Grizzly Drill G0484 User Manual

MODEL G0484

GEARHEAD MILL/DRILL

WITH STAND

OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#CRTS9021 PRINTED IN CHINA

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

INTRODUCTION............................................... 2

SECTION 5: ACCESSORIES......................... 21

Foreword........................................................ 2

Contact Info ................................................... 2

Machine Data Sheet ...................................... 3

Identification................................................... 5

SECTION 6: MAINTENANCE......................... 23

Schedule...................................................... 23

Cleaning and Protecting .............................. 23

Lubrication ................................................... 24

SECTION 1: SAFETY....................................... 6

SECTION 7: SERVICE ................................... 26

Troubleshooting ........................................... 26

Adjusting Gibs.............................................. 27

G0484 Wiring Diagram ................................ 28

220V Single Phase ..................................... 28

Electrical Component Index......................... 29

Table Parts Breakdown ............................... 32

Column Parts Breakdown............................ 34

Head Parts Breakdown, Part A.................... 36

Head Parts Breakdown, Part B.................... 37

Label Placement.......................................... 40

Additional Safety Instructions for Mill/Drills.... 8

SECTION 2: CIRCUIT REQUIREMENTS ........ 9

220V Single-Phase........................................ 9

SECTION 3: SETUP ....................................... 10

Setup Safety ................................................ 10

Items Needed for Setup............................... 10

Unpacking.................................................... 10

Inventory ...................................................... 11

Clean Up...................................................... 11

Site Considerations...................................... 12

Moving & Placing Base Unit ........................ 12

Mounting to Shop Floor ............................... 13

Assembly ..................................................... 13

Test Run ...................................................... 14

Break-In ....................................................... 15

WARRANTY AND RETURNS ........................ 41

SECTION 4: OPERATIONS ........................... 16

Operation Safety.......................................... 16

Control Panel............................................... 16

Spindle Height Control................................. 17

Table Travel................................................. 17

(X-Axis and Y-Axis) .................................... 17

Headstock Travel......................................... 17

(Z-Axis) ....................................................... 17

Tooling Changes.......................................... 18

Choosing Spindle RPM................................ 19

Milling/Drilling............................................... 20

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Foreword

Contact Info

We are proud to offer the Model G0484 Gearhead

Mill/Drill with Stand. This machine is part of a grow-

ing Grizzly family of fine metalworking machinery.

When used according to the guidelines set forth in

this manual, you can expect years of trouble-free,

enjoyable operation and proof of Grizzly’s com-

mitment to customer satisfaction.

If you have any comments regarding this manual,

please write to us at the address below:

Grizzly Industrial, Inc.

Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

The specifications, drawings, and photographs

illustrated in this manual represent the Model

G0484 when the manual was prepared. However,

owing to Grizzly’s policy of continuous improve-

ment, changes may be made at any time with no

obligation on the part of Grizzly.

We stand behind our machines. If you have any

service questions or parts requests, please call or

write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

For your convenience, we always keep current

Grizzly manuals available on our website at www.

grizzly.com. Any updates to your machine will be

reflected in these manuals as soon as they are

complete. Visit our site often to check for the lat-

est updates to this manual!

E-Mail: [email protected]

Web Site: http://www.grizzly.com

-2-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Data Sheet

��

��^��

�

��

��^��

�

��

��^��

�

��

��^��

�

��

��^��

�

��

�� ^��

��^��

�

��

��^��

��

��^��

�

��

-3-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

��

��^��

��

��^��

�

��

��^��

��

��^��

�

��

-4-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Identification

Figure 1. G0484 Identification.

A. Mill/Drill Motor

B. Headstock Lift Motor

C. Fine Feed Knob

D. Headstock Tilt Lock Bolt and Scale

E. Quill Feed Lever

N. Work Lamp

O. Quill Lock Lever

P. Quill Depth Limiter

Q. Quill Depth Scale

R. Master Power Switch

F. Fine Feed Lock Knob

G. Manual Headstock Crank

H. Y-Axis Handwheel

S. Emergency Stop Button

T. Headstock Down Button

U. Headstock Up Button

V. Power Lamp

I. X-Axis Handwheel

J. Power Feed Rapid Feed Switch

K. Power Feed Power Switch

L. Power Feed Speed Dial

M. Power Feed Direction Lever

W. Spindle Direction Switch

X. Reduction Lever

Y. Range Lever

-5-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

��

-6-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

��

�

��

-7-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Safety Instructions for Mill/Drills

1. UNDERSTANDING CONTROLS. Make

sure you understand the use and operation

of all controls before operating machine.

9. POWER DISRUPTION. In the event of a

power outage during use of the mill/drill,

turn OFF all switches to avoid possible sud-

den start up once power is restored.

2. SAFETY ACCESSORIES. Always use a

chip guard in addition to your safety glass-

es when milling to prevent bodily injury.

10. MACHINE CARE AND MAINTENANCE.

Never operate the mill/drill with damaged or

worn parts. Maintain your mill/drill in proper

working condition. Perform routine inspec-

tions and maintenance promptly. Put away

adjustment tools after use.

3. WORK HOLDING. Before starting the

machine, be certain the workpiece has

been properly clamped to the table. NEVER

hold the workpiece by hand when using the

mill/drill.

11. DISCONNECT POWER. Make sure the

mill/drill is OFF, disconnected from the

power source and all moving parts have

come to a complete stop before starting

any inspection, adjustment, or maintenance

procedure.

4. CHUCK KEY SAFETY. Always remove

your chuck key, drawbar wrench, and any

service tools immediately after use.

5. SPINDLE SPEEDS. Select the spindle

speed that is appropriate for the type of

work and material. Allow the mill/drill to

gain full speed before beginning a cut.

12. CLEAN UP. DO NOT clear chips away by

hand—use a brush. Never clear chips while

the mill/drill is turning.

6. STOPPING SPINDLE. DO NOT stop the

spindle by hand. Allow it to come to a stop

by itself.

13. CUTTING TOOL INSPECTION. Inspect

drills and end mills for sharpness, chips,

or cracks before each use. Replace dull,

chipped, or cracked cutting tools immedi-

ately. Handle new cutting tools with care.

