MODEL G0756
INDUSTRIAL DRILL PRESS
OWNER'S MANUAL
(For models manufactured since 03/13)
Copyright © MAy, 2013 By grizzly industriAl, inC.,
WARNING: NO PORTION Of ThIS MANUAL MAy bE REPRODUcED IN ANy ShAPE
OR fORM WIThOUT ThE WRITTEN APPROvAL Of GRIzzLy INDUSTRIAL, INc.
#dM15670 printed in ChinA
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
INTRODUcTION............................................... 2
SEcTION 6: MAINTENANcE......................... 32
schedule...................................................... 32
ongoing ............................................................32
daily, After operations......................................32
Annually ............................................................32
Cleaning and protecting .............................. 32
lubrication ................................................... 33
headstock lubrication ......................................33
Ball oilers..........................................................34
Changing Coolant ........................................ 34
Machine description ...................................... 2
Contact info.................................................... 2
Manual Accuracy ........................................... 2
identification................................................... 3
Control panel ................................................. 4
Machine data sheet ...................................... 5
SEcTION 1: SAfETy....................................... 7
safety instructions for Machinery .................. 7
safety for drill presses .................................. 9
SEcTION 7: SERvIcE ................................... 35
troubleshooting ........................................... 35
Motor & electrical..............................................35
drill press operations.......................................36
replacing lamp Bulb................................... 37
torque limiter.............................................. 37
SEcTION 2: POWER SUPPLy...................... 10
Availability.........................................................10
Full-load Current rating ..................................10
Circuit requirements for 220V..........................10
grounding instructions......................................11
extension Cords................................................11
SEcTION 8: WIRING...................................... 38
Wiring safety instructions............................ 38
Wiring overview........................................... 39
Component location index.......................... 39
power Connection Wiring ............................ 40
electric Clutch Wiring................................... 40
Motor & pump Wiring ................................. 41
Control panel ............................................... 42
Control panel & limit switches ................... 43
electrical panel Wiring................................. 44
electrical Wiring panel photo ...................... 45
SEcTION 3: SETUP ....................................... 12
unpacking.................................................... 12
needed for setup......................................... 12
inventory ...................................................... 12
Cleanup........................................................ 13
site Considerations...................................... 14
lifting & placing........................................... 15
Anchoring to Floor ....................................... 15
Anchoring to Concrete Floors...........................15
Arbor/Chuck Assembly ................................ 16
initial lubrication.......................................... 16
power Connection........................................ 17
test run ...................................................... 18
Coolant system............................................ 20
spindle Break-in .......................................... 21
SEcTION 9: PARTS....................................... 46
table support & Coolant Breakdown .......... 46
gearbox Breakdown .................................... 48
gearbox Breakdown 2................................. 49
spindle Feed Breakdown............................. 51
headstock Breakdown................................. 53
headstock Breakdown 2.............................. 54
electrical parts Breakdown.......................... 56
labels & Cosmetics..................................... 58
SEcTION 4: OPERATIONS ........................... 22
operations overview ................................... 22
tooling installation & removal .................... 22
installing tapered tooling ................................23
removing tooling with Automatic drift.............23
removing tooling Manually .............................23
depth stop................................................... 24
table positioning ......................................... 24
raising/lowering table ....................................24
rotating table...................................................24
selecting spindle rpM................................ 25
drilling Mode................................................ 26
Automatic power downfeed ........................ 27
tapping Mode.............................................. 28
Coolant system............................................ 28
WARRANTy & RETURNS ............................. 61
SEcTION 5: AccESSORIES......................... 29
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUcTION
Machine Description
Manual Accuracy
We are proud to provide a high-quality owner’s
manual with your new machine!
We are proud to offer the Model g0756 18-speed
heavy-duty drill press. When used according to
the guidelines set forth in this manual, you can
expect years of trouble-free, enjoyable operation
and proof of grizzly’s commitment to customer
satisfaction.
We made every effort to be exact with the instruc-
tions, specifications, drawings, and photographs
contained inside. sometimes we make mistakes,
but our policy of continuous improvement also
means that sometimes the machine you receive
will be slightly different than what is shown in
the manual.
this drill press features power tapping with an
electronic clutch and activation buttons on the
downfeed handles. spindle speed is adjustable
through the use of the levers above the main
control panel. the pump-controlled coolant sys-
tem helps provide optimum working results and
extended longevity of tooling.
if you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure, check our website
for an updated version. We post current manuals
and manual updates for free on our website at
contact Info
Alternatively, you can call our technical support
for help. Before calling, please write down the
Manufacture Date and Serial Number stamped
into the machine id label (see below). this infor-
mation helps us determine if updated documenta-
tion is available for your machine.
We stand behind our machines. if you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. this will help us help you faster.
grizzly technical support
1203 lycoming Mall Circle
Muncy, pA 17756
phone: (570) 546-9663
email: techsupport@grizzly.com
Manufacture date
serial number
We want your feedback on this manual. What did
you like about it? Where could it be improved?
please take a few minutes to give us feedback.
grizzly documentation Manager
p.o. Box 2069
Bellingham, WA 98227-2069
email: manuals@grizzly.com
-2-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
C
K
l
B
d
e
A
M
F
J
n
i
h
g
A. Main power switch
b. lifting eye Bolt
c. Motor
h. Automatic drift
I. Automatic downfeed Adjustment Knob
J. Coolant nozzle
D. speed Control levers
E. Control panel (see Page 4 for details)
f. Chip guard
K. oil site glass
L. Coarse downfeed handles
M. table lock handles
G. Coolant pump
N. table height Adjustment Crank
-3-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
control Panel
A
B
F
C
g
h
d
i
e
figure 1. Control panel
A. Spindle Speed Levers: used to get spindle
speed at available rpMs.
f. Working Lamp Switch: turns work light on
or off.
b. coolant Pump Switch: turns pump on,
sending coolant to nozzle
G. EMERGENcy STOP button: immediately
cuts power to motor and control panel when
pressed. remains depressed until button is
reset by twisting clockwise.
c. high/Low Spindle Speed Range Switch:
selects high/low range for spindle speed.
h. Drilling/Tapping Switch: selects between
drilling and tapping modes.
D. Spindle Rotation Switch: Controls direction.
E. Spindle Stop button: stops all work.
I. Spindle Start button: starts machine when
Master power switch has already been
turned to the on position and the high/low
spindle speed range switch is turned to 1 or
2.
-4-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Data Sheet
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0756 HEAVY-DUTY DRILLING MACHINE
Product Dimensions:
Weight............................................................................................................................................................ 1026 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 22 x 37 x 89-1/2 in.
Footprint (Length x Width)............................................................................................................................ 29 x 20 in.
Shipping Dimensions:
Type.......................................................................................................................................................... Wood Crate
Content........................................................................................................................................................... Machine
Weight............................................................................................................................................................ 1202 lbs.
Length x Width x Height....................................................................................................................... 90 x 28 x 45 in.
Must Ship Upright.................................................................................................................................................... No
Electrical:
Power Requirement................................................................................................................... 220V, 3-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 220V
Full-Load Current Rating....................................................................................................................................... 6.6A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included............................................................................................................................................... No
Recommended Power Cord............................................................................... “S”-Type, 4-Wire, 14 AWG, 300 VAC
Plug Included........................................................................................................................................................... No
Recommended Plug Type................................................................................................................................... 15-15
Switch Type.................................................................................................... Magnetic Switch w/Overload Protection
Recommended Phase Converter....................................................................................................................... G5844
Motors:
Coolant Pump
Type..................................................................................................................................................... Universal
Horsepower................................................................................................................................................. 60W
Phase.................................................................................................................................................... 3-Phase
Amps........................................................................................................................................................... 0.2A
Speed................................................................................................................................................ 1725 RPM
Power Transfer ............................................................................................................................... Direct Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
Main
Type........................................................................................................................................... TEFC Induction
Horsepower............................................................................................................................... 1-1/8 HP / 2 HP
Phase.................................................................................................................................................... 3-Phase
Amps........................................................................................................................................................... 6.4A
Speed....................................................................................................................................... 875 / 1725 RPM
Power Transfer ................................................................................................................................. Gear Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
-5-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications:
Operation Info
Spindle Travel.............................................................................................................................................. 7 in.
Max Distance Spindle to Column........................................................................................................ 13-3/4 in.
Max Distance Spindle to Table............................................................................................................ 30-3/4 in.
Vertical Table Travel (Z-Axis).................................................................................................................... 20 in.
Table Swivel (Left/Right)...................................................................................................................... 360 deg.
Drilling Capacity for Cast Iron................................................................................................................ 1-1/2 in.
Drilling Capacity for Steel.................................................................................................................... 1-3/16 in.
Table Info
Table Length.............................................................................................................................................. 22 in.
Table Width................................................................................................................................................ 22 in.
Table Thickness.................................................................................................................................... 1-7/8 in.
Number of T-Slots............................................................................................................................................ 2
T-Slot Size.............................................................................................................................................. 9/16 in.
X/Y-Axis Travel per Handwheel Revolution.......................................................................................... 0.200 in.
Z-Axis Travel per Handwheel Revolution............................................................................................. 0.100 in.
Spindle Info
Spindle Taper............................................................................................................................................ MT#4
Number of Vertical Spindle Speeds................................................................................................................ 18
Range of Vertical Spindle Speeds............................................................................................. 60 – 1740 RPM
Quill Diameter.............................................................................................................................................. 3 in.
Quill Feed Rates................................................................................................................. 0.004, 0.008 in./rev.
