Instructions–Parts List
HIGH PRESSURE
Surge Tanks and
307296T
Fluid Filters
EN
For fluid surge reduction and for filtering of finishing materials.
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Fluid Filters
5000 psi (350 bar, 35 MPa) Maximum Working Pressure
Model 238620, Series A
Fluid Filter,
Fluid Filter,
Cover
Exposed Mounting
Exposed
Mounting
Mounting
Model 214724, Series E
Cover Mounting
1008
1009
Model 289310, Series A
Cover Mounting
Fluid Filter
7252 psi (500 bar, 50 MPa) Maximum Working Pressure
Model 237069, Series A
Exposed Mounting
Surge Tanks (with filter)
5000 psi (350 bar, 35 MPa) Maximum Working Pressure
Model 214624, Series C
Exposed Mounting
Model 238623, Series A
Exposed Mounting
Model 214726, Series E
Cover Mounting
Mastic Surge Tanks (without filter)
5000 psi (350 bar, 35 MPa) Maximum Working Pressure
Surge Tank,
Exposed
Mounting
Surge Tank,
Cover
Mounting
Model 214623, Series A
Exposed Mounting; for use with high viscosity fluids
Model 214725, Series C
Covered Mounting; for use with low to medium viscosity fluids
1008
1005
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The top of the surge tank must always be supported.
Typical Mountings
See Accessories on page 13 for mounting clamps.
See Fig. 1 for typical mountings. See page 14 for the
mounting hole layout.
Surge tanks must always be mounted upright, as
shown in Fig. 1, not horizontally.
Install the surge tank or filter near the pump outlet.
Position the surge tank so the labels face away from
the pump and so the setscrews, near the top and
bottom of the tank, face toward the pump.
Exposed Mountings
Detail A: With Riser Tube
Detail B: No Riser Tube
05910
Drum Cover Mountings
Detail D: Separate Riser Tube
Detail C: Integral Riser Tube
05912
Fig. 1
307296
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Surge Tank Conversion Kits
Connect the surge tank to the fluid outlet (F) of the
displacement pump and install the clamp in the option-
al outlet (E) at the base of the air motor. See Fig. 2.
Surge Tank Conversion Kits 238634 and
237704
Use Conversion Kits 238634 or 237704 to add a surge
tank to a pump. Kit 238634 includes surge tank
238623 (A) and clamp 238630 (B). Kit 237704 includes
surge tank 214624 (A), clamp 238630 (B), and attach-
ing hardware (C).
1
2
These parts are included with Conversion Kit 237704 only.
Model 238623 Surge Tank shown.
E
B
C
1
A
2
F
05927
Fig. 2
4
307296
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Before operating the equipment, be sure the drain
valve is closed.
Be sure the drain valve is fully closed when spraying
and fully open when draining or circulating fluid to get
the best results and reduce wear on the valve.
Flush the equipment with a compatible solvent to
remove oil used for factory testing and rust prevention.
If you notice excessive surging at the spray gun, shut
off the pump, trigger the gun to relieve fluid pressure,
and open the drain valve (D) at the bottom of the surge
tank. See Fig. 3. After the tank is drained, close the
drain valve and resume operation.
1
Open drain valve to relieve pressure.
1
D
1
D
05911
05913
Fig. 3
307296
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Pressure Relief Procedure
Service Notes
Clean all parts thoroughly when disassembling. Check
parts carefully for damage or wear, replace as needed.
WARNING
SKIN INJECTION HAZARD
Numbers in parentheses in the text refer to the parts
drawings.
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
Check periodically for leakage from the small holes
near the top and bottom of the surge tanks. If you find
leakage at the holes or anywhere else, replace the
seals promptly.
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
Before removing the end plug and adapter from the
surge tank, loosen the setscrews (5) near the bottom
of the tank (6). See the parts drawings on pages 7
through 12.
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the spray tips.
Inspect the sealing surfaces for nicks or scratches that
might cause leakage. Do not damage the sealing
surfaces.
