Instructions
EM Drive
Lubricators
3A0415D
ENG
Provides a continuous, precise and temperature independent supply of grease or oil
lubrication to all lubrication points of sliding- and roller bearings, drive- and transport
chains, sliding guideways, open gears and seals. For professional use only.
Not approved for use in European explosive atmospheres.
75 psi (0.5 MPa, 5 bar) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
This equipment is suitable for use in Class I,
Division 2, Groups A, B, C and D, Class II, Division
2, Groups F and G and Class III Hazardous
Locations or non-hazardous locations only.
EXPLOSION HAZARD
Substitution of components may impair
suitability for Class I, Division 2.
C
US
BAYZ,BAYZ7
92 UM
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest
rated system component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See
Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s
warnings. For complete information about your material, request MSDS from
distributor or retailer.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is
not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with
genuine manufacturer’s replacement parts only.
• Do not alter or modify equipment.
• Do not puncture, open or take lubricator apart.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot
surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in
the operating area of the equipment to help protect you from serious injury, including
eye injury, hearing loss, inhalation of toxic fumes, and burns. This equipment includes
but is not limited to:
•
Protective eyewear, and hearing protection.
•
Respirators, protective clothing, and gloves as recommended by the fluid and sol-
vent manufacturer.
3A0415D
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Identification
Pressure Relief Procedure
B
A
C
1. Cover lubrication point (A) and lubricator
(B) with a heavy rag to absorb any fluid that
may leak out while loosening the adapter.
2. Carefully unscrew support adapter (D) from
the lubrication point (A).
D
A Lubrication Point
B Lubrication Canister
C Drive Unit
D Support Adapter
Component Identification
D
E
C
B
A
A Plug
D ◆battery pack (includes 3 size AA
B Lubrication Canister
batteries, each 1.5V)
NOTE: Canister cannot be refilled.
E † Cover
C † Drive Unit (Includes gear motor and
circuit board)
◆ New batteries must be used for every lubrication cartridge replacement. Never reuse batteries.
† Reusable part
4
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
Installation and Setup
Determining Correct Mounting Method
NOTE:
NOTE:
•
Be sure to use a lubricant cartridge that
contains the same grease used in the
application.
•
•
Direct mounting should be used for lubrica-
tion points that are easily accessible.
Remote mounting is recommended if you
answer YES to any of the questions below.
•
The best measurement results are
achieved during operation.
1. Is the ambient temperature at the lubrica-
tion point higher than +40°C (104°F)?
Checking the Counter Pressure
2. Is it necessary to remove protective
screens, walls or other types of protection
in order to reach the lubrication point?
1. Clean the lubrication point to remove any
potential contaminants.
2. Prime the grease line and all accessories
with the same grease that is contained in
complete list of available grease car-
tridges).
3. Is the lubrication point exposed to high
vibrations?
4. Is it difficult to access the lubrication point
during operation of the machine?
3. Remove the plug (A).
5. Is the lubrication point exposed to any of
the following:
•
water jets for high-pressure cleaning
machines?
•
•
•
corrosive chemicals?
high temperatures?
falling materials?
A
4. Install lubricator unit
into adapter (B).
Preparing Lubricator for Installation
5. Install reducers,
extensions, grease
line, etc. (if neces-
sary).
The lubricator has a self-protection mecha-
nism which shuts off the drive unit at counter
pressures higher than 5 bar (72.5 psi). Most
bearings require 0.5 - 2 bar (7.2 to 29 psi)
pressure (without tubes, extensions, angles,
etc.).
6. Screw a pressure
manometer into the
lubrication point (dd)
(FIG. 1, page 6).
B
Use the following procedure to check the coun-
ter pressure of the application prior to installa-
tion.
3A0415D
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
A pressure manometer is a simple device that
measures pressure output. To build a pressure
manometer you need a pressure gage (aa),
tee fitting (bb) and stop valve (cc). FIG. 1
shows a correctly assembled pressure
manometer, connected to the lubricator and a
lubrication point.
