GE Oven PSB1200BB User Manual

Installation  
Instructions  
Advantium® 120V  
Built-In SpeedCook  
Ovens  
PSB1200  
PSB1201  
ZSC1201  
ZSC1202  
For a Spanish version of this manual, visit our Website at ge.com.  
Para consultar una version en español de este manual de instrucciones,  
visite nuestro sitiode internet ge.com.  
49-40593-1  
MFL59060901  
12-08 JR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Information  
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.  
21-1/2″  
29-3/4″  
1-1/8″  
19
13/16″  
5/8″  
13″  
ADVANCE PLANNING  
TOOLS AND PARTS REQUIRED  
(NOT SUPPLIED)  
#2 Phillips screwdriver  
• Hand-held drill  
High speed drill bit, 3/32diameter  
3/8slot-head screwdriver  
Level  
These ovens may be installed directly into a 30wide  
oven cabinet.  
Cutout dimensions are NOT the same for installation  
with or without an accessory storage drawer.  
Make sure to use the correct cutout when preparing  
the opening.  
NOTE: ZSC1202 models CANNOT be installed  
with an accessory storage drawer. See Installation  
Preparation Without an Accessory Storage Drawer  
for this model.  
Saw  
2 x 4 or 2 x 2 lumber for installing runners  
or 3/8plywood for floor (if required)  
Wood screws or other hardware for installing  
• Allow for clearance to adjacent corners, walls,  
drawers, etc.  
runner or shelf to support oven (if required)  
Safety glasses or goggles  
The oven must be securely installed in a cabinet  
that is firmly attached to the house structure.  
Weight on the oven door could cause the oven  
to tip and result in injury. Never allow anyone  
to climb, sit, stand or hang on the oven door.  
If installing the drawer accessory, the drawer must  
be assembled to the oven prior to installation into  
the cabinet. See the Accessory Storage Drawer  
Assembly Instructions.  
PARTS SUPPLIED  
6 screws (3 required, 3 extra)  
5 color-matched screws (4 required, 1 extra)  
Bottom trim (2)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
ELECTRICAL REQUIREMENTS  
Single Advantium 120 Installation:  
This product requires a 120-volt, 60 Hz, 15-amp circuit  
and draws 1.8 kilowatts. This product must be  
connected to a supply circuit of the proper voltage  
and frequency.  
• Wire size must conform to the requirements of the  
National Electrical Code or the prevailing local code  
for this kilowatt rating.  
• The power supply cord and plug should be brought  
to a separate 15 or 20 ampere branch circuit single  
grounded receptacle. The outlet box should be  
located within reach of the 48" power cord.  
IMPORTANT: (Please read carefully).  
ELECTRICAL LOCATION  
The power cord of this appliance is equipped with  
a three-prong (grounding) plug that mates with  
a standard three-prong grounding wall receptacle  
to minimize the possibility of electric shock. The  
customer should have the wall receptacle and  
circuit checked by a qualified electrician to make  
sure the receptacle is properly grounded and has  
the correct polarity.  
• Where a standard two-prong wall receptacle is  
encountered, it is the personal responsibility and  
obligation of the consumer to have it replaced with  
a properly grounded three-prong wall receptacle.  
6”  
9”  
Locate outlet box in the shaded area  
Do not, under any circumstances, cut or remove  
the third (ground) prong from the power cord.  
Install a recessed electrical outlet in the back wall  
of the opening within 6of either side and at least  
9above the cutout floor.  
DO NOT USE AN EXTENSION CORD.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITHOUT an Accessory Storage Drawer  
PREPARE THE OPENING  
PREPARE THE OPENING (cont.)  
The Advantium 120V can be installed in  
combination with other GE/Monogram appliances.  
Always follow each product’s Installation  
Instructions to complete the installation.  
Installation over a GE/Monogram  
Warming Drawer:  
30″  
23-1/2″  
Construct  
Single Advantium 120V Installation:  
Order a 30wide single oven cabinet or cut  
the opening in a wall to the dimensions shown.  
Solid Bottom  
Min. 3/8″  
Plywood  
Supported  
by 2 x 4 or 2 x 2  
Runners all  
Four Sides  
25-1/4″  
30″  
23-1/2″  
17-1/2″  
2Min.  