Spindle Bearings......................................................................................................... Tapered Roller Bearings
Construction
Spindle Housing/Quill........................................................................................................................... Cast Iron
Table....................................................................................................................... Precision-Ground Cast Iron
Head.................................................................................................................................................... Cast Iron
Column/Base.......................................................................................................... Precision-Ground Cast Iron
Base..................................................................................................................................................... Cast Iron
Paint....................................................................................................................................................... Enamel
Other Specifications:
Country Of Origin ............................................................................................................................................... China
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
ISO 9001 Factory .................................................................................................................................................. Yes
CSA Certified .......................................................................................................................................................... No
Features:
7" Spindle Travel
Recycling Coolant System
Power Tapping w/Electronic Clutch
2-Speed Power Downfeed
Oil-Bath Gearhead w/Circulating Pump
MT#4 Spindle w/Tool Quick-Removal Feature
Spindle Speeds Controlled by Gearhead Levers
Tapping Activation Buttons on Downfeed Handles
Precision-Ground Table Base
Spindle Safety Shield
Halogen Work Light
Precision-Ground Cast Iron Base Table, 21" x 19-3/4", w/Two 11/16" T-Slots
-6-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 1: SAfETy
for your Own Safety, Read Instruction
Manual before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
cOULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAy result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
OWNER’S MANUAL. read and understand this ELEcTRIcAL EQUIPMENT INJURy RISKS. you
owner’s manual BeFore using machine.
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. to reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
TRAINED OPERATORS ONLy. untrained oper-
ators have a higher risk of being hurt or killed.
only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
DIScONNEcT POWER fIRST. Always discon-
nect machine from power supply BeFore making
adjustments, changing tooling, or servicing machine.
this prevents an injury risk from unintended startup
or contact with live electrical components.
DANGEROUS ENvIRONMENTS. do not use
machinery in areas that are wet, cluttered, or have
poor lighting. operating machinery in these areas
greatly increases the risk of accidents and injury.
EyE PROTEcTION. Always wear Ansi-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. everyday
eyeglasses are not approved safety glasses.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-7-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
WEARING PROPER APPAREL. do not wear fORcING MAchINERy. do not force machine.
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work-
piece control.
it will do the job safer and better at the rate for
which it was designed.
NEvER STAND ON MAchINE. serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
hAzARDOUS DUST. dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a niosh-approved respirator to
reduce your risk.
STAbLE MAchINE. unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE REcOMMENDED AccESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. using improper acces-
sories will increase the risk of serious injury.
hEARING PROTEcTION. Always wear hear-
ing protection when operating or observing loud
machinery. extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
UNATTENDED OPERATION. to reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. never leave machine running
while unattended.
REMOvE ADJUSTING TOOLS. tools left on
machinery can become dangerous projectiles
upon startup. never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
MAINTAIN WITh cARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
USE cORREcT TOOL fOR ThE JOb. only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. never make unapproved modifica-
tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
chEcK DAMAGED PARTS. regularly inspect
machine for any condition that may affect safe
operation. immediately repair or replace damaged
or mis-adjusted parts before operating machine.
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
MAINTAIN POWER cORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—not the cord. pulling the cord
may damage the wires inside. do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
chILDREN & bySTANDERS. Keep children and
bystanders at a safe distance from the work area.
stop using machine if they become a distraction.
EXPERIENcING DIffIcULTIES. if at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
technical support at (570) 546-9663.
GUARDS & cOvERS. guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.
-8-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety for Drill Presses
EyE/fAcE/hAND PROTEcTION. A face shield
used with safety glasses is recommended. Always
keep hands and fingers away from the drill bit.
never hold a workpiece by hand while drilling! do
not wear gloves when operating the drill.
DRILL OPERATION. never start the drill press
with the drill bit pressed against the workpiece.
Feed the drill bit evenly into the workpiece. Back
the bit out frequently to clear deep holes.
cLEARING chIPS. turn the machine OFF and
clear chips and scrap pieces with a brush.
disconnect power, remove drill bit, and clean
table before leaving the machine.
SEcURING bIT. properly tighten and securely
lock the drill bit in the chuck.
cORREcT bIT. use only round, hex, or triangular
shank drill bits.
OPERATING SPEED. Always operate your drill
press at speeds that are appropriate for the drill bit
size and the material that you are drilling.
ADJUSTING KEyS AND WRENchES. remove
all adjusting keys and wrenches before turning the
machine ON.
MOUNTING WORKPIEcES. use clamps or vises
to secure workpiece before drilling. position work
so you avoid drilling into the table.
DRILLING ShEET METAL. never drill sheet
metal unless it is securely clamped to the table.
TAbLE LOcK. Make sure the table lock is tight-
ened before starting the drill press.
SURfAcE/WORKPIEcE PREP. never turn the
drill press ON before clearing the table of all
objects (tools, scrap wood, etc.) do not drill
material that does not have a flat surface, unless
a suitable support is used.
MAINTENANcE/SPEED chANGES. never
change speeds or do maintenance with the
machine connected to power.
EXPERIENcING DIffIcULTIES. if at any time
you are experiencing difficulties performing the
intended operation, stop using the machine!
Contact our technical support at (570) 546-9663.
DAMAGED TOOLS. never use drill bits in poor
condition. dull or damaged drill bits are hard to
control and may cause serious injury.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machines there is danger associated
with this machine. Accidents are frequently
caused by lack of familiarity or failure to pay
attention. Use this machine with respect
and caution to lessen the possibility of
operator injury. If normal safety precautions
are overlooked or ignored, serious personal
injury may occur.
-9-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 2: POWER SUPPLy
Availability
circuit Requirements for 220v
This machine is prewired to operate on a 220V
power supply circuit that has a verified ground and
meets the following requirements:
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrican or
qualified service personnel in accordance with all
applicable codes and standards.
Nominal voltage .............................. 220v/240v
cycle..........................................................60 hz
Phase.................................................... 3-Phase
Power Supply circuit ......................... 15 Amps
Plug/Receptacle ............................NEMA 15-15
cord........“S”-Type, 4-Wire, 14 AWG, 300 vAc
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
full-Load current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
full-Load current Rating at 220v .... 6.6 Amps
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuit—where only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the requirements in the following section.
-10-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
The power cord and plug specified under “Circuit
Requirements for 220V” on the previous page
has an equipment-grounding wire and a ground-
ing prong. The plug must only be inserted into
a matching receptacle (outlet) that is properly
installed and grounded in accordance with all
local codes and ordinances (see figure below).
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
a new one.
GROUNDED
15-15 RECEPTACLE
15-15 PLUG
Current
Carrying
Prongs
Grounding Prong
Extension cords
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
figure 2. neMA 15-15 plug and outlet.
Extension cords cause voltage drop, which may
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
contain a ground wire, match the required plug
and receptacle, and meet the following require-
ments:
No adapter should be used with the
required plug. If the plug does not fit the
available receptacle, or the machine must
be reconnected for use on a different type
of circuit, the reconnection must be made
by a qualified electrician and comply with all
local codes and ordinances.
Minimum Gauge Size...........................14 AWG
Maximum Length (Shorter is better).......50 ft.
-11-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 3: SETUP
Inventory
Unpacking
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at (570) 546-9663 for advice.
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
Inventory (see figure 3):
Qty
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
A. drill Chuck B16 3–16mm............................ 1
b. drill Chuck Arbor Mt#4–B16...................... 1
c. spindle sleeve Mt#4–Mt#3...................... 1
D. spindle sleeve Mt#4–Mt#2...................... 1
E. Bottle for oil ............................................... 1
f. drift Key...................................................... 1
G. Chuck Key .................................................. 1
h. toolbox (not shown) ................................... 1
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
A
B
C
d
Needed for Setup
e
g
the following are needed to complete the setup
process, but are not included with your machine.
Description
Qty
F
•
•
•
•
•
•
•
Additional people ....................................... 1
safety glasses ........................ 1 per person
Cleaner/degreaser ..................... As needed
disposable shop rags............... As needed
Forklift......................................................... 1
lifting straps (rated 1500 lbs. Minimum) .. 1
steel Bar stock 1" x 3'................................ 1
figure 3. toolbox inventory.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
-12-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
cleanup
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoid
using these products
to clean machinery.
the unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
this rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. the time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
Many cleaning solvents
are toxic if inhaled. Only
work in a well-ventilated
area.
there are many ways to remove this rust preven-
tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-
turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces.
before cleaning, gather the following:
•
•
•
•
disposable rags
Cleaner/degreaser (Wd•40 works well)
safety glasses & disposable gloves
plastic paint scraper (optional)
T23692—Orange Power Degreaser
A great product for removing the waxy shipping
grease from your machine during clean up.
basic steps for removing rust preventative:
1. put on safety glasses.
2. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3. Wipe off the surfaces. if your cleaner/degreas-
er is effective, the rust preventative will wipe
off easily. if you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
figure 4. t23692 orange power degreaser.
4. repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
-13-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Site considerations
Weight Load
Physical Environment
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
The physical environment where the machine is
operated is important for safe operation and lon-
gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20–95% (non-condensing); or the
environment is subject to vibration, shocks, or
bumps.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals,
or other hazards. Make sure to leave access to
a means of disconnecting the power source or
engaging a lockout/tagout device, if required.
Lighting
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
1
37 ⁄2
"
22"
30" minimum for
maintenance
30"
figure 5. Minimum working clearances.
-14-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Anchoring to floor
Lifting & Placing
Anchoring machinery to the floor prevents tipping
or shifting and reduces vibration that may occur
during operation, resulting in a machine that runs
slightly quieter and feels more solid.
hEAvy LIfT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a fork lift (or other
lifting equipment) rated for
weight of this machine.
if the machine will be installed in a commercial or
workplace setting, or if it is permanently connect-
ed (hardwired) to the power supply, local codes
may require that it be anchored to the floor.
if not required by any local codes, fastening the
machine to the floor is an optional step. if you
choose not to do this with your machine, we rec-
ommend placing it on machine mounts, as these
provide an easy method for leveling and they have
vibration-absorbing pads.
To move and place this drill:
1. place shipping crate near final machine
mounting location.
Anchoring to concrete floors
2. remove top portion of crate from the ship-
ping pallet, secure the ends of a properly
rated lifting strap around each side of the bar
placed through the lifting holes, and attach it
securely to your power lifting equipment (see
figure 6).
lag shield anchors with lag screws (see below)
are a popular way to anchor machinery to a con-
crete floor, because the anchors sit flush with the
floor surface, making it easy to unbolt and move
the machine later, if needed. however, anytime
local codes apply, you Must follow the anchoring
methodology specified by the code.
