MODEL G0555/G0555P
ULTIMATE 14" BANDSAW
OWNER'S MANUAL
model
g0555
model
g0555p
252923
Copyright © AUgUSt, 2002 By grizzly indUStriAl, inC., reviSed JUne, 2011 (tSJBCr)
WARNING: NO PORTION Of ThIS MANUAL MAy BE REPRODUcED IN ANy ShAPE
OR fORM WIThOUT ThE WRITTEN APPROvAL Of GRIzzLy INDUSTRIAL, INc.
For modelS mAnUFACtUred SinCe 5/11 #tr4508 printed in tAiWAn
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
INTRODUcTION............................................... 2
SEcTION 5: AccESSORIES......................... 41
manual Accuracy ........................................... 2
Contact info.................................................... 2
machine description ...................................... 2
identification................................................... 3
machine data Sheet ...................................... 4
SEcTION 6: MAINTENANcE......................... 43
Schedule...................................................... 43
Cleaning & protecting.................................. 43
lubrication ................................................... 44
redressing rubber tires............................. 44
SEcTION 1: SAfETy....................................... 6
Safety instructions for machinery .................. 6
Additional Safety for Bandsaws..................... 8
SEcTION 7: SERvIcE ................................... 45
troubleshooting ........................................... 45
v-Belt tension ............................................. 47
replacing v-Belt .......................................... 48
Shimming table........................................... 48
Wheel Alignment.......................................... 49
Blade lead................................................... 52
Blade tensioner........................................... 53
Fence Scale Calibration............................... 54
SEcTION 2: POWER SUPPLy........................ 9
SEcTION 3: SETUP ....................................... 12
needed for Setup......................................... 12
Unpacking.................................................... 12
hardware recognition Chart ....................... 13
inventory ...................................................... 14
Cleanup........................................................ 15
Site Considerations...................................... 16
Assembly ..................................................... 17
Blade Center tracking................................. 21
dust Collection............................................. 22
power Connection........................................ 23
test run ...................................................... 23
tensioning Blade ......................................... 24
Adjusting Blade Support Bearings............... 25
Adjusting Blade guide Bearings.................. 26
table tilt Calibration.................................... 28
Aligning table .............................................. 29
Aligning Fence ............................................. 30
SEcTION 8: WIRING...................................... 55
Wiring Safety instructions............................ 55
Wiring diagram ............................................ 56
SEcTION 9: PARTS....................................... 57
main ............................................................. 57
Stand............................................................ 60
Fence........................................................... 61
labels .......................................................... 62
WARRANTy AND RETURNS ........................ 65
SEcTION 4: OPERATIONS ........................... 31
operation overview..................................... 31
disabling & locking Switch.......................... 32
Workpiece inspection................................... 32
guide post ................................................... 33
table tilt ...................................................... 33
Blade Speed ................................................ 34
Blade information......................................... 35
Blade Change .............................................. 37
Basic Cutting tips........................................ 38
Cutting options............................................ 38
ripping......................................................... 38
Crosscutting................................................. 39
resawing ..................................................... 39
Cutting Curves............................................. 40
Stacked Cuts................................................ 40
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUcTION
Manual Accuracy
contact Info
We are proud to offer this manual with your new
machine! We've made every effort to be exact
with the instructions, specifications, drawings,
and photographs of the machine we used when
writing this manual. However, sometimes we still
make an occasional mistake.
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
Also, owing to our policy of continuous improve-
ment, your machine may not exactly match the
manual. If you find this to be the case, and the dif-
ference between the manual and machine leaves
you in doubt, check our website for the latest
manual update or call technical support for help.
Phone: (570) 546-9663
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Before calling, find the manufacture date of your
machine by looking at the date stamped into the
machine ID label (see below). This will help us
determine if the manual version you received
matches the manufacture date of your machine.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
Machine Description
Manufacture Date
of Your Machine
the bandsaw is a versatile woodworking tool that
is used to perform a wide variety of cuts in wood
stock, such as rip cuts, cross cuts, bevel cuts,
miter cuts, circular cuts, contour cuts, stacked
pattern cuts, etc.
the bandsaw blade is a continuous metal band
wrapped around two rotating wheels, which per-
forms the cut as it passes through the workpiece
and table. Adjustable blade guide and support
bearings keep the blade in position during this
operation.
For your convenience, we post all available man-
uals and manual updates for free on our website
of machine will be reflected in these documents
as soon as they are complete.
the included adjustable fence, miter gauge, and
tilting table support a wide variety of cutting
operations.
Note: the polar Bear model g0555p is the same
machine as the model g0555 except for the bril-
liant white color.
-2-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
l
A
m
p
n
B
o
d
Q
e
C
r
F
g
i
h
S
t
J
U
K
Front
view
rear
view
figure 1. g0555/g0555p identification.
A. Upper Wheel Cover
B. on/oFF Switch w/disabling padlock
c. Fence
D. Blade guard
E. Upper Blade guide Assembly
f. table pin
G. miter gauge Assembly
h. lower Wheel Cover
I. Fence lock lever
J. Front table lock Knob
K. Stand Assembly
L. Blade tension Adjustment Knob
M. Blade tension Quick release lever
N. guide post
O. guide post lock Knob
P. Blade tension Scale
Q. Blade tracking Adjustment Knob
R. table insert
S. rear table lock Knob
T. 4" dust port
U. motor
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.
-3-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
maCHiNe data
SHeet
model G0555/G0555P
ultimate 14" BaNdSaW
Product Dimensions:
Weight ...........................................................................................................................................................................167 lbs.
Length/Width/Height ................................................................................................................................. 263⁄8" x 301⁄4" x 661⁄2
Foot Print (Length/Width)....................................................................................................................................... 241⁄2" x 171⁄2
"
"
Shipping Dimensions:
Type ...........................................................................................................................................................................Cardboard
Content.......................................................................................................................................................................... Machine
Weight............................................................................................................................................................................198 lbs.
Length/Width/Height............................................................................................................................................44" x 21" x 20"
Electrical:
Switch.......................................................................................................................................................... On/Off Push Button
Switch Voltage ............................................................................................................................................................ 110/220V
Cord Length ..........................................................................................................................................................................6 ft.
Cord Gauge .................................................................................................................................................................16 gauge
Minimum Circuit Size ...................................................................................................................... 15A @ 110V, 10A @ 220V
Plug Included ........................................................................................................................................................................Yes
Recommended Plug Type ..........................................................................................................................NEMA 6-15 @220V
Included Plug Type ..................................................................................................................................................NEMA 5-15
Motors:
Main
Type ......................................................................................................................................... TEFC Capacitor Start Induction
Horsepower.........................................................................................................................................................................1 HP
Voltage......................................................................................................................................................................110V/220V
Prewired............................................................................................................................................................................. 110V
Phase................................................................................................................................................................................Single
Amps.............................................................................................................................................................................. 11/5.5A
Speed.........................................................................................................................................................................1725 RPM
Cycle ................................................................................................................................................................................. 60 Hz
Number Of Speeds ...................................................................................................................................................................1
Power Transfer ...........................................................................................................................................................Belt Drive
Bearings...............................................................................................................................................Shielded and Lubricated
Main Specifications:
Operation Information
Blade Speed...........................................................................................................................................1500, 3200 FPM
Table Tilt.............................................................................................................................................. Left 10°, Right 45°
Cutting Capacities
Maximum Cutting Height............................................................................................................................................... 6"
Max Capacity Left of Blade .......................................................................................................................................131⁄2
"
-4-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Information
Standard Blade Length..............................................................................................................................................931⁄2
"
"
"
Blade Length Range....................................................................................................................................... 921⁄2"–931⁄2
Blade Width Range ................................................................................................................................................ 1⁄8"–3⁄4
Upper Blade Guides................................................................................................................ Anti-Collision Ball Bearing
Lower Blade Guides................................................................................................................ Anti-Collision Ball Bearing
Guide Post Size.........................................................................................................................................0.865" (22mm)
Guide Post Type.............................................................................................................................................. Solid Steel
Table Information
Table Length ............................................................................................................................................................... 14"
Table Width ................................................................................................................................................................. 14"
Table Thickness ..........................................................................................................................................................11⁄2
"
Floor to Table Height............................................................................................................................................... 435⁄16"
Fence Information
Locks in Front..............................................................................................................................................................Yes
Locks in Rear ............................................................................................................................................................... No
Adjustable for Blade Lead...........................................................................................................................................Yes
Construction
Table Construction ................................................................................................................Precision Ground Cast Iron
Rip Fence..............................................................................................................................Deluxe Extruded Aluminum
Base Construction................................................................................................................................ Pre-Formed Steel
Body Construction..............................................................................................................................................Cast Iron
Upper Wheel ........................................................................................................... Computer Balanced Cast Aluminum
Lower Wheel ........................................................................................................... Computer Balanced Cast Aluminum
Tire Material ..........................................................................................................................................................Rubber
Wheel Cover......................................................................................................................................... Pre-Formed Steel
Paint .........................................................................................................................................................Powder Coated
Other Related Information
Wheel Diameter.........................................................................................................................................................133⁄4
"
Wheel Width.............................................................................................................................................................. 13⁄16"
Number of Dust Ports .....................................................................................................................................................1
Dust Port Size ............................................................................................................................................................... 4"
Mobile Base..........................................................................................................................................................G7314Z
Other Specifications:
ISO Factory................................................................................................................................................................. ISO 9001
Country Of Origin............................................................................................................................................................ Taiwan
Warranty...........................................................................................................................................................................1 Year
Serial Number Location .......................................................................................................... ID Label on Upper Wheel Cover
Customer Setup and Cleaning Time........................................................................................................................... 11⁄2 Hours
Features:
Includes Fence and Miter Gauge
Upper and Lower Ball Bearing Blade Guides
Deluxe Heavy-Duty Stand
Magnifying Window Over Fence Scale
Hinged Wheel Covers
4" Dust Port
6" Riser Block Available
-5-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 1: SAfETy
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULd result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand WEARING PROPER APPAREL. Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips which could cause a loss of work-
piece control.
this owner’s manual BEFORE using machine.
Untrained users can be seriously hurt.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are not approved safety glasses.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observiing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
HAzARdOUS dUST. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a NIOSH-approved respirator to
reduce your risk.
MENTAL ALERTNESS. Be mentally alert when
running machinery. Never operate under the
influence of drugs or alcohol, when tired, or when
distracted.
-6-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
-
DISCONNECTING POWER SUPPLY.-Always-dis- GUARDS & COVERS.- Guards- and- covers- can-
connect- machine- from- power- supply- before- ser-
vicing,- adjusting,- or- changing- cutting- tools- (bits,-
blades,-cutters,-etc.).-Make-sure-switch-is-in-OFF-
position-before-reconnecting-to-avoid-an-unexpect-
ed-or-unintentional-start.
protect-you-from-accidental-contact-with-moving-
parts-or-flying-debris.-Make-sure-they-are- prop-
erly-installed,-undamaged,-and-working-correctly-
before-using-machine.
NEVER STAND ON MACHINE.-Serious-injury-or-
accidental-contact-with-cutting-tool-may-occur-if-
machine-is-tipped.-Machine-may-be-damaged.
APPROVED OPERATION.- Untrained- operators-
can- be- seriously- hurt- by- machinery.- Only- allow-
trained- or- properly- supervised- people- to- use-
machine.-When-machine-is-not-being-used,-dis-
connect- power,- remove- switch- keys,- or- lock-out-
machine-to-prevent-unauthorized-use—especially-
around-children.-Make-workshop-kid-proof!
STABLE MACHINE. Unexpected-movement-dur-
ing-operations-greatly-increases-risk-of-injury-or-
loss- of- control.- Before- starting,- verify- machines-
are-stable-and-mobile-base-(if-used)-is-locked.
DANGEROUS ENVIRONMENTS. Do- not- use-
machinery- in- wet- or- rainy- locations,- cluttered-
areas,-around-flammables,-or-in-dark-areas.-Keep-
work-area-clean,-dry,-and-well-lighted.
AWKWARD POSITIONS.- Keep- proper- footing-
and-balance-at-all-times-when-operating-machine.-
Do-not-overreach!-Avoid-awkward-hand-positions-
that-make-workpiece-control-difficult-or-increase-
the-risk-of-accidental-injury.
ONLY USE AS INTENDED.- Only- use- machine-
for-its-intended-purpose.-Never-modify-machine-
for-a-purpose-not-intended-by-the-manufacturer!
UNATTENDED OPERATION. Never- leave-
machine-running-while-unattended.-Turn-machine-
off-and-ensure-all-moving-parts-completely-stop-
before-walking-away.
USE RECOMMENDED ACCESSORIES.-Consult-
this-owner’s-manual-or-the-manufacturer-for-rec-
ommended- accessories.- Using- improper- acces-
sories-will-increase-the-risk-of-serious-injury.
