Installation
Instructions
Advantium® 240V
Built-In SpeedCook
Ovens
PSB2200
PSB2201
ZSC2200
ZSC2201
ZSC2202
49-40574-1
MFL06213302
02-08 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
Design Information
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
21-1/2”
29-3/4”
19”
1”
13”
ADVANCE PLANNING
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
ꢀ #2 Phillips screwdriver
• These ovens may be installed directly into a 30” wide
oven cabinet.
• Cutout dimensions are NOT the same for installation
with or without an accessory storage drawer. Make
sure to use the correct cutout when preparing the
opening.
NOTE: Model ZSC2202 CANNOT be installed with an
accessory storage drawer. See Installation
Preparation Without an Accessory Storage Drawer
for this model.
ꢀ Hand held drill
ꢀ High speed drill bit, 3/32″ diameter
ꢀ 3/8″ slot head screwdriver
ꢀ Level
ꢀ Saw
ꢀ 2x4 or 2x2 lumber for installing runners
or 3/8″ plywood for floor (if required)
ꢀ Wood screws or other hardware for installing
runner or shelf to support oven (if required)
ꢀ Safety glasses or goggles
IMPORTANT — This oven is not approved for
use above another built-in Advantium Speedcook
oven, a side by side installation or below a
countertop.
•
For personal safety, this oven cannot be installed
in a cabinet arrangement such as an island or
peninsula.
PARTS SUPPLIED
ꢀ 6 brass screws (3 required, 3 extra)
ꢀ 5 color matched screws (4 required, 1 extra)
ꢀ Bottom trim
• The oven must be installed at least 36-3/4" above
the floor.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
• Cabinets installed adjacent to wall ovens must
have an adhesion spec of at least 194ºF
temperature rating.
The oven must be securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone to
climb, sit, stand or hang on the oven door.
ELECTRICAL TOOLS AND PARTS
REQUIRED (NOT SUPPLIED)
ꢀ Junction box
ꢀ Electrical cable (3-conductor or 4-conductor wire
as required by local codes)
ꢀ UL-listed conduit connectors
ꢀ Wire cutters and wire strippers
If installing the drawer accessory, the drawer must
be assembled to the oven prior to installation into
the cabinet. See the Accessory Storage Drawer
Assembly Instructions.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
ELECTRICAL REQUIREMENTS
Single Speedcook Installation
INSTALL JUNCTION BOX
The conduit is located at the top right on the back of
the oven.
Product rating is 120/208 or 120/240 volt, 60 Hz,
30 amps. This product must be connected to a supply
circuit of the proper voltage and frequency and
protected by a time delay fuse or circuit breaker.
Power should be supplied from a separate, dedicated
30-ampere branch circuit. Wire size must conform to
the requirements of the National Electrical Code or the
prevailing local code.
Locate and install the junction box within reach of the
oven conduit.
• Through the left or right sides of the cabinet wall
and into adjacent cabinet.
• Or, through the cutout floor.
• Or, in the upper cabinet.
Combined Speedcook and Wall Oven Installation
When installed in combination with a GE/Monogram
single wall oven, use separate electrical junction boxes.
Refer to single oven installation instructions for
electrical requirements of that product.
Cutout
Height
These connections must be made by a qualified
electrician. All electrical connections must meet
National Electrical Code or prevailing local codes.
Combined Speedcook and Warming Drawer
Installation
When installing the Speedcook oven over a GE or
Monogram electric warming drawer, a separate 120V,
60Hz, properly grounded receptacle must be installed.
See instructions packed with the warming drawer.
WARNING
•
The electrical power to the oven branch circuit
must be shut off while line connections are being
made.
•
•
Use copper wiring only.
Electrical ground is required on this appliance.
The free end of the green wire (ground wire)
must be connected to a suitable ground.
This wire must remain grounded to the oven.
