INSTRUCTIONS-PARTS LIST
308–236
Rev. J
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
Supersedes Rev. H
First choice when
quality counts.t
INSTRUCTIONS
Silver Airless Spray Gun
5000 psi (345 bar) Maximum Working Pressure
Model 237–695, Series B
2
finger trigger. Tip Guard and
Spray tip not included; order separately
.
Model 235–460, Series C
Includes the Standard (non-reversing) DripLesst
Tip Guard and 2 finger trigger.
Spray tip not included; order separately
.
Model 235–461, Series B
Includes the Standard (non-reversing) DripLesst
Tip Guard and 4 finger trigger.
Spray tip not included; order separately
.
Model 235–462, Series C
01471
Model 235–460
For Fine-Finish. Includes the standard
(non-reversing) DripLesst Tip Guard
and 2 finger trigger
.
Spray tip not included; order separately
.
Model 235–463, Series D
Includes RACr DripLesst Guard, 517 size
SwitchTipt, and 2 finger trigger
.
Model 235–464, Series C
Includes Heavy Duty RACr Tip Assembly
,
.
617 size SwitchTipt, and 2 finger trigger
Model 238–591, Series A
Includes Heavy Duty RACr Tip Assembly
,
525 size SwitchTipt, and 4 finger trigger
.
Model 236–531, Series C
Includes Heavy Duty RACr Tip Assembly
,
.
415 size SwitchTipt, and 2 finger trigger
Model 238–966, Series A
Includes Heavy Duty RACr Tip Assembly
,
Model 235–463
Customer specified tip, four finger fluid housing
and 2 finger trigger
.
01472A
Patents Pending
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
eCOPYRIGHT 1992, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
INJECTION HAZARD
Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also
cause serious injury
.
D
Fluid injected into the skin might look like just a cut, but it is a serious injury
cal attention.
.
Get immediate medi-
D
D
D
D
D
D
D
D
D
Do not point the gun at anyone or at any part of the body
.
Do not put your hand or fingers over the spray tip.
Do not stop or deflect leaks with your hand, body, glove or rag.
Do not “blow back” fluid; this is not an air spray system.
Always have the tip guard and the trigger guard on the gun when spraying.
Check the gun diffuser operation weekly. See page 8.
Be sure the gun trigger safety operates before spraying.
Lock the gun trigger safety when you stop spraying.
Follow the Pressure Relief Procedure on page 5 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
D Tighten all fluid connections before operating the equipment.
D
Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
Do not repair high pressure couplings; you must replace the entire hose.
D
Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
D
D
Keep clear of all moving parts when starting or operating the pump.
Before servicing the equipment, follow the Pressure Relief Procedure on page 5 to prevent the
equipment from starting unexpectedly
.
RECOIL HAZARD
Due to the high pressure fluid emitted, a strong recoil action may occur when you trigger this gun. If
you are unprepared, your hand could be forced back toward your body or you could lose your balance
and fall, resulting in serious injury
.
308-236
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury
.
D
D
If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately Do not use the equipment until you identify and correct the problem.
.
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D
D
D
D
D
D
D
Keep the spray area free of debris, including solvent, rags, and gasoline.
Electrically disconnect all equipment in the spray area.
Extinguish all open flames or pilot lights in the spray area.
Do not smoke in the spray area.
Do not turn on or off any light switch in the spray area while operating or if fumes are present.
Do not operate a gasoline engine in the spray area.
Ground the equipment and the object being sprayed. Refer to your pump instruction manual.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D
D
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer
.
4
308-236
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation/Operation
Pressure Relief Procedure
WARNING
WARNING
INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
Be sure your system has a bleed-type master air
valve (pneumatic pumps only) and a pressure drain
valve. These accessories help reduce the risk of
serious bodily injury, including fluid injection,
splashing in the eyes or on the skin, or injury from
moving parts, if you are adjusting or repairing the
pump or gun.
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
1. The bleed-type master air valve (air-powered
pumps only) relieves air trapped between this
valve and the pump after the air regulator is shut
off. Trapped air can cause the pump to cycle
unexpectedly.
D
D
D
D
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray tips.
