GE Consumer & Industrial
Appliances
– The dishwasher MUST be installed
to allow for future removal from the enclosure if service is
required.
Read these instructions completely and
carefully.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
– Observe all governing codes and
ordinances.
Optional Accessories – See the Owner’s Manual for available
custom panel kits.
• Note to Installer – Be sure to leave these instructions for the
consumer’s and local inspector’s use.
• Note to Consumer – Keep these instructions with your
Owner’s Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.
• Completion Time – 1 to 3 Hours. New installations require
more time than replacement installations.
Read and observe all CAUTIONS and WARNINGS shown
throughout these instructions. While performing
installations described in this booklet, gloves, safety glasses
or goggles should be worn.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
WARNING
To reduce the risk of electric shock,
fire, or injury to persons, the installer
must ensure that the dishwasher is
completely enclosed at the time of
installation.
This Wall Area
must be Free
of Pipes or
more than 10' in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides and
back, and must not support any part of the enclosure.
24"
Min.
wires
34-1/2"1/4"
Underside of
Countertop
to Floor
5"
5"
4"
4"
Plumbing and Electric Service
Must Enter Inside This Area
Cabinets
Square
and
CLEARANCES: When
installed into a corner,
allow 2" min. clearance
between dishwasher
and adjacent cabinet,
wall or other appliances.
Allow 28-3/8" min. clear-
ance from the front of
the dishwasher for door
opening. Figure B
Countertop
Dishwasher
6"
Plumb
24"
Min.
Floor MUST be Even
With Room Floor.
28-3/8"
• The rough cabinet opening must be at least 24" deep, 24"
wide and approximately 34-1/2" high from floor to underside
of the countertop.
Clearance for Door
Opening 2" Minimum
Figure B
DRAIN REQUIREMENTS
Air gap must be used, if waste tee or disposer
connection is less than 18" above floor to prevent siphoning.
The type of drain installation depends on the following
questions.
®Do local codes or ordinances require an air gap?
®
If the answer to either question is YES, Method 1 MUST
Figure C
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when required by local codes and ordi-
nances. The air gap must be installed according to manufacturer’s
instructions.
• If the answers are NO, either method may be used.
Drain Hose Hanger
Drain Hose Hanger
• Drill a 1-1/2" diameter hole in the cabinet wall within
the shaded areas shown in Figure A for the drain hose
connection. The hole should be smooth with no sharp edges.
32"
32"
Min.
Min.
18"
18"
Min.
Min.
When
connecting drain line to disposer,
check to be sure that drain plug has
been removed. DISHWASHER WILL
NOT DRAIN IF PLUG IS LEFT IN PLACE.
Remove
Drain
Plug
Figure D
Method 2 – “High Drain Loop” with Waste Tee or Disposer
Tip: Avoid unnecessary service call charges
Always be sure disposer drain plug has been removed before
attaching dishwasher drain hose to the disposer.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Alternate
Receptacle
Location
WARNING
18"
1-1/2" Dia. Hole (Max.)
Receptacle
Location
Area
18"
6"
3"
6"
from
Cabinet
Electrical Requirements
24"
from Wall
• This appliance must be supplied with 120V, 60 Hz., and
connected to an individual properly grounded branch circuit,
protected by a 15 or 20 ampere circuit breaker or time delay
• Wiring must be 2 wire with ground and rated for 75°C (176°F).
• If the electrical supply does not meet the above requirements,
call a licensed electrician before proceeding.
Ground
Black
Figure E
White
For models equipped with power cord: Do not modify the plug
provided with the appliance; if it will not fit the outlet, have a
proper outlet installed by a qualified technician.
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
connected to the equipment grounding terminal or lead on
the appliance.
Cabinet Preparation & Wire Routing
• The wiring may enter the opening from either side, rear or the
floor within the shaded area illustrated above in Figure E and
defined in Figure A.
