Graco Marine Instruments 234414 User Manual

Instructions - Parts List  
2.5 and 5.0 Gallon  
Pressure Tank  
309926G  
- Not for use with highly abrasive, corrosive, or rust inducing materials -  
Model  
234414  
234415  
234416  
234417  
Capacity  
Regulation  
2.5 gal. (9.5 liter)  
2.5 gal. (9.5 liter)  
5 gal. (19 liter)  
5 gal. (19 liter)  
single  
dual  
single  
dual  
50 psi (345 kPa, 3.5 bar) Maximum Fluid Pressure*  
*Air pressure loads that are higher than design loads  
or alterations to the pressure feed tank, can result in  
tank rupture or explosion.  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441  
Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Set-Up  
Set-Up  
Pressure Relief Procedure  
Material Preparation  
Follow manufacturer’s directions for mixing and  
preparing material.  
WARNING  
Strain material using a fine mesh screen to prevent  
foreign matter from entering and clogging passageways.  
Pressure tanks remain pressurized until pressure is  
manually relieved. To reduce the risk of serious injury  
from pressurized fluid or accidental spray from gun,  
always follow this procedure to relieve pressure in the  
tank:  
Tank Assembly  
1. Install tank handle and lock nut by turning handle  
clockwise 4-5 turns. Position handle so it is parallel  
to safety valve branch tee.  
• Before you check or service any part of the spray  
system.  
• Before you loosen or remove the pressure tank  
cover or fill port.  
• Whenever you stop spraying.  
2. Secure in place by tightening lock nut using a 9/16  
in. open end wrench.  
Tank handle must be attached before installing  
regulator.  
1. Shut off air supply to the tank by closing air valve.  
2. Pull ring on safety valve until pressure bleeds down.  
3. Install regulator 234393 by tightening swivel adapter  
nut 288804 onto nipple 288778. Position unit so  
gauge is facing the same direction as safety valve  
ring. Use 11/16 in. open end wrench to tighten  
swivel adapter nut.  
309926G  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Installation  
WARNING  
3. Pour material into tank.  
Use part no. 289136 2.5 Gallon Disposable Tank  
Liners for easy clean-up. Not available for 5 Gallon  
Tank.  
• A safety valve protects tank from over pressuriza-  
tion. During each use, pull ring on safety valve to  
check if it operates freely and relieves air pressure.  
If the valve is stuck, does not operate freely, or does  
not relieve air pressure, it must be replaced.  
• Do not discard or make any alterations or substitu-  
tions to safety valve.  
• Do not make any changes to the pressure tank.  
Tampering in the form of drilling, welding, etc., will  
weaken the tank.  
4. Replace lid assembly and tighten clamps and thumb  
screws securely.  
5. Pass air supply line through Air Control Unit to filter  
dirt from air and extract water and oil. Connect air  
supply hose to air inlet fitting on tank regulator.  
6. Attach atomization air hose to the air outlet fitting  
which is directly opposite air inlet fitting on tank  
pressure regulator.  
The following information is for a typical  
installation.  
7. Connect material hose to fluid outlet fitting on top of  
tank lid.  
2. Slowly loosen thumb screws, tip lid clamps back and  
remove lid assembly.  
MADE IN USA  
971  
4
309926G  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
9. Pour solvent into tank.  
Operation  
10. Replace lid and tighten thumb screws and clamps.  
1. Turn on air supply.  
11. Turn T-handle on tank regulator clockwise while  
pulling gun trigger fully back and spray until clean  
solvent appears.  
2. Turn T-handle adjusting screw clockwise on the tank  
pressure regulator, while pulling the gun trigger fully  
back to start material flow.  
12. Repeat steps 1-3.  
3. Continue turning T-handle clockwise until desired  
material flow is achieved. To decrease pressure turn  
T-handle counter-clockwise to a lower setting. Then  
relieve pressure in tank by pulling the ring on the  
safety valve.  
Decorative powder coating may be affected by  
solvent contact. Avoid prolonged exposure of  
solvents to powder coated areas. Tank has been  
zinc plated underneath the decorative coating for  
rust protection.  
4. Atomization air for the spray gun can be adjusted  
using the air adjusting valve on the spray gun or at  
the air regulator assembly (Model 234415 only) on  
the pressure tank.  