2. The pressure drain valve assists in relieving fluid
pressure in the displacement pump, hose and gun:
triggering the gun to relieve pressure may not be
sufficient.
1. Lock the gun trigger safety
.
2. Shut off the power supply to the pump. Close any
bleed-type master air valves.
3. Strain the fluid you are spraying if it contains
particles which could clog the spray tip.
3. Unlock the gun trigger safety
.
4. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
How to Use the Gun Trigger Safety
1. To lock the gun trigger safety, turn the latch to a
right angle with the gun body. See Fig. 1.
5. Lock the gun trigger safety
.
6. Open the drain valve (required in your system),
having a container ready to catch the drainage.
2. To unlock the gun trigger safety, push the latch out
and turn it parallel with the gun body
.
7. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the tip or hose.
The trigger safety is shown
in the locked position.
1
2
The trigger safety is shown
in the unlocked position.
1
System Requirements
WARNING
Keep the wallet-sized warning card provided with
this gun with the operator at all times. The card
contains important treatment information should an
injection injury occur. Additional cards are available
at no charge from Graco Inc.
2
01474A
Fig. 1
308-236
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation/Operation
7. If adjusting the pressure does not give a good
How to Use the Gun
spray pattern, follow the Pressure Relief Proce
-
dure on page 5 and then try another tip size.
1. Connect a grounded fluid hose to the gun inlet.
See Fig. 2.
8. Use a full-open, full-close triggering action. Hold
the gun about 14 in. (350 mm) from and at right
2. With no tip installed, start the pump. Flush the
pump according to the instructions supplied with it.
Prime the system with the fluid.
angles to the work surface. Don’t swing the gun in
an arc. Practice to find the best length and speed
of stroke.
How to Adjust the Spray Pattern
WARNING
T
o reduce the risk of serious injury whenever you
WARNING
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
3. Relieve the pressure. Be sure the gun trigger
safety is locked. See Fig. 1.
1. Relieve the pressure. Loosen the retaining nut
(B). Turn the tip guard so the groove in the tip is
horizontal (C) for a horizontal pattern and vertical
(A) for a vertical pattern. Tighten the retaining nut.
See Fig. 3.
4. Models 235–460, 235–461, and 235–462: screw
the tip guard (1) and install the tip (A) and the
gasket (2d) in the nut of the tip guard. Screw the
assembly firmly onto the gun. Tighten the assem
bly with a wrench. See Fig. 2.
-
2. The orifice of the spray tip and the angle of the
spray pattern determines the coverage and the
size of the pattern. When more coverage is
needed, use a larger spray tip rather than
increasing the fluid pressure.
NOTE: If the gasket (2d) is not installed, the gun
will leak.
5. Models 235–463, 235–464, 238–591, 236–531 and
238–966: install the SwitchTip (16) and the tip
guard (17). See manual 308–644 or 307–991,
supplied.
CAUTION
The openings in the tip guard reduce paint buildup on
the tip guard while spraying. Any damage to the
sharp edges of the openings causes paint to collect
at that area. Never hang the gun by the tip guard.
2d
A
1
KEY
A
Tip guard shown in position for
vertical spray pattern
Retaining nut
B
C
T
ip guard shown in position for
horizontal spray pattern
B
A
C
16
17
01473
Fig. 2
6. Start the pump. Adjust the fluid pressure until the
spray is completely atomized. Use the lowest
pressure necessary to get the desired results.
Higher pressure may not improve the spray pattern
01472A
7658A
Fig. 3
and will cause premature tip wear and pump wear
.
6
308-236
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation/Operation
Clearing an Obstruction
How to Clean the Spray Tip
If the spray tip clogs while spraying, immediately stop
spraying, then:
and Clear a Spray Tip Obstruction
Gun 235–460, 235–461, 235–462
– with standard tip guard
WARNING
To reduce the risk of fluid injection or splashing in
the eyes or on the skin, do not hold a hand, body
or rag in front of the spray tip when cleaning or
checking a clogged tip. Point the gun toward the
ground or into a waste container when checking to
see if the spray tip is cleared.
1. Lock the gun trigger safety, open the pressure
drain valve.