MAINTAIN WITH CARE.-Follow-all-maintenance-
instructions- and- lubrication- schedules- to- keep-
machine-in-good-working-condition.-An-improperly-
maintained-machine-increases-risk-of-injury.-
CHILDREN & BYSTANDERS. Keep- children-
and-bystanders-a-safe-distance-away-from-work-
area.-Stop-using-machine-if-children-or-bystand-
ers-become-a-distraction.
CHECK DAMAGED PARTS.- Regularly- inspect-
machine- for- damaged- parts,- loose- bolts,- mis-
adjusted- or- mis-aligned- parts,- binding,- or- any-
REMOVE ADJUSTING TOOLS.- Never- leave- other- conditions- that- may- affect- safe- operation.-
adjustment-tools,-chuck-keys,-wrenches,-etc.-in-or- Always-repair-or-replace-damaged-or-mis-adjust-
on-machine—especially-near-moving-parts.-Verify- ed-parts-before-operating-machine.
removal-before-starting!
MAINTAIN POWER CORDS. When-disconnect-
SECURING WORKPIECE.- When- required,- use-
clamps-or-vises-to-secure-workpiece.-A-secured-
workpiece-protects-hands-and-frees-both-of-them-
to-operate-the-machine.
ing- cord-connected- machines- from- power,- grab-
and-pull-the-plug—NOT-the-cord.-Pulling-the-cord-
may- damage- the- wires- inside.- Do- not- handle-
cord/plug-with-wet-hands.-Avoid-cord-damage-by-
keeping-it-away-from-heated-surfaces,-high-traffic-
areas,-harsh-chemicals,-and-wet/damp-locations.
FEED DIRECTION.-Unless-otherwise-noted,-feed-
work- against- the- rotation- of- blades- or- cutters.-
Feeding-in-the-same-direction-of-rotation-may-pull-
your-hand-into-the-cut.
EXPERIENCING DIFFICULTIES. If- at- any- time-
you- are- experiencing- difficulties- performing- the-
intended- operation,- stop- using- the- machine!-
Contact- our- Technical- Support- Department- at-
(570)-546-9663.
FORCING MACHINERY.-Do-not-force-machine.-
It-will-do-the-job-safer-and-better-at-the-rate-for-
which-it-was-designed.
-7-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety for Bandsaws
BLADE cONDITION. do not operate with dull, cUTTING TEchNIQUES. plan your operation
cracked or badly worn blade. dull blades require so the blade always cuts to the outside of the
more effort to perform the cut and increase the workpiece. do not back the workpiece away
risk of kickback. inspect blades for cracks and from the blade while the bandsaw is running,
missing teeth before each use.
which could cause kickback and personal injuries.
if you need to back the workpiece out, turn the
hAND PLAcEMENT. never position fingers or bandsaw oFF and wait for the blade to come to
hands in line with the blade. if the workpiece or a complete stop. do not twist or put excessive
your hands slip, serious personal injury could stress on the blade that could damage it.
occur.
LEAvING WORK AREA. never leave a machine
WORKPIEcE MATERIAL. this machine is running unattended. Allow the bandsaw to come
intended for cutting natural and man-made wood to a complete stop and use the padlock to disable
products, and laminate covered wood products. the machine before you leave it unattended.
this machine is not designed to cut metal, glass,
stone, tile, etc.
fEED RATE. to avoid the risk of the workpiece
slipping and causing operator injury, always feed
BLADE REPLAcEMENT. to avoid mishaps that stock evenly and smoothly. do not force or twist
could result in operator injury, make sure the blade the blade while cutting, especially when sawing
teeth face down toward the table and the blade is small curves.
properly tensioned and tracked before operating.
SMALL WORKPIEcE hANDLING. Always sup-
BLADE SPEED. moving the workpiece against port/feed the workpiece with push sticks, jig, vise,
a blade that is not at full speed could cause kick- or some type of clamping fixture. if your hands
back. Always allow the blade to come to full speed slip during a cut while holding small workpieces
before starting the cut.
with your fingers, amputation or laceration injuries
could occur.
GUARDS. the blade guard protects the operator
from the moving bandsaw blade. only operate BLADE cONTROL. to avoid serious personal
this bandsaw with the blade guard installed.
injury, do not attempt to stop or slow the blade
with your hand or the workpiece. Allow the blade
to stop on its own.
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. failure to do so could result in
serious personal injury, damage to equip-
ment, or poor work results.
Like all machinery there is potential danger
when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, seri-
ous personal injury may occur.
-8-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 2: POWER SUPPLy
Availability
circuit Information
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocu-
tion, fire, or equipment damage, installation work
and electrical wiring must be done by a qualified
electrician in accordance with all applicable codes
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
For your own safety and protection of
property, consult a qualified electrician if
you are unsure about wiring practices or
electrical codes in your area.
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuit—where only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
full-Load current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
circuit Requirements for 110v
This machine is prewired to operate on a 110V
power supply circuit that has a verified ground and
meets the following requirements:
full-Load current Rating at 110v...... 11 Amps
full-Load current Rating at 220v ....5.5 Amps
Nominal voltage ...............................110v/120v
cycle..........................................................60 hz
Phase........................................... Single-Phase
circuit Rating...................................... 15 Amps
Plug/Receptacle ............................. NEMA 5-15
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
circuit Requirements for 220v
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the requirements in the following section.
This machine can be converted to operate on a
220V power supply (refer to Voltage Conversion
instructions). This power supply must have a veri-
fied ground and meet the following requirements:
Nominal voltage .............................. 220v/240v
cycle..........................................................60 hz
Phase........................................... Single-Phase
circuit Rating...................................... 15 Amps
Plug/Receptacle ............................. NEMA 6-15
-9-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Requirements
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
SHOCK HAZARD!
Two-prong outlets do not meet the grounding
requirements for this machine. Do not modify
or use an adapter on the plug provided—if
it will not fit the outlet, have a qualified
electrician install the proper outlet with a
verified ground.
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
For 220V operation: The plug specified under
“Circuit Requirements for 220V” on the previous
page has a grounding prong that must be attached
to the equipment-grounding wire on the included
power cord. The plug must only be inserted into
a matching receptacle (see following figure) that
is properly installed and grounded in accordance
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
GROUNDED
6-15 RECEPTACLE
Current Carrying Prongs
For 110V operation: This machine is equipped
with a power cord that has an equipment-ground-
ing wire and a grounding plug (see following fig-
ure). The plug must only be inserted into a match-
ing receptacle (outlet) that is properly installed
and grounded in accordance with all local codes
and ordinances.
6-15 PLUG
Grounding Prong
figure 3. typical 6-15 plug and receptacle.
GROUNDED
5-15 RECEPTACLE
Grounding Prong
5-15 PLUG
Neutral Hot
figure 2. typical 5-15 plug and receptacle.
-10-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension cords
voltage conversion
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
the voltage conversion mUSt be performed by
a electrician or qualified service personnel. to
perform the voltage conversion, install the cor-
rect plug and rewire the motor to the new volt-
age, according to the provided wiring diagram on
Page 56.
Extension cords cause voltage drop, which may
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Note: If the diagram included on the motor con-
flicts with the one in this manual, the motor may
have changed since the manual was printed. Use
the diagram provided inside the motor wiring junc-
tion box.
Any extension cord used with this machine must
contain a ground wire, match the required plug
and receptacle, and meet the following require-
ments:
To convert the machine to 220v:
1. diSConneCt mAChine From poWer!
Minimum Gauge Size...........................14 AWG
Maximum Length (Shorter is Better).......50 ft.
2. replace the 5-15 plug on the power cord with
a 6-15 plug.
3. re-wire the motor as illustrated in the wiring
diagram.
-11-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 3: SETUP
Needed for Setup
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
the following are needed to complete the setup
process, but are not included with your machine.
Description
Qty
•
•
•
•
•
•
•
•
•
•
•
Safety glasses ............................................1
Cleaner/degreaser ......................As needed
disposable Shop rags................As needed
Additional people for lifting ......... At least 1
level............................................................1
hex Wrench 5mm........................................1
Wrench or Socket 10mm.............................2
Wrench or Socket 13mm.............................2
dust Collection System ...............................1
dust hose 4" ...............................................1
hose Clamps 4" ..........................................2
Wear safety glasses dur-
ing the entire setup pro-
cess!
This machine and its com-
ponents are very heavy.
Get lifting help or use
power lifting equipment
such as a forklift to move
heavy items.
Unpacking
your machine was carefully packaged for safe
transportation. remove the packaging materials
from around your machine and inspect it. if you
discover the machine is damaged, please imme-
diately call us at (570) 546-9663 for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
-12-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
hardware Recognition chart
-13-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Inventory
A
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
figure 4. Bandsaw assembly.
Shipping Inventory: (figures 4–6)
Qty
A. Bandsaw Assembly.....................................1
B. Upper Stand Braces....................................2
c. Stand top....................................................1
D. miter gauge Assembly................................1
E. Stand Sides.................................................2
f. table w/insert & table pin ..........................1
G. table trunnion.............................................1
h. table lock Knobs 3⁄8"-16 .............................2
I. lower Stand Braces....................................2
J. Front Fence rail..........................................1
K. rear Fence rail ..........................................1
L. Fence Assembly..........................................1
M. hardware (not Shown):
B
C
d
e
F
g
i
h
—hex Bolts m6-1 x 16 (Stand)................. 16
—Flat Washers 6mm (Stand)................... 16
—Flange nuts m6-1 (Stand) .................... 16
figure 5. other components.
3
—Stand Feet ⁄8"-16 x 2" (Stand)................ 4
—hex nuts 3⁄8"-16 (Stand Feet).................. 8
—Flat Washers 3⁄8" (Stand Feet)................ 8
—Carriage Bolts m8-1.25 x 16 (Stand) ...... 8
—Flange nuts m8-1.25 (Stand).................. 8
—hex Bolts m8-1.25 x 35 (Bandsaw) ........ 4
—Flat Washers 8mm (Bandsaw) ............... 8
—lock Washers 8mm (Bandsaw).............. 4
—hex nuts m8-1.25 (Bandsaw)................. 4
—hex Bolts m8-1.25 x 30 (trunnion) ......... 2
—lock Washers 8mm (trunnion)............... 2
—hex Bolt m8-1.25 x 80 (positive Stop).... 1
—hex nut m8-1.25 (positive Stop)............. 1
—Fence Stand-off m6-1 x 20 (Fence)....... 1
—lock handle m8-1.25 x 20 (Fence)......... 1
—Cap Screws m6-1 x 16 Black (Fence) .... 2
—hex Bolts m6-1 x 20 Black (Fence)........ 2
—lock Washers 6mm Black (Fence)......... 2
—Flat Washers 6mm Black (Fence) .......... 2
—hex nut m8-1.25 Black (Fence).............. 1
—hex nut m6-1 Black (Fence)................... 1
J
K
l
figure 6. Fence components.
NOTICE
If you cannot find an item on this list, care-
fully check the machine and the packaging
materials. Some of these items may be pre-
installed for shipping or become misplaced
during unpacking.
-14-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
cleanup
Gasoline or products
with low flash points can
explode or cause fire if
used to clean machin-
ery. Avoid cleaning with
these products.
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
Many cleaning solvents
are toxic if concentrat-
ed amounts are inhaled.
Only work in a well-venti-
lated area.
There are many ways to remove this rust preven-
tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-
turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces. Test all cleaners
in an inconspicuous area before using to
make sure they will not damage paint.
Before cleaning, gather the following:
•
•
•
•
Disposable Rags
Cleaner/degreaser (WD•40 works well)
Safety glasses & disposable gloves
Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1. Put on safety glasses.
2. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3. Wipe off the surfaces. If your cleaner/degreas-
er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
4. Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
-15-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Site considerations
Weight Load
Physical Environment
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
The physical environment where the machine is
operated is important for safe operation and lon-
gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20–95% (non-condensing); or the
environment is subject to vibration, shocks, or
bumps.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals,
or other hazards. Make sure to leave access to
a means of disconnecting the power source or
engaging a lockout/tagout device, if required.
Lighting
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
301⁄4
"
28"
Dust Hose
figure 7. minimum working clearances.
model g0555/g0555p (mfg. Since 5/11)
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach the remaining stand side to the assem-
bly, as shown in figure 9, with (8) m6-1 x 16
hex bolts, (8) 6mm flat washers, and (8) m6-1
flange nuts.
Assembly
Some metal parts may have
sharp edges that can cause
minor injury. Please exam-
ine the edges of all metal
parts BEfORE handling
them and be careful WhILE
handling them.
To assemble the bandsaw:
1. lay one stand side flat on a protective sur-
face, then attach the upper and lower stand
braces, as shown in figure 8, with (8) m6-1
x 16 hex bolts, (8) 6mm flat washers, and (8)
m6-1 flange nuts.
figure 9. Second stand side attached.
