Garmin Marine Instruments 190 01015 01 User Manual

GMI10  
quick start manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Unit Overview  
Instrument screen  
Power  
Back  
Soft keys  
Power—press and hold to power the unit on and off. Press and quickly  
release to adjust display settings.  
Soft Keys—used to navigate the menus and select items on the GMI 10.  
Typically, the left and right soft keys cycle data on the instrument screen and  
navigate menu screens, and the center soft key selects highlighted items and  
opens the Menu.  
Back—used to move back one menu screen. Press and hold to move all the  
way back to the instrument screen from any menu screen.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Information  
Instrument screens are organized  
by category. Categories match the  
data available on an instrument,  
such as depth instruments. You can  
configure the GMI 10 to mix data  
from common instruments to make  
a custom instrument tailored to the  
sensors on your boat.  
Using the GMI 10  
Use the GMI 10 to view numerical  
data provided by connected sensors.  
Many data types can also be  
displayed as an analog gauge.  
The types of data available  
are determined by the sensors  
connected to the GMI 10 either  
through NMEA 2000 or  
NMEA 0183.  
Each category can contain a variety  
of screens that you can quickly  
cycle through.  
For example, when connected to a  
GPS antenna such as a GPS 17x,  
the GMI 10 can show GPS  
position, GPS heading (COG),  
GPS speed (SOG), average speed,  
maximum speed obtained, and  
distance traveled (trip odometer)  
information.  
Selecting an Instrument  
Screen Category  
Change the instrument screen to a  
different category from the menu:  
1. From the instrument screen,  
select Menu > Setup > Set  
Instrument Type.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Choose from the categories  
listed below.  
Custom—arrange a custom  
set of instruments. Utilize an  
existing instrument or graph,  
or create a custom instrument  
screen.  
Surface—GPS or water  
speed, GPS heading or  
magnetic sensor heading,  
and odometer.  
Cycling Through  
Instrument Screens in a  
Category  
When viewing a category, use the  
soft keys under the left and right  
arrows to cycle through the screens  
available in that category.  
Water—depth and water  
temperature.  
Fuel—level, rate, range, and  
economy.  
Wind—wind speed and  
angle, ground wind speed  
and direction, wind velocity  
made good (VMG), race  
timer, wind and weather  
graphs, barometric pressure,  
and air temperature.  
Engine—RPM, fuel  
flow, trim, temperature,  
pressure, voltage, hours,  
neutral indicator, and status  
indicators.  
Cycle through instrument screens  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To change additional options  
on an instrument screen:  
1. From the instrument screen,  
select Menu.  
Changing Instrument  
Screen Options  
Data provided on an instrument  
screen is represented numerically. In  
many cases, a numerical value can  
be shown as an analog gauge or as a  
graph, and vice versa (not available  
on all instrument screens).  
2. To change the source sensor,  
select Source, and choose the  
sensor you want to use. For  
example, if you have a GPS  
antenna and a heading sensor,  
you can choose to show either  
GPS Heading (COG) or Heading  
from the heading sensor.  
To change the appearance of  
an instrument screen:  
If the instrument screen is  
showing a number, select  
Menu > Show Gauge or  
Show Graph.  
3. To change additional options,  
such as resetting an odometer,  
adding Trip Speed Graphics to a  
speed gauge, viewing a water-  
temperature graph, or adding  
fuel, select the option you want  
to change.  
If the instrument screen  
is showing a gauge or a  
graph, select Menu > Show  
Number.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Use the soft keys under the left  
and right arrows to cycle through  
the instrument screens available  
in the selected category.  
Understanding Custom  
Instrument Screens  
You can create up to ten of the  
following kinds of customized  
displays on the GMI 10:  
3. Select Select to add a screen.  
To create the first custom  
instrument screen:  
1. From the instrument screen,  
select Menu > Setup > Set  
Instrument Type > Custom >  
Custom Page.  
You can organize individual  
screens found in the predefined  
categories (for multiple  
instruments) to create your own  
customized collection of screens.  
You can select the individual  
fields to show on each screen to  
create customized screens.  
2. Select the number of fields you  
want to show on the custom  
instrument screen (1–4).  
3. Select the data type you would  
To create a customized  
like to show in each field.  
combination of individual  
instrument screens found in  
the predefined categories:  
1. Select Menu > Setup > Set  
Instrument Type > Custom.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To add additional custom  
instrument screens:  
1. From the custom instrument  
screen, select Menu > Add  
Page > Custom Page. (If you  
have more than one custom  
instrument screen, this option  
will appear as Add/Remove  
Page.)  
