ARGOS 70
Child Restraint/Booster Seat
Owner’s Manual
READ THIS MANUAL
Do not install or use this child restraint until
you read and understand the instructions in this
manual. FAILURE TO PROPERLY USE THIS CHILD
RESTRAINT INCREASES THE RISK OF SERIOUS
INJURY OR DEATH IN A SUDDEN STOP OR CRASH.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2011 Graco 6/11 US
PD169096A
Table of Contents
Table of Contents (cont.)
1.0 Warnings to Parents and Other
Users . . . . . . . . . . . . . . . . . . . . . 4-5
8.0 Choosing an Appropriate Vehicle
Seat Location . . . . . . . . . . . . . . .19
8.1 Vehicle Seat Location
11.0 Securing the Child Restraint
in Your Vehicle . . . . . . . . . . . . . . .32
11.1 Using a Child Restraint WITH a
Built-in Harness . . . . . . . . . .32
11.2 With a Vehicle Lap or
20.0 Securing Child in Vehicle Belt
with Shoulder Belt
Positioning Clip . . . . . . . . . . . 54-57
21.0 Using the Tether. . . . . . . . . . . . . .58
21.1 Storing LATCH and Tether. .59
22.0 Airplane Use . . . . . . . . . . . . . . . .60
23.0 Accessories . . . . . . . . . . . . . . . . .61
23.1 Body Support and Harness
Covers . . . . . . . . . . . . . . . . .61
24.0 Recline Foot . . . . . . . . . . . . . . . .62
25.0 Care and Maintenance . . . . . . . .63
2.0 Registration Information . . . . . . . . .6
2.1 Register Your Child Restraint .6
2.2 For Recall Information. . . . . . .6
2.3 If You Need Help . . . . . . . . . . .7
3.0 Useful Information . . . . . . . . . . . . .7
3.1 Certification . . . . . . . . . . . . . . .7
3.2 Child Restraint Useful Life. . . .7
3.3 Second Hand Child Restraint .7
4.0 Features . . . . . . . . . . . . . . . . . . . 8-9
5.0 Assembling the Child
Restraint . . . . . . . . . . . . . . . . . 10-13
6.0 WARNINGS . . . . . . . . . . . . . . 14-15
7.0 Height and Weight Limitations . . .16
7.1 WITH Built-in Harness. . . . . .16
7.2 WITHOUT Built-in Harness . .17
7.3 WITHOUT Back Support. . . .18
Requirements . . . . . . . . . . . .19
8.2 Vehicle Seat Belt
Requirements . . . . . . . . . . . .20
8.3 SAFE Vehicle Seat Belt
Systems . . . . . . . . . . . . . . . .20
8.4 For Built-in Harness Only . .21
8.5 WITH or WITHOUT Built-in
Harness . . . . . . . . . . . . . . . .22
8.6 To Install Locking Clip . . . . .23
8.7 UNSAFE Vehicle Belt
Lap/shoulder belt . . . . . . 32-33
11.3 With LATCH . . . . . . . . . . 34-35
12.0 Securing Your Child in the
Child Restraint . . . . . . . . . . . . 36-38
13.0 Adjust Head Support/Harness
Straps . . . . . . . . . . . . . . . . . . . . . .39
14.0 Check Harness System . . . . . . . .40
15.0 Harness Removal. . . . . . . . . . 41-45
16.0 Using Your Child Restraint WITHOUT
Built-in Harness . . . . . . . . . . . 46-48
17.0 Securing Child & Booster Seat in
Vehicle . . . . . . . . . . . . . . . . . . . . .49
26.0 To Remove Head Support and
Seat Covers. . . . . . . . . . . . . . 64-65
27.0 Replacement Parts, Warranty
and Owners Manual Storage . . . .68
Systems . . . . . . . . . . . . . 24-25
9.0 LATCH . . . . . . . . . . . . . . . . . . . . .26
9.1 What is LATCH?. . . . . . . 26-27
9.2 LATCH System . . . . . . . . . . .28
10.0 Using Child Restraint WITH
Built-in Harness . . . . . . . . . . . 29-31
18.0 Adjusting Head Support in
Booster Mode . . . . . . . . . . . . . . . .50
19.0 Removing Back Support . . . . 51-53
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
1.0 Warnings to Parents and Other Users
Failure to properly use this child restraint increases the risk of serious injury or death in a sharp
turn, sudden stop or crash. Your child’s safety depends on you installing and using this child
restraint correctly.
Even if using this child restraint seems easy to ¿gure out on your own, it is very important to READ
THE OWNER’S MANUAL and the vehicle owner’s manual.
NEVER PLACE THIS CHILD RESTRAINT IN A VEHICLE
SEATING LOCATION THAT HAS A FRONT AIR BAG. If an air
bag inÀates, it can hit the child and child restraint with great force
and cause serious injury or death to your child. Refer to your
vehicle owner’s manual for information about side air bags and
child restraint installation.
Your child’s safety depends on:
1. Choosing the correct mode of use for the child restraint depending on your child’s size.
2. Inserting the harness straps (if needed) in the proper slots for your child.
3. Selecting a suitable location for the child restraint in your vehicle.
4. Properly routing the vehicle seat belt or LATCH.
5. Properly securing the child restraint in the vehicle using a seat belt designed to restrain
both the child restraint and your child or by using LATCH. Many seat belts are NOT safe to use
with this child restraint, even though they can easily be threaded through or around the child
restraint!