3. install the foot assemblies into the holes in
the bottom of the stand assembly, using (2)
Note: Only hand-tighten the stand fasteners
for now during these initial steps. Once the
stand is fully assembled you will be instructed
to fully tighten all fasteners.
3
⁄8"-16 hex nuts and (2) 10mm flat washers,
as shown in figure 10.
Note: Adjust the feet so that they are approxi-
mately the same height—this will make level-
ing the stand easier in a later step.
Upper
lower
Stand Brace
Stand Brace
x 8
x 4
figure 10. Stand foot installed (1 of 4).
-17-
Stand Side
figure 8. Upper and lower stand braces
attached to the stand side.
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. turn the stand assembly upright and attach
the top, as shown in figure 11, with (8)
m8-1.25 x 16 carriage bolts and (8) m8-1.25
flange nuts.
7. With the help of other people, lift the bandsaw
assembly onto the stand and align the mount-
ing holes.
8. Secure the bandsaw assembly to the stand
with (4) m8-1.25 x 35 hex bolts, (8) 8mm
flat washers, (4) 8mm lock washers, and (4)
m8-1.25 hex nuts, as shown in figure 13.
x 8
x 4
figure 11. Stand top attached.
5. Square up the stand components and fully
tighten all the fasteners.
figure 13. Bandsaw assembly attached to the
stand.
6. place the level on top of the stand assembly,
as shown in figure 12, then adjust the feet
up or down to make the stand top level from
side to side and front to back. make sure that
both hex nuts on the feet are tight against the
stand assembly.
9. position the table trunnion on the bandsaw,
as shown in figure 14, then secure it with the
(2) m8-1.25 x 30 hex bolts and (2) 8mm lock
washers.
x 2
trunnion
figure 12. leveling the stand.
figure 14. trunnion installed.
-18-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
10. thread the remaining m8-1.25 hex nut onto
the m8-1.25 x 80 positive stop hex bolt,
then thread the bolt into the trunnion so that
approximately 2" protrudes above the trun-
nion (see figure 15). this will allow the table
to rest approximately level when it is installed
during the following steps.
12. line up the blade with the table slot and move
the table around the blade until the blade is in
the center of the table, then turn the table 90˚
counterclockwise and rest it on the trunnions
so that the bolts protrude from the bottom of
the trunnions.
3
13. Secure the table by threading the (2) ⁄8"-16
table lock knobs onto the bolts, as shown in
figure 17.
2"
figure 15. positive stop installed.
11. remove the aluminum table insert from
the center of the table and remove the
table pin from the end of the table slot (see
figure 16).
figure 17. Securing table to the trunnion.
14. replace the table insert and pin removed in
Step 11. make sure the table insert sits flush
with the table surface.
insert
pin
figure 16. table insert and pin.
-19-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Attach the front fence rail to the table with
the (2) m6-1 x 20 hex bolts, (2) 6mm lock
washers, and (2) 6mm flat washers (see
figure 18).
17. thread (1) m8-1.25 hex nut onto the fence
lock handle, then thread the handle into the
fence and secure it in place by tightening the
hex nut against the fence.
Note: There is a small amount of vertical play
in the rail holes. Make sure to position the
rail evenly along its length before tightening
the hex bolts. This will allow the fence to ride
across the table with the proper amount of
clearance.
18. move the fence lock handle up, position
the fence face between the column and the
blade, as shown in figure 20, then place it
onto the front fence rail.
Use this Set
of threaded holes
figure 20. placing the fence onto the rails.
figure 18. Attaching the front fence rail.
19. thread the m6-1 hex nut onto the fence
stand-off, then thread it into the rear under-
side of the fence (see figure 21) so that
the fence rests the same height above the
table along its full length. tighten the hex nut
against the fence to secure the setting.
16. Attach the rear fence rail to the table with
the (2) black m6-1 x 16 cap screws (see
figure 19).
Stand-off
figure 19. Attaching the rear fence rail.
figure 21. Fence stand-off installed.
-20-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
tension
Adjustment
Knob
Blade center
Quick release
lever
Tracking
Blade tracking is affected by the tilt of the upper
wheel (known as center tracking) and the align-
ment of both wheels (known as coplanar track-
ing).
tracking
Adjustment
Knob
tension
Scale
the wheels on this bandsaw were aligned at the
factory, so center tracking is the only adjustment
that needs to be performed when the saw is new
(refer to the Wheel Alignment on Page 49 for
detailed instructions on coplanar tracking).
figure 22. Blade tension and center tracking
controls.
Note: Changes in the blade tension may change
the blade tracking. For best performance, regularly
check and maintain the proper blade tracking.
4. to tension the blade, pull the tension quick
release lever down to the horizontal position.
5. open the upper wheel cover, then spin the
upper wheel by hand at least three times and
watch how the blade rides on the crown of
the wheel. refer to the figure below for an
illustration of this concept.
To center track the blade:
1. diSConneCt BAndSAW From poWer!
2. Adjust the upper and lower blade guides
away from the blade (refer to Adjusting
Blade Guide Bearings later in this manual
for detailed instructions).
—If the blade rides on the center of
the crown, then the bandsaw is already
tracked properly and no additional adjust-
ments are needed. Skip to Step 9.
Note: When adjusting the blade tracking, the
blade must have a reasonable amount of ten-
sion to simulate operating conditions. After
the Test Run is successfully completed, you
will perform a thorough version of the follow-
ing steps to correctly tension the blade.
—If the blade does not ride on the center
of the crown, then continue with the next
step.
Blade Centered
on peak of Crown
3. move the quick release lever up to the verti-
cal position (see the following figure), then
use the blade tension adjustment knob to
bring the red marker to the correct mark on
the tension scale for the blade installed.
Blade
Centered
on Wheel
Wheel
Center trACKing
figure 23. profiles of blade properly center
tracking.
-21-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Unlock the blade tracking adjustment knob
so the knob will rotate for adjustments in the
next steps.
Dust collection
Note: The blade tracking adjustment knob
controls the tilt of the upper wheel which,
in turn, controls the center tracking of the
blade.
DO NOT operate this bandsaw without an ade-
quate dust collection system. This bandsaw
creates substantial amounts of wood dust
while operating. failure to use a dust collec-
tion system can result in short and long-term
respiratory illness.
7. Spin the upper wheel with one hand and use
the blade tracking adjustment knob with the
other hand to make the blade ride in the cen-
ter of the bandsaw wheel tire.
Recommended cfM at Dust Port: 400 cfM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
8. After the blade consistently rides in the center
of the wheel after several rotations, lock the
blade tracking adjustment knob to secure the
setting.
9. Close the upper wheel cover.
Note: For the best performance from your saw,
regularly maintain the proper tracking of the
blade.
To connect a dust collection hose:
1. Fit the dust hose over the dust port, as shown
in the figure below, and secure in place with a
hose clamp.
2. tug the hose to make sure it does not come
off.
Note: A tight fit is necessary for proper per-
formance.
figure 24. 4" dust hose attached to dust port.
model g0555/g0555p (mfg. Since 5/11)
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
Power connection
Test Run
After you have completed all previous setup
instructions and circuit requirements, the machine
is ready to be connected to the power supply.
once the assembly is complete, test run your
machine to make sure it runs properly and is
ready for regular operation.
To avoid unexpected startups or property dam-
age, use the following steps whenever connecting
or disconnecting the machine.
the test run consists of verifying the following:
1) the motor powers up and runs correctly, and
2) the safety disabling mechanism on the switch
works correctly.
connecting Power
1. Turn the machine power switch OFF.
if, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review
Troubleshooting on Page 45.
2. Insert the power cord plug into a matching
power supply receptacle. The machine is
now connected to the power source.
if you still cannot remedy a problem, contact our
tech Support at (570) 546-9663 for assistance.
To test run the machine:
1. make sure you have read the safety instruc-
tions at the beginning of the manual and that
the machine is set up properly.
2. make sure all tools and objects used during
setup are cleared away from the machine.
3. verify that the machine is operating correctly
by turning it ON.
figure 25. Connecting power.
Disconnecting Power
1. Turn the machine power switch OFF.
—When operating correctly, the machine
runs smoothly with little or no vibration or
rubbing noises.
2. Grasp the molded plug and pull it completely
out of the receptacle. Do not pull by the cord
as this may damage the wires inside.
—investigate and correct strange or unusual
noises or vibrations before operating the
machine further. Always disconnect the
machine from power when investigating or
correcting potential problems.
figure 26. Disconnecting power.
-23-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. turn the machine OFF.
Tensioning Blade
5. insert the switch disabling padlock through the
green on button, as shown in figure 27.
A properly tensioned blade is essential for making
accurate cuts, extending the life of the blade, and
making many other bandsaw adjustments.
Padlock
Note: Before you performed the Test Run, you
tensioned the blade according to the blade ten-
sion scale, which is only an approximate tension.
The following procedure fine tunes the blade ten-
sion to ensure more accurate cutting results.
Shaft
To tension the bandsaw blade:
figure 27. Switch disabling padlock inserted into
on button.
1. make sure the blade is properly center track-
ing as instructed in the Blade Tracking sub-
section previous to the Test Run.
6. press the green on button to test the dis-
abling feature on the switch.
2. to tension the blade, pull the tension quick
release lever down to the horizontal position.
—if the machine does not start, the switch
disabling feature is working as designed.
tension
Adjustment
Knob
Quick release
lever
—if the machine starts, immediately stop it.
the switch disabling feature is not working
correctly. this safety feature must work
properly before proceeding with regular
operations. Call tech Support for help.
tension
Scale
figure 28. Blade tension controls.
3. turn the bandsaw ON.
4. Slowly rotate the blade tension adjustment
knob counterclockwise one quarter of a turn
at a time—this will release blade tension.
When you see the blade start to flutter, stop
decreasing tension.
now, slowly rotate the knob clockwise to
increase the tension until the blade stops flut-
tering, then tighten the blade tension adjust-
ment knob one more quarter of a turn.
-24-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. look at what the tension gauge reads and
use that as a guide for tensioning that blade
in the future.
Tool Needed
Wrench 10mm ....................................................1
Qty
To adjust the support bearings:
Note: Do not rely on this setting for long
periods of time because the blade will stretch
with use.
1. make sure the blade is tracking properly and
is correctly tensioned.
Additionally, with extended use, the blade
tensioning system may need to be reset for
correct operation. Refer to the Resetting
Blade Tensioner in the Service section on
this manual.
2. diSConneCt BAndSAW From poWer!
3. Familiarize yourself with the support bearing
controls shown in the figure below.
Knurled
Knob
Assembly lock Bolt
When using a 3⁄4" blade, the blade tensioning
system may need to be reset for correct
operation. Refer to Blade Tensioner on Page
53 for detailed instructions.
Support
Bearing
Adjusting Blade
Support Bearings
thumbscrew
figure 29. Support bearing controls.
4. loosen the guide assembly lock bolt so that
the support bearing can be rotated perpen-
dicular to the blade in the next step.
the support bearings are positioned behind the
blade to prevent it from deflecting backward dur-
ing cutting operations. proper adjustment of the
support bearings is an important part of making
accurate cuts and keeps the blade teeth from
coming in contact with the blade guides while
cutting.
5. rotate the blade guide assembly until the
face of the support bearing is perpendicu-
lar to the blade, as illustrated in the figure
below.
there are support bearings on the upper and
lower blade guide assemblies. Both adjust in the
same manner.
Bandsaw
Blade
Whenever changing a blade or adjusting
tension and tracking, the upper and lower
support bearings and blade guides must be
re-adjusted before cutting operations.
Support
Bearing
figure 30. the face of the support bearing must
be perpendicular (90°) to the blade.
-25-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Tighten the guide assembly lock bolt to
Adjusting Blade
Guide Bearings
secure the setting.
7. Loosen the thumbscrew on the support bear-
ing adjustment shaft.
Properly adjusting the blade guides provides side-
to-side support to help keep the blade straight
while cutting, which is essential to making accu-
rate cuts.
8. Use the knurled knob to position the support
bearing approximately 0.016" behind the
blade, as illustrated in the figure below.
Tool Needed
Hex Wrench 4mm...............................................2
Qty
0.016''
To adjust the upper and lower blade guides:
1. Make sure that the blade is tracking properly
and is correctly tensioned.
2. DISCONNECT BANDSAW FROM POWER!
3. Familiarize yourself with the blade guide con-
trols shown in the figure below.
Figure 31. The face of the support blade must
be approximately 0.016" behind the blade.
Guide Bearing
Adjustment
Cap Screws
Tip: To quickly gauge this setting, fold a crisp
dollar bill in half twice (when folded tightly,
four thicknesses of a dollar bill is approxi-
mately 0.016"). Place the folded dollar bill
between the support bearing and the blade,
as shown in the figure below.
