308–505
INSTRUCTIONS-PARTS LIST
Rev
A
Supersedes
802–133 &
802–278
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS
READ AND RETAIN FOR REFERENCE
HYDRA-CLEANR 1535, 2040
Pressure Washer
P/N 800–165, Series B
P/N 800–367, Series A
1500 psi (103 bar) OPERATING PRESSURE
1900 psi (131 bar) MAXIMUM WORKING PRESSURE
P/N 800–164, Series C
P/N 800–290, Series B
2000 psi (138 bar) OPERATING PRESSURE
2400 psi (165 bar) MAXIMUM WORKING PRESSURE
GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 1989, GRACO INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT MISUSE HAZARD
General Safety
System Pressure
Any misuse of the pressure washer or accessories,
such as overpressurizing, modifying parts, using
incompatible chemicals and fluids, or using worn or
damaged parts, can cause them to rupture and result in
fluid injection, splashing in the eyes or on the skin, or
other serious bodily injury , fire, explosion or property
damage.
This sprayer can develop high operating pressures. Be
sure that all spray equipment and accessories are rated
to withstand the maximum working pressure of this
sprayer. DO NOT exceed the maximum working
pressure of any component or accessory used in the
system.
Chemical Compatibility
NEVER alter or modify any part of this equipment; doing
so could cause it to malfunction.
BE SURE that all chemicals used in the chemical
injector are compatible with the wetted parts of the hose,
gun, wand and tip, as given in the Technical Data (inside
back cover). Always read the chemical manufacturer’s
literature before using any chemical in this pressure
washer.
CHECK all spray equipment regularly and repair or
replace worn or damaged parts immediately
.
ALWAYS wear protective eyewear and appropriate
clothing. If using a chemical injector, read and follow the
chemical manufacturer
recommendations on additional protective equipment,
such as a respirator
’s literature for
.
HOSE SAFETY
High pressure fluid in the hoses can be very dangerous.
If the hose develops a leak, split or rupture due to any
kind of wear , damage or misuse, the high pressure
spray emitted from it can cause a fluid injection injury or
other serious bodily injury or property damage.
NEVER use a damaged hose. Before each use, check
entire hose for cuts, leaks, abrasion, bulging cover , or
damage or movement of the hose couplings. If any of
these conditions exist, replace the hose immediately .
DO NOT try to recouple high pressure hose or mend it
with tape or any other device. A repaired hose cannot
contain the high pressure fluid.
ALL FLUID HOSES MUST HA VE STRAIN RELIEFS
ON BOTH ENDS. The strain reliefs help protect the
hose from kinks or bends at or close to the coupling,
which can result in hose rupture.
HANDLE AND ROUTE HOSES CAREFULLY. Do not
pull on hoses to move the pressure washer. Do not use
chemicals which are not compatible with the inner tube
and cover of the hose. DO NOT expose Graco hose to
TIGHTEN all fluid connections securely before each
use. High pressure fluid can dislodge a loose coupling or
allow high pressure spray to be emitted from the
coupling.
temperatures above 200_ F (93_ C) or below –40_
F
(–40_ C).
FUEL AND EMISSION HAZARDS
NEVER fill the fuel tank while the unit is running or hot.
The fuel used in this unit is combustible and when spilled
on a hot surface can ignite and cause a fire. ALWAYS fill
tank slowly to avoid spilling.
NEVER alter the throttle setting, which is factory set.
Tampering with this adjustment can damage the
pressure washer and will void the warranty
.
NEVER operate the unit in a
closed building. The
exhaust contains carbon monoxide, a poisonous,
odorless, invisible gas which can cause serious injury or
death if inhaled.
3
308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers or other
body parts. KEEP CLEAR of moving parts when starting
Pressure Relief Procedure before checking or
servicing the pressure washer to prevent discharging
high pressure fluid from the gun.
or operating the pressure washer
.
NEVER operate the pressure washer without all guards
and interlocks installed and functioning. Follow the
TERMS
WARNING: Alerts user to avoid or correct conditions
NOTE: Identifies helpful procedures and information.
that could cause bodily injury
.
CAUTION: Alerts user to avoid or correct conditions
that could cause damage to or destruction of equipment.
IMPORTANT
United States Government safety standards have been adopted under the Occupational Safety and Health Act. These
standards—particularly the General Standards, Part 1910, and the Construction Standards, Part 1926—should be
consulted.
308-505
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
QUICK
COUPLER
2040
SPRAY
GUN
QUICK
COUPLER
HIGH
PRESSURE
HOSE
CONNECTION
INLET WATER
CONNECTON 3/4”
GARDEN HOSE
SPRAY
HOSE
1535
HIGH PRESSURE
HOSE CONNECTION
INLET WATER CONNECTON
3/4” GARDEN HOSE
Figure
1
Check for Shipping Damage
The unit should be checked for any damage that may
have occurred in shipping. Any damage should be noted
Connect to Water Supply
CAUTION
Before attaching to the water supply , check
your local plumbing code regarding cross–
connection to the water supply . A backflow
preventer P/N 801–133 is available to prevent
backflow of contaminated water into the fresh
water supply. Install it upstream from the pump.
and the carrier notified immediately
.
Set Up
If you are using a downstream chemical injector, install it
between the pump unloader and the high pressure
hose, using the quick couplers provided.
If inlet water pressure is over 60 psi (4.1 bar) a
regulating water valve P/N 800–258 must be
installed at the garden hose connection.
Connect the high pressure hose between the pump
outlet and the gun inlet. Both of these connections are
made with quick couplers.
Do not exceed 160_ F (70_ C) inlet water
CAUTION
temperature.
Up to 100 ft (30 m) of high pressure hose may
be used. Longer hoses may af fect sprayer
performance, and chemical injector
performance, if used.
Connect a hose with at least a 3/4 inch (19 mm) ID from
the water supply to the unit’s 3/4 inch garden hose inlet.
The supply hose should not be more than 50 ft (15 m)
long.
Install the appropriate spray tip on the wand. See
Installing and Changing Spray Tips. If you are using a
sandblaster kit, see its separate manual for installation
instructions.
NOTE: The water source at the unit
must have a
minimum flow rate equal to that of the unit (see
Technical Data, inside back cover).
