GE Beverage Dispenser r10279v User Manual

Design Guide with  
Installation  
Instructions  
Wine Chiller, Wine Reserve  
and Beverage Center  
monogram.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Guide  
THE INSTALLATION SPACE  
PRODUCT CLEARANCES  
The stainless steel wine chiller, wine reserve and beverage  
center is factory set for a 110° door swing. Models that accept  
custom panels have a 95° door swing.  
Locate  
Outlet  
When installed in a corner:  
Allow 4min. clearance on the hinge side for the 90° door  
10-1/2"  
swing and to allow racks to slide out.  
24"  
• Allow 10minimum clearance on the hinge side for a full  
110° door swing. (Models ZDWI240WII and ZDBI240WII have  
a 95° door swing.)  
9" Max.  
34-1/2"-35"  
24-1/8" Framed Models  
23-3/4" Stainless Steel Models  
1-1/2"  
23-3/4" Min.  
NOTE: Custom handle clearances may vary, depending on  
custom handle depth.  
10" Minimum  
to Wall  
90° Door Swing  
34-1/4"  
to 34-3/4"  
NOTE:  
Handle  
21-5/8"  
23-5/8"  
and handle  
standoff depth  
is 1-3/4″  
23-3/4"  
The cutout depth should be 24″  
90°  
The cutout dimensions shown allow for a full door swing  
and access to the pull-out racks when installed as a  
built-in in standard 24deep cabinets.  
110°*  
*95° Door Swing on Custom Frame Models  
4" Minimum  
to Wall  
• The wine chiller, wine reserve and beverage center  
can be installed freestanding.  
• The door swing is reversible on all models. If desired, change the  
door swing before installation or before installing the custom frame  
panel.  
• If installing between frameless cabinets, a 1/2wide  
filler strip or side panel may be needed on hinge side.  
The filler strip will act as a spacer between the case  
and adjacent cabinet door swing. The width  
of the opening must include the filler panels.  
NOTE: The door should protrude 1beyond the  
surrounding cabinets. Custom framed models will  
protrude 1-7/8beyond surrounding cabinet doors.  
Choose the location:  
• These products may be closed in on the top and three sides as long  
as the front is unobstructed for air circulation and proper access to  
the door.  
• Do not install these products where the temperature will go below  
55°F (13°C) or above 90°F (32°C).  
• Do not install where it will be subject to direct sunlight, heat or  
moisture.  
• These products are not designed to be stacked one over the other.  
Additional Specifications  
A 120 volt 60Hz., 15 or 20 amp power supply is  
required. An individual properly grounded branch  
circuit or circuit breaker is recommended. Install a  
properly grounded 3-prong electrical receptacle  
recessed into the back wall as shown. Electrical must  
be located on rear wall as shown. NOTE: GFI (ground  
fault interrupter) is not recommended.  
Black or Stainless Steel Toekick Options  
• These products are shipped with a black toekick installed.  
An optional stainless steel toekick is also supplied with each  
product. For shipping purposes, the stainless steel toekick is  
secured to the back of the unit.  
ZTBSS1 Tubular Handle  
ZTBSS1 Monogram stainless steel tubular handle is available for  
models ZDWI240WII and ZDBI240WII.  
SIDE-BY-SIDE INSTALLATIONS  
Increase storage capacity by installing two Monogram  
beverage centers, wine chillers or wine reserves together.  
Or, for a complete refreshment center, install any two  
of these units together.  
• A side-by-side installation requires at least a 47-1/2″  
wide opening. No trim kits required.  
Locate  
Outlet  
10-1/2"  
10-1/2"  
24"  
14"  
34-1/2"-35"  
9" 9"  
15"  
1-1/2"  
• Products must operate from separate, properly  
grounded receptacles.  
47-1/2" Min.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
TOOLS REQUIRED  
STAINING WOOD DRAWER FRONTS  
• #2 Phillips screwdriver  
• Adjustable wrench  
The drawer fronts are unfinished cherry wood. During  
use, oil from hands may accumulate and stain the  
wood.  
• The drawer fronts may be stained and sealed to  
match adjacent cabinetry. The tinted glass will make  
the stained wood appear darker. A true color match  
can be seen only when the door is opened.  