•
If cold water pipe is interrupted by plastic,
non-metallic gaskets, union connections or other
insulating materials, DO NOT use for grounding.
•
•
DO NOT ground to a gas pipe.
DO NOT have a fuse in the NEUTRAL or
GROUNDING circuit. A fuse in the NEUTRAL or
GROUNDING circuit could result in an electrical
shock.
•
Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
Failure to follow these instructions could result in
serious injury or death.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING
PREPARE THE OPENING (CONT.)
The Advantium 240V can be installed in
combination with other GE/Monogram appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Installation over a GE/Monogram
Warming Drawer:
23-1/2”
Construct
30”
Solid Bottom
Min. 3/8”
Single Advantium 240V Installation:
Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
25-1/4”
23-1/2”
30”
2” Min.
(3” recommended)
17-1/2”
25-1/4”
Per warming
drawer
requirement
17-1/2”
36-3/4”
Min.
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
36-3/4”
Min.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.
• Always maintain 36-3/4” minimum height from
the floor to the cutout in any single or combined
installation.
• Allow 2-1/8” case trim overlap on the sides and
7/8” overlap on the bottom of the opening for all
models. Allow 1-1/4” case trim overlap on the top
for models PSB2200 and PSB2201 and 3/4”
overlap on the top for models ZSC2200, ZSC2201
and ZSC2202.
• Oven overlaps will conceal cut edges on all sides
of the opening.
When installed over a single oven or a warming
drawer, allow at least 2” between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 240V and the other
appliance overlaps.
Construct a solid oven floor of 3/8” min. thick plywood
supported by 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram Oven:
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram Oven and
Warming Drawer:
23-1/2”
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
30”
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
30”
23-1/2”
Runners all
Runners all
Four Sides
25-1/4”
Four Sides
25-1/4”
17-1/2”
2” Min.
(3” recommended)
2” Min.
17-1/2”
(3” recommended)
Per Oven
Requirement
Per Oven
Requirement
45-1/4”
Min.
45-1/4”
Min.
2” Min.
Per warming drawer requirement
• If you are replacing a GE/Monogram electric
double oven with the combined installation of
an Advantium 240V and a single oven, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2” minimum shown.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight of
this approximate 80-pound oven, plus additional
oven loads of up to 50 pounds or a total weight
of 130 pounds.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION
WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING
PREPARE THE OPENING (CONT.)
The Advantium 240V can be installed in
combination with other GE/Monogram appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Single Advantium 240V Installation (cont.)
When installed over a single oven or a warming
drawer, allow at least 2” between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 240V and the other
appliance overlaps.
Single Advantium 240V Installation:
Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
Construct a solid oven floor of 3/8” min. thick plywood
supported by 2 x 4 or 2 x 2 runners on all sides.
23-1/2”
30”
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
25-1/4”
Min.*
Installation over a GE/Monogram
Warming Drawer:
23-1/2”
Construct
30”
Solid Bottom
Min. 3/8”
21”
Plywood
Construct
Base
Supported
by 2x4 or 2x2
Runners all
Four Sides
25-1/4”
Min.*
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
36-3/4”
Min.
2” Min.
(3” recommended)
21”
Per warming
drawer
requirement
* For existing cutouts, a maximum width of 28-1/2”
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
36-3/4”
Min.
• Always maintain 36-3/4” minimum height from
the floor to the cutout in any single or combined
installation.
* For existing cutouts, a maximum width of 28-1/2”
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
• Allow 3/4” to 2-1/8” case trim overlap on the sides
and 7/8” overlap on the bottom of the opening for
all models. The amount of overlap on the sides
depends on the actual cutout width. Allow 1-1/4”
case trim overlap on the top for models PSB2200
and PSB2201 and 3/4” overlap on the top for
models ZSC2200, ZSC2201 and ZSC2202.
• Oven overlaps will conceal cut edges on all sides
of the opening.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION
WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING (CONT.)