12.To disconnect lubricator from manometer,
follow pressure relief procedure provided
on page 4.
NOTE: In this application, you will be dis-
connecting adapter (B) from manometer
instead of lubrication point.
dd
bb
ff
NOTICE
Do NOT disconnect lubricator from adapter
(B). Screwing anything into lubricator end a
second time will damage self-sealing threads.
cc
ee
aa
13.If the counter pressure is 5 bar (72.5 psi) or
higher, flush the lubrication point with a
grease gun.
FIG. 1
aa
Pressure Gauge
bb
cc
dd
ee
ff
Tee Fitting
Stop Valve
Lube Point
Lubricator
If the counter pressure does not decrease
you may need a different lubricant or size
lubricator canister. Contact Graco Cus-
tomer service for assistance.
ON / OFF Switch
Priming/Prefilling Fittings and
Grease Lines
7. Ensure the stop valve (cc) of the pressure
manometer is open.
All accessories and grease lines must be
primed/pre filled. Without this priming/pre fill-
ing, the lubricator would first have to fill the
accessories with lubricant.
8. Attach lubricator and adapter (B) to the
pressure manometer (aa - cc) and turn the
switch to “ON” (ff) (FIG. 1).
9. Run the manometer for about 20 seconds.
Observe the gauge and repeat this proce-
dure until the pressure registered on the
gauge stays constant.
Example: A tube that is one meter long
3
requires about 28 cm of lubricant. It would
take the lubricator with a 12 month setting and
an EM-120 grease canister about 3 months to
fill this 1 meter tube.
10.To determine the counter pressure, wait
approximately 5 minutes until the system
has relaxed. Do one more discharge by
turning the unit OFF; then ON again until it
dispenses for no more than 5 seconds.
grease gun to dispense the grease.
11.Wait approximately 5 more minutes to
make sure the system does not lose pres-
sure and remains constant.
FIG. 2
6
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
Circuit Board Settings
Function Display
Red and green LED’s (Light Emitting Diodes) are on the circuit board and visible through the
transparent cover. The following signals about operating conditions/malfunctions are displayed by
these LED’s for the user:
LED
Signal
Signal Time
Every 15
seconds
Every 8
Meaning
Green
Blinking
System functions OK
Red
Blinking
Malfunction / error
seconds
Green
and Red
Red
Every 3
seconds
Steady
Lubricator unit is empty.
Change canister.
Unit is discharging lubricant.
Blinking
Steady signal
There is a 4-way code switch on the circuit board. TIME switches 1 + 2 are used to set the dis-
charge period. VOL switches 3 + 4 are used to set the size of the lubrication canister.
Setting Dip Switches
1. Unscrew and remove the cover.
D
Setting the Discharge Period (TIME)
2. Use a small screwdriver or your finger to
A
move dip switches to the desired position.
B
•
•
•
The discharge period is pre-set to 6
months.
Dip switches 1+2 marked “TIME” are
used to set the discharge period.
C
switch position.
1
2
3
4
FIG. 3
Dip Switch Position Options: Time
A LED Red
B LED Green
C 4-way code switch
D battery pack contacts
There are 4 switch position options: 1, 3, 6 and
for each option.
1 Months 3 Months 6 Months 12 Months
1
2
1
2
1
2
1
2
Time
Time
Time
Time
FIG. 4
3A0415D
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
Setting the Lubrication Canister Volume
Dip Switch Position Options: Volume
There are 3 switch position options. These
positions correspond to each of the 3 lubrica-
tion canister sizes: 60 cc, 120 cc, 250 cc. Refer
3. Use a small screwdriver or your finger to
move dip switches to the desired position.
•
Dip switches 3+4 marked “VOL” are
used to set the lubrication canister size.
