Graco Scuba Diving Equipment 312497F User Manual

Instructions

Trabon

Divider Valves

312497F

For series progressive, oil and grease lubrication. For Professional Use Only.

Important Safety Instructions

Read all warnings and instructions in this

manual. Keep these instructions.

Models/Maximum Pressure

Table 1: Maximum Pressure Lube Points

Table 2: MGO Series-Flo Divider Maximum

Operating Pressures

Maximum

Operating

Maximum Operating

Pressure kPSI

(MPa, bar)

Maximum

Sections

Pressure kPSI (MPa, bar) Number of Sections

Divider Type

6.0 (41.4, 414)

5.5 (37.9, 379)

4.0 (27.6, 276)

4.5 (31.0, 310)

4.0 (27.6, 276)

3 to 7

3.0 (20.7, 207)

2.0 (13.8, 138)

3.5 (24.1, 241)

7.5 (51.7, 517)

3.0 (20.7, 207)

See Table 2

MJ/MJSS

MSP

MHH

MXP

MGO

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

Component Identification

Setup

Inlet

Section

The divider valve is shipped ready to install in your sys-

tem. It has been factory-tested and should not require

any additional modification.

Valve

Section

NOTICE

Indicator/ Port Plug

Do not install a divider valve into a system rated for

more than the valve’s maximum operating pressure.

This type of installation could result in o-ring damage

and cause the divider valve to leak.

Crossport

Plate

End Plug

Subplates with

Output Ports

To install the divider valve in your system:

1. Determine an appropriate, remote mounting loca-

tion.

End

Section

2. Install a rupture to atmosphere fitting with a blow-out

disk that is rated for 7,500 psi or less between the

force feed lubricator pump and master divider valve

inlet.

TI11117

Tie Rod Nut

3. Install an analog pressure gauge at the inlet to the

divider valve.

FIG. 1

Table 3: Typical Divider Valve

Combinations

4. Install a slow or no cycle shutdown in one of the pis-

ton enclosure plugs. Program it to shut down after

no more than 180 seconds without a complete

cycle.

TYPE OF

APPLICATION

MASTER SECONDARY

5. Torque. See Table 4 on page 15.

Machine tools, Printing,

Wire Forging &

As long as lubricant is supplied under pressure to the

inlet section of the divider assembly, valves sections will

continue to operate in a progressive manner. Divider

assemblies always follow a constant discharge pattern.

Whenever lubricant flow ceases, the valving pistons will

stop. When flow resumes, it will start again at the same

point in the discharge cycle.

Packaging Machinery

MSP

MJ, MSP

Machine tools, Textile,

Glass & Can Machinery,

Mobile Equipment

MX, MXP

MGO

MX, MXP, MSP

Cranes, Presses, Steel

Mills, etc.

Levellers, Shears,

Conveyors, etc.

Divider Valves

A Series-Flo type divider valve is a manifold proportion-

ing device consisting of an inlet and end section plus a

minimum of three valve sections. The divider valve is

manifolded together with tie rods and nuts. A master

divider valve is the first divider valve downstream from

the lube pump. A secondary divider valve is any divider

valve receiving lubricant from the master divider valve.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

Valve Sections (MSP, MHH and MXP

modular-type, divider valves, only)

Prefilling Lubricant Distributor Lines

Follow the following procedure exactly as written, in the

order written.

Valve sections (three or more required per manifold)

contain a piston specially fitted to that section, built in

outlet check valves and various passageways that,

working with the piston, meters and valves the flow of

lubricant (FIG. 2).

NOTICE

•

The initial startup and operation is the most critical

operating period for a newly installed machine in

terms of potential for being damaged by unre-

moved/unfiltered lubricant contaminants and lack of

adequate lubrication. Proper prefilling of lubrication

system ensures that lubricant is immediately avail-

able to every lube point during machine startup,

protecting them from damage.

Piston

Enclosure/End

Plug

Enclosure Plug Gasket

O-Rings

Piston

•

Use only clean oil filtered to the SAE -recom-

mended cleanliness level of ISO 18/14 (ISO Stan-

dard 4406) when prefilling a system. The

manufacturers of the machine tool and its compo-

nent bearings should be consulted to ensure that

the ISO 18/14 cleanliness level is adequate.

Check

Valve

TI11102

Indicator

Port

Indicator Port Plug

FIG. 2

Filling Secondary-to-Lube Point Lines

Valve sections may be manufactured to require one or

two lube outlets. Stamping located on the face of each

section indicates:

Refer to FIG. 3. when performing this procedure

•

the style of divider valve section, i.e., MSP, MX,

etc.,

the discharge per piston stroke expressed in

LUBE POINT

thousandths of cubic inches (35 = .035 in )

BLEED HOSE

HERE

and,

SECONDARY

MASTER

REMOVE INDICATOR

•

the number of lube outlets required (S = single,

one outlet only; T = twin, two lube outlets

required).

OR PORT PLUG

TI11098

HAND PUMP

FIG. 3

1. Remove port plugs or performance indicators from

all of the indicator ports on front of secondary

divider valves.

2. Connect a hand pump filled with clean, filtered lubri-

cant to the indicator port closest to the first line to be

filled that corresponds to the output port that is feed-

ing the line to be filled.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

3. In order to verify when lubricant is flowing and has

reached the end of the lube line, loosen the connec-

tor at the lube point of the line that is to be filled.

4. Continue to stroke the pump until the lubricant

purges all the air out of the internal passages of the

secondary divider valve and lubricant flows freely

from all indicator ports with no evidence of included

air.

4. Stroke the hand pump until air-free lubricant is

observed flowing from the end of the lube line.

5. Reinstall the port plugs or performance indicators in

their respective positions in the secondary divider

valve. Do not replace the port plugs or performance

indicators in the master divider valve yet.

5. Tighten the lube line connector at the lube point, but

do not replace the port plugs or performance indica-

tors into the ports on the front of the working sec-

tion.

6. Repeat Steps 1-5 for each of the other lube lines

between the master divider valve and all other sec-

ondary divider valves.

6. Repeat steps 1-5 for each of the other lube lines

connected to the other outlet ports in the secondary

divider valve assembly and for any other secondary

divider assemblies in the system.

NOTE: Do not replace any of the performance indicators

or port plugs removed in Step 1 from the master divider

valve assembly until the air-purging procedure

described in Section 3 (Filling Master Divider Valve) has

been completed.

NOTE: Do not replace any of the performance indicators

or port plugs removed in Step 1 until the line-filling pro-

cedure described in Section 2 (Filling Master -to-Sec-

ondary Lube Lines) has been completed.

Filling Master-to-Secondary Lube Lines

Refer to FIG. 4. when performing this procedure.

LUBE POINT

SECONDARY

BLEED

THROUGH

MASTER

ALL PORTS

REMOVE INDICATOR

OR PORT PLUG

TI11099

HAND PUMP

FIG. 4

1. Remove the port plugs or performance indicators

from all the indicator ports on the front of the master

divider valve.

2. Connect a hand pump filled with clean, filtered lubri-

cant to the indicator port closest to the lube output

port that is feeding the line to the secondary divider

valve.

3. Stroke the hand pump to fill the line between the

master divider valve and secondary divider valve.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

Filling Master Divider Valve

Refer to F IG . 5. when performing this procedure.

LUBE POINT

SECONDARY

MASTER

BLEED

HERE

CYCLE PUMP

TI11000

FIG. 5

1. Verify that all port plugs or performance indicators

have been removed from all indicator ports in the

master divider valve.

2. Verify that the system pump is properly connected

to the inlet port of the master divider valve.

3. Cycle the system pump sufficiently to fill the main

feeder line between the pump and the master

divider valve and the lubricant is observed being

discharged from all of the indicator ports on the front

of the master divider valve with no evidence of

included air.

4. Reinstall the master divider valve port plugs or per-

formance indicators into their respective positions.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

General Repair Instructions

Purging Air From the System

Before machine operation is resumed following mainte-

nance or repair, manual system air purging must be per-

formed.

