Instructions
Water-Jacket
Heated Hose Kit
309525G
EN
Part No. 245866
Includes parts needed to assemble heated hose system. Heated hose assembly and VISCON HP heater must be
ordered separately.
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
II 2 G
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
WARNING
ELECTRIC SHOCK HAZARD
Improper grounding, wiring, or usage of the system can cause electric shock.
•
All electrical wiring must be done by a qualified electrician and comply with all local codes and regu-
lations.
•
•
Connect only to grounded power source.
Turn off and disconnect power at the main switch before disconnecting any cables and before servic-
ing equipment.
EQUIPMENT MISUSE HAZARD
Misuse can cause serious injury or death.
•
•
•
•
•
•
For professional use only.
Use equipment only for its intended purpose. Call your Graco distributor for information.
Read manuals, warnings, tags, and labels before operating equipment. Follow instructions.
Check equipment daily. Repair or replace worn or damaged parts immediately.
Do not alter or modify equipment. Use only Graco parts and accessories.
Do not exceed the maximum working pressure or temperature rating of the lowest rated system
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings.
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
Comply with all applicable safety regulations.
•
•
•
BURN HAZARD
This equipment is used with heated fluid, which can cause equipment surfaces to become very hot. To
avoid severe burns:
•
•
•
Do not touch hot fluid or equipment.
Allow equipment to cool completely before touching it.
Wear heat protective gloves and take special care if fluid temperature exceeds 110° F (43° C).
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
•
Read Material Safety Data Sheets (MSDS) to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PERSONAL PROTECTIVE EQUIPMENT
You must wear proper protective equipment when operating, servicing, or when in the operating area of
the equipment to help protect you from serious injury, including eye injury; inhalation of toxic fumes: and
hearing loss. This equipment includes but is not limited to:
•
•
•
Protective eyewear
Gloves, clothing, and respirator as recommended by the fluid and solvent manufacturer
Hearing protection
309525G
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Heated Hose Components
Heated Hose Components
You need the following parts to install the heated hose system on the Xtreme Mix proportioner.
Heated Hose Kit 245866
The kit described in this manual, which includes all miscellaneous parts needed to assemble the system.
Heated Hose Assembly
Order separately a heated hose assembly that meets maximum pressure and hose diameter requirements. You can
connect up to six 50 ft. (15.2 m) heated hose sections for a maximum total length of 300 ft. (91.4 m).
A
B
A
B
C
D
Single Hose Assembly
Dual Hose Assembly
Single Hose Assemblies
Part No.,
Series
Maximum
Pressure Rating
psi (MPa, bar)
Hose Diameter
Thread A
Thread B
Approvals
in. (mm)
npt(m)
npsm(f)
245840, C
245841, C
245842, C
245843, C
245844, C
245845, C
5000 psi (34, 345)
7250 psi (50, 500)
5000 psi (34, 345)
7250 psi (50, 500)
5000 psi (34, 345)
7250 psi (50, 500)
1/4 (6.35)
1/4 (6.35)
3/8 (9.53)
3/8 (9.53)
1/2 (12.7)
1/2 (12.7)
1/4
1/4
3/8
3/8
1/2
1/2
1/4
1/4
3/8
3/8
1/2
1/2
II 2 G
Dual Hose Assemblies
Part No.,
Series
Maximum
Pressure Rating
psi (MPa, bar)
Hose Diameter
Thread
Thread
Thread
Thread
D
Approvals
A
B
C
in. (mm)
npt(m)
npsm(f)
npt(m)
npsm(f)
248118, C
248119, C
248120, C
7250 psi (50, 500)
7250 psi (50, 500)
7250 psi (50, 500)
1/2 (12.7)
3/8 (9.53)
A = 1/2 (12.7)
B = 3/8 (9.53)
1/2
3/8
1/2
1/2
3/8
1/2
1/2
3/8
3/8
1/2
3/8
3/8
II 2 G
248121, C
7250 psi (50, 500)
A = 3/8 (9.53)
B = 1/4 (6.35)
3/8
3/8
1/4
1/4
4
309525G
Download from Www.Somanuals.com. All Manuals Search And Download.
Heated Hose Components
Fluid Heater
Order separately a VISCON HP heater that meets local electrical and hazardous location requirements.
Hazardous Location Heaters
Part No.
245848
245863
245864
245862
246254
VAC (50/60 Hz single phase) / Watts / Amps
Approvals
Series
A
A
A
A
A
120 / 2300 / 19.2
240 / 4000 / 16.7
480 / 4000 / 8.30
See heater manual 309524 for approvals.
200 / 4000 / 20.0
380 / 4000 / 10.5
Non-hazardous Location Heaters
Model No.
