USER’S GUIDE
V:1153-1008-10
TDE2480
24” Class TV/DVD Combo
For the most up-to-date version of this User’s Guide, go to www.gpx.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1. Read these Instructions.
FCC Warnings
WARNING: Changes or modifications to this unit not expressly
2. Keep these Instructions.
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
3. Heed all Warnings.
4. Follow all instructions.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings
• The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed on
apparatus.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un
vase, ne doit être placé sur l’objet.
11. Only use attachments/accessories specified by the
manufacturer.
• Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus
from the mains completely, the mains plug should be disconnected
form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facilement
accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débranchée
du secteur.
Use only with a cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
12.
• Battery shall not be exposed to excessive heat such as sunshine, fire
or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la
lumière du soleil, au feu ou autres choses de semblable.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
• Caution marking is located at the rear or back of the apparatus.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil
• The marking information is located at the rear or back of apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière de
l’appareil.
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Rovi Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by
Rovi Corporation. Reverse engineering and disassembly are prohibited.
Customer Support: 1-888-999-4215
GPX
3
Download from Www.Somanuals.com. All Manuals Search And Download.
24”Class TV/DVD Combo
Features
Included
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
23.6”LED display
•
•
Stand and 3 screws
Remote control: requires 2 AAA batteries
(included)
DVD player: DVD, DVD R/RW
CD player: CD, CD-R/RW, JPEG CD
Resolution: 1920 x 1080
Max color: 16.7 million
Brightness: 300 cd/m2
Contrast: 1000 : 1
Response time: <5ms
Viewing angle: H=170, V=160
V-chip
Closed captioning
Electronic program guide
Sleep timer
Multi-language OSD
RF input
2 HDMI inputs
2 RCA audio inputs
VGA/PC video input
3.5mm PC audio input
2 Composite video inputs
2 Component video inputs
USB port
Memory card reader
AC power: requires an AC power cable
(included)
•
AC power cable
* Please note, LCD panel specifications are subject to change without notice.
4
GPX
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
24” Class TV/DVD Combo 4
Features
Included
Table of Contents 5
Introduction 6
Setup 8
Power
Remote Power
Connecting the Stand
Television Setup 9
Connecting a TV Antenna
Connecting Basic Cable
Connecting a Set-Top Box
Auto Scanning for Channels
Television 10
Channel List
Saving a Channel as a Favorite
Viewing Favorites
Parental Controls
Accessing the TV Menu
Setting the Clock
DVD 11
Loading and Playing a Disc
Programming a DVD
Accessing the DVD Setup Menu
Memory Card Reader 12
Connecting a Memory Card
Accessing the Connected Memory Card
USB Port 13
Connecting a USB Thumb Drive
Accessing the Connected USB Thumb Drive
Connecting Other Devices 14
Connecting a Set-Top Box
Connecting a Gaming Device
Connecting a DVD Player or VCR
Connecting a Computer
Company Information 16
International Support
Contact Information
Green Initiative
Customer Support: 1-888-999-4215
GPX
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
EJECT
Press to eject
the loaded
disc.
PLAY/PAUSE EJECT
PLAY/PAUSE
Press to play or
pause a loaded
disc.
VOLUME
Press to adjust Press to adjust
the volume.
CHANNEL
MENU
Press to view
the television
menu.
SOURCE
Press to adjust Press to power
between
the available
sources.
POWER
the television
channel.
the television
off or on.
STEREO
HEADPHONE
JACK
USB PORT
RCA STEREO
AUDIO INPUT 2
COMPOSITE
VIDEO INPUT 2
DISC DRIVE
COMPONENT
VIDEO INPUT 2
3.5mm PC AUDIO
INPUT
MEMORY
CARD READER
RCA STEREO
AUDIO INPUT 1
VIDEO INPUT
1
USB
AC IN
Y
Pb
Pr
TV ANTENNA
DRIVE
COMPOSITE
VIDEO INPUT 1
RF INPUT
COMPONENT
VIDEO INPUT 1
VGA/PC VIDEO
INPUT
HDMI INPUTS
AC POWER
INPUT
SERVICE PORT
Used for
firmware
upgrades.
6
GPX
Download from Www.Somanuals.com. All Manuals Search And Download.