(3Recommended)  
25-1/4″  
Per Warming  
Drawer  
Requirement  
17-1/2″  
Construct  
Base  
Min. 3/8″  
Plywood  
Supported  
by 2 x 4 or  
2 x 2 Runners  
all Four Sides  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven supports  
above the Warming Drawer location do not obstruct  
the required interior depth and height. See Warming  
Drawer installation instructions for details.  
• Allow 2-1/8case trim overlap on the sides,  
1-1/16overlap on the top and 7/8overlap  
on the bottom of the opening for all models.  
• Oven overlaps will conceal cut edges on all sides  
of the opening.  
When installed over a single oven or a warming  
drawer, allow at least 2between the two openings.  
This separation will provide clearance for bottom  
overlap of the Advantium 120V and the other  
appliance overlaps.  
Construct a solid oven floor of 3/8min. thick plywood  
supported by 2 x 4 or 2 x 2 runners on all sides.  
• The support must be level and rigidly mounted,  
flush with the bottom edge of the cutout.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITHOUT an Accessory Storage Drawer  
PREPARE THE OPENING (cont.)  
PREPARE THE OPENING (cont.)  
Installation over a GE/Monogram oven:  
Installation over a GE/Monogram Oven and  
Warming Drawer:  
30″  
23-1/2″  
30″  
23-1/2″  
Construct Solid  
Bottom Min.  
3/8Plywood  
Supported by  
2 x 4 or 2 x 2  
Runners all  
Construct Solid  
Bottom Min.  
3/8Plywood  
Supported by  
2 x 4 or 2 x 2  
Runners all  
25-1/4″  
25-1/4″  
Four Sides  
Four Sides  
17-1/2″  
2Min.  
(3Recommended)  
17-1/2″  
2Min.  
(3Recommended)  
Per Oven  
Requirement  
Per Oven  
Requirement  
2Min.  
(3Recommended)  
Per Warming  
Drawer Requirement  
• If you are replacing a GE/Monogram electric  
double oven with the combined installation  
of an Advantium 120V and a single oven, use  
the dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 2minimum shown.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location  
do not obstruct the required interior depth  
and height. See Warming Drawer installation  
instructions for details.  
CAUTION:  
For personal safety, the  
mounting surface must be capable of supporting  
the cabinet load, in addition to the added weight  
of this approximate 80-pound oven, plus  
additional oven loads of up to 50 pounds  
or a total weight of 130 pounds.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITHOUT an Accessory Storage Drawer  
PREPARE THE OPENING (cont.)  
PREPARE THE OPENING (cont.)  
Installation over another GE/Monogram  
Installation under a GE/Monogram  
Microwave Oven and over a Warming  
Drawer:  
Under-the-Counter (UTC) oven:  
23-1/2″  
30″  
30″  
23-1/2″  
Construct Solid  
Bottom Min.  
3/8Plywood  
Supported by  
2 x 4 or 2 x 2  
Runners all  
Construct Solid  
Bottom Min.  
3/8Plywood  
Supported by  
2 x 4 or 2 x 2  
Runners all  
25-1/4″  
25-1/4″  
Four Sides  
Four Sides  
17-1/2″  
2Min.  
(3Recommended)  
Per Oven  
3.5Min.  
(4.5Recommended)  
Requirement  
17-1/2″  
17-1/2″  
2Min.  
(3Recommended)  
Per Warming  
Drawer Requirement  
• If you are mounting an Under-the-Counter  
GE/Monogram oven over another, use the  
dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 2minimum shown.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location  
do not obstruct the required interior depth  
and height. See Warming Drawer installation  
instructions for details.  
CAUTION:  
For personal safety, the  
mounting surface must be capable of supporting  
the cabinet load, in addition to the added weight  
of this approximate 80-pound oven, plus  
additional oven loads of up to 50 pounds  
or a total weight of 130 pounds.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITHOUT an Accessory Storage Drawer  
23-1/2″  
PREPARE THE OPENING (cont.)  
Installation beside another GE/Monogram  
Built-in Speedcook Oven:  
• If you are mounting one Under-the-Counter  
GE/Monogram oven beside the other, use the  
dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 4-1/2minimum shown.  