• Cut a 1-1/2" maximum diameter hole to admit the electrical
cable. Permanent wiring connections may pass through the
same hole as the drain hose and hot water line, if convenient.
If cabinet wall is metal, the hole edge must be covered with a
bushing.
Grounding Instructions–Power Cord Models
This appliance must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This appliance is equipped with a cord having an equipment
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and ordinances.
NOTE: Power cords with plug must pass through a separate
hole.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
• For permanent connections the cable must be routed as
shown in Figure E. Cable must extend a minimum of 24" from
the rear wall.
• For power cord connections, install a 3-prong grounding
type receptacle in the sink cabinet rear wall, 6" min. or 18"
maximum from the opening, 6" to 18" above the floor.
WARNING
The improper connection of the equipment
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service representative if you
are in doubt that the appliance is properly
grounded.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
• The line may enter from either side, rear or floor within the
shaded area shown in Figure F.
• The line may pass through the same hole as the electrical
cable and drain hose. Or, cut an additional 1-1/2" diameter
hole to accommodate the water line. If power cord with plug
is used, water line must not pass through power cord hole.
4"
1-1/2" Dia.
Hole
4"
5"
5"
Shut-off
Valve
Hot
6"
2"
From
Cabinet
19" From Wall
2" From Floor
Cabinet Face
Figure F
• Turn off the water supply.
• Install a hand shut-off valve in an accessible location, such
as under the sink. (Optional, but strongly recommended and
may be required by local codes.)
• Water connection is on the left side of the dishwasher. Install
the hot water inlet line, using no less than 3/8" copper tubing.
Route the line as shown in Figure F and extend forward at
least 19" from rear wall.
• Adjust water heater for 120°F to 150°F temperature.
• Flush water line to clean out debris.
• The hot water supply line pressure must be 20-120 PSI.
Turn page to begin dishwasher installation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3: REMOVE WOOD BASE,
Do not remove wood base until you are
ready to install the dishwasher. The dishwasher will
Damage will occur.
• Move the dishwasher close to the installation location and lay
it on its back.
• Remove the four leveling legs on the underside of the wood
base with a 15/16" socket wrench.
• Discard base.
Locate the items in the installation package and set aside for
use in the listed steps:
• Screw kit – Steps 5 or 18 and 15
• Junction box cover – Step 5 or 18
• Drain hose and clamp – Step 7
• Drain hose hanger – Step 17
• Trim pieces (some models) – Step 11
• Owner's Manual - Steps 19 and 22
• Product Samples and/or coupons – Step 22
Approx.
1/8"
• With dishwasher on the wood base, check the door balance
by opening and closing the door.
Figure H
• Door is properly balanced if it gently drops from a 1/2 open
position and does not rise from the full open position.
• If necessary increase or decrease tension
as shown. Latch door and adjust both springs
to the same tension setting to correct balance.
• Screw leveling legs back into the dishwasher frame,
approximately 1/8" from frame as shown.
• Remove the 2 toekick screws and toekick. Set aside for use in
Step 21.
Insert Hook
Over Bracket
Increase
Spring
Tension
Remove 2
Toekick Screws
Correct
Decrease
Spring
Tension
Figure I
Incorrect
Figure G
Tip: Make sure door opens and closes smoothly
Check door opening and closing. If door does not open easily
or falls too quickly, check spring cable routing. The cable is held
in place by “shoulders” on the pulley. Check to be sure cable
has not slipped over the pulley shoulders.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Skip this step if drain hose has been pre-installed
In this step you will need the drain hose and clamp set aside in
Step 1.
Skip this step if dishwasher will be permanently connected
to the house electrical system.
In this step you will need the junction box cover and the
#10 x 1/2" hex head screw from the screw kit set aside in
Step 1.
• Stand dishwasher upright.
