄
8
"
⁄
8
"
1 Hr.
1 Hr.
1 Hr.
1 Hr.
WEIGHT WITH
BATTERY
3.16 lbs.
3.38 lbs.
3.1 lbs.
3.6 lbs.
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
-3-
Identification
D
E
F
C
B
G
H
A
B
I
Figure 1. Drill component identification.
F. Direction Indicator
A. Charger
B. Battery
C. Bit
G. Direction Switch
H. Trigger
D. Keyless Chuck
E. Torque Setting Ring
I. Case
-4-
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazard-
ous conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful infor-
NOTICE
mation about proper operation of the equipment.
Safety Instructions for Machinery
4.
ALWAYS
USE
HEARING
1.
2.
READ THROUGH THE ENTIRE
MANUAL BEFORE STARTING
MACHINERY. Machinery presents
serious injury hazards to untrained
users.
PROTECTIONWHENOPERATING
MACHINERY. Machinery noise can
cause permanent hearing damage.
5.
WEAR PROPER APPAREL. DO
NOT wear loose clothing, gloves,
neckties, rings, or jewelry which
may get caught in moving parts.
Wear protective hair covering to
contain long hair and wear non-slip
footwear.
ALWAYS USE ANSI APPROVED
SAFETY
GLASSES
WHEN
OPERATING
MACHINERY.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
6.
NEVER OPERATE MACHINERY
WHEN TIRED, OR UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL. Be mentally alert at all
times when running machinery.
3.
ALWAYS WEAR AN ANSI
APPROVED RESPIRATOR WHEN
OPERATING MACHINERY THAT
PRODUCES DUST. Wood dust is
a carcinogen and can cause cancer
and severe respiratory illnesses.
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
-5-
7.
ONLY ALLOW TRAINED AND
PROPERLY SUPERVISED PER-
SONNEL TO OPERATE MACHIN-
ERY. Make sure operation instruc-
tions are safe and clearly under-
stood.
17. REMOVE ADJUSTING KEYS
AND WRENCHES. Make a habit
of checking for keys and adjusting
wrenches before turning machinery
ON.
18. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY.
Check for binding and alignment
of parts, broken parts, part mount-
ing, loose bolts, and any other
conditions that may affect machine
operation. Repair or replace dam-
aged parts.
8.
9.
KEEP CHILDREN AND VISITORS
AWAY. Keep all children and visi-
tors a safe distance from the work
area.
MAKE
WORKSHOP
CHILD
PROOF. Use padlocks, master
switches, and remove switch keys.
19. USE
RECOMMENDED
10. NEVER LEAVE WHEN MACHINE
IS RUNNING. Turn power OFF
and allow all moving parts to come
to a complete stop before leaving
machine unattended.
ACCESSORIES. Refer to the
instruction manual for recom-
mended accessories. The use of
improper accessories may cause
risk of injury.
11. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use
machinery in damp, wet locations,
or where any flammable or noxious
fumes may exist.
20. DO NOT FORCE MACHINERY.
Work at the speed for which
the machine or accessory was
designed.
21. SECUREWORKPIECE.Useclamps
or a vise to hold the workpiece when
practical. A secured workpiece pro-
tects your hands and frees both
hands to operate the machine.
12. KEEP WORK AREA CLEAN AND
WELL LIT. Clutter and dark shad-
ows may cause accidents.
13. USE A GROUNDED EXTENSION
CORDRATEDFORTHEMACHINE
AMPERAGE. Undersized cords
overheat and lose power. Replace
extension cords if they become
damaged. DO NOT use extension
cords for 220V machinery.
22. DO NOT OVERREACH. Keep
proper footing and balance at all
times.
23. MANY MACHINES WILL EJECT
THE WORKPIECE TOWARD THE
OPERATOR. Know and avoid con-
ditions that cause the workpiece to
"kickback."
14. ALWAYS DISCONNECT FROM
POWER
SOURCE
BEFORE
SERVICING MACHINERY. Make
sure switch is in OFF position before
reconnecting.
24. ALWAYS LOCK MOBILE BASES
(IF USED) BEFORE OPERATING
MACHINERY.
15. MAINTAIN MACHINERY WITH
CARE. Keep blades sharp and
clean for best and safest perfor-
mance. Follow instructions for lubri-
cating and changing accessories.
