®
for HDMI
EXT-
User Manual
w.gefen.com
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1
Introduction
2
Operation Notes
Features
3
4
Sender Unit Layout
Sender Unit Description
Receiver Unit Layout
5
6
7
Receiver Unit Descriptions
IR Remote Description
8
9
IR Remote Installation
10
11
12
13
14
15
16
17
18
20
21
22
25
25
26
27
28
29
30
32
33
34
IR Remote Configuration
Connecting And Operating The 4x CAT6 Extender For HDMI
Using an 4x4 Matrix
Using an 4x4 Matrix with RS-232 Control
Connection Without an 4x4 Matrix (Stand-alone Mode)
Using The Optional RMT-4IR Remote Unit
Using Stand-alone Mode
Equalizing the Signal (Matrix and Stand-alone Mode)
DIP Switch Configuration
RS-232 Serial Control Interface
Controlling the Receiver Unit with RS-232
RS-232 Serial Commands
IP Control
View Matrix Status
IP Configuration
Backup / Restore
Power Management
Network Cabel Wiring Diagram
Firmware Update
Specifications
Warranty
Licensing
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Congratulations on your purchase of the 4x CAT6 Extender for HDMI. Your
complete satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen 4x CAT6 Extender for HDMI
The Gefen 4x CAT6 Extender for HDMI sends four independent HDMI 1.3
signals, with Deep Color support, over a single CAT-6a cable to distances up to
200 feet (60 meters).
The Gefen 4x CAT6 Extender for HDMI supports HDMI 1.3 features such as
1080p Full HD and multichannel audio formats including Dolby TrueHD and DTS-
HD Master Audio.
The Gefen 4x CAT6 Extender for HDMI digital transmission method insures
100% signal integrity over this single cable extension solution.
With IR Back Channel and RS-232 support, control of the 4x4 Matrix and Hi-Def
sources, at any of the 4 individual zones, is at your fingertips. Each Receiver unit
allows control for Matrix switching and sending IR commands back to the source
located up to 200 feet (60 meters) away. The 4x CAT6 Extender for HDMI adds
IP Control to the connected Gefen 4x4 Matrix for convenient access to switching
and routing of the connected sources using a web browser.
How It Works
The Gefen 4x CAT6 Extender for HDMI can be connected in two ways :
1) Matrix Mode: As a Control and Extender system for any Gefen 4x4 Matrix unit.
Extend up to 4 of the Gefen 4x4 Matrix outputs up to 200 feet (60 meters) away
with IR, RS-232, or IP Control at any of the remote locations. Also supports the
IR Back Channel for remote control of the extended Hi-Def sources.
2) Stand-alone Mode: As a stand-alone Extender system. Connect up to 4 Hi-
Def sources to any of the available inputs. Simply extend the connected Hi-Def
sources up to 200 feet (60 meters) with IR Back Channel.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 4X CAT6 EXTENDER FOR HDMI
•
•
CAT-6a cables can be used up to 200 feet (60 meters).
Shielded (STP) CAT-6a is recommended. However, unshielded
(UTP) CAT-6a is acceptable.
NOTE: Shielded cable has an advantage by providing immunity to
Electromagnetic Interference (EMI), cell phones and A/C motors.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Supported HDMI 1.3 Features
•
•
•
•
•
225 MHz (up to 12 bit YUV 444 @ 1080p)
Deep Color
Dolby TrueHD and DTS-HD Master Audio
Lip-Sync
CEC Pass-Through
Features
•
•
Extends HDMI 1.3 at 1080p up to 200 feet (60 m)
Extends DVI at 1920x1200 up to 200 feet (60 m) when using a passive
HDMI-to-DVI adapter.
