ge.com
Safety Information . . . . . . . . 2–5
Owner’s Manual
Operating Instructions
DCCB330
DCCD330
Countdown Display . . . . . . . . . . . . . .7
Reversing the Door . . . . . . . . . . . . . .6
Venting . . . . . . . . . . . . . . . . . . . . . . . . .8
Care and Cleaning . . . . . . . . . . 9
Consumer Support
Consumer Support . . . . .Back Cover
General Principles
of Good Practice . . . . . . . . . . . . . . .11
Warranty . . . . . . . . . . . . . . . . . . . . . 10
Write the model and serial
numbers here:
Model # ______________
Serial #________________
They are on the label on the front
of the dryer behind the door.
175D1807P538 49-90270 12-05 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
ge.com
PROPER INSTALLATION
This dryer must be properly installed and located in accordance with the Installation Instructions
before it is used. If you did not receive an Installation Instructions sheet, you can receive one by
visiting ge.com, or by calling 800.GE.CARES (800.432.2737).
I Properly ground dryer to conform with all
governing codes and ordinances. Follow details
in the Installation Instructions section.
I Remove any accumulated time by manually
rotating timing cam in the coin box
counterclockwise until switch shuts off. Apply
a slight additional counterclockwise pressure to
further seat drive. Make certain not to turn cam
past switch shutoff position. Otherwise, one
increment of time will be gained. Switches are
off when the plastic switch actuating arm (inner)
is down and all 3 switch buttons are depressed.
I Install or store where it will not be exposed to
temperatures below freezing or exposed to
the weather.
I Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
I Remove all sharp packing items and dispose of
all shipping materials properly.
Exhaust/Ducting
This dryer MUST be exhausted to the outside.
I In fulfilling the specific needs of different
commercial installations the purchaser of this
dryer may wish to locate the coin box and
controls in any of a number of locations.
The responsibility for the proper performance
of this work lies solely with the purchaser.
It should be done by properly trained and
qualified personnel, and in accordance with
local code requirements.
1
Use only rigid metal 4″ diameter ductwork
inside the dryer cabinet. Use only rigid metal
2
or flexible metal 4″ diameter ductwork for
exhausting to the outside. USE OF PLASTIC OR
OTHER COMBUSTIBLE DUCTWORK CAN CAUSE
A FIRE. PUNCTURED DUCTWORK CAN CAUSE A
FIRE IF IT COLLAPSES OR BECOMES OTHERWISE
RESTRICTED IN USE OR DURING INSTALLATION.
I Any coin box or similar device added to
the dryer, either electrically or mechanically,
should be properly grounded.
Follow details in the Installation Instructions section.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
YOUR LAUNDRY AREA
I Keep the area underneath and around your
appliances free of combustible materials, such
as lint, paper, rags, chemicals, gasoline and
other flammable vapors and liquids.
I Close supervision is necessary if this appliance
is used by or near children. Do not allow
children to play on, with, or inside this or
any other appliance.
I Keep the floor around your appliances clean
and dry to reduce the possibility of slipping.
I Keep all laundry aids (such as detergents,
bleaches, etc.) out of the reach of children,
preferably in a locked cabinet. Observe all
warnings on container labels to avoid injury.
I Keep area around the exhaust opening and
surrounding areas free from the accumulation
of lint, dust and dirt.
I Never climb on or stand on the dryer top.
I Do not obstruct the flow of ventilating air.
Do not stack or place laundry or throw rugs
against the front or back of the dryer.
I Do not install or store this appliance where it
will be exposed to the weather.
WHEN USING YOUR DRYER
I Never reach into the dryer while the drum is
moving. Before loading, unloading or adding
clothes, wait until the drum has completely
stopped.
I Do not dry articles containing rubber, plastic
or similar materials such as padded bras, tennis
shoes, galoshes, bath mats, rugs, bibs, baby pants,
plastic bags, pillows, etc. that may melt or burn.
Some rubber materials, when heated, can under
certain circumstances produce fire by
I Clean the lint filter before each load to prevent lint
accumulation inside the dryer or in the room.
DO NOT OPERATE THE DRYER WITHOUT THE LINT
FILTER IN PLACE.
spontaneous combustion.
I Do not store plastic, paper or clothing that
may burn or melt on top of the dryer during
operation.
I Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry-cleaning
solvents, kerosene, etc.) which may ignite or
explode. Do not add these substances to the
wash water. Do not use or place these substances
around your washer or dryer during operation.
I Garments labeled Dry Away from Heat or Do Not
Tumble Dry (such as life jackets containing Kapok)
must not be put in your dryer.
I Do not dry fiberglass articles in your dryer.
Skin irritation could result from the remaining
particles that may be picked up by clothing
during subsequent dryer uses.