EJECT
Press to eject a disc from the DISC DRIVE.
NUMBER KEYPAD
POWER
EJECT
POWER
MUTE
Press to turn the television off and on.
DISPLAY
Press to view the on-screen display.
MUTE
Press to mute the volume.
16:9/4:3/FAV LIST
Press to adjust the aspect ratio. Press to
access your favorites list on the television.
PICTURE
Press to adjust the picture settings.
PICTURE
VOLUME
Press to adjust the volume.
SOUND
SOUND
SLEEP
Press to adjust the sound settings.
SOURCE
Press to adjust the source.
SLEEP
Press to set the sleep timer.
ARROW/ENTER
Press to navigate DVD and system menus,
and to make selections.
ZOOM/CHANNEL LIST
Press to zoom in or out on a loaded DVD.
Press to view a list of available channels on
the television.
DVD
16:9/4:3
ZOOM
CH LIST CHANNEL
VOLUME FAV LIST
CHANNEL
DISPLAY
Press to adjust the channel.
SAP
In TV mode, press to switch to an alternate
audio option when supported.
MENU
SOURCE
MENU
Press to access the TV’s menu.
ASPECT
Press to adjust the aspect ratio.
EXIT
Press to exit the current on-screen menu.
ENTER
CC
GUIDE
Press to turn closed captioning off or on.
Press to view the on-screen guide.
SAP
EXIT
BACKWARD/FORWARD
Press to search through an individual
chapter or track.
USB/SD
Press to access USB and SD modes.
CC
ASPECT
GUIDE
USB/SD
NEXT
PREVIOUS/NEXT
Press to skip between chapters or tracks on
the loaded disc.
STOP
BACKWARD FORWARD PREVIOUS
Press to stop a disc during play.
PROG
Press to program a loaded disc to play titles,
chapters, or tracks in a specified order.
DVD MENU
Press to access the loaded DVD’s menu.
STOP
PROG
PLAY/PAUSE DVD MENU DVD SETUP
ANGLE
TITLE
A-B
GOTO
DVD SETUP
Press to access the DVD setup menu.
PLAY/PAUSE
Press to play or pause a loaded disc.
SUBTITLE
AUDIO
REPEAT
GOTO
SUBTITLE
Press to adjust the current subtitle settings
for the loaded DVD.
Press to go to a specified title, chapter,
track, or time on the loaded disc.
REPEAT
ANGLE
Press to view alternate angles on supported
DVDs.
Press to repeat a title, chapter, track, or
entire disc.
AUDIO
TITLE
Press to view the title menu on the loaded
DVD.
Press adjust the current audio settings for
the loaded DVD.
A-B
Press to create a repeating loop on a
specified section of a loaded DVD.
Customer Support: 1-888-999-4215
GPX
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Power
Plug the attached AC cord into a standard AC
power outlet to power the television.
VIDEO INPUT
1
USB
DRIVE
AC IN
Y
Pb
Pr
TV ANTENNA
Remote Power
Requires 2, AAA size, batteries (included)
Connecting the Stand
Requires stand and 3 machine screws
(all included)
1. Insert a single machine screw through
the bottom of the stand and up into the
television. Tighten by hand using a philips-
head screw driver.
2. Insert the remaining two screws through
the back of the stand and into the television.
Tighten by hand using a philips-head screw
driver.
8
GPX
Download from Www.Somanuals.com. All Manuals Search And Download.
Television Setup
Connecting a TV Antenna
Connecting a Set-Top Box
Requires a TV antenna (not included).
Requires a Set-Top Box (not included).
1. Connect a VHF, UHF, or HDTV antenna to the
If your Set-Top Box has an HDMI Output:
RF INPUT on the television.
•
Connect the HDMI output on the Set-Top Box
to the HDMI INPUT on the television using
an HDMI cable (not included).
The Auto Channel Scan must be run before any
channels can be viewed on the television.
2. Press the SOURCE button and switch to TV
If your Set-Top Box has a Composite Video
Output:
mode.
•
Connect the video output on the Set-Top
Box to the COMPOSITE VIDEO INPUT on
the television using an A/V RCA cable (not
included). Connect the audio output on the
Set-Top Box to the RCA STEREO AUDIO
INPUT on the television.