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram Oven:
Installation over a GE/Monogram Oven and
Warming Drawer:
23-1/2”
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
30”
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
30”
23-1/2”
25-1/4”
Min.*
Runners all
Four Sides
25-1/4”
Min.*
21”
2” Min.
(3” recommended)
2” Min.
21”
(3” recommended)
Per Oven
Requirement
Per Oven
Requirement
45-1/4”
Min.
2” Min.
45-1/4”
Min.
Per warming drawer requirement
* For existing cutouts, a maximum width of 28-1/2”
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
• If you are replacing a GE/Monogram electric
double oven with the combined installation of
an Advantium 240V and a single oven, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2” minimum shown.
* For existing cutouts, a maximum width of 28-1/2”
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the cabinet
load, in addition to the added weight of this
approximate 80-pound oven and 30-pound
drawer, plus additional oven loads of up to 50
pounds or a total weight of 160 pounds.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
1 REMOVE THE PACKAGING AND PARTS
• Remove all packing material and tape.
• Locate parts package containing mounting screws.
• Remove the oven from the carton. Do not lift unit by
handle or conduit. Two people are required to lift
this oven.
• Open the door and remove any packaging in oven.
Owner’s
Manual
Rack
Installation
Instructions
Owner’s Manual
Bottom Trim
Cooking
Guide
5 Color Matched Screws
(4 required, 1 extra)
6 Brass Screws
(3 required, 3 extra)
Cook Book
Glass Tray
Cooking Guide
Turntable Ring
IMPORTANT: If installing the Advantium 240V Oven
with an accessory storage drawer, read the storage
drawer assembly instructions to assemble the
products together before proceeding to Step 2.
Metal Trays (2)
Metal Grill Tray
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
2 ROUTE CONDUIT THROUGH
2 ROUTE CONDUIT THROUGH
CUTOUT
CUTOUT (CONT.)
When connecting to a 3-conductor branch
circuit:
• Connect oven red lead to branch circuit red lead.
• Connect oven black lead to branch circuit black
lead.
CAUTION:
Two people are required to lift
the oven into the opening. Grasp the bottom at
front and rear. Discard foam base. DO NOT USE
HANDLE OR CONDUIT TO LIFT THE OVEN. DAMAGE
WILL OCCUR.
• Connect oven green ground lead and white lead
to branch circuit neutral (white or gray).
With oven in front of the cabinet opening:
• Insert conduit into cabinet opening. Connect oven
wiring and branch circuit.
• Lift the oven into the opening while continuing to feed
the conduit in the direction of the installed junction
box. Be sure the conduit does not get pinched
between the back of the oven and the cabinet wall.
• Leave oven a few inches forward of the cabinet
front frame. Do not push the unit all of the way
into the cutout.
When connecting to a 4-conductor branch
circuit:
• Connect oven red lead to branch circuit red lead.
• Connect oven black lead to branch circuit black
lead.
• Break connection between oven white lead and
oven green ground lead.
• Connect oven white lead to branch circuit neutral
lead (white or gray).
• Connect oven green ground lead to branch circuit
ground lead (green or bare copper).
(Oven shown without
accessory storage drawer.)
WARNING
• Disconnect power to the junction box before
making the electrical connection.
• Electrical ground is required on this appliance.
• Do not connect the electrical supply until
appliance is permanently grounded.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded,
metallic, permanent wiring system, or an equipment
grounding connector should be run with the circuit
conductors and connected to the equipment
grounding terminal or lead on the appliance.
Failure to follow these instructions could result
in fire, personal injury or electrical shock.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
4 INSTALL MOUNTING SCREWS
3 INSTALL BOTTOM TRIM
NOTE: If installing the Advantium 240 Oven with an
accessory storage drawer, the bottom trim is not
required. Proceed to Step 4.
• Align bottom trim tabs to slots in the bottom of the
oven.