•
•
•
•
•
•
•
•
3DTV Pass-Through
Color Space Conversion
IR Remote Control
Built-in IR Extender and IR Back Channel
RS-232 serial control
IP Control (Sender unit feature)
Audio and video are transmitted digitally for zero signal loss
Supports multichannel digital audio formats including Dolby TrueHD and
DTS-HD Master Audio
•
•
•
Metal enclosure provides better RF shielding
Compensation for cable skew
Maintains settings on Power-On state
Package Includes
(1) 4x CAT6 Extender Sender Unit
(4) 4x CAT6 Extender Receiver Units
(4) 1 ft. HDMI Cables (M-M)
(1) RS-232 Serial Cable (M-F)
(1) 24V DC Power Supply
(4) 5V DC Locking Power Supplies
(1) Set of Rack Ears (Sender Unit Only)
(1) User Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SENDER PANEL LAYOUT
Front Panel
2
1
3
Back Panel
4
5
6
8
9
7
10
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SENDER PANEL DESCRIPTIONS
1
2
3
Standby Button
Sets the 4x CAT6 Extender for HDMI into Standby Mode.
IR Sensor
Receives signals from the IR Remote Control.
Power Indicator
This LED will turn bright red once the locking power supply has been properly
connected.
4
IR Blaster (4)
Used to connect the IR Blaster to the Source device.
5
CAT6 Output Jack (4)
Connects the Sender unit to the Receiver unit using CAT-6.
6
RS-232 Serial Port (Input)
The 4x4 Matrix may be switched remotely using serial communications with
any office computer or a control automation device by connecting to this port.
Please see page 20 for details.
7
8
Locking HDMI Port (4)
Connect a HI-Def source to this HDMI port.
IP Control
Connect to this port to control the 4x CAT6 Extender for HDMI using IP Control.
See page 25 for more information.
9
RS-232 Serial Port (Output)
Connects to the RS-232 control device. The 4x4 may be switched remotely
using this port. See page 20 for details.
10 24V DC Power Connector
Connects the included 24V DC power supply to this receptacle.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
RECEIVER PANEL LAYOUT
Front Panel
1
2
3
4
5
Back Panel
6
7
9
10
8
6
Download from Www.Somanuals.com. All Manuals Search And Download.
RECEIVER PANEL DESCRIPTIONS
1
Control Buttons
When connected to any 4x4 Matrix for HDMI, these remote buttons on the
Receiver unit can switch between the 4 Hi-Def inputs connected to the 4x4
Matrix for HDMI.
2
3
IR Sensor
Control the Receiver unit by pointing the IR Remote Control to the IR Sensor.
EQ Trimpot
Used to equalize the signal to compensate for distance and skew variations
found in various brands of CAT-6 cable.
4
5
Input Indicators (HDMI In 1 - HDMI In 4)
An LED will Displays the current input of the 4x4 Matrix.
Power Indicator
This LED will turn bright red once the power supply has been properly
connected.
6
IR Extender Port
Used to extend the IR Sensor range of the Receiver unit.
7
8
9
CAT6 In Connector
Connect the CAT-6 cable from the Sender unit to the RJ-45 connector.
HDMI Out
Connect the HDMI cable from the HDTV display to the HDMI Out.
RS-232 Input
Connects a controlling device to this port.
10 5V DC Locking Power Connector
Connects the included 5V DC Locking Power Supply to this receptacle.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IR REMOTE DESCRIPTION
RMT-4-IR Remote (Optional)
1
2
1
2
Activity Indicator
This LED will be activated momentarily each time a button is pressed.
Input Source Selection Buttons (1 - 4)
These buttons are used to select which input source is routed to the
HDTV display.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
RMT-4-IR REMOTE INSTALLATION
Installing the RMT-4-IR Battery
To use the RMT-4-IR Remote, remove the battery cover on the back of the
remote to reveal the battery compartment. Insert the included battery into the
open battery slot. The positive (+) side should be facing up. Ensure that both
DIP switches are set to the OFF position. Replace the battery cover and the IR
Remote is ready for action.
The IR Remote ships with 2 batteries. One battery is required for operation and
the other battery is a spare.
Battery Slot
I/R Code DIP Switches
9
Download from Www.Somanuals.com. All Manuals Search And Download.
RMT-4-IR REMOTE CONFIGURATION
Setting the IR Remote Channel on the RMT-4-IR
In the event that IR commands from other remote controls conflict with the
supplied RMT-4-IR Remote, changing the remote IR channel will fix this issue.
The RMT-4-IR Remote has a bank of DIP switches for setting the Remote IR
channel.
The DIP Switch bank on the RMT-4-IR is located underneath the battery cover.
