GENERAC
The Reliable Ones
SE10000
Portable Generator Owner’s Manual
DANGER! This generator is designed for outdoor use only. Never use this generator inside any building
or enclosure including the generator compartment of a recreational vehicle (RV). Carbon monoxide
poisoning, fire and/or an explosion may result. No user performed modifications, including venting of
exhaust and/or cooling ventilation, will eliminate the danger. Always have at least two feet of clearance on
all sides of the generator even while operating the unit outdoors.
DANGER! You must isolate the generator from the electric utility by opening the electrical system’s
main circuit breaker or main switch if this unit is used for backup power. Failure to isolate the generator
from the power utility may result in injury or death to electric utility workers and damage to the
generator due to a backfeed of electrical energy.
The Emission Control System for this generator is warranted for standards set by the
Environmental Protection Agency. For warranty information refer to the engine Owner’s manual.
Model No. 1339–0 (10000 Watt AC Generator) Manual No. B4472 Revision 2 (8/17/1999)
Visit our Generac website: www.generac–portables.com
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
• The generator produces a very powerful voltage that
GROUNDING THE
GENERATOR
The National Electric Code requires the frame and
external electrically conductive parts of the generator
be properly connected to approved earth ground.
Local electrical codes may also require proper
grounding of the unit. For this purpose, a grounding
wing nut (Figure 1) is provided on the cradle.
can cause serious injury or death by electrocution.
Never touch bare wires or receptacles. Never permit
a child or any unqualified person to operate the
generator.
• Never handle any kind of electrical cord or device
while standing in water, while barefoot or while
hands or feet are wet.
• Use a ground fault circuit interrupter (GFCI) in any
damp or highly conductive area (such as metal
decking or steel work).
Figure 1 — Location of Grounding Wing Nut
• Never use worn, bare, frayed or otherwise damaged
electrical cords with the generator.
• Gasoline is highly FLAMMABLE and its vapors
are EXPLOSIVE. Never allow smoking, open
flames, sparks or heat in the vicinity while
handling gasoline. Avoid spilling gasoline on a hot
engine. Comply with all laws regulating storage and
handling of gasoline.
• Do not overfill the fuel tank. Allow room for fuel
expansion. If tank is overfilled, fuel can overflow
onto a hot engine and cause a FIRE or an
EXPLOSION.
Grounding Wing Nut
• Never store a generator with fuel in the tank where
gasoline vapors might reach an open flame, spark
or pilot light (as on a furnace, water heater, clothes
dryer). FIRE or an EXPLOSION may result.
Generally, connecting a No. 12 AWG (American Wire
Gauge) stranded copper wire to the grounding wing
nut and to an earth-driven copper or brass grounding
rod (electrode) provides adequate protection against
electrical shock. However, local codes may vary
widely. Consult with a local electrician for grounding
requirements in your area. Be sure to keep the ground
wire attached while you connect the electrode.
• Do not insert any object through cooling slots of the
engine. You could damage the unit or injure
yourself.
• The unit requires an adequate flow of cooling air for
its continued proper operation. Never operate the
unit inside any room or enclosure where the free
flow of cooling air into and out of the unit might be
obstructed. Allow at least 3 feet of clearance on
all sides of generator or you could damage the unit.
Properly grounding the generator helps prevent
electrical shock if ground fault conditions exists in the
generator or in connected electrical devices. Proper
grounding also helps dissipate static electricity, which
often builds up in ungrounded devices.
• Never operate the generator:
in rain; in any enclosed compartment; if connected
electrical devices overheat; if electrical output is
lost; if engine or generator sparks; if flame or smoke
is observed while unit is running; if unit vibrates
excessively.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
Your generator requires some assembly and is ready
for use after it has been properly serviced with the
recommended oil and fuel.
CHECK BATTERY / ATTACH
NEGATIVE BATTERY WIRE
The battery on the generator is fully charged, sealed
and pre-installed except for the negative (black)
battery cable.
If you have any problems with the assembly of
your generator, please call the generator helpline
at 1-800-270-1408.
IMPORTANT: Any attempt to run the engine before it
has been serviced with the recommended oil will
result in an engine failure.
To install:
• Remove nut on the negative battery terminal.
• Slide the negative battery cable over the screw on
the terminal (Figure 2).
REMOVE GENERATOR
FROM CARTON
Figure 2 — Negative Battery Connection
• Set the palleted carton on a rigid flat surface.
