E-9232T Server
USERGUIDE
®
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
System board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Gateway Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2: Setting Up Your Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting up the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Protecting from power source problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Starting your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Turning off your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting up the operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Initial hardware settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Caring for your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning your server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Preparing for system recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
System administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Server security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using your Server Companion DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Viewing documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installing drivers and programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 4: Installing Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Preparing to install components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting a place to work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Preventing static electricity discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Accessing the internal components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Opening the server case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installing the processor air duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the bezel assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Closing the server case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installing drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Configuring your onboard RAID solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Installing memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Memory online sparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installing PCI expansion cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Replacing the processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Replacing a power supply module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Replacing a fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Replacing the CMOS battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Replacing the system board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Opening the BIOS Setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Updating the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Recovering the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Resetting BIOS passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Updating or recovering the BMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Chapter 6: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Telephone support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Telephone support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Tutoring and training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Safety guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
First steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Beep codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
LED information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Optical drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Expansion cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Appendix A: Server Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
System specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
System board specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Electronic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Additional specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Appendix B: BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Appendix C: Legal Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Back
Power connector
Cover release lever
Power supply module
Power supply voltage switch
Kensington lock slot
NIC (RJ-45) ports (2)
USB ports (4)
Serial port
Video port
Rear chassis fan
System management port
(RJ-45)
Keyboard port
Mouse port
PCI slots (shown with
EMI shields in place)
Card retention bar
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1: Checking Out Your Gateway Server
Interior
Power supply module
Cover release latch
5.25-inch drive
bays
3.5-inch drive
bays
Memory
slots
Battery
Front fan
Processor air duct
Back fan
Internal 3.5-inch
drive bays
4
Download from Www.Somanuals.com. All Manuals Search And Download.
System board
Main power connector
IPMB connector
Power connector
Memory slots
USB and NIC ports
USB and NIC ports
Diskette drive
connector
CMOS Battery
Serial port
IDE connector
SATA connectors
VGA port
Headsink and
processor
System management
port (RJ045)
Keyboard and mouse
ports)
PCIe slot 1 - PCI Express x16
PCIe slot 2 - PCI Express x4
PCI slot 3 - PCI Express x8
PCI slot 4 - Runs at 32-bits
PCI slot 5 - Runs at 32-bits
Configuration
jumpers
Getting Help
In addition to your operating system’s documentation, you can use the following information
resources to help you use your server.
Gateway Web site
Gateway provides a variety of information on its Web site to help you use your server.
Visit the Gateway Web site at support.gateway.com for:
•
•
•
•
•
Technical documentation and product guides
Technical tips and support
Updated hardware drivers
Order status
Frequently asked questions (FAQs)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1: Checking Out Your Gateway Server
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2: Setting Up Your Server
Setting up the hardware
To make sure that your working environment is safe:
•
Use a clean, dry, flat, stable surface for your server. Allow at least 6 inches at the back of
the server for cabling and air circulation.
•
Use the instructions on your server’s setup poster to set up your hardware.
Warning
Your server comes with a 3-wire AC power cords fitted with the correct plug
style for your region. If these plugs do not match the connector on your UPS or
wall outlet, do not attempt to modify the plugs in any way. Use a UPS or wall outlet
that is appropriate for the supplied AC power cords.
•
•
Use an uninterruptible power supply (UPS) with surge protection for protection from power
outages and power spikes.
Avoid subjecting your server to extreme temperature changes. Do not expose your server
to direct sunlight, heating ducts, or other heat-generating objects. Damage caused by
extreme temperatures is not covered by your warranty. As a general rule, your server is
safest at temperatures that are comfortable for you.
•
Keep your server and magnetic media away from equipment that generates magnetic
fields, such as unshielded stereo speakers. Strong magnetic fields can erase data on both
diskettes and hard drives. Even a telephone placed too close to the server may cause
interference.
Protecting from power source problems
Line conditioners, and uninterruptible power supplies can help protect your server against power
source problems.
Line conditioners
A line conditioner protects your server from the small fluctuations in voltage from an electrical
supply. Most servers can handle this variation, called line noise, without problems. However,
some electrical sources include more line noise than normal. Line noise can also be a problem
if your server is located near, or shares a circuit with, a device that causes electromagnetic
interference, such as a television or a motor.
Some uninterruptible power supplies include simple line-conditioning capabilities.
Uninterruptible power supplies
Use an uninterruptible power supply (UPS) to protect your server from data loss during a total
power failure. A UPS uses a battery to keep your server running temporarily during a power
failure and lets you save your work and shut down your server. You cannot run your server for
an extended period of time while using only the UPS. Be sure to use a UPS with surge protection.
To buy a UPS, contact Gateway Customer Care, Gateway Sales, or visit accessories.gateway.com.
Starting your server
Caution
When you connect peripheral devices to the server, make sure that your server and
devices are turned off and the power cords are unplugged.
Before you start your server for the first time:
•
Make sure that the server and monitor are plugged into a power outlet or UPS and that
the UPS (if you are using one) is turned on.
•
Make sure that all cables are connected securely to the correct ports and jacks on the back
of the server.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
To start the server:
Press the power button.
1
Power button/power
indicator LED
When the power
It means...
indicator LED is...
Blue
The server is turned on.
The server is turned off.
Low power state (S1 — S3)
Off
Slowly blinking
If nothing happens when you press the power button:
•
Make sure that the UPS, if you are using one, is connected securely to an electrical
outlet, turned on, and working correctly.
•
Make sure that the monitor is connected to the server, plugged into the power outlet
or UPS, and turned on. You may also need to adjust the monitor’s brightness and
contrast controls.
2
The first time you turn on the server, any pre-installed operating system may begin asking
you for configuration settings. See your operating system’s documentation for instructions
on configuring advanced settings for your specific network.
Selecting the boot device
To select which device your server boots from:
1
2
During server startup, press F10. The Boot menu opens.
Select the device you want to boot from. Common choices include:
•
•
•
•
Removable Dev. (Removable device)
ATAPI CDROM (CD or DVD drive)
Hard Drive
NVIDIA Boot Agent
Understanding the power-on self-test
When you turn on your server, the power-on self-test (POST) routine checks the server memory
and components. If POST finds any problems, the server displays error messages. Write down
page 58 for troubleshooting information.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2: Setting Up Your Server
Turning off your server
Every time you turn off your server, first shut down the operating system. You may lose data
if you do not follow the correct procedure.
Warning
The power button on the server does not turn off server AC power. To remove
AC power from the server, you must unplug both AC power cords from the wall outlet
or power source. The power cords are considered the disconnect device to the main (AC)
power.
To turn off the server:
1
See the operating system’s documentation or online help for instructions on shutting down
the operating system. Whenever possible, you should use the operating system’s shut
down procedure instead of pressing the power button.
2
If your server did not turn off automatically, press the power button. If nothing happens
when you press the power button, press and hold it for five seconds and the server will
turn off.
Caution
If you routinely turn off your server (daily or weekly), do not unplug the
server or use the On/Off switch on the UPS. Regularly cutting off all power to your
server may cause the CMOS battery to fail prematurely.
Setting up the operating system
If you ordered your server with the operating system already installed by Gateway, in most cases
it is completely installed and the basic settings are already configured. The Windows Small
Business Server operating system may require additional installation, depending on the version
you ordered. See your operating system’s documentation for instructions on completing the
installation or configuring advanced settings for your specific network.
If you are installing an operating system because it was not already installed by Gateway, see
the appropriate installation guide for instructions.
Initial hardware settings
Your server comes from the manufacturer with the correct initial hardware settings to operate
your server as configured. However, at some point you might want to change settings to reflect
a tasking change, a change in security requirements, or the addition of new resources to your
server.
General hardware settings, as well as the onboard RAID solution, can be changed by using the
BIOS Setup utility. Add-in RAID solutions must be configured using the specific RAID console which
accompanied that solution.
onboard RAID and the RAID BIOS Console utility, see “Configuring your onboard RAID solution”
on page 28. For information on a specific RAID console for an add-in RAID solution, see the
documentation on that hardware which accompanied your RAID solution.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3: Maintaining Your Server
Caring for your server
To extend the life of your server:
•
•
Be careful not to bump or drop your server.
When transporting your server, we recommend that you put it in the original packaging
materials.
•
•
Keep your server and magnetic media away from equipment that generates magnetic
fields.
Avoid subjecting your server to extreme temperatures. Do not expose your server to
heating ducts or other heat-generating objects. Damage caused by extreme temperatures
is not covered by your warranty. As a general rule, your server is safest at temperatures
that are comfortable for you.
•
•
Keep all liquids away from your server. When spilled onto server components, almost any
liquid can result in expensive repairs that are not covered under your warranty.
Avoid dusty or dirty work environments. Dust and dirt can clog the internal mechanisms
and can cause the server to overheat.
Cleaning your server
Keeping your server clean and the vents free from dust helps keep your server performing at
its best. Your server cleaning kit could include:
•
•
•
•
•
•
•
A soft, lint-free cloth
Glass cleaner
An aerosol can of air with a narrow, straw-like extension
Isopropyl alcohol
Cotton swabs
A tape drive cleaning cartridge (if a tape drive is installed)
A CD or DVD drive cleaning kit
Cleaning tips
Warning
When you shut down your server, the power turns off, but some electrical
current still flows through your server. To avoid possible injury from electrical
shock, unplug the power cords and all other cables connected to the server.
•
•
Always turn off your server and other peripheral devices before cleaning any components.
Use a damp, lint-free cloth to clean your server and other parts of your server system. Do
not use abrasive or solvent cleaners because they can damage the finish on components.
•
Keep the cooling vents free of dust. With your server turned off and unplugged, brush
the dust away from the vents with a damp cloth, but be careful not to drip any water into
the vents.
Cleaning the keyboard
You should clean the keyboard occasionally by using an aerosol can of air with a narrow,
straw-like extension to remove dust and lint trapped under the keys.
If you spill liquid on the keyboard, turn off your server and turn the keyboard upside down to
let the liquid drain. Let the keyboard dry completely before trying to use it again. If the keyboard
does not work after it dries, you may need to replace it. Keyboard damage resulting from spilled
liquids is not covered by your warranty.
Cleaning the screen
Caution
The flat panel display screens are made of specially coated glass and can be
scratched or damaged by abrasive or ammonia-based glass cleaners.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If your computer screen is a flat panel display, use only a damp, soft cloth to clean it. Never
spray water directly onto the screen.
- OR -
If your computer screen is not a flat panel display, use a soft cloth dampened with glass cleaner
to clean the screen. Never spray cleaner directly onto the screen.
Cleaning the tape drive
If you use a tape drive to back up your files, regular maintenance will lengthen the life of the
drive. To maintain the drive’s reliability:
•
•
Clean the drive monthly with the cleaning cartridge included with the drive.
Remove the tape from the drive whenever the drive is not in use.
Preparing for system recovery
If your system files are corrupted, you may not be able to start the server from the hard drive.
Startup diskettes or bootable media such as CDs or DVDs let you start the server and attempt
to fix the problem. See your operating system’s documentation or online help for instructions
on creating startup media.