25. BE AWARE THAT CERTAIN
WOODS MAY CAUSE AN ALLER-
GIC REACTION in people and ani-
mals, especially when exposed to
fine dust. Make sure you know
what type of wood dust you will be
exposed to and always wear an
approved respirator.
16. MAKE SURE GUARDS ARE IN
PLACE AND WORK CORRECTLY
BEFORE USING MACHINERY.
-6-
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions
for Cordless Drills
1. READ THE ENTIRE MANUAL: This
8. HOLDING THE DRILL: When the
clutch is in the drill position, the
drill can twist severely, causing a
sprained wrist or pinching your hand
between the drill and a solid object.
Hold the drill with both hands and be
aware of the drill position to prevent
injury.
manual contains proper operating
instructions for this drill.
2. REMOVING/INSERTING BATTERY:
Make sure the switch is in the lock
(center) position before inserting or
removing battery.
3. REMOVE BATTERY: Remove the
battery from the drill before changing
bits or making adjustments.
9. JAMMED BIT: Release the trigger,
then slowly reverse the bit out of the
hole. Be prepared for torque twist.
4. INSERTING THE BIT: Insert the bit
all the way into the chuck and tighten
firmly. If the bit is not inserted far
enough the bit may slip.
10. FORWARD/REVERSE: Wait until
the drill has come to a complete stop
before changing direction.
11. ENLARGING HOLES: Enlarging
holes by placing sideways pressure
on the drill bit may cause the bit
to break and/or damage the drill
mechanism.
5. REMOVING THE BIT: The bit may
be hot after use. Use gloves when
removing.
6. WORK AREA: DO NOT drill into
walls that may contain live wires.
Disconnect all power leading the
work area.
12. TRANSPORTING: Prevent acciden-
tal entanglement with clothing and
possible injury by removing the bat-
tery while carrying.
7. HOLDING THE WORKPIECE:
Secure the workpiece with clamps or
a vise to prevent injury. DO NOT hold
the workpiece in your hand or across
your legs.
13. TOOL SERVICE: If drill is damaged
or not working properly, repair it
before continuing to use it.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to your individual working conditions.
Use this and other machinery with caution and respect. Failure to do so could
result in serious personal injury, damage to equipment or poor work results.
Model H7792/H7793/H7794/H7795 Cordless Drills
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions
for Batteries and Chargers
1. READ THE ENTIRE MANUAL: Read
6. CHARGER DAMAGE: Replace
charger if it has been dropped, dam-
aged, or has received a hard impact.
Repair cord immediately if damaged.
and understand all of the instructions
and warnings before charging the
battery.
2. CHARGING EQUIPMENT: Only
charge using the charger and battery
supplied with your drill. DO NOT use
batteries or chargers from other cord-
less tools.
7. SHORTING BATTERY: Avoid touch-
ing both terminals simultaneously
with skin or metal, to prevent injury
from an electrical shock and to pre-
vent a fire from a spark. Storing the
battery in a box of screws or nails
can cause fire from a spark.
3. CHARGING
ENVIRONMENT:
Charge battery on a dry, hard sur-
face in a shaded location with good
ventilation. DO NOT place charger
on or near flammable materials. DO
NOT cover the charger when charg-
ing. Only charge the battery when
the temperature is between 50°F
(10°C)–104°F (40°C). Charging in
temperatures beyond these extremes
will damage the battery.
8. CORD LOCATION: Prevent tripping
over the cord by placing charger
close to a wall and avoiding the use
of an extension cord.
9. CORD CARE: Keep cord away from
heat, oil, and sharp objects. DO
NOT carry the charger by the cord,
or yank the cord to unplug the char-
ger.
4. CHARGER VOLTAGE: DO NOT
plug into a circuit that is not 110-
120V. Changing the charger plug
to plug into 220V will damage the
charger, possibly causing a fire or an
explosion. DO NOT charge from a
DC power supply or a generator.
10. BATTERY DISPOSAL: The battery
must be recycled or disposed of
properly. DO NOT dispose of the
battery in a landfill or incinerate.
Combustion of some of the batteries’
component materials can cause toxic
fumes and possible explosion.
5. DISCONNECT CHARGER: Unplug
the charger when cleaning, or when
not in use.
BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. Consult
your local Yellow Pages directory under the category “Recycling” to locate a
battery recycler in your area.
-8-
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: OPERATIONS
To charge a battery:
Removing/Installing
Battery
1. Plug the charger into a 110V outlet.
2. Insert the battery into the charger. The
battery fits into the oval recess in only
Remove the battery when changing bits,
one way. Do not force the battery.
or to recharge the battery.