Lag Screw
Bar in
lifting
hole
Flat Washer
Machine Base
Lag Shield Anchor
figure 6. strap around bar in lifting hole.
3. unbolt the machine from the pallet.
Concrete
Drilled Hole
4. With another person to help to steady the
machine, lift it just enough to clear the pallet
and any floor obstacles, then place it in its
final position.
figure 7. popular method for anchoring
machinery to a concrete floor.
-15-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Arbor/chuck
Assembly
Initial Lubrication
An arbor is included for the drill chuck that
comes with this machine. the following procedure
describes how to install the arbor in the chuck.
GEARBOX MUST
BE FILLED WITH OIL!
After the arbor is installed in the drill chuck, it
is very difficult to separate the assembly. if you
would like to use a different chuck in the future,
we suggest using a different arbor.
OIL MAY NOT BE
SHIPPED WITH MACHINE!
Refer to Lubrication Section
for Correct Oil Type.
Important: DO NOT install the drill chuck and
arbor assembly until AFTER the test run.
To connect the drill chuck with the arbor:
to prevent spillage, this machine was shipped
from the factory without any oil in it. the head-
stock oil reservoir must be properly filled with oil
before the drill press can be operated for the first
time. refer to the Lubrication section, beginning
on Page 33, for details on how to check and add
oil.
1. use acetone or lacquer thinner to clean drill
chuck and arbor mating surfaces, especially
the bore.
2. retract the chuck jaws so that they are not
exposed.
3. insert the arbor into the drill chuck.
4. hold assembly by the arbor and tap chuck
onto a block of wood with moderate force
(see figure 8).
Damage caused by running the drill press
without oil in the reservoir will not be cov-
ered under warranty.
figure 8. installing arbor into chuck.
-16-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
2. identify the l1, l2, and l3 terminals and the
grounding terminal (see figure 9).
Power connection
3. thread the power cord through the strain
relief shown in figure 9.
Electrocution
or
fire
grounding terminal
may occur if machine is
ungrounded, incorrectly
connected to power, or
connected to an under-
sized circuit. Use an electri-
cian or a qualified service
personnel to ensure a safe
power connection.
l1 l2 l3
strain relief
Before the machine can be connected to the
power source, an electrical circuit must be made
available that meets the minimum specifications
given in circuit Requirements for 220v on Page
10. if a power circuit has not been prepared for the
machine, do that now.
figure 9. location of hot wire terminals, ground
terminal, and strain relief.
4. Connect the incoming hot wires and ground
wire to the terminals shown in figure 10.
to minimize the risk of electrocution, fire, or
equipment damage, all installation work and elec-
trical wiring Must be done by an electrician or
qualified service personnel.
Note: If using a phase convertor, the "wild
wire" is connected to the L2 terminal.
Note about extension cords: Using an incor-
rectly sized extension cord may decrease the life
of electrical components on your machine. Refer
to Extension Cords on Page 11 for more infor-
mation.
Mager
KBPC10-10
L1 L2 L3 U1 V1
L1 L2 L3 U1 V1
W
W
30
COM
To connect the power cord to the machine:
1. turn the master power switch to oFF, then
open the electrical cabinet door located at the
back of the machine.
To Plug/Power Supply
figure 10. ground and hot wires connected.
-17-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Make sure the power cord and wires have
slack between the strain relief and terminal
connections so that they do not bind, then
tighten the strain relief to secure the cord.
if, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review
Troubleshooting on Page 35.
Note: The strain relief must be tightened
against the outer jacket of the cord. Avoid
over-tightening the strain relief or it may
crush the cord and cause a short.
if you still cannot remedy a problem, contact our
tech support at (570) 546-9663 for assistance.
6. test the strain relief to ensure it is properly
tightened by pulling the cord from outside the
box with light-to-moderate force. When the
strain relief is properly tightened, the cord will
not move inside the cabinet.
before starting the drill press, make sure
you have performed the preceding setup
instructions, and you have read through the
rest of the manual and are familiar with the
various functions and safety features on
this machine. failure to follow this warning
could result in serious personal injury or
even death!
7. install a neMA 15-15 plug on the other end
of the power cord per the plug manufacturer's
instructions.
8. Close and secure the main electrical box
door.
To test run the machine:
9. plug the power cord into a power source with
a matching receptacle, as specified in circuit
Requirements for 220v on Page 10.
1. Make sure all tools and objects used during
setup are cleared away from the machine.
2. Make sure the machine is properly lubricated.
Note: If you discover during the Test Run that
the drill press will not operate, or that the spindle
runs backwards, the drill press may be wired out
of phase.
3. turn the Master power switch (figure 11)
ON.
Correcting the phase polarity requires reversing
the positions where the L1 and L3 wires are con-
nected. Due to the high voltage and risk of serious
shock involved, we strongly recommend this pro-
cedure only be done by an electrician or qualified
service personnel.
Master power switch
Test Run
figure 11. Master power switch.
once the preceding setup procedures are com-
plete, test run your machine to make sure it runs
properly and is ready for regular operation.
the test run consists of verifying the following:
1) the motor powers up and runs correctly, 2)
the eMergenCy stop button and chip guard
safety features work correctly, and 3) the motor
rotates in the correct direction (machine is not
wired out of phase).
-18-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. press the eMergenCy stop button
(figure 12) in, then twist it clockwise so
it pops out. When the botton pops out the
switch is reset and ready for operation.
6. press the eMergenCy stop button and
ensure that the drill press comes to a com-
plete stop.
7. Without resetting the eMergenCy stop
button, press the spindle start button. the
machine should not start.
—if the machine does not start, the
eMergenCy stop button safety feature
is working correctly.
eMergenCy
stop Button
—if the machine does start (with the
eMergenCy stop button pressed
in), immediately disconnect power to the
machine. the eMergenCy stop button
safety feature is not working correctly. this
safety feature must work properly before
proceeding with regular operations. Call
tech support for help.
spindle
stop
Button
spindle
start
Button
figure 12. resetting the switch.
8. press the eMergenCy stop button in,
then twist it clockwise so it pops out. When
the button pops out, the switch is reset and
ready for operation.
5. Verify that the machine is operating correctly
by turning the spindle rotation switch to the
left position and pressing the spindle start
button.
9. rotate the chip guard out of position and
press the spindle start button. the machine
should not start.
—When operating correctly, the machine
runs smoothly with little or no vibration or
rubbing noises.
—if the machine does not start, the chip
guard safety feature is working correctly.
—investigate and correct strange or unusual
noises or vibrations before operating the
machine further. Always stop the machine
and disconnect it from power before inves-
tigating or correcting potential problems.
—if the machine starts, immediately discon-
nect power to the machine. this safety fea-
ture must work properly before proceeding
with regular operations. Call tech support
for help.
—Verify that oil is flowing through the head-
stock by examining the oil flow sight glass
for oil movement (see Page 33).
Congratulations! the test run is now com-
plete. Before beginning any regular opera-
tions, perform the spindle Break-in proce-
dure on Page 21.
—if the spindle direction switch is turned to
the left and the bit turns from right to left
(as standing in front of the machine), it is
turning in the correct direction.
—if the bit turns from left to right (as standing
in front of the machine), see Page 17 for
instructions on correcting phase polarity.
-19-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. turn the Coolant pump switch to the on
position.
Test coolant System
4. Adjust the ball valve in the coolant nozzle
assembly for the proper coolant flow (see
figure 14).
this drill press comes with a pump-driven cycling
coolant system. prior to testing the coolant sys-
tem, add two gallons of coolant to the coolant res-
ervoir. refer to changing coolant on Page 28.
Ball valve
To test the coolant system:
1. Wear safety goggles and other protective
clothing.
2. Aim the coolant nozzle into the trough to
reduce splash (see figure 13).
figure 14. Ball valve of nozzle assembly.
5. Close the ball valve and turn the pump switch
to the oFF position.
Coolant drain
table trough
Running the pump without adequate cool-
ant can significantly damage the pump,
which will not be covered under warranty.
figure 13. table trough and coolant drain.
-20-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
To perform the spindle break-in procedure:
Spindle break-In
1. Move the drilling & tapping switch to the drill-
ing position (see figure 15).
Before subjecting the spindle to operational loads,
it is essential to complete the break-in process.
this helps ensure maximum life of spindle bear-
ings and other precision components by thor-
oughly lubricating them before placing them under
load.
drilling and
tapping
switch
After spindle break-in is complete, we recommend
changing headstock and gearbox oil to remove
any metal particles or debris that are present from
the assembly and break-in process.
spindle
start Button
the break-in must be performed in succession
with the Test Run procedure described in this
manual, as the steps in that procedure prepare
the drill press for the break-in process.
figure 15. drilling/tapping switch.
2. position the speed control levers for 440
rpM.
DO NOT perform this procedure indepen-
dently of the Test Run section. The drill
press could be seriously damaged if the
controls are set differently than instructed
in that section.
3. press the spindle start button.
4. Allow the machine to run for 10 minutes.
5. press the spindle stop button.
6. position the speed control levers for 870
rpM, and allow machine to run for 10 min-
utes.
7. press the oFF button, and adjust the speed
control levers for 440 rpM.`
8. press the spindle start button.
9. press the button on the end of the downfeed
handle to reverse spindle rotation.
10. run the machine at 440 rpM and then 870
rpM for 10 minutes each, as described
above.
11. run the machine at 440 rpM for another 15
minutes to allow it cool down.
Congratulations! spindle break-in is complete. We
recommend changing the headstock and gearbox
oil before operating the machine further (refer to
lubrication on Page 33).
-21-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 4: OPERATIONS
To complete a typical operation, the operator
does the following:
Operations Overview
1. examines the workpiece to make sure it is
suitable for drilling.
the purpose of this overview is to provide the nov-
ice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
2. puts on the required safety gear.
