Instructions
LD Series Oil and Grease
Pump
3A1334F
EN
For dispensing non-corrosive and non-abrasive lubricants, oil, grease, and automatic
transmission fluids in stationary or mobile installations. Use with compressed air only. For
professional use only. Not for use with windshield washer fluid.
List of models, including Maximum Fluid Pressure:
•
Oil Pump Models: page 2
•
Grease Pump Models: page 3
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Related Translated Manuals
Manual Number Language
3A1339
3A1345
3A1350
3A1360
3A1365
3A1370
3A1375
Spanish
French
German
Russian
Chinese
Japanese
Korean
Download from Www.Somanuals.com. All Manuals Search And Download.
Grease Pump Models
Grease Pump Models
PN
Description
Max air pressure
Max Fluid Pressure
Fluid
Inlet
Fluid
Outlet
Air inlet
50:1 PUMPS
psi
Mpa
bar
psi
Mpa
bar
1/4"-18
Npt
Priming 1/4"-18
piston Npt
Priming 1/4"-19
piston BSPP
Priming 1/4"-19
piston BSPT
Priming 1/4"-18
piston Npt
Priming 1/4"-19
piston BSPP
Priming 1/4"-19
piston BSPT
Priming 1/4"-18
piston Npt
Priming 1/4"-19
piston BSPP
Priming 1/4"-19
piston BSPT
24G600 16kg (35lb)
150
150
150
150
150
150
150
150
150
1.03
10.3
10.3
10.3
10.3
10.3
10.3
10.3
10.3
10.3
7500
7500
7500
7500
7500
7500
7500
7500
7500
51.7
517
517
517
517
517
517
517
517
517
1/4"-19
BSPP
24G601 16kg (35lb)
24G602 16kg (35lb)
24G603 55kg (120lb)
24G604 55kg (120lb)
24G605 55kg (120lb)
24G606 180kg (400lb)
24G607 180kg (400lb)
24G608 180kg (400lb)
1.03
1.03
1.03
1.03
1.03
1.03
1.03
1.03
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.7
1/4"-19
BSPT
1/4"-18
Npt
1/4"-19
BSPP
1/4"-19
BSPT
1/4"-18
Npt
1/4"-19
BSPP
1/4"-19
BSPT
3A1334F
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and
warnings not covered in this section may appear throughout the body of this manual where applicable.
WARNING
SKIN INJECTION HAZARD
High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may
look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical
treatment.
• Do not point dispense valve at anyone or at any part of the body.
• Do not put your hand over the end of the dispense nozzle.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.
FIRE AND EXPLOSION HAZARD
When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be
aware that flammable fumes can ignite or explode. To help prevent fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources, such as cigarettes and portable electric lamps.
• Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
• Ground all equipment in the work area.
• Use only grounded hoses.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until
you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
4
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about
your material, request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical
reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or
property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents.
• Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier
for compatibility.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating area
of the equipment to help protect you from serious injury, including eye injury, hearing loss, inhalation of
toxic fumes, and burns. This equipment includes but is not limited to:
• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
3A1334F
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
NOTE: Reference letters and numbers in parentheses in the text refer to callouts in the figures and drawings.
•
•
•
Air and fluid hoses: Use only electrically conductive
hoses.
Grounding
Air compressor: Follow manufacturer’s recommen-
dations.
Dispensing valve: Ground through connection to a
properly grounded fluid hose and pump.
To reduce the risk of static sparking, ground the pump
and all other components used or located in the
dispensing area. Check your local electrical code for
detailed instructions for your area and type of
equipment.
•
•
Object being dispensed to: Follow your local code.
Solvent pails used when flushing: Follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the pail
on a nonconductive surface, such as paper or card-
board, which interrupts the grounding continuity.
Ground all equipment:
•
Pump: Use a ground wire and clamp as shown in
•
To maintain grounding continuity when flushing or
relieving pressure, hold a metal part of the dispens-
ing valve firmly to the side of a grounded metal pail,
then trigger the dispense valve.
a. Remove the ground screw (Z) and insert
through the eye of the ring terminal at end of
ground wire (Y).
b. Fasten the ground screw back onto the pump
and tighten securely.
NOTE: To order a ground wire and clamp, order Graco
Part No. 222011.
Y
Z
ti16123
FIG. 1
6
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Typical Installation
The typical installation shown in FIG. 2 is only an installation guide. It is not an actual system design. Contact your
Graco Distributor for assistance in designing a system to suit your needs.
Stationary Mountings
Recommended
air line
C
configuration
to reduce
moisture in pump
B
E
F
M
F
A
J
G
H
D
K
N
L
ti16120
FIG. 2
A
B
C
D
E
F
Fluid outlet line (flexible connection required)
Pump
Ground wire
Pump runaway valve
Air lubricator
Bleed-type master air valve (required)
• NPT - Part No. 110223
• BSP - Part No. 125272
Air regulator (self-relieving regulator required)
• NPT - Part No. 24H420
• BSP - Part No. 24H419
Air filter
G
H
J
Main air line
K
L
M
N
Bung adapter - Part No. 24F918
Fluid inlet line (flexible connection required)
Air inlet line (flexible connection required)
Wall mount bracket - Part No. 24F910
3A1334F
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Pump Mounting
Installation Guidelines
1. Install bung adapter (K) into bung mount/bracket/or
drum cover.