If the 4-way code switch does not corre-
spond to the actual size of the lubrica-
tion canister, it will lead to a wrong
signal and over or under lubrication.
60 cc
120 cc
250 cc
3
4
3
4
3
4
Vol.
Vol.
Vol.
•
switch position.
FIG. 5
TABLE 1: Dip Switch Settings
•
•
Amount of discharge shown in cc (1cc = 0.9 gram lubricant) per day.
The white square indicates dip switch position.
Lubrication
Canister Size
60 cc
120 cc
250 cc
Dip Switch
Position
3
4
3
4
3
4
Discharge
VOL
VOL
VOL
period
2.00
4.00
8.33
1 month
1
2
TIME
0.67
1.33
2.78
3 months
1
2
TIME
0.33
0.17
0.67
0.33
1.39
0.69
6 months
1
2
TIME
12 months
1
2
TIME
8
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
•
For horizontal mounting a bracket clip must
be used to hold the lubricator in place. A
horizontal clip bracket part number 124086
is available from Graco. See Parts, page 16
Changing the Dip Switch Setting
The discharge period (Time) and/or lubrication
canister size (Volume) can only be changed
when a new lubrication canister is attached. If
settings must be changed during current oper-
ation; i.e., after discharge was started, you
must attach a new, completely filled lubrication
canister and a new battery pack.
•
•
For vertical installations always use a sup-
port adapter part number 124105 is avail-
able from Graco. See Parts, page 16.
The grease nozzle of the lubricator has a
npt 1/4 inch male thread. If your application
has a different thread you may need to use
plete list of available adapters.
Changing settings during operation interferes
with the controls and monitoring electronics;
making it impossible to guarantee precise
lubrication.
•
•
Do not overtighten the plastic thread of the
lubricator.
Always use a new, completely full
lubrication canister and new battery pack
after each setting change. Never use a
partially empty lubrication canister or old
batteries.
For all metal to metal connections (i.e.,
extensions, reducers, etc.) make sure to
®
use LOCTITE 243* (semi-tight screw lock-
ing).
®
Selecting Mounting Location
*Loctite is a registered trademark of the Loctite
Corporation.
Installation Guidelines
Direct Mounting Installation
incorrect direct mounting installations.
•
Before installing the lubricator, the lubrica-
tion points and any extensions must be
adequately pre-lubricated with the same
lubricant contained in the lubricator. A 400
gram lubricant cartridge for grease guns is
available from Graco. See Parts, page 16
for a complete list of available lubricant car-
tridges.
Correct
•
•
Install one lubricator per lubrication point.
Incorrect
When oil is used for lubrication, a
non-return valve (oil throttle) must be
installed. This will prevent oil leakage from
the lubricator. An oil throttle, part number
124102 is available from Graco. See Parts,
•
An oil-filled lubricator must be installed ver-
tically (outlet down).
FIG. 6
3A0415D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
Grease Lubrication with Tube
Remote Mounting Installations
rect remote mounting installations.
A
•
•
Remote installations require a grease line.
Graco recommends using a 5/16 inch flexi-
ble hose.
Select a position for the lubricator that is
easy to access and protected from
high-pressure water jets, falling materials,
corrosive chemicals and extreme tempera-
tures.
B
C
D
E
F
FIG. 7
A Clip, 124086
B Support adapter, 124105
C Bracket, 124087
D Tube connector◆, (User supplied)
E Nylon tube◆ (User supplied)
F Tube connections◆ (User supplied)
◆ Must be at least 5/16 inch diameter tube.
10
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
From-top-lubrication of a Chain with Oil
A Clip, 124086
B Support adapter, 124105
C Bracket, 124087
D Tube connector◆ (User supplied)
E Nylon tube◆ (User supplied)
F Tube connections◆ (User supplied)
G Oil throttle, 124102*
A
H L-Bracket, 124098
J Bulkhead mounting plate, 124099
K Oil brush, 1”x 1.5”, 124090
L Chain
*The non-return valve (oil throttle (G) should
always be placed at the lowest point of the
application.