Some operating systems also let you create an emergency repair diskette to back up critical
operating system files. See your operating system’s documentation or online help for instructions
on using an emergency repair diskette.
Recording the BIOS configuration
To help keep track of your custom changes to BIOS settings and to prepare for system recovery,
you should record your BIOS configuration after you have your server set up and working.
To record your BIOS configuration:
1
2
Restart your server, then press F2 when the Gateway logo screen appears during startup.
The BIOS Setup utility opens.
3
Record the BIOS settings on your printout.
System administration
Gateway Systems Manager
Gateway Systems Manager (GSM) lets you manage multiple computers on a Windows network
from a single window, then implement commands and policies across the network with a single
action. With Gateway Systems Manager, you can run system management tasks which are
triggered by certain events or conditions.
For more information, refer to the Gateway Baseboard Management Controller (BMC) User Guide
at support.gateway.com (by selecting this server from the list). You can also find additional
information in the program’s online help.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3: Maintaining Your Server
Server security
Using BIOS security passwords
To prevent unauthorized use of the server, you can set server startup passwords. Set an
administrator password to prevent unauthorized access to the BIOS Setup utility.
To set the BIOS security passwords:
1
Restart your server, then press F2 when the Gateway logo screen appears during startup.
The BIOS Setup utility opens.
2
3
4
5
Select the Security menu.
Select Set Supervisor Password.
Type the password and press ENTER, then type it again and press ENTER.
Save your changes and close the BIOS Setup utility.
To remove a BIOS security password:
1
Restart your server, then press F2 when the Gateway logo screen appears during startup.
The BIOS Setup utility opens.
2
3
4
Select the Security menu, then select the password to remove.
Enter the current password, then press ENTER.
For the new password, leave the password field blank, then press ENTER. The password is
removed.
Tip
Passwords can also be cleared using jumpers on the system board. For
Updating the baseboard management controller
firmware
The baseboard management controller (BMC) performs several system management functions
such as:
•
Monitoring server components (FRU) and sensor data records (SDR) (the information
provided depends on the option selected)
•
•
Managing non-volatile storage for the system event log and sensor data records
Interfacing with the emergency management port to send alerts and interact with remote
management systems
•
Fault resilient booting (the extent depends on the option selected)
You should update the BMC firmware when Gateway Customer Care has instructed you to update
it.
To update the BMC firmware:
1
2
3
Download the BMC firmware zip file from support.gateway.com.
Read the release notes for the firmware update.
Follow the instructions on the Web site or in the readme.txt file in the downloaded zip file
to update the firmware.
4
When the BMC update is complete, reboot your server.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Server Companion DVD
You can use your Server Companion DVD to:
•
•
•
Install hardware drivers
Install programs
View server documentation
Server Companion DVD contents
The Server Companion DVD is a tool you can use to help maintain your server. The DVD contains:
•
•
Computer and component documentation
Drivers and utilities for servers running Windows 2003 Server
Viewing documents
The DVD contains documents for your server and for some optional components. You can view
the documents with the Acrobat® Reader® version 4.0 and above.
To view documents:
1
Insert the Server Companion DVD into the DVD drive on a computer running the Windows
operating system. The Gateway Application and Driver Recovery window opens.
- OR -
If the window does not open, run the file Run m en u.exe on the DVD.
Click Documentation. The server document list opens.
Click the title of the document you want to view. The document opens.
To access files manually, open the Docs\Manuals folder on the Server Companion DVD.
2
3
4
To install Acrobat Reader 7:
•
Click the link for Acrobat on the Documentation page.
- OR -
Run Docs\ Read er\ ap p 21279\ Setu p.exe from the Server Companion DVD.
Installing drivers and programs
You can install drivers and programs directly onto the server by using the Server Companion
DVD. You can also extract drivers onto diskette from the DVD at any Windows workstation.
Important
The Server Companion DVD’s Gateway Application and Driver Recovery utility works
only in Windows operating systems.
To install drivers and programs at the server:
1
Insert the Server Companion DVD into your server’s DVD drive. The Gateway Application
and Driver Recovery window opens.
- OR -
If the window does not open automatically, run the file Run m en u.exe on the DVD.
A list of programs and drivers that you can install appears in the Drivers and Application
Recovery list.
2
Click the program or driver you want to install, then click Install. Follow any on-screen
instructions.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3: Maintaining Your Server
To access the files manually:
•
Open the Drivers folder on the Server Companion DVD, then open the appropriate
subfolder.
To extract drivers and programs to diskettes:
1
Insert the Server Companion DVD into your server’s DVD drive. The Gateway Application
and Driver Recovery window opens.
- OR -
If the window does not open automatically, run the file Run m en u.exe on the DVD.
Click Extract Drivers.
Click your server model and server operation system at the right of the window, then click
Search. A list of programs and drivers that you can create diskettes for appears in the
Drivers and Application Recovery list.
2
3
4
Click the program or driver you want to extract, then click Extract. Follow any on-screen
instructions.
To access the files manually:
•
Open the Drivers folder on the Server Companion DVD, then open the appropriate
subfolder.
Booting the Server Companion DVD
By booting the Server Companion DVD you can re-install the operating system, repair applications
and drivers, or exit to the command prompt.
Important
Although the Server Companion DVD is bootable, it does not include network
operating system files and is not intended to restore your operating system.
To boot to this DVD:
1
2
3
4
With your server turned on, insert the Server Companion DVD into the DVD drive.
Restart your server. A message appears asking you to select an option.
Press any key to boot from the DVD. The Gateway Options Main Menu appears.
Follow any on-screen instructions.
You can use the options in this menu to reformat your hard drive, create mass-storage
driver disks, or reload selected applications.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
Important
You must open your server case to install components. If you are not comfortable
with these procedures, get help from a more experienced computer user or computer
service technician, or contact Gateway Customer Care.
Preparing to install components
Selecting a place to work
Work on your server in an area that:
•
•
•
•
•
•
Is clean (avoid dusty areas)
Is a low-static environment (avoid carpeted areas)
Has a stable surface on which to set your server
Has enough room to place all of your server parts
Is near a grounded outlet so you can test your server after installation
Is near a telephone (in case you need help from Gateway Customer Care). The telephone
must be directly connected to a telephone jack and cannot be connected to your server.
Gathering the tools you need
Some tools and supplies that you may need to work on your server are:
•
•
•
•
•
A notebook to take notes
A Phillips screwdriver
A small flat-blade screwdriver
Small containers to store various types of screws
A grounding wrist strap (available at most electronic stores)
Preventing static electricity discharge
Warning
To avoid exposure to dangerous electrical voltages and moving parts, turn off your
server and unplug the power cords and modem cable before opening the server case.
The components inside your server are extremely sensitive to static electricity, also known as
electrostatic discharge (ESD).
Caution
ESD can permanently damage electrostatic discharge-sensitive components in the
server. Prevent ESD damage by following ESD guidelines every time you open the server
case.
Before working with server components, follow these guidelines:
•
•
Turn off the server, then unplug the power cords and all other cables.
Press the power button to drain any residual power from the server.
Warning
To prevent risk of electric shock, do not insert any object into the vent holes
of the power supply module.
•
Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare
metal part of the server. You can also touch a bare metal surface on the back of the server
with your finger.
•
•
Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam.
Avoid working on the server when your work area is extremely humid.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Remove components from their antistatic bags only when you are ready to use them. Do
not lay components on the outside of antistatic bags because only the inside of the bags
provide electrostatic protection.
Always hold expansion cards by their edges or their metal mounting brackets. Avoid
touching the edge connectors and components on the cards. Never slide expansion cards
or components over any surface.
Accessing the internal components
Opening the server case
Caution
For correct cooling and air flow, always reinstall the side panel and the air duct (if
included) before you turn on the server. Operating the server without the cover in place
can damage server components.
Because the components inside your server are extremely sensitive to static electricity, make sure
that you follow the instructions at the beginning of this chapter to avoid static electricity damage.
To open the server case:
1
2
Turn off the server, then unplug the power cords and all other cables connected to the
server.
Warning
This server may have two power cords. To disconnect internal AC power,
you must unplug both power cords.
3
4
Remove the case cover thumbscrew.
Lift the cover release lever.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
5
Swing the side panel away from the computer.
6
Lift the panel away from the server and place it out of the way.
Removing the bezel assembly
To remove the bezel assembly:
1
2
After removing the side panel, press the three black plastic tabs (positions indicated by
the arrows) to release the right side of the bezel.
3
Swing the right side of the bezel out until the left side of the bezel can be disengaged
from the left side of the computer, then remove the bezel.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the processor air duct
To remove the processor air duct:
1
2
3
Remove the cables from the air duct cable clip.
4
Grasp the air duct handle and remove the processor air duct from the chassis.
Air duct
Processor air duct
handle
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
Installing the processor air duct
Important
Be careful not to snag or unplug the fan cable when you install the processor air duct.
To install the processor air duct:
1
Align the left side of the processor air duct with the front fan and insert the installation
tabs on the bottom of the air duct into the installation holes in the side of the chassis.
Processor air duct
installation tabs
Processor air duct
installation holes
2
3
Press the processor air duct into place.
Place the diskette cable and hard drive power cable behind the cable clip on the processor
air duct.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the bezel assembly
Important
If you have installed any new drives in the external drive bays, make sure to remove
the corresponding filler panels in the bezel before installing it.
To install the bezel assembly:
1
Insert the tabs on the left side of the bezel into the slots in the left side of the computer.
2
3
Swing the right side of the bezel in to insert the tabs on the right side of the bezel into
the slots on the right side of the computer.
Press the right side of the bezel firmly until it snaps into place.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
Closing the server case
To close the server case:
1
Make sure that all of the internal cables are arranged inside the case so they will not be
pinched when you close the case.
2
Align the panel tabs into the bottom case notches, then swing the side panel toward the
top of the computer to secure it into place.
3
4
Replace the case cover thumbscrew.
Reconnect the power cords and all other cables.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing drives
Your server’s basic configuration includes one CD or DVD drive and one 3.5-inch diskette drive.
Your server also has an additional 5.25-inch drive bay and 3.5-inch drive bay.
Your server can have as many as four SATA (standard) or SCSI (optional) drives in three internal
drive bays and one external fixed drive bay (the bottom 3.5-inch bay).
CD or DVD drive
5.25-inch drive bay
3.5-inch floppy drive
3.5-inch external drive bay
As you prepare to install drives, remember:
•
Do not use the top 5.25-inch drive bay for drives which have electronic components
exposed on the top. Drive mounting rails at the top of the bay may damage any exposed
electronic components.
•
•
Before you install a drive, see the drive’s documentation for information on configuring
the drive, setting drive jumpers, and attaching cables.
IDE drives can be configured as master, slave, or cable-select.
•
If cable-select is available (drive assignments will be marked on the cable), the IDE cable
assigns the master/slave positions to the drives it connects. You can override these
assignments using the jumpers on the drives.
•
If cable-select is not available and only one drive is attached to an IDE controller cable,
configure the drive as master if it is a CD or DVD drive. If two drives of any type are
attached to the cable, configure one as master and one as slave.