1. Lock the gun trigger safety.
When reassembling filters after cleaning or servicing,
be sure to install the filter support as shown in the
parts drawings. Do not install it upside down.
2. Turn off the power to the pump.
3. Close any master bleed-type air valves.
4. Unlock the gun trigger safety.
WARNING
Tighten all threaded connections securely. High
pressure fluid can dislodge a loose connection or
allow high pressure fluid to be emitted from the
connection and cause serious injury.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
6. Lock the gun trigger safety.
7. Place a pail under the drain valve, and open the
drain valve to be sure all fluid pressure is relieved.
Keep hands away from the end of the drain valve
when opening it.
8. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the tip or hose.
6
307296
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 214724, Series E
See Accessories for other available screens.
Replace filter support if ridges are worn down.
1
2
1
Model 289310, Series A
Includes items 1–25
2
3
4
Lubricate.
Do not damage PTFE o-ring (7). Lubricate and
bend into kidney shape, then push into groove.
3
4
1
5
6
24
23
10
2
14
12
11
25
7
4
3
18
15
19
20
21
12
16
13
17
22
1007
Ref
No.
Ref
No.
Part No.
Description
Qty
Part No.
Description
Qty
1
2
3n
4
5
174058
104813
174056
171941
167025
167024
186075
104804
104839
102291
164900
175043
103337
RING, lock
PLUG, pipe, 3/8 npt
BOWL, filter
SPRING, conical compression
STRAINER, 60 mesh (Model 214724) 1
STRAINER, 30 mesh (Model 289310) 1
1
1
1
1
15
16
17
18
19
20
21
22
23
24
25
166697
165964
102310
172094
165273
206481
103648
165274
104663
174080
101754
STEM, valve
NUT, packing
NUT, acorn, no. 10–32
SEAT, ball
BALL, valve
SEAT, valve
PACKING, o-ring, fluoroelastomer
NIPPLE, adapter
PLUG, pipe, 3/4 npt
MANIFOLD
1
1
1
1
1
1
1
1
1
1
1
6
SUPPORT, filter
1
1
1
2
2
1
1
7n
10
11
12
13
14
PACKING, o-ring, PTFE
PLUG, pipe, 1/2 npt
PIN, drive
WASHER, flat
LEVER
PLUG, pipe, 3/8 npt
n Keep these spare parts on hand to reduce down time.
PACKING, o-ring, fluoroelastomer
307296
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 238620, Series A
1
2
Includes items 1–28
8
2
10
2
See Accessories for other available screens.
Replace filter support if ridges are worn down.
1
2
3
3
4
Lubricate.
Do not damage PTFE o-ring (7). Lubricate and
bend into kidney shape, then push into groove.
26
4
5
9
1
27
2
6
7
28
4
3
05908
Ref
No.
Ref
No.
Part No.
Description
Qty
Part No.
Description
Qty
1
2
3n
4
5
6
7n
8
174058
104813
174056
171941
167025
186075
104804
24C497
RING, lock
PLUG, pipe, 3/8 npt
BOWL, filter
SPRING, conical compression
STRAINER, 60 mesh
SUPPORT, filter
PACKING, o-ring, PTFE
MANIFOLD, paint filter
1
3
1
1
1
1
1
1
9
223960
104839
155665
205448
186447
BALL VALVE, see 306861 for parts
PLUG, pipe, 1/2 npt
UNION, adapter
COUPLING, swivel; 3/8 npsm(f)
TUBE, drain; nylon;
1/4 in. (0.6 mm) ID; 5 in. (127 mm)
1
1
1
1
10
26
27
28
1
n Keep these spare parts on hand to reduce down time.
8
307296
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 237069
1
2
Includes items 1–26
See Accessories for other available screens.
Replace filter support if ridges are worn down.
1
2
3
4
Lubricate.
Do not damage PTFE o-ring (7). Lubricate and
bend into kidney shape, then push into groove.
3
4
5 1
8
10
2
2
6 2
26
9
7
4
3
05909
Ref
No.
Ref
No.
Part No.
Description
Qty
Part No.