I Any article on which you have used a cleaning
solvent or that contains flammable materials
(such as cleaning cloths, mops, towels used in
beauty salons, restaurants, or barber shops, etc.)
must not be placed in or near the dryer until
solvents or flammable materials have been
removed. There are many highly flammable
items used in homes such as acetone, denatured
alcohol, gasoline, kerosene, some household
cleaners, some spot removers, turpentines,
waxes, wax removers and products containing
petroleum distillates.
I To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the dryer at the distribution panel
by removing the fuse or switching off the circuit
breaker before attempting any maintenance or
cleaning (except the removal and cleaning of
the lint filter). NOTE: Turning the Cycle Selector knob to
an off position does NOT disconnect the appliance from
the power supply.
I Do not spray any type of aerosol into, on or near
dryer at any time.
I The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s
care instructions.
I Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ge.com
WHEN USING YOUR DRYER (cont.)
I Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a
damaged cord or plug.
I You may wish to soften your laundered fabrics
or reduce the static electricity in them by using
a dryer-applied fabric softener or an anti-static
conditioner. We recommend you use either
a fabric softener in the wash cycle, according
to the manufacturer’s instructions for those
products, or try a dryer-added product for
which the manufacturer gives written assurance
on the package that their product can be safely
used in your dryer. Service or performance
problems caused by use of these products are
the responsibility of the manufacturers of
those products and are not covered under
the warranty to this appliance.
I The interior of the machine and the exhaust
duct connection inside the dryer should be
cleaned at least once a year by a qualified
technician. See the Care and Cleaning section.
Do not use any type of spray cleaner when
cleaning dryer interior. Hazardous fumes or
electrical shock could occur.
I If yours is a gas dryer, it is equipped with an
automatic electric ignition and does not have
a pilot light. DO NOT ATTEMPT TO LIGHT WITH
A MATCH. Burns may result from having your
hand in the vicinity of the burner when the
automatic ignition turns on.
WHEN NOT USING YOUR DRYER
I Grasp the plug firmly when disconnecting this
appliance to avoid damage to the cord while
pulling. Place the cord away from traffic areas
so it will not be stepped on, tripped over or
subjected to damage.
I Before discarding a dryer, or removing it from
service, remove the dryer door to prevent
children from hiding inside.
I Do not tamper with controls.
I Do not attempt to repair or replace any part of
this appliance or attempt any servicing unless
specifically recommended in this Owner’s Manual
or in published user-repair instructions that you
understand and have the skills to carry out.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the door.
Tools needed:
I Standard #2
Phillips screwdriver
I Tape-tipped
putty knife
Open the door and remove the filler plugs opposite the hinges. With the
door completely open, remove the bottom screw from each hinge on the
dryer face. Insert these screws about halfway into the TOP holes, for each
hinge, on the opposite side (where you removed the filler plugs).
Apply firm pressure to get the screw started in new holes.
1
Loosen top screw from each hinge on the dryer face halfway. With one hand
holding the top of the door and the other hand holding the bottom, remove
the door from the dryer by lifting it UP and OUT.
2
3
Rotate the door 180°. Insert it on the opposite side of the opening by moving
the door IN and DOWN until the top hinge and the bottom hinge are resting
on the top screws inserted in step 1.
Remove the remaining screws from the side of the opening from which
the door was removed. With these screws secure each hinge at the bottom.
Tighten the two top screws of each hinge. Reinsert the plastic plugs on
the side from which the door was removed.
4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Countdown display. (DCCD models only)
ge.com
The countdown display shows the remaining operating time as well as the current drying cycle. The
display board is configured for a 45-minute dry time at the factory to correspond with the 45-minute
timer cam pre-installed in the coin box. If the timer cam is modified for another operating duration,
the dip switches on the display board should be set as follows:
DIP SWITCH NUMBERS
DRYING TIME (minutes)
1
1
1
0
0
2
1
0
1
0
45
60
90
120
NOTE: This display does not accumulate time. See the following examples of display possibilities.
DIP SWITCH SETTING (min)
45
COIN SLIDE ACTUATIONS
1
DISPLAY READING (min)
45 to 0, then blank
45
2
45 to 1, then 1 for next 45 min.,
then 0 and blank
120
1
99 for 21 minutes, then 98 to 0,
then blank
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting the dryer.
For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy
and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the
Installation Instructions.
I Use only rigid metal 4″ diameter ductwork inside the dryer cabinet. Use only rigid metal or
flexible metal 4″ diameter ductwork for exhausting to the outside.
I Do not use plastic or other combustible ductwork.
I Use the shortest length possible.
I Do not crush, kink or collapse the duct.
I Avoid resting the duct on sharp objects.
I Venting must conform to local building codes.