•
You may need to configure the drives you install using the BIOS Setup utility. Press F2 at
startup to open the BIOS Setup utility.
Installing or replacing a fixed or removable-media drive
Use these instructions to install or replace a diskette, CD, DVD, hard drive, or tape drive.
To install a drive in an external drive bay:
1
2
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
3
4
If you are adding a new drive to an available drive bay, remove the EMI shield from the
bay by pulling the shield out of the bay.
EMI shield
5
6
7
Disconnect the old drive’s cables from the back of the drive.
Slide the green drive retainer lever toward the back of the drive bay, then pull the drive
out of the bay.
Drive retainer lever
8
9
Set any jumpers on the new drive. See the drive’s documentation for further instructions.
Important
If you are installing a hard drive in the bottom, external 3.5-inch drive bay,
the green drive retainer lever will not slide forward to lock the drive into place.
Instead, you must use a screw to secure the drive in the bay.
Slide the new drive into the drive bay allowing it to protrude enough to line up with the
bezel when it is replaced, then push the green drive retainer lever toward the front of the
drive bay to lock the drive into place.
Tip
When installing a CD, DVD, tape drive, or diskette drive, if the green drive
retainer lever will not slide forward all the way to lock the drive into place, move
the drive slightly, until the lever can be moved forward enough to lock the drive
into place.
10 Connect the power and data cables.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing or replacing a hard drive
Important
To install a hard drive in the bottom external 3.5-inch drive bay, follow the
Use these instructions to install or replace a hard drive.
To install a hard drive in an internal drive bay:
1
2
3
- OR -
If you are adding a new drive to an available drive bay, slide the green drive retainer lever
4
5
Disconnect the old drive’s cables from the front of the drive.
Slide the green drive retainer lever toward the front of the drive bay, then pull the drive
out of the bay.
Drive retainer lever
6
7
Set any jumpers on the new drive. See the drive’s documentation for further instructions.
Slide the new drive into the drive bay as far as it will go, then slide the green drive retainer
lever toward the back of the drive bay to lock the drive into the bay.
Tip
If the green drive retainer lever will not slide back all the way to lock the
drive into place, move the drive slightly, until the lever can be moved back enough
to lock the drive into place.
8
9
Connect the power and data cables.
10 Format and partition the drive as necessary.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
Configuring your onboard RAID solution
Your server comes equipped with an onboard chipset for a SATA RAID solution, which supports
RAID levels 0 (striping), 1 (mirroring), 5 (distributed data and parity), and 10 (RAID 0 + 1). You
by launching the appropriate RAID BIOS console during the boot process.
Configuring the onboard SATA RAID solution
Level
Description and use
Pros
Cons
Number of
drives
Fault
Tolerant
0
Data divided into blocks and
distributed sequentially (pure
striping). Use for non-critical data
that requires high performance.
High data
throughput for
large files.
No fault tolerance.
Data is lost if a drive
fails.
One or two
(on this
server)
No
1
Data duplicated on another disk
(mirroring). Use for read-intensive,
fault-tolerant systems.
100 percent
data
redundancy,
providing fault
tolerance.
More disk space
required. Reduces
usable disk space to
the size of the
smallest drive.
Reduced
Two
Yes
performance during
rebuilds.
5
Stripes data at a block level across
several drives and distributes parity
among the drives. No single disk is
devoted to parity.
Fast and
More disk space
Three
Four
Yes
Yes
redundant
required. Reduces
usable disk space to
75% of total storage
in the disk array.
10
A combination of RAID 1 and RAID
0. Raid 0 is used for performance,
and RAID 1 is used for fault
tolerance.
Fast and
redundant
An additional drive
required.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
To launch the SATA RAID BIOS console:
1
2
Restart your server.
Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
3
From the Main BIOS menu, select the Advanced menu.
4
Select the Integrated Devices sub-menu. The Integrated Devices sub-menu opens.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
5
Select the NV RAID Configuration sub-menu. The NV RAID Configuration sub-menu opens.
6
7
8
9
For the NV RAID Configuration option, click Enabled.
Select the SATA channels your hard drives are connected to and set them to Enabled.
Exit the BIOS Setup utility.
Restart your server. During the boot process you will see the following message:
10 Press F10. The RAID BIOS console opens.
11 Configure the RAID options, then exit the RAID BIOS console.
12 Reboot the server.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
To configure the SATA RAID solution:
1
Open the RAID BIOS console as described in the previous procedure. The Define a New
Array screen opens.
2
Select a RAID Mode from the list at the top left of the screen.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
3
Select a Stripping Block size from the list at the top right of the screen.
4
Highlight the free disk you want to use from the list on the left side of the screen.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press the right arrow key to move the disk to the Array Disks list on the right side of the
screen. Do this for all disks you want to use in the array.
6
Press F7 to finish creating the array. When the confirmation box opens, press Y to clear
the data on the disks.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
The Array List opens showing the disks in the array.
7
8
To make the array bootable, press B (Set Boot) to change Boot No to Boot Yes.
Exit the RAID Configuration utility and reboot the server.
Installing memory
Caution
Use only 667 Mhz compliant, 240-pin, SDRAM unbuffered ECC DIMM memory
modules.
The system board supports 4 DDR2 667 MHz vertical DIMMs to provide up to 8 GB of memory
with ECC support. The 667 MHz differential memory clocks are driven by the AMD processor with
length matching and impedance controlled through all the DIMM slots. Supported DIMM sizes
include 256 MB, 512 MB, 1 GB, and 2 GB.
The BIOS configures the memory controller to run in either single channel or dual channel mode,
depending on the following:
•
•
If one or more fully populated DIMM banks are detected, the memory controller will run
in dual channel mode.
If only a single DIMM is present, the memory controller will run in single channel mode.
DIMM banks must be populated using the following guidelines:
•
•
DIMM banks must be populated in order, starting with Bank 0.
Dual rank DIMMs must be populated before single rank DIMMs.
Channel B DIMM 2
Channel A DIMM 2
Channel B DIMM 1
Channel A DIMM 1
34
Download from Www.Somanuals.com. All Manuals Search And Download.
To install or replace memory:
1
2
3
Pull the plastic tabs (1) away from the sides of the memory module slot. If you are replacing
a memory module, lift the old memory module (2) out of the slot.
4
Align the notch on the new module with the notch in the memory module slot and press
the module firmly into the slot. The tabs on the sides of the memory slot should secure
the memory module automatically.
5
6
Restart your server and open the BIOS Setup utility. Verify the System Memory listed in
the Main menu. When you exit the BIOS Setup utility, make sure that the operating system
loads completely.
Memory online sparing
The chipset on the system board in the server supports memory online sparing, which can provide
a way to prevent data loss in case of DIMM failure. If a DIMM failure does occur, a DIMM fault
LED adjacent to the DIMM slot will light orange to indicate the failed memory module.
Using memory online sparing, one DIMM per channel (selectable in the BIOS setup utility) is used
as a memory spare (the spare DIMM must be equal to, or larger than, the largest DIMM in that
channel). If a DIMM begins to fail, the contents of the failing DIMM is copied to the spare DIMM
in that channel. When all of the data is copied, the primary DIMM is automatically removed from
service. Since one DIMM per channel is always maintained as a spare, a maximum of only 75%
of the installed memory is usable. Memory online sparing is configured in the BIOS.
Installing PCI expansion cards
Caution
This server does not have PCI hot-plug capability. Do not attempt to install or remove
a PCI card without turning off your server and disconnecting it from the AC power source.
Use the following chart to determine the PCI slot into which you should install your expansion
card.
PCI slot
Description
1
2
3
4
5
PCI Express - x16
PCI Express - x4
PCI Express - x8
PCI - Runs at 32-bits
PCI - Runs at 32-bits
35
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
PCI slot 1
PCI slot 2
PCI slot 3
PCI slot 4
PCI slot 5
To replace, add, or reseat a PCI expansion card:
1
2
3
4
If you are replacing a card, disconnect any cables that are attached to the old card.
Loosen the captive thumbscrew on the card retention bar and swing the bar out from the
back of the chassis.
Card retention bar
Captive thumbscrew
5
If you are replacing a card, remove the old expansion card. To loosen the card you can
slightly rock the card end-to-end, but do not bend the card sideways.
Caution
Do not touch the contacts on the bottom part of the expansion card.
Touching the contacts can cause electrostatic damage to the card.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press the new card into the expansion slot. To help insert the card you can slightly rock
the card end-to-end, but do not bend the card sideways.
7
Swing the card retention bar back into place and tighten the captive thumbscrew.
Card retention bar.
Captive thumbscrew
37
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
8
9
Connect any cables to the card. For more information, see the instructions in the card’s
documentation.
10 See the card’s documentation for software installation instructions.
Replacing the processor
Warning
The processors and heatsink may be hot if the computer has been running. Also,
there may be sharp edges on the heatsink. Consider wearing protective gloves.
The system board has a single AM2 CPU socket which supports one AMD® Opteron™ or Athlon™
processor with 3.0 GHz Hyper Transport Bus. The system connects with the nVIDIA MCP 55
through the Hyper Transport Bus. The server automatically detects the processor each time you
turn it on. Whenever you install a new processor, you should first install the most current version
Caution
A heatsink must be installed on the processor. Installing a processor without a
heatsink could damage the processor.
To replace a processor:
1
2
that you turn off the server, then unplug the power cord(s) and all other cables connected
to the server.
3
4
Loosen the four screws holding the heatsink to the processor, then lift the heatsink off
the processor.
Screw
Screw
Screw
Screw
Caution
The heatsink has Thermal Interface Material (TIM) on the bottom. Be careful
not to damage this material when you remove the heat sink from the processor.
If removing the heatsink also pulls the processor out of the processor socket, the
processor could be damaged.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Unlock the retention lever and lift it up to release the processor.
6
Lift the processor out of the socket and place it in a static-free bag or case for storage.
7
Insert the new processor into the socket, making sure that the gold triangle on the corner
is situated as shown in the following illustration.
Caution
The processor only fits the socket when oriented as indicated. Do not force
the processor into the socket to avoid bending the pins or damaging the processor.
If the processor does not fit completely, check its orientation and check for bent
pins.
Gold triangle
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
8
9
When the processor is oriented correctly and in place, press it firmly into the socket, rotate
the retention lever into place until it clicks.
Caution
The heatsink has Thermal Interface Material (TIM) located on the bottom of
it. Use caution when you unpack the heat sink so you do not damage the TIM. If
you are reusing the original heatsink, make sure that the TIM on the bottom of
the heatsink is not damaged. If the TIM is damaged, you should remove the old
TIM, then apply new TIM to the bottom of the heatsink.
Place the heatsink down onto the processor, then gently tighten the heatsink retaining
screws to secure it into place.
Replacing a power supply module
Warning
The power supply modules in this server contain no user-serviceable parts. Only a
qualified computer technician should service the power supply modules.
Your server comes with 3-wire AC power cords fitted with the correct plug style for your
region. If this plug does not match the connector on your surge protector, UPS, or wall
outlet, do not attempt to modify the plug in any way. Use a UPS or wall outlet that is
appropriate for the supplied AC power cords.