Reference letters found in the following instructions,
2. Install pump (B) into bung adapter (K).
•
•
A ball valve must be installed upstream of the regu-
lator (G).
B
The fluid outlet line (A), fluid inlet line (L) and air
inlet line (M) must be flexible (such as a hose).
NOTE: To prevent damage to the pump, remove sedi-
ment from the bottom of the container before installing a
pump on an existing container.
A
K
aa
The maximum working pressure of each pump in
your system may not be the same. To reduce the risk
of over-pressurizing any part of your system, which
may result in component rupture, fire or explosion
and cause serious bodily injury, be sure you know
the maximum working pressure rating of each pump
and its connected components.
FIG. 3
Installing Outlet Hose (FIG. 3)
1. Connect the swivel adapter (aa) to the pump fluid
outlet. Tighten securely and torque as recom-
mended below:
•
•
Never exceed the maximum working pressure of
the lowest rated component connected to a partic-
ular pump.
•
•
For NPT models: 1 to 1-1/2 turns past hand
tight.
For BSPT models: 1-1/2 to 2 turns past hand
tight.
Be sure you know the maximum working pressure
of each component.
•
•
Do not exceed the maximum pump cycle rate.
2. Connect the fluid hose (A) to the swivel adapter
(aa).
Regulate air pressure to prevent over pressuriza-
tion at fluid section of the pump.
3. Connect a suitable dispensing valve or extra hose to
the 6-ft hose.
•
Regulate air pressure to the pump so that no fluid
line component or accessory is over pressurized.
Stationary Mounting Layout
Plan the layout for easy operator access to the pump air
controls, sufficient room to change drums and a secure
platform.
8
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Air Line and Accessories
NOTE: Install the air line accessories in the order shown
NOTICE
Do not hang the air accessories directly on the air
inlet. Mount them on brackets. Always use a flexible
hose between all connections. The air inlet is not
strong enough to support accessories and may cause
one or more to break.
•
•
Use thread sealant on all male threads except
swivel connections.
Install a pump runaway valve (D) to shut off the air
to the pump if the pump accelerates beyond the
pre-adjusted setting. A pump that runs too fast can
be seriously damaged.
•
•
Install the air regulator (G) to control pump speed
and pressure.
For NPT models order Graco Part No. 24H420 or for
BSP models order Graco Part No. 24H419.
Install a bleed-type master air valve (F) upstream
from the pump air regulator (G) but within easy
reach of the pump.
For NPT models order Graco Part No. 110223 or for
BSP models order Graco Part No. 125272.
•
On the main air supply line from the compressor,
install an air line filter (H) to remove harmful dirt and
contaminants from the compressor air supply.
Follow Plate - Grease Models Only
For grease models only a follow plate is required for
plate installation instructions.
3A1334F
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Thermal Induced Pressure
Relief (Oil pumps only)
a
THERMAL EXPANSION HAZARD
Fluids subjected to heat in confined spaces, including
hoses, can create a rise in pressure due to the
thermal expansion. Over-pressurization can result in
equipment rupture and serious injury.
Oil pumps have a built-in, thermal induced, pressure
will automatically bleed excess thermal induced
system pressure through the pump and back to the
oil reservoir:
b
FIG. 4 a = Pump cylinder relief passage
•
Always use a relieving air pressure regulator to
allow the pump/motor to run backwards. The regu-
lator bleeds excess air pressure.
b = Inlet check relief passage
Thermal Relief Theory of Operation
The pump operation is similar to most double acting
reciprocating pumps. The pump only comes to a com-
plete stop on the up stroke. The pump will stroke
through on the down stroke due to the inlet check relief
passage.
•
•
There should not be any obstructions between air
inlet of pump and regulator.
There should not be any obstructions between the
downstream plumbing and pump outlet such as
closed ball valves or check valves.
Excess pressure due to downstream thermal expansion
causes the air motor/pump to run backwards (down-
ward). Fluid pressure is relieved through the inlet check
relief passage as the pump piston moves downward. Air
pressure is simultaneously relieved through the air inlet
passage. The pump piston moves downward exposing
the pump cylinder relief passage at the bottom of the
stroke. Additional excess pressure is then relieved
through both the inlet check relief passage and the
pump cylinder relief passage.
•
There should not be any obstructions between the
pump inlet and fluid container such as closed ball
valves or check valves.
•
•
•
Only use Graco designed suction tubes for in-drum
or in-tank applications.
Only use Graco designed suction tubes with a
built-in relief device for wall mount applications.
Pressure is relieved at the pump through the pump inlet
relief passage. The pump will not change over on the
bottom of the stroke as a result of relieving excess pres-
sure due to the positioning of the pump cylinder groove
with respect to the air motor pilot valve.
Always use an inlet screen to prevent debris from
plugging relief passages from entering the pump.
- Do not operate the pump with out an inlet screen.
NOTE:
•
Periodically inspect the inlet screen for plugging.
Graco recommends inspecting the inlet screen
every time the container is changed out.
•
The air supply does not have to be turned off to
enable thermal relief activation.
•
The Thermal Induced Pressure Relief design fea-
ture of the pump will cause the pump to dive on the
downstroke when a dispensing valve is closed.
