INSTRUCTIONS–PARTS LIST
309445
Rev. E
Important Safety Instructions
To find your local Graco authorized service
center:
D
Read all warnings and instructions
in this manual. Save these
instructions.
D
C
a
l
l
u
s
a
t
1
–
8
0
0
–
6
9
0
–
2
8
9
4
D
V
i
s
i
t
o
u
r
w
e
b
s
i
t
e
a
t
w
w
w
.
g
r
a
c
o
.
c
o
m
Pressure Roller with 20”
Heavy Duty Extension, EvenFlowt Roller
Frame and Contractort Inline Valve
– For the rolled application of architectural paints and
coatings –
Model 245397, Series C
D 20 in. (50 cm) Heavy-Duty Extension
D 9 in. (23 cm) EvenFlowt Roller Frame
D 1/2 in. (13 mm) Nap Roller Cover
D Contractort Inline Valve
3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure
*
The best operating pressure is the lowest pressure that provides
*
an even paint supply to the roller and typically does not exceed
300 psi (2.1 MPa, 21 bar).
CAUTION
Never leave water in the pump, inline valve, or roller frame.
Doing so could cause corrosion and damage from freezing.
For storage, flush the system with Graco Pump Armort or
mineral spirits/paint thinner.
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441
ECOPYRIGHT 2001, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Assemble pressure roller as shown in Parts Drawing,
page 7. Attach pressure roller assembly to inline
D When connecting EvenFlow roller frame to the
Contractort Inline Valve, use a wrench to tighten.
valve.
Pressure Relief Procedure
3. Turn prime/spray valve to PRIME position to
relieve pressure in system.
WARNING
To help prevent injection injuries,
follow this procedure whenever
you stop painting.
4. Put inline valve trigger safety in SAFETY OFF
position, and trigger inline valve to relieve any
pressure in hose.
psi/MPa/bar
1. Put inline valve trigger safety in SAFETY ON
position (Fig. 1).
5. Put inline valve trigger safety in SAFETY ON
position, and keep pump prime/spray valve in
PRIME position until you paint again.
2. Shut off power to pump.
309445
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
D
T
h
e
C
o
n
t
r
a
c
t
o
r
t
I
n
l
i
n
e
V
a
l
v
e
c
a
n
b
e
u
s
e
d
a
s
a
n
WARNING
SKIN INJECTION HAZARD
airless spray gun by attaching a Handtitet Guard
and RAC5 Switchtip.
To reduce the risk of a fluid injection
injury, do not operate the inline valve with
the tip guard or trigger guard removed.
1. Follow pump priming instructions using lowest
pressure setting at which pump primes.
2. Turn prime/spray valve to SPRAY position.
In-Line Valve Trigger Safety Lever
3. Disengage inline valve safety latch, trigger the
inline valve, and roll the surface until paint comes
to roller.
For SAFETY ON position, rotate trigger safety lever so
it is in line with trigger. For SAFETY OFF position, flip
safety lever so it is 90_ to trigger. Fig. 1.
NOTE: Trigger the inline valve briefly only when
you need more paint. Determine how often you
must trigger the inline valve to maintain an even
paint supply to the roller.
NOTE: In the SAFETY ON position the lever sits in a
detent which holds it in place.
4. Increase pump pressure only if triggering inline
valve cannot supply enough paint for your rolling
speed.
Relieve pressure, page 3,
whenever you stop painting.
Elevate roller end of
5.
SAFETY ON
SAFETY OFF
Fig. 1
extension tube to prevent
paint from draining out.
Startup
Flush pump, inline valve, and roller frame immediately
after each use to prevent paint from drying in roller
frame and damaging it.
NOTE:
Cleaning
NOTE: Follow this procedure to flush the roller frame
and inline valve. The pump you are using may have
additional flushing steps, such as cleaning filters and
screens. See the pump flushing instructions.
Cleaning the EvenFlow Roller Frame
1.
Relieve pressure, page 3.
2. Remove roller cover (19) and diffuser (23) from
Leave the roller frame attached to the inline valve for
this procedure.
roller frame as follows (see Parts Drawing):
a. Using your thumb, press down on clip (5) to
release end caps (2 &4), diffuser (23) and
roller cover (19) into a pail.
b. Remove roller cover (19) from diffuser (23).
c. Pull end caps (2 & 4) off diffuser (23).
3. Clean roller cover (19), caps (2 & 4) and diffuser
(19) with water or a compatible fluid for oil–based
materials.
4. Place roller frame (1) in paint pail. Be sure the
holes in roller frame (1) are facing inside the paint
pail.