5
308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTUP
Use this procedure whenever starting the pressure
washer to help insure that the unit is ready to operate
If the engine is cold, completely close the engine
choke. Grasp the starter rope, brace one foot on the
pressure washer chassis and pull rope rapidly and
firmly. Continue holding the rope as it returns. Pull
and return the rope until the engine starts. In cool
weather, the choke may have to be kept closed for
10 to 30 seconds before opening it to keep the
engine running. Otherwise, open the choke as soon
as the engine starts.
and starting is done safely
.
1. Check oil levels.
Engine: Add SAE 30 or 10W–30 weight detergent
oil as necessary
.
Pump: Add SAE 20 or 30 weight non–detergent oil
as necessary
.
If the engine is warm, leave the choke open, or just
partly close it. Start the engine as described in the
preceding paragraph. When it starts, be sure to
NOTE: Some units are equipped with a low–oil sensor
that shuts the engine of f if the oil level falls
open the choke completely
.
below a certain level. If the unit
stops
CAUTION
unexpectedly, check both the oil and the fuel
levels. Check the oil level each time the unit is
refueled.
On recoil start engines, never let the starter
rope return by itself. It could jam the recoil
system.
2. Check fuel level.
7. ALWAYS engage the gun’ s trigger safety latch
whenever you stop spraying, even for a moment, to
reduce the risk of fluid injection or splashing in the
eyes or on the skin if the gun is bumped or triggered
accidentally.
WARNING
DO NOT refuel a hot engine. Refueling a hot
engine could cause a fire. Use only fresh, clean
regular or unleaded gasoline. Close the fuel
shutoff valve during refueling.
8. ALWAYS observe the following
CAUTIONS to
avoid costly damage to the pressure washer
.
3. Turn on the water supply
.
CAUTION
DO NOT allow the pressure washer to idle for
more than 10 minutes. Doing so may cause the
recirculating water to overheat and seriously
damage the pump. T urn of f the pressure
washer if it will not be spraying or cleaning at
least every 10 minutes. If heated inlet water is
CAUTION
Never run the unit dry . Costly damage to the
pump will result. Always be sure the water
supply is completely turned on before
operating.
used, reduce this time further
.
4. Trigger the gun until water sprays from the tip
indicating that the air is purged from the system.
DO NOT run the pump dry, which will quickly
damage the pump. Be sure the water supply is
fully turned on before starting the pump.
5. Open the fuel shutoff valve and be sure the spark
plug ignition cable is pushed firmly onto the spark
plug. On those units equipped with an ignition
shutoff switch, the switch should be in the “on”
position. Throttle should be in the “run” position.
DO NOT operate the pressure washer with the
inlet water screen removed. This screen helps
keep abrasive sediment out of the pump, which
could clog or scratch the pump. Keep this
screen clean.
6. Start the engine.
NOTE: For easier starting, have one person start the
pressure washer while another person
triggers the spray gun.
DO NOT pump caustic materials; such
materials may corrode the pump components.
9. See the chemical injector or sandblaster kit manual
for detailed cleaning information if these
accessories are used.
308-505
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Trigger Safety Latch
WARNING
Installing and Changing Spray Tips
WARNING
To reduce the risk of serious bodily injury
,
To reduce the risk of serious bodily injury
,
including fluid injection, splashing in the eyes or
on the skin, ALWAYS engage the trigger safety
latch whenever spraying stops, even for a
moment.
including fluid injection or splashing in the eyes
or onto the skin, use extreme caution when
changing spray tips.
procedure below
ALWAYS follow the
.
In the engaged position, the trigger safety latch
prevents the gun from being triggered
1. Follow the Pressure Relief Procedure
.
accidentally by hand or if it is dropped or
bumped. Be sure the latch is pushed fully down
when engaging it or it cannot prevent the gun
from being triggered. See Figure 2.
2. Point the gun and wand away from yourself and
anyone else.
3. Without holding your hand over the spray tip (A), pull
back the quick coupler ring (B). Remove the old tip
and/or install a new one, and then release the ring.
See Figure 3.
4. Be sure the tip is secure before starting to spray
again.
5. Tip holding holes are provided on the chassis.
CAUTION
To avoid blowing the o–ring out of the quick
coupler, due to the high pressure in the system,
never operate the pressure washer without a tip
securely mounted in the quick coupler
.
TRIGGER SAFETY LATCH SHOWN ENGAGED
A
B
TRIGGER SAFETY LATCH SHOWN
DISENGAGED
Figure 2
Figure 3
7
308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
SHUTDOWN, FLUSHING AND STORAGE
MAINTENANCE
Observing regular maintenance intervals helps ensure
that you get maximum performance and life from the
WARNING
pressure washer
.
PRESSURE RELIEF PROCEDURE
To reduce the risk of serious bodily injury
including fluid injection and splashing in the
eyes, or on the skin, always follow this
procedure whenever you stop spraying for
more than 10 minutes, when shutting down,
,
There is a break–in period for the engine, pump and
gear reducer (if used). After changing the oil in these
components following their respective break–in periods,
the interval between required changes is longer
.
and before checking or repairing any part of the
system.
If the unit is operating in dusty conditions, these
maintenance checks should be made more often.
1. Engage the trigger safety latch.
2. Turn the sprayer off.
WARNING
To reduce the risk of serious bodily injury
including fluid injection, splashing in the eyes or
on the skin or injury from moving parts, always
Pressure Relief Procedure
Warning before proceeding.
,
3. Remove the ignition cable from the spark
plug.
follow the
4. Shut off the water supply
.
5. Disengage the trigger safety latch and
trigger the gun to relieve pressure, and then
engage the trigger safety latch again.
Interval
What to do
Daily
Clean water inlet screen and
filter. Check engine and pump oil
levels. Fill as necessary. Check
6. Before long–term (overnight) storage or
transporting of unit, disconnect the water
supply, and turn off the fuel supply valve.
gasoline level. Fill as necessary
.
After first 5
hours of
operation
Change engine break–in oil.
Drain oil when warm. Use SAE
30 or 10W–30 detergent oil.