The power cord and connections must comply with the
National Electrical Code, Section 422 and/or local codes and
ordinances. Maximum power cord length is 6 feet. Power Cord
Kit WX09X70910, available for purchase from an authorized GE
Appliance Dealer, meets these requirements.
• Place drain hose clamp over 1-3/16" diameter end of drain
hose. Position clamp so screw is on bottom side of hose.
Refer to Figure L.
Prevent drain hose damage and
possible leaks. Be careful not to nick or cut the drain hose.
������������������������
������
�����������������������
• Push the end of the drain hose over the drain pump outlet
being careful not to disturb the check valve. Refer to Figure L.
• Seat the drain hose end against the hose stops on the
pump outlet.
���������������������
�����
������
���
• Position hose clamp against the front lip of the drain hose
and tighten clamp.
�����
Note: Drain hose supplied with dishwasher is approximately
78" long. If a longer hose is needed, a 120" long hose (10 feet)
may be purchased from an authorized GE appliance dealer.
Figure J
The 10' long hose
is part number
GPF10L
Pump Outlet
Hose Stops
• Install strain relief in junction box bracket.
• Insert power cord through strain relief and tighten.
• Make sure black, white and green dishwasher wires are
threaded through small hole in junction box bracket.
• Connect power cord white (or ribbed) to dishwasher white
wire, black (or smooth) to dishwasher black wire and ground
to dishwasher green wire. Use UL listed wire nuts of
appropriate size.
Check Valve
Do Not Remove
Hose Clamp
• Install junction box cover using #10 Hex head screw. Be sure
wires are not pinched under the cover.
• Wrap a 90° elbow with
Front of Dishwasher
thread seal tape.
• Thread 90° elbow
onto the water valve.
• Do not over tighten
elbow. Water valve
bracket could
bend or water valve
90°
fitting could break.
• Position the end of
the elbow to face the
rear of the dishwasher.
Figure L
Water Valve
Tip: Avoid unnecessary service charges. Make a leak free
connection
Insert hose against stop on pump. Position clamp against front
lip of drain hose with clamp screw on bottom side of hose.
Tighten clamp to at least 15 inch-pounds of torque.
Bracket
Elbow
Fill
Hose
Thread Seal Tape
Tip: Reduce drain pump noise
Position drain hose clamp so screw is on the bottom side of the
hose. This will prevent noise caused by the clamp coming in
contact with the tub bottom. Refer to Figure L.
Figure K
7
Download from Www.Somanuals.com. All Manuals Search And Download.
• Position water supply line and house wiring on the floor of the
opening to avoid interference with base of dishwasher and
components under dishwasher.
Do not push against front panel
with knees. Damage will occur.
• Grasp the sides of the front panel and slide dishwasher into
the opening a few inches at a time.
5"
5"
4"
4"
4"
6"
6"
Water
Line
House
Wiring
�������������������
���������������������
Figure M
�������������������
Figure O
������������������������
• As you proceed, pull the drain hose through the opening
under the sink. Stop pushing when the dishwasher extends
about 6 inches forward of adjacent cabinets.
INSTALL DRAIN HOSE,
• Position dishwasher in front of cabinet opening. Insert drain
hose into the hole in cabinet side. If a power cord is used,
guide the end through a separate hole.
• Make certain the house wiring, drain line and water line do
not interfere with components under dishwasher.
(some models)
Maximum Drain Hose
Length 10'
Skip this step if trim is not supplied with the dishwasher.
In this step you will need the trim pieces set aside in Step 1.
Insulation
Blanket
Water
Line
• Position the trim pieces so the lips face toward the
dishwasher door.
• Select a long trim piece and press it onto the left side tub
flange. Start with the top edge and press the trim piece
completely onto the tub flange as you move towards the
bottom. Repeat for the right side tub flange trim piece.
• Install remaining trim piece on the top tub flange.
Drain
Hose
House
Wiring
����������
Power Cord
(If Used)
����
�����
Figure N
����
�����
��������
Tip: Prevent unnecessary service call charges for no fill,
drain or noise concerns
Position utility lines so they do not interfere with anything
under or behind the dishwasher.