Knurled
Knob
Thumbscrew
Locking
Cap Screw
Figure 33. Blade guide bearing controls.
Figure 32. Dollar bill folded twice to make a
quick 0.016" gauge.
9. Tighten the thumbscrew to lock the support
bearing in place.
-26-
Model G0555/G0555P (Mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. loosen the thumbscrew shown in the figure
above, then use the knurled knob to adjust
the guide bearings laterally so that the bear-
ing faces are just behind the blade gullet, as
illustrated in the following figure.
6. loosen both cap screws behind the guide
bearings, then rotate the adjustment cap
screws so the bearings evenly and lightly
touch the sides of the blade (see the illustra-
tion in the following figure).
Note: When the blade guide bearings are
properly adjusted against the blade, they
should still be able to rotate.
Blade
Guide
Bearing
Blade
Gullets
figure 34. the blade guide bearings should be
positioned just behind the blade gullets.
figure 35. Blade guide bearings evenly and
lightly touching the sides of the blade.
Note: With wider blades, it may not be pos-
sible to bring the guide bearings just behind
the blade gullets. In that case, position them
as far forward as possible without allowing
the guide bearing housing to touch the back
of the blade.
7. While keeping the adjustment cap screws
from turning with one hex wrench, re-tighten
the locking cap screws to secure the set-
tings.
To reduce the risk of damage to the blade or
guide bearings, make sure that the bearings
do not contact the blade teeth when the
blade is deflected backward.
Whenever changing a blade or adjusting the
blade tension or tracking, the support and
guide bearings must be re-adjusted before
resuming operation.
5. When you are satisfied with the lateral adjust-
ment of the guide bearings, re-tighten the
thumbscrew to secure the setting.
-27-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Completely raise the upper blade guide
assembly, then place the machinist's square
flat on the table and against the side of the
blade, as illustrated in the figure below.
Table Tilt calibration
When properly adjusted, the positive stop bolt
enables the table to be quickly returned perpen-
dicular with the blade.
to tilt the table to the left, the positive stop bolt
must be lowered from its correct height, then re-
adjusted after the table is returned to 0°.
Square
Table
Positive
Stop
positive
Stop Bolt
figure 37. Using a square to adjust the table
perpendicular to the side of the blade.
6. raise or lower the positive stop bolt until the
table is perpendicular to the side of the blade,
then re-tighten the hex nut against the cast-
ing to secure the setting.
7. rest the table on the positive stop bolt, then
re-tighten the table lock knobs to secure the
table perpendicular to the side of the blade.
figure 36. positive stop bolt set at 90° (viewed
from behind the table).
Tools Needed
Qty
8. observe the position of the table tilt pointer
on the tilt scale located underneath the front
of the table (see the figure below).
Wrench 13mm ....................................................1
phillips Screwdriver #2 .......................................1
machinist's Square .............................................1
To set the positive stop 90˚ to the blade:
1. make sure the blade is correctly tensioned as
described in the Tensioning Blade subsec-
tion earlier in this manual.
2. diSConneCt BAndSAW From poWer!
tilt Scale
3. loosen the two table lock knobs that secure
the table to the trunnions.
pointer
4. loosen the hex nut that locks the positive
stop bolt in place.
figure 38. location of the table tilt scale.
9. if the pointer is not correctly positioned at the
0° mark, then loosen the pointer screw, posi-
tion the pointer at the 0° mark, and re-tighten
the screw to hold it in place.
-28-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Use the fine ruler to measure the distance
from the straightedge and the miter slot along
the full depth of the table.
Aligning Table
to ensure cutting accuracy when the table is first
installed, the table should be aligned so the miter
slot is parallel to the bandsaw blade.
—if the distances are the same, no further
adjustments are required.
—if the distances are different, continue with
Step 6.
Tools Needed
Qty
Straightedge 2' ...................................................1
Fine ruler...........................................................1
masking tape .....................................As needed
Wrench 10mm ....................................................1
6. loosen the six flange bolts that secure the
table to the trunnion brackets (see the figure
below).
To align the table to the blade:
1. make sure the blade is correctly tensioned as
described in the Tensioning Blade subsec-
tion earlier in this manual.
2. diSConneCt BAndSAW From poWer!
3. make sure the table is perpendicular to the
side of the blade and locked in place.
Flange Bolts
(3 of 6)
4. place an accurate straightedge along the
blade. the straightedge should lightly touch
both the front and back of the blade (see
figure 39).
figure 40. location of trunnion bracket flange
bolts.
Note: Make sure the straightedge does not
go across a tooth.
7. Shift the table so that the distances are equal
between the straightedge and miter slot along
the full depth of the table.
8. taking care not to move the table further, re-
tighten the flange bolts.
9. verify the setting and, if necessary, repeat
this procedure until you are satisfied with the
adjustment.
figure 39. measuring for table-to-blade
parallelism.
-29-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. loosen the four fence adjustment cap screws
shown in the figure below, adjust the fence
parallel to the miter slot, then re-tighten the
cap screws to secure the setting.
Aligning fence
to ensure accurate cutting when using the fence,
the face of the fence must be parallel to the table
miter slot and, thus, to the side of the blade.
Cap Screws
Tools Needed
Qty
hex Wrench 5mm...............................................1
To align the fence parallel with the miter slot:
1. make sure the miter slot is parallel with the
blade, as instructed in the previous Aligning
Table procedure.
2. diSConneCt BAndSAW From poWer!
3. install the fence on the right side of the blade,
even with the edge of the miter slot, then lock
it in place.
figure 41. location of the fence adjustment cap
screws.
—if the fence is parallel with the miter slot, no
adjustment is necessary.
—if the fence is not parallel with the miter
slot, proceed to Step 4.
-30-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 4: OPERATIONS
To complete a typical operation, the operator
does the following:
Operation Overview
1. examines the workpiece to make sure it is
suitable for cutting.
The purpose of this overview is to provide the nov-
ice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
2. Adjusts the fence for the width of the cut and
then locks it in place.
3. Adjusts the table tilt, if necessary, to the cor-
rect angle of the desired cut.
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual and seek additional training from expe-
rienced machine operators, and do additional
research outside of this manual by reading "how-
to" books, trade magazines, or websites.
4. loosens the guide post lock knob, adjusts
the upper blade guide height to just clear the
workpiece, then re- tightens the guide post
lock knob.
5. Checks to make sure the workpiece can safe-
ly pass all the way through the blade without
interference from other objects.
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before operating.
6. puts on safety glasses and a respirator.
7. Starts the dust collector and bandsaw.
8. holds the workpiece firmly and flatly against
both the table and fence, and then pushes
the workpiece into the blade at a steady and
controlled rate until the workpiece moves
completely beyond the blade.
Damage to your eyes and lungs could result
from using this machine without proper pro-
tective gear. Always wear safety glasses and
a respirator when operating this machine.
the operator is very careful to keep fingers
away from the blade and uses a push stick to
feed narrow workpieces.
9. Stops the bandsaw.
NOTICE
If you have never used this type of machine
or equipment before, WE STRONGLy REc-
OMMEND that you read books, review
industry trade magazines, or get formal
training before beginning any projects.
Regardless of the content in this section,
Grizzly Industrial will not be held liable for
accidents caused by lack of training.
-31-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Disabling & Locking
Switch
Workpiece
Inspection
The ON/OFF switch can be disabled and locked
by inserting a padlock through the ON button,
as shown. Locking the switch in this manner can
prevent unauthorized operation of the machine,
which is especially important if the machine is not
stored inside an access-restricted building.
Some workpieces are not safe to cut or may
require modification before they are safe to cut.
Before cutting, inspect all workpieces for the
following:
•
Material Type: this machine is intended for
cutting natural and man-made wood prod-
ucts, laminate covered wood products, and
some plastics. Cutting drywall or cementi-
tious backer board creates extremely fine
dust and may reduce the life of the bearings.
this machine is not designed to cut metal,
glass, stone, tile, etc.; cutting these materials
with a table saw may lead to injury.
IMPORTANT: Locking the switch with a padlock
only restricts its function. It is not a substitute
for disconnecting power from the machine when
adjusting or servicing.
Padlock
Shaft
•
Foreign Objects: nails, staples, dirt, rocks
and other foreign objects are often embed-
ded in wood. While cutting, these objects
can become dislodged and hit the operator,
cause kickback, or break the blade, which
might then fly apart. Always visually inspect
your workpiece for these items. if they can't
be removed, do not cut the workpiece.
figure 42. Switch disabled by a padlock.
•
Large/Loose Knots: loose knots can
become dislodged during the cutting opera-
tion. large knots can cause kickback and
machine damage. Choose workpieces that
do not have large/loose knots or plan ahead
to avoid cutting through them.
children or untrained people can be
seriously injured by this machine. This
risk increases with unsupervised operation.
To help prevent unsupervised operation,
disable and lock the switch before leaving
machine unattended! Place key in a well-
hidden or secure location.
•
Wet or "Green" Stock: Cutting wood with a
moisture content over 20% causes unneces-
sary wear on the blades, increases the risk of
kickback, and yields poor results.
•
Excessive Warping: Workpieces with exces-
sive cupping, bowing, or twisting are danger-
ous to cut because they are unstable and
often unpredictable when being cut. do not
use workpieces with these characteristics!
NOTICE
The padlock shaft diameter is important to
the disabling function of the switch. With
any padlock used to lock the switch, test
the switch after installation to ensure that it
is properly disabled.
•
Minor Warping: Workpieces with slight cup-
ping can be safely supported if the cupped
side is facing the table or the fence. on
the contrary, a workpiece supported on the
bowed side will rock during a cut and could
cause kickback or severe injury.
0.12"–0.15"
-32-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide Post
Table Tilt
the guide post, shown in the figure below, con-
nects the upper blade guide assembly and blade
guard to the bandsaw.
the table can be tilted when making angle or
bevel cuts.
Note: When tilting the table to the left, the positive
stop bolt must be lowered. Be sure to re-adjust it
when returning the table to be perpendicular with
the blade.
the guidepost allows these components to be
positioned above the workpiece at a distance that
provides the greatest support to the blade and
minimizes operator exposure to the blade. We
recommend positioning the blade guides so that
they just clear the workpiece.
To tilt the table:
1. diSConneCt BAndSAW From poWer!
2. loosen both table lock knobs underneath the
table.
guide
post
3. Use the table tilt scale underneath the front of
the table or a protractor against the table and
blade to tilt the table to the desired degree,
then re-tighten the lock knobs.
guide post
lock Knob
figure 43. guide post and lock knob.
To adjust the height of the guide post:
1. make sure that the blade tension, blade
tracking, support bearings, and blade guide
bearings are adjusted correctly.
2. diSConneCt BAndSAW From poWer!
3. loosen the guide post lock knob, then adjust
the height of the guide post so that the blade
guide assembly just clears the workpiece.
4. re-tighten the lock knob to secure the set-
ting.
-33-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Speed
Adjustment
Cap Screw
the model g0555/g0555p offers blade speeds
of 1500 and 3200 Fpm. For general woodwork-
ing and most cutting operations, we recommend
using the 3200 Fpm speed. Keep in mind, the
results from different speeds are related to the
type of workpiece, the blade being used for the
operation, and the feed rate.
hinge
Cap Screw
Use the chart below as a general guide to
blade speed:
figure 44. locations of the motor adjustment
and hinge cap screws.
Blade Speed
Type of cutting Operation
(fPM)
3. move the motor so that the adjustment cap
screw slides to the right of the slot. this will
release the tension on the ribbed v-belt.
most Species of Wood
Super dense hardwood
Fast/Average Feed rate
requires Slow Feed rate
rough edges Acceptable
requires Smooth edges
Quick, production Cuts
detailed, intricate Cuts
3200
1500
3200
1500
3200
1500
3200
1500
4. position the v-belt belt on the pulleys as illus-
trated in figure 45 for the desired speed.
Note: Make sure the ribs of the V-belt are
well seated in the pulley grooves.
Speed changes are made by re-positioning the
ribbed v-belt on the pulleys.
Wheel Pulley
Motor Pulley
Tools Needed
Qty
hex Wrench 6mm...............................................1
To change the blade speed:
1. diSConneCt BAndSAW From poWer!
3200
FPM
1500
FPM
2. open the lower wheel cover and loosen
the motor mount adjustment and hinge cap
screws shown in figure 44.
figure 45. drive belt position for the different
speeds.
5. move the motor so that the adjustment cap
screw slides to the left of the slot.
6. Apply enough pressure on the motor so that
1
there is approximately ⁄4" deflection of the
v-belt with moderate pressure from your fin-
ger between the pulleys, then re-tighten the
adjustment and hinge cap screws.