Leading edges are very sharp and can

cause lacerations.

7. AVOIDING ENTANGLEMENT. Keep loose

clothing articles such as sleeves, belts or

jewelry away from the mill/drill spindle.

Never wear gloves when operating the mill/

drill.

14. EXPERIENCING DIFFICULTIES. If at

any time you are experiencing difficulties

performing the intended operation, stop

using the machine! Contact our Technical

Support at (570) 546-9663.

8. BE ATTENTIVE. DO NOT leave mill/drill

running unattended for any reason.

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your

individual working conditions. Use this and

other machinery with caution and respect.

Failure to do so could result in serious per-

sonal injury, damage to equipment, or poor

work results.

Like all machinery there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this machine

with respect and caution to lessen the pos-

sibility of operator injury. If normal safety

precautions are overlooked or ignored, seri-

ous personal injury may occur.

-8-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Circuit Requirements

SECTION 2: CIRCUIT REQUIREMENTS

Grounding

220V Single-Phase

In the event of an electrical short, grounding

reduces the risk of electric shock. The grounding

wire in the power cord must be properly connected

to the grounding prong on the plug; likewise, the

outlet must be properly installed and grounded.

All electrical connections must be made in accor-

dance with local codes and ordinances.

Serious personal injury could occur if you

connect the machine to the power source

before you have completed the set up pro-

cess. DO NOT connect the machine to the

power source until instructed to do so.

Electrocution or fire could

Amperage Draw

The Model G0484 motors draws the following

amps under maximum load:

result if this machine is

not grounded correctly

or if your electrical con-

figuration does not com-

ply with local and state

codes. Ensure compliance

by checking with a quali-

fied electrician!

Motor Draw at 220V .............................8¹⁄4 Amps

Circuit Requirements

We recommend connecting your machine to a

dedicated and grounded circuit that is rated for

the amperage given below. Never replace a circuit

breaker on an existing circuit with one of higher

amperage without consulting a qualiﬁed electri-

cian to ensure compliance with wiring codes. If

you are unsure about the wiring codes in your

area or you plan to connect your machine to a

shared circuit, consult a qualified electrician.

Extension Cords

We do not recommend the use of extension cords.

Instead, arrange the placement of your equipment

and the installed wiring to eliminate the need for

extension cords.

If you find it absolutely necessary to use an exten-

sion cord at 220V with your machine:

220V Circuit...........................................15 Amps

•

Use at least a 14 gauge cord that does not

exceed 50 feet in length!

Plug/Receptacle Type

Recommended Plug/Receptacle.... NEMA L6-15

The extension cord must also contain a

ground wire and plug pin.

A qualified electrician MUST size cords over

50 feet long to prevent motor damage.

Figure 2. NEMA L6-15 plug and receptacle.

-9-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 3: SETUP

Setup Safety

Items Needed for

Setup

The following items are needed to complete the

setup process, but are not included with your

machine:

This machine presents

serious injury hazards

to untrained users. Read

through this entire manu-

al to become familiar with

the controls and opera-

tions before starting the

machine!

Description

Qty

•

Assistance...................... 1 or More Persons

Power Lifting Equipment ............ As Needed

Wrench 7mm.............................................. 1

Wrench 12mm............................................ 1

Mounting Hardware.................... As Needed

Cleaning Solvent ........................ As Needed

Shop Rags.................................. As Needed

Wear safety glasses dur-

ing the entire set up pro-

cess!

Unpacking

The Model G0484 was carefully packed when it

left our warehouse. If you discover the machine

is damaged after you have signed for delivery,

please immediately call Customer Service at

(570) 546-9663 for advice.

The Model G0484 is a

heavy machine. Serious

personal injury may occur

if safe moving methods

are not used. To be safe,

get assistance and use

power equipment to move

the shipping crate and

remove the machine from

the crate.

Save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

-10-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Inventory

Clean Up

Inventory

Clean Up

After all the parts have been removed from the

crate, you should have the following items with

your machine:

The unpainted surfaces are coated with a waxy

oil to prevent corrosion during shipment. Remove

this protective coating with a solvent cleaner or

citrus-based degreaser such as Grizzly’s G7895

Citrus Degreaser. To clean thoroughly, some parts

must be removed. For optimum performance

from your machine, clean all moving parts or

sliding contact surfaces. Avoid chlorine-based

solvents, such as acetone or brake parts cleaner

that may damage painted surfaces. Always follow

the manufacturer’s instructions when using any

type of cleaning product.

Inventory: (Figure 3)

Qty

A. Downfeed Handles..................................... 3

B. Face Mill Assembly R8............................... 1

C. Adapter R8 - JT3........................................ 1

D. Headstock Elevation Crank........................ 1

E. Wrench 24mm............................................ 1

F. Hex Wrenches, 4, 5, 6 mm ...................1 Ea

G. Handwheels................................................ 2

H. Chuck 1–16mm JT3................................... 1

I. Chuck Key.................................................. 1

J. Handwheel Handles ................................... 2

Gasoline and petroleum

products have low flash

points and can explode or

cause fire if used to clean

machinery. DO NOT use

these products to clean

the machinery.

Many cleaning solvents are

toxic if inhaled. Minimize

your risk by only using

these products in a well

ventilated area.

Figure 3. Model G0484 inventory.

G7895—Grizzly Citrus Degreaser

This natural, citrus-based degreaser is a great

solution for removing export grease, and it’s much

safer to work around than nasty solvents.

NOTICE

Some hardware/fasteners on the inventory

list may arrive pre-installed. Check mount-

ing locations before assuming that any

items from the inventory list are missing.

If any nonproprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

Figure 4. Grizzly citrus degreaser.

-11-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Site Considerations

Moving & Placing

Site Considerations

Moving & Placing

Base Unit

Floor Load

Refer to the Machine Data Sheet on Page 3 for

the weight and footprint specifications of your

machine. Some residential floors may require

additional reinforcement to support both the

machine and operator.

The Model G0484 is a

heavy machine. Serious

personal injury may occur

if safe moving methods

are not used. To be safe,

get assistance and use

power equipment to move

the shipping crate and

remove the machine from

the crate.