Remote Channel 1:
Default
Remote Channel 2:
Remote Channel 4:
1
1
2
2
1
1
2
2
Remote Channel 3:
Left: Picture of the opened rear battery
compartment of the RMT-4-IR remote showing
the exposed DIP Switch bank between the
battery chambers.
The IR channel selected on the RMT-4-IR Remote must match the IR channel
assigned to the 4x CAT6 Extender for HDMI. For example, if you set both DIP
switches on the remote to the down position (IR channel 1), you must set the 4x
CAT6 Extender for HDMI to use IR channel 1.
Please refer to page 19 on how to change the IR channel on the 4x CAT6
Extender for HDMI.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE 4X CAT6 EXTENDER FOR HDMI
How to Connect the 4x CAT6 Extender for HDMI
(Matrix Mode)
1. Using any 4x4 Matrix for HDMI as a source, connect an HDMI cable from
HDMI Out 1 on the 4x4 Matrix to HDMI In 1 on the 4x CAT6 Extender for
HDMI Sender unit. To ensure correct operation of the 4x CAT6 Extender
with the 4x4 Matrix, make sure all connections are made: Connect HDMI
Out 2 on the 4x4 Matrix to HDMI In 2 on the Extender, and so on.
2. Connect the HDMI Out on the 4x CAT6 Extender Receiver unit to the display
with a user-supplied HDMI cable.
3. Using one CAT-6 cable, connect CAT6 Out 1 on the Sender unit to CAT6 In
on the Receiver unit.
4. Connect additional Receiver units as described above.
5. Connect the 5V DC locking power supplies to each Receiver unit. Do not
overtighten the locking connectors. Plug the power cord into an available
wall outlet.
6. Connect the 24V DC power supply to the 4x CAT6 Extender Sender unit and
plug the power cord into an available wall outlet.
HDMI CABLE
CAT-6 CABLE
RS-232 CABLE
IR
trix
a
4x
4x4 M
Hi-Def Sources
RS-232 Controller
er
eiv
Rec
er
ender
eiv
Rec
S
4x4 Matrix for HDMI
(not included)
er
eiv
Rec
4x
er
eiv
Rec
HD Displays
Network
IR Extenders
IR Emitter
EXT-HDMI1.3-CAT6-4X
HD Displays
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AND OPERATING THE
4X CAT6 EXTENDER FOR HDMI
How to Operate the 4x CAT6 Extender for HDMI
(using an 4x4 Matrix)
The front panel of each Receiver unit for the 4x CAT6 Extender for HDMI
contains a set of LED indicators which corresponds to an input (source) on the
4x4 Matrix device. A blue LED indicates which input has been routed from the
4x4 Matrix. On the top of each Receiver unit there are a set of 4 push-buttons
which are used to control the switching of the 4x4 Matrix.
Example 1: Routing Input (source) 3 to Output (display) 4.
1. Connect an HDMI cable from HDMI Out 4 on the 4x4 Matrix to HDMI In 4 on
the 4x CAT6 Extender for HDMI Sender unit.
2. Connect an 4x CAT6 Extender Receiver unit to Display 4.
3. Press button 3 on the top of the Receiver unit. Button 3 is shown below.
The In 3 LED will turn bright blue, indicating that Input 3 on the 4x4 Matrix
has been routed to Display 4 (Zone 4).
HDMI cable
To Display 4
CAT-6 from
Out 4 on
Button 3
Extender
In 3
Example: HDMI input 3 is routed to HDMI Out 4 (a picture of the 4x4 Matrix
display panel is shown below). The image shown on Display 4 will be the
HDMI source (3) connected to the 4x4 Matrix.
Input 3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AND OPERATING THE
4X CAT6 EXTENDER FOR HDMI
How to Connect the 4x CAT6 Extender for HDMI with RS-232 control to
the 4x4 Matrix for HDMI and to the controlled device
1. Follow steps 1 - 6 on How to Connect the 4x CAT6 Extender for HDMI (see
page 11).
2. Connect an RS-232 cable from the RS-232 serial port on the controlling
device to the RS-232 In port on the rear of the 4x CAT6 Extender for HDMI
Sender unit.