4
309445
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Prime pump with water or flushing fluid for oil–
based materials. Use the lowest pump priming
pressure setting.
Cleaning Contractor Inline Valve
Relieve pressure, page 3.
1.
6. Turn prime/spray valve to SPRAY.
2. Push up on bottom of trigger guard and swing it
away from trigger.
NOTE: Perform Step 7 at the lowest pressure pos-
sible.
3. Unscrew inline valve handle from housing. Re-
move filter and clean it in compatible solvent.
7. Trigger inline valve until flushing fluid begins to
dilute the paint.
NOTE: Do not soak entire inline valve in solvent.
Prolonged exposure to solvent can ruin packings.
8. Place roller frame (1) in another bucket and contin-
ue flushing until fluid coming out of the roller frame
(1) is clear.
4. Apply lithium–based grease to threads of inline
valve handle and reassemble inline valve.
Storage
If you are going to store the airless equipment for an
extended period of time after flushing with water-base
fluid, flush again with Graco Pump Armor or mineral
spirits/paint thinner. Leave this fluid in the system
during storage.
309445
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
6
309445
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
23
Model 245397, Series A
Ref.
No.
4
Part No. Description
Qty.
1
1
2
4
244271*
245999
246277
FRAME, roller
CAP, end (includes seal and retainer)
CAP, end (includes seal, retainer, and
1
1
o–ring)
CLIP, roller
GASKET
1
1
1
5
7
197106
15H622
5
12
14
19
115524
232122
107590
GASKET
1
1
2
EXTENSION, 20 in. (50 cm)
12
ROLLER, cover, 9 inch,
1/2 in. (13 mm) nap
ti10642a
19
1
2
23
15B065
DIFFUSER
*244271 Frame includes 1, 2, 4, 5, 12, 19, 23.
14
7
Pressure Roller
Additional Roller Covers
Additional Heavy Duty Extensions
The following extensions can be mixed and matched to
create any length pressure roller needed and are
available at your local distributor:
The following pressure roller covers are available at
your local distributor:
232121
232122
232123
232124
232125
10 in. (25 cm)
20 in. (50 cm)
40 in. (100 cm)
60 in. (150 cm)
80 in. (200 cm)
107589
107590
107591
107592
9 in. (23 cm); 3/8 in. (9.5 mm) nap
9 in. (23 cm); 1/2 in. (13 mm) nap
9 in. (23 cm); 3/4 in. (19 mm) nap
9 in. (23 cm); 1-1/4 in. (32 mm) nap
309445
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
101
108
119
111
110
105a
120
106
105b
107
102
105
105c
113
105d
103
114
112
TI0667
104
8
309445
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Contractort In–line Valve
Model 244161
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
107
108
110
111
112
113
114
119
120
107110
197052
197058
197568
113409
195788
104938
177538
105334
LOCKNUT
1
1
1
1
1
1
1
2
2
101
102
218070
244193
NEEDLE–DIFFUSER/SEAT KIT
TRIGGER, valve, In–line
(includes 107)
GUARD, trigger
KIT, swivel
1
ADAPTER, RAC
BRACKET, stem
HOUSING, fluid
RETAINER, guard
HANDLE, valve
PACKING, o–ring
STUD, trigger
LOCKNUT
1
1
1
1
103
104
105n 218131
196869
238817
FLUID FILTER ASSEMBLY
(standard 50 mesh) includes
replacement parts 5a, 5b, 5c, 5d
RETAINER, spring
ELEMENT, strainer
SPRING, compression
RETAINER, spring
105a 179722
105b 179731
105c 179763
105d 179750
106n 179733
1
1
1
1
1
n
Keep these items on hand to reduce down time.
D The Contractort Inline Valve contains a paint filter
(218131) inside handle. The primary function of the
paint filter is to prevent clogging of spray tips.
SEAL, sleeve
D
T
h
e
p
a
i
n
t
f
i
l
t
e
r
m
a
y
b
e
r
e
m
o
v
e
d
f
o
r
r
o
l
l
i
n
g
a
p
p
l
i
c
a
-
tions.
D
R
e
m
o
v
e
a
n
d
c
l
e
a
n
f
i
l
t
e
r
s
a
f
t
e
r
e
a
c
h
u
s
e
.
309445
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–690–2894 Toll Free
All written and visual data contained in this document reflect the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 309445
Graco Headquarters: Minneapolis
International Offices: Belgium, Korea, China, Japan
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441
9/2001, Revised 9/2007
10
309445
Download from Www.Somanuals.com. All Manuals Search And Download.
|