Placement Location

Consider existing and anticipated needs, size of

material to be processed through each machine,

and space for auxiliary stands, work tables, other

machinery, and the operator when establishing a

location for your new machine. See Figure 5 for

the minimum clearance dimensions.

NOTICE

The G0484 is designed to be lifted from the

base. DO NOT lift your mill/drill from the

headstock. Failure to heed this notice will

cause damage to your mill/drill and void the

warranty.

��

To lift the G0484 from the base, remove both side

panels of the base (see Figure 6). Carefully place

the lift forks completely through the base cavity.

��

Be sure to use assistance in this process and only

lift the mill/drill enough to clear floor obstacles as

you move it to its permanent position.

��

Figure 5. Model G0484 clearance dimensions.

Lighting

Lighting should be bright enough to eliminate

shadow in the working zones of the machine and

prevent eye strain. Follow local electrical codes

for proper installation of new lighting.

Children and visitors may be

seriously injured if unsuper-

vised. Lock all entrances to

the shop when you are away.

DO NOT allow unsupervised

children or visitors in your

shop at any time!

Figure 6. Base side panel (right side shown).

-12-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting to Shop Floor

Mounting to Shop

Floor

Assembly

To assemble your mill/drill:

We recommend that you mount your new machine

to the floor. Because floor materials may vary,

floor mounting hardware is not included.

1. Place the handwheels on the longitudinal and

cross lead screws, and tighten the set screw

(see Figure 8).

Lag shield anchors with lag bolts and anchor

studs (Figure 7) are two popular methods for

anchoring an object to a concrete floor.

Set Screw

NOTICE

Anchor studs are stronger and more per-

manent alternatives to lag shield anchors;

however, they will stick out of the floor,

which may cause a tripping hazard if you

decide to move your machine.

Figure 8. Handwheel installed.

2. Thread the handles onto the handwheels and

tighten with a 7mm wrench.

3. Thread the quill feed levers onto the downfeed

hub and tighten with a 12mm wrench (see

Figure 9).

Figure 7. Typical fasteners for mounting to

concrete floors.

Figure 9. Downfeed handles installed.

-13-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Push the emergency stop button in, then

twist it clockwise so it pops out. When the

emergency stop button pops out, the switch

is reset and ready for operation (see Figure

10).

Test Run

Once the assembly is complete, test run your

machine to make sure it runs properly and is

ready for regular operation. The test run consists

of verifying the following: 1) The main motor pow-

ers up and runs correctly and 2) the stop button

safety feature works correctly.

��

If, during the test run, you cannot easily locate

the source of an unusual noise or vibration,

stop using the machine immediately, then review

Troubleshooting on Page 26.

Figure 10. Resetting the switch.

If you cannot find a remedy, contact our Tech

Support at (570) 546-9663 for assistance.

6. Verify that the main motor is operating cor-

rectly by switching the spindle rotation dial to

"F" (forward).

—When operating correctly, the machine

runs smoothly with little or no vibration or

rubbing noises.

Before starting the mill/drill, make sure you

have performed the preceding assembly

and adjustment instructions, and you have

read through the rest of the manual and

are familiar with the various functions and

safety features on this machine. Failure to

follow this warning could result in serious

personal injury or even death!

—Investigate and correct strange or unusual

noises or vibrations before operating the

machine further. Always disconnect the

machine from power when investigating or

correcting potential problems.

7. Press the emergency stop button to stop the

machine and switch the spindle rotation dial

to "0" (neutral).

To test run the machine:

1. Make sure you understand the safety instruc-

tions at the beginning of the manual and that

the machine is setup properly.

8. WITHOUT resetting the emergency stop but-

ton, switch the spindle rotation dial to "F". The

machine should not start.

2. Make sure all tools and objects used during

setup are cleared away from the machine.

—If the machine does not start, the OFF but-

ton safety feature is working correctly. The

Test Run is complete.

3. Connect the machine to the power source.

4. Press the main power switch ON.

—If the machine does start (with the stop

button pushed in), immediately disconnect

power to the machine. The OFF button

safety feature is not working correctly. This

safety feature must work properly before

proceeding with regular operations. Call

Tech Support for help.

-14-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Twist the emergency stop button clockwise

Break-In

so that it pops out.

4. Switch the spindle rotation dial to "F" (for-

After successfully completing the Test Run, it is

necessary run the mill/drill in each speed and

direction without a load to seat the bearings.

ward) and let the spindle run for 10 minutes.

5. Press the emergency stop button in and wait

for the spindle to stop.

NOTICE

6. Switch the spindle rotation dial to "R" (reverse)

Only change spindle speed when the spindle

is stopped. Attempting to change spindle

speeds when the spindle is in motion will

damage the drive gears and bearings.

and let the spindle run for 10 minutes.

7. Repeat Steps 2–6 for the remaining RPM

ranges.

To perform the break-in procedure:

1. Press the emergency stop button in and

make sure the spindle is stopped.

2. Use the gearbox levers so that the spindle

RPM is set at 120.

-15-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 4: OPERATIONS

Operation Safety

Control Panel

A. Power Lamp: Glows when the master power

switch is ON.

Damage to your eyes and lungs could result

from using this machine without proper pro-

tective gear. Always wear safety glasses and

a respirator when operating this machine.

B. Headstock Up Button: Controls the head-

stock motor so the headstock is powerfed

upwards.

C. Headstock Down Button: Controls the

headstock motor so the headstock is power-

fed downwards.

D. Emergency Stop Button: Stops the mill/

drill. Rotate the button clockwise until it pops

back out to reset it.

E. Master Power Switch: Toggles main power

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving

machinery.

to the machine.

F. Spindle Rotation Dial: Changes spindle

rotation direction for milling/drilling operations.

Spindle rotation must always be stopped

before making direction changes.

NOTICE

If you have never used this type of machine

or equipment before, WE STRONGLY REC-

OMMEND that you read books, trade maga-

zines, or get formal training before begin-

ning any projects. Regardless of the con-

tent in this section, Grizzly Industrial will

not be held liable for accidents caused by

lack of training.

Figure 11. Control panel.