10
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Install only one pump per delivery system. Do not use
the pumps in a parallel pump installation.
Start-up
Determining Output Pressure Using the Air
Regulator
Loss of pump prime can occur if all the following events
occur in sequence:
To determine the fluid output pressure using the air reg-
ulator reading, multiply the ratio of the pump by the air
pressure shown on the regulator.
1. A thermal relief event occurs.
2. The air supply valve is closed.
3. A dispense valve located at an elevation higher than
the tank level, is open.
For example a 3:1 ratio oil pump:
3:1 ratio x 100 psi air = 300 psi fluid outlet
To prevent loss of prime, ensure the air supply valve is
turned on before attempting to dispense fluid.
A 3:1 pump is capable of 5:1 on the downstroke and will
develop 5:1 pressures under normal operation.
Pressure Relief Procedure
A grease pump has a ratio of 50:1. However it is capable
of reaching a stall pressure equal to 60 times the air
input pressure. To calculate the fluid output pressure
using the air regulator reading, multiply the regulator
gauge by 60.
The equipment stays pressurized until pressure is
manually relieved. To reduce the risk of serious injury
from pressurized fluid, fluid from the valve, or splash-
ing fluid, follow this procedure whenever you:
For example:
140 psi air x 60 = 8400 psi fluid output
0.97 MPa air x 60 = 58.2 MPa
99.7 bar x 60 = 582 bar
•
•
•
are instructed to relieve pressure
stop dispensing
check, clean, or service any system equip-
ment
Regulate air to the pump so that no air line or fluid line
component or accessory is over pressurized.
•
install or clean dispensing devices.
Priming the pump
1. Close the pump’s bleed-type master air valve.
1. Close the air regulators and bleed-type master air
valves to all but one pump.
2. Close the pump air regulator and disconnect the air
supply hose.
2. Open the master air valve from the compressor.
3. Open the dispensing valve and dispense fluid into a
waste bucket/container until pressure is fully
relieved.
3. For the pump that is connected, trigger the dispens-
ing valve into a grounded metal waste container
making firm, metal-to-metal contact between the
container and the valve.
If you suspect that the dispensing valve is clogged, or
that pressure has not been fully relieved after following
the steps above, very slowly loosen the dispensing
valve coupler or hose end coupling to relieve pressure
gradually, then loosen completely.
4. Slowly open the bleed-type master air valve and
open the pump air regulator just until the pump is
running. When the pump is primed and all air has
been pushed out of the lines, release the trigger.
5. If you have more than one pump, repeat this pro-
cess for each pump in your system.
NOTE: When the pump is primed and has sufficient
air supplied to it, it starts when the dispensing valve
is open and shuts off when closed.
3A1334F
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Changing Grease Drum and Installing
Follow Plate (grease models only)
6. The thermal relief feature of this oil pump can
increase the amount of time needed to fully prime
the pump when compared to pumps without a ther-
mal relief feature. To minimize this effect, prime the
pump before connecting it to an already primed dis-
tribution system.
NOTICE
2. Remove drum cover by loosening thumb screws (a)
(FIG. 5).
Never allow the pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a high
speed, possibly damaging itself. If your pump acceler-
ates quickly, or is running too fast, stop it immediately
and check the fluid supply. If the supply container is
empty and air has been pumped into the lines, prime
the pump and lines with fluid, or flush it and leave it
filled with a compatible solvent. Be sure to eliminate
all air from the fluid system.
a
NOTE: A pump runaway valve can be installed on the
air line to automatically shut off the pump if it starts to
run too fast.
FIG. 5
7. Read and follow the instructions supplied with each
component in your system.
3. Remove pump and cover from drum and place on a
clean paper, cardboard, or clean shop rags. DO
NOT PLACE ON SHOP FLOOR.
8. When shutting off the system and before checking
or servicing, relieve pressure following pressure
4. If this is an existing installation, reach into drum and
pull on follow plate ring (b) to remove follow plate
(FIG. 6). Place follow plate on a clean paper, card-
board or clean shop rags. DO NOT PLACE ON
SHOP FLOOR.
Remove drum and install new one.
b
FIG. 6
12
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5. Examine follow plate to make sure rubber grommet
(c) is in place in center of the plate (FIG. 7).
7. Insert pump drop tube through center of rubber
grommet in follow plate (FIG. 9).
Se
c
FIG. 7
6. Set follow plate on top of fresh grease (FIG. 8).
Remove air by pushing on the follow plate until the
grease level is flush with the opening in the middle
of the follow plate (d).
FIG. 9
8. Tighten thumb screws (a) to secure cover to drum.
d
a
FIG. 10
FIG. 8
9. For the pump that is connected, trigger the dispens-
ing valve into a grounded metal waste container
making firm, metal-to-metal contact between the
container and the valve.
10. Slowly open the bleed-type master air valve and
open the pump air regulator just until the pump is
running. When the pump is primed and all air has
been pushed out of the lines, release the trigger.
3A1334F
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair
Repair
Replacing Pilot Valves
Reference letters shown in the following instructions
1. Stop pump at the middle of its stroke.
3. Disconnect the air line (M).
4. Use a 10 mm socket wrench to remove the old pilot
valve (20).
5. Lubricate o-rings and install the new pilot valve (20).
Torque to 95-105 in-lb (11-12 N.m).