245867
245868
245869
245870
246276
VAC (50/60 Hz single phase) / Watts / Amps
Approvals
Series
A
A
A
A
A
120 / 2300 / 19.2
200 / 4000 / 20.0
240 / 4000 / 16.7
480 / 4000 / 8.30
380 / 4000 / 10.5
See heater manual 309524 for approvals.
309525G
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Heated Hose Components
6
309525G
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
5
6
3, 7, 22, 25
10, 11, 15
1
B
17
10, 15, 23
12, 15
1
13, 15
1
16
24
14, 15
RED
BLUE
Resin Hose
14, 15
14, 15
C
Catalyst Hose
(optional installation)
14, 15
C
FIG. 1: Fluid and Air Line Connection Schematic
309525G
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
7. Interconnect reservoir tank (6), Husky 716 pump
Installing the Kit
(16), VISCON HP heater (B), and heated hose
(C-FIG. 1), using tubing (1), tube inserts (15) and fit-
tings (10, 12, 13, 14) as described below.
1. Mount pump (16) on the Xtreme Mix cart (D) using
the bracket (21), lockwashers (4), and nuts (2).
To ensure a leak-proof seal, use PTFE tape on all
pipe thread connections.
2. Mount VISCON HP heater (B-ordered separately)
on the cart using screws and lockwashers (A) sup-
plied with the heater, and the bracket (8), screws
(9), lockwashers (19), and nuts (20) supplied with
the kit.
a. Using tubing cutter (19), cut tubing (1) squarely
to desired lengths.
b. Insert tube inserts (15) in tubing (1) ends to
avoid leakage.
3. Connect nipple (22) and air regulator (7) to Husky
716 pump. Connect 100 psi (0.7MPa, 7 bar) air sup-
ply to the air regulator using air tubing (5), and air fit-
ting (3). Refer to Husky 716 manual if needed.
c. Insert tubing (1) through the back of the nut in
each of the plastic fittings (10, 12, 13, 14) until
the tube stops. Tighten the nut hand tight, then
tighten it 1-1/2 to 2 turns with a wrench.
The air regulator (7) controls pump (16) pressure.
Fitting nuts may need retightening as the system
reaches normal operating temperatures.
WARNING
Connecting Additional Hose Lengths
All wiring must be done by an electrician. See warn-
ings, page 2.
Up to six 50 ft. (15.2 m) sections of heated hose can be
attached for a maximum total length of 300 ft. (91.4 m).
4. Wire VISCON HP heater (B) to your voltage supply.
Follow wiring procedure in the VISCON HP manual.
1. Remove plastic u-turn fittings at the end of the
heated hose assembly. See FIG. 1.
5. Connect elbow (24), fitting (23), o-ring (17), and res-
ervoir tank (6) to Husky 716 pump (16). On other
side of pump, install bushing (11) and tube fitting
(10).
2. Connect the next length of hose, using union fittings
supplied with the hose. Follow fitting assembly pro-
6. Connect tube fittings (12, 13) to the VISCON HP
heater (B).
3. Tubes are color coded. Connect like colors.
8
309525G
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Each 50 ft. (15.2 m) heated hose section holds
approximately 1.25 gal. (4.7 liters) of fluid.
WARNING
3. Fill reservoir tank (6) about half full. Do not overfill;
fluid needs room to expand as the hose heats.
equipment.
4. Set the flow rate of the circulation fluid to 2 gpm (7.6
lpm) by adjusting the pump’s air regulator (7) until
the pump cycles at 50 cycles/min. Do not use a
higher flow rate as doing so will decrease system
performance and pump life. Never exceed the
hose’s 95 psi (0.6 MPa, 6.6 bar) maximum working
pressure rating.
1. Select fluid to use for heating circulation.
•
•
If ambient temperatures (storage or operating)
are below 40° F (4.4° C), a 50% water and 50%
antifreeze mixture is recommended.
5. Adjust the heater thermostat to the desired hose
temperature. The setting should be about 10° F
(6° C) higher than the desired paint temperature.
Never exceed the hose’s 180° F (82° C) maximum
temperature rating.
If ambient temperatures are above 40° F (4.4°
C), water alone is okay.
Detailed diaphragm pump operating instructions
are in Husky 716 manual.
If the hose is not being used for more than one
hour, shut off VISCON HP heater and Husky 716
pump to lengthen heater life.
2. Pour heating circulation fluid into the reservoir tank
(6), increase air regulator (7) pressure, and cycle
the pump (16). Continue to pour fluid into tank until
all air is purged.
10
309525G
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance
•
Check reservoir tank fluid level daily. Add fluid as
needed.
•
Follow heater maintenance instructions in VISCON
HP manual.
•
Follow pump maintenance instructions in Husky 716
manual.
Troubleshooting
Problem
Cause
Solution
Fluid leaking out of reservoir tank
when pump is turned off.
Tank overfilled.