6. Properly securing your child in the child restraint.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
2.3 If You Need Help
2.0 Registration Information
Please contact our Customer Service Department with any questions you may have concerning
parts, use, or maintenance. When you contact us, please have your product’s model and
manufactured in (date) ready so that we may help you ef¿ciently. These numbers can be found
on a label on the child restraint.
Model Number:
Manufactured in:
Purchase Date:
2.1 Register Your Child Restraint
Please ¿ll in the above information. The model number and manufactured in (date) can be found on
a label on the child restraint. Fill out the prepaid registration postcard attached to the harness and
mail it today.
3.0 Useful Information
3.2 Child Restraint Useful Life
3.1 CertiÀcation
Child restraints could be recalled for safety reasons. You must register this restraint to be reached
in a recall. Send your name, address, and the restraint’s model number and manufacturing date to:
THIS CHILD RESTRAINT
CONFORMS to all
STOP using child restraint and throw it away after the date
MOLDED into the child restraint.
applicable Federal Motor
Vehicle Safety Standards
and is certi¿ed for use in
motor vehicles.
Graco Children’s Products Inc.
150 Oaklands Blvd. Exton, PA, 19341
or call 1-800-345-4109
Look for the date
molded into the seat
in the location shown.
or register online at:
It is certi¿ed for use in
Aircraft only when used with
the built-in harness. When
used as a booster without
the harness, this restraint
is not certi¿ed for use in
aircraft.
2.2 For Recall Information
3.3 Second Hand Child Restraint
Graco Children’s Products Inc. advises against loaning or passing
along a child restraint.
Call the U.S. Government’s Vehicle Safety Hotline at: 1-888-327-4236
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
The locking clip is stored
on the back of the child
restraint. You will need
to use it with certain
types of vehicle seat
belts.
4.0 Features
United States Federal
Motor Vehicle Safety
Standards have de¿ned
a new system for
installing child restraints
in vehicles. The system
is called LATCH (Lower
Anchors and Tethers
for CHildren). LATCH
may ONLY be used
IN PLACE of vehicle belt
if vehicle is equipped
with LATCH anchor
points. Please refer to
vehicle owners manual
for LATCH locations in
vehicles.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
9
5.0 Assembling the Child Restraint
Adult assembly required.
1. Lay child restraint flat on back. Grab seat pad
fabric in sitting area to expose the gutters ™.
KEEP GUTTERS CLEAR
™
3. Arms should CLICK into the gutters.
Seat assembly should appear as shown œ.
MAKE SURE all hands, fingers and other objects
are clear of the gutters.
2. MAKE sure the harness straps are securely
attached within the “T”-shaped slots around the
arms as shown š.
œ
With your other hand, raise seat back so that
KEEP GUTTERS CLEAR
both arms LOCK into the gutters ›.
CLICK!
š
Harness Strap
T-slot
A r m
›
Download from Www.Somanuals.com. All Manuals Search And Download.
10
11
4. Attach 4 elastic loops from the seat pad under
6. The assembly is now complete.
the seat exactly as shown in .
5. Pull elastic loop on the seat pad through the
vehicle belt guide on side of seat and attach to
hook as shown ž. Repeat on other side.
ž
Download from Www.Somanuals.com. All Manuals Search And Download.
12
13
‡ NEVER LEAVE A CHILD RESTRAINT
UNSECURED IN YOUR VEHICLE. An
unsecured child restraint can be thrown around these parts can burn your child’s skin. Always
and may injure occupants in a sharp turn, touch the surface of any metal or plastic parts
sudden stop or crash. Remove it or make sure before putting your child in the child restraint.
that it is securely belted in the vehicle. If not
using LATCH and tether, make sure LATCH
and tether connectors are properly stored on
back of seat.
‡ THE CHILD RESTRAINT CAN BECOME
VERY HOT IF LEFT IN THE SUN. Contact with
6.0 WARNINGS
‡ NO CHILD RESTRAINT CAN GUARANTEE
PROTECTION FROM INJURY. However,
proper use of this child restraint reduces the
risk of serious injury or death to your child.
‡ DO NOT use locking clip in booster mode.
‡ According to accident statistics,
CHILDREN ARE SAFER WHEN PROPERLY
RESTRAINED IN REAR VEHICLE
SEATING POSITIONS, RATHER THAN
FRONT SEATING POSITIONS. For a
vehicle with a front passenger air bag, refer to
your vehicle owner’s manual as well as these
instructions for child restraint installation.
‡ NEVER GIVE THIS CHILD RESTRAINT to
someone else without also giving them this
manual.
‡ DO NOT INSTALL OR USE THIS CHILD
RESTRAINT UNTIL YOU READ AND
UNDERSTAND THE INSTRUCTIONS IN THIS
MANUAL AND IN YOUR VEHICLE OWNER’S
MANUAL. DO NOT let others install or use the
child restraint unless they understand how to
use it.
‡ REPLACE THE CHILD RESTRAINT AFTER ‡ NEVER USE A SECOND-HAND CHILD
AN ACCIDENT OF ANY KIND. An accident
can cause damage to the child restraint that
you cannot see.
RESTRAINT or a child restraint whose history
you do not know.
‡ NEVER LEAVE YOUR CHILD
UNATTENDED.