Figure P
8
Download from Www.Somanuals.com. All Manuals Search And Download.
• Check the tub insulation blanket, if equipped, to be sure it is
smoothly wrapped around the tub. It should not be “bunched
up” and it must not interfere with the door springs. If the
insulation is “bunched up” or interfering with the springs,
straighten and re-center the blanket prior to sliding the
dishwasher into its final position.
• Slide the dishwasher into the final position by pushing on
the sides of the door panel. Do not use a knee or push on the
center of the panel. If you do, damage to the panel will likely
result.
Skip this step if underside of countertop is wood or
wood-like material.
• Install side-mount brackets if underside of countertop is
granite or similar material that will not accept wood screws.
Note: The brackets are available for purchase if needed. Obtain
a GPF65 kit from your authorized GE Appliance Dealer.
• Fasten the left-hand bracket to the left side
of the dishwasher frame and the right-hand
bracket to the right side of the dishwasher
frame, using the #8 pan-head screws
included with the kit. Refer to instructions
included in kit for orientation and
placement of the brackets.
• The dishwasher is in the final position when the edges of
the front panel are flush with the adjacent cabinets and the
dishwasher is centered in the cabinet opening.
Optional
Side-Mount
Bracket Kit
IMPORTANT – Before opening the dishwasher door,
be certain the edges of the dishwasher door panel are behind
the face of the adjacent cabinet and not up against the cabinet
face. Refer to Figure Q. If the dishwasher door is opened
when the edge of the door is against the face of the cabinet,
dishwasher door damage and cabinet damage will occur.
Side-Mounting Brackets
Tub
• Open and close the dishwasher door to be sure it operates
smoothly, and does not rub on the adjacent cabinet.
Countertop Brackets
Frame
Bracket
Attachment Screws
(2 Each Side)
Door Catches
Door
on Cabinet Frame
Fits and
Swings
Back
Behind
Cabinet
Frame
• If you are installing the dishwasher under a counter with a
short overhang, the countertop brackets may extend beyond
the edge of the counter. If this is the case, remove the excess
length by repeatedly bending the brackets at the notches
until they break off.
Correct
Alignment
Incorrect Alignment
will result in door damage
Figure Q
Tip: Prevent unnecessary service charges for panel damage
or wash performance
Check dishwasher alignment prior to opening dishwasher door
to prevent panel damage.
Make sure utility lines are not trapped or crushed behind
Bend back
and forth
at notch
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 15: POSITION DISHWASHER, SECURE
In this step you will need the 2 Phillips special head screws
from the screw kit set aside in Step 1.
IMPORTANT
– Dishwasher must be level for proper
dish rack operation, wash performance and door operation.
The dishwasher must be leveled left to right and front to back.
This assures the dish racks will not roll in or out on their own,
circulation water will flow to the pump inlet, and the door will
close without hitting the side of the tub.
The dishwasher must be secured to the countertop or the
cabinet sides. When the underside of the countertop is wood,
use Method 1. Use Method 2 when the underside of the
countertop is made of a material, such as granite, that will not
accept wood screws.
• Remove the lower dish rack and place a level on the door and
lower rack track as shown in Figure R.
• Adjust the level of the dishwasher by individually turning the
four legs on the bottom of the dishwasher as illustrated in
Figure S.
• The dishwasher is properly leveled when the level indicator is
centered left to right and front to back. Also, the dishwasher
door should close without hitting the side of the tub.
• Replace the lower rack.
IMPORTANT – Prevent door panel and control panel
damage. Dishwasher must be positioned so the front panel
and control panel do not contact the adjacent cabinets or
countertop. Mounting screws must be driven straight and flush.
Protruding screw heads could scratch the door panel or control
panel and interfere with door operation.
Method 1
Secure dishwasher to underside of wood countertop.
