®
Fujitsu LifeBook
T4220 Tablet PC
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
C o p y r i g h t
Copyright & Trademark Information
Macrovision Corporation and other rights users. Use of this
copyright protection technology must be authorized by
Macrovision Corporation, and is intended for home and
other limited viewing uses only unless authorized by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Fujitsu Computer Systems Corporation has made every
effort to ensure the accuracy and completeness of this
document. However, as ongoing development efforts are
continually improving the capabilities of our products, we
cannot guarantee the accuracy of the contents of this
document. We disclaim liability for errors, omissions, or
future changes.
All other trademarks mentioned herein are the property
of their respective owners.
Fujitsu, the Fujitsu logo, and LifeBook are registered
trademarks of Fujitsu Limited.
© Copyright 2007 Fujitsu Computer Systems Corporation.
All rights reserved. No part of this publication may be copied,
reproduced, or translated, without prior written consent of
Fujitsu Computer Systems Corporation. No part of this
publication may be stored or transmitted in any electronic
form without the written consent of Fujitsu Computer Systems
Corporation.
Microsoft, Windows, and Windows Vista are either trade-
marks or registered trademarks of Microsoft Corporation
in the United States and/or other countries.
PCMCIA is a trademark of the Personal Computer
Memory Card International Association.
Centrino, Intel, and Intel Core are trademarks or registered
trademarks of Intel Corporation or its subsidiaries in the
United States and other countries.
B5FJ-4091-01EN-00
WARNING
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Handling the cord on this product or cords
associated with accessories sold with this
product, will expose you to lead, a
chemical known to the State of California
to cause birth defects or other
Adobe, Acrobat, and Acrobat Reader are either registered
trademarks or trademarks of Adobe Systems Incorporated
in the United States and/or other countries.
The DVD player found in some models of the LifeBook
notebook incorporates copyright protection technology
that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by
reproductive harm.
Wash hands after handling.
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name:
Fujitsu Computer Systems Corporation
Address:
1250 E. Arques Avenue, MS 122
Sunnyvale, CA 94085
Telephone:
(408) 746-6000
Declares that product:
Model Configuration:
LifeBook T4220 Tablet PC
Complies with Part 15 of the FCC Rules.
This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:
(1) This device may not cause harmful interferences, (2) This device must accept any interference received,
including interference that may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
IMPORTANT SAFETY INSTRUCTIONS
This unit requires an AC adapter to operate. Use only
UL Listed Adapters with an output rating of 19 VDC,
with a current of 4.22 A.
For Authorized Repair Technicians Only
Danger of explosion if Lithium (clock) bat-
tery is incorrectly replaced. Replace only
with the same or equivalent type recom-
mended by the manufacturer. Dispose of
used batteries according to the manufac-
turer’s instruction.
AC Adapter output polarity:
+
For continued protection against risk of
fire, replace only with the same type and
rating fuse.
When using your notebook equipment, basic safety
precautions should always be followed to reduce the risk
of fire, electric shock and injury to persons, including
the following:
System Disposal
■
Do not use this product near water for example, near
a bathtub, washbowl, kitchen sink or laundry tub, in a
wet basement or near a swimming pool.
Avoid using the modem during an electrical storm.
There may be a remote risk of electric shock from
lightning.
Do not use the modem to report a gas leak in the
LAMP(S) INSIDE THIS PRODUCT
CONTAIN MERCURY AND MUST
BE RECYCLED OR DISPOSED OF
Hg
■
ACCORDING TO LOCAL, STATE, OR
FEDERAL LAWS.
■
vicinity of the leak.
Use only the power cord and batteries indicated in
■
this manual. Do not dispose of batteries in a fire. They
may explode. Check with local codes for possible
special disposal instructions.
■
To reduce the risk of fire, use only No. 26 AWG or
larger UL Listed or CSA Certified Telecommunication
Line Cord.
For TV tuner use: To protect from overvoltages and
■
transients on the Cable Distribution System, make
sure that the outer shield of the coaxial cable is
connected to earth (grounded) at the building premise
as close to the point of cable entrance as practicable, as
required per NEC Article 820.93, ANSI/NFPA 70:
2005. If you have questions about your CATV installa-
tion, contact your service provider.
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b l e o f C o n t e n t s
Fujitsu LifeBook® T4220 Series Tablet PC
Table of Contents
Keyboard
1
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . .20
Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . .20
PREFACE
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .20
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . .3
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Fujitsu Contact Information . . . . . . . . . . . . . . . . .3
Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . .21
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
LifeBook Security/Tablet PC Buttons
Security Button Functions. . . . . . . . . . . . . . . . . .22
2
Pre-logon button functions. . . . . . . . . . . . . . . . .22
Post-logon button functions. . . . . . . . . . . . . . . .24
GETTING TO KNOW
Changing Tablet PC Button Functions . . . . . . . .24
YOUR TABLET PC
Setting up LifeBook Security Panel . . . . . . . . . . .25
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Overview
Using Your LifeBook Security Panel . . . . . . . . . .25
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Uninstalling the Security Panel Application . . . . .26
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Locating the Controls and Connectors
Top and Front Components . . . . . . . . . . . . . . . .10
Left-Side Panel Components . . . . . . . . . . . . . . .12
Right-Side Panel Components . . . . . . . . . . . . . .13
Rear Panel Components . . . . . . . . . . . . . . . . . . .14
Bottom Components . . . . . . . . . . . . . . . . . . . . .15
Touchpad Pointing Device
Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . .27
Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Touchpad Control Adjustment . . . . . . . . . . . . . .28
Status Indicator Panel
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . .16
External Power Indicator. . . . . . . . . . . . . . . . . . .16
Battery Charging/Level Indicators. . . . . . . . . . . .16
Optical Drive Access Indicator . . . . . . . . . . . . . .17
Hard Drive Access Indicator . . . . . . . . . . . . . . . .17
NumLk Indicator. . . . . . . . . . . . . . . . . . . . . . . . .17
CapsLock Indicator. . . . . . . . . . . . . . . . . . . . . . .17
ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .17
Security Indicator . . . . . . . . . . . . . . . . . . . . . . . .17
Volume Control
Controlling the Volume . . . . . . . . . . . . . . . . . . .29
Pen and Active Digitizer
Using the Pen. . . . . . . . . . . . . . . . . . . . . . . . . . .30
Installing a Pen Tether . . . . . . . . . . . . . . . . . . . .30
Calibrating the Pen. . . . . . . . . . . . . . . . . . . . . . .31
Replacing the Pen Tip. . . . . . . . . . . . . . . . . . . . .31
Using the Active Digitizer . . . . . . . . . . . . . . . . . .31
Display Panel
Opening the Display Panel . . . . . . . . . . . . . . . . .18
Using the System as a Tablet . . . . . . . . . . . . . . .18
Adjusting Display Panel Brightness . . . . . . . . . . .19
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
Memory Stick/Secure Digital Media
Inserting Memory Stick/SD Cards . . . . . . . . . . . 50
Removing A Memory Stick/SD Card . . . . . . . . . 50
3
USING YOUR TABLET PC
Port Replicator
Power Sources
Connecting the Power Adapters. . . . . . . . . . . . . 35
Rear Panel Components. . . . . . . . . . . . . . . . . . . 51
Front Panel Components . . . . . . . . . . . . . . . . . . 52
Attaching the Port Replicator. . . . . . . . . . . . . . . 52
Detaching the Port Replicator . . . . . . . . . . . . . . 52
Power Management
Suspend/Resume Button . . . . . . . . . . . . . . . . . . 36
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Hibernate Mode. . . . . . . . . . . . . . . . . . . . . . . . . 37
Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . 37
Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . 37
Windows Power Management. . . . . . . . . . . . . . 37
Restarting the System. . . . . . . . . . . . . . . . . . . . . 37
Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Device Ports
Modem (RJ-11) Jack . . . . . . . . . . . . . . . . . . . . . 53
Internal LAN (RJ-45) jack. . . . . . . . . . . . . . . . . . 53
Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . 53
Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 54
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 54
External Video Port . . . . . . . . . . . . . . . . . . . . . . 54
External DVI Port. . . . . . . . . . . . . . . . . . . . . . . . 54
Starting Your Tablet PC
Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Boot Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . 39
Hard Disk Drive Passwords. . . . . . . . . . . . . . . . . 39
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . 39
Booting the System . . . . . . . . . . . . . . . . . . . . . . 40
Registering Your LifeBook Tablet PC . . . . . . . . . 40
Installing Click Me! . . . . . . . . . . . . . . . . . . . . . . 40
5
TROUBLESHOOTING
Identifying the Problem . . . . . . . . . . . . . . . . . . . 57
Specific Problems. . . . . . . . . . . . . . . . . . . . . . . . 57
Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 58
Power On Self Test Messages . . . . . . . . . . . . . . 65
Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 66
4
USER-INSTALLABLE FEATURES
Restoring Pre-installed Software
Re-Installing Drivers and Applications . . . . . . . . 67
Lithium ion Battery
Recharging the Battery. . . . . . . . . . . . . . . . . . . . 43
Restoring the Factory Image . . . . . . . . . . . . . . . 67
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 44
Memory Upgrade Module
6
Installing Memory Upgrade Modules . . . . . . . . . 45
Removing a Memory Upgrade Module . . . . . . . 46
Checking the Memory Capacity . . . . . . . . . . . . . 46
CARE AND MAINTENANCE
LifeBook T4220 Series Tablet PC . . . . . . . . . . . . 71
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Optional Floppy Disk Drive and Floppy Disks. . . 72
Optional Optical Drive and Discs . . . . . . . . . . . . 73
PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Flexible Bay Devices
Fujitsu Tablet Controls - CD/DVD Drive Help. . . 47
Removing and Installing Modular Devices . . . . . 48
PC Cards
Inserting PC Cards . . . . . . . . . . . . . . . . . . . . . . . 49
Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . 49
Smart Card Reader. . . . . . . . . . . . . . . . . . . . . . . 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b l e o f C o n t e n t s
Troubleshooting the WLAN
7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .103
SYSTEM SPECIFICATIONS
Wireless LAN Glossary
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Configuration Label . . . . . . . . . . . . . . . . . . . . . .77
Physical Specifications . . . . . . . . . . . . . . . . . . . .77
Processing Specifications . . . . . . . . . . . . . . . . . .77
Memory/Storage Specifications . . . . . . . . . . . . .77
Display Specifications . . . . . . . . . . . . . . . . . . . . .77
Interface Specifications. . . . . . . . . . . . . . . . . . . .77
Power Specifications. . . . . . . . . . . . . . . . . . . . . .78
Environmental Specifications . . . . . . . . . . . . . . .78
Agency Approval Specifications . . . . . . . . . . . . .79
Additional Specifications. . . . . . . . . . . . . . . . . . .79
IP address information
Additional Information . . . . . . . . . . . . . . . . . . .106
WLAN Specifications
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .108
Using the Bluetooth Device
What is Bluetooth?. . . . . . . . . . . . . . . . . . . . . .109
Where to Find Information About Bluetooth . .109
APPENDIX B: USING THE
FINGERPRINT SENSOR
8
GLOSSARY/REGULATORY
Fingerprint Sensor Device
Regulatory Information . . . . . . . . . . . . . . . . . . .82
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Introducing the Fingerprint Sensor Device . . . .113
Getting Started. . . . . . . . . . . . . . . . . . . . . . . . .113
Installing OmniPass . . . . . . . . . . . . . . . . . . . . .113
User Enrollment . . . . . . . . . . . . . . . . . . . . . . . .114
Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . .115
Configuring OmniPass . . . . . . . . . . . . . . . . . . .117
OmniPass Control Center. . . . . . . . . . . . . . . . .118
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .119
APPENDIX A: INTEGRATED
WIRELESS LAN USER’S GUIDE
Before Using the Wireless LAN
Wireless LAN Modes Using this Device. . . . . . . .94
Wireless Network Considerations . . . . . . . . . . . .95
Deactivating the WLAN Device . . . . . . . . . . . . .95
Activating the WLAN Device . . . . . . . . . . . . . . .96
Configuration of the WLAN Device
Flow of Operations. . . . . . . . . . . . . . . . . . . . . . .97
Configuration Using Wireless Zero Tool . . . . . . .97
Configuration Using Intel PROSet Software . . . .98
Configuration Using Atheros Client Utility . . . . .99
Connection to the network. . . . . . . . . . . . . . . .101
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Preface
1
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
2
Download from Www.Somanuals.com. All Manuals Search And Download.
P r e f a c e
FUJITSU CONTACT INFORMATION
Service and Support
You can contact Fujitsu Computer Systems Service and
Preface
Support the following ways:
ABOUT THIS GUIDE
The LifeBook® T4200 Series Tablet PC from Fujitsu
Computer Systems Corporation is a powerful convert-
ible computer. It can be used either as a standard note-
book using keyboard input, or in tablet configuration
using pen input. It is powered by a fast, Intel® Core™ 2
Duo processor, has a built-in color display with an active
digitizer, and brings the computing power of desktop
personal computers (PCs) to a portable and versatile
environment.
■
Toll free: 1-800-8Fujitsu (1-800-838-5487)
E-mail: [email protected]
Website:
■
■
http://www.computers.us.fujitsu.com/support
Before you place the call, you should have the following
information ready so that the customer support
representative can provide you with the fastest possible
solution:
■
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Type of device connected, if any
This manual explains how to operate your LifeBook
T4200 Series Tablet PC’s hardware and built-in system
software. Your LifeBook T4200 Series Tablet PC comes
with Windows® XP Tablet PC Edition 2005 or Windows
Vista™ Business pre-installed.
■
■
■
■
■
Your LifeBook T4200 Series Tablet PC is a completely
self-contained unit with an active-matrix (TFT) color
LCD display. The display has a wide viewing angle and
can be used indoors or outdoors. The tablet has a
powerful interface that enables it to support a variety of
optional features.
■
Fujitsu Online
You can go directly to the online Fujitsu Product catalog
for your LifeBook notebook by going to:
www.shopfujitsu.com.
You can also reach Fujitsu Service and Support online by
clicking on the Service and Support Website URL link,
located in the Fujitsu Web links -> Service and Support
Software folder of the Windows Start menu.
Conventions Used in the Guide
Keyboard keys appear in brackets.
Example: [Fn], [F1], [Esc], [Enter] and [Ctl].
Pages with additional information about a specific topic
are cross-referenced within the text.
Example: (See page xx.)
You must have an active internet
connection to use the online URL links.
On screen buttons or menu items appear in bold.
Example: Click OK to restart your Tablet PC.
WARRANTY
The information icon highlights
Your LifeBook T4200 Series Tablet PC is backed by an
International Limited Warranty and includes toll-free
technical support. Check the service kit that came with
your Tablet PC for warranty terms and conditions.
information that will enhance your
understanding of the subject material.
The caution icon highlights information
that is important to the safe operation of
your computer, or to the integrity of your
files. Please read all caution information
carefully.
The warning icon warns you about
possible hazards that can occur to you,
your system, or your files. Please read all
warning information carefully.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
P r e f a c e
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting to Know
Your Tablet PC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
6
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Figure 2-1. Fujitsu LifeBook T4200 Series Tablet PC
You may also have one or more of the following devices
in the box, depending upon the configuration of your
system:
Overview
This section describes the components of your Fujitsu
LifeBook T4200 Series Tablet PC. We strongly recom-
mend that you read it before using your Tablet PC, even
if you are already familiar with mobile computers.
■
Port Replicator (Figure 2-3)
External USB Floppy Disk Drive
Additional battery(s)
Application CD(s) for third-party software
■
■
■
UNPACKING
For the latest list of accessories available for your Life-
Book T4200 Series Tablet PC, be sure to frequently
check the Fujitsu Website at: www.shopfujitsu.com.
When you receive your LifeBook T4200 Series Tablet
PC, unpack it carefully, and compare the parts you have
received with the items listed below.
For a pre-configured model you should have:
■
LifeBook T4200 Series Tablet PC (Figure 2-1)
AC adapter with AC power cord (Figure 2-2)
Pen Kit (including one pen, five extra pen tips, and
■
■
one tip replacement tool)
Pen tether
Screen protectors (Qty. 2)
Driver and Application Restore (DAR) DVD
Recovery DVD
Getting Started Guide
User’s Guide (this document)
International Limited Warranty Booklet
■
■
■
■
Figure 2-2. AC Adapter
■
■
■
■
Certificate of Authenticity
Lithium ion battery (pre-installed)
■
Figure 2-3. Optional Port Replicator
7
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n
2
Locating the Controls and Connectors
Connectors and peripheral interfaces on the LifeBook
T4200 Series Tablet PC and the optional port replicator
allow you to connect a variety of devices. Specific loca-
tions are illustrated in Figures 2-4 through 2-8. The
table below provides a short description of each icon on
the LifeBook T4200 Series Tablet PC and/or optional
port replicator. Each of the icons is either molded into
or printed on the Tablet PC or port replicator chassis.
Tablet PC
Connection
Icon
Purpose
DC in connector
Connect an external power source such as the AC adapter or auto/
airline adapter.
SD/Memory
Stick Slot
The Secure Digital (SD) card/Memory Stick slot allows you to insert
a flash memory card for data storage. Flash memory cards allow
you to transfer data to and from a variety of different digital
devices.
Smart Card Slot
The dedicated Smart Card slot allows you to insert a Smart Card on
which you can store such data as medical information or electronic
“cash”.
USB Port
Connect Universal Serial Bus 2.0 or 1.1 compliant devices to the
Tablet PC.
PCMCIA Card slot
Insert Type I or Type II PC Cards.
Microphone/line-in
jack
Connect an external microphone. The internal microphone is
disabled when you plug in an external microphone.
Headphone/
line-out jack
Connect stereo headphones or powered external speakers. The
internal speaker is disabled when you plug in external headphones
or powered speakers.
IrDA/FIR port
An infrared transceiver built into the Tablet PC allows you to
communicate with other devices that are compliant with IrDA
Standard Rev. 1.1. Effective range for infrared communication is
about 3 feet, and within 15 degrees off center. A clear line-of-sight
path must exist between the IrDA port on the computer and the
IrDA transceiver on the other device.
Modem
Connect a telephone line to the internal modem using a standard
RJ-11 telephone plug.
Tablet Dock port
Connect the Tablet PC port replicator or other approved docking
device. Refer to documentation accompanying the dock for more
information.
Security lock slot
The security slot allows you to secure the Tablet PC using
compatible locking devices.
Suspend/Resume
button
The Suspend/Resume button allows you to suspend Tablet PC
activity without powering off, resume your Tablet PC from suspend
mode, and power on the system when it has been shut down from
Windows.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Tablet PC
Icon
Connection
Local Area
Purpose
The LAN (RJ-45) jack is used to connect the internal 10/100/1000*
Base-T/Tx Ethernet to a Local Area Network (LAN) in your office or
home, or broadband devices such as a cable modem, DSL, or satellite
Internet.
Network (LAN)
*1000 Mbps, commonly referred to as Gigabit Ethernet.
Wireless LAN
On-Off Switch
The wireless LAN switch allows you to turn power to the optional
wireless LAN device on and off.
Display Rotation
This two-part light indicates the direction in which the display
should be rotated when converting back to notebook mode.
Depending upon which direction the display was rotated, either the
top or bottom indicator will light to indicate which direction to turn
the display to return to notebook mode.
ROTATE
External Video port
The external video port allows you to connect an external monitor
or LCD projector to your computer.
Table 2-1. System icons
9
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n
2
Display
Panel
Latch
Built-in Microphone
Pen/
Pen Holder
Display
Panel
Status Indicator Panel
Fingerprint Sensor
Built-in
Microphone
LifeBook
Security/
Tablet PC
Buttons
Display Rotation Indicator
Rotation Hinge
Power
Indicator
SD/Memory
Stick Slot
Suspend/
Resume
Button
Stereo Speaker
Keyboard
Headphone
Jack
Display Panel
Release Button
Stereo Speaker
Microphone
Touchpad Pointing Device
Jack
Figure 2-4. LifeBook T4200 Series Tablet PC with display open
Power Indicator
TOP AND FRONT COMPONENTS
The power indicator shows the power state of the system.
Solid blue indicates that power is on, and blinking green
indicates that the system is in suspend mode.
The following is a brief description of the top and front
features of the LifeBook T4200 Series Tablet PC.
Built-in Microphones
Suspend/Resume Button
The built-in microphones allow you to input mono
The Suspend/Resume button allows you to suspend
Tablet PC activity without powering off, resume your
Tablet PC from standby mode, and power on your
system when it has been shut down from the Windows
operating system. See “Power On” on page 39.
audio.
Display Panel Latch
The display panel latch locks and releases the display
panel.
Display Panel
Keyboard
The display panel is a color LCD panel with back lighting
for the display of text and graphics and active digitizer
functionality.
A full-function keyboard with dedicated Windows keys.
See “Keyboard” on page 20.
Touchpad Pointing Device
LifeBook Security/Tablet PC Buttons
The Touchpad pointing device consists of two mouse-
like buttons and one scroll button. See “Touchpad
Pointing Device” on page 27.
The LifeBook T4200 Series Tablet PC Security/Tablet PC
Buttons provide hardware security and application
launch capabilities. See “LifeBook Security/Tablet PC
Buttons” on page 22.