14
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Parts
3:1 Oil Pump Models: 24G576 - 24G587: 5:1 Oil Pump Models: 24G588 - 24G599
Ref Part No Description
Qty
Ref Part No Description
Qty
1
16G243◆ LABEL, safety, warning, multiple
1
8
1
1
40 ▲
43
2
116343 SCREW, ground
SCREW
✿
SCREW, M6 x 25 mm
3
3
50
24F918 ADAPTER, bung, LD pump
4
SCREW M6 x 22 mm
5
51
16G121★ STRAINER
5
O-RING, air piston
O-RING
1
✠
✠
✠
✠
✠
TUBE, PVC, LD pump (models
16F878
6
1
1
1
1
1
1
1
1
1
24G579, 24G591)
7
O-RING
1
TUBE, PVC, LD pump (models
24G580, 24G592)
TUBE, PVC, LD pump (models
24G581, 24G593)
TUBE, metal, LD pump (models
24G582, 24G594)
TUBE, metal, LD pump (models
24G583, 24G595)
16F948
52‡
53‡
8
O-RING,
1
9
SEAL, u-cup
PIN, spring
BALL, steel
BALL, steel
1
16F949
10
11
12
1
16F886
★
1
1
16F950
✓
O-RING, (models 24G576 - 24G578)
O-RING (models 24G588 - 24G590)
O-RING
1
1
1
1
1
3
1
1
2
1
1
13
TUBE, metal, LD pump (models
24G584, 24G596)
✓
16F951
14
15
16
17
18
19
20
21
22
✓
TUBE, metal, LD pump (models
24G585, 24G597)
16F885
✓★
O-RING
SCREW
TUBE, metal, LD pump (models
243G586, 24G598)
TUBE, metal, LD pump (models
24G587, 24G599)
54‡
55
16F962
O-RING
✠
16F963
1
1
BOLT M8 X 25
WASHER, M8 (not shown)
VALVE, pilot
✠
O-Ring (not shown)
◆ ✖
PISTON, air, plastic
BEARING, delrin
▲ Replacement Danger and Warning labels, tags, and
cards are available at no cost.
15M182
❖ †✿ ◆
15M213 MUFFLER, 3/8
23
24
SEAL, air valve, manifold (not shown)
1
‡ Packaged separately with universal pump.
1
1
2
1
1
1
✠
✓
★
Included in kit 24H853
112933 MUFFLER, quiet (optional)
Included in kits 24K293 - 3:1; 24H855 - 5:1
Included in kits 24H611 (npt), 24J430 (bspp) 24J431
(bspt)
25
26
27
28
GASKET, cover, small
✠
COVER, bottom, machining
CYLINDER air, machined
❖
†
Included in kit 24H798
★
HOUSING, intake valve, machined
FLANGE, oil, machined
ROD, displacement
Included in kit 24H851
29
30
31
1
1
1
Included in kit 24H848 (npt), 24H849 (bspp), 24H850
(bspt)
✿
Included in kit 24J757 (npt), 24J758 (bspp), 24J759
(bspt)
GUIDE, air
◆
✖
32
33
34
35
36
37
CYLINDER, fluid
1
1
1
1
1
1
Included in kit 24H749
PISTON, pump, 3:1, machining
HOLDER, ball
★
✿
SPRING, compression
SPRING, compression
HOUSING, manifold, machined
38
VALVE, air, small
1
1
16F541 LABEL, identification, lD 3:1
39 ▲
3A1334F
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Throat and Piston Seal Replacement Kit -
24H853 (FIG. 12)
Related Oil Pump Kits
NOTE: When servicing the throat and piston seals, it is
recommended to also replace seals in the pump lower.
Order repair kit: 24K293 for 3:1 pumps or 24H855 for
5:1 pumps. Instructions related to this kits are included
in instruction manual 3A1494 (included with the kit).
Kit No. Description
Qty
KIT, repair, intake valve, npt,
24H611
24J430
24J431
1
1
1
includes 11, 15, 28, 35, 51
KIT, repair, intake valve, bspp,
includes 11, 15, 28, 35, 51
KIT, repair, intake valve, bspt,
includes 11, 15, 28, 35, 51
Ref. Description
Qty.
5
6
7
8
O-RING, air piston
O-RING
O-RING
O-RING, wiper
SEAL, u-cup
O-RING
GASKET, cover, small
O-RING (not shown)
1
1
1
1
1
3
2
1
O-Ring Replacement Kit - 24K293 for 3:1
pumps; 24H855 for 5:1 pumps (FIG. 11)
NOTE: When replacing seals in the pump lower also
service the throat and piston seals. Order repair kit
24H853. Instructions related to this kit are included in
instruction manual 3A1494 (included with the kit).
9
17
25
55
Ref. Description
Qty.