3. Firmly secures the workpiece to the table
using a vise or t-slot clamps.
due to the generic nature of this overview, it is
not intended to be an instructional guide. to learn
more about specific operations, read this entire
manual and seek additional training from expe-
rienced machine operators, and do additional
research outside of this manual by reading "how-
to" books, trade magazines, or websites.
4. installs the correct cutting tool for the opera-
tion.
5. Adjusts table to the correct height, then locks
it in place.
6. Connects the machine to power, and turns
the master power switch ON.
7. selects the spindle rpM with the speed
control levers and presses the spindle start
button.
To reduce your risk of
serious injury, read this
entire manual bEfORE
using machine.
8. Begins drilling.
9. When finished, presses the spindle stop but-
ton and disconnects it from power.
To reduce risk of eye injury from flying
chips or lung damage from breathing dust,
always wear safety glasses and a respirator
when operating this machine.
Tooling Installation &
Removal
this machine has an Mt#4 spindle for install-
ing tooling. it is also equipped with an automatic
drift for easy removal of tooling (see figure 16).
Additionally, a drift key is included to manually
remove the tooling from the spindle, if needed.
If you are not experienced with this type
of machine, WE STRONGLy REcOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj-
ects. Regardless of the content in this sec-
tion, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
-22-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. While holding onto the tooling, raise the
spindle to the original position. it should auto-
matically release from the spindle.
Installing Tapered Tooling
1. disConneCt MAChine FroM poWer!
2. Clean tooling and spindle tapers to ensure
proper seating.
4. pull the automatic drift knob back to the out-
ward position.
3. insert the Mt#4 tooling into the spindle, and
maneuver the tang until it engages with the
slot at the end of the spindle.
Removing Tooling Manually
1. disConneCt MAChine FroM poWer!
4. use a rubber or wooden mallet to seat the
tooling into the spindle by firmly tapping from
the bottom.
2. lower the quill and rotate the spindle by hand
until the drift key holes in the spindle and quill
are aligned (see figure 17).
Note: If installing a drill chuck, make sure to
retract the jaws to prevent damage to chuck.
Removing Tooling with Automatic
Drift
1. disConneCt MAChine FroM poWer!
2. lower the spindle with the coarse downfeed
handle until you can press in the automatic
drift knob (see figure 16).
figure 17. spindle and quill drift key holes
aligned.
3. insert the drift key into the aligned holes and
allow the quill to rise, trapping the drift key.
Automatic drift
4. softly tap the end of the key while holding the
arbor/chuck assembly until it separates from
the spindle (see figure 18).
figure 16. Automatic drift knob.
Leaving the automatic drift knob pressed in
can result in the arbor coming free the next
time it is inserted into the spindle sleeve.
An improperly installed arbor can become
a projectile and result in serious injury to
operator or others nearby. Always verify
arbor is correctly installed before beginning
drilling operations.
figure 18. using drift key to remove arbor.
-23-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
7. press the spindle start button.
Depth Stop
8. drill a hole into scrap stock before drilling into
any workpiece to ensure the depth has been
set correctly. if necessary, repeat Steps 2–5.
this drill press includes a depth stop for drilling
multiple holes at the same depth.
To set the depth stop:
Table Positioning
1. disConneCt MAChine FroM poWer!
the table for this drill press moves vertically
and rotates 360 degrees to accommodate larger
workpieces.
2. Adjust the table height so the workpiece is
close to the work tool.
3. Mark the side of your workpiece at the intend-
ed cutting depth (see figure 19).
Raising/Lowering Table
1. remove any objects from the table surface.
2. loosen the release handles shown in figure
21).
Workpiece
drill Bit
3. Adjust the table height by rotating the height
adjustment handle (see figure 21).
scrap Wood
Workpiece
depth
height
Adjustment
handle
Mark
table
figure 19. depth stop mark on workpiece.
lock handles
4. secure the workpiece to the table with a
clamp or vise.
5. place the workpiece on the table, and lower
the spindle until the tip of the bit is even with
the mark.
6. loosen the depth stop handle, move the drill
bit to the required drilling depth, and tighten it
(see figure 20).
figure 21. Column release and height
Adjustment handles.
Rotating Table
1. remove all objects from the table surface.
depth stop handle
2. slightly loosen the lock handles (see figure
21).
3. push the table to the desired location, and
guide the rack on the side of the column.
4. re-tighten the lock handles.
figure 20. setting depth stop handle.
-24-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: For carbide cutting tools, double the cut-
ting speed. These values are a guideline only.
Refer to the MACHINERY'S HANDBOOK for
more detailed information.
Selecting Spindle
RPM
use the proper spindle speed and feed rate to
reduce strain on all moving parts and decrease
risk of operator injury.
Larger bits turning at slower speeds tend
to grab the workpiece aggressively. This
can result in the operator's hand being
pulled into the bit or the workpiece being
thrown with great force. Always clamp the
workpiece to the table to prevent injuries.
prior to drilling, determine the rpM needed for
workpiece material then set the spindle speed to
the closest available rpM.
To determine the needed RPM:
1. use the table in figure 22 to determine the
speed required for your workpiece material.
Twist/Brad Point Drill Bits
Soft Wood Hard Wood Plastic Brass Aluminum
Mild Steel
2500
1250
600
1/16" – 3/16"
13/64" – 3/8"
25/64" – 5/8"
11/16" – 1"
3000
2000
1500
750
2500
1500
750
2500
2000
1500
1000
2500
1250
750
3000
2500
1500
1000
500
400
350
Spade/Forstner Bits
1/4" – 1/2"
Soft Wood Hard Wood Plastic Brass Aluminum
Mild Steel
2000
1500
1000
500
1500
1250
750
9/16" – 1"
1-1/8" – 1-7/8"
2–3"
350
Hole Saws
1/2" – 7/8"
1" – 1-7/8"
2" – 2-7/8"
3" – 3-7/8"
4" – 5"
Soft Wood Hard Wood Plastic Brass Aluminum
Mild Steel
500
500
400
300
200
100
500
400
300
200
100
600
500
400
300
200
600
500
400
300
200
600
500
400
300
200
400
300
200
100
Rosette Cutters
Carbide Insert Type
One-Piece Type
Soft Wood Hard Wood Plastic Brass Aluminum
Mild Steel
Mild Steel
350
1800
250
500
Tenon/Plug Cutters
3/8" – 1/2"
Soft Wood Hard Wood Plastic Brass Aluminum
1200
800
1000
600
5/8" – 1"
figure 22. Cutting speed table for hss cutting tools.
-25-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
To drill a workpiece:
Drilling Mode
1. refer to controls on Page 4 to understand
the functions of each control.
this drill press is designed for vertical drilling and
tapping operations. For repeated drilling at the
same depth, there is a power downfeed mecha-
nism. For tapping convenience, there is an auto-
matic clutch used for reversing the direction of the
spindle while in tapping mode by pressing one of
the buttons at the ends of each course downfeed
handle.
speed Control levers
drilling/taping switch
Overloading tools or using excessive spin-
dle speeds may cause parts or broken tools
to hit operator, resulting in serious impact
injuries.
figure 23. Controls for drilling.
2. Clamp the workpiece to the table, and adjust
the depth stop for the needed depth of cut.
Note: Drilling with the quill fully extended
can cause tool chatter. For maximum spindle
rigidity, keep the spindle retracted into the
headstock as far as possible.
3. put on safety glasses, a face shield, and
close the chip guard.
4. select the "drilling" mode option with the
toggle switch.
5. refer to Selecting Spindle RPM on Page
25, and choose the closest available spindle
rpM.
6. turn the Master power switch ON.
7. press the spindle start button and begin the
drilling operation.
-26-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Match the lines on the adjustment knob to
select an automatic power downfeed option
(see figure 24).
Automatic Power
Downfeed
—there are three options for the power
downfeed mechanism that are located on the
side of the adjustment knob:
this drill press comes with automatic downfeed
control for repeated drilling operations at the
same depth. the automatic downfeed only works
in the drilling mode.
•
•
•
0.2 is equal to 2mm of downfeed per
spindle rotation.
0.1 is 1mm of downfeed per spindle
rotation.
0.0 disengages the downfeed mecha-
nism.
Stay clear of coarse downfeed handles
while using the automatic downfeed. When
the depth stop triggers the lower elevation
limit switch, the handles spin rapidly as
the spindle returns to its starting position.
failure to stay clear of the handles may
result in injury.
Adjustment Knob
Automatic
power
downfeed
option lines
To operate the automatic power downfeed:
1. disConneCt MAChine FroM poWer!
2. select the drilling option with the drilling/tap-
ping switch.
3. set the spindle depth stop to the desired
position (refer to Page 24).
figure 24. Automatic downfeed adjustment
knob.
5. re-connect machine to power.
6. turn the Master power switch ON, and press
the spindle start button.
7. pull the coarse downfeed handle down
towards the front of the machine until the
automatic downfeed begins.
-27-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
coolant System
Tapping Mode
this machine comes with a coolant system for
use in drilling and tapping operations. this feature
promotes precision cutting and tool longevity.
When in tapping mode, the spindle direction
can immediately alternate between forward and
reverse by pressing any of the three buttons at the
end of the downfeed handles. this feature is criti-
cal to back the tap out of a hole before it bottoms
out and snaps off, as well as clearing away waste
chips during the tapping process.
To operate the coolant system:
1. ensure there is a sufficient amount of clean
coolant in the reservoir (refer to Page 20 for
detailed instructions).
pilot holes must be drilled prior to beginning any
tapping operation.
2. Aim the coolant nozzle at the contact area of
the workpiece and the work tool.
To use tapping mode:
3. turn the coolant pump switch on the control
panel to the on position.
1. disConneCt MAChine FroM poWer!
2. determine the maximum tapping depth with-
out bottoming-out the tap, and adjust the
depth stop accordingly.
4. regulate the coolant flow to the contact area
using the coolant ball valve shown in figure
25.
3. Clamp the workpiece to the table.
4. put on safety glasses and a face shield.
select tapping mode, and turn the spindle
rotation switch counter-clockwise.