Stereo Speakers
The stereo speakers allow you to listen to stereo sound
from your system.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Display Panel Release Button
The display panel release button allows you to release
the display so that it can be opened.
Microphone Jack
The microphone jack allows you to connect an external
mono microphone. See “Microphone Jack” on page 54.
Headphone Jack
The headphone jack allows you to connect stereo head-
phones or powered external speakers. See “Headphone
Jack” on page 54.
SD Card/Memory Stick
The Secure Digital (SD) card/Memory Stick slot allows
you to insert a flash memory card for data storage. Flash
memory cards allow you to transfer data to and from a
variety of different digital devices.
Rotation Hinge
The rotation hinge allows you to transform your Tablet
PC from a notebook configuration into a tablet configu-
ration. See “Using the System as a Tablet” on page 18.
Fingerprint Sensor
The fingerprint sensor device allows you to log onto
your system and password-protected websites and appli-
cations by swiping your finger over the sensor. See
“Fingerprint Sensor Device” on page 113.
Status Indicator Panel
The Status Indicator Panel displays symbols that corre-
spond to specific components of your LifeBook T4200
Series Tablet PC. See “Status Indicator Panel” on
page 16.
Pen/Pen Holder
The pen is used as the interface with the active digitizer
display.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n
2
Pen Tether Attachment Point
Air Vents
PC Card Slot
USB 2.0 Port
Smart Card Slot
PC Card Eject/
Lock Button
Wireless LAN/Bluetooth On/Off Switch
DC Power Jack
Figure 2-5. LifeBook T4200 Series Tablet PC left-side panel
WLAN/Bluetooth On/Off Switch
The wireless LAN/Bluetooth On/Off Switch is used to
power off the wireless radio(s) when not in use.
LEFT-SIDE PANEL COMPONENTS
Following is a brief description of your Tablet PC’s left-
side components. (Figure 2-5)
Smart Card Slot
Pen Tether Attachment Point
The dedicated Smart Card slot allows you to insert an
optional Smart Card that can be used for user authenti-
cation with an encrypted password. A Smart Card can
also be used to store and access personal data, such as
medical information or electronic “cash”.
The pen tether attachment point is designed to securely
hold a pen tether to prevent loss of the pen. See
“Installing a Pen Tether” on page 30 for additional infor-
mation.
Air Vents
The air vents are used to cool the system to prevent over-
heating.
To protect your computer from damage
and to optimize system performance, be
sure to keep all air all vents unobstructed,
clean, and clear of debris. This may
require periodic cleaning, depending upon
the environment in which the system is
used.
Do not operate the computer in areas
where the air vents can be obstructed,
such as in tight enclosures or on soft
surfaces like a bed or cushion.
PC Card Slot
The PC Card Slot allows you to insert a Type I or Type II
PC Card. The PC Card Eject Button is used when
ejecting a PC Card from the slot. See “PC Cards” on
page 49.
DC Power Jack
The DC power jack allows you to plug in the AC adapter
or the optional Auto/Airline adapter to power your
Tablet PC and charge the internal Lithium ion Battery.
USB 2.0 Port
The three USB 2.0 ports (two on rear panel and one on
left-side panel) allow you to connect Universal Serial Bus
devices. See “Universal Serial Bus Ports” on page 53.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Flexible Bay
Anti-theft Lock Slot
Anti-theft Lock Slot
Flexible Bay Eject Lever
Figure 2-6. LifeBook T4200 Series Tablet PC right-side panel
RIGHT-SIDE PANEL COMPONENTS
Following is a brief description of your Tablet PC’s
right-side components.
Anti-theft Lock Slots
The anti-theft lock slots allows you to attach a optional
physical lock-down device to secure your computer.
Flexible Bay
The Flexible Bay can accommodate one of the following
devices. See “Flexible Bay Devices” on page 47.
■
Modular DVD/CD-RW combo drive
Modular Dual-Layer Multi-Format DVD Writer
Modular DVD-ROM drive
Modular 2nd hard disk drive
Modular Lithium ion battery
Weight Saver
■
■
■
■
■
Flexible Bay Eject Lever
The Flexible Bay eject lever releases the Flexible Bay
device.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n
2
Modem (RJ-11) Port
(under cover)
Infrared Port
USB 2.0 Port
LAN (RJ-45) Port
(under cover)
External Video
Port (under cover)
USB 2.0 Port
Figure 2-7. LifeBook T4200 Series Tablet PC rear panel
USB 2.0 Ports
REAR PANEL COMPONENTS
The three USB 2.0 ports (two on rear panel and one on
left-side panel) allow you to connect Universal Serial Bus
devices. See “Universal Serial Bus Ports” on page 53.
Modem (RJ-11) Telephone Port
The Modem (RJ-11) telephone port is for attaching
a telephone line to the internal multinational 56K
modem.
Infrared Port
The fast IrDA compatible port allows you to communi-
cate with another IrDA-compatible infrared device
without a cable. (See “Infrared Port” on page 53.)
The internal multinational modem is not
intended for use with Digital PBX systems.
Do not connect the internal modem to a
Digital PBX as it may cause serious damage
to the internal modem or your entire
LifeBook T4200 Series Tablet PC. Consult
your PBX manufacturer’s documentation
for details. Some hotels have Digital PBX
systems. Be sure to find out BEFORE you
connect your modem.
LAN (RJ-45) Port
The internal LAN (RJ-45) port is used for an internal
GigaLAN Ethernet (10/100/1000 Base-T/TX) connec-
tion. See “Internal LAN (RJ-45) jack” on page 53.
External Video Port
The external video port allows you to connect an
external monitor or LCD projector. For simultaneous
display, this model supports XGA (max. 1024 x 768)
resolution. When running external display only, UXGA
(max 1600 x 1200 resolution) is supported. When in
extended desktop mode, simultaneous XGA on the LCD
display and SXGA on the external display is supported.
Note that when the optional Port Replicator is attached
to the system, you must use the external monitor port on
the Port Replicator rather than the port on the system.
See “External Video Port” on page 54.
The internal modem is designed to the
ITU-T V.90 standard. Its maximum speed
of 53000 bps is the highest allowed by
FCC, and its actual connection rate
depends on the line conditions. The
maximum speed is 33600 bps at upload.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Port Replicator
Connector
Memory
Upgrade
Compartment
Main Unit and
Configuration
Label (approximate
location)
Battery
Pack Latch
Lithium ion
Battery
Compartment
Air Vents
(various locations)
Battery
Pack Latch
Figure 2-8. LifeBook T4200 Series Tablet PC bottom panel
Air Vents
BOTTOM COMPONENTS
The air vents are used to cool the system to prevent over-
Following is a brief description of your Tablet PC’s
heating.
bottom panel components. (Figure 2-8)
Lithium ion Battery Compartment
To protect your computer from damage
and to optimize system performance, be
sure to keep all air all vents unobstructed,
clean, and clear of debris. This may
require periodic cleaning, depending upon
the environment in which the system is
used.
The battery compartment contains the internal Lithium
ion battery. The battery should be removed when the
computer is stored over a long period of time or for
swapping a discharged battery with a charged Lithium
ion battery. See “Lithium ion Battery” on page 43.
Port Replicator Connector
This connector allows you to connect the optional port
replicator.
Do not operate the computer in areas
where the air vents can be obstructed,
such as in tight enclosures or on soft
surfaces like a bed or cushion.
Main Unit and Configuration Label
The configuration label shows the model number and
other information about your LifeBook T4200 Series
Tablet PC. In addition, the configuration portion of the
label has the serial number and manufacturer informa-
tion that you will need to give your support representa-
tive. It identifies the exact version of various
components of your Tablet PC.
Memory Upgrade Compartment
Your Tablet PC comes with high speed DDR2 Synchro-
nous Dynamic RAM (SDRAM). The memory upgrade
compartment allows you to expand the system memory
capacity of your Tablet PC, hence improving overall
performance. See “Memory Upgrade Module” on
page 45.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
1
A
1
2
Battery 1
Charging
Wireless
LAN On
Battery 2
Charging
Battery 1
Level
Hard Drive
Access
Power
CapsLk
Security
Indicator
External
Power
Battery 2
Level
Optical
Drive Access
NumLk
ScrLk
Figure 2-9. Status Indicator Panel
EXTERNAL POWER INDICATOR
The external power indicator states whether your tablet
is operating from the AC adapter, the auto/airline
adapter or the batteries. This icon has two different
states that can tell you what power source your LifeBook
Tablet PC is using.
Status Indicator Panel
The Status Indicator Panel displays symbols that corre-
spond to specific components of your LifeBook T4200
Series Tablet PC. These symbols tell you how each of
those components is operating. (Figure 2-9)
■
On: This means that either of the adapters are
currently in use.
Off: Power is only coming from the batteries, and you
do not have an adapter connected.
POWER INDICATOR
■
The Power indicator symbol states whether your system
is operational. It has several different states, each of
which tells you what mode your Tablet PC is in at that
time.
BATTERY CHARGING/
1
■
Steady On: This means that there is power to your
Tablet PC and that it is ready for use.
LEVEL INDICATORS
The Battery Charging and Battery Level indicators state
whether the Lithium ion battery (Battery 1) or the
optional modular battery (Battery 2) are installed and
charging, and how much charge is available within the
batteries. (Figure 2-10)
■
Flashing: This means that your Tablet PC is in
Standby mode.
■
Steady Off: This means that your system is either in
Hibernate mode, or that your Tablet PC has been
turned off.
Additionally, these indicators display when an over-
current is detected. If an overcurrent is detected, the
battery stops charging and the Battery Level indicator
blinks at the rate of once per second. To stop the indi-
cator from blinking, you must disconnect the power
If you are charging your battery, the Power indicator
symbol will remain on even if your LifeBook T4200
Series Tablet PC is shut off. The Power indicator symbol
will also remain on if you have either adapter connected
and are shut down from Windows.
adapter.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Batteries subjected to shocks, vibration or
extreme temperatures can be permanently
damaged.
OPTICAL DRIVE ACCESS INDICATOR
The Optical Drive Access indicator states whether your
internal optical drive is being accessed.
HARD DRIVE ACCESS INDICATOR
The Hard Drive Access indicator states whether your
internal hard drive is being accessed.
76%–100% Charging
76%–100%
51%–75%
NUMLK INDICATOR
The NumLk indicator states that the integral keyboard is
26%–50%
set in ten-key numeric keypad mode.
11%–25%
Low Warning <11%
CAPSLOCK INDICATOR
The CapsLock indicator states that your keyboard is set
to type in all capital letters.
Critical Low or
Dead Battery
Shorted Battery
SCRLK INDICATOR
Figure 2-10. Battery Level Indicator
The ScrLk indicator states that your scroll lock is active.
A shorted battery is damaged and must be
replaced. (Figure 2-10)
SECURITY INDICATOR
The Security Indicator flashes (if a password was set)
when the system resumes from Off or Standby modes.
You must enter the password that was set in the Security
Panel before your system will resume operation.
If there is no battery activity and the
power adapters are not connected, the
Battery Level indicators will also be off.
WIRELESS LAN/BLUETOOTH
ON INDICATOR
The Wireless LAN/Bluetooth On indicator is displayed
when the switch for the optional internal Wireless LAN/
Bluetooth device is switched on.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
Display
Panel
Latch
Latch
Release
Button
Figure 2-11. Opening the display
2. When the display is perpendicular to the keyboard,
rotate it 180 degrees in either direction (Figure 2-15)
so that it is facing backwards. (Figure 2-16)
Display Panel
Your LifeBook T4200 Series Tablet PC contains a display
panel that is backlit for easier viewing in bright environ-
ments. The convertible design of your Tablet PC allows
you to open the display fully, rotate it in either direction
180 degrees, and lay it face up on the keyboard. This
allows you to use the system as a tablet, much as you
would a pad of paper.
3. Holding the top edge of the display panel, pull it
forward until it is lying nearly atop the keyboard.
4. Push the latch towards the display (See “A” in
Figure 2-12). The latch will pivot so the top latch
disappears, and the bottom latch appears (See “B” in
Figure 2-12). Holding the latch down, lay the display
flush against the system so that the latch engages.
You can now use your system as a tablet. (Figure 2-
17)
OPENING THE DISPLAY PANEL
1. Press the latch release button. This releases the
locking mechanism. While holding the latch release,
lift display cover.
A
Display Side
2. Lift the display backwards, being careful not to
touch the screen with your fingers, until it is at a
comfortable viewing angle. (Figure 2-11)
Top latch
USING THE SYSTEM AS A TABLET
If you would like to use the system as a tablet, perform
Bottom latch
the following steps.
B
The display can be rotated in either
direction, but when returning the system
to notebook mode, be sure to observe the
display rotation light. Rotate the system
display only in the direction indicated by
the light. Turning the display in the
incorrect direction could cause hinge
damage.
Figure 2-12. Latching/Unlatching
5. To return the system to notebook configuration,
repeat step 3 and 2. Be sure to turn the display in the
direction indicated by the display rotation light
(Figure 2-13).
In the following step, be sure to position
the display perpendicular to the keyboard,
otherwise the keyboard or display cover
could get scratched.
ROTATE
1. Lift the display until it is perpendicular to the
Figure 2-13. Display rotation light
keyboard. (Figure 2-14).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
90o
Figure 2-17. System in tablet configuration
ADJUSTING DISPLAY PANEL BRIGHTNESS
Once you have turned on your Tablet PC, you may want
to adjust the brightness level of the screen to a more
comfortable viewing level. There are three ways to adjust
the brightness, keyboard, power management utility,
and Fujitsu Menu.
Display rotation light
Figure 2-14. Fully open display
Using Keyboard to Adjust Brightness
Adjusting the brightness using the keyboard changes the
system setting (i.e., the settings you make via the func-
tion keys automatically changes the brightness settings
in the system’s Pen and Tablet Settings).
■
[Fn+F6]: Pressing repeatedly will lower the brightness
of your display.
■
[Fn+F7]: Pressing repeatedly will increase the
brightness of the display.
Using Power Management to Adjust Brightness
To adjust brightness with the power management utility,
click Start -> Control Panel -> Tablet and Pen Settings
(Windows XP) or Tablet PC Settings (Windows Vista).
Select the Display tab and set the screen brightness slider
for battery and AC power scenarios.
Figure 2-15. Rotating the display
Using the Fujitsu Menu to Adjust Brightness
To adjust brightness using the Fujitsu menu, click on the
Fujitsu Menu icon in the system tray in the lower right
corner of the screen (or double-click the Function
button). From the menu that appears, select Brightness
Control. The Tablet and Pen Settings window will open.
Figure 2-16. Display rotated completely
19
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
Select the Display tab and set the screen brightness slider
for battery and AC power scenarios.
If using AC power, your brightness setting
is set to its highest level by default. If using
battery power, your brightness settings is
set to approximately mid-level by default.
The higher the brightness level, the more
power the Tablet PC will consume and the
faster your batteries will discharge. For
maximum battery life, make sure that the
brightness is set as low as possible.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
Function Keys
End
Home
Numeric Keypad
(outlined with thick
black line)
Fn Key
Start Key
Cursor Keys
Application Key
Figure 2-18. Keyboard
NUMERIC KEYPAD
Keyboard
Certain keys on the keyboard perform dual functions as
both standard character keys and numeric keypad keys.
NumLk can be activated by pressing the [NumLk] key.
Turning off the NumLk feature is done the same way.
Once this feature is activated you can enter numerals 0
through 9, perform addition ( + ), subtraction ( - ),
multiplication ( * ), or division ( / ), and enter decimal
points ( . ) using the keys designated as ten-key function
keys. The keys in the numeric keypad are marked on the
front edge of the key to indicate their secondary func-
tions. (Figure 2-18)
USING THE KEYBOARD
Your LifeBook T4200 Series Tablet PC has an integral
84-key keyboard. The keys perform all the standard
functions of a 101-key keyboard, including the Windows
keys and other special function keys. This section
describes the following keys. (Figure 2-18)
■
Numeric keypad: Your Tablet PC allows certain keys
to serve dual purposes, both as standard characters
and as numeric and mathematical keys. The ability to
toggle between the standard character and numerical
keys is controlled through the [NumLk] key.
WINDOWS KEYS
Your LifeBook T4200 Series Tablet PC has two Windows
keys: a Start key and an Application key. The Start key
displays the Start menu. This button functions the same
as your onscreen Start menu button. The Application
key functions the same as your right mouse button and
displays shortcut menus for the selected item. (Please
refer to your Windows documentation for additional
information regarding the Windows keys.) (Figure 2-18)
■
Cursor keys: Your keyboard contains four arrow
keys for moving the cursor or insertion point to the
right, left, up, or down within windows, applications
and documents.
■
Function keys: The keys labeled [F1] through [F12],
are used in conjunction with the [Fn] key to produce
special actions that vary depending on what program
is running.
■
Windows keys: These keys work with your Windows
CURSOR KEYS
operating system and function the same as the
onscreen Start menu button, or the right button on
your pointing device.
The cursor keys are the four arrow keys on the keyboard
which allow you to move the cursor up, down, left, and
right in applications. In programs such as Windows
Explorer, it moves the “focus” (selects the next item up,
down, left, or right). (Figure 2-18)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
FUNCTION KEYS
Your Tablet PC has 12 function keys, F1 through F12.
The functions assigned to these keys differ for each
application. You should refer to your software docu-
mentation to find out how these keys are used.
(Figure 2-18)
[Fn] Key
The [Fn] key provides extended functions for the
Tablet PC and is always used in conjunction with
another key.
■
[Fn+F3]: Pressing [F3] while holding [Fn] will toggle
the Audio Mute on and off.
■
[Fn+F4]: Pressing [F4] while holding [Fn] will toggle
the built-in pointing device on and off.
■
[Fn +F5]: Pressing [F5] while holding [Fn] allows
you to toggle between video compensation and no
compensation. (Video compensation controls spacing
on the display. When it is enabled, displays with lower
pixel resolution will still cover the entire screen.)
■
[Fn+F6]: Pressing [F6] repeatedly while holding [Fn]
will lower the brightness of your display. Note that
adjusting the brightness using the keyboard changes
the system setting.
■
[Fn+F7]: Pressing [F7] repeatedly while holding [Fn]
will increase the brightness of the display.
■
[Fn+F8]: Pressing [F8] repeatedly while holding [Fn]
will decrease the volume of your Tablet PC.
■
[Fn+F9]: Pressing [F9] repeatedly while holding [Fn]
will increase the volume of your Tablet PC.
■
[Fn+F10]: Pressing [F10] while holding [Fn] allows
you to change your selection of where to send your
display video. Each time you press the combination of
keys you will step to the next choice. The choices, in
order, are: built-in display panel only, both built-in
display panel and external monitor, or external moni-
tor only.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
ENT
(2) Application B Button
(1) Application A Button
(4) Button 4
(3) Button 3
Enter Button
Figure 2-19. LifeBook T4200 Series Tablet PC Security/Tablet PC Buttons
LifeBook Security/Tablet PC Buttons
A unique feature of your LifeBook T4200 Series Tablet
PC is the array of Security and Tablet PC buttons. These
buttons allow you to secure your Tablet PC from unau-
thorized use and to launch specific applications and
functions with the touch of a button.
PRE-LOGON BUTTON FUNCTIONS
All five buttons can be used before logging on to
Windows (i.e., the Windows logon screen is displayed).
Three of the buttons have secondary functions. See
Table 2-3 for information about each of the pre-logon
functions.
SECURITY BUTTON FUNCTIONS
<Tab>/<Shift><Tab>
If the security system is activated, upon starting your
Tablet PC or resuming from Standby, Hibernate, or shut-
down mode, the security system will require you to enter
a password code using the security buttons. After you
enter the correct password, your system will resume
operation.
When you press the Page Down button when the system
is pre-logon, each press of the button will act as if you
had pressed the [Tab] key.
When you press the Fn button then press and release the
Page Down button, each press of the button will act as if
you had pressed the [Shift]+[Tab] key combination.
The five security/Tablet PC buttons are located on the
bottom right-hand side of the display when it is config-
ured to be used as a notebook.
<Enter>/<Escape>
When you press the Page Up button when the system is
pre-logon, each press of the button will act as if you had
pressed the [Enter] key.
All five buttons are used when implementing security
functions. Four of the buttons are used to enter the pass-
word, and the fifth is used as an Enter button. See Table
2-2 for information about each of the Security buttons.
Button Icon
System State
Security Panel Function
Security Button 1
System is pre-boot or
resuming from suspend
Security Button 2
Security Button 3
Security Button 4
Security Enter Button
Table 2-2. Security Panel Button Functions
22
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Secondary Functions
Button Icon
System State
Tablet PC Function
(Fn + Button)
System is pre-logon
(Windows logon
<Tab>
<Shift><Tab>
screen is displayed)
<Enter>
<Escape>
None
Rotate screen
Used to invoke secondary
function
None
None
Ctl+Alt+Del Button
Table 2-3. Pre-logon Tablet PC Button Functions
When you press the Fn button then press and release the
Page Up button, each press of the button will act as if
you had pressed the [Escape] key.