• Recheck alignment of the dishwasher in the cabinet. Refer to
Steps 13 and 14. Door panel and/or control panel must not
hit cabinets or countertop.
• Fasten the dishwasher to the underside of the countertop
with the 2 Phillips special head screws. Refer to Figure T. Make
certain screws are driven straight and flush to prevent panel
damage.
Lower
Check
Rack
Level
Tracks
Check
Level
Front-
to-Back
Side-
to-Side
�������� ����������������
Figure R
Figure T
Secure dishwasher to cabinet sides. This method requires
purchase of a GPF65 Side Mount Kit. Refer to Step 12.
• Recheck alignment of the dishwasher in the cabinet. Refer to
Steps 13 and 14. Door panel and/or control panel must not
hit cabinets or countertop.
• Fasten the dishwasher to the adjacent cabinets with the 2
Phillips special head screws provided. Refer to Figure U. Make
certain screws are driven straight and flush to prevent panel
damage.
���������
���������
Figure S
Tip: Prevent unnecessary service charges. Verify dishwasher
is leveled
������������������
Pull the dish racks half way out . They should stay put. Open
and close the door. The door should fit in the tub opening
without hitting the side of the tub. If the racks roll on their own,
or the door hits the side of tub, re-level the dishwasher
�������������
Figure U
10
Download from Www.Somanuals.com. All Manuals Search And Download.
• Connect drain line to air gap, waste tee or disposer
using the previously determined method. Secure hose
with a screw type clamp.
Connect water supply line to 90° elbow.
• Slide compression nut, then ferrule over end of water line.
• Insert water line into 90° elbow.
• Slide ferrule against elbow and secure with compression nut.
Method 1 – Air gap with waste tee or disposer
Check to be sure that door spring
and/or door spring cable do not rub or contact the fill hose or
water supply line.
Compression
Test by opening and
Nut
closing the door.
Re-route the water
supply lines if a
rubbing noise or
interference
Ferrule
Disposer Installation
Waste Tee Installation
Hot Water
Supply Line
90° Elbow
Figure Y
occurs.
Method 2 – “High drain loop” with waste tee or disposer
With this method you will need the drain hose hanger set aside
in Step 1.
Fasten drain hose to underside of countertop with the provided
hanger.
90° Elbow
Figure V
Door Spring
Drain Hose Hanger
The molded end of the drain hose will fit 5/8" through 1"
diameter inlet ports on the air gap, waste tee or disposer.
• Determine size of inlet port
32"
Min.
32"
Min.
18"
Min.
18"
Min.
• Cut drain hose connector on the marked line, if required, to fit
the inlet port.
Waste Tee Installation
Figure Z
Disposer Installation
Cutting Line
When connecting drain line to
disposer, check to be sure that drain plug has been removed.
DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE.
1"
5/8"
IMPORTANT: Do not cut corrugated
Figure W
Remove
Drain
Plug
portion of hose
• If a longer drain hose is required and you did not purchase
drain hose GPF10L, add up to 42" length for a total of 120"
(10 feet) to the factory installed hose. Use 5/8" or 7/8" inside
diameter hose and a coupler to connect
the two hose ends.
Tip: Avoid unnecessary service call charges for a no drain
complaint
Make sure excess drain hose has been pulled through
the cabinet opening. This will prevent excess hose in the
dishwasher cavity from becoming kinked or crushed by the
dishwasher.
Secure the
connection
with hose
clamps.
����������
�������
����������
Figure X
TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10 FEET
FOR PROPER DRAIN OPERATION.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
If a power cord with plug is already installed proceed to
Step 19.
Review this list after installing your dishwasher to avoid
charges for a service call that is not covered by your
warranty.
■ Check to be sure power is OFF.
WARNING
If house wiring is not 2-wire with ground, a
■ Open door and remove all foam and paper packaging.