DO NOT USE THIS child restraint without
‡ FAILURE TO PROPERLY USE THIS CHILD
RESTRAINT INCREASES THE RISK OF
SERIOUS INJURY OR DEATH IN A SHARP
TURN, SUDDEN STOP OR CRASH. Your child
can be injured in a vehicle even if you are not
in a crash. Sudden braking and sharp turns
can injure your child if the child restraint is not
properly installed or if your child is not properly
secured in the child restraint.
‡ DO NOT MODIFY YOUR CHILD
RESTRAINT or use any accessories or parts
supplied by other manufacturers.
properly assembling it.
‡ NEVER USE CHILD RESTRAINT IF IT HAS
DAMAGED OR MISSING PARTS. Do not use
a cut, frayed or damaged child restraint
harness, LATCH belt or vehicle seat belt.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
15
7.0 Height and Weight Limitations
7.2 WITHOUT Built-in Harness
Your child must meet all requirements:
‡ Weight: 30 to 100 lbs
FAILURE TO USE CHILD RESTRAINT IN A MANNER APPROPRIATE FOR YOUR CHILD’S
SIZE MAY INCREASE THE RISK OF SERIOUS INJURY OR DEATH. Instructions for the use of
this child restraint differ greatly depending on the size of your child. Be sure you are using the child
restraint in the correct mode and with the correct features for your child.
(mass between 13.6 and 45 kg)
‡ Height: 38 to 57 inches
(96 and 145 cm) in height
‡ Approximately 3-10 years of age
‡ The shoulder belt MUST lie across child’s
shoulder as shown and the lap portion of the
belt is positioned low on the child’s hips.
‡ Child’s ears are BELOW top of head support.
If tops of ears are above top of head support,
child is too large for seat.
7.1 WITH Built-In Harness
Your child must meet all requirements:
‡ Weight: 20 to 70 lbs (mass between 9 and 31.8 kg)
‡ Height: 27 to 52 inches (69 and 132 cm) in height
‡ At least one year old and can sit upright unassisted
‡ The harness straps must be EVEN with or just
ABOVE the child’s shoulders.
If child is between 30 and 70 lbs (13.6 and
31.8 kg) and shoulders are below the
shoulder belt guides, we highly recommend
use of the built-in harness for as long as
possible (up to 70 lbs (31.8 kg).
Download from Www.Somanuals.com. All Manuals Search And Download.
16
17
8.0 Choosing an Appropriate Vehicle Seat Location
7.3 WITHOUT Back Support
8.1 Vehicle Seat Location Requirements
Your child must meet all requirements:
‡ Weigh between 40 and 120 lbs.
(mass between 18 and 54.4 kg),
‡ and are between 40 and 57 inches
(101 and 145 cm) in height,
‡ Approximately 4-10 years of age
‡ The shoulder belt MUST lie across child’s
shoulder as shown and the lap portion of the
belt is positioned low on the child’s hips.
IMPROPER PLACEMENT OF THE CHILD RESTRAINT
INCREASES THE RISK OF SERIOUS INJURY OR DEATH.
Some seating positions in your vehicle may not be safe for this child restraint. Some vehicles do
not have any seating positions that can be used safely with the child restraint. If you are not sure
where to place the child restraint in your vehicle, consult your vehicle owner’s manual or call
Graco Children’s Products Inc.,1-800-345-4109.
When sitting on the booster seat, your child’s
ears should be below the top of the vehicle seat
cushion / head support.
‡ Children are safer when properly
‡ The vehicle seat must face forward.
Do not use child restraints on rear-facing or
side-facing vehicle seats.
restrained in rear vehicle seating positions.
Whenever possible secure the child restraint in
the center position of the seat directly behind
the front seats. However, this position is
sometimes equipped with a lap belt only and
cannot be used when this child restraint is
used without the built-in harness.
Your Graco booster seat can be used with or
without the back support as long as all
requirements are met.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
19
8.2 Vehicle Seat Belt Requirements
8.4 For Built-in Harness Only
MANY SEAT BELT SYSTEMS ARE NOT SAFE TO USE
WITH THE CHILD RESTRAINT. THE VEHICLE SEAT BELT
MUST BE DESIGNED TO HOLD THE CHILD RESTRAINT
‡ Lap Belts - Manually AdMusted
When buckled, the belt is tightened
manually by pulling on the excess belt.
TIGHTLY AT ALL TIMES. Pay careful attention to these systems; some of the seat belts that
are not safe to use look very much like seat belts that are safe to use. If you are unsure,
consult your vehicle owner’s manual or call Graco Children’s Products Inc., 1-800-345-4109.
8.3 SAFE Vehicle Seat Belt Systems
‡ Lap Belts with Automatic Locking
Retractor (ALR)
The automatic locking retractor will not
permit the lap belt to lengthen once it is
buckled. Tighten the belt by feeding the belt
back into the retractor while pushing down
hard on the child restraint.
THE FOLLOWING BELT SYSTEMS CAN BE USED WITH YOUR CHILD RESTRAINT, IF the
seat location meets all other requirements of these instructions and those in your vehicle owner's
manual. LATCH can be used in place of the following vehicle belt systems if your vehicle is
equipped with LATCH anchor points. Please refer to vehicle owners manual for LATCH locations.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
21
8.5 With OR Without Built-in Harness
8.6 To Install Locking Clip
1. Tighten the buckled belt by pushing down hard on the child restraint and pulling hard on the
shoulder belt.