• Carefully cut bands around the shipping carton.
• Lift carton off the generator.
• Remove all packing material, carton fillers, etc.
• Remove the generator from the shipping pallet.
CARTON CONTENTS
Check all contents. If any parts are missing or
damaged, call the generator helpline at
1-800-270-1408. Contents include:
• 10,000 watt generator
• Generator owner’s manual
• Engine owner’s manual
• 2 Bottles of SAE 30 engine oil (28 oz.)
• Oil fill spout
• Reattach nut and tighten.
• Ensure the connections to the battery and generator
are tight and secure.
• 125 Volt, 30 Amp plug
• 125 Volt, 20 Amp plug
• 120/240 Volt, 30 Amp plug
• Wheel kit
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
WHEEL KIT INSTALLATION
You will need a 13mm metric box, open end or socket
wrench to install this kit.
5. Install other wheel in the same manner.
Install Wheel Kit as follows: (Figure 3)
6. Secure the vibration mount on the support leg
with lock nut, washer, and 30mm capscrew.
Fasten the support leg to the bottom of the
generator cradle, using 20mm capscrews, lock
washers and flat washers.
1. Place the bottom of the generator cradle on a flat,
even surface. It may help to raise the cradle on
temporary blocks.
2. Slide axle through both axle mounting brackets on
cradle frame.
7. Position the handle below the muffler bracket on
the engine side of the generator. Attach the
handle with 45mm capscrews and lock nuts.
3. Slide spacer over each end of axle.
4. Install the wheel. Secure wheel on axle with
retaining pin and washer. Be sure to install the
wheel with the raised hub inboard.
8
Recheck all nuts to make sure they are tight and
secure. Remove the temporary blocks.
Figure 3 — Wheel Kit
Handle
45mm Capscrew
Locking Nut
Support Leg
Locking
Nut
Flat Washer
Vibration
Mount
Axle
M8 Flat
Washer
Lock Washer
Spacer
20mm Capscrew
30mm
Capscrew
Washer
Wheel
Retaining Pin
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
KNOW YOUR GENERATOR
Read this owner’s manual and safety rules before operating your generator.
Compare the illustrations with your generator to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
Fuel Shut Off Valve
Fuel Tank
Air Filter
(on top of engine)
Circuit Breakers (AC)
Key Switch
120 Volt AC, 20 Amp
Duplex Receptacle
Choke
120 Volt AC, 20 Amp
Locking Receptacle
Oil Filter
120 Volt AC, 30 Amp
Locking Receptacle
120/240 Volt AC,
50 Amp Receptacle
120/240 Volt AC, 30 Amp
Locking Receptacle
120 Volt AC, 20 Amp Duplex Receptacle — Each
supplies electrical power for the operation of 120 Volt
AC, 20 Amp, single phase, 60 Hz electrical lighting,
appliance, tool and motor loads.
120/240 Volt AC, 50 Amp Receptacle — Supplies
electrical power for the operation of 120/240 Volt AC,
50 Amp, single phase, 60 Hz welder or motor loads.
Air Filter — Filters intake air as it is drawn into the
120 Volt AC, 20 Amp Locking Receptacle —
Supplies electrical power for the operation of 120 Volt
AC, 20 Amp, single phase, 60 Hz electrical lighting,
appliance, tool and motor loads.
engine.
Choke — Used to start a cold engine.
Circuit Breakers (AC) — Each receptacle is provided
with a circuit breaker to protect the generator against
electrical overload. Breakers are "push to reset" type.
120 Volt AC, 30 Amp Locking Receptacle —
Supplies electrical power for the operation of 120 Volt
AC, 30 Amp, single phase, 60 Hz electrical lighting,
appliance, tool and motor loads.
Fuel Shut–Off Valve — Always have the fuel shut-off
valve closed when engine is not running.
Fuel Tank — Tank holds 10 U.S. gallons of unleaded
gasoline.
120/240 Volt AC, 30 Amp Locking Receptacle —
Supplies electrical power for the operation of 120
and/or 240 Volt AC, 30 Amp, single phase, 60 Hz
electrical lighting, appliance, tool and motor loads.
Key Switch — Used to start engine. Always have key
switch in the “Stop” position when not in use.
Oil Filter — Filters engine oil to prolong engine life.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
can attract moisture, which leads to separation and
BEFORE STARTING THE
GENERATOR
formation of acids during storage. Acidic gas can
damage the fuel system of an engine while in storage.