7
13
14
15
O-RING
O-RING
O-RING
1
1
1
5
9
13
8
14
15
FIG. 11
25
17
6
FIG. 12
16
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Kits
Page 21
1
20
27
6
18
19
40
39
30
34
36
21
10
5
3 3
17
12
31
5
4
1
52, 53
or 54,
33
6
26
13
14
Page
7
20
22
2
32
11
9
8
35
11
4
3
15
51
29
28
2
1
Torque to 95-105 in lbs (10.7 - 11.9 N•m)
Torque to 20 - 25 ft lbs (27- 34 N•m)
Torque to 60 - 70 in lbs (6.8 - 7.9 N•m)
Torque to 25 - 35 in lbs (2.8 - 3.9 N•m)
4 2
2
50
3
4
5
6
Torque to 110 - 120 in lbs (12.4 - 13.6 N•m)
Torque to 80 - 90 in lbs (9.0 - 10.2 N•m)
Lips face down
11
3A1334F
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
50:1 Grease Pump Models: 24G600 - 24G608
Ref Part No. Description
Qty
1
Ref Part No. Description
Qty
1
34
35
36
37
38
39
40
ROD, priming
2
116343 SCREW, ground
SCREW
PISTON, shovel, 50:1
CYLINDER, spacer
NUT, retainer
1
3
3
1
4
SCREW, M6 X 22 mm
5
1
+
5
O-RING, air piston
O-RING (not shown)
O-RING
1
+
WASHER, 30 OD
HOUSING, manifold, machined
VALVE, air, small
1
6
1
+
1
7
10
3
+
✿◆
1
8
PIN, straight, slotted, 2.5x16
SCREW
+@
41 ▲ 1GH013 LABEL, identification, LD 50:1
42 ▲ 16G243 LABEL, safety, warning, multiple
1
9
1
1
10
11
12
13
14
15
O-RING
1
@
+
43
✿
SCREW, M6 x 25 mm
8
SEAL, u-cup
1
O-RING
3
+
▲ Replacement Danger and Warning labels, tags, and
WASHER,M8
1
cards are available at no cost.
COVER, bottom, machining
PISTON, air, plastic
1
1
+
@
★
Included in kit 24H854
15M182
❖ † ✿◆
16
17
SEAL, air valve, manifold
1
Included in kits 24H856
Included in kits 24H611 (npt), 24J430 (bspp) 24J431
(bspt)
15M213 MUFFLER, 3/8
1
1
2
2
2
1
1
1
1
1
1
1
1
1
2
1
1
1
112933 MUFFLER, quiet (optional)
❖
†
Included in kit 24H798
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
GASKET, cover, small
NUT, hex
+
Included in kit 24H851
Included in kit 24H848 (npt), 24H849 (bspp), 24H850
(bspt)
Included in kit 24J757 (npt), 24J758 (bspp), 24J759
(bspt)
✿
◆ ✖
VALVE, pilot
◆
✖
CYLINDER, air, machined
FLANGE, bottom cover, grease,
ROD, piston, 50:1
Included in kit 24H749
SEAL, piston
@
ROD, displacement, 50:1
CYLINDER, HP 50:1
24J380 KIT, cylinder, shovel
SEAL, intake
@
RETAINER, seal, al
GASKET
+@
BEARING, throat
ROD, connection
GUIDE, air
18
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Related Grease Pump Kits
Throat and Piston Seal Replacement Kit -
O-Ring and Seal Replacement Kit - 24H856
(FIG. 14)
Instructions related to this kit are included in instruction
manual 3A1495 (included with the kit).
Instructions related to this kit are included in instruction
manual 3A1495 (included with the kit).
Ref. Description
Qty.
Ref. Description
Qty.
5
6
7
8
11
12
18
30
37
O-RING, air piston
O-RING
O-RING
PIN, slotted, straight
SEAL, u-cup
O-RING
GASKET, cover, small
GASKET
1
1
1
3
1
3
2
1
1
8
PIN, slotted, straight
O-RING
SEAL, piston
SEAL, intake
GASKET
3
1
1
1
2
10
24
28
30
30
NUT, retainer
18
11
24
7
8
6
28
8
10
12
FIG. 14
37
5
30
FIG. 13
3A1334F
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
1
Torque to 95-105 in lbs (10.7 - 11.9 N•m)
Torque to 60 - 70 in lbs (6.8 - 7.9 N•m)
3
1
20
7
Torque to 70 - 80 in lbs (7.9 - 9.0 N•m)
Torque to 45 - 55 ft lbs (61 - 75 N•m)
Torque to 30 - 40 in lbs (3.4 - 4.5 N•m)
Torque to 30 - 35 in lbs (3.4 - 4.0 N•m)
Lips face down
8
21
41
9
30
8
36
10
11
30
42
13
8
26
19
7
5
15
8
38
10
37
24
11
11
23
31
28
10
29 8
3
3
25
8
12
6
33
34
9
20
1
14
7
35
22
3 4
19 7
8
27
32
9 2
20
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Air Valve Seal Kit - 24H851
Oil or Grease Pump Air Valve
Repair and Replacement Kits
Instructions related to the following kits are included in
instruction manual 3A1496 (included with the kit).
Ref.
Description
Qty.
Oil Grease
23
16
SEAL, air valve, manifold
O-RING, 018 buna
1
2
2
2
381
382
383
381
382
383
SEAL, u-cup, bevel lip
SCREW, M3, thread forming
Replace Seals or Rebuild Air Valve Kits
Air Valve Repair Kit - 24H798, Air Valve Seal Kit -
24H851 and Air Valve End Cap - 24H852.
382
1
Air Valve Repair Kit - 24H798
381
383
Ref.
Description
Qty.