◆ Must be at least 5/16 inch diameter tube.
B
C
D
E
F
H
G
J
C
K
L
FIG. 8
3A0415D
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
9. Install lubricator unit
into adapter (B) (if it is
not already installed).
Installing Lubricator to
Lubrication Point
1. Clean the lubrication point to remove any
potential contaminants.
10.Screw lubricator to
lubrication point,
hand tight only.
2. Verify the thread of the lubricator corre-
sponds to the thread of the screw point.
B
3. Verify Dip Switches are correctly set. See
NOTICE
To ensure optimal lubrication:
4. Prime the grease line and all accessories
with the same grease that is contained in
complete list of available grease car-
tridges).
• Seal threads of all connecting parts with a
suitable, standard sealant.
• Mount oil filled lubricators properly with the
outlet pointing down.
5. Install reducers, extensions, grease line,
etc. (if necessary).
• Never screw in the lubricator a second time
or the self-sealing threads will be dam-
aged.
6. Place drive unit on top of new lubrication
canister until the teeth of both pieces are
locked.
• For remote mounting installations, make
sure bracket does not squeeze the lubrica-
tion canister as this could block the piston
inside the canister.
7. Screw the cover of the drive unit onto the
lubrication canister - hand tighten only.
8. (If the plug is not
already removed),
remove the plug (A).
A
Operation
Before operation verify:
•
For oil filled lubrication canisters, an oil
throttle must be attached.
•
•
The lubricator does not have any visible
damage.
•
•
New batteries have been installed.
The “VOL” switches 3 and 4 of the 4-way
code switch match the correct size of the
lubrication canister.
The lubricator canister is filled with the
requested grease or oil.
12
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
•
•
The “TIME” switches 1 and 2 of the 4-way
code switch in the drive unit match the
desired discharge period.
Removing Lubrication Canister
1. Switch the rotary switch
position from ON to OFF.
All components are properly assembled
and screwed together hand tight.
To begin the discharge:
Turn the rotary switch from the
OFF position to the ON posi-
tion.
2. To disconnect adapter from lubrication
point, follow pressure relief procedure
3. Unscrew and completely remove adapter
(B) from the lubricator. Adapter will be
reused.
Maintenance
Changing the Lubrication
Canister
When the red and green LED light up at the
same time, the lubrication canister is empty
and should be replaced.
NOTICE
B
•
•
The battery pack must be replaced
every time you change a lubrication
canister to ensure correct lubricator
operation.
FIG. 9
4. Unscrew cover from drive unit.
The drive unit and circuit board must
always be protected from moisture to
prevent damaging these components.
Always change the lubrication canister
in a dry place.
5. Remove drive unit from the lubrication can-
ister.
6. Remove old battery pack from drive unit.
3A0415D
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
7. Remove the plug (A).
Installing the New Lubrication
Canister
Sparking can occur when changing the bat-
tery pack. Only replace the battery pack in a
non-hazardous location, away from flammable
fluids or fumes.
A
8. Install lubricator unit
into adapter (B).
1. Install new battery pack in drive unit in the
NOTE: Only replace the battery pack with a
Graco battery pack for EM Drive Lubricators,
part number 124261. Handle and dispose of
the battery pack properly.
9. Screw lubricator into
the lubrication point -
hand tighten only.
B
NOTICE
To ensure optimal lubrication:
• Seal threads of all connecting parts with a
suitable, standard sealant.
Direction Arrow
• Mount oil filled lubricators properly with the
outlet pointing down.
FIG. 10
• Never screw in the lubricator a second time
or the self-sealing threads will be dam-
aged.
2. If a different size lubrication canister or dis-
charge period is going to be used, change
dip switches to reflect the new canister size
• For remote mounting installations, make
sure bracket does not squeeze the lubrica-
tion canister as this could block the piston
inside the canister.