• Apply the stain and sealer according to the  
manufacturer’s instructions. To avoid unpleasant  
odor, keep the door open to ventilate and allow  
the stain/sealer to dry completely before using  
the product.  
PARTS SUPPLIED  
• Monogram nameplate  
• Hardware for changing door swing  
• Optional stainless steel toekick with screws and  
spacers  
• Left and right side hinge covers  
• Top screw hole cover  
GROUNDING THE WINE CHILLER,  
WINE RESERVE AND BEVERAGE  
CENTER  
INSTALLING THE CUSTOM FRAME PANEL  
Go to page 6 for custom frame panel size, depending  
on your cabinet size and style.  
• Install a custom handle of your choice or optional  
ZTBSS1 Tubular Handle onto the custom panel before  
the panel is secured to the door.  
• The custom panel should be installed before sliding  
the product into the installation location.  
IMPORTANT –  
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE  
PROPERLY GROUNDED.  
Please read carefully.  
The power cord of this appliance is equipped with a  
three-prong (grounding) plug which mates with a  
standard three-prong (grounding) wall receptacle to  
minimize the possibility of electric shock hazard from  
this appliance.  
STEP 1 REMOVE PACKAGING  
• Remove corner blocks and foam drawer stops.  
• Remove all packing material, tape and protective  
plastic coverings.  
Have the wall outlet and circuit checked by a qualified  
electrician to make sure the outlet is properly grounded.  
• Remove stainless steel toekick taped to the back  
of the unit.  
Where a standard 2-prong wall outlet is encountered, it  
is your personal responsibility and obligation to have it  
replaced with a properly grounded 3-prong wall outlet.  
CAUTION:  
Small objects are a choke hazard  
for children. Remove and discard any parts not used.  
DO NOT, UNDER ANY  
CIRCUMSTANCES, CUT  
OR REMOVE THE THIRD  
(GROUND) PRONG  
MISE EN GARDE :  
piéces qui ne sont pas utilisées.  
Les petits objets  
peuvent étrangler les enfants. Il faut jeter toutes les  
FROM THE POWER CORD.  
DO NOT USE AN ADAPTER PLUG TO CONNECT THE  
REFRIGERATOR TO A 2-PRONG OUTLET.  
DO NOT USE AN EXTENSION CORD WITH THIS  
APPLIANCE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
STEP 2 REVERSE DOOR SWING  
SKIP THIS STEP IF DOOR SWING SUITS THE  
INSTALLATION  
Install  
3 Hinge  
Screws  
Parts Included:  
• Top left case hinge  
Remove  
Top Hinge  
• Bottom left case hinge  
• Left and right side decorative hinge cover  
• Decorative hinge screw hole cover  
• Torx® driver bit  
Hinge  
Pin and  
Bracket  
Tools Required:  
• Phillips screwdriver  
• Electric drill  
Door Stop  
and Cam Riser  
Remove the door:  
• Flatten the shipping carton to use as a pad.  
• Remove the 2 screws and the toekick. Set aside the  
screws and toekick for final installation.  
• Use the supplied Torx® bit and electric drill to remove  
the 3 screws holding the top case hinge. Lift off the  
hinge. (Screws will be used to install the new hinge.)  
• Lift the door off the bottom case hinge.  
• Remove the bottom case hinge pin and bracket.  
Remove  
Hinge  
Apply Monogram Nameplate:  
• Install the Monogram nameplate. See instructions  
and template on back cover.  
Rotate the door:  
The handle will be on the right side of the door; hinges  
will be installed on the left side of the case.  
• Remove the door stop and cam riser on the original  
bottom right side of the door.  
• Remove the fill plug on the top right side  
of the door.  
Install Toekick  
The toekick has a  
cutout on the left  
and right sides.  
Remove  
• Turn the door over and reinstall the fill plug on the  
new left side.  
the plug on  
the left side  
and  
reinstall on  
the right  
Move Fill  
Reinstall the door:  
• Install the original door stop and cam riser onto the  
bottom left side of the door.  
Plug to  
Right Side  
side. If you  
choose to  
• Install the new supplied bottom case hinge pin and  
bracket onto bottom left side.  
install the  
stainless steel toekick,  
• Place the door onto the bottom case hinge.  