1. If the pressure washer will be exposed to freezing
temperatures, drain all water out of the pump. If it
must be stored in freezing temperatures, flush the
unit with a 50% anti–freeze solution. Relieve
pressure. Flush the pressure washer before using it
again to remove the anti–freeze.
Each 25 hours
of operation
Clean and remove air cleaner
foam. Wash with water and
detergent. Dry thoroughly. Rub
with oil and squeeze to distribute
oil.
After first 50
hours of
operation
Change pump break–in oil. Use
SAE 20 or 30 non–detergent oil.
Change gear reducer oil. Use
SAE 90 gear oil.
NOTE: An anti–freeze flush kit P/N 802–327 is
available to make flushing easier
.
CAUTION
Each 100 hours
of operation
or 3 months
Clean or replace paper air
cleaner cartridge. Tap gently to
remove dirt. Change engine oil.
Use SAE 30 or 10W–30
detergent oil.
If water does freeze in the pressure washer ,
thaw it in a warm room before trying to start it.
DO NOT pour hot water on or into the pump; it
may crack the ceramic plungers!
Each 500 hours
of operation
or 6 months
Change pump oil. Use SAE 20
or 30 non–detergent oil. Change
gear reducer oil. Use SAE 90
gear oil.
2. After each use, wipe all surfaces of the pressure
washer with a clean, damp cloth.
3. Perform the appropriate maintenance.
maintenance chart.
See
308-505
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING CHART
WARNING
To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin or
injury from moving parts, always follow the Pressure Relief Procedure Warning before proceeding.
CAUSE
SOLUTION
PROBLEM
Engine will not start or No gasoline in fuel tank or carburetor
.
Fill the tank with gasoline, open fuel shut off valve.
Check fuel line and carburetor.
is hard to start
Low oil (on units with low oil sensor).
Start/Stop switch in Stop position.
Add to proper level.
Move switch to start position.
W
ater in gasoline or old fuel.
Choked improperly. Flooded engine.
Dirty air cleaner filter
Drain fuel tank and carburetor. Use new fuel and dry
spark plug.
Open choke and crank engine several times to clear
out gas.
.
Remove and clean.
Spark plug dirty, wrong gap or wrong type.
Spray gun closed.
Clean, adjust the gap or replace.
Trigger spray gun.
Engine misses or
lacks power
Partially plugged air cleaner filter
Spark plug dirty, wrong gap or wrong type.
orn or wrong size tip.
Inlet filter clogged.
orn packings, abrasives in water or
natural wear
Inadequate water supply
.
Remove and clean.
Clean, adjust the gap or replace.
Replace with tip of proper size.
Low pressure and/or
pump runs rough
W
Clean. Check more frequently
.
Check filter. Replace packings. See PUMP SERVICE.
W
.
Check water flow rate to pump.
.
Clean inlet and discharge valve assemblies. Check
filter.
Fouled or dirty inlet or discharge valves.
Even a small particle can cause the valve
to stick.
Check garden hose, may be collapsed or kinked.
Replace worn valves.
Restricted inlet.
W
orn inlet or discharge valves.
Leaking high pressure hose.
orn packings.
Replace high pressure hose.
W
ater leakage from
W
Install new packings. See PUMP SERVICE.
under pump manifold
Water in pump
Humid air condensing inside crankcase.
orn packings.
Oil seals leaking.
Change oil as specified in MAINTENANCE.
Install new packings. See PUMP SERVICE.
Install new oil seals. See PUMP SERVICE.
W
Frequent or premature Scored, damaged or worn plungers.
failure of the packings
Install new plungers. See PUMP SERVICE.
Abrasive material in the fluid being pumped. Install proper filtration on pump inlet plumbing.
Inlet water temperature too high.
Overpressurizing pump.
Check water temperature; may not exceed 160_F.
Do not modify any factory–set adjustments. See
EQUIPMENT MISUSE HAZARD.
Excessive pressure due to partially plugged Clean or replace tip. See Installing and Changing
or damaged tip.
Spray Tips.
Pump running too long without spraying.
Never run pump more than 10 minutes without
spraying.
Running pump dry
.
Do not run pump without water.
Strong surging at the
Foreign particles in the inlet or discharge
Clean or replace valves. See PUMP SERVICE.
inlet and low pressure valve or worn inlet and/or discharge valves.
on the discharge side
Oil leakage between
the gear reducer cover
and case
W
W
W
orn gasket.
Replace the gasket. See SERVICE SECTION.
Oil leakage between
the gear reducer cover
and the pump
orn oil seals and/or o-ring.
orn oil seal.
Replace oil seals and/or o-ring. See SERVICE
SECTION.
Oil leakage between
the gear reducer case
and the engine
Replace oil seal. See SERVICE SECTION.
9
308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DRAWING
800–164 & 800–290 Hydra–Cleanr 2040 Pressure Washer
3
4
4
5
2
3
7
5
50
7
50
43
8
9
66
65
41
8
9
38
45
65
46
51
47
59
44
28
49
48
52
51
53
11
9
65
55
13
57
60
61
56
58
54
37
39
40
12
35
36
15
16
1
13
34
11
27
9
65
65
19
29
17
33
42
18
6
49
24
20
21
15
16
20
22
26
25
13
15
16
62
26
23
14
30
32
64
10
31
63
26
25
26
308-505 10
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
800–164 & 800–290 Hydra–Cleanr 2040 Pressure Washer
REF PART
NO. NO.
REF
PART
DESCRIPTION
QTY
NO. NO.
DESCRIPTION
QTY
1
4
1
800–394 GUN & WAND ASSEMBL
Y
33
34
35
800–176 CHASSIS
(incl. 15, 17, 19, 27, 49)
802–257 GUARD, Muffler, Briggs &
Stratton
802–367 LABEL, Identification, 2040
802–363 LABEL, Caution
802–368 LABEL, Identification, 2040
179–885 LABEL, Warning, chassis
1
801–548 GROMMET, Rubber
2
800–173 TIP ASSEMBL , 15 Degree
Y
1
1
1
1
1
(incl. 13, 39)
800–174 TIP ASSEMBL
(incl. 13, 40)
1
3
4
5
6
36
Y
, 0 Degree
1
1
1
1
1
1
1
37
38
39
40
41
42
43
402–278 PLUG, Plastic
803–083 LABEL, Keep From Freezing
801–729 TIP, Spray 15 Degree
801–730 TIP, Spray 0 Degree
7 * 802–141 ENGINE, 8 hp, Briggs &
Stratton I/C
1
1
h
802–998 ENGINE, 8 hp, Honda OHV
802–127 SCREW, Cap, hex hd.