3. Prime the grease line and all accessories
with the same grease that is contained in
complete list of available grease car-
tridges).
10.To begin the discharge refer to Operation,
4. Install reducers, extensions, grease line,
etc. (if necessary).
5. Place drive unit on top of new lubrication
canister until the teeth of both pieces are
locked.
6. Screw the cover of the drive unit onto the
lubrication canister - hand tighten only.
14
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Lubrication Canister Disposal
Storage
When lubricators are not immediately installed,
they must be stored for a maximum of 1 year in
a dry, dust free, sunlight protected room,
indoors. The room temperature cannot exceed
70°F (21°C).
Dispose of hazardous fluid in approved con-
tainers, and according to applicable guidelines.
Read the MSDS to know the specific hazards
of the fluids you are using.
Troubleshooting
Malfunction
Possible Cause
Solution
Switches on the cover are in
the OFF position
Move switches to ON position
Install new battery pack
No batteries are installed in the
drive unit
Lubricator does not function
Old batteries were used
Batteries are leaking
Install new battery pack
Replace drive unit
Parts are not correctly screwed Correctly screw parts together
together
or screw tighter
The red and green blinking
LED display signals “end of
discharge period” but lubrica- or adjusted wrong at the begin-
Settings were changed during
the currently running operation
Replace with full lubrication
canister. Install new battery
pack and restart.
tion unit is not empty yet
ning
Old batteries were used
Install new battery pack
Unit has been operating below
-10°C (14°F) for a long period
of time
Operate the unit within the
specified temperature range
Unit does not discharge
Settings were changed during
the currently running operation
or adjusted wrong at the begin-
ning
Replace with full lubrication
canister. Install new battery
pack and restart.
Settings were changed during
the currently running operation
or adjusted wrong at the begin-
ning
The green blinking LED display
signals “system in operation”
but the lubrication unit is empty
Replace with full lubrication
canister. Install new battery
pack and restart.
Clean line and connection
parts. Turn unit OFF and then
ON again.
Clogged line and/or connection
parts
The red blinking LED display
signals “system malfunction”
Counter-pressure is too high
Lower counter-pressure
3A0415D
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Parts
Miscellaneous Accessories
Replacement Cap
Part No. Description
Qty. Part No. Description
Qty.
123949 MOTOR, EM-Drive
124086 CLIP, support
1
1
1
1
1
1
1
1
1
1
124110 CAP, top
124111 CAP, full, 60-120 cc
124112 CAP, full, 250 cc
1
1
1
124087 BRACKET, plastic
124089 BRUSH, pig hair, 1/4 fnpt - 3/4
124090 BRUSH, oil, 1 x 1.5
124091 BRUSH, oil, 1 x 2.4
124092 BRUSH, oil, 1 x 4
124093 BRUSH, link chain
124100 CLAMP, beam, 1”
124101 BRACKET, dual unit
124102 VALVE, check, oil throttle
124109 KIT, accessory, purge
124110 CAP, wet, EM-Drive
124111 CAP, full, 60 - 120 cc
124112 CAP, full, 250 cc
124113 APPLICATOR, chain, felt
124114 BRUSH, nylon, 1/8 mnpt x 5/8
124115 BRUSH, nylon, 1/8 mnpt x 2
124116 KIT, SA heavy green
124119 PADDLE, open gear lube
400 Gram Lubricant Cartridges
Part No. Description
124176 CARTRIDGE, lubricant, lith-
ium EP-2
124177 CARTRIDGE, lubricant, con-
struction
124178 CARTRIDGE, lubricant, bear-
ing
124179 CARTRIDGE, lubricant, milling
124180 CARTRIDGE, lubricant, food
grade H1
124181 CARTRIDGE, lubricant, syn-
thetic industrial
124182 CARTRIDGE, lubricant, ultra
spindle
124183 CARTRIDGE, lubricant, lith-
ium EP-1
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Mounting Brackets
Part No. Description
Qty.