2. Remove the spray tip and blow out the obstruction
by applying air to the front of the spray tip. Or, let
the spray tip and gun nozzle soak to dissolve the
obstruction. If it won’t dissolve, jar it out by tapping
the back of the spray tip against a flat surface.
Do not try to “blow back” paint; this is not an air
spray gun.
CAUTION
Never soak the entire gun in solvent. Prolonged
Do not wipe fluid buildup off the gun or spray tip
until pressure is relieved.
exposure to solvent can ruin the packings.
Gun 235–463, 235–464, 238–591, 236–531 and
238–966 – with RAC guard or Heavy Duty RAC guard
Cleaning During the Day
1. Lock the gun trigger safety. Rotate the RAC guard
WARNING
o reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
handle 180_. See Fig. 4.
T
2. Unlock the gun trigger safety. Trigger the gun into
a pail or onto the ground to remove the clog.
3. Lock the gun trigger safety. Rotate the tip handle
to the spraying position.
1. Relieve the pressure.
4. If the tip is still clogged, lock the gun trigger safety
,
2. Clean the front of the tip frequently during the day
to help reduce buildup. Also clean the tip and tip
guard at the end of each work day. Use a solvent-
soaked brush to clean the spray tip.
shut off the sprayer and disconnect the power
source, and open the pressure drain valve to
relieve pressure. Clean the spray tip as shown in
manual 308–644, supplied with the RAC; or in
manual 307–991, supplied with HD RAC.
KEY
A
Handle shown in spraying
position. Turn handle
180_ and
trigger gun to clear clog.
A
01472A
Fig. 4
308-236
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation/Operation
How to Check the Gun Diffuser Operation
2a
WARNING
The Fine–Finish Gun, Model 235–462, uses a
pre–orifice in the seat to develop the type of spray
pattern required for fine finishes. The pre-orifice
does not diffuse the spray from the nozzle into an
irregular pattern, as with the other guns covered in
this manual. Therefore, to reduce the risk of an
injection injury when the tip guard is not installed,
such as during cleaning, take extra precautions to
keep your hands and body away from the nozzle of
the gun.
Fig. 5
How to Flush the Gun
Always flush the pump and the gun before the fluid
being sprayed can dry in it.
NOTE: If it is available, the flushing procedure
provided in your pump or sprayer manual should be
used instead of this procedure.
For all other guns, check the diffuser operation weekly
.
The gun diffuser/seat (2a) breaks up spray and re
duces the risk of fluid injection when the tip is not
-
installed. Perform the test below. If it fails, replace the
entire Needle Kit, Part No. 235–474, as instructed on
page 9. Diffuser/seats are not sold separately since
the gun will leak if an old needle is used with a new
diffuser/seat.
WARNING
FIRE AND EXPLOSION HAZARD
Static sparking and splashing may cause
fire, explosion and serious injury. To
reduce static sparking and splashing,
always remove the spray tip from the gun, and hold
a metal part of the gun firmly to the side of a
grounded metal pail when flushing.
WARNING
T
o reduce the risk of serious injury whenever you
WARNING
o reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
T
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
1. Relieve the pressure.
1. Relieve the pressure.
2. Remove the tip guard and spray tip. Soak and
clean the parts.
2. Remove the tip guard and spray tip.
3. Put the pump intake in a grounded pail of water or
solvent.
3. Start the sprayer and adjust it to the lowest
pressure.
4. Start the pump at its lowest pressure.
5. Trigger the gun into the original pail. When solvent
appears, release the trigger
.
4. Aim the gun into a grounded metal pail while
holding it firmly to the pail. Trigger the gun. If the
fluid emitted is not diffused into an irregular
6. Now trigger the gun into the solvent pail. Circulate
the fluid until the system is thoroughly flushed.
stream, replace the entire needle kit immediately
.
See Fig. 5.
7. Relieve the pressure.
8
308-236
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
10
CAUTION
Do not attempt to install an old style needle in this
gun. The front of the new needle is marked with a +
below the Graco symbol.
2b*
2a*
8
Notes:
12
D
Use Needle Kit 235–475 for Model 235–462 and
Repair Kit 235–474 for the other models.