5/16–18 x 1-3/4
801–025 WASHER, Lock 5/16
800–374 HOSE ASSEMBL
(incl. 13, 14, 15)
801–024 NUT, Hex 5/16–18
801–539 BUMPER
801–090 COUPLER, Male 1/4
801–007 HOSE, High Pressure, 50’
801–009 COUPLER, Female 1/4 (incl. 16)
801–202 O–RING, Female Coupler 1/4
803–350 GUN, Spray
801–941 SCREW, Cap, hex hd.
5/16–18 x 1
801–935 WAND, 20”
801–235 WASHER, Flat 5/8
801–880 PIN, Cotter 1/8 x 1-1/2
104–811 HUB CAP
106–062 WHEEL & TIRE ASSEMBL
802–139 AXLE
801–546 SCREW, Cap, hex hd.
3/8–16 x 1-1/4
801–015 WASHER, Flat 3/8
801–957 SLEEVE, 18”
803–405 PUMP ASSEMBL
(see page 18)
801–541 HANDLE
800–175 FRONT LEG ASSEMBL
(incl. 25, 26, 62, 63, 64)
801–363 WASHER, Lock 3/8
801–878 NUT, Hex 3/8–16
802–143 GEAR REDUCER (see page 17)
181–867 LABEL, Warning, ventilation
802–299 PUMP & GEAR REDUCER
ASSEMBLY (incl. 28, 41)
801–709 PLUG, Square hd. 1/4
801–907 WASHER, Flat
801–905 ADAPTER, 3/8 G x 3/8 NPT
801–868 NIPPLE, Hex 3/8
802–315 UNLOADER, 2000 psi
801–103 NIPPLE, Hex 3/8 x 1/4
801–137 KEY, Square 1/4 x 2
802–124 HOSE, Bypass (incl. 59)
801–523 NIPPLE, 1/2 x 2
8
4
10
9
10
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
Y, w/Couplers
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
1
6
1
4
1
3
3
1
11
12
13
14
15
16
17
18
801–622 CROSS, 1/2
800–115 VALVE, Thermal Relief
800–113 FILTER
4
1
4
2
2
2
1
19
20
21
22
23
24
25
801–111 NUT, Garden Hose
801–110 ADAPTER, Garden Hose
801–112 STRAINER, Garden Hose
802–627 NIPPLE, Hex 3/8 NPSM x
1/4 NPT
801–367 BUMPER, Rubber
802–140 BRACKET, Support
801–499 NUT, Lock 3/8–16
801–504 BUMPER, Rubber
801–858 BRACKET, Front Leg
801–023 WASHER, Flat 5/16
Y
1
2
60
61
62
63
64
65
5
6
1
1
26
27
28
1
1
Y, 2000 psi
1
1
1
14
4
29
30
66 * 100–078 SCREW, Cap, hex hd.
Y
1
4
4
31
32
*
Model 2040 (800–164)
Model 2040 (800–290)
h
11 308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DRAWING
800–165 & 800–367 Hydra–Cleanr 1535 Pressure Washer
30
3
33
30
4
33
4
5
43
5
59
59
25
20
21
17
6
7
8
8
7
6
3
47
50
46
51
44
58
45
31
49
48
41
6
7
8
50
9
13
54
9
55
42
22
23
56
52
57
26
27
24
53
11
12
1
28
6
7
8
29
19
32
15
16
8
18
49
34
8
11
12
16
35
17
9
8
11
12
2
37
17
36
10
39
37
40
14
38
308-505 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
800–165 & 800–367 Hydra–Cleanr 1535 Pressure Washer
REF PART
NO. NO.
REF
PART
DESCRIPTION
QTY
NO. NO.
31 h 803–245 GUARD, Muffler, Briggs &
32
33
34
35
DESCRIPTION
QTY
1
800–394 GUN & WAND ASSEMBL
Y
(incl. 11, 28, 29, 32, 49)
179–885 LABEL, Warning, chassis
802–366 LABEL, Identification, 1535
802–373 LABEL, Identification, 1535
1
1
1
1
1
Stratton
1
1
1
1
2
3
4
803–350 GUN, Spray
181–867 LABEL, Warning, ventilation
801–504 BUMPER, Rubber
801–546 SCREW, Cap, hex hd.
3/8–16 x 1-1/4
5 * 802–264 ENGINE, 5 hp, Honda OHV
h
803–239 ENGINE, 5 hp, Briggs &
Stratton I/C
801–024 NUT, Hex 5/16–18
801–025 WASHER, Lock 5/16
801–023 WASHER, Flat 5/16
801–090 COUPLER, Male 1/4
801–007 HOSE, High Pressure, 50’
1
1
4
2
2
2
1
4
1
8
8
8
4
1
3
3
1
36
37
38
39
40
41
42
43
802–273 AXLE
801–235 WASHER, Flat 5/8
6
7
8
9
10
11
12
13
14
106–062 WHEEL & TIRE ASSEMBL
801–880 PIN, Cotter 1/8 x 1-1/2
104–811 HUB CAP
802–267 BRACKET, Support
801–012 GROMMET, Rubber
802–300 PUMP & GEAR REDUCER
ASSEMBLY (incl. 20, 21)
801–709 PLUG, Square hd. 1/4
801–868 NIPPLE, Hex 3/8
801–905 ADAPTER, 3/8 G x 3/8 NPT
801–907 WASHER, Flat
802–316 UNLOADER, 1500 psi
801–103 NIPPLE, Hex 3/8 x 1/4
802–124 HOSE, Bypass (incl. 58)
801–523 NIPPLE, 1/2 x 2
801–622 CROSS, 1/2
800–115 VALVE, Thermal Relief
800–113 FILTER
Y
801–009 COUPLER, Female 1/4 (incl. 12)
801–202 O–RING, Female Coupler 1/4
800–184 HANDLE
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
800–374 HOSE ASSEMBLY, w/Couplers
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
(incl. 9, 10, 11)
801–499 NUT, Lock 3/8–16
801–015 WASHER, Flat 3/8
1
1
2
15
16
17
802–277 SCREW, Cap, hex hd.