•

Before performing any repair procedures, relieve

pressure, page 2.

There are several air purging procedures available

depending upon the maintenance or repair procedure.

Pressure test distribution blocks yearly or every

8000 hours. Replace seals and divider valves as

necessary.

NOTE: Use only clean oil filtered to the SAE -recom-

mended cleanliness level of ISO 18/14 (ISO Standard

4406) when prefilling a system. The manufacturers of

the machine tool and its component bearings should be

consulted to ensure that the ISO 18/14 cleanliness level

is adequate.

Page

Section

Air purging after:

Replacing line between a secondary divider valve and lube point.

Replacing a line between the master divider valve and a secondary

divider valve.

Replacing a line between pump and master divider valve.

Adding or replacing any component in a master divider valve assembly.

Adding or replacing any component in module in a secondary divider

valve assembly.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

Section 1: Purging Air from Secondary Divider Valve Lube-to-Lube Point Lines

LUBE POINT

BLEED HOSE

SECONDARY

HERE

MASTER

REMOVE INDICATOR

OR PORT PLUG

HAND PUMP

TI11098

FIG. 6

Steps 1-6, refer to F IG . 6.

1. Install the line from the secondary divider valve to

the lube point, but do not completely tighten the

connection at the lube point.

2. Remove the performance indicator port plug or the

performance indicator from the working valve sec-

tion on the secondary divider valve assembly corre-

sponding to the outlet port and the line connected to

the lube point.

3. Attach a hand pump filled with clean, filtered lubri-

cant to the port on the secondary divider valve that

was opened in Step 2.

4. Operate the hand pump until air-free lubricant is

observed flowing from the line at the lubrication

point.

5. Tighten the fitting at the lubrication point while lubri-

cant is still flowing.

6. Remove the hand pump and reinstall the perfor-

mance indicator or indicator port plug removed in

Step 2.

NOTE: If check valves were not installed at the lubrica-

tion point, lubricant may continually drain out of the line

when the secondary port is open. Therefore, when

check valves are not used, the method for bleeding this

line is to tighten the line at both ends and repeatedly

cycle the secondary divider valve via hand pump opera-

tion until lubricant, free of air, flows from the lubrication

point

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

Section 2: Purging Air from Master to Secondary Divider Valve Lube Lines

LUBE POINT

BLEED HERE

FIRST

SECONDARY

MASTER

REMOVE INDICATOR

OR PORT PLUG

AFTER BLEEDING INLET,

REMOVE ALL INDICATORS

OR PORT PLUGS AND BLEED

ALL PORTS

HAND PUMP

TI11113

FIG. 7

Steps 1- 9, refer to FIG. 7.

5. Tighten the fitting at the secondary valve’s inlet

while lubricant is still flowing.

1. Install the lines from the master divider valve to the

secondary divider valve, but do not completely

tighten the connection at the secondary divider

valve’s inlet.

6. Remove all of the indicators or indicator port plugs

from the secondary divider valve’s working sections.

7. Operate the hand pump again until air-free lubricant

is observed flowing out of all the secondary divider

valve’s indicator ports.

2. Remove the performance indicator port plug or the

performance indicator from the working valve sec-

tion on the master divider valve assembly corre-

sponding to the outlet port and the line connected to

the secondary valve.

8. Reinstall all of the performance indicators or port

plugs in the secondary divider valve while lubricant

is still flowing from the ports.

3. Attach a hand pump filled with clean, filtered lubri-

cant on the master divider valve that was opened in

Step 2.

9. Remove the hand pump and reinstall the perfor-

mance indicator or indicator plug removed in Step 2

into the master divider working valve’s open port.

4. Operate the hand pump until air-free lubricant is

observed flowing freely from the secondary valve’s

lube inlet connector.

The system is now ready for operation.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

Section 3: Purging Air from Pump to Master Divider Valve Lines

LUBE POINT

SECONDARY

MASTER

BLEED THROUGH

ALL PORTS

TI11114

SYSTEM PUMP

FIG. 8

Steps 1-3, refer to F IG . 8.

1. Install the line from the system pump to the master

divider valve, but do not completely tighten the con-

nection at the master valve’s lube inlet.

2. Cycle the system pump until air-free lubricant is

observed flowing from the line at the master divider

valve’s lube inlet.

3. Tighten the fitting at the lube inlet port while lubri-

cant is still flowing.

The system is now ready for operation.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

Section 4: Purging Air After Adding or Replacing a Master Divider Valve Module

LUBE POINT

SECONDARY

BLEED

HERE

DISCONNECT

LINE

MASTER

HAND PUMP

NEW VALVE

BLOCK

TI11116

FIG. 9

Steps 1-7, refer to FIG. 9.

1. Install the new or replacement module into the mas-

ter divider valve assembly. Also connect the tubing

or hoses to the appropriate secondary divider

valve(s) or lubrication point(s) if the new/replace-

ment module is a base section.

5. Operate the hand pump until air-free lubricant is

observed flowing from each secondary valve’s lube

inlet connector and/or each lubrication point’s con-

nector.

6. Tighten the fitting at the secondary valve inlet or at

the lubrication port while lubricant is still flowing.

2. Do not completely tighten the connection(s) at the

secondary divider valve’s inlet or at lubrication

points.

7. Remove the hand pump and reconnect the system

pump to the inlet of the master divider valve.

3. Disconnect and remove the line from the pump at

the inlet of the master divider valve.

The system is now ready for operation.

4. Attach a hand pump filled with clean, filtered lubri-

cant to the inlet port on the master divider valve.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

Section 5: Purging Air After Adding or Replacing a Secondary Divider Valve Module

BLEED HOSE

HERE

LUBE POINT

SECONDARY

MASTER

BLEED

HERE

NEW VALVE

BLOCK

REMOVE INDICATOR

OR PORT PLUG

HAND PUMP

TI11115

FIG. 10

Steps 1-8, refer to F IG . 10.

1. Install the new or replacement module to the sec-

ondary divider valve assembly. Also connect the

tubing or hoses to the appropriate lubrication point if

the new/replacement module is a base section.

5. Operate the hand pump until air-free lubricant is

observed flowing from the loosened connector at

the lube point.

6. Tighten the fitting at the lube point while lubricant is

still flowing.

2. Do not completely tighten the connection(s) at the

lubrication point.

7. Repeat Steps 3 - 6 for any additional lubrication

points connected to the new module.

3. Remove the performance indicator or indicator port

plug from the working valve section on the second-

ary divider valve assembly corresponding to the out-

let port and line connected to a particular lube point.

8. Remove the hand pump and reinstall the perfor-

mance indicator or port plug removed in Step 3 into

the secondary divider valve’s open port.

4. Attach a hand pump filled with clean, filtered lubri-

cant to the port on the secondary divider valve that

was opened in Step 3.

The system is now ready for operation.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

Rupture Indicator

Locating and Repairing

Blockages

Blocks will cause a higher than normal pumping pres-

sure. Depending on the application or system design,

this blockage will usually result in a complete loss of

lubricant flow into the total system and no bearing will be

receiving lubrication.

Rupture indicators are used on MSP/MH divider valve

applications where lube system pressure exceed 2500

psi. The high pressure from the lube line blockage

causes a disc to rupture. The lubricant then forces an

indicator to protrude, locating the blockage. The high

pressure backs up through the system and trips a switch

to shut the system off. When the fault is corrected, the

disc must be replaced and the pin reset manually.

The loss of flow due to a blockage is first indicated with

the higher than normal system pressure that is devel-

oped by the pump as it attempts to overcome this block-

age. Higher pressure is limited, isolated and signaled

through the use of various performance indicators, reset

and relief, incorporated into the system design.

Automatic Relief Indicator

An automatic relief indicator pinpoints lube line blockage

but allows the lube system to continue supplying lubri-

cant to points that are not blocked. They are used pri-

marily in secondary divider valves. The excessive

pressure created by line blockage moves a piston,

enabling the lubricant to escape through a vent. When

the pressure is relieved, the spring resets the piston.