7. Close the lower wheel cover before re-con-
necting the bandsaw to power.
-34-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Straight cutting: Use the largest width blade
that you own. large blades excel at cutting
straight lines and are less prone to wander.
Blade Information
Blade Dimensions
Tooth Style
the figure below illustrates the three main blade
tooth styles:
length range................................... 921⁄2"–931⁄2
Width range..............................................1⁄8"–3⁄4
"
"
Selecting the right blade requires a knowledge
of the various blade characteristics to match the
blade with the particular cutting operation.
Blade Length
measured by the circumference, blade lengths
are usually unique to the brand of your bandsaw
and the distance between wheels. refer to the
Accessories section later in this manual for blade
replacements from grizzly.
Raker
Skip
Hook
Blade Width
measured from the back of the blade to the tip of
the blade tooth (the widest point), blade width is
often the first consideration given to blade selec-
tion. Blade width dictates the largest and smallest
curve that can be cut, as well as how accurately it
can cut a straight line.
figure 47. main blade tooth styles.
•
Raker: Considered to be the standard
because the tooth size and shape are the
same as the tooth gullet. the teeth on raker
blades usually are very numerous, have no
angle, and produce cuts by scraping the
material. As a result, smooth cuts can be
achieved without cutting fast or generating
more heat than other tooth types.
Always pick the size of blade that best suits your
application.
•
curve cutting: Use the chart in the figure
below to determine the correct blade for
curve cutting. determine the smallest radius
curve that will be cut on your workpiece and
use the corresponding blade width.
•
•
Skip: Similar to a raker blade that is missing
every other tooth. Because of the design,
skip toothed blades have a much larger gullet
than raker blades, and therefore, cut faster
and generate less heat. however, these
blades also leave a rougher cut than raker
blades.
hook: the teeth have a positive angle (down-
ward) which makes them dig into the material,
and the gullets are usually rounded for easier
waste removal. these blades are excellent
for the tough demands of resawing and rip-
ping thick material.
Cutting Radius
figure 46. recommended cutting radius per
blade width.
-35-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Tooth Pitch
Blade Breakage
measured as tpi (teeth per inch), tooth pitch
determines the number of teeth. more teeth per
inch (fine pitch) will cut slower, but smoother; while
fewer teeth per inch (coarse pitch) will cut rougher,
but faster. As a general rule, choose blades that
will have at least three teeth in the material at all
times. Use fine-pitched blades on harder woods
and coarse-pitched blades on softer woods.
many conditions may cause a bandsaw blade to
break. Blade breakage is unavoidable, in some
cases, since it is the natural result of the peculiar
stresses that bandsaw blades are subjected to.
Blade breakage is also due to avoidable circum-
stances. Avoidable breakage is most often the
result of poor care or judgement on the part of the
operator when mounting or adjusting the blade or
blade guides.
Blade care
The most common causes of blade breakage
A bandsaw blade is a thin piece of steel that is
subjected to tremendous stresses when cutting.
you can obtain longer use from a bandsaw blade
if you give it fair treatment and always use the
appropriate feed rate for your operation. Be sure
to select blades with the proper width, style, and
pitch for each application. the wrong choice of
blades will often produce unnecessary heat which
will shorten the life of your blade.
are:
•
•
Faulty alignment/adjustment of the guides.
Forcing/twisting a wide blade around a short
radius.
Feeding the workpiece too fast.
dull teeth or damaged tooth set.
over-tensioned blade.
•
•
•
•
Upper blade guide assembly set too high
above the workpiece.
A clean blade will perform much better than a dirty
blade. dirty or gummed up blades pass through
the cutting material with much more resistance
than clean blades. this extra resistance also
causes unnecessary heat. resin/pitch cleaners
are excellent for cleaning dirty blades.
•
•
Using a blade with a lumpy or improperly fin-
ished braze or weld.
Continuously running the bandsaw when not
in use.
leaving blade tensioned when not in use.
Using the wrong tpi for the workpiece thick-
ness. (the general rule of thumb is three
teeth in the workpiece at all times.)
•
•
-36-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Installation
1. diSConneCt BAndSAW From poWer!
Blade change
2. perform Steps 2–6 in the previous Blade
Removal procedure.
Always disconnect power
to the machine when
changing blades. failure
to do this may result in
serious personal injury.
3. put on heavy leather gloves, position the
blade so that the teeth are facing to the
right and down toward the table, then slide it
through the table slot.
Note: If the teeth will not point downward
in any orientation, the blade is inside-out.
Remove the blade and twist it right side-out.
Bandsaw blades are sharp
and can quickly cut fingers
and hands. To reduce the
risk of this type of injury,
ALWAySwearheavyleather
gloves when handling these
blades.
4. rotate the blade 90°, then slip it over the
wheels while making sure it is properly
positioned between the blade guards and
guides.
5. Use the blade tension adjustment knob to
bring the red marker to the correct blade
width mark on the tension scale, then pull the
blade tension quick release lever down to the
horizontal position.
Blade Removal
1. diSConneCt BAndSAW From poWer!
—if you are having difficulty pulling the
quick release lever down or the blade is
a different length from the previous blade,
adjust the blade tensioner as instructed
in the Blade Tensioner subsection on
Page 53. then, continue with Step 6.
2. move the blade tension quick release lever
up to release blade tension.
3. Adjust the upper blade guide assembly all
the way up and move the blade guides com-
pletely away from the blade.
—if you successfully pull the quick release
lever down and the blade is properly ten-
sioned, continue with Step 6.
4. remove the fence and miter gauge from the
table, then remove the table insert and the
table pin.
6. Check and adjust the blade tracking.
5. open the upper and lower wheel covers.
7. Adjust the support bearings and the upper/
lower blade guides.
6. put on heavy leather gloves, then slip the
blade off the wheels, rotate it 90°, and slide it
through the table slot and off the machine.
8. Close the wheel covers, and replace the table
insert and table pin.
-37-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic cutting Tips
Ripping
here are some basic tips to follow when oper-
ating the bandsaw:
"ripping" means cutting with the grain of the
wood stock. For plywood and other processed
wood, ripping simply means cutting down the
length of the workpiece.
•
•
•
•
replace, sharpen, and clean blades as nec-
essary. make adjustments periodically to
keep the saw running in top condition.
To make a rip cut:
Use light and even pressure while cutting.
light contact with the blade eases line follow-
ing and prevents undue friction.
1. Adjust the fence to match the width of the
cut on your workpiece, then lock the fence in
place.
Avoid twisting the blade when cutting around
tight corners. Allow the blade to saw around
the corners.
2. Adjust the blade guide assembly to the prop-
er height above the workpiece.
3. After all safety precautions have been met,
turn the bandsaw ON and wait for it to come
to full speed. Slowly feed the workpiece into
the blade and continue with the cut until the
blade is completely through the workpiece.
the figure below shows an example of a rip-
ping operation.
misusing the saw or using incorrect tech-
niques is unsafe and results in poor cuts.
remember—the blade does the cutting with
the operator’s guidance.
cutting Options
Note: If you cut narrow pieces, use a push
stick to protect your fingers.
the bandsaw is capable of performing the follow-
ing cuts:
•
•
•
•
•
miters
•
•
•
•
•
Compound Angles
Complex Curves
duplicate parts
Circles
Angles
resaw
ripping
Crosscutting
Beveled Curves
figure 48. example of a ripping operation.
NEvER place fingers or hands in the line
of cut. If you slip, your hands or fingers
may go into the blade. ALWAyS use a push
stick when ripping narrow pieces. failure to
follow these warnings may result in serious
personal injury!
-38-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
crosscutting
Resawing
Crosscutting is the process of cutting across the
grain of wood. For plywood and other processed
wood, crosscutting simply means cutting across
the width of the material.
"resawing" means cutting the thickness of a
board into two or more thinner boards (see the fig-
ure below for an example). the maximum board
width that can be resawn is limited by the maxi-
mum cutting height of the bandsaw.
To make a 90˚ crosscut:
one of the most important considerations for
resawing is blade selection—a wide blade cuts
straighter and is less prone to blade lead (see the
Blade Lead subsection later in this manual for
more information).
1. mark the workpiece on the edge where you
want to begin the cut.
2. Adjust the blade guide assembly to the cor-
rect height and make sure the miter gauge is
set to 0° (or other angle for angled cuts).
For most applications, use a blade with a hook
or a skip tooth style. Choose blades with fewer
teeth-per-inch (from 3 to 6 tpi), because they
offer larger gullet capacities for clearing sawdust,
reducing heat buildup, and reducing strain on the
motor.
3. move the fence out of the way. place the
workpiece evenly against the miter gauge,
then line up the mark with the blade.
4. After all safety precautions have been met,
turn the bandsaw ON and wait for it to come
to full speed. Slowly feed the workpiece into
the blade and continue the cut until the blade
is all the way through the workpiece. the
figure below shows an example of a crosscut-
ting operation.
figure 50. example of a resawing operation.
When resawing thin pieces, a wandering
blade (blade lead) can tear through the side
of the workpiece, exposing your hands to
the blade teeth. Always use push blocks
when resawing and keep your hands clear
of the blade.
figure 49. example of a crosscutting operation
with the miter gauge.
-39-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
cutting curves
Stacked cuts
one of the benefits of a bandsaw is its ability to
cut multiple copies of a particular shape by stack-
ing a number of workpieces together. Before mak-
ing stacked cuts, ensure that the table is perpen-
dicular (90°) to the blade—otherwise, any error
in this setting will be compounded in the upper
workpieces.
When cutting curves, simultaneously feed and
turn the stock carefully so that the blade follows
the layout line without twisting. Use either a nar-
rower blade or a blade with more tpi (teeth per
inch), or make more relief cuts, to avoid having to
back the workpiece away from the blade, espe-
cially if the curve is sharp.
To complete a stacked cut:
Always make short cuts first, then proceed to
the longer cuts. relief cuts will also reduce the
chance that the blade will be pinched or twisted.
relief cuts are cuts made through the waste
portion of the workpiece and are stopped at the
layout line. As you cut along the layout line, waste
wood is released from the workpiece, alleviating
any pressure on the back of the blade. relief cuts
also make backing the workpiece out easier once
the saw blade has come to a stop, if needed.
1. Align your pieces from top to bottom to
ensure that each piece has adequate scrap
to provide a clean, unhampered cut.
2. Secure all the pieces together in a manner
that will not interfere with the cutting. hot
glue on the edges works well, as do brad
nails through the waste portion. (Be careful
not to cut into the brads or you may break the
blade!)
3. on the face of the top piece, lay out the
shape you intend to cut.
The list below displays blade widths and
the corresponding minimum radii for those
blade widths.
4. make relief cuts perpendicular to the out-
line of your intended shape in areas where
changes in blade direction could strain the
woodgrain or cause the blade to bind.
Width
Min. Radius
1
⁄
8"....................................1⁄8
"
"
3⁄16"...................................3⁄8
1
⁄
⁄
⁄
⁄
⁄
4''....................................5⁄8''
3
1
5
3
8''....................................11⁄4''
2''....................................21⁄2''
8''....................................33⁄4''
4''....................................51⁄2''
5. Cut the stack of pieces as though you were
cutting a single piece. Follow your layout line
with the blade kerf on the waste side of your
line (see the figure below for an example of
stacked cut setup).
figure 51. example of a stacked cut setup.
model g0555/g0555p (mfg. Since 5/11)
-40-
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCeSSorieS
SEcTION 5: AccESSORIES
Bandsaw Blades
grizzly bandsaw blades are made from top quality
saw steel manufactured to precise tolerances with
guaranteed welds for blades that last longer and
produce smoother cuts.
Some aftermarket accessories can be
installed on this machine that could cause
it to function improperly, increasing the risk
of serious personal injury. To minimize this
risk, only install accessories recommended
for this machine by Grizzly.
Model Length Width
TPI
Gauge
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
0.025
1
g5152
g5153
g5154
g5155
g5156
g5157
g5158
g5159
g5160
g5161
g5162
g5163
g5164
g5165
g5166
g5167
g5168
g5169
g5170
g5171
g5172
g5173
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
931⁄2
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
⁄
8
"
14 raker
18 raker
4 Skip
1
⁄
8"
3⁄16"
3⁄16"
10 raker
14 raker
4 hook
3⁄16"
NOTICE
Refer to the newest copy of the Grizzly
catalog for other accessories available for
this machine.
1
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
⁄
4"
4"
4"
4"
4"
8"
8"
8"
8"
2"
2"
2"
2"
2"
4"
4"
4
"
1
1
1
1
3
3
3
3
1
1
1
1
1
3
3
3
6 hook
10 raker
14 raker
18 raker
4 hook
6 hook
Order Online at grizzly.com®
10 raker
14 raker
3 hook
4 hook
6 hook
h3051—6" Extension Block Kit for G0555
h3051P— 6" Extension Block Kit for G0555P
increase your cutting capacity from 6" to 12" cut-
ting height with this bolt-on 6" extension block kit.
includes all necessary hardware plus extended
blade guard and 105" x 3⁄8" x 6 tpi blade. We also
carry a full line of 105" blades!