3. Connect another RS-232 serial cable from the RS-232 Out port on the rear
of the 4x CAT Extender Sender unit to the RS-232 port on the rear of the 4x4
Matrix.
NOTE: Please refer to page 20 for details on configuring RS-232 control.
Example 1: Routing Input (source) 3 to Output (display) 1 using the 4x4 Matrix.
Make sure a Receiver unit is connected to CAT6 Out 1 on the Sender unit. Use
the controlling device to send the following command:
r 1 3
The LED for In 3 will turn bright blue and the source from the 4x4 Matrix (In 3) will
be displayed on the HDTV display connected to this Receiver unit. See page 22
for details on routing using RS-232.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AND OPERATING THE
4X CAT6 EXTENDER FOR HDMI
How to Connect the 4x CAT6 Extender for HDMI
(Stand-alone Mode)
The 4x CAT6 Extender for HDMI is dependent upon an external 4x4 Matrix to
manage all the zone switching. When used as a stand-alone, without the 4x4
Matrix attached, the product functions as a one-to-one extender for each HDMI
unit. Four parallel extenders are used.
1. Connect an HDMI cable from the source device to HDMI In 1 on the back of
the Sender unit.
2. Connect the Display to the 4x CAT6 Extender Receiver unit with a user-
supplied HDMI cable.
3. Using a single CAT-6 cable, connect CAT6 Out 1 on the Sender unit to the
CAT6 In on the Receiver unit.
4. If additional Receiver units will be used, complete these connections at this
time, as described above.
5. Connect the 5V DC locking power supplies to each Receiver unit. Do not
overtighten the locking connectors. Plug the power cord into an available
wall outlet.
6. Connect the 24V DC power supply to the 4x CAT6 Extender for HDMI and
plug the power cord into an available wall outlet.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AND OPERATING THE
4X CAT6 EXTENDER FOR HDMI
Routing Sources using the Optional RMT-4-IR Remote Unit
(Matrix Mode)
There are a total of 4 buttons on the RMT-4-IR remote, which represent each of
the 4 buttons on the Receiver unit.
Example 1: Route the source connected to HDMI In 3 (from the 4x4 Matrix) on
the Sender unit to the display connected to HDMI Out 2.
Point the Remote at the Receiver unit connected to Display 2, then press button
3 on the RMT-4-IR.
Table of IR Remote Commands
for the Optional RMT-4-IR Remote Unit
RMT-4-IR Button
Source
1
2
3
4
1
2
3
4
The RMT-4-IR remote control unit will allow the selection of any input (source) on
the 4x4 Matrix unit can be will be routed to any of four Receiver units. Use the
information in the table above when routing the desired input to a display.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AND OPERATING THE
4X CAT6 EXTENDER FOR HDMI
How to Operate the 4x CAT6 Extender for HDMI
(Stand-alone Mode)
When the 4x CAT6 Extender for HDMI is used without an 4x4 Matrix, it can only
be used as an HDMI extender.
The LED on the front panel will show which HDMI is active on the Sender unit.
Example: Connect a CAT-6 cable to CAT6 Out 2 and CAT6 In, between the
Sender unit and Receiver unit.
HDMI cable
To Display
CAT6 Out 2
from Extender
In 2
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AND OPERATING THE
4X CAT6 EXTENDER FOR HDMI
How to Equalize the 4x CAT6 Extender for HDMI
(Matrix Mode / Stand-alone Mode)
The 4x CAT6 Extender for HDMI Receiver unit has an equalization trimpot to
compensate for variances that can be found in different CAT-6a cable brands. If there
is no output video or if output video contains artifacts and/or video noise, use the
steps below to adjust the EQ trimpot.
EQ trimpot
1. Insert a small flat-head screwdriver into the trimpot on the front panel of the
Receiver unit.
2. The EQ trimpot can be set to one of eight different positions. Turn the
trimpot clockwise until it clicks into the next position. Continue adjusting the
trimpot until the signal shows best results.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DIP SWITCH CONFIGURATION
DIP Switch Location
(Matrix Mode / Stand-alone Mode)
On the bottom of each Receiver unit, there are four (4) DIP switches. Each DIP
switch performs a different function.