Coolant Ball Valve
5. install the tap, and apply tapping fluid to the
contact point of the tap and workpiece.
6. Connect the machine to power.
7. select "tapping" mode with the drilling/tap-
ping switch
8. select the appropriate spindle speed. speeds
vary according to the material, bit, and proce-
dure. there are several online resources to
choose from for calculating spindle speed
figure 25. Coolant ball valve.
9. press the spindle start button.
10. Begin threading. Without disengaging the
tap from the threads, frequently alternate
spindle rotation by pressing any end button
to reverse spindle and eject chips from the
hole. Frequently removing chips will prevent
galling and tap breakage.
-28-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 5: AccESSORIES
G1075—52-Pc. clamping Kit
this clamping kit includes 24 studs, 6 step block
pairs, 6 t-nuts, 6 flange nuts, 4 coupling nuts, and
6 end hold-downs. the rack is slotted so it can be
mounted close to the machine for easy access.
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
1
Made for ⁄2" t-slots.
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
G5753—Drill Press vise - 6"
if you use a drill press and value your fingers, you
need one of these. Made from high-grade cast
iron, these hefty horizontal vises offer support
and stability, allowing you to keep your hands well
away from fast moving bits and cutters. includes
a sturdy lip along both sides of the base, allowing
vise to be mounted to nearly any machine table,
using common t-slot clamps.
figure 27. Clamping Kit.
T20501—face Shield crown Protector 4"
T20502—face Shield crown Protector 7"
T20503—face Shield Window
T20452—"Kirova" Anti-Reflective S. Glasses
T20451—"Kirova" clear Safety Glasses
h0736—Shop fox® Safety Glasses
h7194—bifocal Safety Glasses 1.5
h7195—bifocal Safety Glasses 2.0
h7196—bifocal Safety Glasses 2.5
figure 26. Cast iron drill press vice.
figure 28. safety glasses.
-29-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
T23962—ISO 68 Moly-D Way Oil, 5 gal.
T23963—ISO 32 Moly-D Machine Oil, 5 gal.
Moly-d oils are some of the best we've found for
maintaining the critical components of machinery
because they tend to resist run-off and maintain
their lubricity under a variety of conditions—as
well as reduce chatter or slip. Buy in bulk and
save with 5-gallon quantities.
G3658—Titanium Drill bits
titanium nitride-coated bits last up to six times as
long as uncoated bits. this 115-piece set features
1
1
29 fractional bits, from ⁄6" to ⁄2" in increments
1
of ⁄64", letter bits from A–z, and 60 number bits.
housed in rugged steel case.
t23962
t23963
figure 29. iso 68 and iso 32 machine oil.
figure 31. 115 piece drill bit set.
h7527—6" ROTARy TAbLE SET
h7616—Oil can w/Plastic Nozzle
use this 6" rotary table in either the horizontal
or vertical position for a variety of milling appli-
cations and with the set of dividing plates and
adjustable tailstock, your milling applications are
nearly unlimited. With 4° table movement per han-
h7617—Oil can w/flexible Plastic Nozzle
these high-pressure oil cans are perfect for lubri-
cating the ball oilers found on your machine. each
can holds 5 ounces of oil.
dle rotation and 20 second vernier scale, control
3
is very accurate and precise. Also includes a ⁄8
"
clamping set for the 4-slot table. everything you
need in one great set!
h7616
h7617
figure 32. high pressure oil cans.
figure 30. rotary table with dividing plates.
-30-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
h8262—1⁄2" x MT#4 Keyless chuck with
Integral Shank
h7819—Drill & Tap hSS 24 pc. Set
our new high speed steel tap and drill set
comes supplied with 6 of the most commonly
used coarse thread sizes. What's more, each size
has taps with plug, bottoming and taper grinds
allowing you to choose the right tap for any job.
the set includes the following tap sizes and corre-
sponding drill bits: 8-32 & #29, 10-24 & #25, 1⁄4"-20
precision, Keyless drill Chucks have integral
shanks to fit a variety of spindles including Morse
taper, r8 and Cat 40. each chuck has a knurled
grip for plenty of torque and if that’s not enough,
they’re spanner wrench compatible. (spanner
wrench not included.) Made in an iso 9001 certi-
fied factory.
1
& #7, 5⁄16"-18 & F, 3⁄8"-16 & 5⁄16" and ⁄2"-13 & 27⁄64".
figure 34. precision keyless drill chuck.
figure 33. Commonly used tap and drill set.
-31-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 6: MAINTENANcE
Daily, After Operations
•
thoroughly clean the machine and protect all
surface areas
To reduce risk of shock or
accidental startup, always
disconnect machine from
power before adjustments,
maintenance, or service.
•
press the eMergenCy stop button and
shut OFF the master power switch (to pre-
vent accidental startup).
remove any rotary tables, vises, fixtures, or
workpieces from the table to prevent rusting
the table surface.
•
Schedule
Annually
typically, each operator is responsible for ensur-
ing proper care of the equipment. We strongly
recommend all operators make a habit of follow-
ing the daily maintenance procedures.
•
disconnect machine from power, open elec-
trical box, and clean with compressed air.
cleaning and
Ongoing
to reduce the risk of injury and ensure proper
machine operation, if you ever observe any of the
items below, shut down the machine immediately
and fix the problem before continuing operations:
Protecting
Metal chips left on the machine will invite oxida-
tion and a gummy residue build-up around the
moving parts. use a brush and shop vacuum to
remove chips and debris from the working sur-
faces of the drill press. never blow off the drill
press with compressed air, as this will force metal
chips deep into the mechanisms and may cause
injury to yourself or bystanders.
•
•
•
•
loose mounting bolts or fasteners.
Worn, frayed, cracked, or damaged wires.
Chip guard removed.
eMergenCy stop button not working cor-
rectly or not requiring you to reset it before
starting the machine again.
•
Any other unsafe condition.
remove any rust build-up from unpainted cast
iron surfaces of your drill press and treat with a
non- staining lubricant after cleaning.
Every 8 hour of operation:
•
•
•
lubricate the ball oilers (Page 34).
Check/Add headstock oil (Page 33).
Check quantity/quality of coolant (Page 20).
Keep unpainted cast iron surfaces rust-free with
regular applications of iso 68 way oil (see Page
30 for offerings form grizzly).
Annually:
•
Change headstock oil (Page 33).
-32-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
Do not fill headstock with oil above the red
mark. This could damage the machine and
create an overflow of oil.
For the quill, table, and column, an occasional
application of light machine oil is all that is neces-
sary. Before applying lubricant, clean off any dust
or metal chips.
your goal is to achieve adequate lubrication. too
much lubrication will attract dirt and dust. Various
parts of your machine could lose their freedom of
movement as a result.
red Mark
headstock Lubrication
oil type ......Model t23963 or iso 32 equivalent
oil Amount...........................................43⁄4 quarts
lubrication Frequency........................... Annually
site glass
location
the headstock uses an oil pump to lubricate the
gears. For this machine, use iso 68 machine
oil. Check the oil level every day (see Step 4).
Change oil annually.
figure 36. site glass location.
5. re-install the oil fill plug.
To change oil in headstock:
6. discard used oil following federal, state, and
fluid manufacturer guidelines for proper dis-
posal.
1. remove the oil fill plug on top of the machine
(see figure 35).
Oil flow Sight Glass
this machine comes with an oil flow sight glass
(see figure 37). examine the flow sight glass
during machine operation to ensure that the oil is
properly circulating within the headstock.
oil Fill plug
if oil is not circulating, and headstock has proper
amount of oil, shut down machine immediately
and call tech support.
oil drain plug
oil Flow sight glass
figure 35. oil fill and drain locations.
2. remove the drain plug, and allow old oil to
drain into an appropriate container.
3. replace and tighten the drain plug.
4. Fill the headstock with oil to the red mark on
the site glass (see figure 36).
figure 37. oil flow sight glass.
-33-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
ball Oilers
oil type ......Model t23963 or iso 32 equivalent
oil Amount.........................................1–2 pumps
lubrication Frequency........8 hours of operation
changing coolant
Coolant is consistently cycled and stored in the
base reservoir beneath the pump. For efficient
operation and tool longevity, replace coolant when
it runs low or becomes dirty from excessive use.
this machine has four ball oilers as shown in
figures 38–39. use an oil gun fitted with a rub-
ber tip wide enough to seal the ball oiler inlet. We
do not recommend using metal needle or lance
tips, as they can push the ball too far into the oiler,
break the spring seat, and lodge the ball in the oil
galley.
bIOLOGIcAL & POISON hAzARD!
Use the correct personal protection equip-
ment when handling coolant. follow fed-
eral, state, and fluid manufacturer require-
ments for proper disposal.
push the tip of the oil can nozzle against the ball
oiler to create a hydraulic seal, then pump the oil
can once or twice. if you see sludge and contami-
nants coming out of the lubrication area, continue
pumping the oil can until the oil runs clear. When
finished, wipe away the excess oil.
To replace the coolant:
1. pump coolant into an empty 5-gallon bucket.
As soon as coolant stops coming out, shut off
pump.
2. disConneCt MAChine FroM poWer!
3. put on gloves, safety glasses, and respira-
tor. loosen the cap screws and remove the
reservoir lid (see figure 40).
Ball oilers
Coolant reservoir lid
figure 38. table support bracket ball oiler
locations.
figure 40. Coolant reservoir.
Ball oilers
4. use a wet/dry shop vacuum to remove any
coolant and debris from inside the reservoir.
5. refill the reservoir with fresh coolant.
6. replace the reservoir lid and re-tighten the
cap screws.
figure 39. headstock side ball oiler locations
-34-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 7: SERvIcE
Review the troubleshooting and procedures in this section if a problem develops with your machine. If you
need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.
Note: Please gather the serial number and manufacture date of your machine before calling.
Troubleshooting
Motor & Electrical
Symptom
Possible cause
Possible Solution
Machine does not 1. emergency stop push-button engaged/at 1. rotate button to reset/replace it.
start or a breaker
trips
fault.
