General Tire Sander 15 220 User Manual

Ro ta ting & o sc illa ting e ffe c t e nsure s

e xc e p tio na l finishing re sults.

Pre c isio n g ro und c a st iro n ta b le .

On-b o a rd sid e m o unte d sp ind le sto ra g e .

Tilting ta b le fo r sa nd ing b e ve le d p a rts.

2” d ia m e te r d ust o utle t with 2” to 4”

a d a p te r fitting inc lud e d .

5 inte rc ha ng e a b le sp ind le a sse m b lie s:

1/ 4", 1/ 2", 5/ 8", 1 1/ 2", 2" d ia .with 100 g rit

sa nd p a p e r.

1 1/ 2" & 2" sp ind le s c o m e with rub b e r

d rum s.

Inc lud e s 4 ta b le inse rts to a c c o m o d a te

d iffe re nt sp ind le size s.

OSCILLATIONS PER MINUTE

LENGTH OF OSCILLATION

15⁄16” (24 m m )

TABLE SIZE

14 1⁄2” x 14 1⁄2” (368 x 368 m m )

TABLE TILT

0° - 45°

TABLE HEIGHT FROM BOTTOM OF BASE

18 5⁄16” (465 m m )

SPINDLE SIZES

1⁄4” TO 2” (6.2 TO 50.8 m m )

DUST CHUTE OUTLET

2” (50.8 m m )

SPINDLE SPEED

1720 RPM

BASE DIMENSIONS (L x W

14 1⁄2” x 14 1⁄2” (368 x 368 m m )

MOTOR

1⁄2 HP, 110 V, 7.5 A

WEIGHT

81 LBS (37 kg )

REVISION 3 FEB 13/ 07

Download from Www.Somanuals.com. All Manuals Search And Download.

Rules for Safe Operation

To help ensure safe operation, please take a moment to learn the machine’s applications and limita-

tions, as well as potential hazards. General International disclaims any real or implied warranty and

hold itself harmless for any injury that may result from the improper use of it’s equipment.

1. Do not operate this sander when tired, distracted or

under the effects of drugs, alcohol or any medica-

tion that impairs reflexes or alertness.

14. Do not sand without a table insert in place. If an

insert must be removed for maintenance or spindle

changes make sure it is properly re-installed before

re-starting the machine.

2. Keep the work area well lit, clean and free of debris.

15. Hold the workpiece firmly against the table and use

suitable support if the workpiece does not have a

flat surface.

3. Stay alert! Give your work your undivided attention.

Even a momentary distraction can lead to serious

injury.

16. Never stand on or lean against this machine.

Serious injury could occur if the sander is tipped

over or if the sanding spindle is unintentionally

contacted.

4. Do not wear loose clothing, gloves, bracelets,

necklaces, or other jewelry. Wear face, eye, ear,

respiratory and body protection devices. Wear

protective hair covering to contain long hair and

wear non-slip footwear.

17. Use only recommended parts and accessories. The

use of parts or accessories NOT recommended by

General® International may result in a risk of injury.

5. Keep hands well away from the spindle and all

moving parts. Do not clear chips and sawdust

away with hands. Use a brush.

18. Make sure the machine is properly grounded. If

equipped with three-prong plug, it should be

plugged into a three-pole electrical receptacle.

Never remove the third-prong.

6. Fine particulate dust is a carcinogen that can be

hazardous to health. Always work in a well ventila-

ted area and whenever possible use a dust

collector to minimize health hazards.

19. Always disconnect the unit from the power source

before changing accessories such as sanding

spindles or sleeves or before performing any main-

tenance and adjustments or if the machine will be

left unattended.

7. Be sure the spindle has achieved full operating

speed before beginning to sand.

8. Be aware of the direction of the spindle rotation

before feeding the workpiece and always feed the

workpiece against the rotation.

20. Make sure that switch is in the “Off” position before

plugging in to a power source.

9. Do not force the spindle. It will perform better and

21. Be sure that all adjustment tools, wrenches or other

clutter are removed from the machine and safely

stored before turning on the unit.

safer at the rate for which it was designed.

10. Keep children and shop visitors at a safe distance

when the unit is running – do not permit them to

operate the machine.

22. Avoid working from awkward or off balance

positions. Do not overreach and always keep both

feet firmly on the floor.

11. Do not operate with a damaged spindle or with a

damaged or torn sanding sleeve.