If your server uses the optional hot-swappable, redundant power supplies and one of the two
power supplies fails, the other power supply module supports the server while you replace the
failed module. You do not need to turn off the server or disconnect peripheral devices to replace
a failed power supply module.
To replace a power supply module:
1
2
If you only have one power supply module, turn off your server.
If you have two power supply modules, examine the LED indicators on the back of each
power supply module to identify the failed module. The power supply module has failed
if the orange (right) LED indicator is on.
Power supply handle
Power supply fault LED
Power connector
Power supply latch
Power on LED
3
Unplug the power cord from the failed power supply module.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
4
While pressing the green latch on the power supply module, grasp the handle and pull
the module straight out from the server.
5
6
Slide the new power supply module into the empty power supply bay until the green latch
snaps into place.
Plug the power cord into the new power supply module.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
Replacing a fan
Important
Make sure that you replace a fan with an identical replacement fan.
To replace a front fan:
1
2
3
Remove the processor air duct by following the instructions in “Removing the processor
4
Unplug the fan cable from the fan connector on the system board.
Fan retention tab
Fan release tab
Fan handle
Fan retention tab
Fan cable
5
Grasp the fan handle and press the fan release tab, then disengage the fan and move it
away from the chassis.
6
7
Pull the fan from the chassis.
Insert the new fan into the opening left by the old fan, then insert the fan retention tabs
and fan release tab into the chassis until it snaps into place.
8
9
Plug the fan cable into the fan connector on the system board.
Replace the processor air duct by following the instructions in “Installing the processor air
42
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace a back fan:
1
2
3
Unplug the fan cable from the fan connector on the system board.
Fan cable
Fan retention screw
Fan retention screw
4
5
Unscrew the four fan retention screws holding the fan to the back of the chassis.
Pull the fan from the chassis, noting the orientation.
Important
Make sure that the new fan is oriented the same way (air flow) as the old fan.
6
7
8
Insert the new fan into the chassis, then replace the fan retention screws.
Plug the fan cable into the fan connector on the system board.
Replacing the CMOS battery
Warning
There is a danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type of battery recommended by the manufacturer. Dispose of used
batteries following the manufacturer’s instructions.
If the server clock does not keep time or the settings in the BIOS Setup utility are not saved when
you turn off the server, replace the CMOS battery with an equivalent battery.
To replace the battery:
1
2
43
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
3
4
Record the BIOS settings on your printout, then close the utility.
Turn off your server, then follow the instructions in “Preventing static electricity discharge”
5
6
Locate the old battery on the system board and note its orientation (see “System board”
on page 5 for the general location of the battery). You will need to install the new battery
the same way.
Battery retention clip
7
8
9
Push the battery retention clip away from the battery until the battery pops up.
Remove the old battery.
Make sure that the positive (+) side of the new battery is facing correctly, then press the
new battery into the socket until it snaps into place.
11 Turn on the server.
12 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
14 Save all your settings and close the BIOS Setup utility.
Replacing the system board
To replace the system board:
1
2
3
Remove the processor air duct by following the instructions in “Removing the processor
4
5
6
7
Remove the memory modules by following the instructions in “Installing memory” on
Remove all of the expansion cards by following the instructions in “Installing PCI expansion
Remove the heat sink and processor by following the instructions in “Replacing the
Disconnect the power and data cables from the system board, noting their locations and
orientation. (You will reconnect the cables after you install the new board.)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Remove the seven screws securing the system board to the case.
Screw
Screw
Screw
Screw
Screw
Screw
Screw
9
Pull the system board away from the case and carefully remove it, then place it in a
static-free bag on a stable work surface.
10 Insert the new system board into the case, aligning the holes in the board with the threaded
standoffs on the side of the case.
11 Secure the system board to the case with the seven (7) screws you removed previously.
14 Connect the power and data cables.
17 Turn on your server.
18 Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
19 Check BIOS settings to make sure that they detect the server’s new hardware, then save
your changes (if any) and close the BIOS Setup utility.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4: Installing Components
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Opening the BIOS Setup utility
The BIOS Setup utility stores basic settings for your server. These settings include basic hardware
configuration, resource settings, and password security. These settings are stored and saved even
when the power is off.
Caution
The options in the BIOS Setup utility have been set at the factory for optimal
performance. Changes to these settings will affect the performance of your server.
Before changing any settings, write them down in case you need to restore them later.
You can record the settings on a printout of this guide’s appendix for “BIOS Settings” on
To open the BIOS Setup utility:
1
Restart your server, then press F2 when the Gateway logo screen appears during startup.
The BIOS Setup utility opens.
When you select menu items, the Item Specific Help box on the right side of the screen
displays specific information about the selection. The command bar across the bottom of
the screen shows the keys you press to access help, navigate through the menus, and
perform other tasks.
2
Select one of these menus:
•
•
•
•
•
•
Main gives you access to basic information and settings related to your server’s
hardware and configuration.
Advanced gives you access to information and settings for PCI, peripheral devices,
memory, and the chipset.
Boot gives you access to information and settings for startup features and startup
sequences.
Security gives you access to settings related to system access passwords. For more
Server gives you access to settings for system management, console redirection, event
log configuration, and fault-resilient boot settings.
Exit gives you access to options for closing the BIOS Setup utility.
Updating the BIOS
To update the BIOS:
1
2
3
4
5
Restart your server, then press F2 when the Gateway logo screen appears during startup.
Record any custom BIOS settings on your printout.
Download the BIOS update files from support.gateway.com.
Follow the instructions on the Web site or the readme.txt file in the downloaded zip file
to update the BIOS.
6
7
After you have updated the BIOS, restart your server and load the default BIOS values.
the BIOS Setup utility.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Recovering the BIOS
If you encounter a problem while you are updating the BIOS, such as a power outage, the BIOS
update may not be successful. If the system continues to try to boot from the new, corrupted
BIOS, you can manually recover the old BIOS so you can try another update.
Important
This method does not work if the keyboard is connected through the KVM switch.
To create a recovery disk:
1
Download 646MS100.WPH (the system BIOS for your server) from the Gateway Support
Web page, then rename the file to BIOS.WPH.
2
Download CRISDISK.ZIP (a Crash Recovery Diskette utility) from the Gateway Support Web
page, then uncompress it to a folder.
3
4
5
Copy BIOS.WPH (the file you renamed) to the same folder.
Insert a blank, formatted floppy disk into your diskette drive.
Run CRISDISK.BAT to create the recovery disk.
To recover the BIOS:
1
that you turn off the server, then unplug the power cord(s) and all other cables connected
to the server.
2
Caution
Moving the jumper while the power is on can damage your server. Always
turn off the server and unplug the power cords and all other cables before changing
the jumper.
3
Remove the jumper across pins 1-2 of header J5 and place the jumper across pins 2-3 (as
shown in the illustration).
4
5
6
Insert the recovery disk into the diskette drive.
Turn on your server and wait until you hear “beep-beep-beep,” then turn off your server
again.
7
8
9
Place the jumper back onto pins 1-2.
10 Reboot the server and verify that the recovery was successful.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5: Using the BIOS Setup Utility
Resetting BIOS passwords
To reset BIOS passwords, you must either reset and clear all BIOS settings, or use the Clear
Password jumper. To reset all BIOS settings, follow the instructions in “Resetting BIOS passwords”
To clear the BIOS password(s):
1
that you turn off the server, then unplug the power cord(s) and all other cables connected
to the server.
Caution
Moving the jumper while the power is on can damage your server. Always
turn off the server and unplug the power cords and all other cables before changing
the jumper.
2
3
Remove the jumper across pins 1-2 of header J54-A, then place the jumper across pins 2-3.
J54A (reset) jumper
4
5
6
Reconnect the power cords and turn on the server. The BIOS password(s) is cleared.
Turn off the server, then disconnect the power cords and all other cables connected to
the server.
7
8
9
Place the jumper back onto pins 1-2.
Updating or recovering the BMC
Updating or recovering the BMC firmware
To update or recover the BMC firmware:
1
2
3
Download the BMC firmware zip file from support.gateway.com.
Read the release notes for the firmware update.
Follow the instructions on the Web site or in the readme.txt file in the downloaded zip file
to update the firmware.
4
When the BMC update is complete, reboot your server.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6: Troubleshooting
Telephone support
Before calling Gateway Customer Care
If you have a technical problem with your server, follow these recommendations before
contacting Gateway Customer Care:
•
•
•
Make sure that your server is connected correctly to a grounded AC outlet that is supplying
power.
If a peripheral device, such as a keyboard or mouse, does not appear to work, make sure
that all cables are plugged in securely and plugged into the correct port or jack.
If you have recently installed hardware or software, make sure that you have installed it
following the instructions provided with it. If you did not purchase the hardware or
software from Gateway, see the manufacturer’s documentation and technical support
resources.
•
If you have “how to” questions about using a program, see:
•
•
•
•
The program’s online Help
The program’s documentation
Your operating system’s documentation
The software or hardware manufacturer’s Web site
•
•
Have your client ID, serial number (usually located on the back of your server case), and
order number available, along with a detailed description of your issue, including the exact
text of any error messages, and the steps you have taken.
•
•
Make sure that your server is nearby at the time of your call. The technician may have
you follow appropriate troubleshooting steps.
Consider using Gateway’s online technical support. Gateway’s Web site has FAQs, tips, and
other technical help. You can also use the Web site to e-mail Customer Care. For more
information, visit Gateway’s Customer Care Web site at support.gateway.com.
Telephone support
Gateway offers a wide range of customer service, technical support, and information services.
Telephone numbers
You can access the following services through your telephone to get answers to your questions:
Resource
Service description
How to reach
Gateway’s
fee-based software
tutorial service
Get tutorial assistance for software issues.
800-229-1103 (charged to your
credit card)
Gateway Customer
Care
Talk to a Gateway Customer Care representative
about a non-tutorial technical support question.
877-485-1464 (US) (say the word
“Server”) 800-846-3609 (Canada
and Puerto Rico)
605-232-2191
(all other countries)
Sales, accounting,
and warranty
Get information about available systems, pricing,
orders, billing statements, warranty service, or
other non-technical issues.
800-846-2000 (US)
888-888-2037 (Canada)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Tutoring and training
Gateway's Customer Care professionals cannot provide hardware and software training. Instead,
Gateway recommends the following training resources.
Resource
Service description
For more information
Gateway Learning
Libraries
A variety of courses and tutorials are available on
CD. Select from several easy-to-use learning
libraries.
Safety guidelines
While troubleshooting your server, follow these safety guidelines:
•
Never remove the top panel while your server is turned on and while the modem cable
and the power cords are connected.
•
Do not attempt to open the monitor. To do so is extremely dangerous. Even if the power
is disconnected, energy stored in the monitor components can be dangerous. Also, opening
the monitor voids its warranty.
•
•
Make sure that you are grounded correctly before opening the server. For more information
about preventing damage from static electricity, see “Preventing static electricity
After you complete any maintenance task where you have to open the server case, make
sure that you close the case and reconnect all cables before you restart your server.