To avoid engine problems, the fuel system should be
emptied before storage of 30 days or longer. See
“Storage” on page 12. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
Add Engine Oil
For your convenience, an oil filler spout has been
supplied with your generator. This cap fits over a
standard bottle of oil and allows for easy access to the
oil fill.
TO START THE ENGINE
See engine owner’s manual for oil recommendations
and fill instructions.
WARNING! Never start or stop engine with
electrical devices plugged into the panel
receptacles and turned on. You could damage
both the generator and the electrical devices.
Add Gasoline
DANGER! NEVER fill fuel tank indoors.
NEVER fill fuel tank when engine is running or
hot. DO NOT light a cigarette or smoke when
filling the fuel tank.
• Unplug all electrical loads from unit’s receptacles
before starting the engine.
• Make sure the unit is in a level position.
• Open the fuel shut–off valve (Figure 5).
DANGER! Do not overfill the fuel tank. Always
leave room for expansion.
Figure 5 — Fuel Shut–off Valve
• Use regular UNLEADED gasoline in the generator.
DO NOT use premium gasoline. DO NOT mix oil
with gasoline. DO NOT overfill the gas tank.
• Clean area around fuel fill cap; remove cap.
• Fill fuel tank with clean, fresh, unleaded gasoline.
Be careful not to overfill. Allow 1/2" of tank space for
fuel expansion (Figure 4).
• Pull the choke knob to close. If the engine is warm,
or the ambient temperature is high, pull the choke
knob half–way, or keep it fully open (Figure 6).
Figure 4 — Fuel Expansion Space
Figure 6 — Choke Knob
• Install fuel cap and wipe up any spilled gasoline.
IMPORTANT: It is important to prevent gum deposits
from forming in essential fuel system parts such as
the carburetor, fuel filter, fuel hose or tank during
storage. Also, experience indicates that alcohol-
blended fuels (called gasohol, ethanol or methanol)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
IMPORTANT! Do not overload the generator! Do
DANGER! Engine exhaust contains carbon
monoxide, a colorless and odorless gas which
causes unconsciousness and death. Never
run engine indoors or in poorly ventilated
areas.
not overload individual panel receptacles! These
outlets are protected against overload with push-to-
reset-type circuit breakers. If amperage rating of any
circuit breaker is exceeded, that breaker opens and
electrical output to that receptacle is lost. Read “Don’t
Overload the Generator” on page 11 carefully.
DANGER! Burn hazard. Temperature of
muffler and nearby areas may exceed 150°F
(65°C). Do not touch these areas on the
generator.
If the Engine Will Not Start
Refer to the engine owner’s manual.
• Turn key switch to the “Start” position (Figure 7).
STOPPING THE ENGINE
Figure 7 — Key Switch
• Remove all electrical loads connected to unit’s
receptacles. Never start or stop engine with
devices plugged in and turned on.
• Let engine run at no-load for 30 seconds to stabilize
the unit’s internal temperatures.
• Turn the key switch to the “Stop” position.
• Close the fuel valve.
STOPPING THE ENGINE
WITH THE FUEL VALVE
This procedure eliminates fuel from the carburetor.
Use this method to stop the generator if you plan to
store the generator over a long period. Fuel will clog
the internal passages of carburetor if allowed to
remain for an extended period.
IMPORTANT: Do not operate the electric starter
continuously for more than 5 seconds, even if the
engine does not start. Extended cranking can damage
the starter motor.
NOTE: If the engine fails to start, set the key to the
“Run” position and wait for about 10 seconds before
retrying.
IMPORTANT: Never turn the key switch to the “Start”
position while the engine is running. You could
damage the starter motor.
• Unplug all electrical loads connected to the unit’s
receptacles. Never start or stop engine with
devices plugged in and turned on.
• When the engine starts, gradually open choke by
pushing the choke knob in and keep it fully opened
while running.
• Let engine run at no-load for 30 seconds to stabilize
the internal temperatures of engine and generator.
• Close the fuel valve while the engine is running and
wait until the engine stops.
• Set the key switch to the “Stop” position after the
engine quits.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
Connecting Electrical Loads
• DO NOT connect 240 Volt loads to 120 Volt
receptacles.
120 Volt AC, 20 Amp Receptacle
Use a NEMA L5-20 plug with this receptacle. Connect
a 3-wire cord set rated for 125 Volts AC at 20 Amps
(or greater) to the plug (Figure 9).