The screen orientation default can be
changed by going to the Control Panel and
double-clicking on the Fujitsu Tablet
Controls icon and selecting the desired
settings in the display properties. After
changing the settings, save them in Fujitsu
Tablet Controls.
Screen Rotation
The screen rotation feature would normally be used
when the system is configured as a tablet. When you
would like to use the tablet as an eBook, for example,
you would use the portrait orientation; when accessing
spreadsheets or using the system as a notebook, you
would more typically use landscape orientation.
When you press the Screen Rotation button when the
system is in pre-boot, the system screen orientation
changes from portrait (vertical) to landscape (hori-
zontal) or from landscape to portrait.
When the system is changed to tablet configuration, the
orientation automatically changes to portrait mode by
default.
Secondary Functions
Button Icon
System State
Primary Tablet PC Function
(Fn + Button)
System is post-logon
(Windows desktop is
displayed)
User-defined Application A
(Default = Calculator)
Page Down
Page Up
User-Defined Application B
(Default = MS Journal)
Display Switching:
1. LCD only
Screen Rotation
2. CRT only
3. Dual Display
Secondary Function Selection
Ctl+Alt+Del Button
Fujitsu Menu Utility
None
Table 2-4. Post-logon Tablet PC Button Functions
23
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
Function / Fujitsu Menu Utility Button
When you press the Screen Rotation /Display Switching
button, the system screen orientation changes from
portrait (vertical) to landscape (horizontal) or from
landscape to portrait.
The Function button works in conjunction with the
other application buttons to provide additional func-
tionality for the buttons. Refer to specific details above.
Pressing the Fn button with while pressing the Screen
Rotation button will switch the display output in the
following order: LCD only, CRT only, dual display.
POST-LOGON BUTTON FUNCTIONS
All five buttons can be used after logging on to
Windows. Four of the buttons have secondary functions.
See Table 2-4 for information about each of the post-
logon functions.
Function / Fujitsu Menu Utility Button
The Function button works in conjunction with the
other application buttons to provide additional func-
tionality for the buttons. Refer to specific details above.
Page Down / Application A Button
When you press the Page Down button when the system
is running, each press of the button will scroll the screen
down one frame. This allows you to navigate quickly
through large documents.
Pressing the Fn button twice in succession causes the
Fujitsu Menu Utility to appear on your screen, allowing
you to modify certain system settings.
Ctl+Alt+Del Button
When you press the Fn button then press and release the
Page Down/Application A button, you will automati-
cally start whichever program is assigned to the button.
The default application for this button is Calculator. See
“Changing Tablet PC Button Functions” on page 24 to
select a different application for this button.
Pressing and holding the Ctl-Alt-Del button for up to
750 milliseconds launches the Logon screen or the
Windows Task Manager (if the system hasn’t yet been
configured).
CHANGING TABLET PC
BUTTON FUNCTIONS
The Application A and B buttons can be changed to
launch a program or perform an action you select. By
default, the Application A button launches the Calcu-
lator, and the Application B button launches MS
Journal.
Page Up / Application B Button
When you press the Page Up button when the system is
running, each press of the button will scroll the screen
up one frame. This allows you to navigate quickly
through large documents.
When you press the Fn button then press and release the
Page Up/Application B button, you will automatically
start whichever program is assigned to the button. The
default application for this button is Microsoft Journal.
See “Changing Tablet PC Button Functions” on page 24
to select a different application for this button.
To launch different applications or cause the Applica-
tion A or B buttons to perform a specific action:
1. Double-click on the Tablet and Pen Settings icon in
the Control Panel.
2. Select the Tablet Buttons tab and select the button
you would like to change from the list.
Screen Rotation /Display Switching Button
The screen rotation feature would normally be used
only when the system is configured as a tablet. When
you would like to use the tablet as an eBook, for
example, you would use the portrait orientation; when
accessing spreadsheets or using the system as a note-
book, you would more typically use landscape orienta-
tion.
3. Click [Change] and open the drop down list in the
Action: field.
4. Select the action you would like the button to
perform. If you want to launch a program, click on
Launch an Application then browse to the location
of the program.
5. Click [OK], then click [OK] again. The buttons will
now perform the actions you have assigned to them.
When the system is changed to tablet configuration, the
orientation automatically changes to portrait mode by
default.
The screen orientation default can be
changed by going to the Control Panel and
double-clicking on the Fujitsu Tablet
Controls icon and selecting the desired
settings in the display properties. After
changing the settings, save them in Fujitsu
Tablet Controls.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
2. Click on Run.
SETTING UP LIFEBOOK SECURITY PANEL
When you receive your Tablet PC, the security panel
application is pre-installed without any passwords. The
following sections provide detailed information on your
security panel, how to set, change or remove passwords.
3. Type in: C:\Program
Files\Fujitsu\Security Panel
Application\Supervisor\ FJSECS.EXE,
then press [Enter]
4. Follow the on-screen instructions to set the Super-
visor password.
Numbered Buttons
Use these buttons to enter your password.
Setting User Password
Enter Button
After entering the button strokes, push this button to
enter the password into the Tablet PC.
1
Go to the Start menu.
2. Click on All Programs.
3. Click on Security Panel Application -> Security
Panel Application.
PASSWORDS
4. Follow the on-screen instructions to set the user
password.
The user and supervisor password may be set on this
Tablet PC. A supervisor password is typically the same
for all tablets and notebooks in a work group, office, or
company to allow for system management. Individual
computers in a group environment should not use a
common password. A password consists of one to five
button strokes plus the enter button. A valid stroke
consists of pushing one or up to four buttons simulta-
neously.
You may change or remove the supervisor
or user password by repeating the steps
defined above.
USING YOUR LIFEBOOK SECURITY PANEL
The security lock feature is in effect both when the system
resumes from Off, Standby, or Hibernation state. You
always need to push the Security Panel buttons to input
the user password. Your system will not begin the boot
sequence until you enter your supervisor/user password.
The following are valid button strokes:
■
Pushing [4] by itself
Pushing [2] and [3] at the same time
Pushing [1], [2], and [4] at the same time
Pushing [1], [2], [3], and [4] at the same time
■
■
■
The following are valid passwords. The numbers within
braces ({ }) are button strokes using more than one
button.
From Off State
1. Turn on your system.
2. When the Security Indicator flashes, enter the pass-
word and press Enter button (e.g., if the password is
22222, first press Button 2 five times, then press the
Enter button). The Tablet PC will boot to normal
operation.
■
{[2]+[3]}, [1], [Enter]
[4], [enter]
{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]
■
■
Setting Passwords
When shipped from the factory, no passwords are set.
You have a choice of having no password or setting a
supervisor and user password. You must set the super-
visor password before the user password.
From Standby/Hibernation State
1. Press your Suspend/Resume button.
2. When the Security Indicator flashes, enter the pass-
word and press Enter button.
The Tablet PC should resume normal operation.
• The purpose of supervisor password is
to be able to bypass the user password
in case the user password is forgotten.
The supervisor password alone will not
lock the system.
• You must set the supervisor and user
passwords for the security panel to
work.
Incorrect Password Entry
If an invalid supervisor or user password is entered three
times in succession, the system will “beep” for about one
minute. If a valid password is entered within a minute
(while system beeps), the beeping will stop and the
Tablet PC will resume normal operation. If no password
is entered or an invalid password is entered while the
system beeps, the system will return to its previous
locked state (standby or off) and the Security Indicator
will go off. To reactivate the Tablet PC after a password
failure, you must press the Suspend/Resume button,
then enter a correct password.
Setting Supervisor Password
You must have set a supervisor password before setting
any user passwords. The supervisor password can bypass
the user password.
1. Go to the Start menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
Uninstalling the Security Panel
Application Software
Remember the user password you specified
on the Security Panel Application. If you
forget the password you will not be able to
use your computer. The supervisor pass-
word can override the user password.
Remove passwords when User wants no password
protection whatsoever and doesn’t want to give anybody
the utility to set a password on their computer. In this
case, if passwords (supervisor, user, or both) are set, the
passwords must first be cleared BEFORE removing the
application. To clear passwords, follow same procedure
in SETTING PASSWORD CODES except this time,
select REMOVE, enter current password then click Next.
When asked to confirm select Yes.
PRECAUTIONS
Opening and Closing the Cover
By default, closing the cover automatically places your
system into Standby mode.
Windows XP systems:
Removing Security Panel Application
with Passwords Still Active
Using this feature will not allow any changes to the pass-
You can change the action the system takes when the
cover is closed by opening the Power Options Properties
icon in the Control Panel, and selecting the Advanced
tab. Make a choice from the drop down menu for “When
I close the lid of my portable computer:” and click the
[OK] button.) Opening the cover does not automatically
place the Tablet PC into normal operation. Instead, you
must enter the proper security password after pushing
the Suspend/Resume button.
word.
Removing the applications does not remove
the password. It simply removes the ability
to change/add/remove passwords. To
change your password you must reinstall the
application.
Windows Vista systems:
User:
To change the default for Windows Vista systems when
the cover is closed:
1. Go to Start -> Control Panel.
2. Open Add or Remove Programs Properties in the
1. Open the system Control Panel.
Control Panel.
2. If the display is in Category view, click "Change
battery settings" under the "Mobile PC" category. If
it is in Classic view, click "Power Options".
3. Select the Security Panel Application in the list, and
click Change/Remove.
4. When Confirm File Deletion box appears, click Yes.
3. Click "Choose what closing the lid does" in the left
pane.
Supervisor:
1. Go to Start -> Control Panel.
4. Select the desired action for "When I close the lid".
2. Open Add or Remove Programs Properties in the
Low Battery Operations
Control Panel.
If your Tablet PC has a low battery, pushing the suspend/
resume button only turns on the Security Indicator.
Your Tablet PC does not unlock, the Security Indicator
turns off after one minute. To resume normal operation,
first attach a power supply to the Tablet PC. Then you
may unlock the Tablet PC.
3. Select the Security Panel Application for Supervisor
in the list, and click Change/Remove.
4. When Confirm File Deletion box appears, click Yes.
Reinstalling the Security Panel Application
To reinstall supervisor or user security application, you
will need your Drivers and Applications CD. The Utili-
ties\Security Panel Application folder contains two
separate folders: Supervisor and User. The setup files for
supervisor and user security applications are contained
in those folders.
UNINSTALLING THE SECURITY
PANEL APPLICATION
You have two options when uninstalling the security
panel application:
■
Remove passwords and uninstall the security panel
application software. This will disable all security
features.
Uninstall the security panel application with password
still active. This will not allow any changes to the pass-
word.
1. Go to the Utilities\Security Panel Application\
Supervisor folder on the CD and double-click the
setup.exe file. The Installing Security Panel Applica-
tion window will appear. Follow the instructions on
the screen.
■
2. Go to the Utilities\Security Panel Application\User
folder on the CD and double-click the setup.exe file.
The Installing Security Panel Application window
will appear. Follow the instructions on the screen.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Supervisor and user passwords can be set via Windows
software using the FJSECS.exe and FJSECU.exe files,
respectively. FJSECU.exe for the user password cannot
run without first setting a supervisor password. You
need to run FJSECS.exe first to set the supervisor pass-
word. Follow instructions under Setting Passwords on
page 25.
If you forget both passwords, please contact Fujitsu
Computer Systems Corporation Service and Support at
1-800-8FUJITSU (1-800-838-5487). Fujitsu Computer
Systems Corporation charges a service fee for unlocking
a password-restricted Tablet PC. When calling please
have a valid credit card and provide proof of ownership.
You will then be given instructions on where to ship
your Tablet PC.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Cursor
Control
Left Button
Scroll Button
Right Button
Figure 2-20. Touchpad pointing device
DOUBLE-CLICKING
Touchpad Pointing
Device
Double-clicking means pushing and releasing the left
button twice in rapid succession. This procedure does
not function with the right button. To double-click,
move the cursor to the item you wish to select, press
and release the left button twice. (Figure 2-22)
The Touchpad pointing device built into your Tablet PC
is used to control the movement of the cursor to select
items on your display panel. The Touchpad is composed
of a cursor control, left and right buttons, and a scroll
button.
The cursor control works the same way a mouse does,
and moves the cursor around the display. It only
requires light pressure with the tip of your finger. The
left and right buttons function the same as left and right
mouse buttons. The scroll button allows you to navigate
through pages quickly without using the scroll bars. The
actual functionality of the buttons may vary depending
on the application that is being used. (Figure 2-20)
Figure 2-22. Double-clicking
■
If the interval between clicks is too long,
the double-click will not be executed.
CLICKING
■
Parameters for the Touchpad can be
adjusted from the Mouse dialog box
located in the Windows Control Panel.
Clicking means pushing and releasing a button. To left-
click, move the cursor to the item you wish to select,
press the left button once, and then immediately release
it. To right-click, move the cursor to the item you wish
to select, press the right button once, and then immedi-
ately release it. (Figure 2-21)
DRAGGING
Dragging means pressing and holding the left button
while moving the cursor. To drag, move the cursor to
the item you wish to move. Press and hold the left
button while moving the item to its new location
and then release it. (Figure 2-23)
Figure 2-21. Clicking
27
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
Figure 2-23. Dragging
SCROLLING
Using the scroll button allows you to navigate through a
document quickly without having to use the scroll bars.
This is particularly useful when you are navigating
through online pages. To use the scroll button, press the
raised horizontal line at the top or bottom of the button
to scroll up or down a page. When you have reached the
desired section of the page, release the button.
(Figure 2-24)
Figure 2-24. Scrolling
TOUCHPAD CONTROL ADJUSTMENT
The Windows Control Panel allows you to customize
your Touchpad with selections made from within the
Mouse Properties dialog box. There are several aspects of
Touchpad operation, which you can adjust.
To access the Mouse Properties window, open the
Control Panel and double-click the Mouse icon. In the
window that appears, you will see a variety of different
mouse functions that you can change.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
Volume Control
Your Fujitsu Tablet PC has multiple volume controls
which interact with each other.
Any software that contains audio files will
also contain a volume control of its own. If
you install an external audio device that has
an independent volume control, the
hardware volume control and the software
volume control will interact with each other.
It should be noted that if you set your
software volume to Off, you will override
the external volume control setting.
CONTROLLING THE VOLUME
The volume can be controlled in several different ways:
■
Volume can be set from within the Volume Control on
the Taskbar.
■
Volume can be controlled with the [F8] and [F9] func-
tions keys. Pressing [F8] repeatedly while holding [Fn]
will decrease the volume of your Tablet PC. Pressing
[F9] repeatedly while holding [Fn] will increase the
volume of your Tablet PC.
■
Volume can be controlled by many volume controls
that are set within individual applications.
■
Certain external audio devices you might connect to
your system may have hardware volume controls.
■
Each source discussed above puts an upper limit on
the volume level that must then be followed by the
other sources.
We recommend that you experiment with the various
volume controls to discover the optimal sound level.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
to the right mouse button (when used in combination
with the tip switch). The rear toggle of the barrel button
switch and the eraser switch at the end of the barrel act
as electronic ink “erasers”.
Pen and Active Digitizer
USING THE PEN
You can use the LifeBook T4200 Series Tablet PC pen to
generate and create electronic “ink”, to select items, and
to navigate through programs on the Tablet PC.
Programs that support handwriting recognition also
allow you to write characters directly on the screen with
the pen. You can also use the pen as a drawing tool.
The rear toggle, eraser, and tip click pressures can be
changed by clicking [Start] -> Control Panel, and
double-clicking the Fujitsu Pen Settings icon. Note that
the rear toggle switch and the eraser switch are both
affected by the same settings; they cannot be changed
individually.
To change the rear toggle and eraser button function,
select the drop-down list to select a new function, then
click [Apply]. If you don’t want the rear toggle and
button switch to have any function, select Ignore from
the list.
You are advised to use a screen protector
on your system display to minimize the
chance of its being scratched. Screen
protectors are available from the Fujitsu
Website at us.fujitsu.com/computers.
Adjusting the click pressure determines how much pres-
sure must be put on the pen tip in order for the screen to
react. The softer it is set, less pressure is required; the
harder it is set, more pressure is required. To change the
click pressure, use the slider bar to make the click pres-
sure harder or softer, then click [Apply].
Eraser Button
Barrel Switch
Tip Switch
Use only the pen provided with your
Tablet PC. Do not use substitutes that
were not designed for the LifeBook T4200
Series Tablet PC.
Figure 2-25. LifeBook T4200 Series Pen
Here are some hints that may help you use the pen more
effectively:
The LifeBook T4200 Series Tablet PC pen
is a high-quality electronic instrument that
can be damaged if used improperly. Treat
the pen as you would any precision device.
Observe the following guidelines:
•
To activate the tip switch, tap or hold the pen tip
against the screen.
•
To activate the barrel button switch, press and hold
the end of the button you wish to use (front toggle is
the right mouse button switch; the rear toggle and
eraser button both act as electronic “erasers”).
• Do not tap the pen on surfaces other
than the Tablet PC screen.
• Do not try to turn the thumb grip on
the pen; it is designed for inserting and
removing the pen from the pen holder.
•
•
To move the cursor, hold the pen tip within 1/8 inch
(3 - 5 mm) from the screen and move the pen.
To start a program, double-tap the pen tip (tap the
pen tip twice rapidly) on the program icon as you
would double-click a mouse.
• Never store the pen with the tip bearing
the weight of the pen (e.g., sitting tip
down in a pencil cup). Storing the pen
tip down could distort the internal
mechanism over a period of time
(especially in higher temperatures),
causing the tip to act as if it is always
depressed. The pen should be stored in
the pen holder when not in use.
•
•
To select an object, tap the pen tip on the object
once.
To double-click an object, quickly tap the object
twice.
INSTALLING A PEN TETHER
The screen reacts when the pen tip is approximately 1/8
inch (3-5 mm) from the screen. The pen has four
switches: a tip switch, a barrel button toggle switch with
switches at both ends, and an "eraser" switch, located on
the end of the barrel. By default, the tip switch corre-
sponds to the left mouse button, and the front toggle
(closest to the pen tip) barrel button switch corresponds
To prevent dropping or losing your pen, you should
attach it to your system using the pen tether that is
included with the system.
To attach the pen tether to your Tablet PC, perform the
following steps:
30
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g t o K n o w Yo u r Ta b l e t P C
1. Attach the end of the pen tether with the smaller
loop to your pen. To do so, push the end of the
tether through the hole in the pen, then thread the
opposite end of the tether through the loop. (See
Figure 2-26.)
Gap
Pen tether
attachment
point
Figure 2-27. Tip Removal Tool
To replace the tip, retrieve one of the new tips that
accompanied your pen. Insert the flat end of the tip into
the barrel and push it in firmly until it is seated.
Larger loop
Smaller loop
If you need more tips, they can be ordered from the
Fujitsu Website at: us.fujitsu.com/computers.
Figure 2-26. Installing a Pen Tether
USING THE ACTIVE DIGITIZER
2. Attach the end of the pen tether with the larger loop
to the attachment point on your tablet. To do so,
insert the end of the pen tether through the attach-
ment point, then feed the pen through the large
loop in the tether.
The integrated active digitizer allows you to use the
included pen as a pointing device. You can use the pen
to click, double-click, drag items and icons, or to draw
like a pen or pencil in applications that support this
behavior, such as drawing or painting programs. See the
documentation that came with your application for
details. (Figure 2-28)
CALIBRATING THE PEN
In order to ensure accurate tracking between the pen
and cursor, you must run the Touch Screen Calibration
Utility before you use the active digitizer for the first
time, or after you change the display resolution.
To run the calibration utility:
1. Go to Start -> Control Panel and double-click on
the Tablet and Pen Settings icon.
2. Click Calibrate.
3. Adjust the display of your Tablet PC to a comfort-
able angle.
4. Using the pen, firmly touch the screen directly on
the (+) symbol; the (+) symbol will move to the
next location.
Figure 2-28. Using the pen with the screen
5. Repeat step 4 in the four corners, then click OK.
To avoid potential scratching and damage,
never use anything but the included pen
with the display.
REPLACING THE PEN TIP
With use, the pen tip may become worn or may pick up
foreign particles that can scratch the screen. A damaged
or worn tip may not move freely, causing unpredictable
results when using the pen. If your pen exhibits these
problems, you should replace the pen tip. To do so, use
the pen tip removal tool included with your pen.
To purchase additional or replacement
pens, visit the Fujitsu accessories Website
at: http://us.fujitsu.com/computers.
Clicking
To remove the tip, position the tip in the gap between
the two ends of the tool (Figure 2-27). Pinch the tool
together so the tip is firmly clasped, then pull it from the
barrel. If the tip is worn or damaged, discard it.
To left-click, touch the object you wish to select and then
lift the pen tip immediately. (Figure 2-29)
To right-click, press the front button on the barrel
switch or touch the pen to the screen for a couple of
seconds until the right mouse icon appears at the tip.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T w o
Figure 2-29. Clicking the screen
Double-Clicking
To double-click, touch the item twice, and then immedi-
ately remove the pen tip. (Figure 2-30)
Figure 2-30. Double-clicking the screen
■
If the interval between taps is too long,
the double-click will not be executed.