Warning
To avoid bodily injury, do not attempt to troubleshoot your server problem if:
- The power cords or plugs are damaged
- Liquid has been spilled into your server
- Your server was dropped
- The case was damaged
Instead, unplug your server and contact a qualified computer technician.
Error messages
These messages often indicate procedural errors such as typing an incorrect keystroke or trying
to save a file to a write-protected diskette. Some messages, however, may indicate a problem
that requires further troubleshooting.
Memory messages
Gate20 Error
The BIOS is unable to correctly control the system board’s Gate A20 function, which controls
access of memory over 1 MB. This may indicate a problem with the system board.
Boot messages
Boot Failure ...
This is a generic message indicating the BIOS could not boot from a particular device. This
message is usually followed by other information concerning the device.
Invalid Boot Diskette
A diskette was found in the drive, but it is not configured as a bootable diskette.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6: Troubleshooting
Drive Not Ready
The BIOS was unable to access the drive because it indicated it was not ready for data transfer.
This is often reported by drives when no media is present.
A: Drive Error
The BIOS attempted to configure the A: drive during POST, but was unable to correctly configure
the device. This may be due to a bad cable or faulty diskette drive.
Insert BOOT diskette in A:
The BIOS attempted to boot from the A: drive, but could not find a correct boot diskette.
Reboot and Select proper Boot device or Insert Boot Media in selected Boot device
BIOS could not find a bootable device in the system and/or removable media drive does not
contain media.
NO ROM BASIC
This message occurs on some systems when no bootable device can be detected.
Storage Device messages
Primary Master Hard Disk Error
The IDE/ATAPI device configured as Primary Master could not be correctly initialized by the BIOS.
This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Primary Slave Hard Disk Error
The IDE/ATAPI device configured as Primary Slave could not be correctly initialized by the BIOS.
This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Secondary Master Hard Disk Error
The IDE/ATAPI device configured as Secondary Master could not be correctly initialized by the
BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Secondary Slave Hard Disk Error
The IDE/ATAPI device configured as Secondary Slave could not be correctly initialized by the BIOS.
This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI
devices in POST.
Primary Master Drive - ATAPI Incompatible
The IDE/ATAPI device configured as Primary Master failed an ATAPI compatibility test. This
message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices
in POST.
Primary Slave Drive - ATAPI Incompatible
The IDE/ATAPI device configured as Primary Slave failed an ATAPI compatibility test. This message
is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST.
Secondary Master Drive - ATAPI Incompatible
The IDE/ATAPI device configured as Secondary Master failed an ATAPI compatibility test. This
message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices
in POST.
Secondary Slave Drive - ATAPI Incompatible
The IDE/ATAPI device configured as Secondary Slave failed an ATAPI compatibility test. This
message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices
in POST.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
S.M.A.R.T. Capable but Command Failed
The BIOS tried to send a S.M.A.R.T. message to a hard disk, but the command transaction failed.
This message can be reported by an ATAPI device using the S.M.A.R.T. error reporting standard.
S.M.A.R.T. failure messages may indicate the need to replace the hard disk.
S.M.A.R.T. Command Failed
The BIOS tried to send a S.M.A.R.T. message to a hard disk, but the command transaction failed.
This message can be reported by an ATAPI device using the S.M.A.R.T. error reporting standard.
S.M.A.R.T. failure messages may indicate the need to replace the hard disk.
S.M.A.R.T. Status BAD, Backup and Replace
A S.M.A.R.T. capable hard disk sends this message when it detects an imminent failure.
This message can be reported by an ATAPI device using the S.M.A.R.T. error reporting standard.
S.M.A.R.T. failure messages may indicate the need to replace the hard disk.
S.M.A.R.T. Capable and Status BAD
A S.M.A.R.T. capable hard disk sends this message when it detects an imminent failure.
This message can be reported by an ATAPI device using the S.M.A.R.T. error reporting standard.
S.M.A.R.T. failure messages may indicate the need to replace the hard disk.
System configuration messages
DMA-2 Error
Error initializing secondary DMA controller. This is a fatal error, often indication a problem with
system hardware.
DMA Controller Error
POST error while trying to initialize the DMA controller. This is a fatal error, often indication a
problem with system hardware.
Checking NVRAM..Update Failed
BIOS could not write to the NVRAM block. This message appears when the FLASH part is
write-protected or if there is no FLASH part (System uses a PROM or EPROM).
Microcode Error
BIOS could not find or load the CPU Microcode Update to the CPU. This message only applies to
INTEL CPUs. The message is most likely to appear when a brand new CPU is installed in a system
board with an outdated BIOS. In this case, the BIOS must be updated to include the Microcode
Update for the new CPU.
NVRAM Checksum Bad, NVRAM Cleared
There was an error in while validating the NVRAM data. This causes POST to clear the NVRAM data.
Resource Conflict
More than one system device is trying to use the same non-shareable resources (Memory or I/O).
NVRAM Ignored
The NVRAM data used to store Plug’n’Play (PnP) data was not used for system configuration in
POST.
NVRAM Bad
The NVRAM data used to store Plug’n’Play (PnP) data was not used for system configuration in
POST due to a data error.
Static Resource Conflict
Two or more Static Devices are trying to use the same resource space (usually Memory or I/O).
55
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6: Troubleshooting
PCI I/O conflict
A PCI adapter generated an I/O resource conflict when configured by BIOS POST.
PCI ROM conflict
A PCI adapter generated an I/O resource conflict when configured by BIOS POST.
PCI IRQ conflict
A PCI adapter generated an I/O resource conflict when configured by BIOS POST.
PCI IRQ routing table error
BIOS POST (DIM code) found a PCI device in the system but was unable to figure out how to
route an IRQ to the device. Usually this error is causing by an incomplete description of the PCI
Interrupt Routing of the system.
Timer Error
Indicates an error while programming the count register of channel 2 of the 8254 timer. This
may indicate a problem with system hardware.
Interrupt Controller-1 error
BIOS POST could not initialize the Master Interrupt Controller. This may indicate a problem with
system hardware.
Interrupt Controller-2 error
BIOS POST could not initialize the Slave Interrupt Controller. This may indicate a problem with
system hardware.
CMOS messages
CMOS Date/Time Not Set
The CMOS Date and/or Time are invalid. This error can be resolved by readjusting the system
time in AMIBIOS Setup.
CMOS Battery Low
CMOS Battery is low. This message usually indicates that the CMOS battery needs to be replaced.
It could also appear when the user intentionally discharges the CMOS battery.
CMOS Settings Wrong
CMOS settings are invalid. This error can be resolved by using AMIBIOS Setup.
CMOS Checksum Bad
CMOS contents failed the Checksum check. Indicates that the CMOS data has been changed by
a program other than the BIOS or that the CMOS is not retaining its data due to malfunction.
This error can typically be resolved by using AMIBIOS Setup.
Miscellaneous messages
Keyboard Error
Keyboard is not present or the hardware is not responding when the keyboard controller is
initialized.
Keyboard/Interface Error
Keyboard Controller failure. This may indicate a problem with system hardware.
System Halted
The system has been halted. A reset or power cycle is required to reboot the machine. This
message appears after a fatal error has been detected.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
First steps
Warning
To avoid bodily injury, do not attempt to troubleshoot your server problem if:
- The power cords or plugs are damaged
- Liquid has been spilled into your server
- Your server was dropped
- The case was damaged
Instead, unplug your server and contact a qualified computer technician.
Try these steps first before going to the following sections:
•
•
•
Make sure that the power cords are connected to your server and an AC outlet and that
the AC outlet is supplying power.
If you use a surge protector or a UPS, make sure that it is turned on and is rated to handle
the power required by your server.
If you added or removed server components before the problem started, review the
installation procedures you performed and make sure that you followed each instruction.
You may need to remove the device, uninstall the device’s software, then reinstall the
device.
•
•
•
•
If an error message appears on the screen, write down the exact message before calling
Restart your server, then open the BIOS Setup utility by pressing and holding F2 while your
server restarts. Check your configuration settings.
When diagnosing problems, press the non-maskable interrupt (NMI) button to put the
If an error occurs in a program, see its documentation or online help.
Battery replacement
Warning
To avoid bodily injury, do not attempt to troubleshoot your server problem if:
- The power cords or plugs are damaged
- Liquid has been spilled into your server
- Your server was dropped
- The case was damaged
Instead, unplug your server and contact a qualified computer technician.
If you have problems after installing a new CMOS battery, try each of the following items, closing
the case and restarting the server after each try:
•
Restart your server, then open the BIOS Setup utility by pressing and holding F2 while your
server restarts. Correct any discrepancies.
•
Remove the top panel by following the instructions in “Opening the server case” on
page 19, then make sure that all cables inside the case are attached securely. Also, make
sure that the colored cable edges are aligned correctly and that the connectors do not miss
any pins.
•
If you have the correct test equipment, make sure that the new battery has power.
Although unlikely, your new battery may be defective.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6: Troubleshooting
Beep codes
Whenever a recoverable error occurs during the power-on self-test (POST), the BIOS displays an
error message that describes the problem. The BIOS also sounds a beep code (one long tone
followed by two short tones) during POST if the video configuration fails (a faulty video controller)
or if an expansion card is not functioning correctly. One short beep indicates the BIOS will boot
the operating system. No error found.
A PCI expansion card (for example, a RAID controller) can also issue audible errors by itself, usually
consisting of one long tone followed by a series of short tones. For more information on the
beep codes issued, check the documentation for that device.
The following table shows POST error beep codes. Prior to system video initialization, BIOS uses
these codes to inform you of error conditions.
Beeps
Description
Troubleshooting steps
1
Memory refresh timer error
Reseat the memory modules or replace with
modules you know are good.
2
3
4
Parity error in the first 64 KB of memory.
Base memory read/write test error
System board timer not operational.
Same as for 1 beep.
Same as for 1 beep.
Possible system board malfunction. To eliminate
the possibility of an add in-card problem,
remove all expansion cards.
If the beep code occurs even when all expansion
cards have been removed, the system board is
at fault.
If the beep code does not occur when the
expansion cards have been removed, one of the
cards is causing the problem. Install the cards
one at a time until the problem happens again.
When the beep code returns, the most recent
card you installed is at fault.
5
6
A processor on the system board generated an
error.
Remove one of the processors if two are
installed, then try a known good processor in
the first socket.
Same as for 4 beeps.
The keyboard controller (8042) may be
defective. The BIOS cannot switch to Protected
mode.
Remove the keyboard to see if the error goes
away. If it does, try a known good keyboard.
Same as for 4 beeps.
7
8
General exception error (processor exception
error).
Same as for 5 beeps
Display memory error (system video adapter).
If the system video adapter is an add-in card,
replace or reseat the video adapter. If the video
adapter is integrated into the system board, the
board may be faulty. Try using an add-in card.
9
The ROM checksum value does not match the
value encoded in the BIOS.
Same as for 4 beeps.
10
11
The shutdown register for CMOS RAM failed.
The cache memory test failed.
Same as for 4 beeps.