Insert until it locks into place.
To remove or install a battery:
Note: Allow the battery to cool down
before charging. After charging is com-
pleted, allow the battery to cool down
before installing it in the drill.
1. Push the direction switch into the lock
(center) position to prevent accidental
starting.
3. The red light will come on (Models
2. Squeeze the lock lever(s) on the bat-
H7792/3 will blink slowly) when the
tery and pull down on the battery to
battery is charging. Charge the bat-
remove.
tery for 1 hour or until the charging
light turns green (Models H7794/5) or
3. Replace the battery by pushing it into
blinks rapidly (Models H7792/3). After
the handle of the drill until the lock
several hours the light will turn off and
lever(s) snap into place.
the unit will stop charging.
Note: The battery can only be installed
in one direction.
Note: It is normal for the battery and
charger to become warm during charg-
ing.
Charging Battery
4. Remove the battery when fully charged
and unplug the charger.
The battery in your new cordless power
tool will not be fully charged when you
receive it. Storage capacity of the battery
will be maximized once it is discharged,
then fully recharged 3-5 times.
Never leave a battery unattended
while charging to prevent a chance
of fire. Disconnect the charger
immediately if the battery or char-
ger becomes too hot to touch,
then have the battery and charger
checked by a qualified electrical
For optimal life span, use the battery until
it can no operate the drill before charg-
ing. Charging the battery before it is fully
drained can reduce battery performance.
service technician.
Follow the instructions below to charge
your battery.
Note: When charging both batteries, wait
15 minutes for the charger to cool between
charging batteries.
Model H7792/H7793/H7794/H7795 Cordless Drills
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Direction Switch
Installing Bits
The direction switch can be placed in the
center position to prevent the drill from
operating, to the right for clockwise bit
rotation, or to the left for counterclockwise
rotation.
This drill is intended for use with drill bits
or screwdriver bits with up to 3⁄8" shanks.
To install a bit:
1. Place the direction switch in the lock
To set the drilling rotation:
(center) position.
1. To place the direction switch (Figure
2) in the lock (center) position, push
the switch until it protrudes equally
from both sides of the drill.
2. Hold the chuck by the collar while turn-
ing the sleeve (Figure 3) to open or
close the chuck jaws.
Chuck
Collar
Chuck
Sleeve
Figure 3. Inserting a bit into the chuck.
Figure 2. Direction switch.
2. Adjust the jaws to the approximate
diameter of the bit or driver and insert
the shank into the chuck.
2. Push the direction switch in from the
right side for clockwise rotation (for-
ward).
3. Turn the sleeve clockwise to tighten the
chuck around the bit or driver. Check
the tightness periodically while using
the tool.
3. Push the direction switch from the
left side for counterclockwise rotation
(reverse).
4. Pull the trigger and look at the lighted
arrows on the top of the drill to confirm
direction.
Note: “Power tightening” (holding the
sleeve while running the drill) can
cause a loose grip on the bit or driver
and potential damage to chuck jaws.
4. To release the bit or driver, hold the
chuck collar, and turn the sleeve coun-
terclockwise.
Note: The bit may be hot after use. Use
gloves when removing.
-10-
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque Settings
Driving Screws
The clutch is designed to slip at a preset
torque to prevent damage to the tool or the
screw, and to prevent driving screws too
deep. Use lower torque settings for screw-
ing into soft materials with short screws,
and higher settings for harder materials
and longer screws. The clutch does not
slip when set in the drill position.
Operating this equipment has the
potential for flying debris to cause eye
injury. Always wear safety glasses or
goggles when operating equipment.
Everyday glasses or reading glass-
es only have impact resistant lenses,
they are not safety glasses. Be certain
the safety glasses you wear meet the
appropriate standards of the American
National Standards Institute (ANSI).
To adjust the torque:
1. Rotate the clutch ring shown in Figure
4 to adjust the torque. The clutch will
slip easiest in the number 1 setting;
the torque increases as the number
increases.
Use the lowest possible torque setting
when driving fasteners to prevent dam-
age to the screw, and to prevent driving
screws too deep.
Clutch
Ring
To drive screws:
1. Install a screwdriver bit that matches
the screw head pattern.
2. Set the torque to an appropriate set-
ting for the workpiece and set the
direction to clockwise (forward).
Figure 4. Torque adjustment clutch ring.