25-1/4″  
25-1/4″  
17-1/2″  
17-1/2″  
4-1/2Min.  
(5-1/2Recommended)  
PREPARE THE OPENING (cont.)  
Installation under a GE/Monogram 30or 36Cooktop or Countertop:  
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout  
size. See the label on top of the oven for approved cooktop models. This oven requires a separate, properly  
grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply. Use a 36″  
or wider base cabinet.  
1-1/2Min.  
25″  
Cooktop  
Cooktop  
36  
Countertop  
Height  
17-1/2  
25-1/4  
Cooktop height including depth  
of electrical box on some models.  
Refer to cooktop installation  
instructions.  
No minimum clearance required  
between cooktop and oven.  
23-1/2  
NOTE: The oven is only approved to be installed  
under the specific models as labeled on the unit.  
4High  
Toekick  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITH an Accessory Storage Drawer  
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4  
.  
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT  
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.  
PREPARE THE OPENING (cont.)  
PREPARE THE OPENING (cont.)  
The Advantium 120V can be installed in  
combination with other GE/Monogram appliances.  
Always follow each product’s Installation  
Instructions to complete the installation.  
Installation over a GE/Monogram  
Warming Drawer:  
23-1/2″  
30″  
Single Advantium 120V Installation:  
Order a 30wide single oven cabinet or cut  
the opening in a wall to the dimensions shown.  
Construct Solid  
Bottom Min. 3/8″  
Plywood Supported  
by 2 x 4 or 2 x 2  
25-1/4″  
Min.  
30″  
23-1/2″  
Runners all Four Sides  
21″  
2Min.  
(3Recommended)  
25-1/4″  
Min.  
Per Warming  
Drawer  
Requirement  
36-3/4″  
Min.*  
21″  
*Required for  
Construct Base  
Min. 3/8Plywood  
Supported by 2 x 4  
or 2 x 2 Runners  
all Four Sides  
Monogram models  
36-3/4″  
Min.*  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location  
do not obstruct the required interior depth  
and height. See Warming Drawer installation  
instructions for details.  
*Required for  
Monogram models  
• Allow 2-1/8case trim overlap on the sides,  
1-1/16overlap on the top and 7/8overlap  
on the bottom of the opening for all models.  
• Oven overlaps will conceal cut edges on all sides  
of the opening.  
When installed over a single oven or a warming  
drawer, allow at least 2between the two openings.  
This separation will provide clearance for bottom  
overlap of the Advantium 120V and the other  
appliance overlaps.  
Construct a solid oven floor of 3/8min. thick plywood  
supported by 2 x 4 or 2 x 2 runners on all sides.  
• The support must be level and rigidly mounted,  
flush with the bottom edge of the cutout.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITH an Accessory Storage Drawer  
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4  
.  
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT  
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.  
PREPARE THE OPENING (cont.)  
PREPARE THE OPENING (cont.)  
Installation over a GE/Monogram Oven:  
Installation over a GE/Monogram Oven and  
Warming Drawer:  
30″  
23-1/2″  
30″  
23-1/2″  
Construct Solid  
Bottom Min.  
3/8Plywood  
Supported by  
2 x 4 or 2 x 2  
Runners all  
Construct Solid  
Bottom Min.  
3/8Plywood  
Supported by  
2 x 4 or 2 x 2  
Runners all  
25-1/4″  
Min.*  
25-1/4″  
Min.*  
Four Sides  
Four Sides  
21″  
2Min.  
(3Recommended)  
21″  
2Min.  
(3Recommended)  
Per Oven  
Requirement  
Per Oven  
Requirement  
36-3/4″  
Min.  
45-1/4″  
45-1/4″  
2Min.  
(3Recommended)  
Recommended*  
*Required for  
Monogram models  
Per Warming  
Drawer Requirement  
* For existing cutouts, a maximum width of 28-1/2″  
is acceptable. If the opening is slightly wider,  
secure a furring strip on each side of the cutout  
for securing the oven.  
• If you are replacing a GE/Monogram electric  
double oven with the combined installation  
of an Advantium 120V and a single oven, use  
the dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 2minimum shown.  