2. Chuck guard open/safety switch at fault.
2. Close guard/replace switch.
3. spindle position limit switch engaged/at 3. Adjust spindle position to disengage limit switch;
fault.
replace switch.
4. power supply switched oFF or at fault.
5. plug/receptacle at fault/wired wrong.
6. Motor connection wired wrong.
7. Wall circuit breaker tripped.
8. Wiring open/has high resistance.
9. Master power switch at fault.
10. Motor or motor components at fault.
4. ensure power supply is on/has correct voltage.
5. test for good contacts; correct the wiring.
6. Correct motor wiring connections (Page 41).
7. ensure circuit size is correct/replace weak breaker.
8. Check/fix broken, disconnected, or corroded wires.
9. replace switch.
10. test/repair/replace.
Machine stalls or is 1. Feed rate/cutting speed too fast.
1. decrease feed rate/cutting speed.
2. use the correct tool for the task.
overloaded.
2. Wrong tooling.
3. Machine is undersized or tooling is incorrect 3. use smaller or sharper tool; reduce feed rate or
for the task.
spindle speed; use coolant if possible.
4. Correct motor wiring connections (Page 41).
5. test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
4. Motor connection is wired incorrectly.
5. Motor bearings are at fault.
6. Motor has overheated.
6. Clean off motor, let cool, and reduce workload.
7. test/repair/replace motor.
7. Motor or motor components at fault.
Machine has
vibration or noisy
operation.
1. excessive depth of cut.
1. decrease depth of cut.
2. tooling is loose or improperly installed.
2. Make sure tooling is properly secured.
3. Machine is incorrectly anchored or sits 3. tighten/replace anchors; relocate/shim machine.
unevenly.
4. Motor or machine component is loose.
4. inspect/replace stripped or damaged bolts/nuts, and
re-tighten with thread locking fluid.
5. tooling is dull or at fault.
6. Bit is chattering.
5. replace/resharpen tooling.
6. replace/sharpen bit; index bit to workpiece; use
appropriate feed rate and cutting rpM.
7. Motor fan is rubbing on fan cover.
8. Motor bearings are at fault.
7. replace dented fan cover or damaged fan.
8. test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
-35-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill Press Operations
Symptom
Possible cause
Possible Solution
Breaking tools or cutters.
1. spindle speed/feed rate is too fast. 1. set spindle speed correctly (Page 25) or use a
slower feed rate.
2. Cutting tool getting too hot.
2. use coolant or oil for appropriate application.
3. Fully retract spindle and lower headstock. this
increases rigidity.
3. spindle extended too far down.
drilling stops, but the motor 1. Bit slips in chuck.
still operates.
1. tighten bit; inspect bit for burrs or other obstructions
that might interfere with clamping surface.
the chuck wobbles or is 1. Foreign material is stuck between 1. remove the arbor/chuck assembly and clean the
loose on the spindle shaft.
the arbor-to-spindle mating surface.
tapered arbor and spindle mating surfaces, then
reassemble.
2. damaged chuck or arbor.
2. replace as necessary.
the spindle does not retract 1. the quill shaft is gummy with metal 1. Clean shaft and lubricate with a light coat of oil.
completely in the uppermost
position or it binds.
chips and oil.
the quill has excessive 1. the quill bearings are worn or 1. replace the bearings.
deflection.
damaged.
2. the quill shaft is at fault.
2. replace the quill shaft.
drill bit wobbles, holes are 1. drill bit installed incorrectly.
oversized.
1. remove drill bit and re-install.
Workpiece vibrates or
1. table locks not tight.
1. tighten table release handles (Page 24).
chatters during operation.
2. Workpiece not securely clamped to 2. Check that clamping is tight and sufficient for the job.
table or into drill vice. Make sure drill vice is tight to the table.
3. spindle speed/feed rate is too fast. 3. set spindle speed correctly (Page 25) or use a
slower feed rate.
4. spindle extended too far down.
4. Fully retract spindle and raise table. this increases
rigidity.
-36-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque Limiter
Replacing Lamp
bulb
the torque limiter regulates how much torque
is applied to the drive shaft of the drill press to
prevent the machine from mechanical overload. it
was adjusted at the factory according to the maxi-
mum axial load.
the work lamp bulb in this machine is a 24V 25W
two pronged halogen bulb. the replacement part
number for the bulb is p0756418-1.
eventual wear on the limiter discs may require
compensatory adjustment to the torque limiter.
To replace the bulb in the work lamp:
1. disConneCt MAChine FroM poWer!
2. using a phillips head screwdriver, remove
the three screws that hold the work lamp
cover in place.
Overtightening can break the torque limiter.
Make less than quarter turn adjustments at
one time.
3. remove the bulb (see figure 41).
To adjust the torque limiter:
1. disConneCt MAChine FroM poWer!
2. remove the two cap screws that hold the
plastic cover on the side of the headstock.
3. rotate the spindle by hand until the set screw
on the torque limiter is visible (see figure
42).
set screw
figure 41. Work lamp bulb replacement.
torque limiter
4. insert the new bulb and replace the work
lamp cover.
figure 42. torque limiter and set screw.
4. turn the set screw less than a quarter of a
turn using a 4mm hex wrench. one small
adjustment should compensate for any wear
on the limiter disc.
-37-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
machine
SEcTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-
es to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is con- WIRE/COMPONENT DAMAGE. Damaged wires
nected to a power source is extremely dangerous. or components increase the risk of serious per-
Touching electrified parts will result in personal sonal injury, fire, or machine damage. If you notice
injury including but not limited to severe burns, that any wires or components are damaged while
electrocution, or death. Disconnect the power performing a wiring task, replace those wires or
from the machine before servicing electrical com- components.
ponents!
MOTOR WIRING. The motor wiring shown in
MODIFICATIONS. Modifying the wiring beyond these diagrams is current at the time of printing
what is shown in the diagram may lead to unpre- but may not match your machine. If you find this
dictable results, including serious injury or fire. to be the case, use the wiring diagram inside the
This includes the installation of unapproved after- motor junction box.
market parts.
CAPACITORS/INVERTERS. Some capacitors
WIRE CONNECTIONS. All connections must and power inverters store an electrical charge for
be tight to prevent wires from loosening during up to 10 minutes after being disconnected from
machine operation. Double-check all wires dis- the power source. To reduce the risk of being
connected or connected during any wiring task to shocked, wait at least this long before working on
ensure tight connections.
capacitors.
CIRCUIT REQUIREMENTS. You MUST follow EXPERIENCING DIFFICULTIES. If you are expe-
the requirements at the beginning of this man- riencing difficulties understanding the information
ual when connecting your machine to a power included in this section, contact our Technical
source.
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
-38-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Overview
elevation limit
switches
spindle Motor
Page 41
Control
Page 43
panel
Page 43
Master
power
switch
Chip guard
limit switch
Page 43
Page 45
electrical
panel
Page 45
electronic
Clutch
Page 40
Work lamp
Page 41
Coolant
pump Motor
power supply Connection
Page 40
Page 41
component Location Index
spindle Motor
Page 41
Control
panel
Page 43
d
Master power
switch
Page 45
elevation limit
switches
Page 43
electrical
panel
b
Page 45
Chip guard
limit switch
Page 43
power plug
Page 40
i
Work lamp
Page 41
Coolant
pump
Page 41
READ ELECTRICAL SAFETY
ON PAGE 38!
-39-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Power connection Wiring
hot
ground
G
hot
Z
X
220 vAc
3-Phase
W
hot
15-15 Plug
(as recommended)
Electric clutch Wiring
to electrical
panel
Page 45
13
QO
gd.
PE
ground
Front View
side view
figure 43. electronic clutch wiring.
READ ELECTRICAL SAFETY
ON PAGE 38!
-40-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor & Pump Wiring
W2
U2
V2
U1
V1
to
Control
panel
Page 43
W1
Ground
PE
SPINDLE MOTOR
figure 44. spindle motor wiring.
figure 45. Coolant pump wiring.
figure 46. Work lamp wiring.
Ground
to
electrical
panel
W1
U2
V2
V1
V2
Page 45
U2
U1
W2
W2
PUMP MOTOR
WORK LAMP
to
Control
panel
Page 43
13
READ ELECTRICAL SAFETY
ON PAGE 38!
-41-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
control Panel
to lamp
to electrical panel
to electrical panel to spindle Motor
Page 41
Page 45
Page 45
Page 41
PE
Ground
12
X5
X6
C2SS2-10B-10
C2SS2-10B-10
X6
LX5W-A11N
LAMP SWITCH
PUMP SWITCH
Upper
Elevation
Limit
Left
View
U1
V1
2
4
6
10 14
16
12
8
Switch
W2
2
W1
MCB-01
V1
V2
Right
View
U2
1
U1
1 3 5 7 9 1113
W1
15
EMERGENCY STOP
HIGH/LOW GEAR SWITCH
X2
X4
C2SS2-10B-10
C2SS2-10B-10
Lower
Elevation
Limit
SPINDLE DIRECTION
DRILLING/TAPPING SWITCH
Switch
LX5W-A11N
COM
12
10
X7
4
X1
X7
MCB-01 MLB-01
CP1-10R-01
X2
3
X1
Ground
STOP BUTTON
10
START BUTTON
PE
Chip
Guard
Limit
(Viewed from behind)
Switch
Machine Frame
READ ELECTRICAL SAFETY
ON PAGE 38!
-42-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
control Panel & Limit Switches
Chip guard
limit switch
upper elevation
limit switch
figure 47. Chip guard limit switch
location.
lamp switch
pump switch
emergency
stop Button
high/low
gear switch
drilling/tapping
Mode switch
spindle direction
switch
start Button
stop Button
lower elevation
limit switch
figure 31. Control panel and limit switch locations (viewed from behind).
READ ELECTRICAL SAFETY
-43-
Model G0756 (Mfg. Since 2/13)
ON PAGE 38!