‡ Combination LapꢀShoulder Belt with
Locking Latch Plate
Once it is buckled, this type of belt has a
latchplate that will not allow the lap portion
of the belt to loosen. Belt is tightened by
pulling hard on the shoulder portion of the
vehicle belt while pushing down hard on
the child restraint.
2. While pushing down on seat, pinch the two straps together behind the buckle tongue. Unbuckle
the belt without allowing it to slip.
3. Attach locking clip to lap and shoulder belts as shown ™.
4. Re buckle belt. Check that lap belt does not move
by pulling hard. If belt loosens or lengthens, repeat
procedure.
Remove locking clip when not using child restraint. Store
under it’s tab on the rear of seat.
‡ Combination LapꢀShoulder Belt with
Sliding Latch Plate This belt has a
latchplate that slides freely along the belt.
Test installation to see if child restraint is secure.
If not secure, additional belt tightening may be required:
‡ This belt MUST be converted to prevent
movement of the lap portion of the belt. You
must use the locking clip provided with the
child restraint, unless your vehicle's seat
belt can be converted in another way as
described in your vehicle owner's manual.
™
1ꢀ2” (1.25 cm)
‡ Unbuckle vehicle seat belt.
‡ Hold belts together and remove locking clip.
Locking clip
‡ Shorten length of lap belt portion slightly by pulling belt
through latch plate. Re-attach locking clip.
‡ Buckle vehicle seat belt. Press child restraint further down
into vehicle seat cushion to help buckle vehicle seat belt. Test
installation to see if child restraint is secure. If not secure,
When using booster seat WITHOUT the
built-in harness, locking clip is NOT
to be used.
Download from Www.Somanuals.com. Arlel MpeaantuaalbsoSveeasrcthepAsndunDtoilwsnelcouarde..
22
23
‡ Passive Restraint -
Lap Belt with Motorized Shoulder Belt
8.7 UNSAFE Vehicle Belt Systems
DO NOT USE ANY OF THE FOLLOWING SYSTEMS TO SECURE THE CHILD RESTRAINT.
LATCH can be used IN PLACE OF the following unsafe belt systems if your vehicle is equipped
with LATCH anchor points. Please refer to the vehicle owners manual for LATCH locations.
NEVER USE unsafe belt systems.
DO NOT use vehicle belts that are
attached to the door in any way or that
move along a track to automatically
surround the passenger when the door is
closed.
‡ Lap Belts with Emergency
Locking Retractor (ELR)
This lap belt stays loose and can move
until it locks in a crash or sudden stop.
‡ Lap Belts Forward of Seat Crease
Vehicle seat belts located forward of
seat crease may not securely hold child
restraint. Check vehicle owner’s manual or
see vehicle dealer for car seat installation
requirements.
‡ Combination LapꢀShoulder Belt with
Retractor
Each strap has a retractor at one end and
is attached to the latch plate at the other
end.
‡ If approved for use with child restraint,
install child restraint and check for secure
installation by pulling child restraint front
to back. If child restraint slides forward,
DO NOT use these seat belts.
‡ Passive Restraint - Lap or Shoulder Belt
Mounted on Door
Download from Www.Somanuals.com. All Manuals Search And Download.
24
25
NOTE: Some vehicle manufacturers have lower maximum weight ratings for
LATCH anchors, so you must consult your vehicle owner’s manual or call the
vehicle manufacturer to confirm the limits on your vehicle’s LATCH anchors.
9.0 LATCH
9.1 What is LATCH?
United States Federal Motor Vehicle Safety Standards have defined a new
system for installing child restraints in vehicles. The system is called LATCH.
Use vehicle belt (not LATCH connectors) for installations with children
weighing more than 48 pounds (21.7 kg).
LATCH stands for:
Lower Anchors and Tethers for CHildren.
Vehicle Top Tether
See your vehicle
Anchor Points
LATCH in the vehicle consists of a top tether anchor point and two lower anchor
points.
owner’s manual for
exact locations, anchor
identification, and
requirements for use
Some vehicle owner manuals use the term ISOFIX to identify the new child
restraint anchor system. This child restraint with LATCH can also be used in
vehicle seating positions equipped with ISOFIX.
with a child restraint.
Vehicle Lower
Newer vehicles have one or more seating positions with LATCH anchor points.
If vehicle is equipped with LATCH, the vehicle lower anchor points may be
visible at the vehicle seat crease. If not visible, they may be marked with this
Anchor Points
Typical seat in a
passenger vehicle.
Other vehicle types
may have different
LATCH locations.
symbol
CHECK vehicle owner’s manual for vehicle top tether anchor locations. They
may be identified using one of the anchor symbols as shown
.
.
ONLY use LATCH on a child restraint in a seating position recommended by
vehicle manufacturer.
Vehicle
Seat Crease
Download from Www.Somanuals.com. All Manuals Search And Download.
26
27
9.2 LATCH System
LATCH consists of a permanently
attached lower anchor belt and a top
tether strap.
ONLY use LATCH in a seating
position recommended by vehicle
manufacturer.
10.0 Using Child Restraint WITH Built-in Harness
LATCH lower vehicle anchor points
are defined as 11 inches from the
center of one LATCH anchor to the
center of another LATCH anchor.
If allowed by your Vehicle Owners
Manual, the center seating position
maybe used if the anchor spacing is
11” or greater.