■
Parameters for the screen can be
adjusted from the Mouse Properties dia-
log box located in the Windows Control
Panel.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Using Your Tablet PC
33
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T h r e e
34
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
DC Power Plug
DC Output Cable
AC Adapter
AC Cable
Figure 3-1. Connecting the AC Adapter
Connecting the Optional Auto/Airline Adapter
1. Plug the DC output cable into the DC power jack
on your Tablet PC.
Power Sources
Your LifeBook T4200 Series Tablet PC has three possible
power sources: a primary Lithium ion battery, an AC
adapter or an optional Auto/Airline adapter.
2. Plug the Auto/Airline adapter into the cigarette
lighter of an automobile with the ignition key in
the On or Accessories position.
CONNECTING THE POWER ADAPTERS
The AC adapter or optional Auto/Airline adapter
provides power for operating your Tablet PC and
charging the battery.
OR
3. Plug the Auto/Airline adapter into the DC power
jack on an airplane seat.
Switching from AC Adapter Power or the
Auto/Airline Adapter to Battery Power
1. Be sure that you have a charged battery installed.
Connecting the AC Adapter
1. Plug the DC output cable into the DC power jack
of your Tablet PC.
2. Remove the AC adapter or the Auto/Airline adapter.
2. Plug the AC adapter into an AC electrical outlet.
(Figure 3-1)
The Lithium ion battery is partially charged
upon purchase. Initially, you should
connect either the AC adapter or the
Auto/Airline adapter to use your Tablet PC
so that it can fully charge.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T h r e e
Power Management
Your LifeBook T4200 Series Tablet PC has many options
and features for conserving battery power. Some of these
features are automatic and need no user intervention,
such as those for the internal modem. However, others
depend on the parameters you set to best suit your oper-
ating conditions, such as those for the display bright-
ness. Internal power management for your Tablet PC
may be controlled from settings made in your operating
system, pre-bundled power management application, or
from settings made in BIOS setup utility.
Besides the options available for conserving battery
power, there are also some things that you can do to
prevent your Tablet PC battery from running down as
quickly. For example, you can create an appropriate
power saving profile, put your Tablet PC into Standby
mode when it is not performing an operation, and you
can limit the use of high power devices. As with all
mobile, battery powered computers, there is a trade-off
between performance and power savings.
Power Mode
System Activity
Events causing system to enter mode state
■
Fully On Mode
System is running. CPU, system bus, and
all other interfaces operate at full speed.
From Standby mode: System operation resumed
(Suspend/Resume button pressed, resume on
modem ring, resume on time).
■
From Hibernation mode: Suspend/Resume button
pressed.
■
From Off mode: Suspend/Resume button pressed.
■
Standby Mode
(Suspend-to-RAM)
Resume system logic remains powered
and RAM remains powered to maintain
active data. All other devices are turned
off.
Standby timeout occurs.
Suspend request issued by software or by pressing
the Suspend/Resume button.
Low battery.
■
■
■
Hibernation Mode
(Suspend-to-Disk)
Windows saves desktop state (including
open files and documents) to hard disk.
CPU stops. All other devices are turned
off.
Hibernate timeout occurs.
Clicking Start -> Shut Down -> Hibernate
(It may be necessary to Enable Hibernate Support
from Windows Power Options.)
Low battery condition
■
■
■
Power Off
System is fully powered off except for
logic components required for Suspend/
Resume button and real-time clock
operation.
System shutdown.
Low battery condition
■
Table 3-1. System Power States
SUSPEND/RESUME BUTTON
STANDBY MODE
When your Tablet PC is active, the Suspend/Resume
button can be used to manually put your Tablet PC into
Standby mode. Push the Suspend/Resume button when
your Tablet PC is active, but not actively accessing
anything, and immediately release the button. You will
hear two short beeps and your system will enter Standby
mode. (See figure 2-6 on page 13 for location).
Standby mode in Windows saves the contents of your
Tablet PC’s system memory during periods of inactivity
by maintaining power to critical parts. This mode will
turn off the CPU, the display, the hard drive, and all of
the other internal components except those necessary to
maintain system memory and allow for restarting. Your
Tablet PC can be put in Standby mode by:
■
If your Tablet PC is suspended, pushing the Suspend/
Resume button will return your Tablet PC to active
operation. You can tell whether or not your system is in
Standby mode by looking at the Power indicator. See
“Power Indicator” on page 16. If the indicator is visible
and not flashing, your Tablet PC is fully operational. If
the indicator is both visible and flashing, your Tablet PC
is in Standby mode. If the indicator is not visible at all,
the power is off or your Tablet PC is in Hibernate mode
(See Hibernate Mode)
Pressing the Suspend/Resume button when your
system is turned on.
Selecting Standby from the Windows Shut Down
menu.
Timing out from lack of activity.
Allowing the battery to reach the Dead Battery
Warning condition.
Closing the system cover.
■
■
■
■
Your Tablet PC’s system memory typically stores the
file(s) on which you are working, open application(s)
information, and any other data required to support the
operation(s) in progress. When you resume operation
36
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
from Standby mode, your Tablet PC will return to the
point where it left off. To resume operation, you must
use the Suspend/Resume button to resume operation,
and there must be an adequate power source available,
2. Select the desired action from the list.
Windows XP
1. Click the Start button, and then click Shut Down.
or your Tablet PC will not resume.
2. Select the Restart option from within the Windows
Shut Down dialog box.
3. Click OK to restart your notebook. Your notebook
If you are running your Tablet PC on
battery power, be aware that the battery
continues to discharge while your Tablet
PC is in Standby mode, though not as fast
as when fully operational.
will shut down and then reboot.
Turning off your LifeBook notebook with-
out exiting Windows or turning on your
notebook within 10 seconds of the note-
book being shut off may cause an error
when you start the next time.
HIBERNATION (SAVE-TO-DISK) FEATURE
The Hibernation feature saves the contents of your
notebook’s system memory to the hard drive as a part of
the Suspend/Resume mode. You can enable or disable
this feature.
POWER OFF
Before turning off the power, check that the hard drive/
optical drive access indicator is off. (See figure 2-3 on
page 6) If you turn off the power while accessing a disk
there is a risk of data loss. To ensure that your notebook
shuts down without error, use the Windows shut down
Enable or Disable the Hibernation Feature
Windows Vista:
The default settings are not enabled. To enable or disable
the Hibernation feature follow these steps:
procedure.
1. From the Start menu, select Control Panel.
Be sure to close all files, exit all applica-
tions, and shut down your operating sys-
tem prior to turning off the power. If files
are open when you turn the power off,
you will lose any changes that have not
been saved, and may cause disk errors.
2. Select “Choose what the power button does” or
“Choose what closing the lid does”, then make your
selections (Do Nothing, Sleep, Hibernate, or Shut
Down).
Windows XP:
The default settings are not enabled. To enable or disable
the Hibernation feature follow these steps:
Using the correct procedure to shut down from Windows
allows your notebook to complete its operations and turn
off power in the proper sequence to avoid errors. The
proper sequence is:
1. From the Start menu, select Settings, and then select
Control Panel.
1. Click the Start button, and then click Shut Down.
2. From the Control Panel select Power Options.
2. Select the Shut Down option from within the
3. Select the Hibernate tab. Select the box to enable or
Windows Shut Down dialog box.
disable this feature.
3. Click OK to shut down your notebook.
WINDOWS POWER MANAGEMENT
If you are going to store your notebook for a month or
more see Care and Maintenance Section.
The Power Options icon located in the Windows
Control Panel allows you to configure some of the power
management settings. For example, you can use the
Power Options to set the timeout values for turning off
the display and hard disks whether you are running the
notebook on battery power or one of the adapters.
RESTARTING THE SYSTEM
If your system is on and you need to restart it, be sure
that you use the following procedure.
Windows Vista
1. Click the Start button, and then move the mouse
over the right arrow.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
loaded. During booting, your Tablet PC is performing a
standard boot sequence including a Power On Self Test
(POST). When the boot sequence is completed without
a failure and without a request for the BIOS Setup
Utility, the system displays the operating system’s
opening screen.
Starting Your Tablet PC
POWER ON
The Suspend/Resume button is used to turn on your
LifeBook T4200 Series Tablet PC from its off state. Once
you have connected your AC adapter or charged the
internal Lithium ion battery, you can power on your
Tablet PC. .
The boot sequence is executed when:
■
You turn on the power to your Tablet PC.
You restart your Tablet PC from the Windows
■
Shut Down dialog box.
The software initiates a system restart. Example:
When you install a new application.
When you turn on your Tablet PC, be sure
you have a power source. This means that
a battery is installed and charged, or that
the AC or Auto/Airline adapter is
■
connected and has power.
HARD DISK DRIVE PASSWORDS
To provide additional security for your data, you can
assign passwords to the hard disk drive(s). This feature is
managed in the system BIOS Setup Utility. See BIOS
Setup Utility below for information about accessing the
utility.
Press the Suspend/Resume button to start your
system.(See Figure 2-4 on page 10 for location). When
you are done working you can either leave your Tablet
PC in Standby mode, See “Standby Mode” on page 36,
or you can turn it off. See “Power Off” on page 37.
Remember your passwords. If you set and
forget your User and Master hard disk
passwords, Fujitsu Computer Systems will
not be able to reset it. You may lose data
and have to replace your system board or
hard disk drive.
When the system display is closed, the
Suspend/Resume button is disabled. This
feature prevents the system from being
accidentally powered up when not in use.
When you Power On your Tablet PC, it will perform a
Power On Self Test (POST) to check the internal parts
and configuration for correct functionality. If a fault is
found, your Tablet PC will emit an audio warning and/
or an error message will be displayed. See “Power On
Self Test Messages” on page 65. Depending on the nature
of the problem, you may be able to continue by starting
the operating system or by entering the BIOS setup
utility and revising the settings.
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your Tablet PC. Your BIOS
is set at the factory for normal operating conditions,
therefore there is no need to set or change the BIOS’
environment to operate your Tablet PC.
The BIOS Setup Utility configures:
■
Device control feature parameters, such as changing
After satisfactory completion of the Power On Self Test
(POST), your Tablet PC will load your operating system.
I/O addresses and boot devices.
System Data Security feature parameters, such
as passwords.
■
Never turn off your Tablet PC during the
Power On Self Test (POST) or it will cause
an error message to be displayed when
you turn your Tablet PC on the next time.
See “Power On Self Test Messages” on
page 65
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following (or use
the TrustedCore Menu, as detailed in the next section):
1. Turn on or restart your LifeBook notebook.
2. To enter the BIOS Setup Utility, press the [F2] key
once the Fujitsu logo appears on the screen. This will
open the main menu of the BIOS Setup Utility with
the current settings displayed, or,
BOOT SEQUENCE
The procedure for starting-up your Tablet PC is termed
the Bootup sequence and involves your Tablet PC’s
BIOS. When your Tablet PC is first turned on, the main
system memory is empty, and it needs to find instruc-
tions to start up your Tablet PC. This information is in
the BIOS program. Each time you power up or restart
your Tablet PC, it goes through a boot sequence which
displays a Fujitsu logo until your operating system is
3. Press the [RIGHT ARROW] or [LEFT ARROW] key
to scroll through the other setup menus to review or
alter the current settings.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n T h r e e
Using the TrustedCore Menu
STARTING WINDOWS VISTA THE FIRST TIME
When the Fujitsu logo appears on the screen. press the
[Enter] key or click on the left mouse or touchpad
button; the TrustedCore Menu will appear.
The first time you initialize your Windows
Vista system, the screen will be blank for
approximately two minutes. This is
normal. After initialization, a “Set Up
Windows” dialog box will appear.
The TrustedCore Menu provides shortcuts to the
following menus and information screens:
■
Important: During the setup procedure, do
not disconnect the power supply, press any
buttons, or use any peripheral devices such
as a mouse, keyboard, or remote control.
BIOS Setup
Diagnostic Screen
Boot Menu
Patent Information
System Information
Continue Booting
■
■
■
■
■
In order to ensure that you receive the most benefits
from the Windows Vista operating system, it should be
registered the first time you use it.
Clicking on any of the fields will invoke the screen,
information, or action described.
1. First of all, you will need to read and accept the End
User License Agreements (EULAs).
The Boot Menu can also be invoked by pressing the
[F12] key when the Fujitsu logo appears on the screen.
■
If you reject the terms of the license
BIOS Guide
agreement you will be asked to review
the license agreement for information
on returning Windows or to shut down
your LifeBook notebook.
A guide to your Tablet PC’s BIOS is available online.
Please visit our service and support Website at http://
www.computers.us.fujitsu.com/support. Once there,
select Support, then select Tablet PCs under User’s
Guides. Select LifeBook Tablet PC BIOS Guides from
the pull-down menu for your Tablet PC series. If you are
unsure of your Tablet PC’s BIOS number, refer to your
packing slip.
■
You cannot use your notebook until you
have accepted the License Agreement. If
you stop the process your notebook will
return to the beginning of the Windows
Welcome Process, even if you shut your
notebook down and start it up again.
If your data security settings require it, you
may be asked for a password before the
BIOS main menu will appear.
2. You will be prompted to enter your User Name and
Password and you will be given a chance to select an
icon for your account.
3. The next screen asks for a Computer Name and
allows you to choose a desktop background.
BOOTING THE SYSTEM
4. You will next see a "Help protect Windows automat-
ically" screen in which the default choice is "Use
recommended settings”. The other two choices are
"Install important updates only" and "Ask me later".
Select from the three choices.
We strongly recommend that you not attach any
external devices and do not put a DVD/CD in your drive
until you have gone through the initial power on
sequence.
When you turn on your LifeBook notebook for the first
time, it will display a Fujitsu logo on the screen. If you
do nothing the system will load the operating system,
and then the Windows Welcome will begin.
5. On the next screen set your time and date settings.
6. You will next see the "Select your computer's current
location" screen. Make your selection from Home,
Work (Default), and Public location.
Depending upon your operating system (Windows Vista
or XP edition), there is a different procedure for stating
your system for the first time, as outlined below.
7. The "Thank you" screen follows and an offer for free
Norton is extended. Following are several screens
while Windows checks the system performance.
8. Windows will then boot up for the first time.
Registering Windows Vista with Microsoft
1. After Windows has booted up for the first time, the
Control Panel Welcome Center will appear. If the
Register Windows Online icon is not seen in the
window, click on “Show all 14 items”.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t t i n g S t a r t e d
2. Click on Register Windows Online and follow the
instructions that appear to register your copy of
Windows.
REGISTERING YOUR LIFEBOOK NOTEBOOK
How do I register my LifeBook notebook?
You can register your LifeBook by going to our website:
STARTING WINDOWS XP THE FIRST TIME
Registering Windows XP with Microsoft
us.fujitsu.com/computers
You will need to be set up with an Internet Service
Provider (ISP) to register online.
In order to ensure that you receive the most benefits
from the Windows operating system, it should be
registered the first time you use it.
ClickMe! INSTALLING CLICK ME!
After you receive the Windows Welcome screen, you will
be prompted to enter registration information in the
following order.
Before installing the ClickMe! utility, be
sure the wireless LAN switch is turned on.
First of all, you will need to read and accept the End
User License Agreements (EULAs). After accepting the
EULAs, you will be asked if you want to enable the Auto-
matic Updates feature. Acceptance of this feature is
recommended because it allows your system to be
updated automatically whenever an important change
becomes available for your notebook.
Windows Vista Systems
The first time you boot up your system, you will see a
“Primary Settings for the PC” window. This window
explains the installations which will be performed by the
Click Me! utility. If you click [Execute], Click Me! will
begin installing. If after clicking the button you receive a
“User Account Control” window, you will be asked for
your permission to continue. Click [Yes] to continue. If
you cancel the operation, the Click Me! icon will appear
on your desktop for later installation.
■
If you reject the terms of the license
agreement you will be asked to review
the license agreement for information
on returning Windows or to shut down
your LifeBook notebook.
■
You cannot use your LifeBook notebook
until you have accepted the License
Agreement. If you stop the process your
notebook will return to the beginning of
the Windows Welcome Process, even if
you shut your notebook down and start
it up again.
Windows XP Systems
The first time you boot up your system, you will see an
icon called Click Me! in the Start menu. We highly
recommend that you install the ClickMe! utility the
first time you boot up. When you click the Click Me!
icon, your system will automatically build the icon tray
in the bottom right of the screen. These icons provide
links to utilities that you will frequently access., such as
wireless LAN software provided by the wireless LAN
manufacturer.
Several additional windows will appear, prompting you
to enter a name and description for your computer, an
Administrator password, and a domain name. Read the
instructions on the screens carefully and fill in the infor-
mation as directed.
There may be additional third-party
applications that are not installed by the
ClickMe! utility. For more information,
refer to your Getting Started Guide.
You will then be automatically connected to the
Internet, if you have an appropriate connection avail-
able. If an automatic connection is not possible, you will
be asked about how you dial out from where you will be
using your LifeBook notebook. If you are not connected
to a phone line and plan to register at a later time, you
may click the Skip button.
FUJITSU DRIVER UPDATE UTILITY
Your system has a convenient tool called the Fujitsu
Driver Update (FDU) utility. With FDU, you can choose
to automatically or manually go to the Fujitsu site to
check for new updates for your system. For more infor-
mation about the FDU utility, refer to “Automatically
Downloading Driver Updates” on page 83.
Once you are connected to the Internet, you will be
asked if you wish to continue with the registration. If
you select Yes you will then enter your name and
address, and email address if desired. Click Next to
complete registration.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
4
User-Installable
Features
41
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F o u r
42
Download from Www.Somanuals.com. All Manuals Search And Download.
U s e r - I n s t a l l a b l e F e a t u r e s
The Lithium ion battery is recharged internally using the
AC adapter or Auto/Airline adapter. To recharge the
battery make sure the battery that needs to be charged is
installed in your Tablet PC and connect the AC or Auto/
Airline adapter.
Lithium ion Battery
Your LifeBook T4200 Series Tablet PC has a Lithium ion
battery that provides power for operating your Tablet
PC when no external power source is available. The
battery is durable and long lasting, but should not be
exposed to extreme temperatures, high voltages, chemi-
cals or other hazards.
Make sure that the Battery Charging
indicator and the percentage charge is
shown inside the Battery Level icon on the
Status Indicator Panel.
The Lithium ion battery operating time may become
shorter if it is used under the following conditions:
■
When used at temperatures lower than 41° F (5° C) or
There is no memory effect on the Lithium ion battery,
therefore you do not need to discharge the battery
completely before recharging. The charge times will be
longer if your Tablet PC is in use while the battery is
charging. If you want to charge the battery more quickly,
put your Tablet PC into Standby mode, or turn it off
while the adapter is charging the battery. See “Power
Management” on page 36.
higher than 95° F (35° C). Extreme temperatures not
only reduce charging efficiency, but can also cause
battery deterioration. The Charging icon on the Status
Indicator panel will flash when you try to charge a
battery that is outside its operating temperature range.
See “Battery Charging/ Level Indicators” on page 16.
■
When using a high current device such as a modem,
CD-ROM drive, or hard drive, using the AC adapter
will conserve your battery life.
Using heavy current devices such as a
modem or frequent CD-ROM and
PCMCIA powered external device accesses
may prevent charging completely.
■
Do not leave a faulty battery in your
Tablet PC. It may damage your AC
adapter, optional Auto/Airline adapter,
another battery or your Tablet PC itself.
It may also prevent operation of your
Tablet PC by draining all available cur-
rent into the bad battery.
Low Battery State
When the battery is running low, your Tablet PC will
beep every 15 seconds and the Battery Level indicator
will flash. If you do not respond to the low battery
alarm, the batteries will continue to discharge until they
are too low to operate. When this happens there will be a
multiple beep alarm and the Battery Level indicator will
show a dead battery. Your Tablet PC will then go into
Standby mode to try and protect your data for as long as
possible. There is no guarantee that your data will not be
lost once the Tablet PC reaches this point.
■
Under federal, state, or local law it may
be illegal to dispose of batteries by
putting them in the trash. Please take
care of our environment and dispose of
batteries properly. Check with your local
government authority for details
regarding recycling or disposing of old
batteries. If you cannot find this infor-
mation elsewhere, contact your support
representative at 1-800-8Fujitsu.
■
You may not be able to hear the alarm if
the volume control is set too low or is
turned off by the hardware or software.
However, you will be able to see the
Battery Level indicator flash. Once the
low battery alarm occurs you must save
all your data and put your Tablet PC into
Standby mode until you can provide a
new power source. You should provide a
charged battery or AC or Auto/Airline
Adapter as soon as possible.
Actual battery life will vary based on
screen brightness, applications, features,
power management settings, battery
condition and other customer preferences.
CD-ROM drive or hard drive usage may
also have a significant impact on battery
life. The battery charging capacity is
reduced as the battery ages. If your
battery is running low quickly, you should
replace it with a new one.
■
When you are in Standby mode there
must always be at least one power
source active. If you remove all power
sources while your Tablet PC is in
RECHARGING THE BATTERY
Standby mode, any data that has not
been saved to the hard drive will be lost.