5/16–18 x 2-1/2
802–127 SCREW, Cap, hex hd.
5/16–18 x 1-3/4
802–269 CHASSIS
802–266 GEAR REDUCER (see page 15)
6
18
2
1
1
19
20
21
802–265 PUMP ASSEMBL
Y
, 1500 psi
(see page 20)
1
1
801–111 NUT, Garden Hose
801–110 ADAPTER, Garden Hose
801–112 STRAINER, Garden Hose
802–627 NIPPLE, Hex 3/8 NPSM x
1/4 NPT
22
23
800–173 TIP ASSEMBL
Y
, 15 Degree
(incl. 9, 26)
800–174 TIP ASSEMBL
Y
, 0 Degree
(incl. 9, 27)
1
1
1
1
1
1
1
1
1
1
24
25
26
27
28
29
30
402–278 PLUG, Plastic
59
801–137 KEY, Square 1/4 x 2
803–083 LABEL, Keep From Freezing
801–729 TIP, Spray 15 Degree
801–730 TIP, Spray 0 Degree
801–957 SLEEVE, 18”
801–935 WAND, 20”
802–363 LABEL, Caution
h
Model 1535 (800–367)
Model 1535 (800–165)
*
13 308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
GEAR REDUCER SERVICE (1535)
WARNING
To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin or injury
from moving parts, always follow the Pressure Relief Procedure Warning on page 2 before proceeding.
Replacing the O–Ring
Replacing the Oil Seal
1. Remove the four bolts and lockwashers, and the
four washers, bumpers, and bolts. Then pull the
pump and gear reducer assembly off the engine.
NOTE: The oil seal MUST be replaced if removed.
1. Follow steps 1 and 2 under Replacing the O–Ring.
2. Drain the gear reducer oil by placing a container
under it and removing the drain plug with a 22 mm
wrench. Replace the o–ring if damaged.
2. Pry the oil seal out of the gear case. Be careful not to
damage the gear case.
3. Wipe the inner surface of the gear case clean, then
lightly coat it with grease. Place the oil seal into the
gear case. Use a socket, placed against the surface
of the seal, to push the seal into the case until its top
surface is past the ridge in the bore.
3. Remove the four screws and lockwashers with a
6 mm wrench and pull the gear case of f the gear
cover.
4. Remove the old o–ring. Clean the gear cover and
case surface. Lightly coat the new o–ring with
grease and install it in the gear case.
4. Follow steps 4 through 6 under Assembling the
Gear Reducer if this is all the service required.
5. Follow steps 4 through 6 under Assembling the
Gear Reducer if this is all the service required.
Assembling the Gear Reducer
1. Make sure the gasket is properly placed on the gear
cover. Refer to step 4 under Replacing the Gasket.
Then, install the gear cover on the pump shaft.
Replacing the Gasket
1. Follow steps 1 through 3 under Replacing the
O–Ring.
2. Align the holes in the gear cover with the holes in the
pump. Apply low strength Loctite r (blue) on the
screw threads and secure the cover with the four
screws and lockwashers. Tighten them oppositely
2. Using a 4 mm wrench, loosen the setscrew and pull
the gear off the pump with a gear puller
.
and evenly
.
3. Remove the four screws and lockwashers from the
gear cover
.
3. Align the gear
’s slot with the key on the pump shaft
and slide the gear onto the shaft, up to the pump’s
4. Remove the gear cover and gasket from the pump.
Clean the gear cover and pump surface. Lightly coat
both sides of the gasket with grease and install it on
shoulder. Apply low strength Loctite
r on the
setscrew threads and tighten the setscrew to lock
the gear on the shaft.
the gear cover
.
4. Make sure the o–ring is in place. Refer to step 4
under Replacing the O–Ring. Install the gear case
on the cover, aligning the holes, and secure it with
the four screws and lockwashers. T ighten them
5. Follow the instructions under Assembling the Gear
Reducer if this is all the service required.
oppositely and evenly
.
5. Grease the engine shaft. Align the gear ’s slot with
the key on the engine shaft and slide the gear
reducer onto the shaft, up to the engine’s shoulder
.
6. Secure the gear reducer to the engine with the four
bolts and lockwashers.
308-505 14
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DRAWING
802–266 Gear Reducer (1535)
10
6
11
9
8
12
13
14
7
19
3
20
16
15
17
5
8
18
4
2
1
PARTS LIST
802–266 Gear Reducer (1535)
REF PART
NO. NO.
DESCRIPTION
QTY
1
1
2
802–350 GASKET
802–351 COVER, Mounting
802–334 SCREW, Set
802–352 GEAR, Pump
802–353 O–RING
1
3
1
4
1
5
1
6
801–659 DIPSTICK
1
7
802–354 CASE, Mounting
801–023 WASHER, Lock
802–342 SCREW
1
8
8
9
4
10
11
12
13
14
15
16
17
18
19
20
802–355 SEAL, Oil
1
802–356 RING, Snap
802–357 RING, Snap
802–358 BEARING
1
1
1
802–359 GEAR, Engine
801–484 CAP, G 3/8 BSP
802–344 O–RING
1
1
1
802–345 GAUGE, Sight
802–331 BOLT, 5/16–24 x 1”
802–360 SCREW
1
4
4
801–139 WASHER, Lock
4
15 308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
GEAR REDUCER SERVICE (2040)
WARNING
To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin or injury
from moving parts, always follow the Pressure Relief Procedure Warning on page 2 before proceeding.
Replacing the Gasket
Replacing the Oil Seal
NOTE: To maintain a good seal, the gasket must be
replaced whenever the gear reducer is
disassembled.
NOTE: The oil seal MUST be replaced if removed.
1. Follow steps 1 and 3 under Replacing the Gasket.
2. Remove the snap ring from the gear case, using a
snap ring pliers. Pull the gear and bearing.
1. Remove the four bolts and lockwashers, washers
and pull the pump and gear reducer assembly of f
the engine.