FAILURE TO PROPERLY ADJUST THE HARNESS STRAPS
FOR YOUR CHILD INCREASES THE RISK OF SERIOUS
INJURY OR DEATH IN THE EVENT OF A SHARP TURN,
SUDDEN STOP OR CRASH. Snugly adjust the belts provided with this child restraint around your
child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It
does not press on the child’s flesh or push the child’s body into an unnatural position.
š
Vehicle Top Tether
Anchor Point
Child Restraint
Top Tether
1. Loosen the harness straps by lifting the
harness adjuster lever ™ at front of seat near
the adjustment strap and pulling the straps
toward you š.
™
2. Open harness clip ›.
Vehicle Lower
Anchor Points
Lower
›
Anchor Belt
Download from Www.Somanuals.com. All Manuals Search And Download.
28
29
5. Pull on harness to make sure it is secure Ÿ.
Ÿ
3. Unbuckle harness straps œ.
REMEMBER to check the shoulder straps and
crotch strap position as your child grows and
reposition them depending on your child’s size.
The harness straps must be even with or just
above the shoulders.
œ
4. Check the crotch strap: Choose the
position that is closest to but not under
your child.
To change crotch strap position, push crotch
belt up through the bottom of the child
restraint and grab it from the top to pull out ž.
Reinsert crotch strap in the desired position.
Make sure crotch strap is not twisted when
reinserting into slot. Pull up on it to make sure
it is secure.
ž
Download from Www.Somanuals.com. All Manuals Search And Download.
30
31
4. Tighten vehicle seat belt
11.0 Securing the Child Restraint in Your Vehicle
Push down hard with your knee or free hand
in the middle of the child restraint ™.
Then pull and tighten the vehicle belt.
FAILURE TO PROPERLY SECURE THE CHILD RESTRAINT IN
THE VEHICLE INCREASES THE CHILD’S RISK OF
™
SERIOUS INJURY OR DEATH IN THE EVENT OF A SHARP
For more information on how to tighten the
belt for your seat belt system, see Section 8.0
Choosing an Appropriate Vehicle Seat Location,
p.19, or your vehicle owner’s manual.
TURN, SUDDEN STOP OR CRASH. Carefully follow these instructions and those in your vehicle
owner’s manual to be sure your child restraint is properly positioned and held tightly at all times.
11.1 Using a Child Restraint WITH a Built-in Harness
11.2 With a Vehicle Lap or Lap/shoulder Belt:
Lower anchors must be stored when using vehicle belt.
5. If a vehicle top tether anchor is available,
secure the tether to hold seat in place.
See Section 21.0 Using the Tether, page 58.
When not using the tether, hook it on the tether
storage bar on the rear of the seat, see page 59.
See Section 21.1, Storing LATCH, page 59.
1. Place the child restraint firmly against the back of a
forward-facing vehicle seat.
6. Safety Check for Secure Installation
š
Perform this test every time you drive with your child.
Twist and pull child restraint forward and to
2. Thread the seat belt through the belt slot openings:
For Lap/Shoulder belt
both sides to make sure the vehicle belt does not
lengthen or loosen and the child restraint does not
easily move. The child restraint should not move
side to side or forward more than 1 inch (2.5 cm). š.If
child restraint is loose or not secure, repeat procedure
OR find another location for the child restraint, see
Section 8.0 Choosing an Appropriate Vehicle Seat
For Lap-only belt
3. Buckle the vehicle belt. The vehicle belt should not be
twisted.
Download from Www.Somanuals.com. All Manuals Search And Download.
Location, p. 19.
32
33
6. NEVER put two LATCH connectors on
one vehicle LATCH anchor unless specifically
allowed by the vehicle manufacturer œ.
11.3 With LATCH
Use vehicle belt (not LATCH connectors) for
installations with children weighing more than
48 pounds (21.7 kg). NOTE: Some vehicle
manufacturers have lower maximum weight
ratings for LATCH anchors, so you must
consult your vehicle owner’s manual or call the
vehicle manufacturer to confirm the limits on your
vehicle’s LATCH anchors.
œ
7. All LATCH seating positions have
tether anchors. Secure the top of the seat
using the tether strap. See Section 21.0 Using
the Tether, page 58.
™
1. Unhook LATCH from storage bars on the
sides of the seat. For ease of installation, extend
LATCH to its maximum length.
8. Safety Check for Secure Installation
Perform this test every time you drive with
your child.
2. Place the child restraint firmly against the back
of a forward-facing vehicle seat.
Twist and pull child restraint forward and to
both sides to make sure the LATCH belt does
not lengthen or loosen and the child restraint
does not easily move. The child restraint
should not move side to side or forward more
than 1 inch (2.5 cm). .If child restraint is
loose or not secure, repeat procedure OR find
another location for the child restraint, see
Section 8.0 Choosing an Appropriate Vehicle
Seat Location, p. 19.
™
3. Hook LATCH Connectors to vehicle lower
anchors ™. Pull firmly on Connectors
to be sure they are attached. Belt must
lay flat and not be twisted.
š
›
4. Tighten LATCH by pushing down hard on
child restraint and pulling the adjustment belt š.
5. If you need to remove LATCH to readjust,
push button on LATCH buckle › to loosen strap.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
35
3. Fasten harness clip š. Position harness clip
at middle of child’s chest, level with
armpits.