23. Do not use this spindle sander for other than it’s

intended use. If used for other purposes, GENERAL®

INTERNATIONAL disclaims any real or implied

warranty and holds itself harmless for any injury,

which may result from that use.

12. Be sure the sanding spindle is securely installed in

the machine before starting the machine.

13. Never leave the machine unattended while run-

ning or with the power on.

Download from Www.Somanuals.com. All Manuals Search And Download.

ELECTRICAL REQUIREMENTS

Before connecting the machine to the power source, ver-

ify that the voltage of your power supply corresponds

with the voltage specified on the motor I.D. nameplate.

A power source with greater voltage than needed can

result in serious injury to the user as well as damage to

the machine. If in doubt, contact a qualified electrician

before connecting to the power source.

In all cases, make certain the receptacle is pro-

perly grounded. If you are not sure, have a quali-

fied electrician check the receptacle.

This tool is for indoor use only. Do not expose to

rain or use in damp locations.

GROUNDING INSTRUCTIONS

In the event of an electrical malfunction or short circuit,

grounding reduces the risk of electric shock to. This

motor of this machine is wired for 110V single phase

operation and is equipped with a 3-conductor cord

and a 3-prong grounded plug to fit a grounded type

socket. Do not remove the the 3rd prong (grounding

pin) to make it fit into an old 2-hole wall socket. If an

adaptor plug is used it must be attached to the metal

screw of the socket. The wall socket must be properly

installed and grounded. Note: The use of an adaptor

plug is illegal in some areas. Check you local codes.

DO NOT MODIFY THE PLUG PROVIDED.

If it will not fit your receptacle, have the proper recep-

tacle installed by a qualified electrician.

CHECK with a qualified electrician or service person if

you do not completely understand these grounding

instructions, or if you are not sure the tool is properly

grounded.

This tool must be grounded while in use to protect

the operator from electrical shock.

EXTENSION CORDS

USE ONLY 3-WIRE EXTENSION CORDS THAT HAVE 3-PRONG GROUNDING PLUGS AND 3-POLE RECEPTACLES THAT

ACCEPT THE TOOL’S PLUG. REPAIR OR REPLACE DAMAGED OR WORN CORD IMMEDIATELY.

If you find it necessary to use an extension cord with your machine make sure the cord rating is suitable for the

amperage listed on the motor I.D. plate. An undersized cord will cause a drop in line voltage resulting in loss of

power and overheating. The accompanying chart shows the correct size extension cord to be used based on cord

length and motor I.D. plate amp rating. If in doubt, use the next heavier gauge. The smaller the number the

heavier the gauge.

EXTENSION CORD LENGTH

AMPERES

(AMPS)

25 feet

50 feet

75 feet

100 feet

150 feet 200 feet

< 5

5 to 8

8 to 12

12 to 15

15 to 20

21 to 30

* Based on limiting the line voltage drop to 5V at 150% of the rated amperes.

NR = Not Recommended

Download from Www.Somanuals.com. All Manuals Search And Download.

VERTICAL OSCILLATING SPINDLE SANDER

15-220

IDENTIFICATION OF MAIN PARTS AND COMPONENTS

ACCESSORY STORAGE

BASE

TABLE INSERT

TABLE TILT LOCK LEVER

SANDING SPINDLE

CAST-IRON TABLE

SWITCH ASSEMBLY

Download from Www.Somanuals.com. All Manuals Search And Download.

UNPACKING AND SET-UP

ADDITIONAL REQUIREMENTS FOR SET UP

SET UP SAFETY

Serious personal injury could occur if you con-

nect the machine to the power source before

you have completed the set up process. DO NOT

connect the machine to the power source until

instructed to do so.

The MODEL 15-220M1 is a heavy machine

(81 lbs shipping weight–37kg). Do not over-

exert. Arrange to have help nearby and ready

for unpacking and set up.

• Machinists square

• Medium Phillips Screwdriver

• An extra person for help lifting

UNPACKING

Carefully unpack and remove the unit and its components from its shipping container and check for missing or

damaged items as per the list of contents below.

NOTE: Please report any damaged or missing items to your GENERAL® INTERNATIONAL distributor immediately.

LIST OF CONTENTS

Separate and verify that all parts are in your accessories

hardware bags.