Description
Qty
1
2
3n
4
5
174058
104813
174056
171941
167025
186075
104804
RING, lock
PLUG, pipe, 3/8 npt
BOWL, filter
SPRING, conical compression
STRAINER, 60 mesh
SUPPORT, filter
1
3
1
1
1
1
1
8
9
10
26
24C497
224774
100737
156296
MANIFOLD, paint filter
DRAIN VALVE
PLUG, pipe, 1/2 npt
NIPPLE; 3/8 npt x 1/8 npt
1
1
1
1
6
7n
PACKING, o-ring, PTFE
n Keep these spare parts on hand to reduce down time.
307296
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
See Accessories for other
available screens.
Model 214624, Series C
Includes items 1–16, 31, 33, 34
1
5
1
Replace filter support if
ridges are worn down.
3
3
2
3
2
3
Model 214726, Series E
Includes items 1–13, 17–32, 34
Lubricate.
Do not damage PTFE o-ring (13).
Lubricate and bend into kidney
shape, then push into groove.
4
5
6
6
Torque to 150 ft–lb (200 N.m).
Torque to 40 in–lb (4.5 N.m).
5
6
11
11
34
3
3
3
3
2
3
3
2
6
5
7
12 5
8
9
12
5
4
13
3
4
1
13
15
14
3
31
30
23
31
19
15
17
18
32
33
16
24
25
26
27
28
10
2
20
17
21
29
22
1004
Ref
No.
Ref
No.
Part No.
Description
Qty
Part No.
Description
Qty
1
174064
104805
166612
111463
none
PLUG, end
RING, backup, PTFE
PACKING, o-ring, PTFE
SETSCREW,1/4–20 x 3/8”
TANK, accumulator not sold separately 1
ADAPTER, filter
SPRING, conical compression
STRAINER, 60 mesh
SUPPORT, filter
1
2
2
2
21
22
23
24
25
26
27
28
29
30
31
32
33
165964
102310
174080
101754
172094
165273
206481
103648
165274
104663
104839
102291
155665
169579
NUT, packing
NUT, acorn, No. 10–32
MANIFOLD
PLUG, pipe, 3/8 npt
SEAT, ball
BALL, valve
SEAT, valve
PACKING, o-ring, fluoroelastomer
NIPPLE, adapter
PLUG, pipe, 3/4 npt
PLUG, 1/2 npt
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2n
3n
5
6
7
174059
171941
167025
186075
174058
174068
104804
24C497
104813
210658
164900
175043
103337
166697
1
1
1
1
1
1
1
1
2
1
2
1
1
1
8
9
10
11
12n
13n
14
15
16
17
18
RING, lock
ADAPTER, accumulator
PACKING, o-ring, PTFE
MANIFOLD, paint filter
PLUG, pipe, 3/8 npt
BALL VALVE, see 306861 for parts
WASHER, flat
PIN, drive
UNION, adapter
LABEL, warning
34Y
n Keep these spare parts on hand to reduce down time.
LEVER
19
20
PACKING, o-ring, fluoroelastomer
STEM, valve
Y Replacement Danger and Warning labels, tags and cards
are available at no cost.
10 307296
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 238623, Series A
1
5
Includes items 1–36
3
3
2
3
11
See Accessories for other
available screens.
1
Replace filter support if
ridges are worn down.
2
3
5
6
3
2
3
3
6
Lubricate.
Do not damage PTFE o-ring (13).
Lubricate and bend into kidney
shape, then push into groove.
4
Torque to 150 ft–lb (200 N.m).
Torque to 40 in–lb (4.5 N.m).
5
6
5
12
13
4
3
34
15
14
31
15
6
1
5
7
8
9
33
16
35
36
10
2
05907
Ref
No.
Ref
No.
Part No.
Description
Qty
Part No.