Select the data for each field  
To add graph screens to your  
customized combination of  
existing instrument screens:  
1. Select Menu > Setup > Set  
Instrument Type > Custom >  
Graphs.  
2. Select the number of fields you  
want to show on the custom  
instrument screen (1–4).  
2. Select Select to add a screen.  
To customize graph screens:  
1. When viewing the graph screen,  
select Menu.  
Select the number of fields  
2. Select Graph Data, Graph  
Duration, or Graph Scale to  
adjust the appearance of the  
graph screen.  
3. Select the data type you would  
like to show in each field.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Select the data type you would  
To remove a previously created  
custom instrument screen:  
1. Navigate to the custom  
instrument screen you want to  
remove.  
like to show in each field.  
NOTE: You can create up to ten  
custom instrument screens and  
cycle through them.  
2. Select Menu > Add/Remove  
Page > Remove Page.  
To change a previously created  
custom instrument screen:  
1. From the custom instrument  
screen you want to change,  
select Menu > Change  
Appearance.  
2. Choose from the following  
options:  
Select Change Page Layout  
to change the number of  
fields and data types in the  
fields.  
Select Change Data Style  
to switch between numerical  
and analog displays.  
3. Select Done when finished.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Choose from the following  
options:  
Customizing System  
Options  
TIP: You must have the appropriate  
sensors connected to view the  
information.  
Auto Magnetic—Automatic  
Magnetic Variation  
automatically sets the  
magnetic declination for your  
acquired GPS position.  
1. To customize system options on  
the GMI 10, from the instrument  
screen, select Menu > Setup >  
System.  
True—sets true north as the  
heading reference.  
User Magnetic—allows you  
to set the magnetic variation  
value.  
2. For the listed options, select the  
appropriate settings or enter the  
necessary values. For example,  
you can select units of measure,  
language, enter total fuel  
To configure the audible  
beeper:  
1. From the instrument screen,  
select Menu > Setup > System  
> Beeper.  
capacity, and so on.  
To set the reference used to  
calculate heading information:  
1. From the instrument screen,  
select Menu > Setup > System  
> Heading.  
2. Select from the following options  
to determine when the GMI 10  
makes audible sounds: Off,  
Alarms Only, On (Keys &  
Alarms).  
10  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To specify how the GMI 10  
utilizes coordinates:  
To specify the speed sensor  
used when performing fuel  
economy calculations:  
1. From the instrument screen,  
select Menu > Setup > System  
> Speed Sources.  
CauTIon: Do not change the  
position format or map datum  
unless you are using a map or  
chart that specifies a different  
position format or map datum.  
2. Select Fuel Economy.  
3. Select the appropriate sensor.  
1. From the instrument screen,  
select Menu > Setup > System  
> Position.  
To specify the speed sensor  
used when performing wind  
calculations:  
1. From the instrument screen,  
select Menu > Setup > System  
> Speed Sources.  
2. Choose from the following  
options:  
Position Format—change  
the coordinate style in which  
a given location reading  
appears.  
2. Select Wind.  
3. Select the appropriate sensor.  
Map Datum—change the  
coordinate system on which  
the position format is based.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Low Fuel—set an alarm  
to sound when the fuel  
remaining (based on fuel-flow  
information from a GFS 10)  
reaches the specified level.  
Setting Alarms  
1. To set alarms on the GMI 10,  
from the instrument screen,  
select Menu > Setup > Alarms.  
2. Select from the following alarm  
types. Select On and enter an  
appropriate value.  
Engine Status—set an alarm  
to sound when an engine  
indicates there is a problem.  
Shallow Water—set an  
alarm to sound when the  
depth is less than the  
specified value.  
Low Apparent Wind  
Speed—set an alarm to  
sound when the apparent  
wind speed is at or below the  
specified speed.  
Deep Water—set an alarm  
to sound when the depth is  
greater than the specified  
value.  
High Apparent Wind  
Speed—set an alarm to  
sound when the apparent  
wind speed is at or above the  
specified speed.  
Surface Temperature—set  
an alarm to sound when  
the transducer reports a  
temperature that is 2°F  
(1.1°C) above or below the  
specified temperature.  
Low True Wind Speed—set  
an alarm to sound when the  
true wind speed is at or below  
the specified speed.  
1ꢀ  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
High True Wind Speed—set  
an alarm to sound when  
the true wind speed is at or  
above the specified speed.  
Battery Voltage—set an  
alarm to sound when the  
battery voltage reaches the  
specified level.  