12.0 Securing Your Child in the Child Restraint
š
FAILURE TO PROPERLY SECURE YOUR CHILD IN THE CHILD
RESTRAINT INCREASES THE RISK OF SERIOUS INJURY OR
DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP
OR CRASH. In a crash, the child restraint provides NO protection for your child unless the harness
straps are properly secured. Follow these instructions carefully to properly secure your child.
4. Tighten the harness straps by pulling the
adjustment strap on the front of the seat › .
‡ ADJUST THE HARNESS SYSTEM SNUGLY
EVERY TIME you place your child in the child
restraint.
‡ Avoid bulky clothing.
1. Place child in child restraint with child’s back flat
against back of child restraint.
›
CLICK!
2. Place harness straps over child’s shoulders
and insert tongues into buckle until they click
into place ™.
CHECK that straps are not twisted.
™
CHECK that harness is securely latched by pulling up
on straps.
DO NOT use child restraint if harness does not latch.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
37
5. The harness straps must be even with or
Must above the shoulders œ.
13.0 Adjusting Head Support/Harness Straps
When using with built-in harness always
To adjust head support/harness strap height
see page 39.
™
use one of the bottom 4 height positions.
BEFORE adjusting the head support height,
have your child lean forward slightly.
Squeeze the red adjustment handle ™ on
top of seat and pull head support up until it
snaps into one of the bottom 4 height
positions š.
œ
6. Make sure straps are flat and snug
against child’s shoulders and thighs.
You should not be able to pinch the
harness straps. A snug strap should not allow
any slack. It lies in a relatively straight line
without sagging. It does not press on the child’s
flesh or push the child’s body into an unnatural
position.
To lower, squeeze red adjustment handle
and push down.
š
CHECK to make sure it is securely snapped
into one of the bottom 4 height positions by
pulling up on head support.
CHECK that child’s ears are BELOW top of
head support. If tops of ears are above top of
head support, child is too large for harnessed
use.
The harness straps must be even with or
just above the shoulders as shown by dotted
line ›.
›
Download from Www.Somanuals.com. All Manuals Search And Download.
38
39
14.0 Check Harness System
15.0 Harness Removal
To use without built in harness:
To prevent serious injury or death:
™
1. Remove harness straps.
Open harness clip and harness buckle ™.
tꢀ,FFQꢀIBSOFTTꢀTUSBQTꢀTOVHꢀBOEꢀQPTJUJPOFEꢀPOꢀꢀ
ꢀꢀꢀTIPVMEFSTꢀXJUIꢀIBSOFTTꢀDMJQꢀBUꢀBSNꢀQJUꢀMFWFMꢁ
tꢀ%PꢀOPUꢀVTFꢀTUSBQꢀDPWFSTꢂꢀCMBOLFUTꢂꢀDVTIJPOTꢂꢀPSꢀꢀ
ꢀꢀꢀQBEEJOHꢀVOEFSꢀIBSOFTTꢀTUSBQTꢀPSꢀDIJMEꢀVOMFTTꢀꢀ
ꢀꢀꢀQSPWJEFEꢀCZꢀ(SBDPꢁ
tꢀ$IJMEꢀTIPVMEꢀCFꢀESFTTFEꢀJOꢀDMPUIJOHꢀUIBUꢀEPFTꢀOPUꢀꢀ
ꢀꢀꢀJOUFSGFSFꢀXJUIꢀCVDLMJOHꢀUIFꢀIBSOFTTꢁ
š
‡ 20 to 70 lbs (mass between 9 and 31.8 kg)
and at least one year old.
Harness straps/head support must be at or just
above shoulders.
2. Face the rear of the seat and remove the
belt straps from metal junction plate šꢀas
shown .
To adjust head support/harness strap height see
page 39.
3. Remove crotch strap by pushing the strap
retainer ›ꢀon bottom of seat, up through slot.
›
Download from Www.Somanuals.com. All Manuals Search And Download.
40
41
4. Grab the crotch strap buckle and pull it
7. On the rear of the seat, detach 2 lower seat
completely out œ.
pad elastic straps from hooks as shown in Ÿ.
œꢀ
8. Also detach the elastic straps that are
threaded through the vehicle belt guides on the
sides of the seat as shown in . Repeat on
other side.
Ÿ
5. Pull on the adjustment strap ꢀon the front
of the seat to lock the metal junction plate into
place.
ꢀ
6. Grab hold of the shoulder straps ž and pull
them out of their slots on the seat pad.
9. Pull the seat pad out of the way to reveal the
red buttons as shown in the seating area ¡ .
Slide the buttons to release the back support
from the base and lower it into a flat position.
Hold the back support to avoid it from falling
back and hitting something.
¡
Remove body support and crotch pad.
ž
Download from Www.Somanuals.com. All Manuals Search And Download.
42
43
10. Remove harness straps from arms as
shown in ¢.
12. Tuck seat pad in between the gap of the
back support and seat area of the booster seat
to allow 2 elastic straps to show at the rear of
the seat.
Store the body support, harness covers, crotch
pad cover and harness straps
in safe place for future use.
¢
Harness Strap
Arm
13. Attach 2 seat pad elastic straps onto the
hooks on the rear of the child restraint as
T-slot
shown in
.
ꢀꢁ
ꢀꢁ
14. Pull elastic strap on the seat pad through
the vehicle belt guide on side of seat and
attach to hook as shown.