124094 BRACKET, mounting, small
124095 BRACKET, mounting, medium
124096 BRACKET, mounting, large
124097 BRACKET, mounting, flat
124098 BRACKET, mounting, L
1
1
1
1
1
1
124099 BRACKET, mounting, bulkhead
Fitting Adapter
Part No. Description
Qty.
124105 ADAPTER, 1/4 fnpt x 1/4 mnpt
124106 ADAPTER, 1/4 fnpt x 1/8 mnpt
1
1
Pressure Relief Valve
Part No. Description
Qty.
124107 VALVE, relief, 1/8 m, 5 lb
124108 VALVE, relief, 1/8 m, 1 lb
1
1
16
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Refill Kits
Part No. Description
Qty.
Part No. Description
Qty.
24E597 KIT, refill, 120 cc, lithium EP-1
24E598 KIT, refill, 250 cc, lithium EP-2
24E599 KIT, refill, 250 cc, construction
24E600 KIT, refill, 250 cc, bearing
24E601 KIT, refill, 250 cc, milling
24E602 KIT, refill, 250 cc, food grade H1
24E603 KIT, refill, 250 cc, synthetic
24E604 KIT, refill, 250 cc, ultra spindle
24E605 KIT, refill, 250 cc, lithium EP-1
24H340 KIT, refill, 120 cc, EM bearing
24H341 KIT, refill, 250 cc, EM bearing
1
1
1
1
1
1
1
1
1
1
1
24E582 KIT, refill, 60 cc, lithium EP-2
24E583 KIT, refill, 60 cc, construction
24E584 KIT, refill, 60 cc, bearing
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
24E585 KIT, refill, 60 cc, milling
24E586 KIT, refill, 60 cc, food grade H1
24E587 KIT, refill, 60 cc, synthetic
24E588 KIT, refill, 60 cc, ultra spindle
24E589 KIT, refill, 60 cc, lithium EP-1
24E590 KIT, refill, 120 cc, lithium EP-2
24E591 KIT, refill, 120 cc, construction
24E592 KIT, refill, 120 cc, bearing
24E593 KIT, refill, 120 cc, milling
24E594 KIT, refill, 120 cc, food grade H1
24E595 KIT, refill, 120 cc, synthetic
24E596 KIT, refill, 120 cc, ultra spindle
Technical Data
Power Supply
Temperature range
Maximum output pressure
Storage
3 AA, 1.5V batteries
-10° C to +50° C (+14° F to +122° F)
5 bar (75 psi)
Conditions
Dry, dust free
Temperature
+20° C 5° C (+68° F 9° F)
Noise data: Sound pressure level <70 dB(A) measured at distance of 1m (39.4 in.) / height 1.6m
(63 in.)
®
Loctite is a registered trademark of the Loctite Corporation.
3A0415D
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Discharge Amount per Cycle
Discharge Amount per Discharge Cycle
Discharge
Period
Pause
Time
EM-60
EM-120
EM-250
3
3
3
Months
h:min
fl. oz.
0.004
fl oz.
fl. oz.
cm
cm
cm
1
3
1:30
4:37
0.13
0.26
0.008
0.53
0.17
6
9:17
12
18:36
Weights and Measurements
Type
Volume
Diameter (D)
Length (L) Weight (empty)
3
fl. oz mm
in.
2.8
2.8
2.8
mm
142
165
215
in.
kg
lbs
cm
EM-60 60 2.03
EM-120 120 4.06
EM-250 250 8.45
71
71
71
5.60
6.50
8.46
0.376 0.829
0.386 0.851
0.417 0.919
1/4 npt
LC unit
Drive
D
L
18
3A0415D
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Notes
3A0415D
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A0415
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2010, Graco Inc. is registered to ISO 9001
12/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|