5. Operate spray gun according to instructions  
accompanying gun.  
Maintenance  
Cleaning the Tank  
1. Turn off main air supply to tank.  
3. Turn T-handle adjusting screw on regulator,  
counter-clockwise until no spring tension is felt.  
4. Slowly loosen thumb screws, tip clamps back and  
tip tank lid to one side.  
5. Loosen spray gun air cap ring about three turns.  
6. Turn on air supply.  
7. Hold a cloth over air cap on gun and pull trigger.  
This forces material back through the hose, into the  
tank.  
8. Empty and clean tank and parts using a suitable  
solvent.  
309926G  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Troubleshooting  
Troubleshooting  
Problem  
Cause(s)  
Solution(s)  
Replace diaphragm  
Air escaping from the hose on regula- Broken or damaged diaphragm  
tor bonnet.  
Pressure creepage registered on  
gauge  
Dirty or worn valve seat in regulator Clean or replace valve seat  
Fluid or air leak at lid gasket  
Defective lid gasket or thumb screws Replace or tighten  
not tight  
Technical Data  
Maximum Fluid Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 50 psi (345 kPa, 3.5 bar)  
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4” nps  
Fluid Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8” nps  
Wetted Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PTFE-coated steel bowl, zinc-plated pick-up tube,  
nickel-plated fluid fitting  
6
309926G  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
Parts  
2.5 and 5 Gallon Pressure Tanks, Models: 234414,  
234415, 234416, 234417  
234393 Regulator  
Part No.  
Description  
Part No.  
Description  
160430  
288778  
289150  
289151  
289152  
289153  
289154  
288779  
289155  
288780  
289156  
289157  
289158  
289159  
289160  
GAUGE, fluid pressure  
NIPPLE, 1/4 in.  
REGULATOR, body  
REGULATOR, bonnet  
SEAT, valve  
SPRING, valve  
BODY, valve  
157350  
234393  
289134  
289141  
289144  
288803  
116306  
288804  
289161  
288805  
288806  
289145  
289146  
289147  
289148  
234392  
ADAPTER, 3/8 npt x 1/4 npt  
REGULATOR, air pressure  
TUBE fluid (234414 & 234415 only)  
TUBE, fluid (234416 & 234417 only)  
LID, assembly  
LID, gasket, thiokol  
VALVE, safety  
ADAPTER, swivel  
TEE, branch  
HANDLE, tank  
NUT, hex, handle  
NIPPLE, fluid, 3/8 in.  
ELBOW, street  
YOKE, assembly, with thumbscrew  
PIN, hinge with “E” clip  
REGULATOR, air pressure (234415 &  
234417 only)  
GAUGE, air pressure  
PLUG  
ADAPTER, 3/8npt x 1/4 npt  
STEM, valve  
SCREEN, wire  
DIAPHRAGM, assembly  
SPRING, pressure  
WASHER, spring  
DAMPER, vibration  
SCREW, adjusting  
SCREW  
Accessories  
289136  
160430  
289149  
157350  
TANK LINER, not shown (234414 and  
234415 only), 2.5 gal. only  
234415 & 234417  
additional components  
288805  
234393  
289159  
289160  
160430  
157350  
234392  
289151  
289149  
157350  
289157  
289156  
289158  
288806  
289146  
289145  
288804  
289161  
116306  
289147  
288780  
289154  
289152  
288779  
289144  
288803  
289148  
289153  
289134  
or  
289141  
289150  
289155  
Model 234414 shown  
309926G  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material  
and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by  
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be  
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance  
of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will  
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Phone Numbers  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 309926  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441  
309926G 6/2003, Rev. 9/2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Drill H7859 User Manual
Harbor Freight Tools Log Splitter 65076 User Manual
Hasbro Games Pushover User Manual
Hayter Mowers Lawn Mower RRS82H User Manual
Honeywell Home Security System 2 Partitioned Security System User Manual
Honeywell Portable Radio TE532ELW User Manual
Hotpoint Dishwasher HDA 467 User Manual
Hotpoint Ventilation Hood HHC67AB User Manual
HP Hewlett Packard Computer Drive Ultrium Drive User Manual
IBM Printer QMS 1725E User Manual