Correct
Venting
Incorrect
Venting
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and cleaning.
Care and Cleaning of the Dryer
ge.com
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control
panel and finishes may be damaged by some
laundry pretreatment soil and stain remover
products. Apply these products away from the
dryer. The fabric may then be washed and dried
normally. Damage to your dryer caused by these
products is not covered by your warranty.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a year to prevent clogging.
A partially clogged exhaust can lengthen the
drying time.
Follow these steps:
Turn off electrical supply by disconnecting the
1
plug from the wall socket.
The Lint Filter: Clean the lint
filter before each use.
Moisten your fingers and
reach into the filter opening.
Run your fingers across the
filter. Have a qualified
Disconnect the duct from the dryer.
2
Vacuum the duct with the hose attachment and
reconnect the duct.
3
The Exhaust Hood: Check from the outside that the
flaps of the hood move freely when operating. Make
sure that there is no wildlife (birds, insects, etc.)
nesting inside the duct or hood.
technician vacuum the lint
from the dryer once a year.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GE Commercial Dryer Warranty.
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
Parts and service are available from your General Electric
Commercial Laundry distributor.
Please have serial number and model number available
when calling for service.
For The Period Of:
We Will Replace:
Three Years
From the date of the
original purchase
Any part of the dryer which fails due to a defect in materials or workmanship. During this
limited three-year warranty, you will be responsible for any labor and related service costs.
Five Years
From the date of the
original purchase
The dryer drum, if it should fail due to a defect in materials or workmanship, and the cabinet
side panels, base and cover, if they should fail due to rust-through. During this limited additional
two-year warranty, you will be responsible for any labor and related service costs.
What Is Not Covered:
I Coin drop meter, coin slide mechanism, coin vault and
locks, smart card modules and cards, smart card system
accessories.
I Replacement of fuses or resetting of circuit breakers at
place of business.
I Damage to the product caused by accident, fire, floods or
I Service trips to your place of business to teach you
acts of God.
how to use the product.
I Incidental or consequential damage caused by possible
I Improper installation, delivery or maintenance.
defects with this appliance.
I Failure of the product if it is abused, misused, or
I Damage caused after delivery.
used for other than the intended purpose.
I Product not accessible to provide required service.
I Replacement of the light bulb.
I Any and all implied warranties of merchantability and
fitness for a particular purpose.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this
Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a
particular purpose, are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
commercial use within the USA. If the product is located in an area where service by a GE Authorized Servicer
is not available, you may be responsible for a trip charge or you may be required to bring the product to an
Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping to your
place of business.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
10
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC DRYER
COMMERCIAL APPLICATION
GENERAL ELECTRIC DRYERS
GENERAL PRINCIPLES OF GOOD PRACTICE
(COIN-OPERATED MODELS ONLY)
In fulfilling the specific needs of different commercial installations, the purchaser of this
General Electric automatic dryer may wish to locate the coin box and controls in any of
a number of locations. The responsibility for the proper performance of this work lies
solely with the purchaser. It should be done by properly trained and qualified personnel,
and in accordance with local code requirements.
In addition, General Electric Company assumes no responsibility or liability whatsoever to
the purchaser for any patent infringement expenses, either in the form of damages or legal
costs, where the alleged infringement is based on a patent claim including one or more
components added by the purchaser (i.e., not supplied by General Electric Company with
the purchased dryer).
Set forth below are some general principles which should be followed by persons installing
the coin box and controls in the desired location. This listing is not all-inclusive, and is
only intended to serve as a general guide. These principles are intended to supplement,
not modify, the Installation Instructions which accompany the automatic dryer.
1. Any component added to the automatic dryer, either electrically or mechanically,
should be properly grounded.
2. All current-carrying metal parts should be isolated from possible contact by the user.
3. All wiring should be properly protected from sharp edges, burrs, moving parts and other
agencies which might cause abrasion of the insulation on the conductors.
4. All electrical connections should be mechanically secure, and should provide adequate
and reliable electrical contact under conditions, such as vibration, to which they may be
subjected.
5. All electrical components, wires, and terminals should be of proper electrical rating for
the specific application.
6. All insulating materials should remain effective under the specific conditions to which
they will be exposed (e.g., humidity, temperature, etc.).
7. The installation should not be incompatible with the electrical circuit within the
automatic dryer nor in any manner interfere with either the safety devices or the
sequence of operations of the cycle which are engineered into the appliance.
8. Uninsulated current-carrying metal parts should have adequate and ensured permanence
of spacing from other parts.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Support.
GE Appliances Website
ge.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
™
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts ”
your questions, and so much more...
Schedule Service
ge.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio
ge.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties
ge.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
ge.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
ge.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
ge.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Printed in Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|