D
Use all the new parts for the best results. Parts
included in the kit are shown with one asterisk,
(2a*).
D
Keep parts very clean. Dried paint or other contami
nants cause friction which causes parts to wear
faster.
-
02352
Fig. 6
Needle Replacement
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
2c
1. Relieve the pressure.
2. Remove the hose, tip guard, spray tip and gasket.
3. Remove the diffuser/seat (2a*) and gasket (2b*).
Remove the screw (12), pivot pin (10), and trigger
(8). See Fig. 6.
02353
Fig. 7
4. Insert a punch into the rear of the gun and tap it to
push the needle (2c*) out the front of the gun. See
Fig. 7.
A
5. Clean the internal passages of the gun.
6. Grease the rings (A) of the new needle (2c*). See
Fig. 8.
Fig. 8
308-236
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
7. Slide the rear of the needle (2c*) into the front of
the gun. Slide the tool (B), provided with the repair
kit, into the gun, around the needle. Lightly tap the
tool with a hammer or lightly press the tool against
a flat surface to seat the needle. See Fig. 9.
Remove the tool.
B
CAUTION
2c
Tapping or pressing the tool too hard may jam the
tool and damage the needle.
8. Grease the end of the needle.
9. Grease the diffuser/seat threads. Place the new
gasket (2b*) on the diffuser/seat (2a*) and screw
the assembly into the fluid housing (6). Torque to
20–25 ft-lb (27–34 N.m). See Fig. 10.
02354
Fig. 9
Lubricate, then torque
to 20–25 ft–lb (27–34 N.m)
10. Install the trigger (8), pivot pin (10) and screw (12).
See Fig. 10.
1
10
NOTE: No needle or trigger adjustment is needed.
6
2b*
1
2a*
8
12
02352
Fig. 10
10
308-236
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
10
11
12
3
9
8
6
2
2
2c*
2b*
1
2a*
4
2d*
1
13
Lubricate, then
torque to 20-25 ft-lb
(27-34 N.m)
1
2
Lubricate
T
orque to 30-40 in-lb
(3.4–4.5 N.m)
3
4
Purchase separately
17
01477A
16
Model 235–460, Series C; Model 237–695, Series B
Model 235–460 Includes the Standard (non-reversing)
DripLesst Tip Guard and 2 finger trigger.
Includes items 1 to 15.
Model 235–461, Series B
Includes the Standard (non-reversing) DripLesst
Tip Guard and 4 finger trigger.
Includes items 1 to 15.
Model 237–695 is 2 finger trigger, without Tip Guard
and spray tip.
Includes items 2 to 15.
Ref
No.
Part No. Description
Qty.
1
2
220–251
235–474
STANDARD TIP GUARD
NEEDLE KIT
1
Ref
No.
Part No. Description
Qty.
Includes items 2a to 2d
DIFFUSER/SEAT
GASKET, copper
NEEDLE
TIP GASKET
FLUID HOUSING, four finger
TRIGGER, four finger
SETSCREW, 1/4–20
PIVOT PIN
GUN HANDLE
SCREW, hex washer hd, 10–24
SCREW, 1/4–20
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
220–251
235–474
STANDARD TIP GUARD
NEEDLE KIT
1
2a*
2b*
2c*
2d*
6
8
9
10
11
Z
Z
Includes items 2a to 2d
DIFFUSER/SEAT
GASKET, copper
NEEDLE
TIP GASKET
FLUID HOUSING, two finger
TRIGGER, two finger
SETSCREW, 1/4–20
PIVOT PIN
GUN HANDLE
SCREW, hex washer hd, 10–24
SCREW, 1/4–20
1
1
1
1
1
1
1
1
1
1
1
2
1
1
Z
2a*
2b*
2c*
2d*
6
8
9
10
11
Z
166–969
235–476
188–127
102–207
187–965
235–471
203–953
107–091
187–987
222–385
Z
Z
166–969
235–482
187–985
102–207
187–965
235–471
203–953
107–091
187–987
222–385
12
13
14Y
WARNING TAG not shown
WARNING CARD not shown
12
13
15Y
14Y
WARNING TAG not shown
WARNING CARD not shown
15Y
308-236 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 235–462, Series C
Model 235–464, Series C; Model 236–531, Series C
Includes the Fine-Finish (non-reversing) DripLesst
and Model 238–966, Series A
Models 235–464 and 236–531 includes Heavy Duty
T
ip Guard and 2 finger trigger
.