If you want to know the condition of the Lithium ion
battery, check the Battery Level indicator located on the
Status Indicator panel. The indicator changes as the
battery level changes.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F o u r
Dead Battery Suspend mode shows on the Status indi-
cator just like the normal Standby mode. Once your
Tablet PC goes into Dead Battery Suspend mode you
will be unable to resume operation until you provide
a source of power either from an adapter, or a charged
battery. Once you have provided power, you will need to
press the Suspend/Resume button to resume operation.
In the Dead Battery Suspend mode, your data can be
maintained for some time, but if a power source is not
provided promptly, the Power indicator will stop
flashing and go out, meaning that you have lost the data
that was not stored. Once you provide power, you can
continue to use your Tablet PC while an adapter is
charging the battery.
Battery Release Latches
Shorted Batteries
The Status Indicator panel uses a symbol inside the
battery outline of the Battery Level indicator to display
the operating level available in that battery.
(See figure on page 16) If this display shows a Shorted
Battery, it means that the battery is damaged and must
be replaced so it does not damage any other parts of your
Tablet PC.
Battery Compartment
Figure 4-1. Removing the Battery
Warm-swapping Batteries
To warm-swap batteries in your battery compartment
REPLACING THE BATTERY
follow these easy steps: (Figure 4-1)
Your LifeBook T4200 Series Tablet PC comes with one
battery pack; you might want to consider purchasing a
spare. By keeping a spare battery fully charged, you can
immediately swap with one that is not charged.
You have only a few minutes to perform a
warm-swapping before the internal
bridge battery runs out of power. Have
the charged battery nearby when
There are two ways to swap batteries: cold-swapping and
warm-swapping. Cold-swapping means swapping
batteries when the system has been powered down;
warm-swapping is performed when the system is in
Standby mode.
performing a warm battery swap.
1. Close any open files and put your Tablet PC into
Standby mode.
2. Press the battery release latches to open the
compartment.
Cold-swapping batteries
3. Remove the battery from the compartment.
4. Slide the new battery into the compartment.
To cold-swap batteries in your battery compartment,
follow these easy steps: (Figure 4-1)
5. Close the compartment and the battery release
latches will click into place.
1. Have a charged battery ready to install.
2. Shut down your tablet and disconnect the AC
adapter.
6. Press the Suspend/Resume button to return your
Tablet PC to normal operation.
3. Press the battery release latches to open the
compartment.
If the Lithium ion battery connector is not
fully seated, you may not be able to use
your Tablet PC or charge your battery.
4. Remove the battery from the compartment.
5. Slide the new battery into the compartment.
6. Close the compartment and the battery release
latches will click into place.
7. Plug in the AC adapter and turn the power on.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
U s e r - I n s t a l l a b l e F e a t u r e s
Memory Upgrade
Module
Your Fujitsu LifeBook T4200 Series Tablet PC comes with
a minimum of 512 MB of high speed Double Data Rate 2
Synchronous Dynamic RAM (DDR2 SDRAM), 667 MHz
factory installed. The maximum memory capacity is 4 GB
(2 GB x 2), but 3.25 GB is the maximum amount that is
usable by the operating system. To increase your system’s
memory capacity, you may install an additional memory
upgrade module. The memory upgrade must be a dual-
in-line (DIMM) SDRAM module. To ensure 100%
compatibility, purchase the SDRAM module only from
the Fujitsu web store at us.fujitsu.com/computers.
Figure 4-2. Opening the Memory Upgrade Compartment
5. Remove the memory upgrade module from the
static guarded sleeve.
■
Do not remove any screws from the
6. Align the memory upgrade module with the
component side up. Align the connector edge of the
memory upgrade module with the connector slot in
the compartment. (Figure 4-3)
memory upgrade module compartment
except the ones specifically shown in the
directions for installing and removing the
memory upgrade module.
7. Insert the memory upgrade module at a 45° angle.
Press the connector edge of the module firmly down
and into the connector until it lodges under the
retaining clip. You will hear a click when it is prop-
erly in place.
■
The memory upgrade module can be
severely damaged by electrostatic dis-
charge (ESD). To minimize risk to the
module, observe the following precau-
tions:
■
Before handling a memory module,
touch a grounded metal object to
discharge static electricity built up in
your body.
■
When installing or removing a
memory module, hold it by the edge
so as not to touch any contacts or
chips. Be careful not to touch any
internal computer terminals or
components; the oil from your
fingers could cause a short to the
components.
■
Be sure to power down your system
before adding or removing memory
modules. Even if the system is in
hibernate or standby states, data
could be lost or the memory could be
damaged if power is still available to
the system.
Figure 4-3. Installing a Second Memory Module
8. Replace the cover. (Figure 4-4)
9. Replace the screws.
INSTALLING MEMORY UPGRADE MODULES
1. Turn off power to your LifeBook Tablet PC and
remove any power adapter (AC or auto/airline).
2. Make sure that all the connector covers are closed.
3. Turn the Tablet PC bottom side up, and remove the
screws of the memory upgrade module compart-
ment. (Figure 4-2)
4. Remove the cover.
Figure 4-4. Replacing the Memory Compartment Cover
45
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F o u r
CHECKING THE MEMORY CAPACITY
Once you have changed the system memory capacity by
either adding or removing a memory upgrade module,
be sure to check that your tablet has recognized the
change.
The memory upgrade module is not
something you routinely remove from
your tablet. Once it is installed, you should
leave it in place unless you want to change
system memory capacity.
Your Tablet PC uses Dynamic Video
Memory Technology (DVMT), which
allows the video driver to dynamically
determine the amount of memory that is
used. Your system can use the following
maximums for video functions:
REMOVING A MEMORY UPGRADE MODULE
1. Perform steps 1 through 4 of Installing a Memory
Upgrade Module.
2. Pull the clips sideways away from each side of the
memory upgrade module at the same time.
3. While holding the clips out, remove the module
from the slot by lifting it up and pulling towards the
rear of your tablet. (Figure 4-5)
Windows XP: 128 MB
Windows Vista: 64 MB (with 512 MB
system memory); 256 MB (with 1 GB
system memory); 384 MB 9 with 1.5 GB or
more system memory).
You can check the memory capacity by clicking [Start]
-> Control Panel, then double-clicking the System icon.
Select the General tab and check the amount of memory
under “Computer.”
Figure 4-5. Removing a Memory Upgrade Module
The amount of memory displayed should be approxi-
mately the total of all memory modules installed. There
may be a discrepancy of 8 MB which is allocated for
fixed video memory.
4. Store the memory upgrade module in a static
guarded sleeve.
5. Replace the cover. (Figure 4-4)
6. Replace the screws.
If the total memory displayed is incorrect,
check that your memory upgrade module
is properly installed. (If the module is
properly installed and the capacity is still
not correctly recognized, see
Troubleshooting on page 58.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
U s e r - I n s t a l l a b l e F e a t u r e s
Flexible Bay Eject Lever
Flexible Bay
Figure 4-6 Flexible Bay
Using the Optical Drive Disabling Feature
The CD/DVD tab of the Fujitsu Tablet Controls window
consists of three checkboxes:
Flexible Bay Devices
Your Fujitsu Tablet PC contains a Flexible Bay. The Flex-
ible Bay can house an optical drive, a Lithium ion
battery, or a weight saver. (Figure 4-6)
■
Lock CD/DVD drive when the unit is in tablet mode
■
Show tray icon when CD/DVD drive is locked.
Your Flexible Bay will have one of the following devices
installed.
■
Show notification messages when CD/DVD drive is
locked/unlocked
■
Modular Dual-Layer Multi-Format DVD Writer: This
Lock CD/DVD drive when the unit is in tablet mode:
This checkbox should normally be checked (see “Impor-
tant Notes” above). If you would like to access the DVD
drive while your system is in undocked tablet mode,
deselect this checkbox. A message will appear asking if
you really want to unlock the drive. Click [OK] to keep
the checkbox checked, or [Cancel] to uncheck it and
return to the utility.
allows you to access movies, software, and audio
DVD/CDs and record to DVD, CD, and DVD-RAM
discs.
■
Modular DVD/CD-RW combo drive: This allows you
to access movies, software, and audio DVD/CDs as
well as to write to CDs.
■
Modular Lithium ion battery: This is a rechargeable
battery that can be used to power your Tablet PC
when an adapter is not connected.
Show tray icon when CD/DVD drive is locked:
This checkbox should normally be checked. If you
would not like the Fujitsu Tablet Controls icon to appear
in the system tray when the drive is locked, clear this
box.
■
Weight Saver: This is used to fill the bay when no
device is needed.
FUJITSU TABLET CONTROLS -
CD/DVD DRIVE HELP
Show notification messages when CD/DVD drive is
locked/unlocked:
This checkbox should normally be checked. If you
would not like to be prompted when the drive is locked
or unlocked, clear this box.
The CD/DVD Drive tab of the Fujitsu Tablet Controls
utility allows you to enable or disable your DVD drive
when the Tablet PC is used in “undocked” (i.e., not
connected to a port replicator) tablet mode.
Buttons
The DVD drive in your Tablet PC is
■
Click the [OK] button to accept the changes and close
the window.
designed to work optimally when the
system is lying flat on a stable surface.
Using the drive while the system is not on
a flat surface could result in damage to the
drive and/or the media. SUCH DAMAGE
IS NOT COVERED UNDER YOUR
WARRANTY. You are strongly advised not
to use the drive while the system is in
undocked tablet mode. This feature is in
effect only when the user is logged-in.
■
Click the [Apply] button to accept the changes and
leave the window open.
■
Click the [Cancel] button to close the window without
accepting the change.
■
Click the [Help] button to view the help file associated
with the selected tab within Fujitsu Tablet Controls.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F o u r
System Tray Icon
Flexible Bay Eject Lever
When your system is in undocked tablet mode, and the
“Lock CD/DVD drive when the unit is in tablet mode”
box is checked, a Fujitsu Tablet Controls icon will appear
at the bottom right of the display. When you select this
icon, a menu will appear containing three items:
■
Unlock CD/DVD Drive for this tablet session
■
Configure
■
About
Unlock CD/DVD Drive for this tablet session
When you click this menu item, you will be asked
whether you really want to unlock the drive. To unlock
the drive, click [Yes]. Note that enabling the drive in this
manner will not change the setting in the Fujitsu Tablet
Controls control panel applet.
Configure
When you click this menu item, the Fujitsu Tablet
Controls window appears.
About
When you click About, the help file will open.
REMOVING AND INSTALLING
MODULAR DEVICES
There are two ways to remove and install modular
Figure 4-7 Removing/Installing a device in the Flexible Bay
devices in the Flexible Bay:
Use care when aligning or seating devices
in the bay. If the fit is incorrect, you may
damage the bay or device. If the device
does not move easily in the bay, remove it
and check for dirt or foreign objects. It will
require a firm push to latch it in place.
■
Cold-swapping: swapping devices while your Tablet
PC is powered off.
■
Hot-swapping: swapping devices while your system is
active using the Safely Remove Hardware icon from
your taskbar.
You should never leave your Flexible Bay
empty when the tablet is in operation. If
left empty, dust or foreign matter may
accumulate inside the tablet.
5. Slide the device you are installing into your tablet
until it clicks into place.
6. It is now safe to turn your tablet back on.
7. You can now access and use the device.
Cold-swapping
To cold-swap modular devices in your Flexible Bay
follow these easy steps: (Figure 4-7)
Your Tablet PC will automatically detect the new device
and activate it within your system. The drive letters asso-
ciated with the device will be created and listed under
My Computer and Windows Explorer.
1. Close any open files.
2. Shut down your Tablet PC.
Hot-swapping
3. Pull out the Flexible Bay eject lever. This will push
your device out slightly, allowing you to remove it.
Hot-swapping is provided through the Safely Remove
Hardware utility. The icon for the utility appears in the
system tray. Click on the icon and follow the on-screen
instructions.
4. Slide your device out until it is clear of the bay.
This will require light force.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
U s e r - I n s t a l l a b l e F e a t u r e s
Eject Button
PC Card Slot
PC Card
Smart Card Slot
Figure 4-8. Inserting/Removing PC Cards
REMOVING PC CARDS
To remove a PC Card, follow these easy steps:
PC Cards
Your LifeBook T4200 Series Tablet PC supports Type I
and II PC Cards, which can perform a variety of func-
tions.
1. See your PC Card manual for specific instructions
on removing your card. Some PC Cards may require
your Tablet PC to be in Standby Mode or Off while
removing them.
Some available PC Cards include:
■
Fax/data modem cards.
Local area network (LAN) cards.
IDE solid-state disk cards.
SCSI cards.
If the dialog box states that the device
can’t be removed, you must save all open
files, close any open applications and shut
down your Tablet PC.
■
■
■
■
Other PC Cards that conform to PCMCIA 2.1 or
CardBus standards.
2. Push the Eject button until it pops out, and then
push it in to eject the card. This will allow you to
remove the card.
For further information, refer to the instructions
supplied with your PC Card.
INSERTING PC CARDS
PC Cards are inserted in the PC Card slot. To insert a
PC Card, follow these easy steps: (Figure 4-8)
If the PC Card has an external connector
and cable, do not pull the cable when
removing the card.
■
Inserting or removing a PC Card during
your Tablet PC’s shutdown or bootup
process may damage the card and/or
your Tablet PC.
SMART CARD READER
An embedded Smart Card Reader and a dedicated Smart
Card slot are provided on your Tablet PC. The Smart
Card slot is located just below the PC Card slot.
■
Do not insert a PC Card into the slot if
there is water or any other substance on
the card as you may permanently dam-
age the card, your Tablet PC, or both.
Smart Cards are the same size and shape as credit cards,
but they contain an integrated microprocessor chip. The
chip can hold a variety of information, and provides the
user with many possible options, such as allowing them
to make secure purchases, pay for phone calls, store
security information, and provide identification and
information.
1. See your PC Card manual for specific instructions
on the insertion of your card. Some PC Cards may
require your Tablet PC to be Off while inserting
them.
Using the Smart Card functionality of your system
requires third-party software. For instructions on using
the Smart Card slot, see the instructions that come with
the third-party software.
2. Make sure there is no PC Card currently in the slot.
If there is, see Removing PC Cards.
3. Insert your PC Card into the slot, with the product
label facing up.
4. Push the card into the slot firmly until it is seated in
the opening.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F o u r
Memory Stick
SD Card
Memory Stick/SD Card Slot
Figure 4-9. Inserting a Memory Stick/SD Card
INSERTING MEMORY STICK/SD CARDS
Memory Stick/
Memory Sticks and SD Cards are inserted in the
Memory Stick/SD Card slot (Figure 4-9). To insert a
Memory Stick or SD Card, follow these steps:
Secure Digital Media
Your LifeBook Tablet PC supports Memory Stick/
Memory Stick Pro and Secure Digital (SD) cards, on
which you can store and transfer data to and from a
variety of digital devices. These cards use flash memory
architecture, which means they don’t need a power
source to retain data.
■
inserting or removing a Memory Stick or
SD Card during your LifeBook Tablet
PC’s shutdown or bootup process may
damage the card and/or your LifeBook
Tablet PC.
■
Do not insert a card into a slot if there is
Memory Stick is a flash memory technology developed
by Sony Electronics. Memory Stick allows you to record,
transfer and share digital content, such as digital
pictures, movies, music, voice, and computer data and
applications.
water or any other substance on the
card as you may permanently damage
the card, your LifeBook Tablet PC, or
both.
Secure Digital (SD) Cards are very similar to Memory
Sticks, but they are shorter. Like the Memory Stick, SD
Cards allow portable storage among a variety of devices,
such as cell phones, GPS systems, digital cameras, and
PDAs. SD Cards transfer data quickly, with low battery
consumption. Like the memory stick, it uses flash
memory architecture.
1. See your Memory Stick or SD Card manual for
instructions on the insertion of your card. Some
cards may require that your Tablet PC is off while
inserting them.
2. Make sure there is no card currently in the slot. If
there is, see Removing a Memory Stick/SD Card.
3. Insert your PC Card into the slot with the product
label facing up.
4. Push the card firmly into the slot until it is seated in
the connector.
REMOVING A MEMORY STICK/SD CARD
Before removing a Memory Stick or SD Card, see your
Memory Stick or SD Card manual for instructions.
Some cards may require your LifeBook Tablet PC to be
in Suspend Mode or Off while removing them.
Figure 4-10. Memory Stick (left) and Secure Digital Card (right)
To remove a card, simply pull it straight out from the
slot.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
U s e r - I n s t a l l a b l e F e a t u r e s
DC Power Jack
Line Out Jack
USB Ports
LAN (RJ-45) Jack
External Monitor Port
External DVI Port
Figure 4-11. Port Replicator rear panel
Port Replicator
An optional Port Replicator is available from Fujitsu to
support your LifeBook T4200 Series Tablet PC. The Port
Replicator extends the functionality of your Tablet PC
by providing ports to connect USB devices, an external
monitor, external speaker, or a LAN device. The Port
Replicator connects to the bottom of your Tablet PC. See
DC Power Jack
The DC power jack allows you to plug in the AC adapter
to power your Tablet PC and charge the internal
Lithium ion battery.
USB 2.0 Ports
The four USB 2.0 ports allow you to connect USB
devices such as game pads, pointing devices, and
keyboards. USB 2.0 is downward-compatible with USB
1.1 devices, so older USB devices will work with these
ports. USB 2.0 is a much faster design, running 40 times
faster than USB 1.1.
“Device Ports” on page 53.
REAR PANEL COMPONENTS
Following is a brief description of the optional Port
Replicator’s rear panel components.
External Monitor Port
Line Out Jack
The external monitor port allows you to connect an
external monitor. Note that if a Port Replicator is
attached, you must use the external monitor port on the
Port Replicator. (Figure 4-11)
The line out jack is used for connecting an external
speaker. Note that line out does not provide power, so
the speaker must be externally powered.
External DVI Port
The external Digital Video Interface (DVI) port allows
you to connect an external digital flat-panel monitor or
projector. This provides a pure digital video signal for
digital monitors.
LAN (RJ-45) Jack
The LAN jack allows you to connect a LAN to the Port
Replicator. Note that when the system is attached to the
Port Replicator, the LAN Jack on the Port Replicator
should be used, not the one on the system.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F o u r
Port Replicator
Release Latch
Power On/
Off Button
Docking Port
Figure 4-12. Port Replicator front panel
FRONT PANEL COMPONENTS
Following is a brief description of the optional Port
Replicator’s front panel components
ATTACHING THE PORT REPLICATOR
To attach the Port Replicator, align the Port Replicator
connector on the bottom of your Tablet PC with the
connector on the Port Replicator and push together at
the two corners. (Figure 4-13)
Docking Port
The docking port connects the Port Replicator to your
Tablet PC. (Figure 4-12)
Port Replicator Release Latch
Slide the Port Replicator Release Latch sideways to
remove the Port Replicator from your Tablet PC.
(Figure 4-12)
Power On/Off Button
The Power On/Off button on the port replicator
performs the same as the system Suspend/Resume
button. The Power On/Off button allows you to suspend
Tablet PC activity without powering off, resume your
Tablet PC from standby mode, and power on your
system when it has been shut down from the Windows
operating system.
Figure 4-14. Unlatching the Port Replicator
DETACHING THE PORT REPLICATOR
To detach the Port Replicator:
1. Slide the Port Replicator release latch to release the
Port Replicator from your Tablet PC. (Figure 4-14)
2. Pull away the Port Replicator to detach it from your
Tablet PC. (Figure 4-15)
Figure 4-13. Attaching the Port Replicator
Before docking or undocking your
notebook with the port replicator, be sure
to touch a grounded metal object to
prevent electrostatic discharge from
affecting the computer components.
Figure 4-15. Removing the Port Replicator
52
Download from Www.Somanuals.com. All Manuals Search And Download.
U s e r - I n s t a l l a b l e F e a t u r e s
1. Align the connector with the jack opening.
2. Push the connector into the jack until it is seated.
3. Plug the other end of the cable into a LAN outlet.
Device Ports
Your LifeBook T4200 Series Tablet PC and the optional
Port Replicator come equipped with multiple Device
Ports to which you can connect an external device
including: disk drives, keyboards, modems, printers, etc.
DOCKING PORT
The docking port is used for the connection of your
Tablet PC to an optional port replicator. In order to
connect your Tablet PC to one of these devices follow the
instructions that came with your port replicator. (See
Figure 2-8 on page 15 for location)
MODEM (RJ-11) JACK
The modem (RJ-11) jack is used for an internal modem.
To connect the telephone cable follow these easy steps:
(See Figure 2-7 on page 14 for location)
UNIVERSAL SERIAL BUS PORTS
1. Align the connector with the jack opening.
The three Universal Serial Bus 2.0 ports (USB) allow you
to connect USB devices such as external floppy disk
drives, external DVD drives, game pads, pointing
devices, keyboards and/or speakers. USB 2.0 is down-
ward-compatible with USB 1.1 devices, so older USB
devices will work with these ports. USB 2.0 is a much
faster design, running forty times faster than USB 1.1.
2. Push the connector into the jack until it is seated.
3. Plug the other end of the telephone cable into a
telephone outlet.
The internal modem is not intended for
use with Digital PBX systems. Do not
connect the internal modem to a Digital
PBX as it may cause serious damage to the
internal modem or your entire LifeBook
T4200 Series Tablet PC. Consult your PBX
manufacturer’s documentation for details.
