GE Door 19217 User Manual

GE Model 19217  
c. Mark the 4 holes using the base as a template with the arrow pointing up.  
d. If mounting in sheetrock wall, drill 5/32” holes and insert the plastic  
screw anchors, otherwise drill pilot hole for screw.  
e. Mount the chime base using the 4x25mm screws.  
f. Attach the wires for the pushbuttons as shown in the schematic.  
g. Put the cover on the chime  
Wired Chime Kit  
5. Mount the pushbuttons.  
Installation Instructions for Wired Door Kit  
a. Locate the mounting location and pull the wires through the slot in the  
pushbutton.  
b. Remove the pushbutton cover.  
c. Use the base as a template and mark the mounting holes with the arrow  
pointing up.  
d. Drill pilot holes using a 1/16” drill.  
e. Connect the wires matching the schematic.  
f. Put the cover on the pushbutton.  
g. Replace the pushbutton cover.  
Included hardware:  
1: Chime  
2: (2) Push buttons  
3: Transformer  
6. Reapply power and test the chime.  
Replacement Installation  
Included Hardware:  
(4) Plastic screw anchors  
(4) 4x25mm screws (for anchors)  
(4) 3x20mm screws  
1. Shut off power at fuse box or circuit breaker.  
2. Remove the cover from the old door chime and disconnect wires from screw  
terminals and label them for reference.  
3. Install new chime  
a. Remove the cover for the chime.  
b. Pull the wires through the slot in base of chime.  
c. Mark the 4 holes using the base as a template with the arrow pointing up.  
d. If mounting in sheetrock wall, drill 5/32” holes and insert the plastic  
screw anchors, otherwise drill pilot hole for screw.  
e. Mount the chime base using the 4x25mm screws.  
f. Attach the wires for the pushbuttons as shown in the schematic.  
g. Put the cover on the chime.  
(3) Wire nuts  
Required Tools:  
Wire stripper/cutter, small flat blade screwdriver, Phillips screwdriver, drill,  
and drill bit (1/16” and 5/32”)  
Chime Tune Setting  
1. Remove the chime cover and locate the two 3 position dip switches shown  
below.  
For technical support contact Jasco Products Company at 1-800-654-8483  
Made in China  
Hecho en China  
2. Select the desired chime sound from the table below.  
Chime Sound Table  
is a trademark of  
General Electric Company  
and is used under license to  
Jasco Products Company LLC,  
10 E. Memorial Road,  
Oklahoma City, OK 73114.  
19217  
Position  
1
2
3
Westminster  
Ding Dong  
Knock  
Bronze Chime  
Cuckoo Clock  
Foghorn  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
Rev. 3-07  
Gong  
New Installation Instructions  
Use the proper type of wire for your application, in accordance with local  
electrical codes. If you are unsure of the requirements consult a licensed  
electrician.  
1. Shut off power at fuse box or circuit breaker  
2. Locate and mount the included power transformer in a dry location.  
3. Connect the house power to the transformer input as shown in the  
schematic.  
a. House Black to Transformer Black  
b. House White to Transformer White  
c. House Green to Transformer Green  
4. Locate the mounting location for the chime.  
a. Remove the cover for the chime.  
b. Pull the wires through the slot in base of chime.  
Removal and Replacement of Push button cover  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Saw QV 670 User Manual
Everpure Plumbing Product EV9008 20 User Manual
Fiesta Gas Grill EHA2240 B404 User Manual
Fisher Price Stroller FP3456 User Manual
Frigidaire Air Conditioner FRA12EZT2 User Manual
GE Car Amplifier VTPR2100 User Manual
GE Frozen Dessert Maker 681131067652 User Manual
GE Monogram Cooktop Halogen Radiant Cooktop User Manual
GE Washer EWA4500 User Manual
Gianni Industries Door DG 30 User Manual