3. Push the seal from the inside to the outside of the
gear case by placing screwdriver against the seal
2. Drain the gear reducer oil by placing a container
under it and removing the drain plug with a 22 mm
wrench. Replace the o–ring if damaged.
and lightly tapping it with hammer
.
4. Wipe the inner surface of the case clean, then lightly
coat it with grease. Place the oil seal into the gear
case. Use a socket, placed against the surface of
the seal, to push the seal into the case until its top
surface is past the ridge in the bore.
3. Remove the nine screws with a 6 mm wrench and
pull the gear case off the gear cover
.
4. Remove the old gasket. Clean the gear cover and
case surface. Lightly coat the new gasket
grease and install it in on the gear case.
with
5. Place the gear and bearing back into the gear case
and install the snap ring.
5. Follow steps 5 through 7 under Assembling the
Gear Reducer if this is all the service required.
6. Follow steps 4 through 7 under Assembling the
Gear Reducer if this is all the service required.
Replacing the Oil Seals
Assembling the Gear Reducer
1. Follow steps 1 through 3 under Replacing the
Gasket.
1. Grease the o–ring and make sure it’
placed on the gear cover
s properly
.
2. Loosen the setscrew, using a 4 mm wrench, and pull
2. Place the four oil seals and screws in the gear cover
.
the gear off the pump with a gear puller
.
Place the o–ring on the screw to hold it in the cover
.
3. Using a 6 mm wrench, remove the four screws. Be
sure to keep them separate from the other nine
3. Apply low strength Loctite r (blue) on the screw
threads, align the screws with the holes in the pump,
screws removed previously
.
and tighten the screws oppositely and evenly
.
4. Remove the four oil seals and replace them.
4. Grease the pump shaft. Align the gear
key on the pump shaft and slide the gear onto the
shaft, up to the pump’s shoulder Apply low strength
’s slot with the
5. Follow steps 2 through 7 under Assembling the
Gear Reducer if this is all the service required.
.
Loctiter on the setscrew threads and tighten the
setscrew to lock the gear on the shaft.
Replacing the O–Ring
1. Follow the instructions under Replacing the Gasket
and Replacing the Oil Seals to disassemble the
gear reducer.
5. Make sure the gasket is in place (refer to step 4
under Replacing the Gasket). Install the gear cover
on the case, aligning the holes, and secure it with
the nine screws and lockwashers. T
screws evenly in a crisscross pattern.
ighten the
2. Pull the gear cover of f the pump and replace the
o–ring.
6. Grease the engine shaft. Align the gear ’s slot with
the key on the engine shaft and slide the gear
3. Follow instructions under Assembling the Gear
Reducer if this is all the service required.
reducer onto the shaft, up to the engine’s shoulder
.
7. Secure the gear reducer to the engine with the four
bolts, lockwashers, and washers.
308-505 16
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DRAWING
802–143 Gear Reducer (2040)
1
2
3
4
10
21
20
5
11
6
12
7
13
14
8
9
17
19
12
18
15
16
PARTS LIST
802–143 Gear Reducer (2040)
REF PART
NO. NO.
DESCRIPTION
QTY
1
1
2
802–332 O–RING
802–333 COVER, Mounting
802–334 SCREW, Set
802–335 GEAR, Pump
802–336 GEAR, Engine
802–337 RING, Snap
802–338 BEARING
1
3
1
4
1
5
1
6
1
7
1
8
802–339 RING, Snap
802–340 GASKET
801–475 DIPSTICK
1
9
1
10
11
12
13
14
15
16
17
18
19
20
21
1
802–341 CASE, Mounting
801–023 WASHER, Lock
802–342 SCREW
1
13
9
802–343 SEAL, Oil
1
802–344 O–RING
1
801–484 CAP, G 3/8 BSP
802–345 GAUGE, Sight
801–025 WASHER, Flat
802–331 BOLT, 5/16–24 x 1”
802–346 SCREW
1
1
4
4
4
802–347 SEAL, Oil
4
17 308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DRAWING
802–265 Pump Assembly, 1500 psi
10
9
24
23
8
18
19
13
7
20
21
11
6
22
15
5
4
14
12
52
1
14
47
48
17
3
16
2
12
49
51
11
50
9
10
22
45
18
21
44
19
29
26
25
37
33
31
39
36
35
34
30
32
28
27
38
40
41
28
42
43
308-505 18
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
802–265 Pump Assembly, 1500 psi
REF PART
REF
NO. NO.
803–273 SCREW, Cap, socket hd.
PART
NO. NO.
DESCRIPTION
QTY
DESCRIPTION
QTY
1
2
3
802–319 MANIFOLD, 1500 psi
801–651 SCREW, Cap, socket hd.
801–652 WASHER, Lock
1
8
8
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
5
n
O–RING
802–345 GAUGE, Sight
802–793 PLUG, Oil Drain
803–328 CRANKSHAFT
803–275 PIN, Wrist
1
1
1
3
1
3
6
6
6
3
3
3
4
5
6
7
8
9
:
:
:
:
:
D
:
#z
z
z
z
z
\
O–RING
SEAT, Valve
PLATE, Valve
SPRING
GUIDE, Valve
O–RING
CAP
VALVE ASSEMBL
PACKING
RETAINER, Packing
RING, Head
802–794 KEY
803–276 ROD, Connecting
803–277 WASHER, Flat
803–278 WASHER, Lock
803–279 SCREW, Cap, socket hd.
803–330 GUIDE, Piston
801–489 WASHER, Flinger
801–661 PLUNGER, Ceramic
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
D
Y
RETAINER, Packing
O–RING
SEAL, Oil
n
n
n
RING, Backup
WASHER
SCREW, Piston
803–265 SCREW, Cap, hex hd
803–266 COVER, Crankcase
803–267 SPACER
8
2
1
2
2
1
1
1
1
803–281 SPACER
1
1
803–282 SEAL, Crankshaft
NOT USED
803–268 O–RING
802–317 WASHER, Lock
802–318 SCREW, Cap, socket hd.