QTY

MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

RED STOP COVER . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

DUST HOSE ADAPTOR 2” TO 4” . . . . . . . . . . . . . . . . . .1

SANDING SPINDLE HARDWARE

— Sanding drum spindle assembly 1 1/2” . . . . . .1

— Sanding drum spindle assembly 2” . . . . . . . . .1

— Sanding sleeve 5/8” . . . . . . . . . . . . . . . . . . . . . . .1

— Sanding sleeve 1/2” . . . . . . . . . . . . . . . . . . . . . . .1

— Sanding sleeve 1/4” . . . . . . . . . . . . . . . . . . . . . . .1

— Spindle 5/8” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

— Spindle 1/2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

— Spindle 1/4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

TABLE INSERT 2”(oblong) . . . . . . . . . . . . . . . . . . . . . .1

TABLE INSERT 3/4” (oblong) . . . . . . . . . . . . . . . . . . . .1

TABLE INSERT 3/4”(round -*^{Mounted on the machine}) . . . . .1

TABLE INSERT 2” (round) . . . . . . . . . . . . . . . . . . . . . . .1

10-12 mm WRENCH . . . . . . . . . . . . . . . . . . . . . . . . . . .1

14-17 mm WRENCH . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEAN UP

Be sure to work in a well ventilated area for the

entire clean up process.

Before starting the clean up process make sure the

machine is not plugged into a power source. Failure

to comply may lead injury or cause damage to the

machine.

All unpainted surfaces are covered with

protective

coating that prevents rust from forming during shipping and

storage. Peel off the plastic cover from the table and remove

this protective coating by rubbing with a rag dipped in

kerosene, mineral spirits or paint thinner. (Dispose of potentially

flammable solvent-soaked rags according to manufacturer’s

safety recommendations.)

A putty knife, held flat to avoid scratching the surface, may also

be used to scrape off the coating followed by clean-up with

solvent.Avoid rubbing the machine’s painted surfaces, as many

solvent-based products will remove paint.

For optimum performance from your machine, make sure you

clean all metal surfaces of the spindles with a mild solvent or

kerosene.

To prevent rust, apply a light coating of paste wax or regular applications of General International “Top Saver” item

# GC-010 or similar after-market protectants to the table surface.

ASSEMBLY INSTRUCTIONS

The unit should be installed on a flat, sturdy and stable surface able to support the weight of the machine.

Never install the machine over the edge of a table

or workbench.

Never lift the machine by the table; hold and lift

from the insets on the cabinet.

Make sure that the switch is in “OFF” position and that the power

cord is unplugged & install the red stop switch cover plate.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALL THE SANDING SLEEVES ONTO THEIR CORRESPONDING SPINDLES

Step 1

Step 2

For 1/4, 1/2, & 5/8 spindles loosen the screw on the

Slide the sanding sleeve onto the spindle completely.

Note: the sleeve should slide under the bracket

clamp as shown. Re-tighten the screw on the bracket

clamp to secure the sleeve in place.

bracket clamp (

) at the bottom of the spindle.

Step 3

Step 4

Double check that the sleeve is now on the spindle

securely by pulling on the sleeve to make sure it does

not slide off the spindle.

For the 1 1/2”and 2”spindles slide the sleeve onto the

spindle.

TIGHTEN

LOOSEN

Step 5

Step 6

Using the supplied 12 mm wrench tighten the nut on

the top of the spindle by turning counter clockwise

(reverse thread).

Double check that the sleeve is now on the spindle

securely by pulling on the sleeve to make sure it does

not slide off the rubber drum. If the sleeve slides on

the drum, continue tightening the nut (step 5) in 1/2

turn increments as needed.

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORY STORAGE

SPINDLES

TABLE INSERT PLATES

Place the drums into their storage space on the right

side of the machine.

Store the table insert plates in the storage slots on the

left side of the machine.

INSTALLING SPINDLES ON THE MACHINE

Note: Reverse threads are used to attach the spindle to the machine.

Make sure that the switch is in “OFF” position and that the power cord is unplugged.

If installed, remove the table insert to allow better

access the spindle seat.

Step 1

Select the desired spindle and while holding the

spindle seat in place with a 17 mm wrench, screw the

threaded end into the spindle seat counter clockwise

(reverse threads) until hand tight.

LOOSEN

TIGHTEN

Step 2

Using the two 17 mm wrenches tighten the spindle no more than another 1/2 turn.

NOTE: Do not overtighten the spindle in the seat or it may be very difficult to take off later.

BEFORE STARTING THE MACHINE:

•

Make sure the spindle is securely installed onto the arbor.