Same as for 4 beeps.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
LED information
See the following table for a description of this server’s LEDs and the information they provide:
LED Name
Function
Location
Color
Description
ID
Aid in server
identification
Control panel and
back of system
board
Yellow
On - Server identification
enabled
(front)
Blue (back)
System Fault
Visible fault
warning
Control panel
Red
Off - System normal
Blinking - Non-critical system
fault
On - Critical system fault
(system needs to be shut down
and serviced)
Hard drive tray
LEDs
Indicate drive
On each hard drive Blue or red
Blue (On) - Hard drive present
Blue (Blinking) - Hard drive
activity
status and activity tray
Red (On) - Hard drive fault
Red (Blinking) - Hard drive
rebuilding
Off - No hard drive access
NIC status LEDs Identify NIC states Control panel and
Blue (front)
Blue (On) - Link
Blue (Blink) - Activity
Off - No link
back I/O panel
RJ-45 connectors
LED 1 Green (On) - NIC linked
LED 1 Green (Blinking) - NIC 1
Gbps activity
Green/
Orange
(back)
LED 1 (Off) - No link
LED 2 Orange (On) Link speed
1 Gbps
LED 2 Green (On) - Link at
100 Mbps
LED 2 Green (Off) - Link at
10 Mbps
Power LED
Identify the power Control panel
state of the system
Blue
Off - Power is off
Blinking - Power saving state
(S1, S3, or S4)
On - Power is on
AC power LED
Identify power
supply fault
Power supply
module
Green or
Orange
Green (On) - Power supply good
and receiving power
Orange (On) - Power supply
critical event causing shutdown
Orange (Blinking) - Close to
protection threshold or over
within 15 seconds
Off - Power supply not receiving
power
59
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6: Troubleshooting
BIOS
The settings in the BIOS Setup utility are not retained
•
Optical drive
Your server does not recognize an optical drive
•
Restart your server, then open the BIOS Setup utility by pressing and holding F2 while your
server restarts. Make sure that the IDE controllers are enabled. For more information, see
•
•
Reinstall the device driver. For instructions, see Using Your Server Companion DVD.
Make sure that the drive is configured correctly by following the instructions in the drive’s
documentation.
•
Turn off your server, then remove the drive and push it in again to make sure the drive
is seated correctly. For instructions, see “Installing or replacing a fixed or removable-media
Your optical drive tray does not open
•
Press a straightened paper clip wire into the optical drive’s manual eject hole. The drive
tray opens.
•
If this problem happens frequently while the server is turned on, the drive may be defective.
Expansion cards
Your server does not recognize an expansion card
•
•
Restart your server.
Make sure that you have installed the necessary software or driver. For instructions, see
the card’s documentation.
•
Reseat the expansion card and riser card. For instructions, see “Installing PCI expansion
Hard drive
The hard drive cannot be accessed, or you receive a “General failure reading drive C” error
message
•
If a diskette is in the diskette drive, eject it and restart your server by pressing the reset
button.
•
•
Restart your server by pressing the reset button.
Turn off your server, then remove all hard drives and push them in again to make sure
the drives are seated correctly. For instructions, see “Installing or replacing a hard drive”
•
If your server has been subjected to static electricity or physical shock, you may need to
reinstall the operating system.
You receive a “Non-system disk” or “disk error” error message
•
•
Eject the diskette from the diskette drive, then press ENTER.
Make sure that your hard drive has an active partition. For more information, see “The
60
Download from Www.Somanuals.com. All Manuals Search And Download.
You are having problems with a SATA drive
•
For normal SATA drives (not SATA RAID), check the BIOS setup utility to see if the BIOS has
recognized the drive.
•
•
•
•
Make sure that the power cable and SATA cables are attached securely to the drive cage.
If the drive is not detected, try a different SATA port.
Try swapping SATA cables between drives to determine if the cable is defective.
Try listening to the drive to determine if the drive is spinning up. If not, the drive may be
defective.
The master boot record is corrupted
•
In a Windows network operating system, repair the master boot record using FDISK.
To repair the master boot record:
•
At the command prompt, type fd isk/ m br, then press ENTER.
Internet
You cannot connect to the Internet
•
Make sure that your account with your Internet Service Provider (ISP) is set up correctly.
Contact your ISP technical support for help.
•
Make sure that you do not have a problem with your modem.
Keyboard
Liquid has been spilled into the keyboard
•
If you spilled liquid in the keyboard, turn off your server and unplug the keyboard. Clean
the keyboard and turn it upside down to drain it. Let the keyboard dry before using it
again. If the keyboard does not work after it dries, you may need to replace it. This type
of damage is not covered by your server’s warranty.
Memory
Monitor
Memory errors were detected during server start up
•
Open your server and make sure that the memory modules are installed correctly. For
•
A memory module may be defective. If possible, try another memory module and see if
the error repeats.
Your server is running but there is no picture
•
•
Adjust the brightness and contrast controls to the center position.
Make sure that the monitor is plugged in and turned on. If the monitor is turned on, the
power LED should be lit.
•
•
Check the cable for bent or damaged pins.
Connect your monitor to another computer, or connect a monitor that you know works
to your server.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6: Troubleshooting
The color is not uniform
Make sure that the monitor warms up for at least 30 minutes before making a final judgment
about color uniformity.
Make sure that:
•
•
The monitor is not positioned too close to another monitor, electric fan, or fluorescent light.
You demagnetize the screen using the monitor’s degauss feature. For more information
on degauss, see the monitor’s documentation.
A horizontal line or wire is visible across the CRT monitor screen
The monitor may use thin damper wires, located approximately 1/3 of the way from the upper
and lower screen edges, to stabilize the internal aperture grille. These wires are most obvious
when the monitor displays a white background. The aperture grille allows more light to pass
through the screen for brighter colors and greater luminescence. The damper wire is a critical
part of the overall monitor design and does not negatively affect the monitor’s function.
Power
You press the power button, but the server does not turn on
•
If the power button LED is green, the server is turned on, but you may not be seeing an
•
If your server is plugged into a surge protector or UPS, make sure that the surge protector
or UPS is connected securely to an electrical outlet, turned on, and working correctly. One
way to check this is to plug the server directly into a wall outlet, bypassing the surge
protector or UPS.
•
•
Make sure that the electrical outlet is working by plugging a working device, such as a
lamp, into the outlet, then turning it on to test the outlet.
Open your server and make sure that the power supply module cage cable is connected
correctly to the system board.
When you turn on the server, it makes several short beeps
•
The short beeps indicate the server has encountered some type of error. See “Beep codes”
Processor
Your server does not recognize a new processor
•
Make sure that the processor is fully seated in its socket. The processor should be
recognized automatically if it is installed correctly.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A: Server Specifications
The following specifications are for the standard configuration. Your server may contain optional
equipment. All specifications are subject to change.
System specifications
Tower (with standard power supply): 8 × 16.5 × 19.8 inches
Case size
(203.2 × 419.2 × 502.7 cm)
Tower (with redundant power supplies) 8 × 16.5 × 22.2 inches
(203.2 × 419.2 × 563 cm)
Approximately 32 lbs (14.5 kg) (varies by configuration)
Weight
Fans
■
PS/2 keyboard/mouse (2)
Ports
■
USB (6)
■
Serial (1)
■
VGA (1)
■
RJ-45 LAN (2)
Two 5.25” external drive bays.
Two 3.5” external drive bays.
Optional drives:
Drives
(removable
media)
■
3.5-inch diskette
■
CD-ROM, CD-R, or DVD-ROM
■
Tape drive
Support for as many as four 3.5” SATA, SATA II, or SAS drives
Hard Drives
Supports full-height PCI expansion cards up to 10.8 inches (27.5 cm) long
Single 400 W fixed power supply (standard), or
Two 520 W, hot-swap, redundant power supply modules (optional).
Power supply
modules
Operating
systems
■
■
■
Red Hat Linux Enterprise 4.0 32/64 bit Editions
SuSe Linux Enterprise 10.0 32/64 bit Editions
■
■
FCC Class B
Certifications
■
UL
■
cUL
System board specifications
Single AM2 socket
Supports one (1) AMD Athlon or one (1) AMD Opteron 1200 Series processor
with 3.0 GHz Hyper Transport Bus
NVIDIA nFORCE 3600 (MCP55 Professional)
Four DIMM slots support as many as 8 GB total memory
DDR2 667Mhz ECC Unbuffered DIMM modules
DIMM organization x72 ECC
Memory
240-pin DIMMs (256 MB, 512 MB, 1 GB, or 2 GB only)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
PCI slots:
PCI device/slot
■
Slot 1 - PCI Express x16
■
Slot 2 - PCI Express x4
■
Slot 3 - PCI Express x8
■
Slot 4 - PCI 32-bit
■
Slot 5 - PCI 32-bit
Integrated Matrox G200 Graphics Core with 2.25 MB
Up to 1280 × 1024, 8 bpp or 1024 × 768, 16 bpp
Video
RAID
LAN
Six Serial ATA 2.0 ports from the MCP55 supporting entry level RAID
functionality, including RAID levels 0, 1, 5, and 10.
On-board Marvel Ethernet NIC
■
10Base-T/100Base-TX/1000Base-T
PXE support
■
ACPI compliance
Supports S0 and S4
ACPI
Main logic board sensors:
Hardware
Monitor
■
Voltage sensors
■
Temperature sensors
■
Adaptive fan speed control and fan speed detection
Environmental specifications
The following specifications identify maximum environmental conditions. At no time should the
server run under conditions which violate these specifications.
Variable
Requirements
Maximum rate of change: 18°F (10°C) per hour
Nonoperating: -4° to 140°F (-20° to 60°C)
Operating: 41° to 95°F (5° to 35°C); derated 0.9°F (0.5°C) for every
1,000 feet (305 meters)
Temperature
12,500 feet (3,810 meters) maximum
Altitude
Operating: 20% to 80% relative, non-condensing
Nonoperating: 20% to 90% relative non-condensing at 86° F (30° C)
Humidity
Operating: 2.0 g, 11 msec, ½ sine
Packaged: Operational after 18-inch free fall (cosmetic damage might
occur)
Shock
100-127 V, 10.0 A, 50/60 Hz max.
200-240 V, 5.0 A, 50/60 Hz max.
AC input power
65
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A: Server Specifications
Electronic specifications
Memory map
Address Range (hex)
0 to 07FFFFh
Amount
640 KB
128 KB
128 KB
128 KB
2 MB
Function
DOS region, base system memory
Video or SMM memory
Expansion card BIOS and buffer area
System BIOS
0A0000h to 0BFFFFh
0C0000h and 0DFFFFh
0E0000h to 0FFFFFh
0E0000h to 0EFFFFh
FC000000h to FFFFFFFFh
Extended system BIOS
PCI memory space
64 MB
Interrupts
The following table reflects a typical configuration, but you can change these interrupts. Use this
information to determine how to program each interrupt. The actual interrupt map is defined
using configuration registers in the ICH5-R (I/O controller). I/O Redirection Registers in the I/O
APIC are provided for each interrupt signal. The signals define hardware interrupt signal
characteristics for APIC messages sent to local APIC(s).