Before modifying DIP switch settings, disconnect the power from the Receiver
unit. After the DIP switches have been configured, reconnect the power.
Receiver Unit (bottom)
DIP Switch
Bank
NOTE: By default, DIP 1 is
set to the ON position
Default settings for DIP switches
DIP Switch
Position
OFF
1
2
3
4
OFF
OFF
OFF
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DIP SWITCH CONFIGURATION
DIP Switches
(Matrix Mode / Stand-alone Mode)
DIP 1 - EDID Management
•
OFF - Local EDID
When Local EDID mode is used, the EDID will be assembled by copying
all video and audio features of the connected device. Deep Color support
will be manually controlled: If Deep Color is supported by the display(s),
DIP 2 should be set to the ON position (see DIP 2 - Deep Color, below). By
default, the unit is shipped with DIP 1 in the OFF position.
•
ON - Pass-through EDID
Allows all video and audio features of the connected devices to be passed to
the source device without control over Deep Color.
DIP 2 - Deep Color
•
OFF - Disables Deep Color support
Disables Deep Color in the EDID. Deep Color management is only available
when Local EDID is being used (DIP 1 = OFF).
•
ON - Enables Deep Color support
Enables Deep Color support. In Pass-through EDID Mode, setting DIP 2 =
ON has no effect since all EDID information is passed through.
DIP 3 / DIP 4 - IR Remote Channel
The IR channel assigned to the IR Remote Control must match the IR channel
assigned to the 4x CAT6 Extender for HDMI Receiver unit. The factory setting
(default) for DIP 3 and DIP 4 are in the OFF position.
DIP 3
OFF
ON
DIP 4
OFF
OFF
ON
IR Channel
1
2
3
4
OFF
ON
ON
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL INTERFACE
5 4 3 2 1
1 2 3 4 5
9 8 7 6
6 7 8 9
Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface
Binary Table
ASCII Corresponding RMT-4-IR Button
Binary
1
2
3
4
1
2
3
4
0011 0001
0011 0010
0011 0011
0011 0100
RS-232 Settings
Bits per second ................................................................................................. 19200
Data bits .................................................................................................................... 8
Parity .................................................................................................................. None
Stop bits .....................................................................................................................1
Flow Control ....................................................................................................... None
20
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL INTERFACE
Routing Sources using RS-232 Receiver Unit
(Matrix Mode)
1. Prepare the Receiver unit by connecting an RS-232 cable from the computer
or other controlling device to the RS-232 serial port on the back of the
Receiver unit (see page 6 - 7).
2. Configure the controller using the RS-232 settings on page 20.
CAT-6 cable
RS-232 cable
(from control
device)
HDMI cable
(to Display 4)
(from Output
4 on Sender
unit)
In 3
Example 1: Route input 3 on the 4x4 Matrix to Output 4 on the 4x CAT6 Extender
for HDMI.
Use the RS-232 controller to send the following command:
The LED for In 3 will turn bright blue and the source from Input 4 on the 4x4
Matrix will be displayed. See page 22 for details on routing using RS-232.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL COMMANDS
Functions Syntax
The syntax for each function is always the same:
#Character as the start flag → Function name → Space ( _ ) as function name
end flag → Parameter 1 → Space → Parameter n → Carriage Return ( \r )
Sample:
#FunctionName_param1_param2_param3_param4...\r
Syntax is NOT case sensitive.
Commands
Simplified syntax was used for command implementation for faster operation with
the device. The commands are not case-sensitive.
Command
Description
R
M
F
Routing command
Routes a single input to all outputs
+5V for Fiber Optic Extender Status
R Command
The R command allows specific routing of inputs and outputs when controlling
the 4x CAT6 for HDMI Sender unit.
Syntax:
r param1 param2
Parameters:
param1
param2
HDMI Ouput
HDMI Input
[1 - 4]
[1 - 4]
Notes:
When controlling the Receiver unit using RS-232, use the following syntax:
r param, where param1 is the selected input.
Example: r2 routes Input 2 on the 4x4 Matrix to the selected Receiver unit.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL COMMANDS
M Command
The M command displays the current routing status of the matrix.
Syntax:
Parameters:
None
Fiber Optic Extender Status F0 Command
The F0 command returns the state of pin 18 on the HDMI inputs.