Make sure that the corresponding table insert is installed. See the accompanying SELECTION GUIDE (page 10) to

select the correct INSERT TABLE for the spindle being used.

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECTION GUIDE FOR TABLE INSERTS

This machine is supplied with 5 spindles, and four table

inserts. The spindle diameters range from 1/4" to 2".

When changing spindles, the table insert will need to

be changed to the matching size. Each plate has

There are 2 insert plates with oblong openings and 2

with round openings. The oblong insert plates are

used when the table is tilted for bevel sanding.

notch (

) to fit the alignment pin (

) in the table to

ensure that it is properly fitted and installed in the table

opening.

FAILURE TO USE THE PROPER INSERT WITH THE CORRESPONDING SPINDLE MAY RESULT IN INJURY AND/OR DAMAGE TO

THE MACHINE OR THE WORKPIECE.

The following chart explains which inserts can be used for different diameter spindles.

SPINDLE DIAMETER

TABLE INSERT (OPENING SHAPE/SIZE)

1/4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#86 (ROUND) & #87 (OBLONG) -SMALL

1/2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#86 (ROUND) & #87 (OBLONG) -SMALL

5/8” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#86 (ROUND) & #87 (OBLONG) -SMALL

1-1/2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#85 (ROUND) & #84 (OBLONG) -LARGE

2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#85 (ROUND) & #84 (OBLONG) -LARGE

RECOMMENDED ADJUSTMENTS

SETUP FOR 90º SANDING

Step 1

Step 2

Loosen both locking levers, position the table at 0° and

re-tighten the locking levers.

With a spindle installed, place a square on the table.

Rest the long section of the square against the

sanding spindle. The square should be flat against

the table and the spindle from all four sides.

Download from Www.Somanuals.com. All Manuals Search And Download.

90° TABLE

STOP ROD

Step 3

Step 4

If the table needs adjustment loosen both lock levers

and readjust the table position until the square is flat

against the table and the sanding drum. To allow

for more or less rear tilt adjust the table stop rod as

needed.

Make sure the pointer reads 0°. If the pointer needs

to be adjusted loosen the screw and adjust to the

correct position.

Step 5

Once the table has been adjusted and locked in place at 90° adjust the 90° table stop rod to butt against the under-

side of the table allowing you to return to 90° repeatedly without further adjustments.

SETUP FOR BEVEL SANDING

1. Make sure the correct oblong opening table insert is in

place. See the accompanying SELECTION GUIDE

(page 10) to select the correct TABLE INSERT for the

spindle being used.

2. Loosen both locking levers and tilt the table until the

pointer is at the desired angle.

3. Hold the table in place and tighten both locking levers.

CHANGING SANDING SLEEVES

Make sure that the switch is in “OFF” position and that the power cord is unplugged.

Note: Installing or changing sanding sleeves is best performed with the spindle removed from the machine.

Refer to page 8 - “Installing the sanding sleeves” for step by step instructions.

REPLACEMENT SANDING SLEEVES

Replacement sleeves can be purchased in varying grits (depending on availability) from any local tool or abrasives

dealer in the following sizes:

•

1/4" DIAMETER X 6 " LONG

1/2" DIAMETER X 6 " LONG

5/8" DIAMETER X 6 " LONG

•

1-1/2" DIAMETER X 5 1/2 " LONG

2” DIAMETER X 5.5” LONG

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECT TO A DUST COLLECTOR

Before sanding connect the machine to a dust

collection system.

Always turn on the dust collector before starting the

sander and always stop the sander before turning

off the dust collector.

•

There is a 2”diameter dust outlet on the rear of the machine

allowing for the connection to a dust collector (not included).

A 2” TO 4” DUST HOSE ADAPTOR is also included to facilitate

(if needed) connection to a standard 4” dust collection

hose.

•

Be sure to use appropriate size hose and fittings (not included).

and check that all connections are sealed tightly to mini-

mize airborne dust.

If you do not already own a dust collection system consi-

der contacting your GENERAL® INTERNATIONAL distributor

for information on our complete line of dust collection

systems or visit our Web Site at: www.general.ca

OPERATING INSTRUCTIONS

BASIC FUNCTIONS OF THIS MACHINE

This machine has been designed for sanding or polishing round or curved surfaces on wood, plastic, or metal

materials. It is ideal for use in smaller woodworking projects in a hobbyist/home shop environment.This machine is not

designed with a continuous duty rating or for industrial applications.