• DO NOT connect 3-phase loads to the generator.
• DO NOT connect 50 Hz loads to the generator.
Figure 9 — 120 Volt, 20 Amp, Locking Receptacle
• Let engine stabilize and warm up for a few minutes
after starting.
• Plug in and turn on the desired 120 Volt or 240 Volt,
single phase, 60 Hz electrical loads.
• Add up the rated watts (or amps) of all loads to be
connected at one time. This total should not be
greater than (a) the rated wattage/amperage
capacity of the generator or (b) circuit breaker rating
of the receptacle supplying the power. See “Don’t
Overload the Generator” on page 11.
RECEPTACLES
Use this receptacle to operate 120 Volt AC, 60 Hz,
single phase loads requiring up to 2400 watts
(2.4 kW) of power at 20 Amps. The outlet is protected
by a 20 Amp push-to-reset circuit breaker.
120 Volt AC, 20 Amp, Duplex
Receptacle
Use each receptacle to power 120 Volt AC, single
phase, 60 Hz electrical loads requiring up to a
combined 2400 watts (2.4 kW) or 20 Amps of current
(Figure 8).
120 Volt AC, 30 Amp Receptacle
Use a NEMA L5-30 plug with this receptacle. Connect
a 3-wire cord set rated for 125 Volts AC at 30 Amps
(or greater) to the plug (Figure 10).
Figure 8 — 120 Volt, 20 Amp, Duplex Receptacle
Figure 10 — 120 Volt, 30 Amp, Locking Receptacle
Each outlet is protected against overload by a 20 Amp
push-to-reset circuit breaker. Use only high quality,
well-insulated, 3-wire grounded cord sets rated for
125 Volts at 20 Amps (or greater).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
Use this receptacle to operate 120 Volt AC, 60 Hz,
240 Volt AC, 50 Amp Receptacle
Use a NEMA 14–50 plug with this receptacle.
Connect a 4-wire cord set rated for 250 Volts at
50 Amps to the plug (Figure 12).
single phase loads requiring up to 3600 watts
(3.6 kW) of power at 30 Amps. The outlet is protected
by a 30 Amp push-to-reset circuit breaker.
120/240 Volt AC, 30 Amp Receptacle
Figure 12 — 120/240 Volt, 50 Amp, Receptacle
Use a NEMA L14-30 plug with this receptacle.
Connect a suitable 4-wire grounded cord set to the
plug and to the desired load (Figure 11). The cord set
should be rated for 250 Volts at 30 Amps (or greater).
Figure 11 — 120/240 Volt, 30 Amp, Locking Receptacle
Use this receptacle to operate 240 Volt AC, 60 Hz,
single phase loads requiring up to 10,000 watts
(10.0 kW) of power.
Use this receptacle to operate 120 Volt AC, 60 Hz,
single phase loads requiring up to 3600 watts
(3.6 kW) of power at 30 Amps or 240 Volt AC, 60 Hz,
single phase loads requiring up to 7200 watts
(7.2 kW) of power at 30 Amps. The outlet is protected
by a 30 Amp push–to–reset circuit breaker.
CAUTION! Although this outlet states it has a
240 Volt AC, 50 Amp rating (up to 12,500
watts), the generator is only rated for 10,000
watts. Powering loads that exceed the wattage/
amperage capacity of the generator can
damage it and cause serious injuries.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
• If wattage is not given, multiply volts times ampere
rating to determine watts (volts x amps = watts).
DON’T OVERLOAD THE
GENERATOR
Overloading a generator in excess of its rated wattage
capacity can result in damage to the generator and to
connected electrical devices. Observe the following to
prevent overloading the unit:
• Some electric motors, such as induction types,
require about three times more watts of power for
starting than for running. This power surge lasts
only seconds when starting such motors. Make sure
to allow for this high starting wattage when selecting
electrical devices to connect to your generator:
• Add up the total wattage of all electrical devices to
be connected at one time. This total should NOT be
greater than the generator’s wattage capacity.
1. Figure the watts needed to start the largest motor.
2. Add to that figure the running watts of all other
connected loads.
• The rated wattage of lights can be taken from light
bulbs. The rated wattage of tools, appliances and
motors can usually be found on a data plate or
decal affixed to the device.
The Wattage Reference Guide below (Figure 13) is
provided to assist you in determining how many items
your generator can operate at one time.