Syntax:
f
Parameters:
None
Notes:
“High” is returned if +5V is present on HDMI input. “Low” is returned if +0V is
present on HDMI input. Setting param1 to a value of 0 will return the state of pin
18 on all HDMI inputs.
Using parameters with the F Command
Permits disabling / enabling of +5V for Fiber Optic Extenders.
Syntax:
f param1 param2
Parameters:
param1
param2
HDMI input
State
[1 - 4]
[0 - 1]
Value
Meaning
0
1
Disable
Enable
23
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL COMMANDS
General Functions
Simplified syntax was used for command implementation for faster operation with
the device: # character – isn’t needed, the command name is reduced to 1 letter.
The commands are not case-sensitive.
Function
Description
#RMTIRADD
Routing command
#LOCKPOWER Routes a single input to all outputs
#RMTIRADD Function
The #RMTIRADD function set the remote IR channel.
Syntax:
#RMTIRADD param1
Parameters:
param1
IR channel
[0 - 3]
Value
Meaning
0
1
2
3
IR channel 1
IR channel 2
IR channel 3
IR channel 4
#LOCKPOWER Function
The #LOCKPOWER enables/disables the power lock state. Enabling this feature
will store the 5V status for each input prior to shutting the unit down.
Syntax:
#LOCKPOWER param1
Parameters:
param1
State
[0 - 1]
Meaning
Value
0
1
Disable Power Lock
Enable Power Lock
24
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONTROL
The Gefen 4x CAT6 Extender for HDMI supports IP-based control using an
integrated Web interface. To access this feature, an IP address, subnet, gateway,
and port number need to be set on the 4x CAT6 Extender for HDMI (Default IP:
192.168.0.70 Subnet: 255.255.255.0 Gateway: 192.168.0.1 Port: 80). Consult
the network administrator to obtain the proper IP address and settings for this
product to properly communicate on the network.
The IP control setting can be configured via the RS-232 control interface. Once
this has been accomplished, access to the Web Interface is possible.
Simply type the IP address that was assigned to the product in a web browser to
access the Web Interface. It should look like the image below.
VIEW MATRIX STATUS
The VIEW MATRIX STATUS page will display the current status and can also be
used to create routes.
To create a new route, follow the steps below:
1. Select which outputs will display the source by clicking on each check box.
2. Select the radio button of the input that will be routed to each output.
3. Click the Switch button to update the new routing configuration.
This page will automatically refresh every minute. However, at anytime the
Refresh button can be pressed to refresh the status of the Matrix.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONTROL
IP CONFIGURATION
The IP CONFIGURATION page is used to set the IP settings that will be used to
access the Web interface. The following items can be configured from this menu.
•
•
•
•
IP Address (Default: 192.168.0.70)
Subnet (Default: 255.255.255.0)
Gateway (192.168.0.1)
Port (Default: 80)
To change these settings follow the steps below.
1. Enter the desired network information into the fields provided.
2. Press the “Save” button to initiate the change(s).
Note: After this command is complete the VIEW MATRIX STATUS page will
be displayed. Settings made on this page will not take effect until the unit is
restarted: Disconnect power from the unit and reconnect power for changes to
take effect.
At anytime, the Reset button can be pressed to return the IP settings to their
defaults.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONTROL
BACKUP / RESTORE
The Backup/Restore page is used to backup and restore complete setup
configurations.
Note: This feature will be implemented in a future release.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
IP CONTROL
POWER MANAGEMENT
The POWER MANAGEMENT page is used to set optional +5V power on an
input to power specific optional devices. The current status of this feature for
each input can be viewed on this page. To set this feature for each input follow
the steps below.
1. Select the +5V option, either “On” or “Off” for each desired input.
2. Click on the “Update” button to initiate the change(s).
Note: After this command is complete the VIEW MATRIX STATUS page will be
displayed.
This page will automatically refresh every minute, however, at anytime the
Refresh button can be pressed to refresh the status of the matrix.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
NETWORK CABLE WIRING DIAGRAM
Gefen recommends the TIA/EIA-568-B wiring option. Please adhere to the table
below when field-terminating the CAT-6 cable for use with Gefen products.