Important
If you disable an IDE controller to free the interrupt for that controller, you must
physically unplug the IDE cable from the system board. Simply disabling the drive by
configuring the BIOS does not make the interrupt available.
I
Interrupt
Description
IRQ0
Timer/counter, HPET #0 in legacy
replacement Mode. In APIC mode, cascade
from 8259 controller 1
IRQ1
IRQ2
Keyboard controller
Slave controller INTR output. In APIC mode
Timer/counter, HPET #0
IRQ3
IRQ4
IRQ5
IRQ6
IRQ8
Serial port A
Serial port B
Parallel port
Diskette controller
Real-time clock/HPET#1 in legacy
replacement mode
IRQ9
Generic, Option for SCI
Generic, Option for SCI
HPET #2, option for SCSI, TCO
Mouse controller
IRQ10
IRQ11
IRQ12
IRQ13
System interrupt/FERR
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Interrupt
IRQ14
PIRQA
PIRQB
PIRQC
PIRQD
PIRQE
PIRQF
Description
Primary ATA, legacy mode
USB 1.1 controller 1 and 4
Video
USB 1.1 controller 3, Native IDE, SATA
USB 1.1 controller 2
Option for SCI, TCO, HPET #0,1,2
Option for SCI, TCO, HPET #0,1,2
Option for SCI, TCO, HPET #0,1,2
PIRQG
PIRQH
USB 2.0 EHCI controller 1, Option for SCI,
TCO, HPET #0,1,2
Ser IRQ
SIO3
Additional specifications
For more information about your server, such as memory size, hard drive size, and processor
type, visit Gateway’s Support page at support.gateway.com. The Support page also has links to
additional Gateway documentation and detailed specifications for your own server.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A: Server Specifications
68
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B: BIOS Settings
If you ever need to restore your BIOS settings, such as after a system board change, a record
of the settings will make the process much easier. You can print this appendix, then record your
custom BIOS settings on the printout. Only settings which can be changed are listed. For a
complete list of viewable BIOS settings, run the BIOS Setup utility.
To view all BIOS settings:
1
2
Restart your server
Press F2 when the Gateway logo screen appears during startup. The BIOS Setup utility
opens.
3
Select menus and submenus to display setting information.
Caution
Setting the wrong values in the Advanced Menu may cause the server to
malfunction.
BIOS menu
Main
BIOS submenu
Setting
Value
System Overview
AMIBIOS (Version, Build date,
System ID, Version), Processor
(Type, Speed, Count)
System Memory (Size)
System Time
HH:MM:SS
System Date
DAY MM/DD/YYYY
Advanced
CPU Configuration
Module Version
Physical count
Logical count
Manufacturer and type
Revision
Cache L1
Cache L2
Speed
Current FSB Multiplier
Maximum FSB Multiplier
Able to Change Freq.
uCode Patch Level
GART Error Reporting
Enabled
Disabled
MTRR Mapping
Continuous
Discrete
Memory
Configuration
70
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS menu
BIOS submenu
Setting
Value
Memory Performance Mode
Non-Redundant
Interleaved
Single Channel
Mirror
Mirrors branch space
Between branches
Total Memory Capacity
Memory Redundancy
Non-Redundant
Mirror
DIMM 1
DIMM 2
DIMM 3
DIMM 4
(Size)
(Not Installed)
(Size)
(Not Installed)
(Size)
(Not Installed)
(Size)
(Not Installed)
IDE Configuration
OnBoard IDE Controller
Serial-ATA Devices
Disabled
Enabled
Disabled
Device 0
Device 0/1
Device 0/1/2
nVidia RAID Setup
Primary IDE Master
Selects RAID Setup
sub-menu.
(auto-detected)
Selects IDE
sub-menu.
Primary IDE Slave
(auto-detected)
Selects IDE
sub-menu.
Serial-ATA 0 Primary Channel
(auto-detected)
Selects IDE
sub-menu.
Serial-ATA 0 Secondary
Channel
(auto-detected)
Selects IDE
sub-menu.
Serial-ATA 1 Primary Channel
(auto-detected)
Selects IDE
sub-menu.
Serial-ATA 1 Secondary
Channel
(auto-detected)
Selects IDE
sub-menu.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B: BIOS Settings
BIOS menu
BIOS submenu
Setting
Value
Serial-ATA 2 Primary Channel
(auto-detected)
Selects IDE
sub-menu.
Serial-ATA 2 Secondary
Channel
(auto-detected)
Selects IDE
sub-menu.
Hard Disk Write Protect
Disabled
Enabled
IDE Detect Time Out (Sec)
ATA(PI) 80Pin Cable Detection
0, 5, 10, 15, 20, 25, 30,
35
Host & Device
Host
Device
Super I/O
Configuration
Onboard Floppy Controller
Floppy A
Disabled
Enabled
Disabled
1.44 MB 3½”
2.88 MB 3½”
Serial Port 1 Address
Serial Port 1 IRQ
Disabled
3F8
2F8
3E8
2E8
IRQ3
IRQ4
IRQ10
IRQ11
PS/2 Keyboard
PS/2 Mouse
Present
Present
IPMI 2.0
Configuration
(Nothing shown)
Remote Access
Configuration
(Nothing shown)
USB Configuration
USB Devices Enabled (List of
USB devices detected by BIOS)
Legacy USB Support
Disabled
Enabled
Auto
USB 2.0 Controller Mode
BIOS EHCI Hand-Off
FullSpeed (12 Mbps)
HiSpeed (480 Mbps)
Disabled
Enabled
72
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS menu
BIOS submenu
Setting
Value
USB Mass Storage Device
Configuration
Selects USB Mass
submenu with USB
Device enable
PCI Configuration
NIC 1 PXE Option ROM
NIC 2 PXE Option ROM
NIC 3 PXE Option ROM
NIC 4 PXE Option ROM
NIC 5 PXE Option ROM
NIC 6 PXE Option ROM
PCIe Port1 Option ROM
PCIe Port2 Option ROM
PCIe Port3 Option ROM
PCI-X Port1 ROM
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Boot
Boot Settings
Configuration
Quick Boot
Disabled
Enabled
Quiet Boot
Disabled
Enabled
Wait For ‘F1 If Error
Hit ‘F2’ Message Delay
Disabled
Enabled
Disabled
Enabled
Boot Device Priority
1st Boot Device
nth Boot Device
Varies (Specifies boot
sequence from the
available devices.)
Varies (Specifies boot
sequence from the
available devices.)
Hard Disk Drives
73
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B: BIOS Settings
BIOS menu
BIOS submenu
Removable Drive
CD/DVD Drives
Setting
Value
1st Drive
Varies (Specifies boot
sequence from the
available devices.)
nth Drive
Varies (Specifies boot
sequence from the
available devices.)
1st Drive
nth Drive
Varies (Specifies boot
sequence from the
available devices.)
Varies (Specifies boot
sequence from the
available devices.)
1st Drive
nth Drive
Varies (Specifies boot
sequence from the
available devices.)
Varies (Specifies boot
sequence from the
available devices.)
Security
Supervisor Password
(Installed/Not installed)
User Password (Installed/Not
installed)
Change Supervisor Password
(Set or clear Supervisor
password)
User Access Level
No Access
View Only
Limited
Full Access
Change User Password (Set or
clear User password)
Password Check
Disabled
Enabled
Boot Sector Virus Protection
Disabled
Enabled
Power & Reset Switches Inhibit Disabled
Enabled
NMI control switch inhibit
Disabled
Enabled
Server
Remote Access
Configuration
74
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS menu
BIOS submenu
Setting
Value
Remote Access
Disabled
Enabled
Serial Port Number (Base
address and IRQ)
COM1
Serial Port Mode
115200 8,n,1
57600 8,n,1
19200 8,n,1
09600 8,n,1
Flow Control
None
Hardware
Software
Redirection After BIOS POST
Terminal Type
Disabled
Boot Loader
Always
ANSI
VT100+
VT-UTF8
VT-UTF8 Combo Key Support
Disabled
Enabled
IPMI Configuration
Status of BMC
BMC Firmware Revision
View BMC Event Log
Provides data on
event log
Clear BMC System Event Log
Disable PEF
No
Yes
Restore on AC Power
Loss
Power Off
Power On
Last State
Wake on RING
function
Disabled
Enabled
Exit
Save Changes and Exit (F10)
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Custom Defaults
Save Custom Defaults
The following second level submenus are accessed from the submenu indicated in the first
column.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B: BIOS Settings
BIOS submenu
BIOS 2nd level
Setting
Value
submenu
IDE
Configuration
RAID Setup
nVidia RAID Function
Enabled
Disabled
SATA 0 Primary Channel
SATA 0 Secondary Channel
SATA 1 Primary Channel
SATA 1 Secondary Channel
SATA 2 Primary Channel
SATA 2 Secondary Channel
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
BIOS submenu
BIOS 2nd level
submenu
Setting
Value
IDE
Configuration
Primary IDE Master
(All IDE drives)
(Below is shown information
and options appropriate to
drive type)
Device
Device information
Device vendor
Vendor
Size
Device size
LBA Mode
Block Mode
PIO Mode
Async DMA
Ultra DMA
S.M.A.R.T.
Type
Device LBA mode
Device block mode
Device PIO mode
Device Async DMA mode
Device Ultra DMA mode
Device S.M.A.R.T. support
Not Installed
Auto
CD/DVD
ARMD
LBA/Large Mode
Disabled
Auto
Block (Multi-Sector Transfer)
Mode
Disabled
Auto
76
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS submenu
BIOS 2nd level
Setting
Value
submenu
PIO Mode
Auto
0
1
2
3
4
DMA Mode
Auto
SWDMA 0-2
MWDMA 0-2
UWDMA 0-6
S.M.A.R.T.
Auto
Disabled
Enabled
32Bit Data Transfer
Disabled
Enabled
BIOS submenu
BIOS 2nd level
submenu
Setting
Value
USB
Configuration
USB Mass Storage
Device Configuration
USB Mass Storage Reset Delay 10 Sec
20 Sec
30 Sec
40 Sec
Device #1
Only displayed if a device
is detected. Includes a
DeviceID string returned
by the USB device.
Emulation Type
Auto
Floppy
Forced FDD
Hard Disk
CDROM
Device #n
Only displayed if a device
is detected. Includes a
DeviceID string returned
by the USB device.
Emulation Type
Auto
Floppy
Forced FDD
Hard Disk
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety information
Warning
Always follow these instructions to help guard against personal injury and damage
to your Gateway system.
Your Gateway system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the
safety instructions marked on the product and in the documentation are followed.
Setting up your system
Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use.
Do not use this product near water or a heat source such as a radiator.
Set up the system on a stable work surface.
The product should be operated only from the type of power source indicated on the rating label.
If your computer has a voltage selector switch, make sure that the switch is in the proper position for your area. The voltage selector switch is set at the factory to the correct voltage.
Openings in the computer case are provided for ventilation. Do not block or cover these openings. Make sure you provide adequate space, at least 6 inches (15 cm), around the system for
ventilation when you set up your work area. Never insert objects of any kind into the computer ventilation openings.