Description
Qty
1
174064
104805
166612
111463
none
174059
171941
167025
186075
174058
174068
104804
24C497
PLUG, end
RING, backup, PTFE
PACKING, o-ring, PTFE
SETSCREW,1/4–20 x 3/8”
TANK, accumulator not sold separately 1
ADAPTER, filter
SPRING, conical compression
STRAINER, 60 mesh
SUPPORT, filter
1
2
2
2
15
16
31
33
34Y
35
36
104813
238612
104839
155665
169579
205448
186447
PLUG, pipe, 3/8 npt
BALL VALVE, see 306861 for parts
PLUG, 1/2 npt
UNION, adapter
LABEL, warning
COUPLING, swivel; 3/8 npsm(f)
TUBE, drain; nylon;
1/4 in. (0.6 mm) ID; 5 in. (127 mm)
2
1
1
1
1
1
2n
3n
5
6
7
1
1
1
1
1
1
1
1
8
9
1
10
11
12n
13n
14
RING, lock
n Keep these spare parts on hand to reduce down time.
ADAPTER, accumulator
PACKING, o-ring, PTFE
MANIFOLD, paint filter
Y Replacement Danger and Warning labels, tags and cards
are available at no cost.
307296 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 214623, Series A
5
3
4
1
Lubricate.
Includes items 1–12, 29
Do not damage PTFE o-ring (9).
Lubricate and bend into kidney
shape, then push into groove.
Model 214725, Series C
Includes items 1–9, 11, 13–29
2
3
3
3
Torque to 150 ft–lb (200 N.m).
Torque to 40 in–lb (4.5 N.m).
5
6
5
6
6
29
6
5
7
3
3
3
2
14
19
11
10
12
15
5
27
28
8
20
21
11
16
22
23
24
28
17
13
9
3
4
18
25
1006
Ref
Ref
No.
Part No.
Description
Qty
No.
Part No.
Description
Qty
1
174064
104805
166612
111463
none
174058
174068
104804
174060
104663
210658
175043
104839
103337
166697
165964
PLUG, end
RING, backup, PTFE
PACKING, o-ring, PTFE
SETSCREW, 1/4–20 x 3/8”
TANK, accumulator not sold separately 1
RING, lock
ADAPTER, accumulator
PACKING, o-ring, PTFE
MANIFOLD, accumulator
PLUG, pipe, 3/4 npt
BALL VALVE, see 306861 for parts
LEVER
PLUG, 1/2 npt
PACKING, o-ring, fluoroelastomer
STEM, valve
1
2
2
2
18
19
20
21
22
23
24
25
27
28
29Y
102310
174080
101754
172094
165273
206481
103648
165274
102291
164900
169579
NUT, acorn, No. 10–32
MANIFOLD
PLUG, pipe, 3/8 npt
SEAT, ball
BALL, valve
SEAT, valve
PACKING, o-ring, fluoroelastomer
NIPPLE, adapter
PIN, drive
WASHER, flat
LABEL, warning
1
1
1
1
1
1
1
1
2
2
1
2n
3n
5
6
7
1
1
1
1
1
1
1
1
1
1
1
8
9n
10
11
12
13
14
15
16
17
n Keep these spare parts on hand to reduce down time.
Y Replacement Danger and Warning labels, tags and cards
NUT, packing
are available at no cost.
12 307296
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Use Only Genuine Graco Parts and Accessories
SURGE TANK CLAMPS
PTFE SEALS
238630
For ball valves and drain valves.
For surge tanks mounted in the fluid outlet of the
displacement pump. Install the clamp in the optional
outlet at the base of the air motor. Requires 100902
screw, 100016 lockwasher and 100015 nut.
104892
104893
to replace 103648 fluoroelastomer seal
to replace 103337 fluoroelastomer seal
STAINLESS STEEL SCREENS
167024
167025
167026
167027
595 micron (30 mesh)
250 micron (60 mesh)
149 micron (100 mesh)
75 micron (200 mesh)
100902
100015
100016
172865
For surge tanks mounted in the optional fluid outlet of
Bulldog or King pumps when used with a riser tube.
Attach the clamp to the top of the air motor shield.
Requires 100902 screw, 100016 lockwasher, 100015
nut, and two 100270 screws.
100270
172865
100902
100016
100015
307296 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Mounting Hole
Layout
For mounting square base surge tanks and filters on a
drum cover or other support.