Includes items 1 to 15.
RACr tip, 2 finger fluid housing and 2 finger trigger
.
-
Model 238–966 includes Heavy Duty RACr tip, cus
Ref
tomer specified tip, 4 finger fluid housing and 2 finger
trigger .
Includes items 2 to 17.
No.
Part No. Description
Qty.
1
2
220–247
235–475
FINE FINISH TIP GUARD
NEEDLE KIT
1
Includes items 2a to 2d
PRE–ORIFICE SEAT
GASKET, copper
NEEDLE
TIP GASKET
FLUID HOUSING, two finger
TRIGGER, two finger
SETSCREW, 1/4–20
PIVOT PIN
GUN HANDLE
SCREW, hex washer hd, 10–24
SCREW, 1/4–20
1
1
1
1
1
1
1
1
1
1
1
2
1
1
Ref
No.
2a{
2b{
2c{
2d{
6
8
9
10
11
Z
Part No. Description
Qty.
Z
Z
162–863
235–482
187–985
102–207
187–965
235–471
203–953
107–091
187–987
222–385
2
235–474
NEEDLE KIT
Includes items 2a to 2c
DIFFUSER/SEAT
GASKET, copper
NEEDLE
1
1
1
1
1
1
1
2a*
2b*
2c*
2d*
6
Z
Z
Z
166–969
TIP GASKET
12
13
FLUID HOUSING
235–482
Two finger, Models 235–464
14Y
WARNING TAG not shown
WARNING CARD not shown
and 236–531
15Y
235–476
187–985
102–207
187–965
235–471
203–953
107–091
187–987
222–385
222–674
Four finger, Model 238–966
TRIGGER, two finger
SETSCREW, 1/4–20
PIVOT PIN
GUN HANDLE
SCREW, hex washer hd, 10–24
SCREW, 1/4–20
WARNING TAG not shown
WARNING CARD not shown
HEAVY DUTY RAC tip assembly
HEAVY DUTY SwitchTip
1
1
1
1
1
1
2
1
1
1
1
1
1
1
8
9
10
11
12
13
14Y
15Y
16
17
Model 235–463, Series D
Includes RACr guard and 2 finger trigger
.
Includes items 2 to 18.
Ref
No.
Part No. Description
Qty.
2
235–474
NEEDLE KIT
Includes items 2a to 2c
DIFFUSER/SEAT
GASKET, copper
NEEDLE
FLUID HOUSING, two finger
TRIGGER, two finger
SETSCREW, 1/4–20
PIVOT PIN
GUN HANDLE
SCREW, hex washer hd, 10–24
SCREW, 1/4–20
WARNING TAG not shown
WARNING CARD not shown
RAC DripLess GUARD
SwitchTip, Size 517
WARNING SHEET not shown
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2a*
2b*
2c*
6
8
9
10
11
12
13
14Y
15Y
16
17
18Y
Z
GHD–617 Size 617, Model 235–464
GHD–415 Size 415, Model 236–531
GHD–XXX Customer choice, Model 238–966
Z
Z
235–482
187–985
102–207
187–965
235–471
203–953
107–091
187–987
222–385
237–859
221–517
187–346
Model 238–591, Series A
Includes Heavy Duty RACr, tip and 4 finger trigger
.
Includes items 2 to 17.
Ref
No.
Part No. Description
Qty.
2
235–474
NEEDLE KIT
Includes items 2a to 2c
DIFFUSER/SEAT
GASKET, copper
NEEDLE
TIP GASKET
FLUID HOUSING, four finger
TRIGGER, four finger
SETSCREW, 1/4–20
PIVOT PIN
GUN HANDLE
SCREW, hex washer hd, 10–24
SCREW, 1/4–20
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2a*
2b*
2c*
2d*
6
8
9
10
11
12
13
14Y
15Y
16
Z
Z
The following information applies to all parts lists:
Z
166–969
235–483
188–127
102–207
187–965
235–471
203–953
107–091
187–987
222–385
237–162
*
These parts are also included in Repair Kit
235–474, which may be purchased separately. Kit
also includes installation tool.