Because these devices permit the lube system to keep

operating when a lube point is blocked, a separate pres-

sure switch connected to an audible alarm should be

used to warn of high pressure.

Performance Indicators

Performance indicators are pressure-sensitive devices

that pinpoint excessive pressure in the lubricating sys-

tem.

These devices are installed in the indicator ports of

divider valves, signal a fault either by causing an indica-

tor pin to protrude or by releasing lubricant into the

atmosphere.

Locating and Repairing Blockages

1. Make a visual inspection of the system. Check for

crushed lines or improper divider valve installation.

NOTE: Never block a lube outlet that is designed to dis-

charge lubricant.

2. Verify that each divider valve outlet required to dis-

charge lubricant can do so and that no pipe plugs

have been installed in an outlet designed to serve a

bearing or another divider valve.

Reset Indicator with Memory

Reset indicators stop lube system operation when a

fault occurs. These devices can be used in either master

or secondary divider valves.

3. Use a manual pump with a gauge. Fill the pump with

clean, filtered lubricant. Connect the manual pump

to the inlet of the master divider valve and slowly

operate pump. If system will not cycle freely, below

1500 psi, see Master Divider Valve Equipped with

Performance Indicator [Step 4a (below)].

When a lube line becomes blocked, the resultant high

pressure pushes the indicator pin through the opening in

the cap. The high pressure prevents the affected divider

valve piston from completing its cycle, causing a pres-

sure backup through the divider valve which trips a pres-

sure switch upstream from the valve and shuts off the

pump.

NOTE: Use only clean oil filtered to the SAE -recom-

mended cleanliness level of ISO 18/14 (ISO Standard

4406) when prefilling a system. The manufacturers of

the machine tool and its component bearings should be

consulted to ensure that the ISO 18/14 cleanliness level

is adequate.

The indicator pin remains extended until it is reset man-

ually. This helps locate the lube line that is blocked.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

4a. Master Divider Valve Equipped With Performance

NOTE:

Indicator

•

If all indicator port plugs are removed, the master

will not cycle. Blockage is in this divider valve.

With manual pump connected to the master divider

valve as outlined in Locating Blockages, Step 3,

raise pressure to 2000 psi. The indicators in the

indicator ports will signal the location of the block-

age. An indicator in the up position indicates pres-

sure is in that outgoing line and signals the blockage

is in the area being served from this outlet (FIG. 11).

•

When indicator port plug of a blocked area is

removed, a small shot of trapped lubricant will usu-

ally surge out of this outlet as the inlet pressure on

the divider valve drops.

•

If testing (Step 4) indicates a blockage in the master

divider valve, this divider valve must be disassem-

bled and cleaned. See Clean Divider Valve, Step 7,

page 15.

If no indicator pins are protruding, the blockage is in

the master divider valve.

HAND PUMP

SYSTEM PUMP

LUBE

OUTLETS

LUBE

OUTLETS

INDICATOR PIN UP

INDICATOR

PORT

PLUGS

MASTER

DIVDER

VALVE

MASTER

DIVDER

VALVE

REMOVED

SECONDARY

DIVIDER

VALVE

SECONDARY

DIVIDER

VALVE

TI11103

FIG. 11

TI11104

4b. Master Divider Valve Equipped Without Performance

FIG. 12

Indicator

5. If in Step 4, a blockage has been indicated

downstream of the master divider valve, install a

manual pump in the indicator port of the master

divider valve that is common to the blocked area.

(See FIG. 12).

1) With manual pump connected to the master

divider valve as outlined in Locating Blockages,

Step 3, raise pressure to 2000 psi.

2) Remove, one at a time, each indicator port plug

and attempt to operate manual pump after each

plug is removed. Do not exceed 2000 psi.

a. Proceed to downstream secondary divider valve

and remove all indicator port plugs.

b. Slowly operate manual pump. If lubricant can be

discharged freely through each of the indicator

ports of this divider valve, the blockage is not in

the supply line or the divider valve. Go to step 6.

3) If pressure drops and the master cycles freely

after an indicator port plug is removed, then

blockage is downstream in the area that is being

served from that outlet. See Locating Block-

ages, Step 3.

If lubricant is not freely discharged through

open indicator ports of the second divider valve,

the blockage is in this divider valve or its supply

line. Disconnect supply line at secondary inlet

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

fitting and slowly operate manual pump to verify

location. If blockage is in this divider valve, go to

step 7.

NOTE: Dirt and foreign material will damage lubricating

equipment. Perform all service and disassembly under

the cleanest possible conditions.

a. Before disassembling any divider valve, make a

sketch noting the arrangement of Valve Sec-

tions. For example: INLET 10T - 20S - 10T -

30S - END (FIG. 14). Also remove end plugs

only and try to move each piston back and forth

without removing the piston from the valve sec-

tion.

LUBE

OUTLET

SYSTEM PUMP

MASTER

DIVDER

VALVE

Inlet

10T

LUBE OUTLETS

20S

INDICATOR PORT

PLUGS REMOVED

10T

30S

End

FIG. 14

NOTICE

SECONDARY

DIVIDER

VALVE

Do not insert hard metal objects into piston bore (i.e.,

punches, screwdrivers, etc.). Hard metal objects can

damage the surface and cause divider valves to leak

fluid. Use a brass rod and hand pressure only.

HAND PUMP

BEARING

FIG. 13

b. If all pistons move freely and there is no indica-

tion of a more serious problem, replace end

plugs.

6. Install manual pump into each indicator port of sec-

ondary divider valve in turn and slowly operate

pump (F IG . 13). If high pressure exists, blockage

has been located. Look for crushed line, tight

bearing, improperly drilled fittings and/or lube

inlet port. Correct as necessary.

c. Using a new gasket, tighten and torque as indi-

cated in Table 1 (page 11).

7. Clean Divider Valve

Table 4: Torque Values (*see F IG . 1, page 3)

Assembly Torque (ft-lbs)

MSP/MH

5-8

MXP

6-9

MGO

Tie Rod Nuts

Indicator Plugs*

End Plugs*

6-7

11-13

8-9

12-15

46-50

12-13

6-8

12-15

8-9

Valve Section

Mounting Screw

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

d. Clean sections and pistons in suitable clean sol-

Separation Blockage

vent until all lubricant has been removed.

If a hard wax or soap-like material is found in the Valve

Section, grease separation is occurring. This means that

the oil is being squeezed from the grease at normal sys-

tem operating pressure and the grease thickener is

being deposited in the divider valve. Cleaning the divider

valve will only temporarily solve the problem. Consult

your lubricant supplier for recommendations on alter-

nate lubricants and your local Graco/Trabon distributor

to verify compatibility with centralized lubricating sys-

tems.

e. Use compressed air to dry and blow out all

ports thoroughly.

A small metal probe should be used to make

sure all passages are clean and open.

Inspect cylinder bore and piston carefully for

scratches, score marks or other damage.

If all indictor port plugs are removed, master will not

cycle. Blockage is in this divider valve.(FIG. 11).

NOTE: If either piston or cylinder bore is damaged, a

new section must be installed. All pistons are selectively

fitted to the bore for proper clearance. Be sure to rein-

stall piston only into the valve section from which it was

removed.

f. If divider valve section and piston both appear in

good condition, reassemble section making cer-

tain piston slides smoothly but snugly in cylinder

bore.

g. Repeat cleaning and inspection of each section.

After all sections have been cleaned, blown out,

inspected and found to be in good condition,

reassemble divider valve using notes and

sketches (Step 7) as a reference.

NOTE:

•

Always use new gaskets.

Test operation of divider valve using manual pump.

Contamination Blockage

If dirt, foreign material or any other form of contamina-

tion is found in a divider valve, cleaning that divider valve

will only temporarily solve contamination blockage prob-

lems. The source of the contamination must be elimi-

nated for satisfactory service.

The system filtering method must be investigated, filter

elements should be inspected and cleaned if necessary.