801–484 PLUG, Hex
801–482 PLUG, Hex
801–483 WASHER, Flat
801–485 WASHER, Flat
2
2
1
1
1
1
803–269 BEARING, Ball
803–326 CRANKCASE
801–659 DIPSTICK
803–327 GASKET, Cover
802–526 COVER, Crankcase
:
D
n
#
Part of kit 1, 801–472 Valve Kit
Part of kit 4, 802–306 Valve Cap Kit
Part of kit 6, 801–474 Plunger Repair Kit
Part of kit 19, 801–662 Packing Kit
Part of kit 23, 801–658 Oil Seal Kit
\
z
Part of kit 27, 801–664 Packing and Retainer Kit
19 308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DRAWING
803–405 Pump Assembly, 2000 psi
10
9
20
19
18
8
12
7
13
11
6
14
5
45
46
54
4
1
47
50
49
44
45
17
3
16
2
42
43
44
53
11
9
52
10
51
40
15
41
14
39
12
29
28
21
23
32
33
26
22
24
30
25
31
34
27
35
36
31
37
38
308-505 20
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
803–405 Pump Assembly, 2000 psi
REF PART
NO. NO.
REF
PART
DESCRIPTION
QTY
NO. NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
801–467 MANIFOLD, 2000 psi
801–468 SCREW, Cap, hex hd.
801–469 WASHER, Lock
1
8
8
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
803–321 COVER, Crankcase, 2000 psi
802–345 GAUGE, Sight
802–793 PLUG, Oil Drain
1
1
1
:
:
:
:
:
D
O–RING
n
O–RING
SEAT, Valve
PLATE, Valve
SPRING
GUIDE, Valve
O–RING
803–294 SCREW, Cap, socket hd
801–652 WASHER, Lock
6
6
3
3
801–489 WASHER, Flinger
801–490 PLUNGER, Ceramic
n
n
n
RING, Backup
WASHER
SCREW, Piston
D
CAP
VALVE ASSEMBL
:
Y
803–283 SCREW, Cap, socket hd.
803–284 COVER, Crankcase
8
1
2
2
803–295 COVER, Crankcase
803–296 SHIM
1
2
802–500 O–RING, Crankcase Cover
803–285 BEARING, Tapered Roller
K
SEAL, Oil
O–RING
RETAINER, Packing
PACKING
RING, Head
RETAINER, Packing
RING, Long Life
J
J
J[
J
J
J
h
SEAL, Oil
803–286 BUSHING, Piston
802–895 CRANKCASE
801–475 DIPSTICK
1
1
1
1
1
6
1
3
3
3
5
803–144 GASKET, Cover
803–332 CRANKSHAFT, 2000 psi
803–288 RING, Retaining
802–794 KEY
NOT USED
802–305 SCREW, Cap, socket hd.
802–304 WASHER, Lock
801–482 PLUG, Hex
801–483 WASHER, Flat
801–484 PLUG, Hex
801–485 WASHER, Flat
2
2
1
1
1
1
803–289 PIN, Wrist
803–323 GUIDE, Piston, 2000 psi
803–291 ROD, Connecting
803–273 SCREW, Cap, socket hd
:
h
Part of kit 1, 801–472 Valve Kit
Part of kit 2, 801–473 Oil Seal Kit
Part of kit 3, 802–511 Crankshaft Seal Kit
Part of kit 4, 802–306 Valve Cap Kit
Part of kit 6, 801–474 Plunger Repair Kit
Part of kit 8, 801–486 Packing Kit
K
D
n
[
J
Part of kit 28, 801–487 Packing and Retainer Kit
21 308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP SERVICE
Servicing the Plungers
WARNING
To reduce the risk of serious bodily injury
including fluid injection, splashing in the eyes or
on the skin, or injury from moving parts, always
,
NOTE: Plunger repair kit, P/N 801–474 is available to
replace retainers, o–rings, washers and
backup rings for three cylinders.
follow the
Pressure Relief Procedure
Warning before proceeding.
1. Loosen the plunger retaining screw five to six turns,
using an M10 wrench. Push the plunger towards the
crankcase to separate the plunger and retaining
screw.
NOTE: The following metric wrenches are needed:
M10, M13 and M30. Repair kits are available.
Refer to the individual repair sections and the
pump parts page for more details. For the best
results, use all parts in the kits.
2. Remove the screw from the plunger and examine
the o–ring, backup ring and copper bearing/gasket
washer. Replace these parts if necessary using kit
801–474.
NOTE: There are two dif ferent tool kits to aid in
servicing the pump. P/N 800–298 is used to
ease installation of packings. P/N 800–271
includes the items in 800–298 and tools to aid
in the removal of packing retainers.
3. Remove the plunger and flinger from the plunger
shaft. Clean, examine and replace parts as
necessary.
4. Inspect the plunger shaft for oil leakage from the
crankcase. If leaking is obvious, replace the oil
seals. Otherwise, DO NOT remove these seals as
they cannot be reused. An oil seal kit is available to
replace the seals.
Valves
NOTE: For a set of six valves, order P/N 801–472.
1. Remove the hex plug from the manifold using an
M30 wrench.
5. Lightly grease the flinger and oil seal, if it is being
replaced and replace them on the plunger shaft.
2. Examine the o–ring under the hex plug and replace
it if it is cut or distorted.
Then install the plunger
.
6. Lightly grease the retaining screw and the outer end
of the plunger. Place the washer, o–ring and backup
ring around the screw and install the screw through
the plunger. Torque to 14.4 ft–lb (19.5 Nm).
3. Remove the valve assembly from the cavity; the
assembly may come apart.
4. Install the new valve. Install the o–ring and hex plug;
torque to 75 ft–lb (103 Nm).
NOTE: If you plan to replace the packings, refer to
Servicing the V–Packings.
NOTE: Retorque the plug after 5 hours of operation.
7. Lubricate the outside of each plunger . Slide the
manifold onto the crankcase, being careful not to
damage the seals.
Pumping Section
1. Remove the eight capscrews and lockwashers from
the manifold using an M13 wrench.
8. Install the capscrews and washers finger–tight.
Torque the screws to 21.7 ft–lb (29 Nm) following
the tightening pattern (Figure 4). Uneven tightening
may cause the manifold to bind or jam.
2. Carefully separate the manifold from the crankcase.
NOTE: It may be necessary to tap the manifold lightly
with a soft mallet to loosen.