Some products are equipped with a three-wire power cord to make sure that the product is properly grounded when in use. The plug on this cord will fit only into a grounding-type outlet.
This is a safety feature. If you are unable to insert the plug into an outlet, contact an electrician to install the appropriate outlet.
If you use an extension cord with this system, make sure that the total ampere rating on the products plugged into the extension cord does not exceed the extension cord ampere rating.
If your system is fitted with a TV Tuner, cable, or satellite receiver card, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges
and buildup of static charges.
■
■
■
■
■
■
■
■
■
Care during use
Do not walk on the power cord or allow anything to rest on it.
■
■
Do not spill anything on the system.
■
Some products have a replaceable CMOS battery on the system board. There is a danger of explosion if the CMOS battery is replaced incorrectly. Replace the battery with the same or
equivalent type recommended by the manufacturer. Dispose of batteries according to the manufacturer’s instructions.
When the computer is turned off, a small amount of electrical current still flows through the computer. To avoid electrical shock, always unplug all power cables and modem cables from the
wall outlets before cleaning the system.
■
Warning
This unit has two power supplies. To remove power from all internal circuitry you
must disconnect both power cords.
■
Unplug the system from the wall outlet and refer servicing to qualified personnel if:
■
The power cord or plug is damaged.
Liquid has been spilled into the system.
The system does not operate properly when the operating instructions are followed.
The system was dropped or the cabinet is damaged.
■
■
■
■
The system performance changes.
Replacement parts and accessories
Use only replacement parts and accessories recommended by Gateway.
Warning
To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line
cord.
Important
Do not use Gateway products in areas classified as hazardous locations. Such areas
include patient care areas of medical and dental facilities, oxygen-laden environments, or
industrial facilities.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory compliance statements
United States of America
Federal Communications Commission (FCC)
Unintentional emitter per FCC Part 15
FCC Part 15 Class B Statement
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
■
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment to an outlet on a different circuit from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
■
■
■
Compliance Accessories: The accessories associated with this equipment are: shielded video cable when an external monitor is connected. These accessories are required to be used in order
to ensure compliance with FCC rules.
Caution
Changes or modifications not expressly approved by Gateway could void the FCC
compliance and negate your authority to operate the product.
Telecommunications per FCC part 68
(applicable to products fitted with USA modems)
Your modem complies with Part 68 of the Federal Communications Commission (FCC) rules. On the computer or modem card is a label that contains the FCC registration number and Ringer
Equivalence Number (REN) for this device. If requested, this information must be provided to the telephone company.
An FCC-compliant telephone line cord with a modular plug is required for use with this device. The modem is designed to be connected to the telephone network or premises wiring using a
compatible modular jack which is Part 68-compliant. See installation instructions for details.
The Ringer Equivalence Number (REN) is used to determine the number of devices which may be connected to the telephone line. Excessive RENs on a telephone line may result in the devices
not ringing in response to an incoming call. In most areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by
the total RENs, contact the local telephone company.
If this device causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. The telephone company may
request that you disconnect the equipment until the problem is resolved.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will
provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
This equipment cannot be used on telephone company-provided coin service. Connection to party line service is subject to state tariffs. Contact the state public utility commission or public
service commission for information.
When programming or making test calls to emergency numbers:
■
Remain on the line and briefly explain to the dispatcher the reason for the call.
Perform such activities in the off-peak hours such as early morning or late evenings.
■
The United States Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine
unless such message clearly contains, in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent, an identification of the
business, other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. Refer to your fax
communication software documentation for details on how to comply with the fax-branding requirement.
FCC declaration of conformity
Responsible party:
Gateway Companies, Inc.
610 Gateway Drive, North Sioux City, SD 57049
(605) 232-2000 Fax: (605) 232-2023
Product:
■
Gateway E-9232T Server
For unique identification of the product configuration, please submit the 10-digit serial number found on the product to the responsible party.
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C: Legal Information
Caution
Changes or modifications not expressly approved by Gateway could void the FCC
compliance and negate your authority to operate the product.
UL Warning
Before removing or installing the chassis cover, make sure that the system power is not turned on or connected to AC power.
Canada
Industry Canada (IC)
Unintentional emitter per ICES-003
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe A prescrites dans le règlement sur le brouillage
radioélectrique édicté par Industrie Canada.
Telecommunications per Industry Canada CS03
(for products fitted with an IC-compliant modem)
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety
requirements. The Department does not guarantee the equipment will operate to the users’ satisfaction.
Before installing this equipment, users should make sure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed
using an acceptable method of connection. In some cases, the inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly. The
customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Warning
To avoid electrical shock or equipment malfunction do not attempt to make electrical
ground connections by yourself. Contact the appropriate inspection authority or an
electrician, as appropriate.
Users should make sure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural areas.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Laser safety statement
All Gateway systems equipped with CD and DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser
Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact an authorized service location.
Warning
Use of controls or adjustments or performance of procedures other than those
specified in this manual may result in hazardous radiation exposure. To prevent exposure
to laser beams, do not try to open the enclosure of a CD or DVD drive.
California Proposition 65 Warning
Warning
This product contains chemicals, including lead, known to the State of California to
cause cancer and/or birth defects or reproductive harm.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental information
The product you have purchased contains extracted natural resources that have been used in the manufacturing process. This product may contain substances known to be hazardous to the
environment or to human health.
To prevent releases of harmful substances into the environment and to maximize the use of our natural resources, Gateway provides the following information on how you can responsibly
recycle or reuse most of the materials in your “end of life” product.
Waste Electrical and Electronic Equipment (commonly known as WEEE) should never be disposed of in the municipal waste stream (residential garbage collection). The “Crossed-Out Waste Bin”
label affixed to this product is your reminder to dispose of your “end of life” product properly.
Substances such as glass, plastics, and certain chemical compounds are highly recoverable, recyclable, and reusable. You can do your part for the environment by
following these simple steps:
■
When your electrical or electronic equipment is no longer useful to you, “take it back” to your local or regional waste collection administration for recycling.
In some cases, your “end of life” product may be “traded in” for credit towards the purchase of new Gateway equipment. Call Gateway to see if this program is
available in your area.
If you need further assistance in recycling, reusing, or trading in your “end of life” product, you may contact us at the Customer Care number listed in your product’s
user guide and we will be glad to help you with your effort.
■
■
Finally, we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable),
recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic equipment, minimize the use of landfills for the disposal of “end of life” products, and
generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly.
Notices
Copyright © 2007 Gateway, Inc.
All Rights Reserved
7565 Irvine Center Drive
Irvine, CA 92618-2930 USA
All Rights Reserved
This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any form, without prior consent in writing from
Gateway.
The information in this manual has been carefully checked and is believed to be accurate. However, changes are made periodically. These changes are incorporated in newer publication
editions. Gateway may improve and/or change products described in this publication at any time. Due to continuing system improvements, Gateway is not responsible for inaccurate
information which may appear in this manual. For the latest product updates, consult the Gateway Web site at www.gateway.com. In no event will Gateway be liable for direct, indirect,
special, exemplary, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages.
In the interest of continued product development, Gateway reserves the right to make improvements in this manual and the products it describes at any time, without notices or obligation.
Trademark Acknowledgments
Trademarks used herein are trademarks or registered trademarks of Gateway, Inc. in the United States and other countries. All other brands and product names are trademarks or registered
trademarks of their respective companies.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
location
configuring 25
Numerics
5.25-inch drive
DVD
cleaning
installing 25
keyboard 12
screen 12
location
replacing 25
servers 12
A
accessories
tape 13
see battery
troubleshooting 60
add-in card
conditioner
see card
DVD
line
configuring
DVD drive
Advanced menu
see CD or DVD drive
connections
keyboard
E
B
LAN
battery
lock slot
monitor
mouse
troubleshooting 57
network
parallel
power
bezel assembly
installing 23
removing 20
Exit menu
RJ-45
serial
expansion card
BIOS
see card
recovering 49
settings 69
VGA
F
control panel
location
fans
troubleshooting 60
installing 42
cover panel
BIOS Setup utility
location
removing 19
rear
replacing 24
opening 48
replacing 42
cover release latch
location
settings 70
G
D
troubleshooting 60
Gateway
DDR SDRAM
see memory
BMC
Web address
device drivers
recovering 50
installing 15
boot
DIMM
device
H
see memory
menu
hard drive
indicator
LED indicator
troubleshooting 60
heat sink
installing 38
diskette drive
Boot menu
location
display
troubleshooting 61
documentation
Gateway Web site
drive bays
location
drivers
installing 15
drives
C
card
installing 35
help
reseating 35
retention levers
tutoring 53
hot-swap
troubleshooting 60
case
hot-swap drives
interior
opening 19
location
CD or DVD drive
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
I
cord connector
IDE
M
cables 25
LED
Main menu
line conditioners
protecting from surges
reset button
indicators
LED
maintenance
cleaning 12
information
LED 59
installing
source problems
recording BIOS configuration
troubleshooting 62
card 35
uninterruptible power supply
(UPS)
power supply
uninterruptible
fans 42
power supply module
memory
installing 40
power/sleep LED
installing 34
map 66
power-on self-test
troubleshooting 61
processor
installing 38
replacing 38
memory 34
messages 53
monitor
cleaning 12
troubleshooting 62
processor 38
port
troubleshooting 61
motherboard
see system board
mouse port
R
interior
RAID configuration
case
Internet connection
RAM
troubleshooting 61
see memory
N
interrupts 66
rear fan
recovering
BIOS 49
BMC 50
removing
see installing
network jack
NMI 57
J
jacks
O
see connections
onboard RAID
replacing
configuring 28
fans 42
K
processor 38
see installing
Kensington lock slot
keyboard
resources
cleaning 12
interrupts 66
operating system
port
troubleshooting 61
RJ-45 jack
optical drive
troubleshooting 60
L
S
LAN jack
LED
P
safety
guidelines for
parallel port
password
information 59
power/sleep
troubleshooting 53
supervisor 14
user 14
LEDs
screen
cleaning 12
ports
line conditioners
lock
troubleshooting 61
see connections
POST (power-on self-test)
power
SDRAM
see memory
security
Kensington
key
86
Download from Www.Somanuals.com. All Manuals Search And Download.
system 14
resources 52
training
CD 53
Security menu
Gateway Learning Libraries
troubleshooting
battery 57
serial port
BIOS 60
Server menu
card 60
setting up
hardware
Setup utility
see BIOS Setup utility
keyboard 61
sparing
memory 61
electronic 66
monitor 61
environmental 65
power 62
starting server
power source problems
processor 62
supervisor password
video 61
see administrator password
Support 67
system 64
administration 13
control 13
turning on server
security 14
specifications 64
U
startup
uninterruptible power supply
system board
components
installing 44
replacing 44
(UPS)
UPS
USB ports
specifications 64
thumbscrew location
system configuration
protecting with passwords
V
VGA port
system recovery
W
recording BIOS configuration
Web site
Gateway
T
tape drive
cleaning 13
technical support
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
A MAN E-9232T USR GDE R1 9/ 07
Download from Www.Somanuals.com. All Manuals Search And Download.
|