{
These parts are also included in Repair Kit
235–475, which may be purchased separately. Kit
also includes installation tool.
WARNING TAG not shown
WARNING CARD not shown
HEAVY DUTY RAC tip assembly
Z
Y
Part not sold separately
Replacement Danger and Warning labels, tags and
cards are available at no cost.
17
GHD–525 HEAVY DUTY SwitchTip, Size 525
12
308-236
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
FILTERS
TOOLS
3000 psi (210 bar) Maximum Working Pressure.
NYLON BRUSHES
Use to thoroughly clean the gun’s fluid passages.
Adequate filtering is important for a good surface finish
and to minimize tip clogging. These filters provide
101–891 0.375” (9 mm) dia.
101–892 0.625” (16 mm) dia.
secondary filtering. Various screen meshes are avail
able.
-
Mounts in hose
WRENCH 171–147
Fits all hexes on the gun.
213–068 Includes filter body, spring and one
100 mesh screen.
213–069 Includes filter spring and one
60 mesh screen.
Use with above filter body
.
TIP GUARDS
210–742 Includes filter spring and one
100 mesh screen.
These tip guards fit all Graco airless spray guns.
Choose the one that’s right for your application. One of
these tip guards is included with every Graco airless
gun.
Use with above filter body
.
210–729 Includes assembly 213–068 plus a
3 ft (0.9 m) whip hose for more
flexible gun movement.
237–859 Performance Series Reverse–A–Clean
DripLesst Guard.
Mounts between hose and gun
Order SwitchTip separately
.
See your distributor for available sizes.
210–500 Includes swivel, adapter and one
100 mesh screen
Replacement screens for above filters
210–731 Three 60 mesh (250 micron) screens
210–732 Three 100 mesh (149 micron) screens
210–733 Three 200 mesh (74 micron) screens
SWIVELS and WHIP HOSES
220–251 Standard DripLesst Tip Guard.
Order flat tip separately.
Swivels and whip hoses provide more flexible gun
movement for easier handling and less fatigue.
See your distributor for available sizes.
Working pressures are listed in the descriptions.
207–946 Swivel, 1/2 npsm x 3/8 npt(f)
5000 psi (350 bar) Max. Working Pressure
204–940 Swivel, 1/4 npt x 1/4 npsm
3000 psi (210 bar) Max. Working Pressure
214–701 Whip hose, nylon, coupled 1/4 npsm(f)
x 3/8 npt(m), spring guards both ends.
222–674 Heavy Duty RACt DripLesst Tip Guard.
Order SwitchTip separately
.
3000 psi (210 bar) Max. Working Pressure
See your distributor for available sizes.
308-236 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Category
Data
Maximum fluid working pressure
Fluid orifice size
5000 psi (345 bar)
Model 235–462: 0.037 in. (0.94 mm)
All other models: 0.090 in. (2.3 mm)
W
etted parts
Stainless steel, Polyethylene, Polyurethane, Nylon, PTFE
r
Weight
18 oz (510 g)
1/4 npsm(m)
120_F (50_C)
78 dBa
Inlet
Maximum material temperature
* Sound pressure level
* Sound power level
87 dBa
* Measured while spraying waterbase paint – gravity 1.36 through a 517 tip at 3000 psi (207 bar) per ISO 3744.
TPTFEr is a registered trademark of the DuPont Co.
Manual Change Summary
Updated manual per ECO F5413.
14
308-236
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
308-236 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco
Warranty
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of
any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or
replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A
PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
LIMITATION OF LIABILITY
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
ADDITIONAL
WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty
Program.”
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–367–4023
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit, Los Angeles
Foreign Offices: Belgium, Canada, England, Korea, France, Germany, Hong Kong, Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN U.S.A. 308–236 December 1992, Revised August 1997
16
308-236
Download from Www.Somanuals.com. All Manuals Search And Download.
|