3. Place the screwdriver bit into the
screw and the screw firmly against the
workpiece, start the drill slowly and
gradually increase speed, while apply-
ing pressure to drive the screw into the
workpiece.
2. Turn the clutch ring to the drill setting to
prevent the clutch from slipping.
Note: DO NOT operate the drill with
the clutch set between the highest
number and the drill setting. The clutch
mechanism may be damaged.
Note: You may wish to drill a pilot hole
before driving the screw, depending on
the workpiece and screw type.
To remove screws:
When the clutch is in the drill posi-
tion, the drill can twist severely,
causing a sprained wrist or pinching
your hand between the drill and a
solid object. Hold the drill with both
hands and be aware of the drill posi-
tion to prevent injury.
1. Set the direction to counterclockwise
(reverse) and the clutch to the highest
torque setting.
2. Place the screwdriver bit into the
screw, pull the drill trigger, and push
lightly to keep the bit in the screw.
Model H7792/H7793/H7794/H7795 Cordless Drills
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Drilling Tips
Drilling
Know your worksite: Only drill as deep
as necessary. Check behind walls for
wires, other electrical hazards, or plumb-
ing.
Operating this equipment has the
potential for flying debris to cause eye
injury. Always wear safety glasses or
goggles when operating equipment.
Everyday glasses or reading glasses
only have impact resistant lenses,
they are not safety glasses. Be certain
the safety glasses you wear meet the
appropriate standards of the American
National Standards Institute (ANSI).
Ensure the safety of the workplace:
Clear the work area of all parts and debris
that may cause injury by flying objects.
Securely fix the object to be drilled or fas-
tened in a vise or clamp to avoid injury. Do
not attempt to hold workpiece by hand.
Avoid overloading the drill: Use sharp
drill bits and avoid applying excessive
pressure to the drill. If the speed drops
abnormally, decrease pressure immedi-
ately. If the bit stops abruptly or becomes
blocked, release the trigger at once.
Reverse the direction to free the drill bit.
Performing drilling operations:
1. Install the correct sized drill bit.
2. Set the clutch to drill and set the direc-
Avoid overheating the drill bit: Use
sharp bits that are appropriate for the
workpiece, lubrication, and an oscillating
motion when drilling deep holes to allow
chips to clear and the bit to cool off.
tion to clockwise (forward).
3. Place the drill bit firmly against the
workpiece, start the drill slowly and
gradually increase speed, while apply-
ing pressure to drive the drill into the
workpiece.
Speed and pressure: Use slow speed
when starting to drill and when drilling in
hard material. Only use as much pressure
as needed. Too much pressure and speed
can cause the bit to overheat. Too little
pressure can allow the bit to spin in the
hole, dulling the drill bit.
4. When drilling deep holes, occasionally
pull the drill bit almost all the way out
of the hole to allow chips to clear and
the drill bit to cool.
Drilling metal: Use a center punch to
make a dent at the center of the desired
hole. Drill using a carbide bit, slow speed,
and firm pressure. Use lubrication to pre-
vent overheating the bit.
-12-
Model H
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: ACCESSORIES
G7984—Face Shield
G8865—Cobalt Alloy Drill Bits 13-PC.
G8866—Cobalt Alloy Drill Bits 21-PC
G8867—Cobalt Alloy Drill Bits 29-PC
Cobalt Alloy bits will retain their edge
sharpness longer than normal HSS bits,
resulting in a significant saving of time and
money in the workshop. Includes a heavy-
gauge steel index case for storing. G8865:
1⁄16" -1⁄4"; G8866: 1⁄16"- 3⁄8"; G8867: 1⁄16"-1⁄2".
H1298—Dust Sealed Safety Glasses
H1300—UV Blocking, Clear Safety
Glasses
H2347—Uvex® Spitfire Safety Glasses
H0736—Shop Fox® Safety Glasses
Safety Glasses are essential to every
shop. If you already have a pair, buy
extras for visitors or employees. You can't
be too careful when it comes to shop
safety!
H1300
H1298
G7984
Figure 7. G8865 13-PC Alloy Drill Bits.
H0736
H2347
Figure 5. Our most popular safety
G2575—Pilot Countersink 5-PC. Set
Screw holes may be drilled flush or
counterbored using these quality hex
shanked countersinks.
glasses.
Models G4200–G4207, & H1266–H1271
Hex Power Bits
These hex shaft bits are available in 1"
and 2" lengths , so they work directly in the
chuck or in quick change bit holders.
