INSTALLATION INSTRUCTIONS
Product
Revision
Form
Docking Staton - Getac B300 USB 3.0
INST-626
Rev.A
7160-0526-00 No RF
7160-0526-02 Dual RF
Printing Spec: PS-001
7160-0526-00 & 7160-0526-02 Docking
Stations are only compatibile with 3rd, 4th
& 5th generation Getac B300 computers.
Computers can be identified by the p/n
found on the bottom.
3rd generation (B300-H) 52628417xxxx,
4th generation (B300-G4) 52628540xxxx,
5th generation (B300-G5) 52628591xxxx.
1st generation 52628144xxxx &
2nd generation (B300-X) 52628317xxxx
computers are not compatible.
*These instructions are for the docking station only. For instructions on features, set-up
and operation of the B300 computer, please refer to the manuals provided by Getac with
the computer.
**This docking station is designed to be used with a variety of Gamber-Johnson mounting
systems. Installation instructions for other Gamber-Johnson products are provided with
each individual product.
IMPORTANT SAFETY INFORMATION for
INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding
of automotive electrical procedures and systems, along with proficiency in the installation
and service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the
docking station.Opening the power/port replication housing will void the product
warranty.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2014 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Page 1 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
During Installation
•
DO NOT connect this docking station to the vehicle battery until:
1. ALL other electrical connections are made
2. Mounting of ALL components are complete
3. VERIFICATION that no shorts exist in the entire system
•
•
DO NOT install equipment or route wiring or cords in the deployment path of any
air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are
clear of anything that could be damaged.
CAUTION: If wiring is shorted to the frame, high current conductors can cause
hazardous sparks resulting in electrical fires or flying molten metal.
After Installation
Test the docking station to ensure that it is working properly.
•
File these instructions in a safe place and refer to them when performing
maintenance or re-installing.
WARNING: Failure to follow all safety precautions and instructions may result
in property damage, serious injury or death.
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify that all electronic
and software issues are resolved prior to installation:
1. Make sure computer is operational by itself.
2. Insert computer into docking station and verify that the computer is operating in the
dock.
3. Interconnect entire assembly and verify start-up of all components, including other
equipment (printers, modems, scanners, etc.).
*Gamber-Johnson also recommends positioning of all mounts and equipment in the vehicle
prior to the actual install to verify that mounting locations are safe and practical.
Page 3 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SWITCH
This docking station has a power switch with an LED light (see Figure 1):
•
"INPUT POWER" - The green LED light, built into the power switch, indicates that there is
power to the unit.
•
Standard Installation - In this set-up, the power switch can be turned on and
off to regulate power through the unit.
•
By-Pass Installation - In this set-up, the unit is continuously powered
(bypassing the power switch) and the green LED light is lit regardless of
switch position.
*Refer to the Power Supply and Wiring Instructions sections of this manual for further
information regarding these features.
Red, Black &
Blue Wires w/
Disconnect
Figure 1
Power Switch w/
Green "POWER" LED
POWER SUPPLY INFORMATION
This docking station has a built-in power supply and is designed to be used with an 11 - 28
volt DC system. The voltage output is factory set at 19 volts.
Power is provided using the wires located on the underside of the docking station:
•
Standard Installation - Use the RED and BLACK wires to utilize the power
switch on the docking station, regulating power through the unit.
By-Pass Installation - Use the BLUE and BLACK wires to continuously power the
docking station and bypass the power switch.
•
Page 4 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING INSTRUCTIONS
IMPORTANT: Make sure that you have read this entire section before you begin wiring!
Refer to Figure 2
1. Install docking station into vehicle, making sure that all bolts are tight.
2. Attach BLACK ground wire to the location where the vehicle battery grounds to
vehicle chassis.
a. Standard Installation (Power switch is operational) - Connect the RED wire to the
supply voltage (V+) from the vehicle. (The BLUE wire remains unconnected)
b. By-Pass Installation (Power switch is by-passed) - Connect the BLUE wire to the
supply voltage (V+) from the vehicle. (The RED wire remains unconnected)
IMPORTANT REMINDERS:
•
•
Use only SAE J1128 Type GPT number 14 AWG stranded wire (minimum) to attach the
docking station to the vehicle's electrical system.
Connect lead wires to the disconnect pigtail using the butt splice connectors provided with the
docking station.Caution: The butt splice connections must be made as close
to the docking station as possible using the disconnect pigtail provided with the docking
station. The disconnect must be easily accesible. When assembling the butt splice connectors
,
CT-1550 OR CT-1551.
use only Panduit crimp tools CT-100, CT-600, CT-1525
Using thewire joint provided with the docking station,cap the un-used RED or BLUE wire on
the disconnect pigtail.Use only Panduit crimp tool CT-1550 or CT-1551.
must not exceed 30 feet and
•
•
Route the lead wires to the battery. Total wire in the circuit
must conform to SAE standard J1128.