Figure 13 — Wattage Reference Guide
Device
Running Watts
Device
Running Watts
*Air Conditioner (12,000 Btu)..........................1700
*Air Conditioner (24,000 Btu)..........................3800
*Air Conditioner (40,000 Btu)..........................6000
Battery Charger (20 Amp) ................................500
Belt Sander (3") ..............................................1000
Chain Saw ......................................................1200
Circular Saw (6-1/2") ...........................800 to 1000
*Clothes Dryer (Electric).................................5750
*Clothes Dryer (Gas) ........................................700
*Clothes Washer.............................................1150
Coffee Maker..................................................1750
*Compressor (1 HP) .......................................2000
*Compressor (3/4 HP) ....................................1800
*Compressor (1/2 HP) ....................................1400
Curling Iron.......................................................700
*Freezer............................................................700
*Dehumidifier....................................................650
Disc Sander (9") .............................................1200
Edge Trimmer...................................................500
Electric Blanket.................................................400
Electric Nail Gun.............................................1200
Electric Range (per element)..........................1500
Electric Skillet .................................................1250
*Furnace Fan (3/5 HP) .....................................875
*Garage Door Opener ...........................500 to 750
Hair Dryer .......................................................1200
Hand Drill.............................................250 to 1100
Hedge Trimmer.................................................450
Impact Wrench..................................................500
Iron .................................................................1200
*Jet Pump.........................................................800
Lawn Mower ...................................................1200
Light Bulb..........................................................100
Microwave Oven..................................700 to 1000
*Milk Cooler ....................................................1100
Oil Burner on Furnace ......................................300
Oil Fired Space Heater (140,000 Btu) ..............400
Oil Fired Space Heater (85,000 Btu) ................225
Oil Fired Space Heater (30,000 Btu) ................150
*Paint Sprayer, Airless (1/3 HP)........................600
Paint Sprayer, Airless (handheld) .....................150
Radio .......................................................50 to 200
*Refrigerator .....................................................700
Slow Cooker .....................................................200
*Submersible Pump (1-1/2 HP) ......................2800
*Submersible Pump (1 HP) ............................2000
*Submersible Pump (1/2 HP) .........................1500
*Sump Pump .......................................800 to 1050
*Table Saw (10")................................1750 to 2000
Television...............................................200 to 500
Toaster...............................................1000 to 1650
Weed Trimmer..................................................500
* Allow 3 times the listed watts for starting these devices.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
more than 30 days, use the following guidelines to
prepare it for storage.
GENERAL MAINTENANCE
RECOMMENDATIONS
Generator Storage
• Clean the generator as outlined in “To Clean the
Generator.”
The Owner/Operator is responsible for making sure
that all periodic maintenance tasks are completed on
a timely basis; that all discrepancies are corrected;
and that the unit is kept clean and properly stored.
Never operate a damaged or defective generator.
• Check that the cooling air slots and openings on the
generator are open and unobstructed.
• Remove the negative battery cable from the battery
to prevent the battery from being depleted.
Engine Maintenance
See your engine owner’s manual for instructions.
DANGER! The battery is water based. If you
are storing the generator in an area that will go
below freezing, you must remove the battery
and store it separately in an area that will not
freeze. If you allow the battery to freeze, the
water in it will expand and crack open the
battery spilling the contents.
Generator Maintenance
Generator maintenance consists of keeping the unit
clean and dry. Operate and store the unit in a clean
dry environment where it will not be exposed to
excessive dust, dirt, moisture or any corrosive vapors.
Make sure the cooling air slots in the generator do not
become clogged with leaves or other foreign material.
• Prepare the engine in accordance with the storage
instructions in the engine owner manual.
NOTE: DO NOT use a garden hose to clean
• Let the unit completely cool for at least 5 minutes
before placing any cover over the unit.
generator. Water can enter the engine fuel system
and cause problems. In addition, if water enters the
generator through the cooling air slots, some water
will be retained in the voids and cracks of the rotor
and stator winding insulation. Water and dirt buildup
on the generator internal windings will eventually
decrease the insulation resistance of these windings.
• Store the unit in a clean dry place.
Other Storage Tips
• Do not store gasoline from one season to another.
• Replace your gasoline can if it starts to rust. Rust
and/or dirt in a gasoline can cause problems when
you use that fuel with this unit.
To Clean the Generator
• Use a damp cloth to wipe exterior surfaces clean.