Do not fill reservoir tank more than
half full.
Fluid fittings leaking.
Loose fittings.
Tighten fittings after system reaches
desired temperature.
Hose not heating to desired tempera- Diaphragm flow rate set too high.
Decrease diaphragm pump flow rate.
ture.
Problem with VISCON HP heater.
See troubleshooting in VISCON HP
heater manual.
Husky 716 pump not operating cor-
rectly.
See troubleshooting in Husky 716
pump manual.
Related Manuals
Refer to the following manuals for detailed equipment information.
Component Manuals
This manual available in following languages:
Manual
Description
Manual
Language
Manual
Language
309524
308981
309615
VISCON HP Heater
309525
309559
309560
309561
English
French
Spanish
German
309562
309588
309589
309590
Swedish
Chinese
Korean
Husky 716 Diaphragm Pump
Heater Bracket Kit
Japanese
309525G
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref.
Ref.
No. Part No. Description
Qty.
No. Part No. Description
Qty.
14** 117425 TEE; 1/2” (13 mm) OD tube
15** 117426 TUBE INSERT; 1/2” (13 mm) OD
tube
2
6
1*
---
TUBING; polyurethane; 1/2” (13
mm) OD; 10 ft. (3 m)
2
3
100015 NUT; 1/4-20 UNC-2B
C19391 ELBOW; 1/4 nptm x 1/4” (6.35
mm) OD tube
100016 LOCKWASHER
---
7
2
16
17
19
20
21
22
23
24
25
D53266 716 HUSKY PUMP
104938 O-RING; fluoroelastomer
106115 LOCKWASHER
100131 NUT; 3/8-16
15B337 BRACKET (pump)
156971 NIPPLE; 1/4 npt
15B338 FITTING
108307 ELBOW; 3/4 npt(m)
100139 PLUG, pipe
1
1
2
2
1
1
1
1
1
4
5*
7
TUBING; nylon; 1/4” (6.35 mm)
OD; 6 ft. (1.8 m)
6
188787 RESERVOIR TANK; 1.5 gal. (5.7
liter)
1
7
8
9
110147 AIR REGULATOR; 1/4 npt
15B336 BRACKET (heater)
110141 CAP SCREW; 3/8-16 x 1-1/2 in.
(13 mm)
1
1
2
*
Not available from Graco.
10
116316 FITTING; 1/2-14 npt x 1/2” (13
mm) OD tube
2
** If you are plumbing resin and catalyst hoses in par-
allel, purchase 4 additional tees (117425) and 12
additional inserts (117426).
11
12
117326 BUSHING; 3/4 npt(m) x 1/2 npt(f)
117423 ELBOW; 1/2 npt(m) x 1/2” (13 mm)
OD tube
117424 ELBOW; 1/2 npt(f) x 1/2” (13 mm)
OD tube
1
1
13
1
309525G
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TechnicalData
Technical Data
Maximum Working Pressure
High Pressure Fluid Hose . . . . . . . . . . . . . . . . . . . . . See Heated Hose Assembly table, page 4
Heated Fluid Circulation Components . . . . . . . . . . . . 95 psi (0.6 MPa, 6.6 bar)
Maximum Temperature Rating. . . . . . . . . . . . . . . . . . . . . 180° F (82° C)
Wetted Parts
High Pressure Fluid Hose . . . . . . . . . . . . . . . . . . . . . Nylon, Zinc-Plated Carbon Steel
Heated Fluid Circulation Tubes . . . . . . . . . . . . . . . . . Nylon
Heated Fluid Circulation Fittings . . . . . . . . . . . . . . . . Polypropylene, Aluminum, Brass, Zinc-Plated Carbon
Steel
Reservoir Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low Density Polyethylene
Heated Hose Dry Weight . . . . . . . . . . . . . . . . . . . . . . . . . 31 lb (14.1 kg)
14
309525G
Download from Www.Somanuals.com. All Manuals Search And Download.
Heated Hose Replacement Parts
Heated Hose Replacement Parts
Order the quantity required for your hose.
101
102
104
103
105
Ref.
Ref.
No. Part No. Description
No. Part No. Description
103 117461 FITTING; 1/2” (13 mm) OD tube
104 117426 TUBE INSERT; 1/2” (13 mm) OD tube
105 246456 HOSE COVER, protective; 50 ft. (15 m)
long
101 117423 ELBOW; 1/2 npt(m) x 1/2” (13 mm) OD
tube
102 117424 ELBOW; 1/2 npt(f) x 1/2” (13 mm) OD
tube
Accessory Scuff Jacket
Use to cover and protect heated hose.
85 ft. (25.9 m)
309525G
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material
and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance
of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 309525
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2002, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised 10/2011
Download from Www.Somanuals.com. All Manuals Search And Download.
|