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Panel Wiring
Master Power Switch
L2
8
6
4
2
3L3
3L1
31
11
2L1
2L3
L1
L2
L3
21
L3
DZ451-63
DZ451-63
DZ451-63
DZ451-63
QM5 DQZ4M51-363 QM2
QM1
QM4
L1
26
25
24
23
22
21
20
L
20-21 = 220V
C1
ON
C3
D1
ON
D10
C1
ON
L3
R
ON
ON
20-22 = 230V
20-23 = 380V
20-24 = 400V
20-25 = 415V
20-26 = 440V
Transformer
OFF
OFF
OFF
OFF
OFF
JBK5-100VATH
TC
E
7
5
3
1
30 31
32 33 34 35
3L1
3L3
2L1
ZL2
2L3
L1
L2
32
22
12
20
21
30
31
10
11
CM
22 20 X1X3
X5X7
L
X1 X3 CM X5 X7 CM X11 X13 CM X15 X17 CM
2L1 ZL2 2L3 Q2
2L1 ZL2 2L3 Q1
1 L1 3 L2 5 L3 21NC
3L1 ZL2
3L3
10
10
10
X4X6
X2
10
A1
A1
A1
N
X0 X2
•
X4 X6
•
X10 X12
•
X14
T
+24v
1 L1 3 L2 5 L3 21NC
13NO 23NO 33NO 43NO
Tianshui 123
GSC1-1201
Tianshui 123
GSC1-1201
Tianshui 123
JZC3-40d
E&E
Special Controller
Contactor
KM1
2 T1 4 T2 6 T3 22NC
Contactor
KM2
2 T1 4 T2 6 T3 22NC
Contactor
KA1
14NO 24NO 34NO 44NO
EX-30tA1-B
PLC
•
Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7
•
•
•
•
A2
A2
A2
Q0
Q2
Q1
Q3
35
36
Q3
U2 V2 W2
W1 V1 U1 35
U1 V1 W1 36
CM CM CM CM CM
•
•
•
•
•
•
•
•
0
1
2
2
2
12
12
To High/Low To
Gear Switch Pump
To Control
Panel
To Electronic
Clutch
32 PE
COM
PE PE
L1 L2 L3 U1 V1 W1 U2 V2 W2 10 12
L1 L2 L3 U1 V1 W1 U2 V2 W2 10 12
L1 L2 L3 U1 V1 W1 U2 V2 W2 10 12
X1 X2 X3 X4 X5 X6 X7 QO
10 11 12 13 14 15 16 17 QO
X1 X2 X3 X4 X5 X6 X7 QO
Mager
KBPC10-10
COM
COM
30
COM
To Plug/Power Supply
READ ELECTRICAL SAFETY
ON PAGE 38!
-44-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Wiring Panel Photo
figure 48. electrical wiring panel.
READ ELECTRICAL SAFETY
-45-
Model G0756 (Mfg. Since 2/13)
ON PAGE 38!
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 9: PARTS
Table Support & coolant breakdown
14
13
34
33
11
10
9
32
8
29
30
7
6
15
16
28
27
26
17
31
5
4
19
18
20
25
3
2
24
23
22
21
1
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-46-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Support & coolant Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
P0756001
P0756002
PCAP26M
P0756004
PCAP26M
P0756006
P0756007
PSS127M
P0756009
P0756010
P0756011
PCAP49M
P0756014
P0756015
PCAP13M
P0756017
P0756018
BASE
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
P0756019
DRAIN PLUG 3/8" NPT SOCKET HEAD
2
COOLANT PUMP MOUNT
CAP SCREW M6-1 X 12
COOLANT PUMP
PCAP209M CAP SCREW M14-2 X 60
3
P0756021
PCAP31M
P0756023
P0756024
P0756025
P0756026
P0756027
P0756028
PSS16M
COOLANT RESERVOIR COVER PLATE
4
CAP SCREW M8-1.25 X 25
REDUCING NIPPLE 1/2" X 3/8" NPT
ELBOW
5
CAP SCREW M6-1 X 12
HANDLE SHAFT 3/8"-16 x 3"
CRANK ARM
6
7
FLEXIBLE TUBE 16 X 1.5 X 1300MM
COOLANT RETURN HOSE
COUPLING
8
SET SCREW M10-1.5 X 10 PILOT
CLAMP COLLAR
9
10
11
13
14
15
16
17
18
WORM GEAR M16-2
ADJUSTABLE HANDLE M16 X 114
CAP SCREW M6-1 X 60
HEADSTOCK MOUNT
GEAR 15T
TEE
SET SCREW M8-1.25 X 10
PLUBE002M BALL OILER 8MM TAP-IN
P0756031
P0756032
P0756033
GEAR SHAFT
TABLE SUPPORT
TABLE
CAP SCREW M8-1.25 X 30
RACK
PCAP122M CAP SCREW M16-2 X 50
COLUMN
-47-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Gearbox breakdown
102-3
102-5
102-1
102-2
102-4
101
103
104
134
133
102
132
131
105
106
107
130
129
128
127
108
109
126
125
124
110
111
135
136
112
113
123
114
122
121
115
114
116
119 118
117
-48-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Gearbox breakdown 2
142
151
141
150
140
149
139
148
138
147
137
143
146
158
164
145
157
144
156
154
155
155
154
153
156
152
163
162
161
167
172
160
171
159
155
170
169
164
155
168
175
156
166
165
180
179
178
176
177
185
186
184
183
174
173
182
181
-49-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Gearbox Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
101
102
P0756101
P0756102
GEARBOX HOUSING
MOTOR 2HP 220V 3-PH 4/8-POLE
MOTOR FAN COVER
MOTOR FAN
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
P0756142
PR32M
SPLINED SHAFT
EXT RETAINING RING 48MM
GEAR 34T
102-1 P0756102-1
102-2 P0756102-2
102-3 P0756102-3
102-4 P0756102-4
102-5 P0756102-5
P0756144
P0756145
P0756146
P0756147
PR32M
KEY 8 X 5 X 32
JUNCTION BOX
GEAR 46T
FRONT MOTOR BEARING 6206 2RZ
REAR MOTOR BEARING 6206 2RZ
FLAT WASHER 10MM
CAP SCREW M10-1.5 X 35 C12.9
MOTOR GASKET
GEAR 40T
EXT RETAINING RING 48MM
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
PW04M
P6008-OPEN BALL BEARING 6008-OPEN
PCAP210M
P0756105
P0756019
PCAP31M
P0756108
P0756109
P0756110
P0756111
PCAP31M
P0756113
P0756114
P0756115
P0756116
P0756117
PCAP14M
P0756119
P0756121
P0756122
P0756123
P0756124
PSTB005M
P0756126
PR09M
P0756150
PR38M
SPACER
INT RETAINING RING 62MM
COVER
DRAIN PLUG 3/8" NPT HEX HEAD
CAP SCREW M8-1.25 X 25
SIGHT GLASS M27 X 1.5
SIGHT GLASS B20 x M27-1.5
DRAIN PLUG M27-2 HEX HEAD
PLUG
P0756152
P0756153
PR38M
O-RING 58 X 2.65
INT RETAINING RING 62MM
P6206-OPEN BALL BEARING 6206-OPEN
P0756156
P0756157
P0756158
P0756159
P0756145
P0756161
P0756162
P0756163
P0756164
PCAP01M
P0756166
P0756167
P0756168
PSS97M
FLANGED BUSHING
GEAR 48T
CAP SCREW M8-1.25 X 25
SHIFT LEVER
GEAR 48T
GEAR SHAFT
SHIFT FORK
KEY 8 X 5 X 32
KEY 8 X 5 X 40
GEAR 22T
SHAFT
SHIFT LEVER
SHAFT
GEAR 28T
CAP SCREW M8-1.25 X 20
POINTER PIN
COVER
CAP SCREW M6-1 X 16
DOWEL PIN 10 X 40MM
FLANGE
HANDLE LEVER
RIGHT SHIFT HUB
LEFT SHIFT HUB
O-RING 58 X 2.65
SET SCREW M3-.5 X 4
GEAR 12T
COMPRESSION SPRING 1 X 9 X 18-2
STEEL BALL 10MM
P0756170
P0756171
P0756172
P0756173
P0756174
P0756175
P0756176
P0756177
PR12M
O-RING 17 X 1.8
FLANGED BUSHING
SPLINED SHAFT
GEAR 20T
EXT RETAINING RING 20MM
PHLP HD SCR M5-.8 X 12
GEAR CHANGE PLATE
ROLL PIN 5 X 12
PS08M
P0756129
PRP59M
KEY 6 X 4 X 36
GEAR 34T
P0756019
P0756132
PCAP03M
P0756134
P0756135
P0756136
P0756137
P0756138
P0756139
PR70M
DRAIN PLUG 3/8" NPT HEX HEAD
LUBRICATION TUBE
CAP SCREW M5-.8 X 8
TUBE CLIP
GEAR 12T
GEAR 50T
EXT RETAINING RING 35MM
EXT RETAINING RING 25MM
GEAR 50T
PR11M
GEARBOX COVER GASKET
GEARBOX COVER
P0756180
PCAP14M
PLW04M
PWF08M
P0756184
P0756185
P0756186
CAP SCREW M8-1.25 X 20
LOCK WASHER 8MM
FENDER WASHER 8MM
GEAR SHAFT
SPLINED FLANGE SLEEVE
O-RING 61.5 X 3.55
OIL SEAL 40 X 55 X 08MM
INT RETAINING RING 68MM
BALL BEARING 6008-2RS
KEY 6 X 4 X 28
SHAFT
P6008-2RS
-50-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Spindle feed breakdown
203
204
205
201
202
206
207
208
209
210
212
213
214
215
216
227
217
218
219
220
221
222
223
228
225
226
224
230
231
229
232
233
-51-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Spindle feed Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201 PS14M
PHLP HD SCR M6-1 X 12
PLATE
218 P16005-OPEN BALL BEARING 16005-OPEN
202 P0756202
203 PRP09M
204 P0756204
205 P0756205
206 P0756206
207 P0756206
208 PR73M
219 PR25M
INT RETAINING RING 47MM
FEED HANDLE HUB
ROLL PIN 6 X 5
220 P0756220
221 P0756221
222 P0756222
223 PCAP110M
224 P0756224