ꢀꢂ
Repeat on other side
.
ꢀꢀ
11. Move seat pad fabric out of the way then
ꢀꢂ
raise seat back so that both arms LOCK into
ꢀꢀ
the gutters
.
Reverse instructions to reinstall harness.
See Section 10.0, page 29-31 for the correct
path for the harness.
You should hear a CLICK when the arms lock
into the gutters.
MAKE sure to keep the gutters clear of any
obstructions.
KEEP
GUTTERS CLEAR
Download from Www.Somanuals.com. All Manuals Search And Download.
44
45
DO NOT use shoulder belt loose
or positioned under arm ›.
16.0 Using Your Child Restraint WITHOUT Built-in Harness
FAILURE TO PROPERLY SECURE YOUR CHILD IN THE CHILD
RESTRAINT INCREASES THE RISK OF SERIOUS INJURY OR
DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP OR
DO NOT place shoulder belt behind child’s
back œ.
CRASH. In a crash, the child restraint provides NO protection for your child unless the vehicle lap/
shoulder belt is properly secured. Follow these instructions carefully to properly secure your child.
›
œ
ž
INCORRECT
INCORRECT
WARNING: Use only the vehicle lap and
shoulder belt system when restraining the child
in the booster seat. LATCH will not secure your
child in the booster seat ™.
Lap portion of lap/shoulder belt MUST be low
and snug on hips, just touching thighs.
DO NOT allow child to slide
down in booster seat .
™
Vehicle belts MUST lay flat against child and
MUST not be twisted.
If child will not keep vehicle belt properly
positioned, DO NOT use this booster seat.
Use a different child restraint system.
NEVER use a vehicle lap-only belt across front
of child š.
DO NOT position vehicle belt over top of the
armrests ž.
INCORRECT
INCORRECT
š
INCORRECT
Download from Www.Somanuals.com. All Manuals Search And Download.
46
47
Vehicle seat headrest should not create a
gap between vehicle seat and booster seat
Ÿ. The front of booster seat MUST NOT
17.0 Securing Child & Booster Seat in Vehicle
Use only the vehicle lap and shoulder belt system
when restraining the child in the booster seat.
hang over front of vehicle seat
.
1. Place booster seat firmly against the back of
a forward-facing vehicle seat equipped with a
lap/shoulder belt only.
Ÿ
š
™
2. Place child in booster seat with child’s back
flat against back of booster seat.
INCORRECT
INCORRECT
3. Position lap/shoulder belt through shoulder
belt guide ™ not underneath shoulder belt
guide š. Belt should pass over vehicle belt
guide ›. Fasten buckle and pull up on the
shoulder belt to tighten.
4. If shoulder belt lies across child’s neck,
œ
head or face, redirect belt over shoulder by
adjusting the head support setting, See page
50, Adjusting Head Support in Booster Mode.
5. The shoulder belt MUST lie across child’s
shoulders in red zone as shown œ.
Download from Www.Somanuals.com. All Manuals Search And Download.
›
48
49
18.0 Adjusting Head Support in Booster Mode
19.0 Removing Back Support
BEFORE adjusting the head support height,
have your child lean forward slightly.
™
To use booster seat WITHOUT back
support, remove harness straps if attached
(see section 15.0 Harness Removal, p.41-45)
then continue with the following steps:
Squeeze the red adjustment handle ™ on
top of seat and pull back support up until it
snaps into one of the 5 height positions š.
™
1. Detach 2 lower elastic straps from rear of
seat as shown ™.
To lower, squeeze red adjustment handle
and push down.
š
CHECK to make sure it is securely snapped
into one of the 5 height positions by pulling
up on head support.
š
2. Detach elastic strap from the hooks on the
seat pad as shown. Repeat on other side š.
The shoulder belt guides must be even with
or just above the shoulders as shown by
dotted line ›.
›
Download from Www.Somanuals.com. All Manuals Search And Download.
50
51
3. Pull the seat pad out of the way to reveal
red buttons as shown in ›. Slide the buttons
to release the back support from the base and
lower it into a flat position.
5. Once back support is separated , store
back support with all the harness straps, head
support, body support and crotch pad cover in
safe place.
When removing back support, you must
support the back support when sliding the red
buttons that disengage the back support from
the base. Make sure all hands, fingers and
other objects are not behind the back support
when removing it.
›
6. Reattach the elastic straps at the back of the
seat ž and through the vehicle belt guide on
the sides of seat Ÿ as shown.
ž
Ÿ
4. Move seat pad fabric out of the way and
squeeze red buttons together to release back
support from seat. Pull seat and back support
apart œ.
œ
7. Seat is ready to install.
To reattach back support if needed, reverse steps
from p. 53 to p. 51.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
53
2. Pass the clip and the strap through the loop
end ›ꢀas shown and pull strap up.
20.0 Securing Child in Vehicle with Shoulder Belt
Positioning Clip
The shoulder belt MUST lie across child’s
shoulders in red zone as shown ™.
›
If shoulder belt lies outside this zone, the
shoulder belt positioning clip MUST be used.
™
To attach clip to booster seat:
1. Insert the loop end of strap through the slot
on rear of seat exactly where shown š.
3. NOTE: Free end of strap œ should face
front of seat.