• Install the supplied left-hand top case hinge with the  
3 original screws.  
• Select the hinge cover marked with an “L”.  
• Peel backing off the tape inside the decorative hinge  
reinstall the plug on the right side of that toekick.  
• Install original screws and spacers or screws and  
spacers supplied with the stainless steel toekick.  
Install screws through the spacer standoff, toekick  
and into the base as shown.  
cover.  
Install Covers  
• Press and snap the hinge  
cover into place.  
• Snap the screw hole cover into  
place on the opposite side.  
IMPORTANT:  
Check to be sure screws are tight and that the door  
is straight and does not sag. The door should swing  
freely.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
CUSTOM FRAME PANEL MODELS  
STEP 3 LEVEL  
Model ZDWI240WII and ZDBI240WII  
• Use an adjustable wrench to turn the leveling legs and  
raise or lower the product.  
These models require a custom panel frame surrounding  
the glass. There are two options: the panel may be 29-3/4″  
or 30high. A 30panel requires a notch cut into the bottom  
of the panel to avoid interference with the hinges.  
• Rout the back side of the panel to the dimensions shown.  
• Adjust carefully; the product should be level and plumb  
with cabinetry, and should align with adjacent toekick  
height.  
• A custom handle of your choice or ZTBSS1 Tubular Handle  
must be installed before the panel is mounted onto  
the door.  
Turn Right to Lower  
Turn Left to Raise  
NOTE: The 4 corners  
of the routed areas  
must be squared  
to fit the corners  
of the metal  
door frame.  
Option 1  
Option 2  
23-1/8”  
23-1/8”  
2-1/4”  
2-1/4”  
wide,  
If you skipped Step 2:  
• Select the hinge cover marked “R” or “L”, depending  
on door swing.  
• Peel backing off the tape inside the decorative  
hinge cover. Press and snap into position.  
• Snap the screw hole cover into place on the  
opposite side.  
all sides  
25-1/4”  
25-1/4”  
Rout the back  
side of the  
opening 7/16”  
deep, 1-1/8” wide  
Rout the  
back side  
of the  
opening  
7/16”deep,  
1-1/8” wide  
GLASS  
18-5/8”  
30”  
29-3/4”  
GLASS  
18-5/8”  
2-1/2” at  
bottom  
3/4” Thick Custom Panel,  
Back Side  
2-1/4”  
2-1/4”  
1/8”  
1/4”  
Cut the notch  
1/8” deep, 1/4”  
wide and 1/4”  
high  
NOTE: Right-hand models  
illustrated. Cut notches  
for hinge clearance on the  
opposite side for left-hand  
door swing.  
STEP 4 CONNECT POWER  
1/4”  
• Connect power cord plug to a properly grounded  
receptacle.  
• Check to make sure power is on by opening the door  
to see if interior light turns on.  
Choose Option 1 or Option 2 panel size depending on  
cabinetry size or style.  
NOTE: A solid panel that covers the door glass CANNOT be  
installed on these models.  
STEP 5 SLIDE PRODUCT INTO  
THE CUTOUT  
Install the custom panel:  
• Open the door fully.  
• Remove the gasket surrounding the inside of the door to  
expose the existing screw holes for the custom panel.  
• Hold the custom frame panel against the door and align  
carefully, top to bottom and side to side. Mark screw hole  
locations on the back side of the panel.  
Carefully, slide the unit into the opening. Be careful  
not to entangle the power cord.  
Make certain that the door protrudes 1beyond  
the surrounding cabinets (1-7/8for custom frame  
models).  
• Check again to be sure the unit is level.  
• Drill pilot holes in the back side of the custom panel. In  
hardwood, drill 3/32pilot holes. In softwood, drill 5/64holes.  
• Secure the prepared panel to the door using ten (10)  
#8 x 5/8screws. Drive the screws through the door frame  
and into the wood.  
STEP 6 INSTALL NAMEPLATE  
• Replace the gasket.  
• Follow instructions on the back page for installation of  
the Monogram nameplate.  
#8 x 5/8"  
Screws  
GLASS  
Back  
Door  
Frame  
STEP 7 SET TEMPERATURE CONTROLS  
• The temperature controls are preset. Refer to the  
Owner’s Manual for more information. Allow 24 hours  
for temperature to stabilize.  