• Store in clean and dry area.
• Soft, bristle brush may be used to loosen caked on
dirt or oil.
SPECIFICATIONS
• A vacuum cleaner may be used to pick up loose dirt
and debris.
Rated Maximum Continuous
AC Power Output.............................10,000 Watts
Rated Voltage ..................................120/240 Volts
Rated Maximum Current at
240 Volts.......................................41.6 Amps
Rated Maximum Current at
• Low pressure air (not to exceed 25 psi) may be
used to blow away dirt. Inspect cooling air slots and
opening on generator. These openings must be kept
clean and unobstructed.
120 Volts.......................................83.3 Amps
Phase...............................................1
Rated AC Frequency .......................60 Hertz
Number of Rotor Poles ....................2
Driven Speed of Rotor .....................3600 rpm
STORAGE
The generator should be started at least once every
seven days and allowed to run at least 30 minutes. If
this cannot be done and you must store the unit for
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
NOTES
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
TROUBLESHOOTING
Problem
Engine is running, but no AC
output is available.
Cause
Solution
1. Circuit breaker is open.
1. Reset circuit breaker.
2. Poor connection or defective cord 2. Check and repair.
set.
3. Connected device is bad.
3. Connect another device that is in
good condition.
4. Fault in generator.
4. Contact Generac service facility.
Engine runs good but bogs
down when loads are
connected.
1. Short circuit in a connected load.
2. Generator is overloaded.
1. Disconnect shorted electrical load.
2. See “Don’t Overload the
Generator” on page 11.
3. Contact Robin service facility.
4. Contact Generac service facility.
3. Engine speed is too slow.
4. Shorted generator circuit.
Engine will not start; or starts
and runs rough.
1. Dirty air cleaner.
2. Out of gasoline.
3. Stale gasoline.
1. Clean or replace air cleaner.
2. Fill fuel tank.
3. Drain gas tank and fill with fresh
fuel.
4. Spark plug wire not connected to
spark plug.
5. Bad spark plug.
4. Connect wire to spark plug.
5. Replace spark plug.
6. Water in gasoline.
7. Overchoking.
6. Drain gas tank; fill with fresh fuel.
7. Put choke lever to “no choke”
position.
8. Low oil level.
9. Excessively rich fuel mixture.
8. Fill crankcase to proper level.
9. Contact Robin service facility.
10. Intake valve stuck open or closed. 10. Contact Robin service facility.
11. Engine has lost compression.
11. Contact Robin service facility.
Engine shuts down during
operation.
1. Out of gasoline.
2. Low oil level.
3. Fault in engine.
1. Fill fuel tank.
2. Fill crankcase to proper level.
3. Contact Robin service facility.
Engine lacks power.
1. Load is too high.
1. See “Don’t Overload the
Generator” on page 11.
2. Replace air filter.
2. Dirty air filter.
3. Engine needs to be serviced.
3. Contact Robin service facility.
Engine “hunts” or falters.
1. Choke is opened too soon.
1. Move choke to halfway position till
engine runs smoothly.
2. Carburetor is running too rich or
too lean.