10 raker
14 raker
3 hook
6 hook
10 raker
G1928—Bandsaw handbook
this is the bandsaw bible. Covers step-by-step
instructions for basic/advanced cutting tech-
niques. Also includes advanced maintenance,
service and troubleshooting procedures, as well
as information on bandsaw history/design and
blade metallurgy. 320 pages.
figure 52. h3051 extension Block Kit.
figure 53. Bandsaw handbook.
-41-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
G7315z—Super heavy-Duty ShOP fOX®
Mobile Base
G1163—1hP floor Model Dust collector
G0710—1hP Wall-Mount Dust collector
G3591—30 Micron Replacement Bag
this patented, super heavy-duty mobile machine
base is the strongest mobile base on the mar-
ket. 18" x 241⁄2" minimum and adjusts to 281⁄2" x
331⁄2". maximum 1200 lb. capacity. this base is
extremely stable with outrigger type supports and
a four wheel system. Weighs 38 lbs.
h4340—3.0 Micron Upgrade Bag
excellent point-of-use dust collectors that can
be used next to the machine with only a small
amount of ducting. Specifications: 450 CFm, 7.2"
static pressure, 2 cubic foot bag, and 30 micron
filter. motor is 1hp, 110v/220v, 14A/7A.
model g0710
model g1163
figure 56. point-of-use dust collectors.
figure 54. g7315z SHOP FOX® mobile Base.
h7584—Re-Saw fence Retrofit Kit
this retrofit kit allows you to upgrade your existing
aluminum fence for the g0555/g0555p bandsaw
to a cast-iron fence with the 6" high re-saw fence.
Simply unbolt your existing aluminum fence (4
bolts) and bolt on the new cast-iron fence. takes
less than 3 minute to switch over.
T10117—Big Mouth Dust hood with Stand
Capture dust from any machine operation with
this Big mouth dust hood. Simply attach a 4" dust
collection hose and adjust the hood right where
you need it. the free standing base eliminates
complicated machine setups and the tilting 163⁄8
"
x 127⁄8" hood adjusts from 23" to 43" high. every
shop needs one of these!
figure 55. t10117 Big mouth dust hood.
figure 57. h7584 re-Saw Fence retrofit Kit for
the g0555/g0555p Bandsaw.
Order Online at grizzly.com®
-42-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 6: MAINTENANcE
cleaning &
Protecting
ALWAyS disconnect power
to the machine before
performing maintenance.
failure to do this may result
in serious personal injury.
Cleaning the bandsaw is relatively easy. vacuum
away excess wood chips and sawdust, and wipe
off the remaining dust with a dry cloth. if any resin
has built up, use a resin dissolving cleaner to
remove it.
Schedule
protect the unpainted cast iron surfaces on the
table by wiping the table clean after every use—
this ensures moisture from wood dust does not
remain on bare metal surfaces.
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
Keep the table rust-free with regular applications
of products like g96® gun treatment, Slipit®, or
Boeshield® t-9 (contact grizzly to purchase these
products).
Daily
•
•
•
•
Check/correct loose mounting bolts.
Check/correct damaged or worn saw blade.
Check/correct worn or damaged wires.
Correct any other unsafe condition.
Monthly
•
Check for v-belt tension, damage, or wear.
•
remove blade and thoroughly clean all built-
up sawdust from the wheels and rubber tires.
if necessary, re-dress the rubber tires.
Clean/vacuum dust buildup from inside wheel
covers and off the motor.
•
-43-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
Redressing Rubber
Tires
the bearings on this bandsaw are pre-lubricated
and sealed at the factory, and require no lubrica-
tion for the life of the bearings. All bearings are
standard sizes, and replacements can be pur-
chased from our parts department or a bearing
supply store.
As the bandsaw ages, the rubber tires on the
wheels may need to be redressed if they harden or
glaze over. redressing the rubber tires improves
blade tracking and reduces vibration/blade lead.
if the rubber tires become too worn, then blade
tracking will become extremely difficult. At that
point, redressing will no longer be effective and
the rubber tires must be replaced.
As for other items on this machine, such as
adjustment controls, an occasional “shot” of light
oil is just about all that is necessary. Before apply-
ing, however, wipe off any sawdust with a clean
cloth, towel or dry paint brush, then spray on the
lubricant.
To redress the rubber tires:
1. diSConneCt BAndSAW From poWer!
2. put on heavy leather gloves.
3. remove the blade.
ensure that lubricant does not get on the pulleys
or v-belt, which could cause v-belt deterioration
or loss of power transfer due to slippage.
4. Clean any built-up sawdust from the rubber
tires and wheels.
5. hold 100 grit sandpaper against the rub-
ber tire and rotate the wheel by hand. only
redress the rubber enough to expose a fresh
rubber surface.
6. re-install the blade, then make sure the
blade tracking and tension are correct.
-44-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 7: SERvIcE
Review the troubleshooting and procedures in this section if a problem develops with your machine. If you
need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.
Note: Please gather the serial number and manufacture date of your machine before calling.
Troubleshooting
Motor & Electrical
Symptom
possible Cause
possible Solution
machine does
not start or a
breaker trips.
1. power supply is at fault/switched oFF.
1. ensure hot lines have correct voltage on all legs and
main power supply is switched ON.
2. plug/receptacle is at fault or wired incorrectly. 2. test for good contacts; correct the wiring.
3. Wiring is open/has high resistance.
3. Check for broken wires or disconnected/corroded
connections, and repair/replace as necessary.
4. Correct motor wiring connections (Page 56).
5. test/replace.
4. motor connection wired incorrectly.
5. Start capacitor is at fault (110v only).
6. motor on/oFF switch is at fault.
7. Centrifugal switch is at fault.
6. replace faulty on/oFF switch.
7. Adjust/replace centrifugal switch.
machine stalls or 1. incorrect workpiece material.
is underpowered.
1. Use wood with correct moisture content (20% or
less), without glues, and little pitch/resin.
2. decrease feed rate.
2. Feed rate too fast for task.
3. v-belt slipping.
3. tighten/repair/replace (Pages 47 and 48).
4. Correct motor wiring connections (Page 56).
5. test for good contacts; correct the wiring.
6. test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
4. motor connection is wired incorrectly.
5. plug/receptacle is at fault.
6. motor bearings are at fault.
7. motor has overheated.
8. motor is at fault.
7. Clean off motor, let cool, and reduce workload.
8. test/repair/replace.
9. Centrifugal switch is at fault.
9. Adjust/replace centrifugal switch.
machine has
vibration or noisy
operation.
1. motor or component is loose.
1. inspect/replace stripped or damaged bolts/nuts, use
thread locking fluid, and retighten.
2. v-belt worn or loose.
2. tension v-belt (Page 47) or replace v-belt (Page
48).
3. motor fan is rubbing on fan cover.
4. pulley is loose.
3. replace dented fan cover; replace damaged fan.
4. tighten pulley set screw.
5. machine is incorrectly mounted or sits unevenly 5. Adjust stand feet.
on floor.
6. Blade is at fault.
6. replace blade.
7. Cast iron motor mount loose/broken.
8. Centrifugal switch is at fault.
9. motor or spindle bearings are at fault.
7. tighten/replace.
8. Adjust/replace centrifugal switch..
9. test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
-45-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
cutting Operations
Symptom
possible Cause
possible Solution
machine slows
when operating.
1. Feeding workpiece too fast.
2. Blade is dull.
1. reduce feed rate.
2. replace blade (Page 37).
ticking sound
when the saw is
running.
1. Blade weld contacting guide/support bearings 1. Use file or stone to smooth and round the back of the
(a light tick is normal).
blade; slightly loosen the blade guides.
2. Blade weld may be failing.
2. inspect and replace blade if necessary (Page 37).
Blade contacting 1. insert installed upside down or backwards.
1. re-install insert a different way.
2. Align table (Page 29).
table insert.
2. table improperly mounted or aligned.
vibration when
cutting.
1. loose or damaged blade.
2. Sawdust buildup on wheels.
1. tighten or replace blade (Page 37).
2. Clean all sawdust from rubber tires on wheels.
Burn marks on
the edge of the
cut.
1. too much side pressure when feeding 1. Feed workpiece straight into the blade.
workpiece; blade is binding.
2. Blade too wide for size of radius being cut.
2. install a smaller width blade/increase blade tension
(Page 35).
rough or poor
quality cuts.
1. Feeding workpiece too fast.
1. reduce feed rate.
2. Blade guides adjusted incorrectly.
2. re-adjust all blade support and guide bearings
(Pages 25 and 26).
Sawdust buildup 1. Clogged dust port.
1. Clean out dust port.
inside wheel
covers.
2. low CFm (airflow) from dust collection 2. three options:
system.
—Check dust lines for leaks or clogs.
—move dust collector closer to saw.
—install a more powerful dust collector.
Blade wanders
or doesn't cut
straight.
1. Blade lead.
1. refer to Blade lead on Page 52.
2. Sawdust buildup on wheels.
2. Clean all sawdust from rubber tires on wheels.
Cuts are
1. table tilt is not adjusted to 0˚ or positive stop 1. Adjust table tilt to 0˚; readjust positive stop if
not square
(vertically).
has moved out of adjustment.
necessary (Page 28).
2. table tilt scale pointer is not calibrated.
3. table is not square to the blade.
2. Calibrate table tilt scale pointer to 0˚ (Page 28).
3. Shim table (Page 48).
Miscellaneous
Symptom
possible Cause
possible Solution
tensioner
1. Spacer blocks on quick-release tension 1. reset the blade tensioner (Page 53).
mechanism have moved out of adjustment.
mechanism has
poor range of
motion.
Blade tension
scale is grossly
inaccurate.
1. the spring in the blade tension mechanism 1. replace spring in the blade tension mechanism,
has lost its "spring." this is caused by not
releasing the blade tension when not in use or
frequently over-tensioning the bandsaw.
then take better care of the bandsaw by releasing
tension when not in use and not over-tensioning the
blade.
Wheel is noisy.
1. Wheel bearing is worn out.
1. replace the wheel bearing.
2. v-belt is too tight (lower wheel).
2. Check/loosen the belt tension (Page 47).
Blade does
not track
consistently,
correctly, or at
all.
1. Wheels are not coplanar or aligned with each 1. Adjust wheels to be coplanar/aligned with each other
other.
(Page 49).
2. rubber tires on wheels are worn out.
2. redress the rubber tires on the wheels (Page 44);
replace the rubber tires on the wheels.
-46-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Tensioning v-Belt
Tool Needed
hex Wrench 6mm...............................................1
v-Belt Tension
Qty
to ensure optimum power transmission from the
motor to the blade, the v-belt must be in good
condition and operate under proper tension.
To properly tension the v-belt:
1. diSConneCt BAndSAW From poWer!
v-belt tension should be checked at least every
month—more often if the bandsaw is used daily. if
the belt shows signs of cracks, fraying, and exces-
sive wear, replace it as instructed in the Service
section later in this manual.
2. open the lower wheel cover and loosen the
motor adjustment and hinge cap screws
shown in figure 59.
Adjustment
Cap Screw
checking v-Belt Tension
1. diSConneCt BAndSAW From poWer!
2. open the lower wheel cover.
3. the v-belt is properly tensioned if there is
1
approximately ⁄4" deflection of the v-belt
hinge
Cap Screw
when you apply moderate pressure to it
between the pulleys (see the illustration in the
following figure).
—if the v-belt is not properly tensioned,
perform the following Tensioning v-Belt
procedure.
figure 59. locations of the motor adjustment
and hinge cap screws.
3. push the motor to the left (as viewed from the
front of the machine) until there is approxi-
mately 1⁄4" deflection in the v-belt between the
pulley when moderate pressure is applied.
Pulley
1
Approximately ⁄4
"
4. re-tighten both cap screws and close the
wheel cover.
Deflection
Pulley
figure 58. Checking the v-belt tension.
-47-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Unthread the wheel mount bolt clockwise
(left-hand thread), and remove it and the flat
washer from the wheel hub.
Replacing v-Belt
to ensure optimum power transmission from the
motor to the blade, the v-belt must be in good
condition and operate under proper tension.
7. taking care not to misplace the shaft key,
slide the wheel from the shaft.
8. Align the wheel keyway with the shaft key
and slide the wheel back onto the shaft.
if the belt shows signs of cracks, fraying, and
excessive wear, replace it.
9. Secure the wheel with the wheel mount bolt
and flat washer.