œ
There is a slot on each side of booster seat,
the shoulder belt positioning clip MUST be
attached through the slot closest to where the
vehicle shoulder belt lies across the child.
š
Download from Www.Somanuals.com. All Manuals Search And Download.
54
55
4. Slide the vehicle shoulder belt onto the clip as shown and pull free end of strap down ž to
tighten clip against the child’s shoulder.
5. Lap portion of lap/shoulder belt MUST be low and
snug on hips, just touching thighs.
The lap portion MUST pass through the vehicle belt guide and be positioned low on the hips.
The belt MUST NOT be twisted.
DO NOT allow child to slide down in booster seat Ÿ.
Shoulder belt
positioning clip
Shoulder belt
positioning clip
ž
Ÿ
CORRECT
REAR VIEW OF CHILD
SITTING IN SEAT
INCORRECT
Download from Www.Somanuals.com. All Manuals Search And Download.
56
57
21.0 Using the Tether
21.1 Storing Lower Anchors and Tether (LATCH)
1. For ease of storing, extend LATCH to its
maximum length.
All LATCH seating positions have tether anchors. Always use tether if a vehicle tether anchor is
available, check your vehicle owner’s manual for the tether anchor location(s). If your vehicle is
not equipped with a tether anchor, it may be possible to install one. Contact your vehicle
dealership for the proper anchor location and installation.
You may purchase tether anchor parts kit by calling Graco Customer Service at 1-800-345-4109.
Storage bars located
on each side at the
back of the seat
2. Locate the storage bars on back of
child restraint ™.
1. Check that tether is securely attached to
™
child restraint.
™
2. Fasten tether clip to anchor point ™.
3. Fasten ends of tether and lower anchors
onto their respective storage bars as shown
š.
3. Tighten adjustment belt to remove any slack š.
š
Tether
š
4. To loosen, push button while pulling on the belt
Lower
anchors
4. Tether and lower anchors storage should
look like this when complete š.
as shown ›.
›
Lower
anchors
Download from Www.Somanuals.com. All Manuals Search And Download.
58
59
22.0 Airplane Use
This restraint is certified for use in Motor Vehicles.
It is certified for use in Aircraft ONLY when used with the built-in harness.
When used as a booster WITHOUT the harness, this restraint is NOT CERTIFIED for aircraft use
because aircraft seats do not have a shoulder belt.
23.0 Accessories (on certain models ONLY)
23.1 Body Support & Harness Covers
To prevent ejection in sudden stop or crash:
‡ Never allow body support to bunch or fold behind child.
‡ Make sure that harness covers do not interfere with
placement of the chest clip at armpit level.
Important points to remember:
1. Airlines have some restrictions about the use of child restraints.
‡ Body support is not to be used by children over 35lbs.
2. Install your car seat on an airplane in the same way it is installed in an automobile with a lap
belt (see Section 11.1, Using Child Restraint WITH a Built-in Harness, p. 32).
3. Check that the airplane seat belt holds the child restraint securely in place at all times.
Download from Www.Somanuals.com. All Manuals Search And Download.
60
61
24.0 Recline Foot
25.0 Care and Maintenance
‡ Continuous use of child restraint may cause damage to vehicle seat. Use a child restraint mat,
towel or thin blanket to protect upholstery.
Your child restraint has 3 recline positions: adjust
recline foot before installing child restraint.
š
‡ Metal and plastic parts: clean with mild soap and cool water. No bleach or detergents.
1. To recline seat, pull recline handle out ™ and
tilt seat back š to extend foot as shown ›.
‡ Harness straps and LATCH straps: spot clean with damp sponge. Do not immerse the straps in
water. Doing so may weaken the straps.
™
›
‡ Buckle should fasten with a “click”, if not, rinse buckle with warm water. DO NOT USE SOAPS
or LUBRICANTS. DO NOT use household detergents. Never lubricate buckle.
‡ If buckle or harness adjuster sticks or will not remain tight, check for foreign objects such as
food, dirt, etc. Remove objects with tweezers and/or clean with a cotton swab. If you cannot get
the harness to remain tight with the buckle securely locked, do not use this child restraint.
2. To set seat to upright position, pull recline
handle out œꢀand tilt seat forward to retract
foot ž.
œ
ž
Download from Www.Somanuals.com. All Manuals Search And Download.
62
63
Hook and loop
attachment tape
26.0 To Remove Head Support and Seat Covers
š
SEAT COVER: clean with a damp sponge
using mild soap and cool water. If necessary,
cover may be removed for cleaning.
HEAD SUPPORT COVER: clean with a damp
sponge using mild soap and cool water. If
necessary, cover may be removed for
cleaning.
™
1. Remove harness and crotch straps (see
Section 15.0, Harness Removal, p.41-45).
1. Remove harness and crotch straps (see
Section 15.0, Harness Removal, p.41-45).
2. Remove elastic loops from seat as indicated
in š.
Hook and loop
attachment tape
2. Remove elastic loops from head support as
indicated in ™.
3. Remove seat cover as shown.
3. Remove head support cover as shown.
4. Machine wash cover in cold water on
delicate cycle and drip-dry. DO NOT USE
BLEACH.
4. Machine wash cover in cold water on
delicate cycle and drip-dry. DO NOT USE
BLEACH.
5. To put the seat cover back on, reverse
preceding instructions.
5. To put the head support cover back on,
reverse preceding instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
64
65
Notes
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
66
67
|