■ Locate the Owner’s Manual set aside in Step 1.
■ Read the Owner’s Manual for operating instructions.
ground must be provided by the installer.
When house wiring is aluminum, be sure to
use UL Listed anti-oxidant compound and
aluminum- to-copper connectors
■ Check door opening and closing. If door does not open and
close freely, check for proper routing of spring cable over
pulley. If door drops or closes when released, adjust spring
tension. See Step 2,
In this step you will need the junction box cover and the
#10 Hex head screw from the screw kit set aside in Step 1.
■ Check to be sure that wiring is secure under the dishwasher,
not pinched or in contact with door springs or other
components. See Step 10.
• Secure house wiring to the back of the junction box with a
• Locate the three dishwasher wires, (white, black and green)
with stripped ends. Insert dishwasher wires through the small
hole in the junction box bracket. Use UL listed wire nuts of
appropriate size to connect incoming ground to green, white
■ Check door alignment with tub. If door hits tub, level
dishwasher. See Steps 14 and 15.
■ Pull lower rack out, about halfway. Check to be sure it does
not roll back or forward on the door. If the rack moves,
adjust leveling legs. See Step 14.
• Install the junction box cover using #10 hex head screw.
Check to be sure that wires are not pinched under the cover.
■ Check door alignment with cabinet. If door hits cabinet,
Note: Check That Harness
reposition dishwasher. See Step 15.
Ground
Leads Are Threaded Thru
Small Hole in Bracket
■ Check that door spring does not contact water line, fill hose,
wiring or other components. See Step 16.
White
Do Not
Use
■ Verify water supply and drain lines are not kinked or in
contact with other components. Contact with motor or
dishwasher frame could cause noise.
Black
■ Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must
be between 120°F and 150°F. A minimum of 120°F
temperature is required for best wash performance. See
“Prepare Hot Water Line,” page 5.
Figure AA
■ Add 2 quarts of water to the bottom of the dishwasher to
lubricate the pump seal.
■ Turn on water supply. Check for leaks. Tighten connections
if needed.
■ Remove protective film if present from the control panel
and door.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Turn on power supply or plug power cord into outlet,
• Place toekick against the legs of the dishwasher.
if equipped.
■ Latch door.
■ Push “Rinse Only” pad.
■ Push Start/Reset pad one time. Dishwasher should start.
■ Check to be sure that water enters the dishwasher. If water
does not enter the dishwasher, check to be sure that water
and power are turned on.
■ Check for leaks under the dishwasher. If a leak is found,
turn off power at the breaker, and then tighten water
connections. Restore power after leak is corrected.
T
oek
ick
Attachment
Screws
■ Check for leaks around the door. A leak around the door
could be caused by door rubbing or hitting against
adjacent cabinets. Reposition the dishwasher if necessary.
See Step 15.
Figure CC
• Align the toekick with the bottom edge and make sure it is
against the floor.
• Insert and tighten the two toekick attachment screws. The
toekick should stay in contact with the floor.
■ The dishwasher will drain and turn off about 5 minutes after
it was started. Check drain lines. If leaks are found, turn off
power at the breaker and correct plumbing as necessary.
Restore power after corrections are made. See Steps 7
and 17.
Make sure toekick is against floor.
■ Open dishwasher door and make sure most of the water
has drained. If not, check that disposer plug has been
removed and/or air gap is not plugged. Also check drain
hose to be sure it is not kinked underneath or behind
dishwasher. See Step 17.
• Be sure to leave complete literature package, these
Installation Instructions and product samples and/or coupons
with the consumer.
■ Press Start/Reset pad once again and run dishwasher
through another “Rinse Only” cycle. Check for leaks and
correct if required.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
GE Consumer & Industrial
General Electric Company
Louisville, Kentucky 40225
© 2005 General Electric Company
Pub. No. 31-30217
Dwg. No 206C1559P157
ND 06G-1871 (8/06)
ge.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|