3. Press the MENU button.
4. Use the ARROW buttons to select Channel in
the on-screen menu. Press the ENTER button.
5. Use the ARROW buttons to select Signal Type
in the on-screen menu. Press the ARROW
buttons to change the Signal Type to Air.
If your Set-Top Box has a Component Video
Output:
6. Use the ARROW buttons to select Auto
Channel Search in the on-screen menu. Press
the ENTER button to automatically scan for
available channels.
•
Connect the component video output on
the Set-Top Box to the COMPONENT VIDEO
INPUTS on the television using a component
RCA cable (not included). Connect the
Connecting Basic Cable
audio output on the Set-Top Box to the RCA
STEREO AUDIO INPUT on the television.
Requires a cable connection.
1. Connect a cable to the RF INPUT on the
After connecting your Set-Top Box:
television.
•
Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
The Auto Channel Scan must be run before any
channels can be viewed on the television.
2. Press the SOURCE button and switch to TV
Auto Scanning for Channels
mode.
The Auto Channel Scan must be run before any
channels can be viewed on the television.
3. Press the MENU button.
4. Use the ARROW buttons to select Channel in
the on-screen menu. Press the ENTER button.
1. Press the SOURCE button and switch to TV
mode.
5. Use the ARROW buttons to select Signal Type
in the on-screen menu. Press the ARROW
buttons to change the Signal Type to Cable.
2. Press the MENU button.
3. Use the ARROW buttons to select CHANNEL
in the on-screen menu. Press the ENTER
button.
6. Use the ARROW buttons to select Auto
Channel Search in the on-screen menu. Press
the ENTER button to automatically scan for
available channels.
4. Use the ARROW buttons to select Auto
Channel Search in the on-screen menu. Press
the ENTER button to automatically scan for
available channels.
Customer Support: 1-888-999-4215
GPX
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Television
Channel List
Parental Controls
Press the CHANNEL LIST button on the remote
to view a list of available channels on the
television.
1. In TV mode, press the MENU button.
2. Use the ARROW buttons to select Parental
Control in the on-screen menu. Press the
ENTER button.
If there are no channels in your channel list, you
may need to re-run the Auto Scan for Channels.
(see page 9)
3. The default passcode for the parental lock is:
0 0 0 0
From the V-CHIP settings you can lock TV and
movies that have specific ratings.
Saving a Channel as a Favorite
1. In TV mode, press the MENU button.
Use the Front Panel Lock to lock the buttons on
the television. (The remote will still work if the
Front Panel Lock is checked)
2. Use the ARROW buttons to select Channel in
the on-screen menu. Press the ENTER button.
3. Use the ARROW buttons to select Channel
Setting in the on-screen menu. Press the
ENTER button.
Accessing the TV Menu
1. In TV mode, press the MENU button.
4. Use the ARROW buttons to select the
Channel Number you want to save as a
favorite.
To exit the TV menu, press the EXIT button on
the remote.
Setting the Clock
5. Use the ARROW buttons to select Favorite
Channel. Press the ENTER button to save the
selected channel as a favorite.
1. In TV mode, press the MENU button.
2. Use the ARROW buttons to select Setup in
the on-screen menu. Press the ENTER button.
Viewing Favorites
1. In TV mode, press the FAVORITES LIST
button on the remote to access your favorites
list on the television.
3. Use the ARROW buttons to select Clock in
the on-screen menu. Press the ENTER button.
4. Use the ARROW buttons to select your time
2. Use the ARROW/ENTER buttons to highlight
zone.
and select a channel from the favorites list.
5. Use the ARROW buttons to highlight Setup
Time.
6. Use the left and right ARROW buttons and
ENTER button to adjust and save the date
and time.
10 GPX
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD
Loading and Playing a Disc
1. Press the SOURCE button to switch to DVD
mode.
2. Insert a DVD or CD into the DISC DRIVE, label-
side facing the rear of the TV.
The loaded disc will begin playing
automatically.
3. If the loaded disc does not automatically
play, press the PLAY/PAUSE button.
Programming a DVD
1. Follow the instructions for Loading and
Playing a Disc.