Oil Grease
2
382
23
16
SEAL, air valve, manifold
O-RING, 018 buna
1
2
2
2
1
1
1
1
1
1
23/16
381
382
383
386
387
388
389
390
391
381
382
383
386
387
388
389
390
391
SEAL, u-cup, bevel lip
SCREW, M3, thread forming
PISTON, air valve
Lips face down
Lips face up
1
2
381
ROLLER, assembly, detent
PLATE, air valve
FIG. 16
SPRING, detent, small
CUP, air valve, small
CAM, detent, small
Air Valve End Cap Kit - 24H852
Ref. Description
381 O-RING, 018 buna
384 PLUG, air valve
385 RING, snap
Qty.
2
2
2
Lips face down
Lips face up
1
2
381
391
1
382
381
384
386
390
388
387
2
385
389
FIG. 17
382
381
383
23/16
FIG. 15
3A1334F
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Air Valve Replacement Kit - 24H848 (npt),
24H849 (bspp), 24H850 (bspt) (FIG. 18)
Pilot Valve Replacement Kit - 24H749
This kit only includes the pilot valves (20). If you
also are repairing/replacing the air valve (38/40) and
air valve seal (23/16) order the Air Motor Service Kit -
24J757 (npt), 24J758 (bspp) or 24J759 (bspt).
38/40
Ref.
20
Description
VALVE, pilot
Qty.
2
43
Air Motor Service Kit - 24J757 (npt), 24J758
(bspp), 24J759 (bspt) (FIG. 19)
23/16
I
FIG. 18
38/40
Ref.
Description
SEAL, air valve
Qty.
Oil
23
38
43
Grease
16
20
1
1
4
40
VALVE, air, small
SCREW, M6 x 25
43
23/16
FIG. 19
Ref.
Description
VALVE, pilot
SEAL, air valve
VALVE, air, small
Qty.
Oil
Grease
2
1
1
20
23
40
20
16
40
22
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
NOTE: Check all other possible problems and solutions
before disassembling the pump. Before you troubleshoot
problems using the table below, relieve the pressure
and disconnect the pump fluid line. If the pump starts
when the air is turned on again, the fluid line, dispensing
valve, etc. clogged.
Oil Models
Problem
Cause
Solution
Crack a fitting at the outlet of the
pump to allow a slow leak to purge
any air in the pump. Repeat start up
Pump is not fully primed
Oil leakage
Check connection and tighten.
The piston valve is not seating prop-
erly or the piston o-ring is damaged
Pump runs but no fluid output
Check and replace parts as needed.
Exhausted fluid supply
Refill and reprime.
Clear the filter
The pump inlet filter is blocked
The suction tube (hose) has an air
leak
Check the connection and tighten as
needed.
Service pilot valve.
Damaged pilot valve
Lower air pressure to prevent reoc-
currence.
Replace air valve.
Damaged main air valve
Lower air pressure to prevent reoc-
cur an ce.
Pump fails to operate or stops
Inadequate air supply pressure or
restricted air lines.
Increase air supply; clear.
Open valve if closed. Clear clog if
necessary.
Closed or clogged dispensing valve
Clogged fluid lines, hose valves, etc. Clear clogs.
Damaged air motor
Service air motor.
Exhausted fluid supply
Refill and reprime.
Replace valve gasket.
Erratic or accelerated operation
Damaged valve gasket
Lower air pressure to prevent reoc-
currence.
3A1334F
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Cause
Solution
Replace gasket.
Gasket is leaking
Lower air pressure to prevent reoc-
currence.
Intermittent air leakage coming from
behind the air manifold. Pump con-
tinues to function normally.
Clear obstruction.
Thermal relief inlet check relief pas-
sage in inlet housing is plugged
Replace inlet filter.
Worn or damaged piston o-ring or
valve cup.
Service air motor / valve
Replace valve gasket.
Continuous air exhaust
Damaged valve gasket
Lower air pressure to prevent reoc-
currence.
Held open or worn intake valve
Clear; service.
Clear; service.
Held open or worn pump piston
packings
The muffler is partially blocked
The inlet filter is partially blocked
Clear muffler.
Clear the filter.
Pump operates but output is low
Inadequate air supply pressure or
restricted air lines
Increase air supply; clear restric-
tions.
Partially closed or clogged pilot
valves
Open valves. Clear clog as neces-
sary.
Partially clogged fluid line, hose,
valves, etc.
Clear clog as necessary.
Oil leakage through air exhausts
Throat seal is damaged
Replace throat seal (u-cup).
24
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Grease Models
Pump fails to operate
Inadequate air supply pressure or
restricted air lines
Increase air supply and/or clear
restriction.
Closed or clogged pump valves
Open and/or clean.
Clogged fluid line, hose, valve, or
other accessory
Relieve pressure.
Clear obstruction.
Damaged air motor
Assess damage, and service air
motor.
Exhausted fluid supply
Refill and reprime or flush.
Continuous air exhaust
Erratic pump operation
Worn or damaged piston o-ring or
valve cup
Assess wear or damage, and service
air motor.
Exhausted fluid supply
Worn pump seals
Refill and reprime or flush.
Replace.
Damaged shovel tube
Damaged check seat
Replace.
Replace pump piston or shovel rod
(or other damaged part).