* For existing cutouts, a maximum width of 28-1/2″  
is acceptable. If the opening is slightly wider,  
secure a furring strip on each side of the cutout  
for securing the oven.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location  
do not obstruct the required interior depth  
and height. See Warming Drawer installation  
instructions for details.  
CAUTION:  
For personal safety, the  
mounting surface must be capable of supporting  
the cabinet load, in addition to the added weight  
of this approximate 80-pound oven and 30-pound  
drawer, plus additional oven loads of up to  
50 pounds or a total weight of 160 pounds.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITH an Accessory Storage Drawer  
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4  
.  
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT  
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.  
PREPARE THE OPENING (cont.)  
PREPARE THE OPENING (cont.)  
Installation over another GE/Monogram  
Installation under a GE/Monogram  
Microwave Oven and over a Warming  
Drawer:  
Under-the-Counter (UTC) oven:  
30″  
23-1/2″  
23-1/2″  
30″  
Construct Solid  
Bottom Min.  
3/8Plywood  
Supported by  
2 x 4 or 2 x 2  
Runners all  
Construct Solid  
Bottom Min. 3/8″  
Plywood Supported  
by 2 x 4 or 2 x 2  
Runners all Four  
Sides  
25-1/4″  
25-1/4″  
Four Sides  
21″  
2Min.  
(3Recommended)  
Per Oven  
Requirement  
3.5Min.  
(4.5Recommended)  
21*  
21*  
2Min.  
*Profile models only  
(3Recommended)  
Per Warming  
Drawer Requirement  
*Profile models only  
• If you are mounting an Under-the-Counter  
GE/Monogram oven over another, use the  
dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 2minimum shown.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location  
do not obstruct the required interior depth  
and height. See Warming Drawer installation  
instructions for details.  
CAUTION:  
For personal safety, the  
mounting surface must be capable of supporting  
the cabinet load, in addition to the added weight  
of this approximate 80-pound oven, plus  
additional oven loads of up to 50 pounds  
or a total weight of 130 pounds.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Preparation WITH an Accessory Storage Drawer  
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4  
.  
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT  
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.  
23-1/2″  
PREPARE THE OPENING (cont.)  
Installation beside another GE/Monogram  
Built-in Speedcook Oven:  
• If you are mounting one Under-the-Counter  
GE/Monogram oven beside the other, use  
the dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 4-1/2minimum shown.  
25-1/4″  
25-1/4″  
21″  
21″  
4-1/2Min.  
(5-1/2Recommended)  
PREPARE THE OPENING (cont.)  
Installation under a GE Profile 30or 36Cooktop or Countertop:  
Gas or electric cooktops may be installed  
over this oven. See cooktop installation  
1-1/2Min.  
25″  
Cooktop  
instructions for the cutout size. See the  
label on top of the oven for approved  
cooktop models. This oven requires  
a separate, properly  
Cooktop  
36  
grounded 15-Amp,  
Countertop  
Height  
120-Volt, 60Hz power  
supply. The cooktop  
requires a separate power  
supply. Use a 36or wider  
base cabinet.  
IMPORTANT:  
For Profile models only.  
The Monogram oven  
and drawer combination  
cannot be installed below  
a countertop.  
21  
25-1/4  
Cooktop height including depth  
of electrical box on some models.  
Refer to cooktop installation  
instructions.  
No minimum clearance required  
between cooktop and oven.  
23-1/2  
NOTE: The oven is only approved to be installed  
under the specific models as labeled on the unit.  
4High  
Toekick  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
1 REMOVE THE PACKAGING AND PARTS  
• Remove all packing material and tape.  
• Locate parts package containing mounting screws.  
• Remove the oven from the carton. Do not lift unit  
by handle or conduit. Two people are required to lift  
this oven.  
• Open the door and remove any packaging in oven.  
Rack  
CAUTION:  
If installing the Advantium  
Owner’s  
Manual  
120V Oven below 36, you must use the plastic  
bottom trim due to burn risk to children. The  
plastic trim acts as insulation and will help  
prevent burns to children from hot surfaces.  