CONNECTING TO A POWER SOURCE

Plug the machine into a proper receptacle – before connecting to the power source make sure that the switch is in

the “off” position and that the power supply is of the same type as that stamped on the I.D. nameplate of the motor.

Running on low voltage will damage the motor.

To avoid risk of shock or fire do not operate the unit with a damaged power cord or plug. Replace damaged cord

or plug immediately.

ON/OFF SWITCH & SAFETY PIN

The switch assembly is equipped with a lock-out safety pin.

When the pin is installed through the green “on” button, the

machine cannot be started.

To start the machine, lift the red stop switch panel and remove

the lock-out pin. Lower the stop panel and push the green “ON”

button. Wait for the spindle to reach full speed before sanding.

To stop the machine, push on the RED “STOP” panel and wait for

the spindle to come to a complete stop.

When you have finished using the machine be sure to re-install

the lock-out pin and unplug the machine from the power

source.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATIONS

Before operating this machine, make sure you

Be sure the sanding spindle is securely installed in

the machine.

have read this manual attentively! Failure to read

and understand the instructions, warnings and safe-

ty guidelines provided in this manual may lead to

serious injury and / or damage to machine or the

workpiece.

Make sure the machine is installed on a flat, sturdy

and stable surface able to support the weight of the

machine and the workpiece to be sanded.

Make sure the table tilt locking levers are secured

and that the table is locked in place at the desired

angle or tilt.

1. Select and install a spindle that is smaller than the curve to be sanded.

2. Use an appropriate table insert plate that comes closest to the spindle without touching it.

3. Make sure that spindle is properly installed in the spindle seat. With the supplied wrenches tighten the nut

slightly beyond hand-tight.

NOTE: Spindle threads are reversed. Turn Clockwise to loosen and counter clockwise to tighten.

NOTE: Never over tighten; it may be difficult to remove the spindle later.

4. When table is set at a 90° angle, sanding may be done

from any corner, or location on the table.

5. When the table is positioned at any angle other than 90°,

sanding should only be performed with the workpiece

positioned below the centre point of the table (photo)

6. Make sure the table tilt locking levers are secured and that

the table is locked in place at the desired angle or tilt.

7. Always loosen both table tilt locking levers before changing the angle position of the table. Never force the

table. If it does not tilt easily it may be that the locking levers may still be engaged.

8. Hold the workpiece firmly and work from a stable standing position.

9. To achieve the best finish results and to ensure maximum sanding sleeve life, slowly move the workpiece back

and forth across the entire surface of the sanding spindle.

MAINTENANCE

Make sure the switch is in the OFF position and unplug the unit from the power source before performing any

maintenance.

•

All bearings are sealed and permanently lubricated. No further lubrication is needed.

Periodically inspect all hardware, fittings and fasteners that may have loosened due to vibration – re-tighten as

needed.

•

To minimize airborne dust particles periodically inspect all dust collection fittings – re-tighten as needed.

Inspect the ON/OFF SWITCH for damage before each use.

Keep the machine CLEAN and FREE OF DUST to help dissipate heat.

Check and if necessary replace all damaged TABLE INSERTS, SPINDLES or SANDING SLEEVES

Periodically inspect the power cord and plug for damage. If necessary replace the power cord and the plug at

the first signs of visible damage.

•

Use only recommended parts and accessories. The use of parts or accessories NOT recommended by General

International may result in a risk of injury or damage to the machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECOMMENDED OPTIONAL

ACCESSORIES FOR YOUR

OSCILLATING SPINDLE SANDER

We offer a large variety of products to help you increase pro-

ductivity, accuracy and safety when using your oscillating spin-

dle sander. Here’s a small sampling of accessories available

from your local General International dealer.

ITEM #

DECRIPTION

15-211A Sanding Sleeve 1/4" X 6"

15-211B Sanding Sleeve 1/4" X 6"

15-211C Sanding Sleeve 1/4" X 6"

15-211D Sanding Sleeve 1/4" X 6"

40 Grit

60 Grit

80 Grit

100 Grit

120 Grit

150 Grit

15-211E

15-211F

Sanding Sleeve 1/4" X 6"

15-212A Sanding Sleeve 1/2" X 6"

15-212B Sanding Sleeve 1/2" X 6"

15-212C Sanding Sleeve 1/2" X 6"

15-212D Sanding Sleeve 1/2" X 6"