-16-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Spindle Height

Control

Table Travel

(X-Axis and Y-Axis)

Spindle height is changed by unlocking the quill

lock lever and the fine feed knob, and using the

quill feed handles or the fine feed knob (Figure

12). The spindle scale indicates the spindle height

in inches and millimeters.

Longitudinal Feed

The longitudinal feed, or X-axis, is moved by

the handwheel at the right end of the table. The

handwheel will move the table in both direc-

tions side-to-side. One complete revolution of the

handwheel moves the longitudinal feed 0.100".

There is also a scale on the front of the table for

use when a tight tolerance is not required.

To change the spindle position:

1. Unlock the quill lock lever and loosen the fine

feed lock knob.

Cross Feed

The cross feed, or Y-axis, is moved with the

handwheel on the front of the table base. One

complete revolution of the handwheel moves the

cross slide 0.100".

2. Pull down on the quill feed levers to lower

or raise the spindle. Lock the quill lock to

hold the spindle in a particular position if you

choose.

3. Tighten the fine feed lock knob and use the

Headstock Travel

(Z-Axis)

fine feed knob if you like.

Tip: Milling with the quill fully extended,

can cause tool chatter. For maximum spindle

rigidity when milling, keep the spindle retract-

ed into the headstock as far as possible,

lock the headstock and quill lock levers, and

tighten the fine feed lock knob.

The vertical headstock travel, or Z-axis travel, is

controlled by the lift motor or the manual head-

stock crank on the right side of the column. This

coarse travel is only used to position the head-

stock in the spindle-travel range. Precise incre-

mental movement is available by using the feed

levers or the fine feed handwheel.

Spindle Scale Quill Feed Lever

Fine Feed Knob

Quill Lock Lever Fine Feed Lock Knob

Figure 12. Spindle controls.

-17-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Tooling Changes

Drawbar

Nut

Your mill/drill has an R-8 spindle taper. Follow

these general procedures to install and remove

R-8 tooling like drill chuck arbors, face cutters, or

collets of your choice.

LACERATION

HAZARD!

Leading edges of end mills

and other cutting tools can

be very sharp. Protect your

hands with gloves or a shop

towel when handling.

Figure 14. Unseating the arbor/cutter.

6. Clear away all items from the cutter before

turning the mill/drill ON.

To install tooling in the spindle:

To remove tooling from the spindle:

1. DISCONNECT MACHINE FROM POWER!

2. Carefully clean the R-8 tapered surface of the

tooling and the spindle. Ensure that they are

free of debris and burrs.

2. Return the headstock to the highest position

and loosen the drawbar.

3. Put on leather gloves, support the tool, and

unthread the drawbar approximately three

turns.

3. Insert the tooling into the spindle, and rotate

it so the slot in the tool taper lines up with the

pin inside of the spindle.

4. Press the tooling up firmly to seat it with the

NOTICE

spindle taper.

DO NOT completely unscrew the drawbar

prior to striking the drawbar or the initial

threads of the drawbar and tool will be

crushed.

5. Finger tighten the drawbar into place, then

tighten the drawbar (Figure 13).

Note: Overtightening the drawbar makes tool

removal difficult and stretches the threads of

the tool and drawbar.

4. Lightly strike the drawbar with a dead blow

hammer (Figure 14) or a piece of wood to

release the tooling from the spindle.

5. Hold the tooling, and unscrew the drawbar.

Figure 13. Tightening drawbar.

-18-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Measure the diameter of your cutting tool in

Choosing Spindle

RPM

inches.

3. Use the following formula to determine the

needed RPM for your operation:

NOTICE

Never shift gears while mill/drill or mill is

running; otherwise, the gear teeth will be

chipped or broken.

Note: You will only be able to get an approxi-

mate RPM value with the gearbox range and

reduction levers.

To determine and set the mill to the needed

cutting RPM:

4. Move the mill gearbox levers to the nearest

milling speed RPM.

1. Select the cutting speed required for the

material of your workpiece using the table in

Figure 15.

NOTICE

Failure to follow RPM and Feed Rate

Guidelines will shorten cutter life and give

poor workpiece results and may threaten

operator safety from ejected parts or broken

tools.

Cutting Speeds for High Speed Steel

(HSS) cutting tools:

Workpiece Material Cutting Speed (sfm)

Aluminum & alloys

Brass & Bronze

Copper

300

150

100

Cast Iron, soft

Cast Iron, hard

Mild Steel

Cast Steel

Alloy Steel, hard

Tool Steel

Stainless Steel

Titanium

Plastics

300-800

300-500

Wood

Figure 15. High speed steel cutting chart.

Note: Double the cutting speed for carbide

cutting tools. These values are a guideline

only.RefertotheMACHINERY'SHANDBOOK

for more detailed information.

-19-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Milling/Drilling

Failure to follow RPM and Feed Rate

Guidelines may threaten operator safety

from ejected parts or broken tools.

To mill a workpiece:

1. Learn about the control panel shown on Page

16 and the controls shown in Figure 16.

Spindle Scale Quill Feed Lever

2. Clamp the workpiece to the milling table, and

adjust the headstock to the needed height,

depth of cut, and milling path.

Note: For special milling operations, loosen

the headstock tilt lock nuts and rotate the

headstock to the needed angle (Figure 17).

Note: If you are only milling in one direction,

lock the unused table slide in place.

Fine Feed Knob

Quill Lock Lever Fine Feed Lock Knob

Figure 16. Milling/drilling controls.

3. Refer to Choosing Spindle RPM on Page

19 to find the best spindle RPM, and then

move the headstock levers to the appropriate

spindle speed positions.

4. Unlock the headstock levers (Figure 18), and

use the lift motor to position the headstock

close to the workpiece.

Note: For maximum spindle rigidity while

milling, keep the spindle retracted into the

headstock as far as possible with the quill

headstock lock levers locked and the fine

feed lock knob tightened.

—For milling tighten the fine feed lock knob

and use the fine feed handwheel and its

scale to set the milling depth. Then lock the

quill lock lever.

Figure 17. Headstock tilt lock.

—For drilling, leave the fine feed lock knob

loose, and use the quill feed lever handles

to draw the quill and drill bit down.