Some hotels have Digital PBX systems. Be
sure to find out BEFORE you connect your
modem.
In order to connect a USB device, follow these easy steps:
(See Figure 2-7 on page 14 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
INFRARED PORT
The Infrared IrDA 1.1 (4 Mbps) port allows for wireless
data transfer between your Tablet PC and other IrDA-
compatible devices, such as another computer or a
printer, without the use of a cable. (See Figure 2-7 on
page 14 for location)
■
The internal modem is designed to the
ITU V.90 standard. Its maximum speed
of 53000 bps is the highest allowed by
FCC, and its actual connection rate
depends on the line conditions. The
maximum speed is 33600 bps at upload.
It is important to keep in mind that while carrying out
this form of communication, both devices must be
placed so their infrared ports are directly facing each
other without obstruction. The devices must also be
separated by at least 6" but no more than 36" for
maximum performance.
■
The internal modem on all LifeBook
T4200 Series Tablet PC’s from Fujitsu
Computer Systems Corporation are
certified for use in the United States and
Canada.
The following conditions may interfere with infrared
communications:
INTERNAL LAN (RJ-45) JACK
The internal LAN (RJ-45) jack is used for an internal 10/
100/1000 Base-T/Tx (Gigabit) Ethernet connection. You
will need to configure your Tablet PC to work with your
particular network. (Please refer to your network
administrator for information on your network
configuration.) To connect the LAN cable follow these
easy steps: (See Figure 2-7 on page 14 for location)
■
A television, radio remote control unit, or a wireless
headphone is being used nearby.
■
Direct sunlight, fluorescent light, or incandescent
light shines directly on the port.
■
Do not move either device while com-
munication is active as it may interrupt
data transmission.
Note that the optional Port Replicator is
designed to cover the LAN jack located on
the system. This ensures that the LAN jack
on the Port Replicator is the only one used
when the Port Replicator is installed.
■
Be careful not to scratch the infrared
port lens. Scratches, dirt, or other sur-
face marks can degrade operation.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F o u r
MICROPHONE JACK
EXTERNAL VIDEO PORT
The microphone jack allows you to connect an external
mono microphone. Your microphone must be equipped
with a 1/8”(3.5 mm) mono mini-plug in order to fit into
the microphone jack of your Tablet PC. In order to
connect a microphone follow these easy steps: (See
Figure 2-4 on page 10 for location)
The external video port allows you to connect an
external monitor or LCD projector. In order to connect
an external monitor follow these easy steps: (See
Figure 2-7 on page 14 for location). There is also an
external VGA monitor on the port replicator (See
Figure 4-11 on page 51 for location).
1. Align the connector with the port opening.
1. Remove the cover from the port opening, if present.
2. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Push the connector into the port until it is seated.
HEADPHONE JACK
4. Tighten the two hold-down screws, located on
each side of the connector.
The headphone jack allows you to connect headphones
or powered external speakers to your Tablet PC. Your
headphones or speakers must be equipped with a 1/8”
(3.5 mm) stereo mini-plug. In order to connect head-
phones or speakers follow these easy steps: (See Figure 2-
4 on page 10 for location)
When an external monitor is plugged in,
pressing the [Fn] + [F10] keys allows you
to change your selection of where to send
your display video. Each time you press the
key combination, you will step to the next
choice, starting with the built-in display
panel only, moving to the external monitor
only, finally moving to both the built-in
display panel and an external monitor.
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
If you plug headphones into the
headphone jack, the built-in stereo
speakers will be disabled.
EXTERNAL DVI PORT
The external Digital Video Interface (DVI) port on the
optional port replicator allows you to connect an
external digital monitor or projector. In order to connect
a DVI monitor follow these easy steps: (See Figure 4-11
on page 51 for location).
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on each
side of the connector.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Troubleshooting
55
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F i v e
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr o u b l e s h o o t i n g
8. If you have tried the solutions suggested in the
Troubleshooting Table and checked our Website for
possible solutions without success, contact your
support representative:
Troubleshooting
Your LifeBook T4200 Series Tablet PC is sturdy and
subject to few problems in the field. However, you may
encounter simple setup or operating problems that you
can solve on the spot, or problems with peripheral
devices, that you can solve by replacing the device. The
information in this section helps you isolate and resolve
some of these straightforward problems and identify
failures that require service.
Toll free: 1-800-8Fujitsu
E-mail: [email protected]
Website: http://www.computers.us.fujitsu.com/
support
Before you place the call, you should have the following
information ready so that the customer support repre-
sentative can provide you with the fastest possible solu-
tion:
IDENTIFYING THE PROBLEM
If you encounter a problem that you are having diffi-
culty in solving, go through the following procedure
before pursuing further troubleshooting:
■
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Type of device connected, if any
■
■
1. Turn off your Tablet PC.
■
■
■
■
2. Make sure the AC adapter is plugged into your
Tablet PC and to an active AC power source.
3. Make sure that any card inserted in the PC Card slot
is seated properly. You can also remove the card
from the slot, thus eliminating it as a possible cause
of failure.
See the Configuration Label on the bottom of your
Tablet PC for configuration and serial numbers. (See
figure 2-8 on page 15 for location)
4. Make sure that any devices connected to the external
connectors are plugged in properly. You can also
disconnect such devices, thus eliminating them as
possible causes of failure.
SPECIFIC PROBLEMS
Using the Troubleshooting Table
When you have problems with your tablet, try to find
the symptoms under the Problem column of the trou-
bleshooting table for the feature giving you difficulty.
5. Turn on your Tablet PC. Make sure it has been off at
least 10 seconds before you turn it on.
6. Go through the boot sequence.
7. If the problem has not been resolved, refer to the
Troubleshooting Table, that follows, for more
detailed troubleshooting information.
You will find a description of common causes for that
symptom under the column Possible Cause and what, if
anything, you can do to correct the condition under
Possible Solutions. All possible causes or solutions may
not apply to your Tablet PC.
8. If you still have the problem after taking all of the
above approaches, please check our Website at http:/
/www.computers.us.fujitsu.com/support for
possible known support issues.
■
If you keep notes about what you have
tried, your support representative may
be able to help you more quickly by giv-
ing additional suggestions over the
phone.
■
Do not return a failed Tablet PC to your
supplier until you have talked to a sup-
port representative.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F i v e
TROUBLESHOOTING TABLE
Problem
Page
Problem
Page
Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 58
Docking Problems . . . . . . . . . . . . . . . . . . . . . . . . page 58
Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 58
Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 58
Pen Input Problems . . . . . . . . . . . . . . . . . . . . . . . page 59
Infrared Problems . . . . . . . . . . . . . . . . . . . . . . . . page 59
Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 59
Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 59
USB Device Problems . . . . . . . . . . . . . . . . . . . . . page 60
PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 60
Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 60
Shutdown and Startup Problems . . . . . . . . . . . . page 62
Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 63
Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 64
Problem
Possible Cause
Possible Solutions
Audio Problems
There is no sound coming
The software volume control is Adjust the sound volume control settings in your
from the built-in speakers. set too low.
software, operating system and applications.
Headphones are plugged into
your Tablet PC.
Plugging in headphones disables the built-in
speakers, remove the headphones.
Software driver is not config-
ured correctly.
Refer to your application and operating system
documentation for help.
Sound could have been muted Press [F3] while holding the [Fn] key to toggle the
with function keys.
sound on and off.
Port Replicator Problems
Tablet PC does not turn on Port Replicator AC adapter is
Provide power to the Port Replicator.
Remove and re-dock your Tablet PC.
when installed in optional
Port Replicator
not plugged in.
Tablet PC is not properly
seated in the Port Replicator.
Hard Drive Problems
You cannot access your
hard drive.
The setup utility is incorrectly Revise BIOS settings to set the Primary Master
set for your internal (Primary correctly. See “BIOS Setup Utility” on page 39.
Master) hard drive.
The wrong drive designator
was used by an application
Verify drive designator used by application is in
use by the operating system. When the operating
when a bootable CD-ROM was system is booted from a CD, drive designations
used to start the Tablet PC.
are automatically adjusted.
Security is set so your oper-
ating system cannot be started
without a password.
Verify your password and security settings.
Keyboard or Mouse Problems
The built-in keyboard does The Tablet PC has gone into
Push the Suspend/Resume button.
not seem to work.
Standby mode.
Your application has locked
out your keyboard.
Try to use your integrated pointing device to restart
your system. If this fails, turn your Tablet PC off by
pressing the suspend/resume button for 10 seconds
or more, and then turn it back on.
The NumLock key has been
toggled on.
Press the NumLock key to toggle it off.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr o u b l e s h o o t i n g
Problem
Possible Cause
Possible Solutions
You have installed an
external keyboard or
mouse, and it does not
seem to work.
Your external device is not
properly installed.
Re-install your device. See “Device Ports” on page 53.
Your operating system soft-
ware is not set up with the
correct driver for that device.
Check your device and operating system docu-
mentation and activate the proper driver.
You have connected an
external keyboard or a
mouse and it seems to be
locking up the system.
Your operating system soft-
ware is not set up with the
correct driver for that device.
Check your device and operating system
documentation and activate the proper driver.
Your system has crashed.
Try to restart your Tablet PC. If that fails, turn off
the power by pressing the suspend/resume button
for at least 10 seconds, and then power back on.
Pen Input Problems
Cursor is not tracking the
pen
The system may be
uncalibrated
If the cursor on the screen appears to be misaligned
with the pen or is not accurately tracking the pen,
calibrate the pen. See “Calibrating the Pen” on
page 31.
Infrared Problems
Infrared data transfer is not The IrDA port on the system
Move the system so that there is a direct line-of-sight
path between the two ports.
working
can’t “see” the IrDA port on
the other device.
The system and the other
device are too far from each
other.
Move the system and the device so that they are
three feet or less from each other.
The viewing angle between the The viewing angle between the system port and the
devices is too great.
device port cannot be more than 15 degrees from a
center line between the IrDA port on the Tablet PC
and the IrDA port on the other device.
You are using an old version of The device with which you are trying to communi-
IrDA. cate must be compliant with IrDA standard 1.1.
There are possibly problems in Go to Start -> (All) Programs -> Accessories ->
one or both devices.
Communications -> New Connection Wizard.
Verify that “Set up an advanced connection” is
checked and follow the on-screen instructions.
Memory Problems
Your Power On screen, or
Info menu of the BIOS
setup utility information,
does not show the correct
amount of installed
memory.
Your memory upgrade module Turn off your Tablet PC. Remove and re-install your
is not properly installed.
memory upgrade module. See “Memory Upgrade
Module” on page 45.
You have a memory failure.
Check for Power On Self Test (POST) messages.
See “Power On Self Test Messages” on page 65.
Modem Problems
Messages about modem
operation.
Messages about modem
operation are generated by
whichever modem application
is in use.
See your application software documentation for
additional information.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F i v e
Problem
Possible Cause
Possible Solutions
Modem does not appear to Modem may not have been
Verify that the modem has been initialized by the
operating system. To do so, right-click on My
Computer and select the Hardware tab. Click
[Device Manager] and click on the “+” symbol that
appears next to Modems. Verify that your device is
listed as installed.
work.
initialized.
USB Device Problems
You have installed a USB
device, but your Tablet PC
does not recognize the
device, or the device does
not seem to work properly.
The device is not properly
installed.
Remove and re-install the device. See “Device Ports”
on page 53.
The device may have been
Close the application and restart your Tablet PC.
installed while an application
was running, so your Tablet PC
is not aware of its installation.
Your software may not have
the correct software driver
active.
See your software documentation and activate the
correct driver.
Your device and another device Check all I/O addresses located within the BIOS
are assigned the same I/O
address.
setup utility and any other installed hardware or
software to make sure there are no duplications.
PC Card Problems
A card inserted in the PC
The card is not properly
Remove and re-insert the card. See “PC Cards” on
Card slot does not work or inserted.
is locking up the system.
page 49.
The card may have been
Close the application and restart your Tablet PC.
inserted while an application
was running, so your Tablet PC
is not aware of its insertion.
Your software may not have
the correct software driver
active.
See your software documentation and activate the
correct driver.
Your PC Card device and
Check all I/O addresses located within the BIOS
another device are assigned the setup utility and any other installed hardware or
same I/O address.
software to make sure there are no duplications.
Power Failures
You turn on your Tablet PC The installed battery is
Check the Status Indicator Panel to determine the
and nothing seems to
happen.
completely discharged or there presence and condition of the battery. See “Status
is no power adapter (AC or
Auto/Airline) installed.
Indicator Panel” on page 16. Install a charged
battery or a Power adapter.
The battery is installed but is
faulty.
Use the Status Indicator Panel to verify the presence
and condition of the battery. See “Status Indicator
Panel” on page 16. If a battery is indicating a short,
remove that battery and operate from another
power source or replace that battery.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr o u b l e s h o o t i n g
Problem
Possible Cause
Possible Solutions
You turn on your Tablet PC The battery is low.
and nothing seems to
happen.
Check the Status Indicator Panel to determine the
presence and condition of the battery. See “Status
Indicator Panel” on page 16. Use a Power adapter
until the battery is charged.
(continued)
The AC or auto/airline adapter Verify that your adapter is connected correctly. See
is not plugged in properly.
“Power Sources” on page 35.
The Power adapter (AC or
auto/airline) is faulty.
Try a different Power adapter or install a charged
optional second battery.
The Power adapter (AC or
auto/airline) has no power
from the AC outlet, airplane
Move the AC cord to a different outlet, check for a
line switch or tripped circuit breaker for the AC
outlet. If you are using an auto/airline adapter in a
seat jack, or the car’s cigarette car make sure the ignition switch is in the On or
lighter.
Accessories position.
Your Tablet PC turns off all The power management
Press any button on the keyboard, or move the
mouse to restore operation. If that fails, push the
Suspend/Resume button. Check your power
management settings, or close your applications
and go to the Power Savings menu of the setup
utility to adjust the timeout values to better suit
your operation needs.
by itself.
parameters are set for auto
timeouts which are too short
for your operating needs.
You are operating on battery
Install a power adapter and then push the Suspend/
power only and have ignored a Resume button. See “Power Sources” on page 35.
low battery alarm until the
battery is at the dead battery
state and your machine has
gone into Dead Battery
Suspend mode.
You have a battery failure.
Verify the condition of the battery using the
Status Indicator panel, and replace or remove
any battery that is shorted. See “Status Indicator
Panel” on page 16.
Your power adapter has failed Make sure the adapter is plugged in and the outlet
or lost its power source.
has power.
Your Tablet PC will not
work on battery alone.
The battery is dead.
Replace the battery with a charged one or install a
Power adapter.
No battery is installed.
Install a charged battery.
The battery is improperly
installed.
Verify that the battery is properly connected by
re-installing them.
Your battery is faulty.
Verify the battery condition using the Status Indi-
cator panel and replace or remove any battery that is
shorted. See “Status Indicator Panel” on page 16.
The battery seems to
discharge too quickly.
You are running an application Use a power adapter for this application when at all
that uses a great deal of power possible.
due to frequent hard drive or
CD-ROM access, or use of a
modem or LAN PC card.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F i v e
Problem
Possible Cause
Possible Solutions
The battery seems to
discharge too quickly.
The power savings features
may be disabled.
Check the power management and/or setup utility
settings in the Power Savings menu and adjust
according to your operating needs.
(continued)
The brightness is turned all
the way up.
Turn down the brightness adjustment. The higher
the brightness the more power your display uses.
The battery is very old.
Replace the battery.
Replace the battery.
The battery has been exposed
to high temperatures.
The battery is too hot or too
cold.
Restore the Tablet PC to normal operating tempera-
ture. The Charging icon on the Status Indicator
panel will flash when the battery is outside its
operating range.
The AC Adapter is defective.
Replace with another AC Adapter to see if the
problem persists. Replace any defective AC
Adapters.
Shutdown and Startup Problems
The Suspend/Resume
button does not work.
The Suspend/Resume button
Enable the button from the setup utility.
is disabled from the Advanced
submenu of the Power menu
of the setup utility.
You did not hold the button
in long enough.
Hold the button longer. This may need to be a few
seconds if your application is preventing the CPU
from checking for button pushes.
There may be a conflict with
the application software.
Close all applications and try the button again.
The system powers up,
and displays power-on
information, but fails to
load the operating system.
The boot sequence settings of
the setup utility are not
compatible with your
configuration.
Set the operating source by pressing the [F2] key
while the Fujitsu logo is on screen, entering the
setup utility and adjusting the source settings from
the Boot menu. See “BIOS Setup Utility” on page 39.
You have a secured system
requiring a password to load
your operating system.
Make sure you have the right password. Enter the
setup utility and verify the Security settings and
modify them as accordingly. See “BIOS Setup
Utility” on page 39.
An error message is
displayed on the screen
during the Tablet PC boot
sequence.
Power On Self Test (POST) has See the Power On Self Test (POST) messages to
detected a problem.
determine the meaning and severity of the problem.
Not all messages are errors; some are simply status
indicators. See “Power On Self Test Messages” on
page 65.
Your system display won’t
The system may be password- Check the status indicator panel to verify that the
turn on when the system is protected.
turned on or when the
Security icon is blinking. If it is blinking, enter your
password.
system has resumed.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr o u b l e s h o o t i n g
Problem
Possible Cause
Possible Solutions
Your Tablet PC appears to
change setup parameters
when you start it.
BIOS setup changes were not
saved when you made them
and exited the BIOS setup
utility returning it to
Make sure you select Save Changes And Exit when
exiting the BIOS setup utility.
previous settings.
The BIOS CMOS back-up
battery has failed.
Contact your support representative for repairs.
This is not a user-serviceable part.
Video Problems
The built-in display is blank The angle of the display and
Move the display and the brightness control until
when you turn on your
Tablet PC.
the brightness settings are not you have adequate visibility.
adequate for your lighting
conditions.
The optional Port Replicator is Pressing [F10] while holding down the [Fn] key
attached, an external monitor allows you to change your selection of where to
is plugged in, and the Tablet
PC is set for an external
monitor only.
send your display video. Each time you press the
combination of keys you will step to the next
choice. The choices, in order are: built-in display
only, external monitor only, both built-in display
and external monitor.
The power management
timeouts may be set for very
short intervals and you failed
to notice the display come on
and go off again.
Press any button the keyboard, or move the mouse
to restore operation. If that fails, push the Suspend/
Resume button. (The display may be shut off by
Standby mode, Auto Suspend or Video Timeout)
The Tablet PC turned on
with a series of beeps and
your built-in display is
blank.
Power On Self Test (POST)
has detected a failure which
does not allow the display
to operate.
Contact your support representative.
Your system display won’t
The system may be password- Check the status indicator panel to verify that the
turn on when the system is protected.
turned on or when the
Security icon is blinking. If it is blinking, enter your
password.
system has resumed.
The display goes blank by
itself after you have been
using it.
The Tablet PC has gone into
Press a button on the keyboard, or move the mouse
to restore operation. If that fails, push the Suspend/
Resume button. Check your power management
settings, or close your applications and go to the
Power Savings menu of the setup utility to adjust the
timeout values to better suit your operation needs.
See “BIOS Setup Utility” on page 39.
Video Timeout, Standby
Mode, or Hibernate Mode
because you have not used it
for a period of time.
The power management time- Press any button on the keyboard, or move the mouse
outs may be set for very short
intervals and you failed to
notice the display come on
and go off again.
to restore operation. If that fails, push the Suspend/
Resume button. (The display may be shut off by
Standby Mode, Auto Suspend or Video Timeout)
The display does not close. A foreign object, such as a
paper clip, is stuck between the
Remove all foreign objects from the keyboard.
display and the keyboard.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F i v e
Problem
Possible Cause
Possible Solutions
The display has bright or
dark spots.
If the spots are very tiny and
few in number, this is normal
for a large LCD display.
This is normal; do nothing.
If the spots are numerous or
The display needs technical diagnosis; contact your
large enough to interfere with support representative.
your operation needs.
The application display
You are running an application When compensation is disabled, a clearer but
uses only a portion of your that does not support 800 x
smaller display for applications that do not support
screen and is surrounded
by a dark frame.
600/1024 x 768 pixel resolution 800 x 600/1024 x 768 pixel resolution will result. You
display and display compres-
sion is enabled.
can fill the screen but have less resolution by
changing your compensation setting. (See the Video
Features submenu, located within the Advanced
menu of the BIOS. See “BIOS Setup Utility” on
page 39.
You have connected an
external monitor and it
does not display any
information.
Your BIOS setup is not set to
Try toggling the video destination by pressing [Fn]
enable your external monitor. and [F10] together, or check your BIOS setup and
enable your external monitor. (See the Video
Features submenu, located within the Advanced
Menu of the BIOS. See “BIOS Setup Utility” on
page 39.
Your external monitor is not
properly installed.
Reinstall your device. See “External Video Port” on
page 54.
Your operating system soft-
ware is not set up with the
correct software driver for
that device.
Check your device and operating system
documentation and activate the proper driver.
You have connected an
external monitor and it
does not come on.
Your external monitor may not See your monitor documentation and the External
be compatible with your Tablet Monitor Support portions of the Specifications
PC.
section. See “Specifications” on page 77.