40 Grit

60 Grit

80 Grit

100 Grit

120 Grit

150 Grit

15-212E

15-212F

Sanding Sleeve 1/2" X 6"

15-213A Sanding Sleeve 5/8" X 6"

15-213B Sanding Sleeve 5/8" X 6"

15-213C Sanding Sleeve 5/8" X 6"

15-213D Sanding Sleeve 5/8" X 6"

40 Grit

60 Grit

80 Grit

100 Grit

120 Grit

150 Grit

15-213E

15-213F

Sanding Sleeve 5/8" X 6"

15-214A Sanding Sleeve 1 1/2" X 5 1/2 40 Grit

15-214B Sanding Sleeve 1 1/2" X 5 1/2 60 Grit

15-214C Sanding Sleeve 1 1/2" X 5 1/2 80 Grit

15-214D Sanding Sleeve 1 1/2" X 5 1/2 100 Grit

Stand

#15-230

15-214E

15-214F

Sanding Sleeve 1 1/2" X 5 1/2 120 Grit

Sanding Sleeve 1 1/2" X 5 1/2 150 Grit

15-215A Sanding Sleeve 2" X 5 1/2"

15-215B Sanding Sleeve 2" X 5 1/2"

15-215C Sanding Sleeve 2" X 5 1/2"

15-215D Sanding Sleeve 2" X 5 1/2"

40 Grit

60 Grit

80 Grit

100 Grit

120 Grit

150 Grit

15-215E

15-215F

Sanding Sleeve 2" X 5 1/2"

Dust Collector

“TOP SAVER”

cleaner #GC-010

We have a wide selection

of dust collectors to suit all

your shop needs. Dust

collectors contribute

to a cleaner and more

healthful workshop

All in one, table top rust

remover and lubricant.

/Reduces friction and pre-

vents binding. / Removes

and inhibits rust and

corrosion. /Repels dust

and moisture.

environment.

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

15-220

PART N0.

REF. N0.

DESCRIPTION

SPECIFICATION

QTY

15220-01

15220-02

15220-03

15220-04

15220-05

15220-06

15220-07

15220-08

15220-09

15220-10

15220-11

15220-12

15220 -13

15220-14

15220-15

15220-16

15220-17

15220-18

15220-19

15220-20

15220-21

15220-22

15220-23

15220-24

15220-25

15220-26

15220-27

15220-28

15220-29

15220-30

15220-31

15220-32

15220-33

15220-34

15220-35

15220-36

15220-37

15220-38

15220-39

15220-40

15220-41

15220-42

15220-43

15220-44

15220-45

15220-46

15220-47

15220-48

15220-49

15220-50

30201001G

30201001A

S1006P1

BASE

TOP PLATE

STRAIN RELIEF

POWER CORD

PHILLIPS HEAD SCREW

RUBBER FOOT

WASHER

L0000000

S0030622M

10107098

S0210400

S0110600M

S0230300

S0030318

M0000000

S0430650

S0040415M

30202001

S0050610M

30202002

S0110800M

30202003

S0210400

S012500M

C1106804

30202004

CL106006

S0520059

30202005

S0050506M

S05ETW04

30202020

30202006P

30202007P

S0010615M

30202008P

30204010

S0230400

S0400415

CL106001

S0521200

S0530028

S0230506

S0210500C

30202009

30202014

S0030304

30203001

30203003

30203003A

S0020825M

30300028

S0110600

40501011

(W/PLUG)

M6 X 1 X 22L

1/4" X 19MM

M6X1.0

3/16"

LOCK NUT

LOCK WASHER

PHILLIPS HEAD SCREW

MOTOR

KEY

SET SCREW

WORM GEAR

SET SCREW

TRANSMISSION ROD

HEX. NUT

CONNECTING ROD

WASHER

HEX NUT

BEARING

SPINDLE SEAT

BEARING

RETAINING RING- C TYPE

CONNECTING ROD NUT

SET SCREW

RETAINING RING-E TYPE

CONNECTING SPINDLE

WHEEL SEAT

WHEEL

SET SCREW

WHEEL ARBOR

ARBOR COVER

LOCK WASHER

KEY

3/16"-24UNC X 3/4" 2

6 X 6 X 50

M4 X 0.7 X 15L

M6 X 1.0 X 10L

M8 X 1.25 X 75L

M8 X 1.25

1/4" X 19MM

6804ZZ

6006ZZ

M5 X 0.8 X 6L

M6 X 1.0 X 10L

1/4"