High Apparent Wind  
Angle—set an alarm to  
sound when the apparent  
wind angle is at or above the  
specified angle.  
Changing the Display  
Options  
1. To change the display options on  
the GMI 10, from the instrument  
screen select Menu > Setup >  
Display.  
Low Apparent Wind  
Angle—set an alarm to  
sound when the apparent  
wind angle is at or above the  
specified angle.  
2. Select a value for the listed  
options.  
TIP: You can also access  
the display options menu by  
pressing and quickly releasing  
the POWER  
instrument screen.  
Low True Wind Angle—set  
an alarm to sound when the  
true wind angle is at or below  
the specified angle.  
button from any  
High True Wind Angle—set  
an alarm to sound when the  
true wind angle is at or above  
the specified angle.  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1ꢁ  
Advanced Sensor  
Configuration  
1. From the instrument screen,  
select Menu > Setup > NMEA  
2000 Devices.  
Changing NMEA 2000  
Device Options  
You can view information about  
your NMEA 2000 devices and  
change available device-specific  
options on the GMI 10.  
2. Select the appropriate sensor.  
Select Config.  
1. From the instrument screen,  
select Menu > Setup > NMEA  
2000 Devices.  
3. Enter the appropriate values for  
the listed options.  
TIP: For more information on  
configuring the sensor, refer to  
the installation instructions for  
the sensor.  
2. You will see a list of all  
connected NMEA 2000  
devices. Select a device to see  
information about the device,  
such as the software version and  
the serial number.  
Honda Engine ECO  
Symbol  
The  
symbol appears when  
boats with NMEA 2000-compatible  
Honda engines are running in a  
fuel-efficient mode and engine RPM  
is displayed.  
1ꢂ  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Consult your Honda engine manual  
to determine if the engine is NMEA  
2000 compatible.  
Lost Satellite Reception—a  
connected GPS antenna has lost  
satellite reception.  
nMEa Depth Is Below  
System Alarms and  
Messages  
noTE: There are several possible  
engine alarms. If the GMI 10  
displays an engine alarm, contact  
your engine manufacturer.  
Transducer—the NMEA depth  
input is using the DBT sentence  
which does not include keel offset.  
nMEa 2000 Device Requires  
Calibration—a NMEA 2000  
device requiring calibration has  
been detected.  
Boat Is not Moving Fast Enough  
to Calibrate—water speed  
calibration – the boat is moving too  
slow to calibrate.  
Simulating operation—the unit  
is in demo mode. Do not drive or  
operate the boat while the GPS  
device is in Demo mode. To change  
the operating mode, select Menu  
> Setup > System > operating  
Mode > normal.  
Connection with nMEa 2000  
Device Lost—the GMI 10 has lost  
connection with a NMEA 2000  
device.  
GMI 10 Quick Start Manual  
1ꢃ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
unable to Claim nMEa 2000  
address—there is a conflict  
between NMEA 2000 devices on  
the NMEA 2000 network.  
Contact Garmin  
Contact Garmin Product Support  
if you have any questions while  
using your GMI 10. In the USA,  
contact Garmin USA by phone at  
(913) 397-8200 or (800) 800-1020.  
Water Speed Sensor Is not  
Working—water speed calibration  
error – recalibrate the speed sensor.  
In the UK, contact Garmin (Europe)  
Ltd. by phone at 0808 2380000.  
In Europe, go to www.garmin.com/  
support and click Contact Support  
for in-country support information,  
or contact Garmin (Europe) Ltd. by  
phone at +44 (0) 870.8501241.  
1ꢄ  
GMI 10 Quick Start Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2009 Garmin Ltd. or its subsidiaries  
Garmin International, Inc.  
1200 East 151st Street, Olathe, Kansas 66062, USA  
Garmin (Europe) Ltd.  
Liberty House, Hounsdown Business Park, Southampton, Hampshire,  
SO40 9LR UK  
Garmin Corporation  
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan  
October 2009  
Part Number 190-01015-01 Rev. C  
Printed in Taiwan  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eiki Projector LC SX4 User Manual
Escort Radar Detector 75 Detector User Manual
Fender Stereo Amplifier Super Champ X2 User Manual
Fisher Price Fitness Equipment J5970 User Manual
Fundex Games Games 2475 User Manual
Garland Microwave Oven EN S85M User Manual
Gemini Car Speaker MS USB User Manual
GE Oven JKP17 User Manual
Global Machinery Company Cordless Saw RC1200 User Manual
Glowworm Lighting Boiler CXI User Manual