2. Press the PROGRAM button on the remote.
3. Use the NUMBER KEYPAD and ARROW
buttons to enter title (TT) and chapters (CH)
from the loaded DVD in the order you want
them to play.
Disc title and chapter information can be
obtained by pressing the DISPLAY button
during DVD playback.
4. Press the PLAY/PAUSE button or use the
ARROW buttons to highlight the on-screen
PLAY button and press ENTER to begin
playing the programmed DVD.
Accessing the DVD Setup Menu
1. To access the DVD Setup Menu, press the
DVD SETUP button on the remote.
To exit the DVD setup menu, press the DVD
SETUP button.
Customer Support: 1-888-999-4215
GPX 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory Card Reader
Connecting a Memory Card
1. Load an SD, MS, or MMC memory card into
the MEMORY CARD READER as shown in
the image to the right.
Accessing the Connected Memory Card
1. Follow the instructions for Connecting a
Memory Card.
2. Press the SOURCE button to switch to DVD
mode.
3. Press the USB/SD button on the remote to
switch to CARD mode.
4. Use the ARROW/ENTER buttons to select
and play content from the connected
memory card.
12 GPX
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Port
Connecting a USB Thumb Drive
1. Connect a USB thumb drive to the USB PORT
as shown in the image to the right.
Accessing the Connected USB Thumb Drive
1. Follow the instructions for Connecting a USB
Thumb Drive.
2. Press the SOURCE button to switch to DVD
mode.
3. Press the USB/SD button on the remote to
switch to USB mode.
4. Use the ARROW/ENTER buttons to select
and play content from the connected USB
thumb drive.
Customer Support: 1-888-999-4215
GPX 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Devices
Connecting a Set-Top Box
Connecting a DVD Player or VCR
•
You will need: a set-top box, composite
and RCA stereo cables or component and
RCA stereo cables or an HDMI cable. (not
included)
•
You will need: a DVD player or VCR,
composite and RCA stereo cables or
component and RCA stereo cables or an
HDMI cable.
•
•
Connect the set-top box’s audio and video
outputs to the corresponding audio and
video inputs on the television.
Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
•
•
Connect the DVD player or VCR’s audio and
video outputs to the corresponding audio and
video inputs on the television.
Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
Connecting a Gaming Device
Connecting a Computer
•
You will need: a gaming device, composite
and RCA stereo cables or component and
RCA stereo cables or an HDMI cable. (not
included)
Connect the gaming device’s audio and video
outputs to the corresponding audio and
video inputs on the television.
Press the SOURCE button to switch between
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and
VGA to match the connection used.
•
•
•
•
You will need: a PC with a VGA output, and a
VGA cable. (not included)
Connect the computer’s VGA output to the
VGA/PC INPUT on the television.
Power the television on and press the
SOURCE button to switch to the VGA Mode.
Audio from the connected PC can be input
to the television through the TV’s PC AUDIO
INPUT by using a 3.5mm audio cable (not
included).
•
•
14 GPX
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support: 1-888-999-4215
GPX 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Company Information
International Support
Green Initiative
To download this User’s Guide in English,
Spanish, or French, visit the support section at
Para transferir esta guía de usuario en inglés,
español, o francés, visite la sección de la ayuda
Pour télécharger ce guide de l’utilisateur en
anglais, espagnol, ou français, visitez la section
Environmental Commitment to ‘Protect for Today
and Sustain for Tomorrow’
2009 marked the official launch of DPI, Inc.’s
corporate campaign for a greener and cleaner
world. DPI is building upon environmental
initiatives introduced at all of their facilities
to help formulate and sustain significant and
important conservation efforts within its
manufacturing and marketing communities.
In addition to targeting and selecting energy
efficient product features, and structuring ‘green
office’procedures, other initial program efforts
include:
Contact Information
Phone:
1-888-999-4215
Email:
Parts Email:
Website:
•
•
Reduction of all packaging sizes
Recyclable plastics for clamshell packages,
with a plan to eventually replace plastic with
recyclable paper
•
•
Recycled fiber board in place of the polyfoam
in packing boxes
Recycled plastics in place of the virgin
material in product construction
Copyright © 2010 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners.
Specifications are subject to change without notice
Download from Www.Somanuals.com. All Manuals Search And Download.
|