Tools Needed
Qty
hex Wrench 6mm...............................................1
Wrench or Socket 13mm....................................1
replacement v-Belt (part no. p0555068) .........1
10. position the v-belt on the desired pulleys,
then properly tension it, as instructed in the
v-Belt Tension subsection on Page 47.
To replace the v-belt:
11. replace the blade, then properly track and
tension it (see Pages 21 and 24).
1. diSConneCt BAndSAW From poWer!
2. put on heavy leather gloves and remove the
blade from the machine.
Shimming Table
3. loosen the motor adjustment and hinge cap
screws shown in figure 60.
to ensure accuracy when cutting stacked cuts or
circles, the table must be 90° to the back of the
blade, as shown in the figure below.
Adjustment
Cap Screw
Wheel mount
hinge
Cap Screw
Bolt
figure 60. locations of the wheel mount bolt,
and motor adjustment and hinge cap screws.
figure 61. Checking the table to be
perpendicular to the back of the blade.
4. move the motor to the right (as viewed from
the front of the bandsaw) so that the adjust-
ment cap screw slides to the right in the
slot—this will release the v-belt tension.
if the table is not perpendicular to the back of the
blade, correct this condition by placing shim stock
between the table and trunnions underneath it.
5. roll the v-belt off the pulleys.
Tip: For fine adjustments, use electrical washers
on the bolts that secure the table.
-48-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheel Alignment
Parallel, Not
Coplanar
Coplanar
Wheel alignment is one of the most critical fac-
tors for optimal performance from your bandsaw.
Wheels are properly aligned when they are par-
allel with each other and in the same plane or
“coplanar” (see the illustration in the figure to the
right).
heat, vibration, wandering, blade wear, tire wear
and overall bandsaw wear are considerably
decreased when the wheels are parallel and
coplanar. Additionally, wheels that are parallel and
coplanar automatically track the blade by balanc-
ing it on the crown of the wheel—this is known as
“coplanar tracking.”
Straightedge
Shim
Wheel
Contacts Top
And Bottom of
Both Wheels
Bringing the wheel into alignment may require
a combination of shimming a wheel and center/
lateral tracking the upper blade.
Tools Needed
Qty
Straightedge 4 ft.................................................1
Fine ruler...........................................................1
Wrench or Socket 13mm....................................1
Wrench or Socket 19mm....................................1
Not Parallel
Not Coplanar
Not Parallel
Not Coplanar
checking Wheel Alignment
1. diSConneCt BAndSAW From poWer!
2. remove the table.
Adjust
Tracking
3. With the blade on and properly tensioned,
hold a straightedge close to the center of
both wheels. make sure the straightedge fully
extends across the rims of both wheels, as
shown in the figure below.
figure 63. Wheel alignment illustration.
figure 62. Checking if the wheels are coplanar.
model g0555/g0555p (mfg. Since 5/11)
-49-
Download from Www.Somanuals.com. All Manuals Search And Download.
—if the wheels are parallel and coplanar, the
straightedge will touch the top and bottom
rims on both wheels. no further adjustment
is required.
3. With the straightedge touching both rims of
the wheel that does not need to be adjusted,
measure the distance away from the other
wheel with a fine ruler, as shown in the figure
below. the distance measured with the ruler
is the distance this wheel must be shimmed.
—if the wheels are parallel but not coplanar,
the straightedge will touch the top and bot-
tom rims on one wheel, but will not touch
either rim on the other wheel. in this case,
shim the wheel that does not touch the
straightedge, as instructed in the following
Shimming a Wheel procedure.
—if the wheels are not coplanar, the straight-
edge will touch both rims of one wheel, but
at an angle to the other wheel. in this case,
you will need to adjust the tracking of the
upper wheel.
if the upper wheel is tilted from top to
bottom only, perform the center Blade
Tracking procedure as instructed earlier in
this manual.
figure 64. measuring the distance to shim the
wheel to be coplanar.
if the upper wheel is tilted from side to side,
perform Upper Wheel Lateral Adjustment
procedure that follows.
4. remove the wheel to be shimmed, then
place shimming washers in the amount mea-
sured in Step 3 onto the wheel shaft.
5. re-install the wheel and secure it in place.
Shimming a Wheel
A wheel that is parallel with the other wheel, but
is not coplanar, must be shimmed by the distance
that it is not in the same plane with the other
wheel.
6. re-install the blade, then properly tension it
for operation.
Note: Often the wheels may be coplanar with
the blade loose, then be pulled out of align-
ment when it is tightened.
To shim a wheel:
1. diSConneCt BAndSAW From poWer!
7. perform the previous checking Wheel
Alignment procedure. if necessary to make
the wheels parallel, repeat this procedure.
2. Adjust the upper wheel tracking so that it is
parallel with the bottom wheel.
8. When you are satisfied with the adjustment,
re-install the blade and close the wheel cov-
ers.
-50-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools Needed
hex Wrench 2.5mm............................................1
Wrench or Socket 19mm....................................1
Qty
Upper Wheel Lateral Adjustment
if the upper wheel is tilted laterally (side to side),
perform the following procedure to make it copla-
nar with the lower wheel.
To adjust the upper wheel laterally:
there are two set screws in the upper wheel
bracket, shown in figures 65–66, that adjust the
wheel tilt from side to side.
1. diSConneCt BAndSAW From poWer!
2. remove the blade from the machine.
3. remove the hex nut that secures the upper
wheel, then slide the wheel from the shaft.
Front Adjustment
Set Screw
4. thread one set screw out and thread the
other set screw in the same amount to tilt the
wheel laterally.
For instance, to tilt the right side of the upper
wheel back, thread the rear set screw out
and thread the front set screw in the same
amount.
5. Slide the upper wheel back on the shaft,
then repeat the checking Wheel Alignment
procedure and, if necessary, repeat this pro-
cedure until the upper wheel is coplanar with
the lower wheel.
figure 65. Front lateral adjustment set screw
(viewed with the upper wheel removed).
rear Adjustment
Set Screw
figure 66. rear lateral adjustment set screw.
-51-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
To skew your fence:
1. Cut a piece of scrap wood approximately ⁄4
Blade Lead
3
"
thick x 3" wide x 17" long. on the wide face of
the board, draw a straight line parallel to the
long edge.
Bandsaw blades may wander off the cut line
when sawing, as shown in the figure below. this
is called blade lead.
2. Slide the bandsaw fence out of the way and
cut halfway through the board on the line by
pushing it into the blade. turn the bandsaw
OFF and wait for the blade to stop. do not
move the board.
Blade lead is usually caused by too fast of a
feed rate, a dull or abused blade, or improper
blade tension. if your blade is sharp/undamaged,
properly tensioned, and you still have blade lead,
perform the following procedures.
3. Clamp the board to the bandsaw table, then
slide the fence over to the board so it barely
touches one end of the board.
4. Use a 4mm hex wrench to loosen the four
fence adjustment cap screws on top of the
fence, skew the fence so that it is parallel
with the scrap piece, then re-tighten the cap
screws.
5. make a few cuts using the fence.
—if blade lead is still present, repeat Steps
1–4 until the blade and fence are parallel
with each other.
figure 67. example of blade lead.
To correct blade lead:
—or, shift the table, as instructed in the fol-
lowing procedure.
1. make sure the blade is properly tensioned
and the blade guides are adjusted correctly.
To shift the table:
1. on a scrap piece of wood, mark a line that is
perpendicular to the front edge.
2. Use lesspressure when feeding the workpiece
through the cut—this will reduce the feed
rate.
2. Cut halfway through the board on the line by
pushing it into the blade.
3. make sure the miter slot and fence are paral-
lel to the blade line (see the Aligning Table
and Aligning fence procedures in this man-
ual for detailed information).
3. turn the bandsaw OFF and wait for the blade
to stop.
4. disconnect the bandsaw from power, then
use a 10mm wrench to loosen the six hex
bolts underneath the table that secure it to
the trunnion brackets.
4. if after Steps 1–3 there is still blade lead
present, compensate for this condition by
skewing the fence or shifting the table, as
instructed in the following procedures.
5. Shift the table to compensate for the blade
lead, re-tighten the hex bolts, then re-connect
the bandsaw to power.
6. repeat Steps 1–5 until there is no longer any
blade lead.
-52-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. rotate the spacers fully away from the cross-
bar, then rotate the blade tension knob so
that the red marker is at the blade width mark
for the installed blade.
Blade Tensioner
the blade tensioner may need to be reset for one
of the following reasons:
4. pull the quick release lever down to the hori-
zontal position.
•
the blade tension quick release lever will not
move down into the horizontal position when
the tension scale is correctly adjusted for the
installed blade.
5. pull up on the tension knob to apply as much
tension on the blade as possible.
6. While maintaining the upward pressure on
the tension knob, thread the upper spacer
down until it touches the crossbar, then re-
tighten the set screw to secure it in place.
•
you have installed a blade of a different
length.
Tool Needed
Qty
hex Wrench 2.5mm............................................1
7. thread the lower spacer down until it touches
the top of the tensioner casting, then thread
it back up 1–2 turns to leave a small space
above the casting and re-tighten the set
screw to secure the setting.
To reset the blade tensioner:
1. diSConneCt BAndSAW From poWer!
2. move the blade tension lever up to the verti-
cal position to release blade tension, then
loosen the set screws on both spacers shown
in figure 68.
8. move the quick release lever up to the vertical
position and make sure there is no tension on
the blade. if all the tension is not released,
the lower spacer needs to be threaded farther
down the shaft toward the tensioner casting.
Crossbar
Upper
Spacer
tensioner
Casting
lower
Spacer
figure 68. locations of spacers and tensioner
crossbar.
-53-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. if the reading on the scale is not the same
as the width of the cut workpiece, loosen the
two screws on the magnifying window (see
figure 69) and adjust it to match the width of
the cut workpiece.
fence Scale
calibration
you may need to recalibrate the fence scale after
changing or adjusting the blade, or if the scale
is not producing accurate cuts. recalibrate the
fence scale by adjusting the hairline indicator on
the fence and testing your adjustment by cutting a
piece of scrap wood.
Screws
Tools Needed
Qty
phillips Screwdriver #1 .......................................1
To calibrate the scale:
1. Set the fence anywhere along the scale and
locate a piece of scrap wood with at least one
straight edge.
figure 69. Fence scale window and screws.
5. re-tighten the screws—the scale is now cor-
rectly calibrated.
Note: Joint the edge with a jointer if needed
to make the edge straight.
2. hold the straight edge of the workpiece firmly
against the fence, and feed the workpiece
through the saw blade with a push stick.
3. measure the width of the cut workpiece. the
width of the workpiece should match the
reading on the fence scale.
-54-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
machine
SEcTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-
es to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is con- WIRE/COMPONENT DAMAGE. Damaged wires
nected to a power source is extremely dangerous. or components increase the risk of serious per-
Touching electrified parts will result in personal sonal injury, fire, or machine damage. If you notice
injury including but not limited to severe burns, that any wires or components are damaged while
electrocution, or death. Disconnect the power performing a wiring task, replace those wires or
from the machine before servicing electrical com- components.
ponents!
MOTOR WIRING. The motor wiring shown in
MODIFICATIONS. Modifying the wiring beyond these diagrams is current at the time of printing
what is shown in the diagram may lead to unpre- but may not match your machine. If you find this
dictable results, including serious injury or fire. to be the case, use the wiring diagram inside the
This includes the installation of unapproved after- motor junction box.
market parts.
CAPACITORS/INVERTERS. Some capacitors
WIRE CONNECTIONS. All connections must and power inverters store an electrical charge for
be tight to prevent wires from loosening during up to 10 minutes after being disconnected from
machine operation. Double-check all wires dis- the power source. To reduce the risk of being
connected or connected during any wiring task to shocked, wait at least this long before working on
ensure tight connections.
capacitors.
CIRCUIT REQUIREMENTS. You MUST follow EXPERIENCING DIFFICULTIES. If you are expe-
the requirements at the beginning of this man- riencing difficulties understanding the information
ual when connecting your machine to a power included in this section, contact our Technical
source.
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
-55-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
Start/Stop Switch
O N
B1 A1
B2 A2
B3 A3
O F F
Ground
figure 70. motor and on/oFF switch locations.
Neutral
Hot
Ground
Hot
G
110 VAC
220
VAC
5-15 Plug
(Pre-wired)
Ground
220 VAC
Hot
6-15 Plug
Rewired for 220V
(As Recommended)
Motor
Pre-wired
for 110V
Motor
Rewired
for 220V
Start Capacitor
200MFD 250VAC
Run Capacitor
20MFD 250VAC
Start Capacitor
200MFD 250VAC
Run Capacitor
20MFD 250VAC
2
3
3
1
4
2
1
4
Ground
Ground
Rewired for 220V
READ ELECTRICAL SAFETY
ON PAGE 55!