The reservoir filling method should be reviewed to elimi-

nate any chance of foreign material entering the reser-

voir during filling.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MD Series

Technical Data

Dimensions

Material

Steel

Pressure (max)

Lubricant

3,000 psi (207 bar)

Oil or grease

1-lb. 8 oz (0.68 kg)

1.46

(37.0)

Net Weight (approx.)

CYCLE INDICATOR

PIN (OPTIONAL)

0.28

(7.11)

Volume (Lubricant to cycle

divider valve one complete

cycle)

OUTLET

0.87

(22.0)

1.19

(30.2)

MD-2, MD-3, MD-4

0.080 in. (1.31 ccm)

MD-6

2.12

(53.9)

0.060 in. (0.98 ccm)

0.40

(10.7)

0.28

(7.11) Dia. 2-Mtg. Holes

Torque Ratings

Assembly Bolts

Enclosure Plugs

Indicator Plug

Outlet Plugs

8-9 ft. lbs

11-13 ft. lbs

15 ft. lbs

1.25

1.75

(31.7)

(44.4)

0.25

(6.3)

3.00

(76.2)

6-7 ft. lbs.

3.12

(79.3)

Assembly

Bolts

Parts

,5"% ).,%4

1.19

(30.2

0.87

(22.0)

Ref Part No. Description

0.28

(7.11)

562656 VALVE, feeder, MD 2

562657 VALVE, feeder, MD 3

562658 VALVE, feeder, MD 4

1.21

(30.9)

562659 VALVE, feeder, MD 6

1/8”OUTLET

562653 VALVE, feeder, MD 2, IND

562654 VALVE, feeder, MD 3, IND

562655 VALVE, feeder, MD 4, IND

563270 VALVE, feeder, MD 2, IND/Switch

563271 VALVE, feeder, MD 3, IND/Switch

564356 VALVE, feeder, MD 4, IND/Switch

1.19

(30.2

0.87

(22.0)

LUBE INLET

0.28

(7.11)

1.21

(30.9)

ꢀꢁꢂv/54,%4 ꢃ-$ꢄꢅ /NLY

1/8” OUTLET

ti11472

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MJ Series

Technical Data

Dimensions

3.23

(82.2)

Material

Plated or Stainless Steel

2,000 psi (138 bar)

Pressure (max)

Lubricant

1.06

(26.9)

Oil or grease up to NLGI

Grade 1

CYCLE INDICATOR PIN (OPTIONAL)

Max Operating Temperature

200°F (93°C)

60 CPM

.750

(19.0)

Max Cycle Rate With

Cycle Pin

1.37

Net Weight (approx.)

3 section divider valve

4 section divider valve

5 section divider valve

6 section divider valve

7 section divider valve

8 section divider valve

Torque Ratings

(34.9)

LUBE INLET

INDICATOR OUTLET

4 MTG. HOLES

1-lb. 15 oz (0.88 kg)

2 lbs. 5 oz (1.04 kg)

2 lbs. 11 oz (1.21 kg)

3 lbs. 1 oz (1.38 kg)

3 lbs. 7 oz (1.55 kg)

3 lbs. 13 oz (1.72 kg)

1.09

(27.7)

.750

(19.0)

.270 (6.8)

.858

(21.79)

LUBE

OUTLET

.582 TYPICAL

(14.7)

Tie Rod Nut

12 ft. lbs

.250

(6.3)

Enclosure Plug

11-13 ft. lbs

6-7 ft. lbs.

Outlet Port Plugs

.687

(17.4)

2.12

(53.9)

2.54

(64.5)

ti11474

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MJ Series

Parts

Ref Part No. Description

562500 VALVE, assembly, MJ 5S

562501 VALVE, assembly, MJ 10S

562502 VALVE, assembly, MJ 15S

562503 VALVE, assembly, MJ 5T

562504 VALVE, assembly, MJ 10T

562505 VALVE, assembly, MJ 15T

562508 VALVE, assembly, IND MJ 10S

562512 VALVE, assembly, IND MJ 10S Left

562510 VALVE, assembly, IND MJ 10 T

562513 VALVE, assembly, IND MJ 10T Left

562509 VALVE, assembly, IND MJ 15S

562511 VALVE, assembly, IND MJ 15T

564205 VALVE, assembly, IND MJ 15T Left

562506 VALVE, assembly, SST MJ 5S SST

562507 VALVE, assembly, SST MJ 10S SST

564203 VALVE, assembly, SST MJ 5T SST

564204 VALVE, assembly, SST MJ 10T SST

560643 INLET, CRS, MJ

560644 INLET, SST, MJ

560645 END, CRS, MJ

561405 END, SST, MJ

557515 ROD, tie, MJ 3 (3 required)

557516 ROD, tie, MJ 4 (3 required)

557517 ROD, tie, MJ 5 (3 required)

557518 ROD, tie, MJ 6 (3 required)

557519 ROD, tie, MJ 7 (3 required)

557520 ROD, tie, MJ 8 (3 required)

560649 ROD, tie, MJ 9 (3 required)

558917 ROD, tie, MJ 3 SST(3 required)

124028 ROD, tie, MJ 4 SST(3 required)

124029 ROD, tie, MJ 5 SST (3 required)

124030 ROD, tie, MJ 6 SST (3 required)

124031 ROD, tie, MJ 7 SST (3 required)

124032 ROD, tie, MJ 8 SST (3 required)

124033 ROD, tie, MJ 9 SST (3 required)

556371 NUT, tie rod, 1/4-28 (3 required)

558633 NUT, tie rod, 1/4-28 SST (3 required)

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MSP Series

Technical Data

Material

Corrosion Protected Steel (optional: Type 316 Stainless

Steel)

Pressure (max)

Zero Leak Inlet

1500 psi (104 bar)

3000 psi (207 bar)

140°F (60°C)

Shunt/Shutoff Inlet

Ambient Temperature (max)

Lubricant

Zero Leak Inlet

Oil Only - up to 5000 SUS, requires 25 micron (min) filtra-

tion

Shunt/Shutoff Inlet

Oil and fluid grease - filter oil through 25 micron filter and

grease through 100 micron mesh strainer

New Weight (approx.)

3 section divider valve assembly

4 section divider valve assembly

5 section divider valve assembly

6 section divider valve assembly

7 section divider valve assembly

8 section divider valve assembly

Torque Ratings

5.9 lbs (2.7 kg)

7.3 lbs (3.3 kg)

8.7 lbs (4.0 kg)

10.2 lbs (4.6 kg)

11.6 lbs (5.6 kg)

13.0 lbs (5.9 kg)

Mounting Screw

8-9 ft. lbs

6-8 ft. lbs

5-7 ft. lbs

1-2 ft. lbs.

5-8 ft. lbs.

Enclosure Plugs

Indicator Port Plug

Bleed Screws

Tie Rod Nut

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MSP Series

Dimensions

CROSSPORT PLATE (OPTIONAL)