5. Push the green power button.

6. Turn the rotary switch dial to F or R to select

the appropriate cutting direction for the type

of cutter that you are using.

7. Use the table handwheels or the power feed

to move the table so the cutter enters the

workpiece slowly. Refer to the power feed

manual for power feed operation if required.

Figure 18. Headstock lock levers.

-20-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

SECTION 5: ACCESSORIES

H2689—R-8 Quick Change Collet Set

G9324—Boring Head Combo Set

An affordable quick change collet system with

ultra precision. These spring collets are hard-

ened and ground to exacting tolerances and offer

incredible holding power. This set includes an R-8

arbor and nut, spanner wrench, plastic carrying

case and collets sized ¹⁄8", ¹⁄4", ³⁄8", ¹⁄2", ⁵⁄8", ³⁄4", ⁷⁄8",

and 1". What's more, the nut features a self-eject-

ing rim! A set like this will truly speed up any tool

changing process. Drawbar size is ⁷⁄16" x 20.

Hardened and ground adjusting screws along

with a wide base design guarantee a long life and

trouble-free use. Includes a 3" boring head, R-8

shank with 1 /2"-18 TPI, and a 12 piece ³/4" boring

bar set.

Figure 21. G9324 Boring Head Combo Set.

G2861—Face Mill

G4051—Carbide Insert for Face Mill

This 2¹/2" face mill accepts four carbide inserts

(not included). Comes with an R-8 arbor.

Figure 19. H2689 R-8 Quick Change Collet Set.

G1075—52-PC. Clamping Kit, ¹⁄2" T-Nut Size

All the blocks, bolts, nuts, and hold-downs are

case hardened. Each kit includes: Metal rack, 24

studs, 6 step block pairs, 6 T-nuts, 6 flange nuts,

4 coupling nuts, and 6 end hold-downs.

Figure 22. G2861 Face Mill.

Figure 20. G1075 52-PC. Clamping Kit.

-21-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

G9760—20-PC. 2 & 4 Flute TiN End Mill Set.

G5641—1-2-3 Blocks

G9815—Parallel Set

H5556—Edge Finder Set

Includes these sizes and styles in two and four

flute styles: /16", /4", /16", /8", /16", /2", /16", /8",

8", ¹¹/16", and ³/4".

G5641

G9815

Figure 23. G9760 20-PC End Mill Set.

Figure 26. G5641 1-2-3 Blocks, G9815 Parallel

G9765—9-PC. Ball End Mill Set

Set, and H5556 Edge Finder Set.

Features 2 flute ball nose end mills. Includes the

following sizes: ¹/8", ³/16", ¹/4", ⁵/16", ³/8", ⁷/16", ¹/2", ⁵/8

and ³/4".

G7984—Face Shield

H1298—Dust Sealed Safety Glasses

H1300—UV Blocking, Clear Safety Glasses

H2347—Uvex^®Spitfire Safety Glasses

H0736—Shop Fox^®Safety Glasses

Safety glasses are essential to every shop. If

you already have a pair, buy extras for visitors

or employees. You can't be too careful when it

comes to shop safety!

Figure 24. G9765 9 PC. Ball End Mill Set.

H1300

H1298

H3022—Measurement Tool Set

Includes magnetic base, 1" dial indicator (.001"),

and 6" dial caliper (.001"). The extremely low price

has made this a very popular seller!

G7984

H0736

H2347

Figure 27. Our most popular safety glasses.

Figure 25. H3022 Measurement Tool Set.

-22-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 6: MAINTENANCE

Cleaning and

Always disconnect power

to the machine before

performing maintenance.

Protecting

Failure to do this may

result in serious person-

al injury.

Metal chips left on the machine that have been

soaked with water-based coolant will invite oxida-

tion and a gummy residue build-up around the

moving parts. Use a brush and shop vacuum to

remove chips and debris from the working sur-

faces of the mill. Never blow the mill off with com-

pressed air, as this will force metal chips deep into

the mechanisms.

Schedule

For optimum performance from your machine,

follow this maintenance schedule and refer to any

specific instructions given in this section.

Remove any rust build-up from unpainted cast

iron surfaces of your mill and treat with a non-

staining lubricant after cleaning.

Daily Check:

Keep unpainted cast iron surfaces rust-free with

regular applications of products like G96^®Gun

Treatment, SLIPIT^®, or Boeshield^®T-9.

•

Mill/drill is disconnected from power when not

in use.

•

Loose mounting bolts.

Mill/drill is clean.

Lubricate ball oilers.

Ways are cleaned and lubricated.

Cross and longitudinal lead screws are

cleaned and lubricated.

•

Any other condition that would hamper the

safe operation of this machine.

Weekly Maintenance:

Gibs are adjusted properly and lubricated.

•

-23-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Lubrication

Ball Oilers

Lubricate both ball oilers every 8 hours (see

Figures 28–29). Use a manual oiler (oil can) filled

with ISO 68 or SAE 20W non-detergent oil.

To lubricate ball oilers, depress the ball with the

tip of the oil can nozzle and squirt a little oil inside

the fitting. Make sure to clean the outside of the

ball oiler before and after each use to keep out

contaminants.

Figure 29. Cross slide ball oiler.

Ways

Clean the longitudinal, cross, and headstock ways

of all debris. Lightly lubricate each way with ISO

68 or SAE 20W oil.

Longitudinal and Cross Lead

Screws

After cleaning the longitudinal and cross lead

screws of all debris, paint a small amount of white

lithium grease on each one. Then, move the

attached part all the way through its full range of

motion on the lead screw.

Figure 28. Longitudinal ball oiler.

-24-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Headstock Lead Screw

Headstock Gearbox Oil

On an annual basis, or every six months under

heavy use, we recommend that you clean and

lubricate the headstock lead screw with white

lithium grease.

On an annual basis, or every six months under

heavy use, we recommend that you drain and

refill the headstock oil with a 10-30W non-deter-

gent oil.