-56-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 9: PARTS
Main
-57-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Parts List
REF
PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
P0555001
P0555P001
PB80M
BASE (G555)
45
46
47
48
48
49
50
51
55
56
57
58
59
59
P0555045
P0555009
PB81M
LOWER WHEEL ASSY W/TIRE
SHAFT WASHER 30 X 8 X 3MM
HEX BOLT M8-1.25 X 20 LH
1
BASE (G0555P)
2
HEX BOLT M16-2 X 55
FLAT WASHER 16MM
HEX NUT M16-2
3
PW08M
P0555048
LOWER WHEEL COVER (G0555)
4
PN13M
P0555P048 LOWER WHEEL COVER (G0555P)
P0555049 KNOB M8-1.25
PTLW03M INT TOOTH WASHER 8MM
5
P0555005
P0555006
P6204LLU
PK23M
ALIGNMENT PIN
6
LOWER WHEEL SHAFT
BALL BEARING 6204 LLU
KEY 5 X 5 X 25
7
P0555051
PS08M
DOOR LATCH STUD M8-1.25 X 14
PHLP HD SCR M5-.8 X 12
CATCH
8
9
P0555009
PS16M
SHAFT WASHER 30 X 8 X 3MM
PHLP HD SCR M8-1.25 X 16
MOTOR 1HP 110/220V 60HZ V2.05.11
P0555056
P0555057
10
11V2
ALIGNMENT BOLT M5-.8 X 27
P0555011V2
PHTEK4M TAP SCREW M4 X 8
11V2-1 P0555011V2-1 MOTOR FAN
P0555059
FRONT UPPER WHEEL COVER (G0555)
11V2-2 P0555011V2-2 MOTOR FAN COVER
11V2-3 P0555011V2-3 S CAPACITOR COVER
11V2-4 P0555011V2-4 S CAPACITOR 200M 250V
11V2-5 P0555011V2-5 JUNCTION BOX
11V2-6 P0555011V2-6 CENTRIFUGAL SWITCH
11V2-7 P0555011V2-7 CONTACT PLATE
P0555P059 FRONT UPPER WHEEL COVER (G0555P)
61A P0555061A REAR UPPER WHEEL COVER V2.07.07 (G0555)
P0555P061 REAR UPPER WHEEL COVER (G0555P)
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
79
80
81
82
83
84
85
86
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
PFS01M
P0555063
P0555064
P0555065
PW05M
FLANGE SCREW M5-.8 X 8
UPPER WHEEL COVER HINGE
WHEEL COVER STANDOFF
LEFT BLADE GUARD
11V2-8 P6202ZZ
11V2-9 P6205ZZ
BALL BEARING 6202ZZ
BALL BEARING 6205ZZ
FLAT WASHER 4MM
11V2-10 P0555011V2-10 R CAPACITOR COVER
11V2-11 P0555011V2-11 R CAPACITOR 20M 250V
PHTEK2M TAP SCREW M3.5 X 16
P0555068
P0555069
PFH07M
PB20M
RIBBED V-BELT 200J5
LOWER WHEEL COVER HINGE
FLAT HD SCR M5-.8 X 10
HEX BOLT M8-1.25 X 35
FLAT WASHER 8MM
12
P0555012
PSS04M
MOTOR PULLEY
13
SET SCREW M6-1 X 12
ON/OFF SWITCH 110/220V V2.05.11
TAP SCREW M3.5 X 12
FLAT WASHER 4MM
14V2
15
P0555014V2
PHTEK1M
PW05M
PW01M
16
PLW04M
PN03M
LOCK WASHER 8MM
HEX NUT M8-1.25
17
PS40M
PHLP HD SCR M5-.8 X 16
TENSION INDICATOR
18
P0555018
PTLW02M
P0555020
P0555021
PS19M
P0555075
PS08M
CORD CLAMP
19
EXT TOOTH WASHER 5MM
SWITCH BOX
PHLP HD SCR M5-.8 X 12
GUIDE POST BRACKET
THUMB SCREW M6-1 X 16
GUIDE SPACING SLEEVE
BALL BEARING 6000ZZ
FLANGE SCREW M6-1 X 8
GUIDE POST
20
P0555079
PTS001M
P0555081
P6000ZZ
PFS06M
P0555084
PLW01M
21
SWITCH BOX MOUNT
23
PHLP HD SCR M5-.8 X 6
STRAIN RELIEF
24
P0555024
P0555025
P0555026
P0555027
P0555028
P0555P028
P0555029
P0555030A
PSS31M
25
POWER CORD 16G 3C 6FT 5-15
MOTOR CORD
26
27
STRAIN RELIEF
LOCK WASHER 5MM
28
UPPER FRAME ARM (G0555)
UPPER FRAME ARM (G0555P)
KNOB BOLT M10-1.5 X 30
UPPER WHEEL SLIDING BRACKET V2.07.07
SET SCREW M5-.8 X 8
WING NUT M8-1.25
PCAP78M CAP SCREW M5-.8 X 40
28
P0555088
P0555089
P0555090
PW03M
LOWER RIGHT BLADE GUARD
UPPER GUIDE BRACKET
UPPER RIGHT BLADE GUARD
FLAT WASHER 6MM
29
30A
30A-1
31
PWN02M
P0555032
P0555033A
P0555034
P0555035
P0555035-1
PRP14M
PB05M
HEX BOLT M6-1 X 8
32
KNOB BOLT M8-1.25 X 45
BLADE ADJ SCR ASSY 7" THREAD
DOWEL PIN
P0555093
PW03M
LOWER GUIDE BRACKET
FLAT WASHER 6MM
33A
34
PB08M
HEX BOLT M6-1 X 20
35
UPPER WHEEL SHAFT HINGE ASSY
UPPER WHEEL SHAFT
ROLL PIN 3 X 6
PCAP33M CAP SCREW M5-.8 X 12
35-1
35-2
35-3
38
P0555097
P0555098
PRP15M
P0555100
P0555101
P0555102
P0555103
PB02M
TABLE
TABLE INSERT
ROLL PIN 3 X 8
TABLE PIN
P0555035-3
P0555038
PSN04M
UPPER WHEEL SHAFT HINGE
COMPRESSION SPRING 3.8 X 13.5 X 81
SQUARE NUT M10-1.5
UPPER WHEEL
39
TRUNNION
40
P0555040
T23070
SCALE
41
WHEEL TIRE 14"
TRUNNION CLAMP SHOE
HEX BOLT M6-1 X 12
TRUNNION SUPPORT BRACKET
42
PN24M
HEX NUT M12-1.25
43
PR21M
INT RETAINING RING 35MM
BALL BEARING 6202 LLU
P0555105
44
P6202LLU
-58-
Model G0555/G0555P (Mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
106
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
PB26M
HEX BOLT M8-1.25 X 30
POINTER
129
P0555129
ECCENTRIC SHAFT
SET SCREW M5-.8 X 8
SET SCREW M5-.8 X 5
UPPER LOCK COLLAR
LOWER LOCK COLLAR
FLAT WASHER 10MM
QUICK RELEASE LEVER
FLAT WASHER 8MM
BUSHING
P0555108
PFS03M
P0555110
PB73M
130A PSS31M
130B PSS07M
131A P0555131A
131B P0555131B
FLANGE SCREW M5-.8 X 6
KNOB M10-1.5
HEX BOLT M10-1.5 X 50
HEX BOLT M8-1.25 X 80
HEX NUT M8-1.25
PB82M
132
133
134
135
136
137
138
139
140
141
142
143
151
152
153
154
PW04M
PN03M
P0555133
PW01M
P0555114
PCAP31M
PLW04M
PW01M
MITER GAUGE ASSEMBLY
CAP SCREW M8-1.25 X 25
LOCK WASHER 8MM
FLAT WASHER 8MM
STEEL BALL
P0555135
PCAP01M
P0555137
PB15M
CAP SCREW M6-1 X 16
SPACER
P0555118
P0555119
PSS30M
PSS98M
P0555122
PB08M
HEX BOLT M8-1.25 X 40
LOCK NUT M8-1.25
SUPPORT PLATE
COMPRESSION SPRING 1.5 X 5 X 9
SET SCREW M10-1.5 X 10
SET SCREW M8-1 X 35
MICRO ADJUSTING NUT 1.65
HEX BOLT M6-1 X 20
CORD CLAMP
PLN04M
P0555140
P0555141
PLW04M
PB09M
PIVOT ARM
LOCK WASHER 8MM
HEX BOLT M8-1.25 X 20
FLAT WASHER 8MM
PHLP HD SCR M5-.8 X 12
EXT TOOTH WASHER 5MM
SPACER 8MM
P0555124
PS08M
PW01M
PHLP HD SCR M5-.8 X 12
LOCK NUT M4-.7
PS08M
PLN01M
PW02M
PTLW02M
P0555154
FLAT WASHER 5MM
BALL BEARING 608ZZ
P608ZZ
-59-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Stand
205
206
207
204
208
202
201
211
212
212
211
213
209
210
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201
201
202
204
205
205
206
207
P0555201
P0555P201
PCB06M
PFN01M
P0555205
P0555P205
PB83M
STAND TOP (G0555)
STAND TOP (G0555P)
208
209
209
210
210
211
212
213
PFN02M
P0555209
P0555P209
P0555210
P0555P210
PN08
FLANGE NUT M6-1
UPPER STAND BRACE (G0555)
UPPER STAND BRACE (G0555P)
LOWER STAND BRACE (G0555)
LOWER STAND BRACE (G0555P)
HEX NUT 3/8-16
CARRIAGE BOLT M8-1.25 X 16
FLANGE NUT M8-1.25
STAND SIDE (G0555)
STAND SIDE (G0555P)
HEX BOLT M6-1 X 16
FLAT WASHER 6MM
PW04M
FLAT WASHER 10MM
PW03M
P0555213
STAND FOOT
-60-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
fence
303
318
316
312
320
307
323
308
304
309
311
322
302
313
315
322
310
305
326
300
327
325
323
306
320
317
321
324
314
319
301
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
300
301
302
303
304
305
306
307
308
309
310
311
312
313
P0555300
FENCE KIT ASSEMBLY W/RAILS
FRONT FENCE RAIL
FENCE BASE
314
315
316
317
318
319
320
321
322
323
324
325
326
327
P0555314
PN01M
REAR FENCE RAIL
HEX NUT M6-1
P0555301
P0555302
P0555303
P0555304
P0555305
P0555306
P0555307
P0555308
P0555309
P0555310
P0555311
PCAP198M
P0555313
PFS04M
P0555317
P0555318
P0555319
PHTEK3M
P0555321
PN01M
FLANGE SCREW M4-.7 X 6
FRONT RAIL END CAP
FENCE END CAP
FENCE MOUNT ROD
LOCK SHAFT
SPRING PLATE
SPACER PLATE
FENCE
REAR RAIL END CAP
TAP SCREW M3.5 X 8
SCALE
SLEEVE
HEX NUT M6-1
LOCK HANDLE
PLW03M
PCAP01M
PB08M
LOCK WASHER 6MM
CAP SCREW M6-1 X 16
HEX BOLT M6-1 X 20
FLANGE SCREW M4-.7 X 8
FLAT WASHER 6MM
FENCE STAND-OFF
SCALE WINDOW
CAP SCREW M6-1 X 60
LOCK CAM
PFS17M
PW03M
-61-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Labels
146
216
144V2
145
144V2
155
148
145
155
148
148
147
157
148
147
149
156
218
217
214
REF PART #
DESCRIPTION
MACHINE ID LABEL V2.05.11 (G0555)
REF PART #
DESCRIPTION
144V2 P0555144V2
155
156
157
214
216
217
218
G9987
GRIZZLY NAMEPLATE
144V2 P0555P144V2 MACHINE ID LABEL V2.05.11 (G0555P)
PPAINT-1
GRIZZLY GREEN TOUCH-UP PAINT
GRIZZLY PUTTY TOUCH-UP PAINT
GRIZZLY.COM LABEL
145
146
147
148
149
PLABEL-11
P0555146
SAFETY GLASSES LABEL
MODEL NUMBER LABEL (G0555)
UNPLUG BANDSAW LABEL
BANDSAW DOOR LABEL
ELECTRICITY LABEL
PPAINT-11
P0555P213
P0555P216
PLABEL-75
PPAINT-24
PLABEL-18
PLABEL-23
PLABEL-14
MODEL NUMBER LABEL (G0555P)
POLAR BEAR LOGO
POLAR BEAR WHITE TOUCH-UP PAINT
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
-62-
model g0555/g0555p (mfg. Since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email ________________________ Invoice #_________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Woodwork
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Shotgun News
____ Today’s Homeowner
____ Wood
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
____ 6-9
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTy AND RETURNS
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
Download from Www.Somanuals.com. All Manuals Search And Download.
|