Installation  
Instructions  
Owner’s Manual  
Bottom Trim – Plastic  
Bottom Trim – Metal  
Cooking  
Guide  
Cook Book  
Glass Tray  
Cooking Guide  
Turntable Ring  
5 Color-Matched Screws  
(4 required, 1 extra)  
6 Brass Screws  
(3 required, 3 extra)  
IMPORTANT: If installing the Advantium 120V Oven  
with an accessory storage drawer, read the storage  
drawer assembly instructions to assemble the  
products together before proceeding to Step 2.  
Metal Trays (2)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
2 DOOR TRIM REMOVAL FOR ABOVE  
3 SLIDE THE OVEN INTO THE CUTOUT  
36INSTALLATION ONLY  
CAUTION:  
Two people are required to  
If installing the Advantium 120V Oven above 36″  
from the floor, you may remove the plastic trim  
from the bottom of the door for esthetic purposes  
if desired.  
lift the oven into the opening. Grasp the bottom  
at front and rear. DO NOT USE THE HANDLE TO LIFT  
THE OVEN. DAMAGE WILL OCCUR.  
CAUTION:  
If installing the Advantium  
120V Oven below 36, do not remove the  
plastic door trim due to burn risk to children.  
The plastic trim acts as insulation and will help  
prevent burns to children from hot surfaces.  
If installing above 36, remove the 3 screws that  
secure the plastic trim to the bottom of the door.  
Discard plastic trim. Replace screws.  
• Lift and hold the oven at the front of the opening.  
Hold the oven at an angle and plug in the power  
cord.  
• Carefully, slide the oven into the cabinet part  
way. Leave the oven a few inches forward of  
the cabinet frame.  
• Check to be sure the power cord is not trapped  
under the oven or along the sides of the oven.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
4 INSTALL BOTTOM TRIM  
6 INSTALL MOUNTING SCREWS  
CAUTION:  
If installing the Advantium  
120V Oven below 36, you must use the plastic  
bottom trim due to burn risk to children. The plastic  
trim acts as insulation and will help prevent burns  
to children from hot surfaces.  
NOTE: If installing the Advantium 120V Oven  
with an accessory storage drawer, the bottom trim  
is not required. Proceed to Step 5.  
• Installation Below 36, align trim tabs on the plastic  
trim to slots in the bottom of the oven.  
Slide the oven the remaining way into the opening  
so that the side flanges and control panel are  
against the cabinet frame. Make sure that the oven  
is centered in the opening.  
Open the door, place a turntable tray in the oven  
and make sure that the tray in the unit is level.  
Drill pilot holes through the side flanges.  
Plastic Trim  
Drive the color-matched screws into the side  
flanges. It is recommended that the screws  
be hand tightened.  
• Installation Above 36, align trim tabs on the plastic  
or metal trim to slots in the bottom of the oven.  
If installing oven with an accessory storage  
drawer:  
Open the drawer.  
Drill pilot holes through the side flanges.  
Plastic Trim  
OR  
Metal Trim  
Drive color-matched screws into the side flanges.  
It is recommended that the screws be hand  
tightened.  
Secure the bottom trim to the bottom of the oven  
using 3 screws provided.  
NOTE: If installing the Profile Advantium 120V Oven  
with an accessory storage drawer, you must use  
the Under-the-Counter (UTC) mounting bracket for  
the drawer.  
If installing the Monogram Advantium integrated  
model ZSC1201 above 36, the UTC mounting bracket  
for the accessory storage drawer must be used.  
5 INSTALL BOTTOM TRIM WITH  
ACCESSORY DRAWER  
If installing with an accessory drawer, see  
installation instructions on page 17 or instructions  
that come with the accessory drawer.  
7 FINALIZE INSTALLATION  
Turn power on at the source. The interior light  
should come on when the door is opened.  
Refer to Owner’s Manual for operating instructions.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GE Consumer & Industrial Appliances  
Assembly Instructions  
Advantium® Built-In Accessory Storage Drawer  
JX2200, JX2201, ZX2201  
MODELS AVAILABLE  
BEFORE YOU BEGIN  
Profile Models:  
Read these instructions completely and carefully. Read  
JX2200BB–Black  
the Installation Instructions for the Advantium 120V or  
240V oven completely and carefully for cutout  
dimensions and step-by-step instructions.  
JX2201SS–Stainless Steel  
Monogram Models:  
IMPORTANT Save these instructions for  
ZX2201SS–Stainless Steel (for installation above 36only)  
local inspector’s use.  