To clean and lubricate the lead screw:

To change the headstock oil:

1. DISCONNECT MACHINE FROM POWER!

2. Raise the headstock to its highest position.

1. DISCONNECT MACHINE FROM POWER!

2. Locate the drain plug (Figure 31).

3. Hold the rubber chip curtain (Figure 30)

3. Using a 5mm hex wrench, remove the drain

plug located under the headstock, drain the

oil, then reinstall the plug.

away from the lead screw access port.

4. Using mineral spirits, a toothbrush, and rags,

thoroughly clean the lead screw.

4. Remove the fill plug on top of the headstock

and fill the headstock with oil until the sight

glass shows ³⁄4 full, then reinstall the plug.

5. Paint the lead screw and gear teeth with

lithium grease.

6. Lower the headstock and repeat Step 4 on

the upper portion of the lead screw that was

previously inaccessible.

Sight Glass

Drain Plug

Rubber Chip Curtain

Figure 31. Headstock oil access and lubrication.

Lead screw

Figure 30. Headstock lead screw access and

lubrication.

-25-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

SECTION 7: SERVICE

Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-

ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical

Support at (570) 546-9663.

Troubleshooting

Motor & Electrical

Symptom

Possible Cause

Possible Solution

Motor will not

start.

1. Incorrect mill/drill operation.

1. Use the spindle direction ON/OFF lever.

2. Turn the main power panel switch ON.

3. Rotate emergency switch so it pops out.

4. Seek an electrician to troubleshoot and repair the

shop power supply.

2. Main power panel switch is OFF.

3. Emergency switch is pushed in.

4. Circuit breaker or fuse has tripped.

5. No voltage or open connection.

6. Capacitor is at fault.

5. Test circuit, replace wires and connections as

required.

6. Replace capacitor.

7. Power switch or magnetic contactor is at 7. Replace power switch or magnetic contactor.

fault.

8. Transformer or fuse at fault.

9. Motor is at fault.

8. Replace transformer or fuse.

9. Replace motor.

Fuses or circuit

breakers trip

open.

1. Short circuit in line cord or plug.

1. Inspect cord or plug for damaged insulation and

shorted wires.

2. Inspect all connections on motor for loose or shorted

terminals or worn insulation.

2. Short circuit in motor or loose connections.

3. Incorrect fuses or circuit breakers in power 3. Install correct fuses or circuit breakers.

supply.

Table is hard to

move.

1. Chips have loaded up on bedways.

1. Frequently clean away chips that load up during

milling/drilling operations.

2. Ways, gibs, lead screw are at fault .

3. Gibs are too tight.

2. Lubricate ways and lead screw, adjust gibs.

3. Loosen gib screw(s) slightly (Page 27).

Machine is loud

when cutting.

Overheats or

1. Excessive depth of cut.

2. RPM or feed rate wrong for operation.

1. Decrease depth of cut.

2. Refer to RPM feed rate chart (Page 19) for

appropriate rates.

bogs down in the 3. Dull cutters.

cut.

3. Sharpen or replace cutters.

Bad surface fin-

ish when milling.

1. Wrong RPM or feed rate.

1. Adjust for appropriate RPM (Page 19) and feed

rate.

2. Dull tooling or tool not centered correctly.

3. Headstock is loose.

2. Sharpen tooling and/or center tool correctly.

3. Tighten column way gib, lock down headstock lock

levers, and run milling operation with quill fully

retracted into headstock and locked in position.

4. Lubricate ways and tighten gibs.

4. Too much play in gibs.

5. Vise or clamping hardware at fault.

5. Vise or clamping fixture is worn, loose, or inadequate

for clamping task.

6. Incorrect spindle speed or feed rate.

1. Gears not aligned in headstock.

6. Incorrect spindle speed or feed rate.

Gear change

1. Rotate spindle by hand until gear falls into place.

levers will not

shift into position.

-26-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Longitudinal Gib

Adjusting Screw

Adjusting Gibs

The gibs control the accuracy of the table and

headstock movement. During the life of your mill/

drill, you may have to adjust the gibs to remove

looseness that is a result of normal wear.

The goal of gib adjustment is to remove unneces-

sary looseness without causing the dovetail slides

to bind. Loose gibs may cause poor finishes on

the workpiece and may cause undue wear on

the slides; over-tightening may cause pre-mature

wear.

Cross Gib

Adjusting Screw

Figure 32. Cross and longitudinal gib adjusting

screws (one side shown for each).

Each sliding dovetail on the Model G0484 has

a gib that is sandwiched between two adjusting

screws (see Figures 32–33 for the locations of

the gib adjustment screws).

Some minor components must be removed to

access all the gib adjustment screws.

Adjust the gibs by loosening one screw and tight-

ening the other at the opposite end until a slight

drag is felt while moving the table/headstock along

the dovetail slides. Then, tighten the loose screw

at the other end to lock the setting in place.

Figure 33. Headstock gib adjusting screws (left

side of headstock shown).

-27-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

G0484 Wiring Diagram

220V Single Phase

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

-28-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical Component Index

Page 31,

Figure 39.

ELECTROCUTION

HAZARD!

Page 30,

Figure 34.

Page 30,

Figure 36.

Always disconnect power to the

machine before beginning any

electrical procedures. Ignoring

this warning may result in fire

or electrocution!

Figure 1. Mill/drill front left view.

Page 30,

Figure 38.

Page 30,

Figure 37.

Page 31,

Figure 39.

Page 31,

Figure 35.

Figure 2. Mill/drill right rear view.

-29-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 36. Master power switch.

Figure 34. Spindle motor rotary switch,

left and right view.

Figure 37. Spindle motor capacitors and

wiring connections.

Figure 35. Lift motor capacitor and wiring box.

Figure 38. Lift motor junction box.

-30-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 39. Main wiring box.