2. Contact Robin service facility.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
NOTES
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
SCHEMATIC DIAGRAM
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
WIRING DIAGRAM
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
GENERATOR EXPLODED VIEW
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
GENERATOR PARTS LIST
Item
Part #
NSP
Qty Description
Item
41
42
43
44
45
46
47
48
Part #
Qty Description
1
2
3
4
5
6
7
8
1
ENGINE, Robin 18HP
B4627
AB4682
A96925
96924
193-53621 1
194-53621 1
1
1
1
2
KEY, Ignition Switch
BB45091
A77304
BB4811
80270
78299
B4325
38353
SHIELD,
Heat
BRACKET, Ignition Switch
BRACKET, Battery Tie Down
J-BOLT, M8 - 1.25
CABLE, Battery Positive
CABLE, Battery Negative
HHCS, M5 - 0.8 x 12
2
1
1
1
1
6
SUPPORT, Engine
SHIELD, Heat
VALVE, Fuel Shut-Off
BUSHING, Fuel Valve
CAP, Fuel Tank
52618
49226
2
1
MOUNTS, Vibration
WASHER, M5 Lock
978831B
4
CAPSCREW,
M6-1.0
TANK, Fuel 10 Gal
CRADLE
GROMMET, Mounting
CAPSCREW, 3/8-16 x 3/4"
x
2
M5
Flange
Lock
10
11
12
14
15
16
17
18
B1696
1
1
4
7
AB4426
83465
23152
22237
22241
22746
22131
20 WASHER, 3/8" Lock
10 NUT, 3/8"-16 Hex
4
8
CAPSCREW, 3/8-16 x 1-3/4"
WASHER, 3/8" Flat
19BB5117
1
SHIELD,
Heat
20
21
22
23
24
25
26
27
28
B4425
195-53621 1
1
ASSEMBLY, Control Panel
WIRE ASSEMBLY, Ground
HHCS, M6 - 1.0 x 30
SWITCH, Key Ignition
WASHER, M8 Flat
WASHER, M6 Shakeproof
DECAL, 1-800
5922511
4
3/8
x
1-1/4"
60
61
62
63
64
65
66
67
68
B4803
38750
B4502
22145
26850
20566
B4986
92982
1
1
2
3
1
1
1
52618
B4794
B2153
B4988
52857
87680
23897
49813
DECAL, Ground
DECAL, Danger
29B4865
1
DECAL,
Side
Panel
30
31
32
33
34
35
36
37
38
B4866
1
1
2
1
1
1
1
1
1
DECAL, Control Panel
DECAL, Data Plate
78817
77816
B4826
B4824
79552
73054
B4268
DECAL, Caution Hot Muffler
DECAL, Start Instructions
DECAL, Start - Run - Stop
DECAL, Overlaminate
DECAL, Fuel Shut-Off
ALTERNATOR, 10KW
GUARD, Muffler
Items Not Illustrated:
BB3061
B3518
37806
43438
93568
B4472
B4888
NA
2
1
1
1
1
1
1
1
SAE 30 Oil
Oil Bottle Funnel
125 Volt 30 Amp Plug
240 Volt 30 Amp Plug
125 Volt 20 Amp Plug
Owner’s Manual
Generator Reference Card
Engine Owner’s Manual
BB4481
3920441
4
SCREW,
1/4"
x
3/4"
Self
Driller
40 B44891
BATTERY
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
ALTERNATOR EXPLODED VIEW AND PARTS LIST
Item Part #
Qty Description
Item Part #
Qty Description
1
B4906
B4907
B4908
B4909
B4910
B4911
B4912
B4913
2
1
2
1
4
1
1
1
1
SHIELD, Front
GRID, Front
BOLT, Shaft Stay
STAY BOLT, M8 x 30
ASSEMBLY, Housing
CAP
10
11
B4915
B4916
1
1
BEARING, 62052RS C3
CAPACITOR, Diode + Varistor
+ EMC
2
3
4
5
12
13
14
15
16
B4917
B4918
B4919
B4920
49820
1
1
2
8
1
ROTOR, (Includes Item 13)
FAN
SCREW, M6 - 1.0 x 10mm
SCREW, M5 - 0.8 x 10mm
LOCK NUT, M8 - 1.25
6
7
8
COVER, Blind End
COVER, Top Black
91B449
CAPACITOR,
25mF
450V
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
CONTROL PANEL EXPLODED VIEW AND PARTS LIST
Item Part #
Qty Description
Item Part #
Qty Description
1
2
3
4
5
6
7
BB4504
23897
91526
49226
75207
23365
687591
1
5
4
5
3
PANEL, Control
16
43437
1
OUTLET, 120/240V, 30 Amp
Locking
FLAT WASHER, #10 - M5
PPHMS, M5 - .08 x 12mm
LOCK WASHER, M5
17
18
0159796
20
80077
92953
1
4
1
PPHMS, M4 x 20mm
BLOCK, 50 Amp, 3 - Terminal
CIRCUIT BREAKER, 20 Amp
GROMMET,
Rubber
12 WASHER, #8 Shakeproof
OUTLET, 120V, 20
Duplex
12 FLAT WASHER, #8
84135
75477
B4894
43181
43182
77314
B4737
B95906
51716
1
1
1
4
4
1
GROMMET, Rubber
PPHMS, M5 - 0.8 x 20mm
RECTIFIER, Battery Charge
PHMS, M3 - 0.5 x 10mm
LOCK WASHER, M3
RELAY, Thermal
Amp 21
22
23
24
25
26
27
28
8
38150
922264
10 51715
12 LOCK
WASHER,
#8
12 NUT, M4 - 0.7 Hex
11
12
13
75207A
74190
68868
2
1
1
CIRCUIT BREAKER, 30 Amp
OUTLET, 120V/20A Locking
OUTLET, 120V, 30 Amp
Locking
1
1
1
ASSEMBLY, Wire Harness
BOX, Control Panel
NUT, Hex M5 - 0.8
OFF
29B3489
2
STAND
14
15
B4445
B4262
2
1
CIRCUIT BREAKER, 45 Amp
OUTLET, 120/250V, 50 Amp
30
31
B4892
51714
1
1
RESISTOR, 2ohm 25 watt
NUT, Hex M3
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