Figure 8. G2575 Pilot Countersink.
Figure 6. Hex power bits.
Model H7792/H7793/H7794/H7795 Cordless Drills
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: MAINTENANCE
Drill Maintenance
Charger and Battery
The electrical components of this cordless
drill are not user serviceable.
The battery will require periodic recharg-
ing, and eventually replacement after it
has exceeded its recharge life (approxi-
mately 800-1000 recharge cycles). You
will notice extended charging times or
shortened operation time as the battery
experiences more cycles. Refer to the
following page or the Grizzly catalog for
replacement batteries.
Continuous use of a worn or damaged bit
will not only decrease working efficiency,
but also overload the motor, so the bit
must be frequently checked. Replace the
bit if it is worn or damaged.
Plastic parts can easily be cleaned with a
damp cloth, but never use water to clean
any electrical parts. Solvents should also
be avoided on plastic because of the pos-
sibility of damage.
The battery must be recycled or disposed
of properly. DO NOT dispose of the bat-
tery in a landfill or incinerate. Combustion
of some of the battery component materi-
als can cause toxic fumes and possible
explosion.
Keep the drill free from dust, dirt and
grease. Always store it in a dry place, pref-
erably in the case that is supplied.
Keep the charger free from dust, dirt and
grease. Always store it in a dry place,
preferably in the supplied case. DO NOT
store in a location that could exceed 104°F
(40°C), such as a car or metal building.
Disassembly and improper reassem-
bly of this device can result in elec-
trical shock danger. Always have
this device serviced by an qualified
electrical repair technician. Serious
injury will result.
The electrical components of this charger
are not user serviceable. Replace the
charger if it has been dropped, damaged,
or received a hard impact.
BATTERY
MUST
BE
RECYCLED OR DISPOSED
OF PROPERLY. Consult
your local Yellow Pages
directoryunderthecategory“Recycling”
to locate a battery recycler in your
area.
-14-
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Chargers and Batteries
Model H7792:
Model H7794:
Replacement Battery: H8857
Replacement Charger: H8858
Replacement Battery: H8859
Replacement Charger: H8860
Model H7793:
Model H7795:
Replacement Battery: H8861
Replacement Charger: H8862
Replacement Battery: H8863
Replacement Charger: H8864
Model H7792/H7793/H7794/H7795 Cordless Drills
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of
maintenance. This is Grizzly’s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are
hereby limited to the duration of this written warranty. We do not warrant or represent that
the merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to
use this warranty.
Please feel free to write or call us if you have any questions about the machine or the
manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-16-
Model H7792/H7793/H7794/H7795 Cordless Drills
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_________________________________________________________________
Street_________________________________________________________________
City _______________________ State_________________________ Zip _________
Phone #____________________ Email ________________________ Invoice #_____
Model # ____________________ Order #_______________________ Serial #______
The following information is given on a voluntary basis. It will be used for marketing purposes to
help us develop better products and services. All information is strictly confidential.
1. How did you learn about us?
____Advertisement
____Friend
____Catalog
____Card Deck
____Website
Other:________________________
2. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Handy
____ Home Shop Machinist ____ Precision Shooter
____ Journal of Light Cont. ____ Projects in Metal
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking ____ Wooden Boat
____ Practical Homeowner ____ Woodshop News
____ Today’s Homeowner
____ Wood
____ Woodsmith
____ Woodwork
____ Live Steam
____ Model Airplane News ____ Rifle
____ Modeltec
____ Old House Journal
____ RC Modeler
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Shop Notes
____ Shotgun News
3. What is your annual household income?
____$20,000-$29,000
____$30,000-$39,000
____$40,000-$49,000
____$70,000+
____$50,000-$59,000
____$60,000-$69,000
4. What is your age group?
____20-29
____30-39
____60-69
____40-49
____70+
____50-59
5. How long have you been a woodworker/metalworker?
____0-2 Years ____2-8 Years ____8-20 Years
____20+ Years
6. How many of your machines or tools are Grizzly?
____0-2 ____3-5 ____6-9
____10+
____No
____No
7. Do you think your machine represents a good value? ____Yes
8. Would you recommend Grizzly Industrial to a friend? ____Yes
9. Would you allow us to use your name as a reference for our customers in your area?
Note: We never use names more than 3 times. ____Yes ____No
10. Comments:_________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|