Custom  
Framed  
Panel  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZTBSS1 Monogram Tubular Handle Kit  
TOOLS AND MATERIALS REQUIRED  
BEFORE YOU BEGIN:  
• Gloves to protect against sharp edges  
• #2 Phillips screwdriver  
• Drill and 1/4bit and 1/2spade bit  
• Safety glasses  
Read these instructions completely and carefully.  
IMPORTANT –  
Save these instructions  
for local inspector’s use.  
• Center punch  
• Pencil  
IMPORTANT –  
Observe all governing codes  
and ordinances.  
Note to Installer Be sure to leave these  
THIS KIT INCLUDES  
instructions with the Consumer.  
• Tubular handle  
• 2 Mounting screws  
• 2 Handle standoffs  
• 2 Set screws for standoffs  
• 2 Nuts  
Note to Consumer Keep these instructions  
with your Owner’s Manual for future reference. This kit  
provides a stainless steel tubular handle to coordinate  
with other Monogram appliances.  
• 2 Washers  
• Allen Wrench  
• The tubular handle must be installed onto the 3/4thick  
portion of the custom wood panel before the panel is  
secured to the door.  
INSTALL THE TUBULAR HANDLE  
7/8”  
• Use the handle as a template to locate and mark the  
exact position of the screw holes. Be careful to avoid  
interference with custom panel mounting screws.  
• Draw a pencil line, top to bottom and 7/8from the  
outside edge.  
30”  
24-7/32”  
• Hold the tubular handle against the appearance side,  
centered on the marked line.  
• Mark the screw hole locations at the center of the  
handle attachment posts.  
• Center punch the marked hole locations. Drill 1/4″  
pilot holes from the appearance side through the  
entire panel thickness.  
• Use a 1/2spade bit to drill 1/4to 5/16deep into  
the back side of the panel. Insert washer (spacer) into  
the hole.  
Custom  
Framed  
Panel  
Tubular  
Handle  
Handle  
Standoff  
• Install screw through the handle standoff and into the  
pilot hole.  
• Fasten nut onto the screw until the standoff is tight  
against the panel. The screw hole on the standoff  
should be pointing down toward the floor.  
• Place handle attachment posts inside the standoffs.  
• Use the Allen wrench to install the set screws. Tighten  
handle to standoffs.  
Handle  
Attachment  
Post  
Washer  
Nut  
Set  
Screw  
Screw  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
TEMPLATE FOR NAMEPLATE LOCATION  
Cut on Dotted Line  
Upper Left  
Corner of  
Upper Right  
Corner of  
Glass if Hinge  
is on Right  
Top of Glass Door  
Glass if Hinge  
Top of Badge  
is on Left  
Door Frame Side  
Door Frame Side  
DOOR NAMEPLATE LOCATION  
To position nameplate:  
• Cut template along dotted line.  
• Hold or tape template behind glass  
door so that it is visible from the  
front side.  
• Remove backing from nameplate.  
• Place nameplate onto front side of  
door, matching illustration on the  
template.  
IMPORTANT: Nameplate must  
be placed on the opposite side of the  
door handle.  
Note: While performing installations described in this book,  
safety glasses or goggles should be worn.  
For Monogram® local service in your area, call  
1.800.444.1845.  
Note: Product improvement is a continuing endeavor at  
General Electric. Therefore, materials, appearance and  
specifications are subject to change without notice.  
GE Consumer & Industrial  
Pub. No. 31-46122-2  
Part No. 197D7840P001  
Appliances  
General Electric Company  
Louisville, KY 40225  
ge.com  
12-07 JR  
Printed in Slovenia  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eagle Tree Systems Stud Sensor GFORCE HIGH User Manual
EXP Computer Switch ThinConnect4 User Manual
Fellowes Paper Shredder FS 3 User Manual
Fender Stereo Amplifier Rumble 200 V3 User Manual
Fisher Price Mobility Aid H6372 User Manual
Frymaster Fryer FPH 14 User Manual
Fujitsu Network Card FPCAC14A User Manual
GarrettCom Switch Magnum 3000 User Manual
GE Microwave Oven 164D2966P127 I User Manual
Goodman Mfg Heat Pump GSH 10 SEER User Manual