ti11478

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MSP Series

Parts

Ref Part No. Description

24B488 VALVE, single, 303 MSP .040 w/indicator

24B489 VALVE, twin, 303 MSP .020 w/indicator

24B490 VALVE, twin, 303 MSP .025 w/indicator

24B491 VALVE, twin, 303 MSP .030 w/indicator

24B492 VALVE, twin, 303 MSP .035 w/indicator

24B493 VALVE, twin, 303 MSP .040 w/indicator

24B497 BLOCK, base, 303 MSP

563425 BLOCK, base, MSP NPSF

563447 BLOCK, base, MSP, BSPP

563451 BLOCK, base, MSP, SAE

563479 BLOCK, base, MSP w/No outlets

560919 BLOCK, inlet, MSP, NPSF

560936 BLOCK, inlet, MSP, BSPP

560943 BLOCK, inlet, MSP, SAE

560976 BLOCK, inlet, MSP, ISO 6149

563421 BLOCK, inlet, MSP, NPSF, w/bleed

563422 BLOCK, inlet, MSP SAE w/bleed

563279 BLOCK, MSP end w/alt inlet

563424 BLOCK, end, MSP

563469 KIT, crossport bar, right

563470 KIT, crossport bar, left

563471 KIT, crossport bar, both

563472 KIT, singling bar

562660 VALVE, assembly bypass, standard MSP

557731 ROD, tie, 3 section, MSP (3 required)

557732 ROD, tie, 4 section, MSP (3 required)

557733 ROD, tie, 5 section, MSP (3 required)

557734 ROD, tie, 6 section, MSP (3 required)

557735 ROD, tie, 7 section, MSP (3 required)

557736 ROD, tie, 8 section, MSP (3 required)

557738 ROD, tie, 9 section, MSP (3 required)

557739 ROD, tie, 10 section, MSP (3 required)

557740 ROD, tie, 11 section, MSP (3 required)

556371 NUT, 1/4 - 28 (3 required)

562711 VALVE, assembly MSP 05S

562712 VALVE, assembly MSP 10S

562713 VALVE, assembly MSP 15S

562714 VALVE, assembly MSP 20S

562715 VALVE, assembly MSP 25S

562716 VALVE, assembly MSP 30S

562717 VALVE, assembly MSP 35S

562718 VALVE, assembly MSP 40S

562720 VALVE, assembly MSP 05T

562721 VALVE, assembly MSP 10T

562722 VALVE, assembly MSP 15T

562723 VALVE, assembly MSP 20T

562724 VALVE, assembly MSP 25T

562725 VALVE, assembly MSP 30T

562726 VALVE, assembly MSP 35T

562727 VALVE, assembly MSP 40T

562729 VALVE, assembly IND MSP 20S

562730 VALVE, assembly IND MSP 25S

562731 VALVE, assembly IND MSP 30S

562732 VALVE, assembly IND MSP 35S

562733 VALVE, assembly IND MSP 40S

562734 VALVE, assembly IND left MSP 20S

562735 VALVE, assembly IND left MSP 25S

562736 VALVE, assembly IND left MSP 30S

562737 VALVE, assembly IND left MSP 35S

562738 VALVE, assembly IND left MSP 40S

562739 VALVE, assembly IND MSP 20T

562740 VALVE, assembly IND MSP 25T

562741 VALVE, assembly IND MSP 30T

562742 VALVE, assembly IND MSP 35T

562743 VALVE, assembly IND MSP 40T

562744 VALVE, assembly IND left MSP 20T

562745 VALVE, assembly IND left MSP 25T

562746 VALVE, assembly IND left MSP 30T

562747 VALVE, assembly IND left MSP 35T

562748 VALVE, assembly IND left MSP 40T

24B474 VALVE, single, 303 MSP .005

562755 VALVE, single, 303 MSP .010

24B475 VALVE, single, 303 MSP .015

562756 VALVE, single, 303 MSP .020

24B476 VALVE, single, 303 MSP .025

24B477 VALVE, single, 303 MSP .030

24B478 VALVE, single, 303 MSP .035

562757 VALVE, single, 303 MSP .040

24B479 VALVE, twin, 303 MSP .005

562758 VALVE, twin, 303 MSP .010

24B480 VALVE, twin, 303 MSP .015

562759 VALVE, twin, 303 MSP .020

24B481 VALVE, twin, 303 MSP .025

24B482 VALVE, twin, 303 MSP .030

24B483 VALVE, twin, 303 MSP .035

562760 VALVE, twin, 303 MSP .040

24B484 VALVE, single, 303 MSP .020 w/indicator

24B485 VALVE, single, 303 MSP .025 w/indicator

24B486 VALVE, single, 303 MSP .030 w/indicator

24B487 VALVE, single, 303 MSP .035 w/indicator

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MSP Series

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MHH Series

Technical Data

Material

Steel Body (corrosion protected) Steel Piston (honed fit)

6,000 psi (414 bar) for Petroleum Oil only - Buna O-rings

Pressure (max)

7,500 psi (517 bar) for Petroleum or Synthetic Oil - fluo-

roelastomer O-rings

Lubricant

Petroleum or synthetic oil only

Maximum Operating Temperature

Buna-N O-rings (422-010-060)

Fluoroelastomer O-rings (527-000-840)

Maximum Cycle Rate Without Cycle Pin

Net Weight (approx.)

200°F (93°C)

350°F (163°C)

200 CPM

3 section divider valve assembly

4 section divider valve assembly

5 section divider valve assembly

6 section divider valve assembly

7 section divider valve assembly

8 section divider valve assembly

Torque Ratings

5.9 lbs (2.7 kg)

7.3 lbs (3.3 kg)

8.7 lbs (4.0 kg)

10.2 lbs (4.6 kg)

11.6 lbs (5.6 kg)

13.0 lbs (5.9 kg)

Mounting Screw

8-9 ft. lbs

6-8 ft. lbs

5-7 ft. lbs

1-2 ft. lbs.

5-8 ft. lbs

Enclosure Plugs

Indicator Port Plug

Bleed Screws

Tie Rod Nut

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MHH Series

Dimensions

1.500

(38.1)

",%%$ 3#2%73

2.188

1.656

(42.06)

(55.56)

.781

(19.9)

1.125

(28.58)

.406

(10.31)

.734

(18.85)

LUBE

INLET

LUBE

OUTLET

(TYPICAL)

PISTON ENCLOSURE PLUG (TYPICAL)

.922 (TYP)

(23.41)

3.000

(76.2)

.625

(15.9)

1.750

(44.4)

.484

(12.3)

OUTLET IS PLUGGED

ON ONE SIDE WHEN

WORKING SECTION IS

SINGLED

"A"

MOUNTING SCREW

(TYPICAL)

.484

(12.3)

.28

(7.1)

INDICATOR PORT

(TYPICAL)

.281 (7.137) DIA

(4) MTG HOLES

TIE ROD AND NUT

(TYPICAL)

ti11480

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MHH Series

Parts

Ref Part No. Description

563422 BLOCK, inlet, MHH SAE w/bleed

563451 BLOCK, base, MHH, SAE

562679 VALVE, assembly MHH 06S

562680 VALVE, assembly MHH 09S

562681 VALVE, assembly MHH 12S

562682 VALVE, assembly MHH 18S

562683 VALVE, assembly MHH 24S

562684 VALVE, assembly MHH 30S

562685 VALVE, assembly MHH 06T

562686 VALVE, assembly MHH 09T

562687 VALVE, assembly MHH 12T

562688 VALVE, assembly MHH 18T

562689 VALVE, assembly MHH 24T

562690 VALVE, assembly MHH 30T

563425 BLOCK, base, MHH, NPSF

563447 BLOCK, base, MHH, BSPP

563451 BLOCK, base, MHH, SAE

563479 BLOCK, base, MHH w/no outlets

560919 BLOCK, inlet, MHH, NPSF

560936 BLOCK, inlet, MHH, BSPP

560943 BLOCK, inlet, MHH, SAE

560976 BLOCK, inlet, MHH, ISO 6149

563421 BLOCK, inlet, MHH, NPSF, w/bleed

563279 BLOCK, MHH end w/alt inlet

563424 BLOCK, end, MHH

563469 KIT, crossport bar, right

563470 KIT, crossport bar, left

563471 KIT, crossport bar, both

563472 KIT, singling bar

562660 VALVE, assembly bypass

557731 ROD, tie, 3 section (3 required)

557732 ROD, tie, 4 section (3 required)

557733 ROD, tie, 5 section (3 required)

557734 ROD, tie, 6 section (3 required)

557735 ROD, tie, 7 section, (3 required)

557736 ROD, tie, 8 section (3 required)

557738 ROD, tie, 9 section (3 required)

557739 ROD, tie, 10 section (3 required)

557740 ROD, tie, 11 section (3 required)

556371 NUT, 1/4 - 28 (3 required)

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MXP Series

Technical Data

Material

Zinc Plated Steel

3,000 psi (207 bar)

Oil or grease

350°F (177°C)

60 CPM

Pressure (max)

Lubricant

Maximum Operating Temperature

Maximum Cycle Rate With Cycle Pin

Maximum Cycle Rate Without Cycle Pin or With Prox

Cycle Switch

200 CPM

Net Weight (approx.)