NOTE: Advantium 240V model ZSC2202SS and  
Advantium 120V model ZSC1202 CANNOT be  
installed with an accessory storage drawer. See  
Installation Preparation Without an Accessory Storage  
Drawer in the Installation Instructions for these models.  
IMPORTANT Observe all governing codes  
and ordinances.  
NOTE TO INSTALLER: Be sure to leave these  
instructions with the Consumer.  
NOTE TO CONSUMER: Keep these instructions with  
your Advantium 120V or 240V Oven Owner’s Manual  
for future reference.  
PRODUCT DIMENSIONS AND CLEARANCES  
SKILL LEVEL: Installation of this appliance requires  
basic mechanical skills.  
5″  
COMPLETION TIME: One hour with the installation  
of an Advantium 120V or 240V oven.  
Allow 15clearance  
when fully open  
Proper installation is the responsibility of the installer.  
Product failure due to improper installation is not  
covered under the Warranty. See the Advantium  
120V or 240V Oven Owner’s Manual for warranty  
information.  
NOTE: Appearance will vary by model.  
TOOLS REQUIRED  
• #2 Phillips screwdriver  
PARTS SUPPLIED  
• 2 Side Supports  
• Screws (8)  
• Screws (color-matched) (5)  
• Under-the-Counter Mounting Bracket (1)  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN  
1 REMOVE PACKAGING AND PARTS  
3 ASSEMBLING THE OVEN TO DRAWER  
Place storage drawer on a surface with  
the front of drawer hanging over the edge  
of the surface. Not placing the front edge  
of drawer over the edge of the surface may  
result in damage to the drawer since the front  
edge of drawer hangs below the bottom  
of drawer.  
A
• Remove the drawer from the carton.  
• Remove all packing material and tape.  
• Open the drawer and remove any parts inside.  
• Locate parts.  
Place the oven on top of the storage drawer.  
Make sure that the back and sides of the oven  
align with the back and sides of drawer.  
B
Side Supports (2)  
Assembly Instructions  
Under-the-Counter (UTC)  
Mounting Bracket  
Screws  
(6 required,  
2 extra)  
Color-Matched  
Screws  
(4 required,  
1 extra)  
NOTE: The bottom of the oven side flanges will  
sit directly in front of the top of the storage  
drawer side flanges.  
2 UNDER-THE-COUNTER (UTC)  
MOUNTING BRACKET INSTALLATION  
NOTE: For UTC models PSB1200, PSB1201 and  
ZSC1201 only.  
Open the accessory drawer so you have  
access to the top bracket.  
A
B
C
Remove the three screws securing the top  
bracket.  
Install the new UTC mounting bracket using  
the screws removed previously.  
Close the drawer and proceed with the  
installation.  
D
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN  
ASSEMBLING THE OVEN TO DRAWER  
(cont.)  
Remove the front two bottom screws on each  
side of the oven and the top center screw on  
each side of the storage drawer.  
C
Place the side supports into the tabs on the  
drawer and secure using the screws supplied  
and the screws removed in Step C.  
D
Side  
Support  
120v only  
The oven and storage drawer assembly is now  
ready to be installed. Return to the Advantium  
120V or 240V Built-In SpeedCook Oven  
Installation Instructions to complete  
the installation.  
E
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: While performing installations described in this book,  
safety glasses or goggles should be worn.  
GE Consumer & Industrial  
Appliances  
General Electric Company  
Louisville, KY 40225  
ge.com  
NOTE: Product improvement is a continuing endeavor at  
General Electric. Therefore, materials, appearance and  
specifications are subject to change without notice.  
Printed in Korea  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Trimmer SRM 2100SB User Manual
Edimax Technology Switch ES 5240G+ User Manual
Eton Clock Radio 4000 User Manual
Excalibur electronic Motorized Toy Car 641S User Manual
Extron electronic Stereo Receiver DVS 100 User Manual
Fisher Paykel Cooktop CG604 User Manual
Frymaster Electric Pressure Cooker 8BC User Manual
Garland Convection Oven MCO E 25 C User Manual
Gefen Network Card Component Audio to HDMI Adapter User Manual
GE Microwave Oven 164D3370P211 User Manual