• Slide the oven the remaining way into the opening
so that the side flanges and control panel are
against the cabinet frame. Make sure that the oven
is centered in the opening.
• Secure the bottom trim to the bottom of the oven
using 3 brass screws provided.
• Open the door, place a turntable tray in the oven
and make sure that the tray in the unit is level.
• Drill pilot holes through the side flanges.
• Drive the color matched screws into the side
flanges. It is recommended that the screws
be hand tightened.
If installing oven with an accessory storage
drawer:
• Open the drawer.
• Drill pilot holes through the side flanges.
• Drive color match screws into the side flanges.
It is recommended that the screws be hand
tightened.
5 FINALIZE INSTALLATION
• Turn power on at the source. The interior light
should come on when the door is opened.
• Refer to Owner’s Manual for operating instructions.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Advantium® 240V Built-In Accessory Storage Drawer
JX2200, JX2201, ZX2201
MODELS AVAILABLE
BEFORE YOU BEGIN
Profile Models:
Read these instructions completely and carefully. Read
JX2200BB–Black
the Installation Instructions for the Advantium 240V oven
completely and carefully for cutout dimensions and
step-by-step instructions.
JX2201SS–Stainless Steel
Monogram Models:
IMPORTANT — Save these instructions for
ZX2201SS–Stainless Steel
local inspector’s use.
NOTE: Advantium 240V Built-In SpeedCook Oven
model ZSC2202SS CANNOT be installed with an
accessory storage drawer. See Installation
Preparation Without an Accessory Storage Drawer in
the Advantium 240V Built-In SpeedCook Oven
Installation Instructions for this model.
IMPORTANT — Observe all governing codes
and ordinances.
• NOTE TO INSTALLER: Be sure to leave these
instructions with the Consumer.
• NOTE TO CONSUMER: Keep these instructions with
your Advantium 240V Oven Owner’s Manual for
future reference.
• SKILL LEVEL: Installation of this appliance requires
basic mechanical skills.
PRODUCT DIMENSIONS AND CLEARANCES
• COMPLETION TIME: One hour with the installation
of an Advantium 240V oven.
5”
• Proper installation is the responsibility of the installer.
Allow 15” clearance
when fully open
• Product failure due to improper installation is not
covered under the Warranty. See the Advantium
240V Oven Owner’s Manual for warranty information.
NOTE: Appearance will vary by model.
TOOLS REQUIRED
• #2 Phillips screwdriver
PARTS SUPPLIED
• 2 Side Supports
• Screws
• Screws (color matched)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY TO ADVANTIUM 240V BUILT-IN SPEEDCOOK OVEN
ASSEMBLING THE OVEN TO DRAWER
(CONT.)
1 REMOVE PACKAGING AND PARTS
• Remove the drawer from the carton.
• Remove all packing material and tape.
• Open the drawer and remove any parts inside.
• Locate parts.
Remove the front two bottom screws on each
side of the oven and the top center screw on
each side of the storage drawer.
C
Side Supports (2)
Assembly
Instructions
Screws (2 Sets)
2 ASSEMBLING THE OVEN TO DRAWER
Place storage drawer on a surface with the
front of drawer hanging over the edge of the
surface. Not placing the front edge of drawer
over the edge of the surface may result in
damage to the drawer since the front edge of
drawer hangs below the bottom of drawer.
A
Place the side supports into the tabs on the
drawer and secure using the screws supplied
and the screws removed in Step C.
D
Place the oven on top of the storage drawer.
Make sure that the back and sides of the oven
align with the back and sides of drawer.
B
The oven and storage drawer assembly is now
ready to be installed. Return to the Advantium
240V Built-In SpeedCook Oven Installation
Instructions to complete the installation.
E
NOTE: The bottom of the oven side flanges will
sit directly in front of the top of the storage
drawer side flanges.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
NOTE: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
Printed in Korea
Download from Www.Somanuals.com. All Manuals Search And Download.
|