BFLH70L, BFLH85L
Heater/Exhaust Fan/Light User’s Guide
e
Item Stock Number(s): BFLH70L, BFLH85L
IMPORTANT INSTRUCTIONS -
a
OPERATING MANUAL
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electric shock and injury to person, including the following:
1. Read all instructions before installing or using
exhaust fan.
accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
2. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
4. Installation work and electrical wiring must be done
by qualified person(s) in accordance with all applicable
codes and standards, including fire-related construction.
3. Before servicing or cleaning the unit, switch power
off at service panel and lock the service disconnecting 5. Sufficient air is needed for proper combustion and
means to prevent power from being switched on
exhausting of gases through the flue (chimney) of
SAVE THESE INSTRUCTIONS
210572111 Rev. B 5-06
1 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
ceiling. Secure the ends of the rails with screws or 1a. Mounting Tab Installation: Position housing against
nails (not included) to the joists and slide housing
the joist and trace an outline of the housing onto the
ceiling material (Figure 7). Set housing aside and
cut opening, being careful not to cut or damage any
electrical or other hidden utilities. Place housing
next to the joist and insure that it is flush with the
finished ceiling. Secure with screws or nails (not
provided) to the joists (Figure 5).
into final position (Figure 4).
Housing
Joist
Mounting Rails
Figure 4
1a. Mounting Tab Installation: Line up housing so that
it will be flush with the finished ceiling. Position the
fan so that the tabs rest flat against the joist and
secure with screws or nails (not provided) to ensure
proper installation (Figure 5).
Figure 7
SECTION 4
Ducting
CAUTION: ALL DUCTING MUST COMPLY WITH
LOCAL AND NATIONAL BUILDING CODES.
1. Remove any tape that might be holding the damper
in place during shipping and connect the ducting to
the fan’s duct collar (Figure 8). Secure in place using
tape or screw clamp. Always duct the fan to the
outside through a wall or roof cap.
Figure 5
SECTION 3
Existing Construction
1. Mounting Rail Installation: Set housing in position
between the joist and trace an outline onto the ceiling
material (Figure 6). Set housing aside and cut opening,
being careful not to cut or damage any electrical or
other hidden utilities. Install the rails on the housing
and position the housing in the previously cut hole so
that it is flush with the finished ceiling. Secure the
ends of the rails to the joists with screws or nails (not
provided) to ensure proper installation (Figure 4).
Figure 8
SECTION 5
Wiring
CAUTION: MAKE SURE POWER IS SWITCHED OFF
AT SERVICE PANEL BEFORE STARTING INSTALLATION.
WARNING: THIS UNIT MUST BE WIRED ON A
SEPARATE 20 AMP CIRCUIT.
CAUTION: ALL ELECTRICAL CONNECTIONS MUST
BE MADE IN ACCORDANCE WITH LOCAL CODES,
ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU
ARE UNFAMILIAR WITH METHODS OF INSTALLING
ELECTRICAL WIRING, SECURE THE SERVICES OF A
QUALIFIED ELECTRICIAN.
Figure 6
210572111 Rev. B 5-06
3 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Run wiring from approved wall switches carrying
the appropriate rating. One neutral (white), one
ground (green or bare copper), and three hot (black,
red, blue leads connected to the switch, one for
each function). Secure the electrical wires to the
housing with an approved electrical connector. Make
sure you leave enough wiring in the box to make the
connection to the fan’s receptacles.
SECTION 6
Completing the Installation
1. Insert the plug from the heating unit into the
receptacle marked “HEAT”, and the plug from the
fan into the receptacle marked “VENT”(Figure 11).
2. Connect the white wire from the house to the three
white wires from the fan. Connect one hot (black)
wire from the wall switch to the black wire from the
fan (this is the fan control). Connect second hot (red)
wire from the wall switch to the red wire from the
fan (this is the heat control). Connect the third hot
(blue) wire from the wall switch to the blue wire from
the fan (this is the light control). Connect the ground
wire from the house to the green wire from the fan
(Figure 9). Use approved methods for all connections.
Heater
Vent
Figure 11
2. Remove grill from carton and open light lens area
by pushing in on the two tabs of the light lens and
pulling outward from lens. The lens will swing open
on the connector bars. DO NOT remove the lens
from the grill (Figure 12).
Hot (Blue)
Ground
White
Connector Bar
Hot (Red)
Tabs
Figure 12
Supply from house
Figure 9
3. Install light reflector into grill by lining up the posts on
grill with the holes in light reflector (Figure 13). Raise
light reflector and grill up to housing and insert plug
from light into receptacle marked “LIGHT” (Figure 11).
3. Reinstall the wire compartment cover by sliding the
tabs at the bottom of the cover into the slots in the
housing. Make sure all wires are tucked inside of the
compartment and are not being pinched or showing
through. Reinstall the two screws removed in Step 3
of SECTION 1 Preparing the Unit (Figure 10).
Post
Hole
Light
Slot
Post
Tab
Figure 10
Figure 13
210572111 Rev. B 5-06
4 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach light reflector in place with the two screws
removed during Step 2 in SECTION 1 Preparing the
Unit so grill fits snuggly against ceiling (Figure 14).
SECTION 7
Use and Care
CAUTION: MAKE SURE POWER IS SWITCHED
OFF AT SERVICE PANEL BEFORE SERVICING THE UNIT.
1. Cleaning the Grill: Reverse the instructions in Section
6 Completing the Installation to remove grill. Use a
mild detergent, such as dishwashing liquid, and dry
with a soft cloth. NEVER USE ANY ABRASIVE PADS
OR SCOURING POWDERS. Completely dry grill before
reinstalling. Refer to instructions in Section 6
Completing the Installation, to reinstall grill.