-31-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Table Parts Breakdown

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

-32-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Table Parts List

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

P0484001

P0484002

PSS03M

HANDLE

PB157M

HEX BOLT M12-1.75 X 130

GIB

HANDWHEEL

P0484024

P0484025

P0484026

P0484027

P0484028

P0484029

PSB31M

SET SCREW M6-1 X 8

GIB ADJUSTING SCREW

SADDLE

P0484004

P0484005

P0484006

P0484007

P0484008

P0484009

PSB14M

HANDWHEEL CLUTCH

GRADUATED DIAL

KNOB M5-.8 X 12

SHIFTING RING

THRUST BEARING 17 X 30 X 9MM

CAP SCREW M8-1.25 X 20

LEAD SCREW SUPPORT

GIB

LOCK HANDLE

STEEL BALL 6.5MM

CAP SCREW M8-1.25 X 25

LEAD SCREW SUPPORT

LEAD SCREW NUT

P0484031

P0484032

P0484033

PSB31M

P0484011

P0484012

P0484013

P0484014

PSB33M

CAP SCREW M8-1.25 X 25

LEAD SCREW

BALL OILER

P0484035

P0484036

P0484037

P0484038

PSB26M

LEAD SCREW

LEAD SCREW SUPPORT

DIAL CLUTCH

CAP SCREW M5-.8 X 12

LEAD SCREW NUT

BASE

P0484016

P0484017

P0484018

PS17M

TABLE

CAP SCREW M6-1 X 12

STOP BLOCK

STAND

P0484040

P0484041

P0484042

P0484043

PB06M

PHLP HD SCR M4-.7 X 6

FRONT PANEL

STOP BLOCK NUT

BALL OILER

P0484020

P0484021

PW06M

SIDE PANEL

REAR TABLE PLATE

HEX BOLT M8-1.25 X 12

FLAT WASHER 12MM

-33-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Column Parts Breakdown

��

-34-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Column Parts List

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

PB06M

HEX BOLT M8-1.25 X 12

SADDLE WAY PROTECTOR

COLUMN

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

P0484123

P0484124

P0484125

P0484126

P0484127

P0484128

P0484029

PN13M

SPRING BASE

P0484102

P0484103

P0484104

P0484105

P0484106

PSB26M

P0484108

PLW10M

PB80M

LEAD SCREW NUT

HEADSTOCK MOUNT

GIB

GEAR SHAFT

THRUST BEARING 15 X 28 X 9MM

GEAR SHAFT BRACKET

CAP SCREW M6-1 X 12

BALL OILER

GIB ADJUSTING SCREW

LOCK HANDLE

STEEL BALL 6.5MM

HEX NUT M16-2

LOCK WASHER 16MM

HEX BOLT M16-2 X 55

SCALE

PSB12M

P0484132

PS07M

CAP SCREW M8-1.25 X 40

COLUMN WAY PROTECTOR

PHLP HD SCR M4-.7 X 8

REFERENCE MARKER

RIVET

P0484111

PS37M

PHLP HD SCR M6-1 X 6

MOTOR MOUNT

P0484134

P0484135

PK147M

P0484137

PK147M

PR09M

P0484113

PSB01M

P0484115

CAP SCREW M6-1 X 16

MOTOR 1/8HP 220V/60HZ/1-PH

KEY 6 X 6 X 18

LEAD SCREW

115-1 P0484115-1 CAPACITOR CBB61 5MFD/450VAC

115-2 P0484115-2 TERMINAL BLOCK

KEY 6 X 6 X 18

EXT RETAINING RING 20MM

BALL BEARING 6204

BEARING BRACKET

BEVEL GEAR

115-3 P0484115-3 MOTOR ELECTRICAL BOX

115-4 P0484115-4 MOTOR JUNCTION BOX

P0484140

P0484141

P0484142

P0484143

PSB26M

P0484145

PN13M

116

117

118

119

120

121

122

PSB06M

PK01M

CAP SCREW M6-1 X 25

KEY 5 X 5 X 22

THRUST BEARING 17 X 30 X 9MM

CAP SCREW M6-1 X 12

SPECIAL LOCK WASHER 16MM

HEX NUT M16-2

P0484118

P0484119

PSS03M

P0484121

P0484122

THRUST BEARING 15 X 28 X 9MM

TOP CLUTCH

SET SCREW M6-1 X 8

BOTTOM CLUTCH

P0484147

PS22M

LAMP

COMPRESSION SPRING

PHLP HD SCR M5-.8 X 25

-35-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

HEAD A

Head Parts Breakdown, Part A

��

�

��

Page 37

��

-36-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

HEAD B

Head Parts Breakdown, Part B

-37-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Head Parts List

REF PART #

201 P0484201

DESCRIPTION

REF PART #

DESCRIPTION

MOTOR 1-1/2HP 220V/60HZ/1-PH

244

245

246

P0484244

PSB05M

201-1 P0484201-1 MOTOR JUNCTION BOX COVER

201-2 P0484201-2 MOTOR JUNCTION BOX

201-3 P0484201-3 CAPACITOR CD60 150MFD/250VAC

201-4 P0484201-4 CAPACITOR CBB60 20MFD/450VAC

201-5 P0484201-5 TERMINAL BLOCK

CAP SCREW M8-1.25 X 50

ELECTRIC BOX

P0484246

246-1 P0484246-1 LIFT MOTOR CONTACTOR KM2

246-2 P0484246-2 LIFT MOTOR CONTACTOR KM1

246-3 P0484246-3 LIFT MOTOR UP BUTTON

246-4 P0484246-4 LIFT MOTOR DOWN BUTTON

246-5 P0484246-5 EMERGENCY STOP BUTTON

246-6 P0484246-6 MASTER JUNCTION TERMINAL BLOCK

246-7 P0484246-7 TRANSFORMER

201-6 P0484201-6 MOTOR FAN COVER

201-7 P0484201-7 MOTOR FAN

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

PSB64M

PK74M

CAP SCREW M10-1.5 X 25

KEY 6 X 6 X 35

HEAD BODY COVER

OIL CAP

P0484204

P0484205

P0484206

PR38M

246-8 P0484246-8 SPINDLE MOTOR ROTARY SWITCH

246-9 P0484246-9 MASTER POWER SWITCH

OIL SEAL

247

248

249

250

251

252

253

254

255

256

257

258

259

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

275

276

277

278

279

280

281

282

283

284

P0484247

P0484248

PLW03M

PW01M

PRESSURE RELIEF HOSE

KNURLED KNOB

LOCK WASHER 6MM

FLAT WASHER 8MM

SPRING CAP

INT RETAINING RING 62MM

BALL BEARING 6007ZZ

MOTOR SHAFT