3 section divider valve assembly

4 section divider valve assembly

5 section divider valve assembly

6 section divider valve assembly

7 section divider valve assembly

8 section divider valve assembly

9 section divider valve assembly

10 section divider valve assembly

Torque Ratings

18-lb. 2 oz (8.3 kg)

22 lbs. 6 oz (10.2 kg)

26 lbs. 9 oz (12.2 kg)

31 lbs. 3 oz (14.2 kg)

35 lbs. 6 oz (16.2 kg)

39 lbs. 9 oz (18.1 kg)

44 lbs. 3 oz (20.1 kg)

48 lbs. 6 oz (22.1 kg)

Tie Rod Nut

6-9 ft. lbs

Enclosure Plugs

48 +/- 2 ft. lbs

12 -15 ft. lbs

12-13 ft. lbs.

Indicator Plug

Valve Section Mounting Screw

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MXP Series

Dimensions

,5"% ).,%4

).$)#!4/2 0/24

,5"% /54,%4

ꢃ/04)/.!,

ti11477

#2/33 0/24 0,!4% ꢃ/04)/.!,

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MXP Series

Parts

Ref Part No. Description

562834 VALVE, single, .150 MXP w/indicator

563519 BLOCK, BSPLT interm MXP 1/4 NPSF

563521 BLOCK, BSPLT interm MXP SAE

563522 BLOCK, BSPLT interm MXP 1/4 BSPP

563479 BLOCK, base, MSP/MHH w/no outlets

56R994 BLOCK, inlet, MXP

563518 BLOCK, end, machine MX

563524 KIT, MXP, crossport bar, left

563525 KIT, MXP, crossport bar, right

563526 KIT, MXP, crossport bar, both

562813 VALVE, twin, .025 MXP

562814 VALVE, twin, .050 MXP

562815 VALVE, twin, .075 MXP

562816 VALVE, twin, .100 MXP

562817 VALVE, twin, .125 MXP

562818 VALVE, twin, .150 MXP

562819 VALVE, single, .025 MXP

562820 VALVE, single, .050 MXP

562821 VALVE, single, .075 MXP

562822 VALVE, single, .100 MXP

562823 VALVE, single, .125 MXP

562824 VALVE, single, .150 MXP

562825 VALVE, twin, .050 MXP w/indicator

562826 VALVE, twin, .075 MXP w/indicator

562827 VALVE, twin, .100 MXP w/indicator

562828 VALVE, twin, .125 MXP w/indicator

562829 VALVE, twin, .150 MXP w/indicator

562830 VALVE, single, .050 MXP w/indicator

562831 VALVE, single, .075 MXP w/indicator

562832 VALVE, single, .100 MXP w/indicator

562833 VALVE, single, .125 MXP w/indicator

15R997 BLOCK, bypass, MXP

557766 ROD, tie, 3 section, MXP (3 required)

557767 ROD, tie, 4 section, MXP (3 required)

557768 ROD, tie, 5 section, MXP (3 required)

557769 ROD, tie, 6 section, MXP (3 required)

557770 ROD, tie, 7 section, MXP (3 required)

557771 ROD, tie, 8 section, MXP (3 required)

557772 ROD, tie, 9 section, MXP (3 required)

563520 ROD, tie, 10 section, MXP (3 required)

555406 NUT, 5/16 - 24 light hex (3 required)

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MGO Series

Technical Data

Material

Zinc Plated Steel and Phosphate Coated Cast Iron

Pressure (max)

3-7 section divider valve assembly

8 section divider valve assembly

9 section divider valve assembly

10 section divider valve assembly

11 section divider valve assembly

Lubricant

6000 psi (414 bar)

5500 psi (380 bar)

5000 psi (345 bar)

4500 psi (311 bar)

4000 psi (276 bar)

Oil or grease

Maximum Operating Temperature

Maximum Cycle Rate With Cycle Pin

200°F (93°C)

60 CPM

Maximum Cycle Rate Without Cycle Pin or With Prox

Cycle Switch

200 CPM

Net Weight (approx.)

3 section divider valve assembly

4 section divider valve assembly

5 section divider valve assembly

6 section divider valve assembly

7 section divider valve assembly

8 section divider valve assembly

9 section divider valve assembly

10 section divider valve assembly

11 section divider valve assembly

Torque Ratings

45-lb. (20.41 kg)

53 lbs. 5 oz (24.18 kg)

61 lbs. 10 oz (27.95 kg)

70 lbs. 15 oz (32.17 kg)

80 lbs. 4 oz (36.40 kg)

89 lbs. 9 oz (40.62 kg)

98 lbs. 14 oz (44.84 kg)

108 lbs. 3 oz (49.07 kg)

117 lbs. 8 oz (53.40 kg)

Tie Rod Nut

12 ft. lbs

Enclosure Plug

15 ft. lbs

Outlet Port Plug

6-8 ft. lbs

12-13 ft. lbs.

Valve Section Mounting Screw

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MGO Series

Dimensions

).,%4

/54,%43

).$)#!4/2 0/243

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MGO Series

Parts

Ref Part No. Description

562570 VALVE, MGO, assembly 150S SAE

562571 VALVE, MGO, assembly 300S SAE

562572 VALVE, MGO, assembly 450S SAE

562573 VALVE, MGO, assembly 600S SAE

562574 VALVE, MGO, assembly 150T SAE

562575 VALVE, MGO, assembly 300TS SAE

562576 VALVE, MGO, assembly 450T SAE

562577 VALVE, MGO, assembly 600T SAE

562578 VALVE, MGO, assembly 150S SAE IND

562579 VALVE, MGO, assembly 300S SAE IND

562580 VALVE, MGO, assembly 450S SAE IND

562581 VALVE, MGO, assembly 6000S SAE IND

562582 VALVE, MGO, assembly 150T SAE IND

562583 VALVE, MGO, assembly 300T SAE IND

562584 VALVE, MGO, assembly 450T SAE IND

562585 VALVE, MGO, assembly 600T SAE IND

563277 INLET,

563278 END

560591 ROD, tie, short MGO 3 (2 required)

560592 ROD, tie, short MGO 4 (2 required)

560593 ROD, tie, short MGO 5 (2 required)

560594 ROD, tie, short MGO 6 (2 required)

560595 ROD, tie, short MGO 7 (2 required)

560596 ROD, tie, short MGO 8 (2 required)

560597 ROD, tie, short MGO 9 (2 required)

560598 ROD, tie, short MGO 10 (2 required)

560599 ROD, tie, short MGO 11 (2 required)

560600 ROD, tie, long MGO 3 (2 required)

560601 ROD, tie, long MGO 4 (2 required)

560602 ROD, tie, long MGO 5 (2 required)

560603 ROD, tie, long MGO 6 (2 required)

15U857 ROD, tie, long MGO 7 (2 required)

560604 ROD, tie, long MGO 8 (2 required)

560605 ROD, tie, long MGO 9 (2 required)

560606 ROD, tie, long MGO 10 (2 required)

560607 ROD, tie, long MGO 11 (2 required)

555406 NUT, tie rod 3/8 - 24 lock (8 required)

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MX Series

Technical Data

Material

Plated Steel

3,000 psi (207 bar)

Oil or grease

200°F (93°C)

60 CPM

Pressure (max)

Lubricant

Maximum Operating Temperature

Maximum Cycle Rate With Cycle Pin

Maximum Cycle Rate Without Cycle Pin

Net Weight (approx.)