Screws
2. Cleaning the Fan Assembly: Wipe all parts with a
dry cloth or gently vacuum the fan. NEVER IMMERSE
ELECTRICAL PARTS IN WATER.
Figure 14
CAUTION: ALLOW BULBS TO COOL BEFORE
CAUTION: FAILURE TO SECURE THE REFLECTOR
SCREWS MAY RESULT IN A RATTLING OR HUMMING
NOISE.
REPLACING.
3. Changing the Light Bulb: Disconnect power to the
unit. Open light lens by pushing in on the two tabs
of light lens and pulling outward from lens. The lens
will swing open on the connector bars. DO NOT
remove the lens from the grill (Figure 16).
5. Install a 100 watt maximum, type A19 medium base
incandescent bulb (not included).
6. Close the light lens and secure in place by swinging
back into position and snapping the tabs in place
(Figure 15).
Connector Bar
Connector Bar
Tabs
Tabs
Figure 16
4. Unscrew bulb from lamp holder and replace with a
100 watt maximum, type A19 medium base
incandescent bulb.
Figure 15
7. Restore power and test your installation.
Troubleshooting Guide
Trouble
Probable Cause
Suggested Remedy
1. Fan does not operate when the switch is on.
1a. A fuse may be blown or a circuit tripped.
1b. Connector plug from motor is not plugged in.
1a. Replace fuse or reset circuit breaker.
1b. Turn off power to unit. Remove Grill and plug motor into
receptacle in housing. Restore power to unit.
1c. Wiring is not connected properly.
2. Obstruction in the exhaust ducting.
1c. Turn off power to unit. Check that all wires are connected.
2. Fan is operating, but air moves slower than normal.
3. Fan is operating louder than normal.
2. Check for any obstructions in the ducting. The most common
are bird nests in the roof cap or wall cap where the fan
exhausts to the outside.
3a. Motor is loose.
3a. Turn off power to unit. Remove grill and check that all screws
are fully tightened. Restore power to unit.
3b. Fan blade is hitting housing of unit.
3b. Call your dealer for service.
210572111 Rev. B 5-06
5 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
WHAT IS NOT COVERED?
WHAT IS COVERED?
• Installation services or service trips to your home to teach
you how to use the product.
Full Five Year Parts Warranty from date of original proof of
purchase. We will provide, free of charge, a replacement part
that fails due to manufacturing defect in material or workmanship,
when installed and used as directed in the User’s Guide.
• Labor costs or the cost of replacement components as part
of routine maintenance.
This warranty is extended to the original purchaser for products
purchased for ordinary home use.
• Failure or defects in product arising from Improper installation
If you have an installation problem, contact your dealer or
installer. You are responsible for providing adequate
electrical, exhausting and other connecting facilities. See
the Installation Instructions provided with this product for
electrical, exhaust and connection details.
• Replacement of house fuses or resetting of circuit breakers.
• Failure of the product if it is used for something other than
the intended purpose of manufacturer or used commercially.
• Damage to the product caused by accident, fire, floods,
acts of customer, or acts of God.
This warranty contains the sole and exclusive warranty of GE for claims based on defects in these products. Upon the expiration
of the warranty period, all such liability shall terminate. There are no other warranties, whether written, oral, implied or
statutory. NO IMPLIED STATUTORY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY.
IN NO EVENT SHALL GE BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES, SUCH AS, BUT
NOT LIMITED TO, LOSS OF PROFIT OR REVENUES, LOSS OF USE OF THE PRODUCTS OR ANY ASSOCIATED EQUIPMENT, DAMAGE
TO ASSOCIATED EQUIPMENT, OR COST OF SUBSTITUTE PRODUCTS.
IN NO EVENT, SHALL GE’S LIABILITY TO BUYER FROM THE SALE OF THESE PRODUCTS EXCEED THE PRICE OF THE DEFECTIVE
PRODUCT SOLD AND ANY SUCH LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD.
Read your User’s Guide. If you have any questions about operating the product, please contact your dealer.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some states
do not allow limitations on how long an implied warranty lasts, so these exclusions or limitations may not apply to you. This
warranty gives you specific legal rights and you may have other rights which vary from state to state and province to province.
210572111 Rev. B 5-06
6 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS DIAGRAM
2
4
5
1
3
2
2
6
24
30
29
7
8
10
13
12
26
11
2
16
25
9
12
27
14
13
15
15
28
17
19
20
21
22
18
23
#
Qty. Description
Replacement Part #
5S3402039
5S1299002
5S3402040
5S3402041
5S3402042
5S3402043
5S3402044
5S3402045
5S3402046
5S3402047
5S3402048
5S3402049
5S3402050
5S3402051
5S1999004
#
Qty. Description
Replacement Part #
5S3402052
5S3402053
5S3402054
5S3402055
5S3402056
5S3402057
5S3402058
5S3402059
5S3402060
5S3402061
5S3402062
5S3402063
5S3402064
5S1999002
5S1999003
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
4
2
1
1
1
2
2
2
1
2
4
4
1
3
Fan Housing
Mounting Rails
Collar Screw
Collar
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
3
1
1
1
1
1
2
1
1
1
1
2
1
1
Wire Compartment
Receptacle
Lamp Holder
Reflector
Grill
Damper
Motor - Vent
Motor Spacer
Motor Bracket Nut
Lock Washer
Motor Bracket - Vent
Washer
Lock Washer
Hex Nut
Vent Blower Wheel
#8 Screw
Lens Frame
Glass Lens
Reflector Screws
Motor - Heater
Heater Blower Wheel
Blower - Heater
Heater Plug Assembly
Over Heat Protector Screw
#10 Ground Screw
14 ga Ground Wire
210572111 Rev. B 5-06
7 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
210572111 Rev. B 5-06
8 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|