Protect the lead wires from abrasion and chafing by using wire loom or conduit, and route
away from moving parts or areas where high temperatures may occur.
•
•
Connection of the supply voltage (V+) must be kept as close to the battery as possible.
The power connection must be made with the 10 amp in-line fuse and fuse holder provided
with the dock. Connect the fuse holder to the lead wire using the butt splice connectors
provided with fuse holder.When assembling the butt splice connectors use only Panduit
crimp tools CT-100, CT-600, CT-1525 or CT-1551.
The fuse holder location must be kept within 10 inches of the connection to the
battery positive, away from moving parts, and temperatures that exceed 180 degrees F.
Caution: If the fuse holder requires replacement it should be replaced by qualified service
personnel using Littlefuse part number FHM1 (Gamber-Johnson part number 11689). This
device conforms to ASTM standard D471 and SAE standard J1128.
•
Fuse must be inserted in supplied fuse holder.Caution: For continued protection against risk
of fire replace only with the same type and rating of supplied fuse. The provided fuse is
rated at 10 amp, 32 volt AC/DC fast acting.
•
•
If a timing device is used follow the instructions of the manufacturer of that device. It must
be wired in-line with the supply voltage (V+) to the docking station.
If you have any installation questions, please call Gamber-Johnson customer support at
1-800-456-6868
Page 5 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2
Ground to Vehicle Chassis
14 AWG (black wire) J1128 TYPE GPT
Panduit #BSN14-C
Butt Splice connects to
black lead from dock
Panduit #BSN14-C
Butt Splice connects to
red or blue lead from dock
10"
Fuse
-
+
Vehicle Battery
14 AWG (red wire) J1128 TYPE GPT
Connect in-line fuse holder to lead
wire using Panduit #BSN14-C
Butt Splice connectors
CABLE RESTRAINT INFORMATION
Attach the supplied cable tie anchors to the
underside of the dock by pushing into the holes in
the locations shown (Figure 3).
Attach cable ties to the anchors as shown (Figure 3).
Retain the USB and Ethernet cables at the Support
Bracket using the supplied cable ties (Figure 3). If
the USB or Ethernet cables do not fit with the
Support Bracket, remove the bracket and restrain
the cables with the additional tie wrap anchors
supplied in the hardware bag.
USB/Ethernet
Support Bra c ket
Figure 3
Assemble c a ble ties to the
a nc hors a nd route c a bles
a s required
Page 6of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
DOCKING THE COMPUTER
1. Make sure the sliding door (located on the
on the back of the computer) has
been fully opened, exposing the computer's
docking connector. (Figure 4)
2. Set computer in the dock:
a. Hook the front of the computer on the front
retainer (Figure 5).
b. Lower the back of the computer
onto the Alignment Pins (Figure 5).
c. Lightly press down on the back of the computer
to ensure it is fully seated.
Sliding Door
Doc king C onnec tor
Figure 4
3. Pull the docking handle towards the front of the
dock until the latch catches (Figure 6).
(The Push Button latch can be locked for
added security)
Figure 5
4. Boot the computer. If the dock is powered, the
computer is powered and ready for use.
Doc king Ha ndle
in "Undoc ked"
position
*Docking station will operate with computer screen
opened or closed.
Front Reta iner
Doc king Ha ndle
Figure 6
in "Doc ked"
position
REMOVING COMPUTER FROM THE DOCK
1. Unlock with key if locked. Push button in until lever releases.
2. Lift the back of the computer off of the locating pins.
3. Lift the computer out from under the Front Retainer.
Page 7 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING on COMPUTER BATTERY POWER
Standard Installation (Power switch is operational) - If the DOCKING STATION power
switch is turned off, removing power from the vehicle battery, the Green Switch LED will
go out.
When the Green Switch LED is off , this indicates that the docking station is being
powered by only the computer's battery. This feature allows for the docking station:
1. To be used for a limited time, depending on the computer's battery life.
2. To serve as a reminder to turn off the computer's power switch.
TROUBLESHOOTING
"Power" GREEN LED light does not light up:
If after applying power to the docking station and turning the power switch on, the GREEN
LED light does not light up:
1. Check to see if the BLACK and RED (or BLUE in by-pass installation) wires are
providing power to the docking station.
a. If NO - Determine the cause and solve.
b. If YES - The problem is inside the docking station and should not be
adjusted by the installer. Please call Gamber-Johnson customer
support at 1-800-456-6868.
CAUTION: The docking connector has been designed to include "float" which allows for
slight misalignment with the computer connector. The action of engaging the docking
connector should be free and smooth.Do not force the connectors to engage. You may
damage the connector or the computer.
Page 8 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|