Category
Data
Maximum
Working
Pressure
Model 237069: 7252 psi (500 bar, 50
MPa)
All Other Models: 5000 psi (350 bar,
35 MPa)
Weight
Model 214623: 30 lb (13 kg)
Model 214624: 31.5 lb (14 kg)
Model 214724: 13 lb (6 kg)
Model 214725: 34 lb (15 kg)
Model 214726: 34 lb (15 kg)
Model 237069: 10.5 lb (4.5 kg)
Model 238620: 10.5 lb (4.5 kg)
Model 238623: 31.5 lb (14 kg)
Model 289310: 13 lb (6 kg)
2.38”
(60 mm) dia.
1.06”
(27 mm)
Surge Tank
Volume
15 oz. (450 ml)
2
2)
Filter Area
18 in (120 cm
Wetted Parts Stainless steel, zinc-plated steel,
nylon, PTFE, fluoroelastomer
0.312”
(8.12 mm) dia.
1.06” (27 mm)
14 307296
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
* For models 238620 and 238623, add approximately 6 in. (152 mm) to
the “A” dimension to account for the drain tube and fitting.
A*
C
C
B
B
A*
D
J
K
D
K
F
H
F
J
E
E
L
L
1005
G
1008
Filters
Paint Surge Tanks
Mastic Surge Tanks
214724 &
289310
214624 &
238623
Dimensions
238620
237069
214726
214623
214725
A
11.63 in.
(295 mm)
11.50 in.
(292 mm)
10.38 in.
(265 mm)
23.00 in.
(585 mm)
21.75 in.
(550 mm)
22.75 in.
(578 mm)
21.75 in.
(550 mm)
(see * note
above)
B
C
D
E
8.75 in.
(222 mm)
8.75 in.
(222 mm)
9.62 in.
(245 mm)
20.12 in.
(510 mm)
21.00 in.
(535 mm)
19.88 in.
(510 mm)
21.00 in.
(535 mm)
2.06 in.
(52 mm) dia.
2.06 in.
(52 mm) dia.
2.06 in.
3.00 in.
3.00 in.
3.00 in.
3.00 in.
(52 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia.
3.12 in.
(79 mm) dia.
3.12 in.
(79 mm) dia.
3.12 in. 3.12 in. 3.12 in. 3.12 in. 3.12 in.
(79 mm) dia. (79 mm) dia. (79 mm) dia. (79 mm) dia. (79 mm) dia.
3.00 in. 3.00 in. 3.00 in. 3.00 in. 3.00 in.
3.00 in.
(76 mm) dia.
3.00 in.
(76 mm) dia.
(76 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia.
Inlets
F
3/4 npt(f)
3/4 npt(f)
3/4 npt(f)
3/8 npt(f)
3/4 npt(f)
3/4 npt(f)
3/8 npt(f)
3/4 npt(f)
3/4 npt(f)
3/8 npt(f)
G
Outlets
H
3/8 npt(f)
1/2 npt(f)
3/8 npt(f)
3/8 npt(f)
1/2 npt(f)
3/8 npt(f)
3/8 npt(f)
1/2 npt(f)
3/8 npt(f)
3/4 npt(f)
3/4 npt(f)
J
K
1/2 npt(f)
3/4 npt(f)
1/2 npt(f)
3/4 npt(f)
1/2 npt(f)
3/4 npt(f)
Drain
L
3/8 npt(m)
1/8 npt(f)
1/4 npt(m)
3/8 npt(f)
1/4 npt(m)
3/8 npt(f)
1/4 npt(m)
Mtg. Holes
M(2)
1/4–20
1/4–20
1/4–20
307296 15
Download from Www.Somanuals.com. All Manuals Search And Download.
The Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers
to identify the distributor closest to you:
1–800–328–0211 Toll Free
612–623–6921
612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 307296
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES S P.O. BOX 1441 S MINNEAPOLIS MN 55440–1441 S USA
Copyright 1978, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised April 2013
16 307296
Download from Www.Somanuals.com. All Manuals Search And Download.
|