Miscellaneous Problems
An error message is
Application software often has See your application manual and help displays
displayed on the screen
during the operation of an displays.
application.
its own set of error message
screens for more information. Not all messages are
errors some may simply be status.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr o u b l e s h o o t i n g
*Keyboard controller error
POWER ON SELF TEST MESSAGES
The keyboard controller test failed. You may have to
replace your keyboard or keyboard controller but may
be able to use an external keyboard until then. Contact
your support representative.
The following is an alphabetic list of error-and-status
messages that Phoenix BIOS and/or your operating
system can generate and an explanation of each message.
Error messages are marked with an *. If an error
message is displayed that is not in this list, write it down
and check your operating system documentation both
on screen and in the manual. If you can find no
reference to the message and its meaning is not clear,
contact your support representative for assistance.
*Keyboard error
Keyboard not working. You may have to replace your
keyboard or keyboard controller but may be able to
use an external keyboard until then. Contact your
support representative.
nnnn Cache SRAM Passed
*Keyboard error nn
Where nnnn is the amount of system cache in kilobytes
successfully tested by the Power On Self Test. (This can
only appear if you have an SRAM PC Card installed.)
BIOS discovered a stuck key and displays the scan code
for the stuck key. You may have to replace your keyboard
but may be able to use an external keyboard until then.
Contact your support representative.
*Extended RAM Failed at offset: nnnn
Extended memory not working or not configured prop-
erly. If you have an installed memory upgrade module,
verify that the module is properly installed. If it is prop-
erly installed, you may want to check your Windows
Setup to be sure it is not using unavailable memory
until you can contact your support representative.
*Operating system not found
Operating system cannot be located on either drive A: or
drive C: Enter the setup utility and see if both the fixed
disk, and drive A: are properly identified and that the
boot sequence is set correctly. Unless you have changed
your installation greatly, the operating system should be
on drive C:. If the setup utility is correctly set, your hard
drive may be corrupted and your system may have to be
re-installed from your back up media.
nnnn Extended RAM Passed
Where nnnn is the amount of memory in kilobytes
successfully tested.
*Parity Check 1 nnnn
*Failing Bits: nnnn The hex number nnnn
Parity error found in the system bus. BIOS attempts to
locate the address and display it on the screen. If it
cannot locate the address, it displays “????”. This is a
potentially data destroying failure. Contact your
support representative.
This is a map of the bits at the memory address (in
System, Extended, or Shadow memory) which failed the
memory test. Each 1 (one) in the map indicates a failed
bit. This is a serious fault that may cause you to lose data
if you continue. Contact your support representative.
*Parity Check 2 nnnn
*Fixed Disk x Failure or Fixed Disk Controller
Failure (where x = 1-4)
Parity error found in the I/O bus. BIOS attempts to
locate the address and display it on the screen. If it
cannot locate the address, it displays “????”. This is a
potentially data destroying failure. Contact your
support representative.
The fixed disk is not working or not configured prop-
erly. This may mean that the hard drive type identified
in your setup utility does not agree with the type
detected by the Power On Self Test. Run the setup utility
to check for the hard drive type settings and correct
them if necessary. If the settings are OK and the message
appears when you restart the system, there may be a
serious fault which might cause you to lose data if you
continue. Contact your support representative.
*Press <F1> to resume, <F2> to SETUP
Displayed after any recoverable error message. Press
the [F1] key to continue the boot process or the [F2]
key to enter Setup and change any settings.
*Previous boot incomplete –
Default configuration used
*Invalid NVRAM media type
Problem with NVRAM access. In the unlikely case that
you see this message you may have some display prob-
lems. You can continue operating but should contact
your support representative for more information.
Previous Power On Self Test did not complete success-
fully. The Power On Self Test will load default values and
offer to run Setup. If the previous failure was caused by
incorrect values and they are not corrected, the next
boot will likely fail also. If using the default settings does
not allow you to complete a successful boot sequence,
you should turn off the power and contact your support
representative.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F i v e
*Real time clock error
Real-time clock fails BIOS test. May require board repair.
MODEM RESULT CODES
The operating system and application software that is
factory installed detects the modem characteristics and
provides the necessary command strings to operate the
modem. The internal modem operation is controlled by
generic AT commands from the operating system and
application software. The standard long form result
codes may, in some cases, be displayed on your screen to
keep you informed of the actions of your modem. The
operating system and application software may suppress
display of the result codes.
Contact your support representative.
*Shadow RAM Failed at offset: nnnn
Shadow RAM failed at offset nnnn of the 64k block at
which the error was detected. You are risking data
corruption if you continue. Contact your support repre-
sentative.
nnnn Shadow RAM Passed
Where nnnn is the amount of shadow RAM in kilobytes
successfully tested.
Examples of result codes are:
■
OK
*System battery is dead – Replace and run SETUP
The BIOS CMOS RAM memory hold up battery is dead.
This is part of your BIOS and is a board mounted
battery which requires a support representative to
change. You can continue operating but you will have to
use setup utility default values or reconfigure your setup
utility every time you turn off your Tablet PC.
■
NO CARRIER
NO DIALTONE
CONNECT 53000 (Connection complete
at 53,000 bps.)
ERROR
FAX
RING (This means an incoming call.)
BUSY
NO ANSWER
■
■
■
■
■
■
System BIOS shadowed
System BIOS copied to shadow RAM.
■
When using the internal modem with applications that
are not factory installed refer to the application
documentation.
*System CMOS checksum bad – run SETUP
BIOS CMOS RAM has been corrupted or modified
incorrectly, perhaps by an application program that
changes data stored in BIOS memory. Run Setup and
reconfigure the system.
*System RAM Failed at offset: nnnn
System memory failed at offset nnnn of in the 64k block
at which the error was detected. This means that there is
a fault in your built-in memory. If you continue to
operate, you risk corrupting your data. Contact your
support representative for repairs.
nnnn System RAM Passed
Where nnnn is the amount of system memory in
kilobytes successfully tested.
*System timer error
The timer test failed. The main clock that operates the
computer is faulty. Requires repair of system board.
Contact your support representative for repairs.
UMB upper limit segment address: nnnn
Displays the address of the upper limit of Upper
Memory Blocks, indicating released segments of the
BIOS memory which may be reclaimed by a virtual
memory manager.
Video BIOS shadowed
Video BIOS successfully copied to shadow RAM.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
T r o u b l e s h o o t i n g
4. In the list, check off all the components you want to
install. If you want to install all components, click
[Select All]. Clicking [Select All] will select all of the
blue-coded components; you must select grey and
green components separately.
Restoring Your
Pre-installed Software
The Drivers and Applications Restore (DAR) DVD
contains sets of device drivers and Fujitsu utilities (in
specific directories) that are unique to your Tablet PC
configuration for use as documented below.
5. Once you have selected the components you wish to
install, click [Install Selected Subsystems]; the
components will be installed.
6. After the components are installed, click [OK], then
click [Yes] when asked if you want to reboot the
system.
In order to install applications and/or
drivers from the DAR DVD, you will need
access to a DVD drive. If you do not have a
built-in DVD drive, you will need to connect
an external DVD drive to your system.
RESTORING THE FACTORY IMAGE
The Restore Disc that came with your system contains
two utilities:
■
If you have access to the internet, visit the
Fujitsu Support website at http://
www.computers.us.fujitsu.com/support to
check for the most current information,
drivers and hints on how to perform
recovery and system updates.
The Recovery utility allows you to restore the original
contents of the C: drive.
■
The Hard Disk Data Delete utility on this disc is used
to delete all data on your hard disk and prevent it from
being reused. Do not use Hard Disk Data Delete unless
you are absolutely certain that you want to erase your
entire hard disk, including all partitions.
RE-INSTALLING INDIVIDUAL
DRIVERS AND APPLICATIONS
The Drivers and Applications CD can be used to selec-
tively re-install drivers and/or applications that may have
• The use of this disc requires that you
have a device capable of reading DVDs
attached to your system. If you do not
have a built-in DVD player, you will need
to attach an external player. For more
information on available external devices,
visit our Website at: us.fujitsu.com/
computers.
been un-installed or corrupted.
There may be certain free third-party
applications pre-installed on your system
that are not on the DAR CD. The latest
versions of the applications can be
• This disc can only be used with the
system with which it was purchased.
downloaded from the third-party’s website.
BOOT Priority Change
To re-install drivers and/or applications:
Before restoring an image, you must first verify that your
system is set up to boot from the DVD drive. To verify/
change the boot-up priority (rather than booting-up
from the hard drive or an external floppy disk drive),
perform the following steps:
1. Boot up the system and insert the DAR CD after
Windows has started. A Fujitsu Installer screen is
displayed after the CD is inserted.
2. After reading the License Agreement, click [I agree].
3. A window will appear containing a list of applica-
tions, drivers, and utilities that you can install from
the Drivers and Applications CD.
1. Start your system and press the [F2] key when the
Fujitsu logo appears. You will enter the BIOS Setup
Utility.
2. Using the arrow keys, go to the Boot menu.
The components listed are color-coded in
terms of their install status. Blue indicates
that the component can be installed. Green
indicates that the component needs to be
installed separately. Grey indicates a
component that is already installed; grey
items can be reinstalled, but prior to
installation you will receive a reminder that
the component is already installed and may
need to be uninstalled prior to
3. Arrow down to the Boot Device Priority submenu.
Press [Enter].
4. If “Optical Media Drive” or “CD-ROM Drive” is not
at the top of the list, arrow down to the drive in the
list, and press the space bar (or the + key) to move it
to the top of the list. (The system attempts to boot
from the devices in the order in which they are
listed.). Note that the BIOS for some systems will
indicate “CD-ROM Drive”, even when a DVD drive
is connected.
reinstallation.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n F i v e
5. If you have an external DVD drive connected,
AUTOMATICALLY DOWNLOADING
DRIVER UPDATES
proceed to step 6; otherwise, proceed to step 7.
Your system has a convenient tool called the Fujitsu
Driver Update (FDU) utility. With FDU, you can choose
to automatically or manually go to the Fujitsu site to
check for new updates for your system.
6. If you have an external DVD drive connected:
■
Select the Advanced menu in the BIOS window.
Scroll down to the USB Features submenu and press
the Enter key to open it.
■
■
■
If Legacy USB Support is disabled, press the space
bar to enable it.
Scroll down to SCSI SubClass Support and press the
space bar to enable it.
The FDU icon should appear in the system tray at the
bottom right of your screen (roll the cursor over the
icons to find the correct one). If the FDU icon does not
appear in the system tray, it can be started by going to
[Start] -> All Programs, and clicking on Fujitsu Driver
Update; this will create the icon automatically.
7. Press [F10], then click on [Yes] to exit the BIOS
Setup Utility and return to the boot process.
After you have changed the boot priority, you can restore
a backup image when you are booting up.
To invoke the FDU menu, right-click on the FDU icon.
The menu contains the following items:
Procedure
■
Check for updates now
1. Turn on the power to your system.
Allows for manual driver update search. The first
time it is used, you are prompted to agree to a user
agreement. After clicking on the icon, the FDU auto-
matically connects with the Fujitsu site to check for
updates and downloads them. While downloading,
the icon has a red bar through it, indicating that it
cannot be used while the download is in process.
When the update is complete, a message appears
informing you of the fact.
2. Ensure that you have a device that can read DVDs
either installed in your system or attached exter-
nally to it.
3. Insert the Restore Disc into the drive tray.
4. Reboot your system.
WINDOWS VISTA USERS:
IMPORTANT NOTE - While the operating
system is booting up during the restoration
procedure, your screen will go blank for a
short period of time. This is normal. During
the period while your screen is blank, do
not press any buttons. Please wait for the
“Set Up Windows” screen to be displayed,
then follow the instructions that appear.
■
Enable Automatic Update Notifications
Automatically searches for new updates on a regular
basis (approximately every 3 days).
■
Show update history
Brings up a screen that displays a history of updates
that have been made via the FDU.
■
About Fujitsu Driver Update
5. After the system reboots, follow the instructions
that appear to either restore your system image or
erase all data from your hard disk.
Displays the FDU version number and copyright
information
■
Fujitsu Driver Update Readme
Displays the FDU readme.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Care and Maintenance
69
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S i x
70
Download from Www.Somanuals.com. All Manuals Search And Download.
C a r e a n d M a i n t e n a n c e
■
Do not operate the computer in areas where the air
vents can be obstructed, such as in tight enclosures or
on soft surfaces like a bed or cushion.
Care and Maintenance
If you use your Tablet PC carefully, you will increase its
life and reliability. This section provides some tips for
■
■
■
Always follow installation instructions closely.
Keep it away from food and beverages.
looking after the Tablet PC and its devices.
If you accidentally spill liquid on your Tablet PC:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
4. If your Tablet PC will not boot after it has dried
out, call your support representative.
■
The system contains components that
can be severely damaged by electro-
static discharge (ESD). To minimize risk
to the components, observe the
following precautions:
■
Before docking or undocking your
■
■
■
■
Do not use your Tablet PC in a wet environment (near
a bathtub, swimming pool).
LifeBook notebook (when using a port
replicator), it is a good practice to
always touch a grounded metal object
to discharge static electricity built up
in your body.
Always use the AC adapter and batteries that are
approved for your Tablet PC.
■
Avoid exposure to sand, dust and other environmental
hazards.
Be sure to power down your system
before adding or removing system
components. Even if the system is in
hibernate or standby states, data
could be lost or memory could be
damaged if power is still available to
the system.
Do not expose your Tablet PC to direct sunlight for
long periods of time at temperatures above 140° F
(60° C) may damage your Tablet PC.
■
■
Keep the covers closed on the connectors and slots
when they are not in use.
■
When installing or removing a
memory module, hold it by the edge
so as not to touch any contacts or
chips. Be careful not to touch any
internal computer terminals or compo-
nents; the oil from your fingers could
cause a short to the components.
If you are carrying your Tablet PC in a briefcase, or
any other carrying case, make sure that there are no
objects in the case pressing on the lid.
■
■
■
Do not drop your Tablet PC.
Do not put heavy or sharp objects on the computer.
Do not touch the screen with any sharp objects.
■
Electrical equipment may be hazardous if
misused. Operations of this product or
similar products, must always be super-
vised by an adult. Do not allow children
access to the interior of any electrical
products and do not permit them to
handle any cables.
Cleaning your Tablet PC
■
Always disconnect the power plug. (Pull the plug, not
the cord.)
■
Clean your Tablet PC with a damp, lint-free cloth. Do
not use abrasives or solvents.
LIFEBOOK T4200 SERIES TABLET PC
Caring for your Tablet PC
Your Tablet PC is a durable but sensitive electronic
■
Use a soft cloth to remove dust from the screen. Never
use glass cleaners.
■
device. Treat it with care.
Storing your Tablet PC
If storing your Tablet PC for a month or longer, turn
■
■
Make a habit of transporting it in a suitable carrying
case.
the Tablet PC off, fully charge the battery, then remove
and store all Lithium ion batteries.
■
Do not attempt to service the computer yourself. Any
■
unauthorized service performed on the computer will
void the warranty.
Store your Tablet PC and batteries separately. If you
store your Tablet PC with a battery installed, the bat-
tery will discharge, and battery life will be reduced. In
addition, a faulty battery might damage the Tablet PC.
■
To protect your computer from damage and to opti-
mize system performance, be sure to keep all air all
vents unobstructed, clean, and clear of debris. This
may require periodic cleaning, depending upon the
environment in which the system is used.
■
Store your Tablet PC in a cool, dry location.
Temperatures should remain between 13º F (-25º C)
and 140º F (60º C).
71
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S i x
Traveling with your Tablet PC
Do not transport your Tablet PC while it is turned on.
There is no repair for this problem other than replace-
ment. The solution is to become aware of the issue and
take appropriate steps to protect your keyboard.
■
■
Do not check your Tablet PC as baggage. Carry it with
you.
To clean the keyboard, use a rag dampened slightly with
cleaning solution. Use extreme care to prevent liquid
from dripping between the keys. Spraying directly on the
keys should be avoided. The spray should be applied first
to the cloth, and then the cloth wiped over the keys.
■
When traveling with the hard drive removed, wrap the
drive in a non-conducting materials (cloth or paper).
If you have the drive checked by hand, be ready to
install the drive if needed. Never put your hard drive
through a metal detector. Have your hard drive hand-
inspected by security personnel. You can however, put
your hard drive through a properly tuned X-ray
machine.
BATTERIES
Caring for your Batteries
■
Always handle batteries carefully.
■
■
Take the necessary plug adapters if you're traveling
overseas. Check the following diagram to determine
which adapter you'll need or ask your travel agent.
Do not short-circuit the battery terminals (that is, do
not touch both terminals with a metal object). Do not
carry loose batteries in a pocket or purse where they
may mix with coins, keys, or other metal objects.
Doing so may cause an explosion or fire.
Outlet Type
Location
■
Do not drop, puncture, disassemble, mutilate or incin-
United States, Canada, Mexico, parts
of Latin America, Japan, Korea, the
Philippines, Taiwan
erate the battery.
■
Recharge batteries only as described in this manual
and only in ventilated areas.
■
Do not leave batteries in hot locations for more than a
Russia and the Commonwealth of
Independent States (CIS), most of
Europe, parts of Latin America, the
Middle East, parts of Africa, Hong
Kong, India, most of South Asia
day or two. Intense heat can shorten battery life.
■
Do not leave a battery in storage for longer than six
months without recharging it.
Increasing Battery Life
Keep brightness to the lowest comfortable level.
United Kingdom, Ireland, Malaysia,
Singapore, parts of Africa
■
■
Set the power management for maximum battery life.
■
Put your Tablet PC in Standby mode when it is turned
China, Australia, New Zealand
on and you are not actually using it.
■
Limit your CD-ROM access.
■
Figure 6-1. Outlet types
Disable the Windows CD auto insert function.
■
Always use fully charged batteries.
KEYBOARD
Caring for your Keyboard
■
Eject PCMCIA cards when not in use.
The keyboard of your computer is a very sensitive
instrument. It is made up of many switches that are
activated when you press on the keys. The keyboard is a
major component of the heat dissipation system in a
Tablet PC. Due to heat and size considerations the
keyboard is not sealed. Because the keys are so close
together, it is not easy for the user to see when liquids
have fallen onto the circuitry below the keys.
OPTIONAL FLOPPY DISK DRIVE AND
FLOPPY DISKS
Caring for your Floppy Disks
■
Avoid using floppy disks in damp and dusty locations.
■
Never store a floppy disk near a magnet or magnetic
field.
■
Do not use a pencil or an eraser on a disk or disk label.
Attempting to clean the keyboard with a spray on
cleaner or rag soaked with cleaner the liquid can drip
onto the circuitry sight unseen. Once the liquid seeps
between the layers of circuitry, it can cause corrosion or
other damage to the circuits. This can result in keys
which no longer operate, or which, when pressed, record
the wrong characters and other similar failures.
■
Avoid storing the floppy disks in extremely hot or cold
locations, or in locations subject to severe temperature
changes. Store at temperatures between 50º F (10º C)
and 125º F (52º C).
■
Do not touch the exposed part of the disk behind the
metal shutter.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
C a r e a n d M a i n t e n a n c e
Caring for your Optional Floppy Disk Drive
To clean, wipe the floppy disk drive clean with a dry
Caring for your Optional Optical Drive
Your optical drive is durable but you must treat it with
■
soft cloth, or with a soft cloth dampened with water or
a solution of neutral detergent. Never use benzene,
paint thinner or other volatile material.
care. Please pay attention to the following points:
■
The drive rotates the compact disk at a very high
speed. Do not carry it around or subject it to shock or
vibration with the power on.
Avoid using or storing the drive where it will be
■
Avoid storing the floppy disk drive in extremely hot or
■
cold locations, or in locations subject to severe tem-
perature changes. Store at temperatures between 50º F
(10º C) and 125º F (52º C).
exposed to extreme temperatures.
Avoid using or storing the drive where it is damp or
■
dusty.
■
Keep the floppy disk drive out of direct sunlight and
away from heating equipment.
■
Use of a commercially-available lens cleaner kit is
recommended to maintain the drive lens.
Avoid using or storing the drive near magnets or
■
■
Avoid storing the floppy disk drive in locations subject
devices that generate strong magnetic fields.
Avoid using or storing the drive where it will be
subjected to shock or vibration.
Do not disassemble or dismantle the optical drive.
to shock and vibration.
■
■
Never use the floppy disk drive with any liquid, metal,
or other foreign matter inside the floppy disk drive
or disk.
■
■
Never disassemble or dismantle your floppy disk
PC CARDS
Caring for your PC Card Slots
drive.
PC Cards are durable, but you must treat them with
care. The documentation supplied with your PC Cards
provides specific information for caring for the cards.
OPTIONAL OPTICAL DRIVE AND DISCS
Caring for your discs
CDs and DVD discs are precision devices and will func-
When you don’t have a PC Card inserted in your system,
you should be sure to insert the PC Card slot inserts that
came with your system. These will help to keep dust and
dirt out of your system.
tion reliably if given reasonable care.
■
Always store your discs in their case when not in use.
■
Always handle discs by the edges and avoid touching
the surface.
■
Avoid storing any discs in extreme temperatures.