Pin
1
Color
Orange / White
Orange
2
3
Green / White
Blue
4
5
6
7
8
Blue / White
Green
Brown / White
Brown
CAT-6 cabling comes in stranded and solid core types. Gefen recommends using
solid core cabling.
It is recommended to use one continuous run from one end to the other.
Connecting through a patch is not recommended.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
FIRMWARE UPDATE
Firmware Update Procedure
To begin the update procedure, the unit’s Boot Loader must be activated. To
activate the Boot Loader, follow the procedure outlined below:
1. Connect an RS-232 cable from the computer to the RS-232 port on the
4x CAT6 Extender for HDMI.
2. Run the terminal emulation program (e.g. Windows® Hyperterminal) and
make sure the terminal settings are as follows:
a. Baud rate = 19200
b. Stop bits = 1
c. Data bits = 8
d. Flow control = None
3. Power the Sender unit.
4. Type the command: #ACTIVEBOLO\r
5. Re-type the command: #ACTIVEBOLO\r
6. Once the Boot Loader is activated, a message similar to the following should
appear in the terminal program:
4x HDMI CAT-6 Extender Boot Loading
================== Main Menu ============================
Download new program -------- 1
7. Press [1] on the computer keyboard to begin downloading the program to
temporary memory.
Waiting for the file to be sent ... (press ‘a’ to abort)
8. Under Transfer, select “Send” and upload the firmware file
(e.g. CHDMIDCAT6x4_e_x_x.bin).
9. Repeat steps 4 - 7.
10. Under Transfer, select “Send” and upload the firmware file
(e.g. SHDMIDCAT6x4_e_x_x.bin).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
FIRMWARE UPDATE
11. Connect the RS-232 cable to the Receiver unit.
12. Repeat steps 4 - 7 and upload RHDMIDCAT6x4_e_x_x.bin.
13. Repeat step 11 - 13 for each Receiver unit.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Video Amplifier Bandwidth ....................................................................... 225 MHz
Input Video Signal.....................................................................................1.2 V p-p
Input DDC Signal................................................................................5V p-p (TTL)
Maximum Video Resolution.....................................................1080p / 1920 x 1200
HDMI Connector.................................................................................Type A 19-pin
Link Connector.................................................................................RJ-45 Shielded
Power Indicator (Sender / Receiver)........................................................LED (red)
Source Indicators (Receiver)..................................................................LED (blue)
RS-232 Interface (Sender)..............................1x DB9 serial (F), 1x DB9 serial (M)
RS-232 Interface (Receiver).........................................................1x DB9 serial (M)
Power Supply...............................................24V DC (Sender), 5V DC (Receiver)
Power Consumption (Sender)..............................................................60 W (max.)
Power Consumption (Receiver)............................................................10 W (max.)
Operating Temperature .............................................................................0 - 40 °C
Sender Dimensions........................................................17.0” W x 1.75” H x 4.5” D
Receiver Dimensions.........................................................7.5” W x 1.3” H x 3.5” D
Shipping Weight...........................................................................................11.8 lbs
Certifications.............................................................UL (power supply), RoHS, CE
32
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Gefen warrants the equipment it manufactures to be free from defects in material
and workmanship.
If equipment fails because of such defects and Gefen is notified within two (2)
years from the date of shipment, Gefen will, at its option, repair or replace the
equipment, provided that the equipment has not been subjected to mechanical,
electrical, or other abuse or modifications. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
effect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or fitness for any
particular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from
Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to
be accurate. However, Gefen assumes no responsibility for any inaccuracies
that may be contained in this manual. In no event will Gefen be liable for
direct, indirect, special, incidental, or consequential damages resulting from
any defect or omission in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
specifications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return
PRODUCT REGISTRATION
Please register your product online by visiting the Register Product page
under the Support section of the Gefen Web site.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
LICENSING
lwIP is licenced under the BSD licence:
Copyright (c) 2001-2004 Swedish Institute of Computer Science.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation and/
or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Rev C3
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900 818-772-9100 fax: 818-772-9120
Pb
This product uses UL listed power supplies.
Download from Www.Somanuals.com. All Manuals Search And Download.
|