KEY 6 X 6 X 30

GEAR

P6007

P0484209

PK42M

P0484251

P0484252

PFH05M

P0484254

P0484255

PSS73M

PN02M

P0484211

P6003

COIL SPRING

BALL BEARING 6003ZZ

BEARING BRACKET

STOPPLE

FLAT HD SCR M5-.8 X 12

SPRING BASE

P0484213

P0484214

P0484215

P0484216

P0484217

P0484218

P0484219

P0484220

P0484221

PR07M

GEAR

SET SCREW M10-1.5 X 30

HEX NUT M10-1.5

HANDLE ROD

BUSHING

GEAR

KEY 6 X 6 X14

KEY 5 X 5 X 60

SHAFT

P0484258

P0484259

P0484260

PSS20M

P0484262

P0484263

PR03M

FACE PLATE

STEEL BALL 8MM

COMPRESSION SPRING

EXT RETAINING RING 18MM

BALL BEARING 6202ZZ

INT RETAINING RING 35MM

O-SEAL RING

CAP

SET SCREW M8-1.25 X 8

SPEED LEVER

OIL SEAL

P6202

EXT RETAINING RING 12MM

LEVER SHAFT ( LEFT )

HEX NUT M6-1

SET SCREW M6-1 X 12

LEVER ( LEFT )

PR21M

P0484265

PN01M

P0484225

P0484226

P0484227

P0484228

PK36M

PSS04M

P0484268

P0484269

P0484270

P0484271

P0484272

P0484273

PS17M

GEAR

SHAFT

KEY 5 X 5 X 50

KEY 6 X 6 X 75

GEAR

LEVER BRACKET

P0484230

P0484231

P0484232

P0484233

P0484234

P0484235

PS05M

LEVER ( RIGHT )

LEVER SHAFT ( RIGHT )

PHLP HD SCR M4-.7 X 6

SPECIAL NUT

GEAR

AIRTIGHT RING

AIRTIGHT BASE

PHLP HD SCR M5-.8 X 8

OIL SEAL

P0484275

P0484276

P0484277

P0484278

P0484279

P0484280

PS05M

HEAD BODY

BUSHING

P0484237

P0484238

P0484239

P0484240

PR12M

OIL COVER

GEAR

SIGHT GLASS

GEAR

SCALE

SEPARATING RING

EXT RETAINING RING 35MM

ARBOR BOLT COVER

CAP SCREW M5-.8 X 12

PHLP HD SCR M5-.8 X 8

P0484282

P0484283

P0484284

P0484242

PSB33M

KNOB

SUPPORT

-38-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Head Parts List

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

285

286

287

288

289

290

291

292

293

294

295

296

297

298

299

300

301

302

303

304

P0484285

P0484286

P0484287

PS17M

FEED BASE

305

306

307

308

309

310

311

312

313

314

315

316

317

318

319

320

321

322

323

324

P0484305

PSB31M

P0484307

P0484308

P0484309

P0484310

P0484311

P0484312

P0484313

P6202

FEED COVER

SHAFT

CAP SCREW M8-1.25 X 25

WORM WHEEL

PHLP HD SCR M4-.7 X 6

REFERENCE MARKER

BRACKET

HANDLE BODY

P0484289

P0484290

P0484291

P0484292

P0484293

P0484294

P0484295

PN01M

HANDLE ROD

HANDLE BALL

SPECIAL NUT

COMPRESSION SPRING

KNOB

LOCK WASHER 30MM

TAPERED ROLLER BEARING

FLAT WASHER 75MM

QUILL

WORM GEAR

BALL BEARING 6202ZZ

EXT RETAINING RING 15MM

SEPARATING RING

WORM COVER

PR05M

HEX NUT M6-1

P0484316

P0484317

PSB24M

P0484319

P0484320

P0484321

PSS31M

P0484323

P0484324

PW03M

FLAT WASHER 6MM

HEX BOLT M6-1 X 50

TAPERED ROLLER BEARING

BEARING CUP

PB39M

CAP SCREW M5-.8 X 16

GRADUATED SCALE

KNOB M5-.8 X 12

BUSHING

P0484299

P0484300

P0484301

PFH19M

P0484303

P0484304

SPINDLE

FLAT HD SCR M4-.7 X 10

PINION SHAFT

SET SCREW M5-.8 X 8

HANDWHEEL

KEY 8 X 7 X 22

HANDLE

-39-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

Label Placement

406

401

405

402

404

403

407

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

401 PLABEL-11 SAFETY GLASSES LABEL

402 PLABEL-12 READ MANUAL LABEL

405 PLABEL-14 ELECTRICITY LABEL

406 P0484330

407 PPAINT-1

CUTTING/DAMAGE LABEL

403 P0484327

404 P0484328

MODEL NUMBER LABEL

GRIZZLY GREEN TOUCH UP PAINT

MACHINE ID & CONTROL PANEL LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine

MUST maintain the original location and readability of the labels on the machine. If any label is

removed or becomes unreadable, REPLACE that label before using the machine again. Contact

Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-40-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then

issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the

carton. We will not accept any item back without this number. Proof of purchase must accompany the

merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

-41-

G0484 Gear Head Mill/Drill

Download from Www.Somanuals.com. All Manuals Search And Download.

��

�

��

� ��

��

�

��

�

��

� ��

��

�

��

� ��

��

�

��

� ��

��

�

��

�

� ��

��

�

��

� ��

��

�

��

� ��

�

��

�

Download from Www.Somanuals.com. All Manuals Search And Download.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

��^��

��

��^��

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Inc Paint Sprayer 03289A User Manual
Grindmaster Coffee Grinder LCD2 1 SS User Manual
Grizzly Planer G1033X User Manual
Grizzly Scale T10008 User Manual
Grundig Car Stereo System UMS 4700 SPCD User Manual
Hamilton Beach Juicer 840097100 User Manual
Hamilton Electronics Plumbing Product A 6436 IBS User Manual
Harbor Freight Tools Lathe 44859 User Manual
Honeywell Network Card UDC 6300 User Manual
Hotpoint Oven BS89EK User Manual