4 X 4 X 15

6001ZZ

STW-12

R-28

BEARING

RETAINING RING C-TYPE

LOCK WASHER

FLAT WASHER

OIL CAP

REAR OIL CAP

PHILLIPS HEAD SCREW

MAIN CASTING

L BRACKET

CAP SCREW

90° TABLE STOP ROD

HEX NUT

TABLE TILT GUIDE BRACKET WITH SCALE (RIGHT)

5/16"

5/16" X 18 X 2T

3/16"-24UNC X 1/4" 2

(RIGHT)

(LEFT)

M8 X 1.25 X 20L

M8 X 1.25 X 110L

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

15-220

PART N0.

REF. N0.

DESCRIPTION

SPECIFICATION

QTY

15220-51

15220-52

15220-53

15220-54

15220-55

15220-56

15220-57

15220-58

15220-60

15220-61

15220-62

15220-63

15220-64

15220-64A

15220-65

15220-66

15220-67

15220-68

15220-69

15220-70

15220-71*

15220-72*

15220-73*

15220-74*

15220-75*

15220-76

15220-77

15220-78

15220-79

15220-80

15220-81

15220-82

15220-83

15220-84

15220-85

15220-86

15220-87

15220-88

15220-89

15220-90

15220-91

15220-92

15220-93

15220-94

15220-95

15220-96

15220-97

40501011A

30204013G

S0010516M

S0050606M

10102022

S0220400

S0030510M

30203005

30203006

30203007

S0030508M

S0520028

30203008

30203008G

S0400550

30203015

30203014

30203017

30203018

30203019

TABLE TILT GUIDE BRACKET

LOCKING LEVER

PHILLIPS HEAD SCREW

SET SCREW

ANGLE POINTER

SPROCKET WASHER

PHILLIPS HEAD SCREW

DUST PORT

SPINDLE

COVER

SET SCREW

SNAP RING

5/8” SPINDLE

KEY

DRUM

1/2" SPINDLE

1/4" SPINDLE

1/2" CLAMP

(LEFT)

M6 X 1.0 X 6L

1/4"

M5 X 0.8-10L

22 X 119

M5 X 0.8-8L

5 X 5 X 50

1-1/2"

SEE LIST ON PG. 14 FOR OPTIONAL/REPLACEMENT SANDING SLEEVES

30203019A

30203019B

30204001

20301002

20801002

20301044

S02 10500

S0110500

30204003

30204004

30204005

30204006

S0310312

30201003

10105091

J8010004

J2091001

WG000001

5/8" CLAMP

1/4" CLAMP

MAIN TABLE

LOWER FOLLOWER PLATE

UPPER FOLLOWER PLATE

WASHER

1-1/2" & 2”

1-1/2"

5/16" X16

5/16" NUT (LH)

TABLE INSERT (OBLONG)

TABLE INSERT (ROUND)

TABLE INSERT (OBLONG)

ALIGNMENT SPRING PIN

COMBINATION WRENCH

WARNING LABEL

3/4"

3 X 12M/M

14/17MM

10/12

(NOT SHOWN)

I.D LABEL

SWITCH ASSEMBLY W/ COVER PLATE

RED STOP SWITCH COVER PLATE

SWITCH BOX

SAFETY LOCK-OUT PIN W/CHAIN

2” TO 4” DUST HOSE ADAPTOR

WG000002

WG000003

Download from Www.Somanuals.com. All Manuals Search And Download.

15-220

8360 Champ-d’Eau, Montreal (Quebec)

Canada H1P 1Y3

Tel.: (514) 326-1161

Fax : (514) 326-5565 Parts & Service

Fax : (514) 326-5555 Order Desk

orderdesk@general.ca

www.general.ca

IMPORTANT: When ordering replacement parts, always give the model number, serial number of

the machine and part number. Also a brief description of each item and quantity

desired.

Download from Www.Somanuals.com. All Manuals Search And Download.

Extron electronic Network Card MTP Series User Manual
Extron electronic Switch VTG 150 User Manual
Fisher Paykel Cooktop CT2802 User Manual
Fostex DVR D 15 User Manual
Fujitsu Scanner FI 7160 User Manual
Fujitsu Server RX200 User Manual
Furuno SONAR CH 32 User Manual
GE Clothes Dryer WBVH5200J User Manual
Gefen Log Splitter gtb hd4k2k 142 User Manual
GE Washer EWA3000 User Manual