Errataic or accelerated pump speed Exhausted fluid supply
Fluid too heavy for pump priming
Refill and reprime of flush.
Use inductor or follow plate.
Replace valve gasket.
Damaged valve gasket
Lower air pressure to prevent reoc-
currence.
Worn piston seal
Replace.
Damaged upper check seat
Worn fluid intake seal
Damaged lower check seat
Replace pump piston.
Replace.
Replace shovel rod.
Inadequate air supply pressure or
restricted air lines
Increase air supply and/or clear
restriction.
Pump operates but output is low
Partially closed or clogged pump
valves
Open and/or clean.
Air pockets in the grease inlet
Eliminate the air pockets.
Partially clogged fluid line, hose,
valve, or other accessory
Relieve pressure.
Clear obstruction.
Worn seals
Replace.
Replace.
Grease leaking from muffler
Worn throat seal
3A1334F
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
3:1 or 5:1 Oil Models
Maximum fluid working pressure
750 psi (51.7 bar, 5.17 MPa)
Fluid pressure ratio
3:1 or 5:1
Suction lift (feet of oil)
Air operation range
10
20 to 150 psi (1.37 to 10.3 bar; 0.137 to 1.03 MPa)
<125 psi (8.6 bar, 0.86 MPa)
Recommended air pressure for optimum
pump life
Air consumption (at 100 psi)
Cycles per gallon/(liter)
See Performance Curves, page 29
3:1 - 29 cycles per gallon (7 cycles per liter); 5:1 - 37 cycles per gallon)
(10 cycles per liter)
Maximum recommended pump speed
3:1 - 120 cycles per minute; 5:1 - 180 cycles per minutes
Recommended speed for optimum pump 75 cycles per minute and lower
life
3:1 - 2.6 gallons per minute (9.8 liters per minute); 5:1 - 2 gallons per
minute (7.6 liters per minute)
Wetted parts
zinc plated carbon, steel, aluminum, nitrile, polyurethane, nickel plated
aluminum
Sound pressure level†*
Sound power level‡*
Performance curve
Approximate weight
Dimensions
72.9 dB(a)
82.0 dB(a)
See charts page 28
3:1 - 7 pounds (3.2 kg); 5:1 - 7.7 pounds (3.5 kg)
See page 30
† Calculated at a distance of 1 meter from measurements taken per ISO 9614-2 @ 100 psi air pressure (6.89 bar,
0.68 MPa) and 20 cycles per minutes.
‡ Measured per ISO 9614-2 at 100 psi air pressure (6.89 bar, 0.68 MPa) and 20 cycles per minute.
* Muffler 112933 can be ordered separately for reduced sound levels.
26
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Dimensions
O
L
*Multi down tube is angle
cut to the desired length
as required
Model
(Overall Length)
inches (mm)
inches (mm)
Universal Pump
Only
6.9 (175)
16 (406)
3/8” (10 mm)
minimum
Multi*
Drum
Tote
42.4 (1076)
35.7 (907)
42.8 (1087)
51.5 (1307)
44.8 (1138)
51.9 (1318)
Multi/Drum/Tote
a
Universal Pump
a
O
d
d
e
e
c
c
L
b
O
a = 1/4 inch air inlet
b = 1 inch fluid inlet
L
c = 2 inch npt bung adapter
d = ground screw
e = 1/2 inch fluid outlet - opposite of d
b
3A1334F
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Performance Curve
3:1 Oil Models
3:1 Performance Curve
Tested with ISO 46 Hyd Oil
(ꢏꢅꢖꢗꢀꢃꢃꢀꢁꢂꢃ)ꢂꢖꢈꢈꢐꢂꢖꢈ*
ꢔꢕꢉꢅꢖꢈꢃꢓꢖꢂꢃꢋꢁꢏꢐꢗꢖ
ꢙꢚꢛꢛꢃꢓꢈꢁ
58
116
174
232
ꢃꢃꢇꢜ !ꢃ"#ꢂꢌ
40
(1.1)
400
ꢙ$ꢛꢃꢓꢈꢁ
(27.6)
ꢘ
ꢀ