CAUTION
5
8
1
3
4
2
7
6
Keep the manifold properly aligned with the
ceramic plungers when removing to avoid
damage to the plunger or seals.
3. Carefully examine each plunger for any scoring or
cracking and replace as necessary
.
Figure 4
308-505 22
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Thoroughly clean the packing cavities and examine.
Servicing the V–Packings
NOTE: There are two types of packing kits: one is just
packings, the other includes the packings,
rings and retainers.
6. Lightly grease the packing cavities and then replace
the packings in the following order: head ring,
v–packing, intermediate ring, head ring, v–packing
and packing retainer with the o–ring installed in the
retainer groove.
1. Remove the manifold as outlined in the Pumping
Section.
CAUTION
2. Carefully pull the packing retainer from the
manifold. Examine the o–ring and replace it if it is cut
or damaged.
Be very sure the parts are installed in the proper
order and facing the correct direction. See
Pump assembly on pages 18 and 20.
Improperly installed parts will cause a
malfunction.
3. Remove the v–packing and head ring. Pull out the
intermediate retainer ring. Remove the second
v–packing and second head ring.
7. Reassemble the manifold as instructed in Servicing
the Plungers.
4. Inspect all parts and replace as necessary
.
ACCESSORIES
(Must be purchased separately)
DOWNSTREAM CHEMICAL INJECTOR KIT
(1535) 800–139
DOWNSTREAM CHEMICAL INJECTOR KIT
(2040) 800–111
For injecting harsh cleaning chemicals downstream
from the pump.
BACKFLOW PREVENTOR 801–133
Prevent back–up of contaminated water into fresh
supply. Install upstream of pump.
ANTI–FREEZE FLUSH KIT 802–327
For flushing system with 50% anti–freeze solution prior
to transporting or storing pressure washer in below
freezing temperatures.
UPSTREAM CHEMICAL INJECTOR KIT
800–257
INLET PRESSURE REGULATOR 800–258
Regulates inlet water pressure to 60 psi (4 bar)
maximum.
For injecting mild cleaning chemicals upstream into the
pump.
TECHNICAL DATA
Model 800–165
Model 800–367
Model 800–164
Model 800–290
Engine
(air–cooled, 4 cycle)
5 hp Honda OHV
5 hp Briggs &
Stratton I/C
8 hp Briggs &
Stratton I/C
8 hp Honda OHV
Gasoline Tank Capacity
3.8 quarts (3.6 liter)
1500 psi (103 bar)
3 quarts (2.8 liter)
1500 psi (103 bar)
6 quarts (5.7 liter)
2000 psi (138 bar)
6.2 quarts (6 liter)
2000 psi (138 bar)
Water Pump Maximum
Working Pressure
W
ater Pump Maximum Flow 3.5 gpm (13 lpm)
3.5 gpm (13 lpm)
3/4” garden hose (f)
105 lb (48 kg)
4 gpm (15 lpm)
3/4” garden hose (f)
152 lb (68 kg)
4 gpm (15 lpm)
3/4” garden hose (f)
158 lb (70 kg)
Inlet Hose Connection
Weight
3/4” garden hose (f)
105 lb (48 kg)
Dimensions
Length
37” (940 mm)
19” (483 mm)
20” (508 mm)
37” (940 mm)
19” (483 mm)
20” (508 mm)
36” (914 mm)
21” (533 mm)
22.5” (572 mm)
36” (914 mm)
21” (533 mm)
22.5” (572 mm)
Width
Height
Maximum Inlet Water
Temperature
160_
F
(70_
C)
160_
F
(70_
C)
160_
F
(70_
C)
160_
F
(70_
C)
W
etted Parts
High Pressure Hose
Acrylonitrile and Buna–N cover and tube
Synthetic yarn and EPDM
Bypass Hose
Pressure Washer
(including fittings)
Anodized aluminum, Aluminum or bronze alloys, Brass Copper, Nylon–
r
composite,
PTFE
Ceramic, Buna–N, Cotton phenolic, 303, 304, and 316 Stainless steel, Polymide–12
thermoplastic,
r, Carbon steel, Zinc with or without yellow chromate plate
PTFE
is a registered trademark of the DuPont Company
.
PTFE
23 308-505
Download from Www.Somanuals.com. All Manuals Search And Download.
THE GRACO WARRANTY
WARRANTY AND DISCLAIMERS
Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and
workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As
purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twenty four months from date
of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the
equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence,
accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for
malfunction, damage or wear caused by the incompatibility with Graco equipment of structures,
accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by
Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for
examination by Graco to verify the claimed defect. If the claimed defect is verified, Graco will repair or
replace free of charge any defective parts. The equipment will be returned to the original purchaser
transportation prepaid. If inspection of the equipment does not disclose any defect in material or
workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts,
labor and transportation.
DISCLAIMERS AND LIMITATIONS
THE TERMS OF THIS W ARRANTY CONSTITUTE THE PURCHASER’S SOLE AND EXCLUSIVE
REMEDY AND ARE IN LIEU OF ANY OTHER WARRANTIES (EXPRESS OR IMPLIED), INCLUDING
WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,
AND OF ANY NON–CONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON
NEGLIGENCE OR STRICT LIABILITY . EVERY FORM OF LIABILITY FOR DIRECT , SPECIAL OR
CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSL Y EXCLUDED AND DENIED. IN NO CASE
SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR
BREACH OF WARRANTY MUST BE BROUGHT WITHIN THREE (3) YEARS OF THE DATE OF SALE.
EQUIPMENT NOT COVERED BY GRACO WARRANTY
GRACO MAKES NO W ARRANTY, AND DISCLAIMS ALL IMPLIED W
ARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A P ARTICULAR PURPOSE, WITH RESPECT T
O
ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED
BY GRACO. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.)
are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable
assistance in making any claim for breach of these warranties.
Factory Branches: Atlanta, Chicago, Dallas, Detroit, Los Angeles, West Caldwell (N.J.)
Subsidiary and Affiliate Companies: Canada; England; Switzerland; France; Germany; Hong Kong; Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN U.S.A. 308–505 10/89
308-505 24
Download from Www.Somanuals.com. All Manuals Search And Download.
|