200 CPM

3 section divider valve assembly

4 section divider valve assembly

5 section divider valve assembly

6 section divider valve assembly

7 section divider valve assembly

8 section divider valve assembly

9 section divider valve assembly

10 section divider valve assembly

Torque Ratings

21-lb. 6 oz (9.69 kg)

25 lbs. 10 oz (11.62 kg)

29 lbs. 14 oz (13.55 kg)

34 lbs. 2 oz (15.47 kg)

38 lbs. 6 oz (17.40 kg)

42 lbs. 12 oz (19.39 kg)

47 lbs. 2 oz (21.37 kg)

51 lbs. 8 oz (23.26 kg)

Tie Rod Nut

30 ft. lbs

48 ft. lbs

18 ft. lbs.

Enclosure Plug

Outlet Port Plugs

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MX Series

Dimensions

ꢀꢁꢇv/54,%4

ti11476

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MX Series

Parts

Ref Part No. Description

562514 VALVE, MX assembly 25S

562515 VALVE, MX assembly 25T

562516 VALVE, MX assembly 50S

562517 VALVE, MX assembly 50T

562538 VALVE, MX assembly 75S

562539 VALVE, MX assembly 75T

562540 VALVE, MX assembly 100S

562541 VALVE, MX assembly 100T

562542 VALVE, MX assembly 125S

562543 VALVE, MX assembly 125T

562545 VALVE, MX assembly 150S

562546 VALVE, MX assembly 150T

562528 VALVE, MX assembly 50S IND LH

562518 VALVE, MX assembly 50S IND RH

562533 VALVE, MX assembly 50T IND LH

562523 VALVE, MX assembly 50T IND RH

562529 VALVE, MX assembly 75S IND LH

562519 VALVE, MX assembly 75S IND RH

562534 VALVE, MX assembly 75T IND LH

562524 VALVE, MX assembly 75T IND RH

562530 VALVE, MX assembly 100S IND LH

562520 VALVE, MX assembly 100S IND RH

562569 VALVE, MX assembly 100T IND LH

562525 VALVE, MX assembly 100T IND RH

562531 VALVE, MX assembly 125S IND LH

562521 VALVE, MX assembly 125S IND RH

562535 VALVE, MX assembly 125T IND LH

562526 VALVE, MX assembly 125T IND RH

562532 VALVE, MX assembly 150S IND LH

562522 VALVE, MX assembly 150S IND RH

562536 VALVE, MX assembly 150T IND LH

562527 VALVE, MX assembly 150T IND RH

560620 BLOCK, inlet

563287 BLOCK, end

557488 ROD, tie, MX 3 (4 required)

557489 ROD, tie, MX 4 (4 required)

557490 ROD, tie, MX 5 (4 required)

557491 ROD, tie, MX 6 (4 required)

557492 ROD, MX 7 (4 required)

557493 ROD, tie, MX 8 (4 required)

560576 ROD, tie, MX 9 (4 required)

560577 ROD, tie, MX 10 (4 required)

557494 NUT, tie rod 3/8 - 24 lock (8 required)

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

MX Series

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Tube Clips

Mounting Brackets

Clips are plated and provided with 17/64” (6.75 mm)

mounting holes.

All mounting brackets include screws, lock washers and

nuts.

Part No. Description

557324 Holds 1 - 1/4” (6.35 mm) OD tube

558711 Holds 1 - 3/8” (9.52 mm) OD tube

558710 Holds 3 - 1/4” (6.35 mm) OD tube

563435 MSP and MH, M-3 and M-4, 1/8” (3.175 mm)

thick, top mounting.

563436 MSP and MH, M5 and M-6, 1/8” (3.175 mm)

thick, top mounting

563437 MSP and MH, M7 and M-8, 1/8” (3.175 mm)

thick, top mounting

Mounting Bars

563438 MSP and MH, M-3 and M-4, 1/8” (3.175 mm)

thick, side mounting.

563439 MSP and MH, M5 and M-6, 1/8” (3.175 mm)

thick, side mounting

563440 MSP and MH, M7 and M-8, 1/8” (3.175 mm)

thick, side mounting

Part No. Description

560920 MSP, 1/2” (12.7 mm) thick, 1/4-20 thread

561101 MJ, 1/2” (12.7 mm) thick, 10-24 thread

561102 MX and MXP, 1/2” (12.7 mm) thick, 5/16-18

threads, two sets of mounting holes

563465 KIT, mounting bar, includes 2 mounting bars,

4 screws, washers and lock washers

Performance Indicators

Performance indicators are pressure sensitive devices that signals a fault when there is excessive build up of pres-

sure in a series progressive lubricating system. A fault is identified by either causing a pin to protrude or by releasing

lubricant to the atmosphere.

Reset Indicator with Memory

Reset Indicators stop lube system operation when a fault occurs. They can be used in either master or secondary

divider valves. Fault is indicated when a pin protrudes through the opening in the cap and is manually reset.

Description

1/8” NPSF

w/O-Ring

MH, MS, MXP

Nickel Plated

1/8” NPTF

MJ, MH, MS, MXP

7/8” SAE

w/O-Ring

MGO

Pressure PSI

1/8” NPTF

MJ, MH, MS, MXP

1/4” NPTF

MX Only

250

500

750

1000

1500

2000

2500

3000

5000

563231

563232

563233

563234

563235

563236

563237

563252

563253

563254

563255

563256

563257

563258

563261

563262

563246

563247

563248

563249

563239

563240

563241

563242

563243

563244

563245

564200

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Automatic Relief Indicator

Automatic Relief Indicators pinpoint lube line blockage but allow the lube system to continue to supply lubrication to

points that are not blocked. They are used primarily in secondary divider valves. When needed, pressure is relieved

through a vent. When pressure is relieved the spring resets the piston. Because these indicators permit the lube sys-

tem to continue operating when a lube point is blocked, a separate pressure switch connected to an audible or visual

alarm should be used to warn of high pressure.

Description

1/8” NPSF

w/O-Ring

Pressure PSI

Color*

1/8” NPTF

1/4” NPTF

MX Only

MJ, MH, MS, MXP

MH, MS, MXP

750 + 20%

1000 + 20%

1250 + 20%

1500 + 20%

2000 + 20%

2500 + 20%

3000 + 24%

Blue

Green

Yellow

Red

Orange

Aluminum

Purple

563163

563164

563165

563166

563167

563168

563169

563170

563171

563172

563173

563174

563175

563176

563156

563157

563158

563159

563160

563161

* Color provided for reference only to aid in selection of replacement indicator. Indicators used to be

identified by the color of the spring retainer located in the end of the indicator.

Rupture Indicator - MH Divider Valves Only

Rupture Indicators are only used on MH divider valve applications where lube system pressures exceed 2500 psi.

The high pressure from a lube line blockage causes a disc to rupture. The lubricant then forces an indicator pin to

protrude, locating the blockage. The high pressure backs up through the system and trips a switch to shut the system

off. When the fault is corrected, the disc must be replaced the pin reset manually.

Description

1/8” - 27 NPSF

w/O-Ring

Replacement Disc

3/8” Diameter

Pressure PSI

1/8” - 27 NPTF

Disc Color

2800 + 20%

3700 + 20%

4600 + 20%

5500 + 20%

6400 + 20%

7300 + 20%

8200 + 20%

563228

563220

564355

563223

563225

563227

563229

563221

563222

563224

563226

Green

Yellow

Red

Orange

Pink

557422

557423

557424

557425

557427

557428

557429

Blue

Purple

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Rupture-to-Atmosphere Indicator

Rupture-to-Atmosphere Indicators are standard on all Graco pumps. When the pressure reaches a predetermined

pressure setting, the pressure disc ruptures, venting lubricant into the atmosphere and relieving pressure.