ꢃꢃꢇ% &ꢃ"#ꢂꢌ
30
ꢀ
(.8)
300
(20.7)
ꢙ%ꢛꢃꢓꢈꢁ
ꢔ
ꢃꢃꢇ' &ꢃ"#ꢂꢌ
ꢘ
200
ꢘ
20
(.6)
(13.8)
ꢔ
ꢔ
10
(.3)
100
(6.9)
+ꢖꢉꢆꢋꢋꢖꢏꢑꢖꢑꢃ,ꢓꢖꢂ#ꢗꢁꢏꢒꢃ+#ꢏꢒꢖ
0
0
0
1
(3.8)
2
(7.6)
3
4
5
6
7
8
9
(11.4)
(15.1)
(18.9)
(22.7)
(26.5)
(30.3)
(34.1)
ꢄꢅꢐꢁꢑꢃꢄꢅꢆ ꢃꢇꢒꢓꢋꢌ
ꢇꢅꢓꢋꢌ
5:1 Oil Models
5:1 Performance Curve
(ꢏꢅꢖꢗꢀꢃꢃꢀꢁꢂꢃ)ꢂꢖꢈꢈꢐꢂꢖꢈ*
Tested with ISO 46 Hyd Oil
ꢙꢚꢛꢛꢃꢓꢈꢁ
ꢔꢕꢉꢅꢖꢈꢃꢓꢖꢂꢃꢋꢁꢏꢐꢗꢖ
ꢃꢃꢇꢜ !ꢃ"#ꢂꢌ
74
148
222
ꢙ$ꢛꢃꢓꢈꢁ
ꢘ
600
ꢃꢃꢇ% &ꢃ"#ꢂꢌ
(41.4)
40
(1.1)
500
(34.5)
ꢙ%ꢛꢃꢓꢈꢁ
ꢔ
ꢀ
ꢃꢃꢇ' &ꢃ"#ꢂꢌ
ꢀ
400
(27.6)
30
(.8)
300
ꢘ
ꢘ
(20.7)
20
(.6)
200
(13.8)
ꢔ
ꢔ
10
(.3)
100
(6.9)
+ꢖꢉꢆꢋꢋꢖꢏꢑꢖꢑꢃ,ꢓꢖꢂ#ꢗꢁꢏꢒꢃ+#ꢏꢒꢖ
0
0
0
1
2
(7.6)
3
4
5
6
7
(3.84)
(11.4)
(15.1)
(18.9)
(26.5)
(26.5)
ꢄꢅꢐꢁꢑꢃꢄꢅꢆ ꢃꢇꢒꢓꢋꢌ
ꢇꢅꢓꢋꢌ
28
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
50:1 Grease Models
Maximum working pressure
Fluid pressure ratio
7500 psi (517 bar, 51.7 MPa)
50:1
Air operation range
20 to 150 psi (1.37 to 10.3 bar; 0.137 to 1.03 MPa)
See Performance Curve, page 30
47 cycle per pound (103 cycle per kg)
120 cycles per minute
Air consumption (at 100 psi)
Pump cycles per pound (cycles per kg)
Maximum recommended pump speed
Recommended speed for optimum pump life 60 cycles per minute or lower flow rate; 1.3 pounds per minute
(0.6 kg per minute)
Wetted parts
steel, brass, nitrile rubber, polyurethane, UHMWPE, acetal
Sound pressure level†*
Sound power level‡*
Performance curve
Approximate weight
72.9 dB(a)
82.0 dB(a)
See chart page 30
35 pound drum - 11.2 pounds (5.1 kg); 120 pound drum - 15.0
pounds (6.8 kg); 400 pound drum - 170.0 pounds (7.7 kg)
Dimensions
See illustration below
† Calculated at a distance of 1 meter from measurements taken per ISO 9614-2 @ 100 psi air pressure (6.89 bar,
0.68 MPa) and 20 cycles per minutes.
‡ Measured per ISO 9614-2 at 100 psi air pressure (6.89 bar, 0.68 MPa) and 20 cycles per minute.
* Muffler 112933 can be ordered separately for reduced sound levels.
Performance Curve
Grease Models
50:1 Performance Curve
Tested with ISO 46 Hyd Oil
(ꢏꢅꢖꢗꢀꢃꢃꢀꢁꢂꢃ)ꢂꢖꢈꢈꢐꢂꢖꢈ*
ꢙꢚꢛꢛꢃꢓꢈꢁ
ꢃꢃꢇꢜ !ꢃ"#ꢂꢌ
ꢔꢕꢉꢅꢖꢈꢃꢓꢖꢂꢃꢋꢁꢏꢐꢗꢖ
47
94
141
8000
(551.6)
ꢙ$ꢛꢃꢓꢈꢁ
ꢘ
ꢔ
ꢃꢃꢇ% &ꢃ"#ꢂꢌ
7000
(482.6)
50
(1.4)
ꢙ%ꢛꢃꢓꢈꢁ
ꢃꢃꢇ' &ꢃ"#ꢂꢌ
6000
(413.7)
40
(1.1)
5000
(344.7)
ꢀ
ꢘ
ꢔ
ꢀ
30
(.8)
4000
(275.8)
ꢘ
ꢔ
3000
(206.8)
20
(.6)
2000
(137.9)
10
(.3)
1000
(68.9)
+ꢖꢉꢆꢋꢋꢖꢏꢑꢖꢑꢃ,ꢓꢖꢂ#ꢗꢁꢏꢒꢃ+#ꢏꢒꢖ
0
0
0.00
0.50
(.23)
1.00
(.45)
1.50
(.68)
2.00
(.91)
2.50
(1.13)
3.00
(1.36)
3.50
(1.59)
4.00
(1.81)
ꢄꢅꢐꢁꢑꢃꢄꢅꢆ ꢃꢇꢅ"ꢈꢎꢋꢌ
ꢇ-ꢒꢎꢋꢌ
3A1334F
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Dimensions
a = 1/4 inch air inlet
b = 1/4 inch fluid outlet
c = 2 inch npt mounting configuration
d = ground screw
a
a
a
d
d
d
c
c
c
b
b
b
23.6 in.
600 mm
14.5 in.
370 mm
37.2 in.
945 mm
36.0 in.
915 mm
28.1 in.
715 mm
45.0 in.
1145 mm
35 pound drum
120 pound drum
400 pound drum
30
3A1334F
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Notes
3A1334F
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A1334
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2011, Graco Inc. is registered to ISO 9001
4/2011, revised March 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|