225 PCAP110M
226 P0756226
227 P0756227
228 P0756228
229 PCAP12M
230 P0756230
231 P0756231
232 P0756232
233 PRP86M
COILED SPRING
SPANNER NUT M24-1.5
HUB COVER PLATE
GEAR SHAFT
WOODRUFF KEY 8 X 5
WOODRUFF KEY 8 X 5
EXT RETAINING RING 5MM
WORM GEAR
CAP SCREW M4-.7 X 6
HEADSTOCK FEED COVER GASKET
CAP SCREW M4-.7 X 6
BRACKET
209 P0756209
210 P0756210
212 P0756212
213 PCAP16M
214 P0756214
215 P0756215
216 P0756216
217 PR25M
ELECTROMAGNETIC TOOTH CLUTCH
ARMATURE
NUT
BRUSH
CAP SCREW M4-.7 X 16
FLANGED BUSHING
GEAR SHAFT SPACER-LARGE
GEAR SHAFT SPACER-SMALL
INT RETAINING RING 47MM
CAP SCREW M8-1.25 X 40
HANDLE SHAFT W/BUTTON HOUSING
BUTTON RETAINER NUT
HEADSTOCK FEED SPINDLE COVER
ROLL PIN 8 X 45
-52-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
headstock breakdown
307306
314
312
309308
305
310
304
303
311
302
313
301
318
319
320
321
315
316 317
382
322 323
324 325
331
326
327
328
329
340
333
334
335
336
339
338
330
332
341 342
337
-53-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
headstock breakdown 2
344
353
352
351
343
350
349
348
347
367
346
366
355
365
345
364
354
363
362
361
360
376
359
375
358
357
374
356
373
372
371
381
380
370
377
369
368
379
378
-54-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
headstock Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
P0756301
P0756302
P0756303
P0756304
P0756305
PSS128M
P0756307
HEADSTOCK HOUSING
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
P0756343
P0756344
PR97M
SPINDLE
AUTO DOWNFEED SHIFTING FORK
DOWEL PIN 10 X 20MM
QUILL
EXT RETAINING RING 75MM
O-RING 85 X 5.7
AUTO DOWNFEED SHIFTING SHAFT
AUTO DOWNFEED INDICATOR HUB
SET SCREW M8-1.25 X 25 PILOT
AUTOMATIC DOWNFEED DIAL
P0756346
P0756347
P51108
THRUST WASHER
THRUST BEARING 51108
NEEDLE ROLLER BEARING RNA49/32
SPRING HOUSING
P0756349
P0756350
PSTB003M STEEL BALL 6MM
P0756309
PSS06M
COMPRESSION SPRING 0.8 X 5 X 16
SET SCREW M8-1.25 X 16
P6006-2RS BALL BEARING 6006-2RS
P0756352
PCAP41M
P0756354
P0756355
P0756356
PR11M
CLAMP NUT
PSTB003M STEEL BALL 6MM
CAP SCREW M4-.7 X 14
DOWEL PIN 12 X 50MM
COMPRESSION SPRING
GEAR 32/20T
P0756312
P0756313
PSS128M
PN46M
COMPRESSION SPRING 0.8 X 7 X 12
AUTOMATIC DRIFT SHAFT
SET SCREW M8-1.25 X 25 PILOT
HEX NUT M8-1.25 THIN
PHLP HD SCR M6-1 X 12
COILED SPRING COVER PLATE
CAP SCREW M6-1 X 20
CURVED PLATE
EXT RETAINING RING 25MM
BEARING FLAT WASHER
PS14M
P0756358
P0756317
PCAP02M
P0756319
PRIV003M
P0756321
PS14M
P6205-2RS BALL BEARING 6205-2RS
PR26M
PR26M
INT RETAINING RING 52MM
INT RETAINING RING 52MM
STEEL FLUTED RIVET 2 X 4MM
INDEX RING
P6205-2RS BALL BEARING 6205-2RS
P0756363
P0756364
P0756365
P0756366
PR11M
WOODRUFF KEY 6 X 18
SHAFT
PHLP HD SCR M6-1 X 12
PLATE
P0756323
PCAP95M
P0756325
P0756326
P0756327
P0756328
P0756329
PS14M
WOODRUFF KEY 6 X 12
GEAR 22T
CAP SCREW M5-.8 X 30
FIREWALL PLATE
EXT RETAINING RING 25MM
EXT RETAINING RING 35MM
INT RETAINING RING 32MM
SLIDE PLATE
PR12M
PIN
PR29M
BRACKET
P6002-2RS BALL BEARING 6002-2RS
DRAIN PLUG 3/8" NPT SOCKET HEAD
PHLP HD SCR M6-1 X 12
CHIP GUARD ASSEMBLY
CONTROL PANEL COVER PLATE
STAR KNOB 5-PT M10-1.5 X 40
CAP SCREW M5-.8 X 8
SET SCREW M6-1 X 16 CONE
FLANGED COLLAR
PR29M
INT RETAINING RING 32MM
WORM
P0756372
P0756373
P0756374
P0756375
P0756376
P0756377
P0756378
P0756379
P0756380
PSS20M
P0756331
P0756332
P0756333
PCAP03M
PSS120M
P0756336
PCAP12M
PRP16M
P0756339
P0756340
P0756341
PS14M
NEEDLE ROLLER BEARING MF-2516
KEYED SPACER
GEAR 48/60T
KEYED SPACER
DOWEL PIN 6 X 8MM
DISC SPRING 45 X 24 X 1.75
CLAMP NUT
CAP SCREW M8-1.25 X 40
ROLL PIN 3 X 25
PLUNGER
QUILL COLLAR
SET SCREW M8-1.25 X 8
ROUND COVER PLATE W/ LUBE HOLE
QUILL COLLAR SHAFT
TORQUE LIMITER COVER PLATE
PHLP HD SCR M6-1 X 12
P0756382
-55-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Parts breakdown
Electrical Panel
405
404
402
403
406
401
425
407
408
409
424
423
431 430
428
429
426
427
Control Panel
Work Lamp
C2SS2-10B-10
C2SS2-10B-10
410
420
411
414
LX5W-A11N
419
C2SS2-10B-10
C2SS2-10B-10
413
422
418
412
421
419
418-1
LX5W-A11N
x1
x2
432
417
CP1-10R-01
-56-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Parts List
REF PART # DESCRIPTION
REF PART #
DESCRIPTION
401 P0756401 ROTARY SWITCH CANSEN LW26GS-20 4P
402 P0756402 CIRCUIT BREAKER HUILONG DZ451-63 D10 3P
403 P0756403 CIRCUIT BREAKER HUILONG DZ451-63 D1 2P
404 P0756404 CIRCUIT BREAKER HUILONG DZ451-63 C3 1P
405 P0756405 CIRCUIT BREAKER HUILONG DZ451-63 C1 1P
406 P0756405 CIRCUIT BREAKER HUILONG DZ451-63 C1 1P
407 P0756407 CONTACTOR TIANSHUI GSC-1201 24V
408 P0756407 CONTACTOR TIANSHUI GSC-1201 24V
409 P0756409 CONTACTOR TIANSHUI JZC3-40D 24V
410 P0756410 SELECTOR SWITCH ABB C2SS2-10B-10
411 P0756410 SELECTOR SWITCH ABB C2SS2-10B-10
412 P0756410 SELECTOR SWITCH ABB C2SS2-10B-10
413 P0756410 SELECTOR SWITCH ABB C2SS2-10B-10
414 P0756414 H/L ROTARY SWITCH CANSEN LW26-20 16P
417 P0756417 POWER LIGHT LA58-XD
418-1 P0756418-1 HALOGEN BULB 50W 24V BI-PIN
419
420
421
422
423
424
425
426
427
428
429
430
431
432
P0756419 LIMIT SWITCH LXW5-A11N
P0756420 E-STOP BUTTON 22MM ABB MCB-01
P0756421 GRN BUTTON ABB 800FP-F3 MCB-10(2)
P0756422 RED BUTTON ABB CP1-10R-01
P0756423 BRIDGE RECTIFIER KBP1010
P0756424 CONTROLLER E&E EX-30A1-B
P0756425 TRANSFORMER JBK5-100VATH
P0756426 GROUNDING BLOCK
P0756427 TERMINAL BAR 21P
P0756428 CONTROL PANEL WIRING HARNESS
P0756429 ELEC CLUTCH WIRING HARNESS
P0756430 PUMP WIRING HARNESS
P0756431 H/L SWITCH WIRING HARNESS
P0756432 CHIP GUARD LIMIT SWITCH
418 P0756418 HALOGEN WORK LAMP 24V 25W
-57-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Labels & cosmetics
506
503
502
501
504
509
510
508
507
511
509
505
512
513
509
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
501 P0756501
502 PLABEL-55
GLASSES FACE SHIELD LABEL 2"W X 3.3"H
ENTANGLEMENT LABEL 2"W X 3.3"H
508 P0756508 MODEL NUMBER LABEL
509 PLABEL-14 ELECTRICITY LABEL 1.4"W X 1.2"H
510 P0756510 GEARBOX OIL LEVEL NOTICE
511 P0756511 FLUID CAPACITIES LABEL
512 P0756512 MACHINE ID LABEL
503 PLABEL-12A READ MANUAL LABEL 2"W X 3.3"H
504 PLABEL-63
505 PLABEL-50
506 P0756506
507 P0756507
DISCONNECT POWER LABEL 2"W X 3.3"H
COOLANT HAZARD LABEL 2"W X 3.3"H
GEARBOX SPEEDS LABEL
513 PPAINT-1
GRIZZLY GREEN TOUCH-UP PAINT
CONTROL PANEL LABEL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
-58-
Model G0756 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email _________________________________________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Woodwork
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Shotgun News
____ Today’s Homeowner
____ Wood
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
____ 6-9
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTy & RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|