WHEEL KIT EXPLODED VIEW AND PARTS LIST
Item
1
Part #
93393B
39287
52858
93394
27007
22145
42909
39253
93693B
89635
89742
22247
87005
221292
Qty Description
1
4
5
1
1
3
1
2
1
2
2
2
2
HANDLE
2
3
4
5
6
7
8
9
10
11
12
13
14
HHCS, M8 - 1.25 x 45mm
NUT, Locking M8 - 1.25
LEG, Mounting Support
MOUNT, Vibration
FLAT WASHER, 5/16 - M8
HHCS, M8 - 1.25 x 30mm
HHCS, M8 - 1.25 x 20mm
AXLE
SPACER, Wheel
WHEEL
WASHER, Wheel
PIN, Retaining
WASHER,
M8
Lock
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products SE10000 Generator
NOTES
23
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FOR OVERHEAD VALVE V-TWIN ENGINE-DRIVEN PORTABLE GENERATORS
GENERAC PORTABLE PRODUCTS (hereafter referred to as the COMPANY) warrants to the original purchaser
that all components originally equipped with the generator, excluding the engine, for its portable generator will be
free from defects in materials or workmanship for the items and period set forth below from the date of original
purchase. This warranty is not transferable and applies only to portable generators driven by an overhead valve
V-Twin engine.
Consumer*
Commercial*
Alternator
Engine
2 years (2nd year parts only)
Warranted solely by the engine manufacturer
1 year
With the exception of European Community Countries, all units bound for export shall be warranted for
One (1) Year in Consumer applications, and 90 days in Commercial applications as defined below.
*NOTE: For the purpose of this warranty "consumer use" means personal residential household use by
original purchaser. This warranty does not apply to units used for Prime Power in place of utility.
"Commercial Use" means all other uses, including rental, construction, commercial and income
producing purposes. Once a generator has experienced commercial use, it shall thereafter be considered
a commercial use generator for the purposes of this warranty.
During said warranty period, the COMPANY will, at is option, repair or replace any part which, upon examination
by the COMPANY, is found to be defective under normal use and service**. Starting batteries are not warranted
by the COMPANY. All transportation costs under warranty, including return to the factory if necessary, are to be
borne by the purchaser and prepaid by the purchaser. This warranty does not cover normal maintenance and
service and does not apply to a generator set, alternator, or parts which have been subjected to improper or
unauthorized installation or alteration, misuse, negligence, accident, overloading, overspeeding, improper
maintenance, repair or storage so as, in the COMPANY’s judgement, to adversely affect its performance and
reliability.
**NORMAL WEAR: As with all mechanical devices, the generator needs periodic parts service and
replacement to perform well. This warranty will not cover repair when normal use has exhausted the life
of a part or generator.
THERE IS NO OTHER EXPRESS WARRANTY. THE COMPANY HEREBY DISCLAIMS ANY AND
ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT PERMITTED BY LAW. THE
DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO
THE TIME PERIOD AS SPECIFIED IN THE EXPRESS WARRANTY. LIABILITY FOR
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES
IS EXCLUDED. THE COMPANY ALSO DISCLAIMS ANY RESPONSIBILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SUCH AS THE LOSS OF TIME OR THE USE OF THE POWER
EQUIPMENT, OR ANY COMMERCIAL LOSS DUE TO THE FAILURE OF THE EQUIPMENT: AND
ANY IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other rights, which vary from state to state.
For service, see your nearest COMPANY authorized warranty service facility or call 1-877-544-0982. Warranty
service can be performed only by a COMPANY authorized service facility. This warranty will not apply to service
at any other facility. At the time of requesting warranty service, evidence of original purchase date must be
presented.
GENERAC PORTABLE PRODUCTS
Jefferson, Wisconsin 53549
Download from Www.Somanuals.com. All Manuals Search And Download.
|