Description

Pressure PSI*

Complete Assembly

1/4” NPTF Fittings

Replacement

Disc Color

Blowout Disc

Quantity = 6

11/16” Diameter

900

563179

563182

563183

563184

557431

557433

557434

557435

557436

557467

557438

557439

Black

Yellow

Red

Orange

Aluminum

Pink

563962

563963

563964

563965

1450

1750

2050

2350

2650

2950

3250

563185

Blue

Purple

563966

1/8” NPTF Fittings

3/8” Diameter

Quantity = 25

900

564059

563191

563192

563193

563194

555788

557423

557424

557425

557426

557427

557428

557429

557430

Black

Yellow

Red

Orange

Aluminum

Pink

Blue

Purple

Brown

563952

563954

563955

563956

563957

563958

563959

563960

563961

1450

1750

2050

2350

2650

2950

3250

5000

High Pressure

1/8” NPTF Fittings

3/8” Diameter

Quantity = 25

3700

4600

5500

6400

7300

8200

9500

564479

563216

563217

563218

563219

557423

557424

557425

557427

557428

557429

Yellow

Red

Orange

Pink

Blue

Purple

Gray

563954

563955

563956

563958

563959

563960

Rupture-to-Atmosphere Indicator with Spud Assembly

A Spud Assembly is available to return vented lubricant to the reservoir by way of a tube. A high pressure switch is

recommended to provide an audible or visual warning alarm that height system pressure has occurred.

Description

Pressure PSI*

Complete Assembly

Replacement

Disc Color

1450

1750

2350

563186

563187

563188

557433

557434

557436

Yellow

Red

Aluminum

*All pressures have a tolerance of + 500 psi.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Rupture Discs

All discs are 11/16” diameter.

Description

Pressure PSI*

Single Disc

Disc Color

Quantity 6/package

900

557431

557432

557433

557434

557435

557436

557437

557438

557439

Black

Green

Yellow

Red

Orange

Aluminum

Pink

1175

1450

1750

2050

2350

2650

2950

3250

563962

563963

563964

563965

Blue

Purple

563966

*All pressures have a tolerance of + 500 psi.

Singling and Crossporting Bar Assemblies

Singling Kits externally convert a “T” (Twin Outlet) section to an “S” (Single Outlet) section.

Crossporting Kits externally combine the output of two (2) adjacent sections.

Part Numbers

90 Duro

Fluoroelastomer

O-Ring (plate

Type)

Gasket

Upper Seal Lower Seal

(Bar Type) (Bar Type)

Gasket

Valve Block

Mounting

Screw-Long

Divider

Single Kit

Right Side Left Side

O-Ring

MJ-SS

MSP

562915

563469

52916

562914

563469

52917

563525

562914

563470

52917

563524

563471

56e526

557359

557403

55711

55712

557722

557773

556514

555601

MS (Nickel)

MXP

MXP (Nickel)

MGO

Cycle Indicators

Cycle Indicators provide a means of visually monitoring lube flow thru the system.

The pin type cycles in and out when lubricant is flowing. Movement of the pin is caused by the piston (the two are

attached) so that when the piston moves the indicator pin in and out once, the entire divider valve has cycled.

Valve Series O-Ring Sealed

MS/MH

MX/MXP

MGO

563251

563260

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Cycle Counters - Part No.: 563444

The purpose of a cycle counter is to give assurance that the lubricant is flowing thru the system. Every “count” indi-

cates one complete cycle of the divider valve. Visual inspection and/or recording of counts provides a constant check

on the performance of your lubricant system and the pump. The Cycle Counter can be used on any MJ, MS, MH, MX

and MXP divider valve assembly.

Cycle Switches

The function of a Cycle Switch is to electrically give assurance that the lubricant is flowing through the system. Actu-

ated by a cycle pin, the switch can be wired to various controls.

NOTE: The cycle switch MUST be attached to a section that is equipped with a cycle indicator pin.

Part Numbers

Series Flo Divider Valves

MS/MH

MS (Nickel)

MXP

MGO

563272

563269

Cycle Switch and Bracket Assembly

SPDT

Electrical Ratings: 15 amps at 125, 250 and 480 VAC; 1/2 amp at 125 VDC, 1/4

amp at 250 VDC, 6.0 amp at 24 VDC Non-Inductive

Replacement Switch

557781

564357

557781

564357

557781

564537

557781

564357

557781

564537

557781

Cycle Switch and Bracket Assembly

DPDT

Electrical Ratings: 10 amps at 125 or 250 VAC; 0.3 amp at 125 VDC or 0.15 amp

at 250 VDC

Replacement Switch

Replacement Bracket for either

SPDT or DPDT Switch Assembly

Moisture Resistant Cycle Switch

with 6-foot Cable and Bracket

Assembly SPDT

560573

557546

563273

Electrical Ratings: 5 amps at 125 or 250 VAC; Wire Code for Moisture Resistant

Switch: BK (Com), Red (N.C), WH (N.O.), GN (Ground)

Replacement Switch with 6-foot

Cable

557782

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Proximity Cycle Switches

The Proximity Cycle Switches are magnetically operated single throw switches that sense the movement of the

divider valve piston when it is cycling. Each proximity cycle switch provides a signal that is used to monitor the sys-

tem. There are 3 different types of switches available.

Reed Type Proximity Switch: Can be used with oil applications only for MS, MH and MGO divider valves at pres-

sures up to 518 bar (7500 psi) at cycle rates under 60 cycles per minute.

Field Sensitive Magnetic Proximity Switch: Dry contact, ceramic magnet operated switch. Used at pressures that

do not exceed 242 bar (3500 psi) at cycle rates up to 200 cycles per minute. Used in MS/MH, MX/MXP and MGO

divider valves. An explosion proof version for MS/MH divider valves is available.

Magnetic Operated Proximity Switch: Not limited to valve size. Miniature snap-action switch is tripped by attraction

of internal magnet to the moving divider piston. Can be used at pressures up to 518 bar (7500 psi) at cycle rates that

do not exceed 150 cycles per minute.

Part Number

No.

of Pins

Type

Seal

Description

MXP

MGO

Unattached Reed Type (oil only)

1/2 NPT with

Leads

(Explosion

Proof)

10mA @ 120VAC

24 mA @ 24VDC

10,000,000 Cycle Life

O-Ring

563427

O-Ring

Gasket*

O-Ring

Gasket*

O-Ring

557741

557746

557741

557746

563476

564399

563476

564399

563970

563495

Field Sensitive Magnetic Type

3-pin and 5-pin (AC only)

2A @ 120/240 VAC

4-pin (DC only) 0.1A @ 28VDC

150,000,000 Cycle Life

557747

558939

Pigtail Lead

(Explosion

Proof)

O-Ring

557745

564401

Magnetic Type with LED’s

O-Ring

563478

563477

563478

563477

5A @ 24 VDC

10,000,000 Cycle Life

Gasket*

O-Ring

563484

563486

564400

563486

564400

Magnetic Type

5A @ 24VDC

5A @ 120/240 VAC

10,000,000 Cycle Life

Pigtail Lead

(Explosion

Proof)

O-Ring

563485

563500

563485

563501

Field Sensitive Magnetic Type

25 mA @ 24VDC

O-Ring

M12 x 1, 4-pin (DC only)

10,000,000, cycle life

*Consult your distributor for availability.

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Proximity Switch Connection Cables

Connection Cables for:

3-Pin Proximity Switch

5-Pin Proximity Switch

Connector Length - ft (m) Part No.

Connector Length - ft (m)

Part No.

558023

558024

558965

Straight

6 (1.83)

12 (3.66)

558021

558022

Straight

90°

6 (1.83)

12 (3.66)

6 (1.83)

4-Pin Proximity Switch

568738 NA

Straight

7 (2.13)

312497F

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in

material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty

published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written

recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty

installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of

non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with

structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or

maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of

the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned

to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will

be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or

consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to

the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these

warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or

the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the

negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,

given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la

rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite

de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 312497

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

www.graco.com

Revised 11/2011

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Baby Monitor 2755 User Manual
Groupe SEB USA T FAL Kitchen Grill CB6010 User Manual
Haier Freezer HF 240T User Manual
Hamilton Beach Toaster 22720 User Manual
Harbor Freight Tools Drill 36698 User Manual
Harbor Freight Tools Electric Heater 47906 User Manual
Hasbro Games 05949 User Manual
Hotpoint Double Oven DBS 537 X S User Manual
HP Hewlett Packard Scanner G4000 User Manual
Husqvarna Brush Cutter 3325 User Manual