■
Do not bend discs or set heavy objects on them.
■
Do not spill liquids on discs.
■
Do not scratch discs.
■
Do not put a label on discs.
■
Do not get dust on discs.
■
Never write on the label surface with a ballpoint pen
or pencil. Always use a felt pen.
■
If a disc is subjected to a sudden change in tempera-
ture, cold to warm condensation may form on the sur-
face. Wipe the moisture off with a clean, soft, lint free
cloth and let it dry at room temperature. DO NOT use
a hair dryer or heater to dry discs.
■
If a disc is dirty, use only a disc cleaner or wipe it with
a clean, soft, lint free cloth starting from the inner
edge and wiping to the outer edge.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S i x
74
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Specifications
75
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S e v e n
76
Download from Www.Somanuals.com. All Manuals Search And Download.
S p e c i f i c a t i o n s
Specifications
LifeBook T4200 Series Tablet PC Specifications
This section provides the hardware and environmental
specifications for your LifeBook T4200 Series Tablet PC.
Specifications of particular configurations will vary.
L1 cache
64 KB on-die
(CPU)
L2 cache
2 MB or 4 MB on-die (depending on
CPU)
CONFIGURATION LABEL
Your LifeBook T4200 Series Tablet PC has a configura-
tion label located on the bottom. This label contains
information regarding the options you’ve chosen for
your Tablet PC. Following is an example label and infor-
mation on how to read your own configuration label.
1 MB (Boot Block Type Flash ROM)
BIOS ROM
Hard disk
drive
• 2.5” HDD
• Minimum 40 GB IDE (5400 rpm)
Also available:
60 GB (5400 rpm),
80 GB (5400 rpm),
Part Number
Configuration ID
100 GB (5400 rpm),
120 GB (5400 rpm)
• S-ATA 150
• Shock-mounted
• SMART Support
Configuration P/N: A1AXXXXXXXXXXXX
FPC P/N: FPCXXXXXX
T4220, T7100, 12.1 XGA, XPTE, 60G, 512M
Processor
Operating
System
Display Specifications
Memory
Hard Drive
Screen Size
Model
Display
12.1 TFT XGA (1024 x 768),
16M colors:
Figure 7-1. Configuration Label
•
•
•
•
•
Color LCD
Backlit
Active Digitizer
32-bit color
External monitor support: VGA
(1024 x 768 maximum)
Dot pitch: 0.240 x 0.240 mm
LifeBook T4200 Series Tablet PC Specifications
The specifications for your particular model may vary.
To determine the specifications for your system, please
visit our Website at: us.fujitsu.com/computers.
•
•
Viewing Angle:
Horizontal: 90 degrees (max.)
Vertical: 90 degrees (max.)
Physical Specifications
•
Optional Indoor/Outdoor
Viewability
Dimensions
11.61” w x 9.61” d x 1.44" / 1.48"
(295 mm x 244 mm x 36.5 / 37.5 mm)
Graphics
VRAM
Intel® Clear Video Technology (GMA
X3100)
Processing Specifications
CPU
Intel® Core™ 2 Duo processors
Your Tablet PC uses Dynamic Video
Memory Technology (DVMT), which
allows the video driver to dynamically
determine the amount of memory that
is used. The system uses the following
maximums for video functions:
Chipset
Intel GM965 + ICH8M, 800 MHz front
side bus
Memory/Storage Specifications
Main RAM
• 512 MB SDRAM (DDR2 667 MHz)
• 200-pin SO DIMM slots x 2
Windows XP: 128 MB
512 MB, 1 GB, and 2 GB modules
available, with a system maximum of 4
GB (2 GB x 2) Note that system may
display 3.2 GB of total memory when
two 2 GB modules are installed.
Windows Vista: 64 MB (with 512 MB
system memory); 256 MB (with 1 GB
system memory); 384 MB 9 with 1.5 GB
or more system memory).
Turbo
Memory
Optional Intel Turbo Memory:
512 MB or 1 GB
Interface Specifications
77
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S e v e n
LifeBook T4200 Series Tablet PC Specifications
LifeBook T4200 Series Tablet PC Specifications
Integrated
Interfaces
• Modem (RJ-11)
• LAN (RJ-45)
• USB 2.0 x 3
• DC-In
User
Interface
support
• Keyboard
Pitch: 19 mm, Stroke: 3 mm
• TouchPad pointing device with scroll
button
• Fingerprint Sensor Device
• Active digitizer with pen input
• On-screen keyboard
• IrDA
• Analog RGB, Mini D-SUB 15-pin
connector for external VGA monitor
• Docking connector
Audio
•
•
ALC 262
Interfaces
on
Optional
Port
• DC Power
Dual internal digital microphone
array with background noise
cancellation
• LAN (RJ-45)
• 15-pin D-SUB connector for external
VGA monitor
•
•
Stereo speaker x 2
Replicator
• DVI-D for external monitor
• USB 2.0 x 4
Mono microphone and stereo
headphone jacks
• Line Out
User
Controls
• Programmable Application Buttons,
each with primary and secondary
functions (default applications:
• Docking Port
PC Card
Slots
• One Type I or Type II
Microsoft Journal and Calculator)
• PCMCIA CardBus version 3.0
• Security button support
• Trusted Platform Module (TPM)
support
SD/
Memory
Stick Slot
One slot for SD/Memory Stick card
Dedicated slot for SmartCard
• Suspend/Resume button
Status
Indicators
(LCDs)
• Power
Smart Card
Slot
• Charge/DC-In
• Battery charging (x 2)
• Battery level (x 2)
• Wireless LAN/Bluetooth Switch
• Optical drive
• Hard disk drive
• Caps Lock
Modular
Bay
Devices
One of the following devices is pre-
installed:
• Dual-Layer Multi-Format DVD Writer:
DVD-ROM Read: CAV 8x Speed
DVD-RAM Read/Write: ZCLV 5x
Speed
• Num Lock
• Scroll Lock
DVD-R Write: CAV 8x Speed
DVD-R DL Write: ZCLV 4x Speed
• Security
DVD-RW Write: ZCLV 6x Speed
DVD+R Write: CAV 8x Speed
Communications
Modem
Internal V.90 standard 56K fax/modem
(ITU V.90, 56K data, 14.4K fax)
DVD+R DL Write: ZCLV 4x Speed
DVD+RW Write: ZCLV 8x Speed
CD-ROM Read: CAV 24x Speed
CD-R Write: ZCLV 24x Speed
Gigabit
LAN
Internal wired 10/100/1000 Gigabit
Ethernet LAN
CD-RW Write: CLV 10x Speed
• DVD-ROM Drive: 8x DVD-ROM
Wireless
LAN
• Optional Integrated Intel PRO/
Wireless 4965AGN, Wi-Fi-
compliant, or,
• DVD/CD-RW Combo Drive:
8x DVD-ROM, 24x CD-R, 10x CD-
RW, 24x CD-ROM
• Optional Atheros SuperAG™
(802.11a/b/g) wireless LAN with
Antenna On/Off switch
• Modular Bay Battery
• Weight Saver
(Note that at the time of publication of
this document, the 802.11n standard
has not yet been ratified, and is still in
draft stage.)
Infrared
• System IR Port
• IrDA version 1.1 (FIR, 4 Mbps)
78
Download from Www.Somanuals.com. All Manuals Search And Download.
S p e c i f i c a t i o n s
LifeBook T4200 Series Tablet PC Specifications
LifeBook T4200 Series Tablet PC Specifications
Bluetooth
Device
Optional Bluetooth device for wireless
personal area network communication
• EN55022 (CISPR22) Class B
• FCC 15, Class B
• FCC 15C, 15.247
• ICES-003
Power Specifications
Main
• 6-cell
Emissions
• Canada RSS-210
Battery
• Removable, Lithium ion
• 10.8 V @5200 mAh, max. 56 WHr
• Warm-swappable
• ETSI EN 300 328-1 V1.3.1 : 2001
• ETSI EN 300 328-2 V1.2.1 : 2001_12
• ETSI EN 301 498-17 V1.2.1 : 2002
• ETSI EN 301 498-1 V1.4.1 : 2002
Optional
Bay Battery
•
•
•
6-cell
Removable, Lithium ion
10.8V @ 3800 mAh, max. 41.0 WHr
• EN55024 (1998)
Immunity
Safety
• UL and cUL Listed, UL 60950-1
• 6-cell NiMH, 35 mAh
Bridge
Battery
• Life (with Suspend-to-RAM on
bridge battery only):
5 minutes from full charge
• FCC Part 68
• IC CS-03
Telecom
Additional Specifications
Autosensing 100 - 240V, supplying 19
VDC, with a current of 4.22 A
AC
Adapter
• Microsoft® Windows® XP
Tablet PC Edition 2005 with
OneNote 2007
Operating
systems
Environmental Specifications
• Microsoft WIndows Vista™
Business with OneNote 2007
Temperatur
e
Operating: 41o to 95o F (5o to 35o C)
Non-operating: 5o to 140o F
(-15o to 60o C)
Operating:
Humidity
20 to 80% non-condensing
Non-operating:
8 to 85% non-condensing
Agency Approval Specifications
79
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S e v e n
80
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Glossary
81
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S e v e n
result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as
determined by the total RENs, contact the local tele-
phone company.
Regulatory Information
Changes or modifications not expressly
approved by Fujitsu could void this user’s
authority to operate the equipment
If this equipment causes harm to the telephone network,
the telephone company will notify you in advance that
temporary discontinuance of service may be required.
But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
FCC NOTICES
Notice to Users of Radios and Television
These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
The telephone company may make changes in its facili-
ties, equipment, operations or procedures that could
effect the operation of the equipment. If this happens
the telephone company will provide advance notice in
order for you to make necessary modifications to main-
tain uninterrupted service.
If trouble is experienced with this equipment, for repair
or warranty information, please refer to the manual or
contact Fujitsu Computer Systems Corporation,
Customer Service. If the equipment is causing harm to
the telephone network, the telephone company may
request that you disconnect the equipment until the
problem is resolved.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
•
•
Connect the equipment into an outlet that is on a
different circuit than the receiver.
Consult the dealer or an experienced radio/TV
technician for help.
The equipment cannot be used on public coin service
provided by the telephone company. Connection to
party line service is subject to state tariffs. (Contact the
state public utility commission, public service commis-
sion or corporation commission for information).
Shielded interconnect cables must be employed with this
equipment to ensure compliance with the pertinent RF
emission limits governing this device.
Notice to Users of the US Telephone Network
If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation
of this computer does not disable your alarm equip-
ment. If you have any questions about what will disable
alarm equipment, consult your telephone company or a
qualified installer.
This equipment complies with Part 68 of the FCC rules.
On the bottom of this equipment is a label that contains,
among other information, the FCC registration number
and ringer equivalence number (REN) for this equip-
ment. If requested, this information must be provided to
the telephone company.
The Telephone Consumer Protection Act of 1991 makes
it unlawful for any person to use a computer or other
electronic device to send any message via a telephone fax
machine unless such message clearly contains in a
margin at the top or bottom of each transmitted page or
on the first page of the transmission, the date an time it
is sent and an identification of the business or other
entity, or other individual sending the message and the
telephone number of the sending machine or such busi-
ness, other entity, or individual.
This equipment is designed to be connected to the tele-
phone network or premises wiring using a standard jack
type USOC RJ11C. A plug and jack used to connect this
equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided
with this product. It is designed to be connected to a
compatible modular jack that is also compliant.
The ringer equivalent number (REN) of this equipment
is 0.1B as shown on the label. The REN is used to deter-
mine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone may
82
Download from Www.Somanuals.com. All Manuals Search And Download.
R e g u l a t o r y I n f o r m a t i o n
DOC (INDUSTRY CANADA) NOTICES
Avis Aux Utilisateurs Du Réseau
Notice to Users of Radios and Television
Téléphonique Canadien
This Class B digital apparatus meets all requirements of
Canadian Interference-Causing Equipment Regulations.
AVIS: Le présent matériel est conforme aux spécifica-
tions techniques d’Industrie Canada applicables au
matériel terminal. Cette conformité est confirmée par le
numéro d’enregistrement. Le sigle IC, placé devant le
numéro d’enregistrement (4005B-DELPHI), signifie que
l’enregistrement s’est effectué conformément à une
déclaration de conformité et indique que les spécifica-
tions techniques d’Industrie Canada ont été respectées.
Il n’implique pas qu’Industrie Canada a approuvé le
matériel.
CET appareil numérique de la class B respecte toutes les
exigence du Réglement sur le matérial brouilleur du
Canada.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry
Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The
abbreviation, IC, before the registration number
(4005B-DELPHI) signifies that registration was
performed based on a Declaration of Conformity indi-
cating that Industry Canada technical specifications
were met. It does not imply that Industry Canada
approved the equipment.
Avant de connecter cet équipement à une ligne télépho-
nique, l’utilisateur doit vérifier s’il est permis de
connecter cet équipement aux installations de télécom-
munications locales. L’utilisateur est averti que même la
conformité aux normes de certification ne peut dans
certains cas empêcher la dégradation du service.
Before connecting this equipment to a telephone line the
user should ensure that it is permissible to connect this
equipment to the local telecommunication facilities. The
user should be aware that compliance with the certifica-
tion standards does not prevent service degradation in
some situations.
Les réparations de l’équipement de télécommunications
doivent être effectuées par un service de maintenance
agréé au Canada. Toute réparation ou modification, qui
n’est pas expressément approuvée par Fujitsu, ou toute
défaillance de l’équipement peut entraîner la compagnie
de télécommunications à exiger que l’utilisateur décon-
necte l’équipement de la ligne téléphonique.
Repairs to telecommunication equipment should be
made by a Canadian authorized maintenance facility.
Any repairs or alterations not expressly approved by
Fujitsu or any equipment failures may give the telecom-
munication company cause to request the user to
disconnect the equipment from the telephone line.
AVIS: L’indice d’équivalence de la sonnerie (IES) du
présent matériel est de 0.1B. L’IES assigné à chaque
dispositif terminal indique le nombre maximal de
terminaux qui peuvent être raccordés à une interface
téléphonique. La terminaison d’une interface peut
consister en une combinaison quelconque de dispositifs,
à la seule condition que la somme d’indices d’équiva-
lence de la sonnerie de tous les dispositifs n’excède pas 5.
NOTICE: The Ringer Equivalence Number (REN) for
this terminal equipment is 0.1B. The REN assigned to
each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected
to a telephone interface. The termination on an interface
may consist of any combination of devices subject only
to the requirement that the sum of the Ringer Equiva-
Pour assurer la sécurité, les utilisateurs
doivent vérifier que la prise de terre du ser-
vice d’électricité, les lignes télphoniques et
les conduites d’eau métalliques sont con-
nectées ensemble. Les utilisateurs NE
doivent PAS tenter d’établir ces connex-
ions eux-mêmes, mais doivent contacter
les services d’inspection d’installations
électriques appropriés ou un électricien.
Ceci peut être particulièrement important
en régions rurales.
lence Numbers of all the devices does not exceed five.
For safety, users should ensure that the
electrical ground of the power utility, the
telephone lines and the metallic water
pipes are connected together. Users should
NOT attempt to make such connections
themselves but should contact the appro-
priate electric inspection authority or elec-
trician. This may be particularly important
in rural areas.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n S e v e n
84
Download from Www.Somanuals.com. All Manuals Search And Download.
G l o s s a r y
Glossary
AC Adapter
Cache Memory
A device which converts the AC voltage from a wall
outlet to the DC voltage needed to power your Tablet
PC.
A block of memory built into the micro-processor
which is much faster to access than your system RAM
and used in specially structured ways to make your
overall data handling time faster.
ACPI
Advanced Configuration and Power Interface
CardBus
A faster, 32-bit version of the PC Card interface which
offers performance similar to the 32-bit PCI
architecture.
Active-Matrix Display
A type of technology for making flat-panel displays
which has a transistor or similar device for every pixel
on the screen.
CD-ROM
Compact disk read only memory. This is a form of
digital data storage which is read optically with a laser
rather than a magnetic head. A typical CD-ROM can
contain about 600MB of data and is not subject to heads
crashing into the surface and destroying the data when
there is a failure nor to wear from reading.
AdHoc
A designation for wireless LAN network configuration.
It indicates a form of communication limited to those
personal computers which have wireless LAN function.
ADSL
Channel
Asymmetric Digital Subscriber Line
The frequency band of wireless LAN to be used in
communications over wireless LAN or at the access
point.
Technology for transporting high bit-rate services over
ordinary phone lines.
Auto/Airline Adapter
CMOS RAM
A device which converts the DC voltage from an auto-
mobile cigarette lighter or aircraft DC power outlet to
the DC voltage needed to power your Tablet PC.
Complementary metal oxide semiconductor random
access memory. This is a technology for manufacturing
random access memory which requires very low levels of
power to operate.
BIOS
Basic Input-Output System. A program and set of
default parameters stored in ROM which tests and
operates your Tablet PC when you turn it on until it
loads your installed operating system from disk. Infor-
mation from the BIOS is transferred to the installed
operating system to provide it with information on the
configuration and status of the hardware.
Command
An instruction which you give your operating system.
Example: run a particular application or format a floppy
disk.
Configuration
The combination of hardware and software that makes
up your system and how it is allocated for use.
Bit
An abbreviation for binary digit. A single piece of
information which is either a one (1) or a zero (0).
CRT
Cathode Ray Tube. A display device which uses a beam
of electronic particles striking a luminescent screen. It
produces a visual image by varying the position and
intensity of the beam.
bps
An abbreviation for bits per second. Used to describe
data transfer rates.
Data
Boot
The information a system stores and processes.
To start-up a computer and load its operating system
from disk, ROM or other storage media into RAM.
DC
Direct current. A voltage or current that does not
Bus
fluctuate periodically with time.
An electrical circuit which passes data between the CPU
and the sub-assemblies inside your Tablet PC.
Default Value
A pre programmed value to be used if you fail to set
Byte
your own.
8 bits of parallel binary information.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n E i g h t
DHCP
Dynamic Host Configuration Protocol
ECP
Extended Capability Port. A set of standards for high
speed data communication and interconnection
between electronic devices.
A protocol used for automatically fetching communica-
tion parameters such as IP addresses. The side which
assigns IP address is called DHCP server and the side
that is assigned it is called DHCP client.
Encryption Key (Network Key)
Key information used to encode data for data transfer.
This device uses the same encryption key to encode and
decode the data, and the identical encryption key is
required between the sender and receiver.
DIMM
Dual-in-line memory module.
Disk
ESD
A spinning platter of magnetic data storage media. If the
platter is very stiff it is a hard drive, if it is highly flexible
it is a floppy disk, if it is a floppy disk in a hard housing
with a shutter it is commonly called a diskette.
Electro-Static Discharge. The sudden discharge of elec-
tricity from a static charge which has built-up slowly.
Example: the shock you get from a doorknob on a dry
day or the sparks you get from brushing hair on a dry
day.
Disk Drive
The hardware which spins the disk and has the heads
and control circuitry for reading and writing the data
on the disk.
Extended Memory
All memory more than the 640KB recognized by
MS-DOS as system memory.
Diskette
FCC
A floppy disk in a hard housing with a shutter.
Federal Communication Commission.
DMA
Floppy Disk
Direct Memory Access
A spinning platter of magnetic data storage media which
is highly flexible.
Special circuitry for memory to memory transfers of
data which do not require CPU action.
GB
Gigabyte.
DMI
Desktop Management Interface
Hard drive
A standard that provides PC management applications
with a common method of locally or remotely querying
and configuring PC computer systems, hardware and
software components, and peripherals.
A spinning platter of magnetic data storage media where
the platter is very stiff.
I/O
Input/Output. Data entering and leaving your Tablet PC
in electronic form.
DNS
Domain Name System
I/O Port
A function that controls the correspondence of IP
addresses assigned to a computer with the name. Even
for those computers whose IP addresses are unknown, if
their names are known, it is possible to communicate
with them.
The connector and associated control circuits for data
entering and leaving your Tablet PC in electronic form.
IDE
Intelligent Drive Electronics. A type of control interface
for a hard drive which is inside the hard drive unit.
DOS
Disk Operating System (MS-DOS is a Microsoft Disk
IEEE802.11a
Operating System).
One of the wireless LAN standards prescribed by the 802
committee in charge of establishing standards of LAN
technology in IEEE (Institute of Electrical and Electronic
Engineers). This standard allows communications at the
maximum speed of 54 Mbps by using a 5 GHz band
which can freely be used without radio communication
license.
Driver
A computer program which converts application and
operating system commands to external devices into the
exact form required by a specific brand and model of
device in order to produce the desired results from that
particular equipment.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
G l o s s a r y
IEEE802.11b
LAN
One of the wireless LAN standards prescribed by 802
committee in charge of establishing standards of LAN
technology in IEEE (Institute of Electrical and Elec-
tronic Engineers). It allows communications at the
maximum speed of 11 Mbps by a band of 2.4 GHz (ISM
band) which can freely be used without radio communi-
cation license.
Local Area Network
An interconnection of computers and peripherals
within a single limited geographic location which can
pass programs and data amongst themselves.
LCD
Liquid Crystal Display
IEEE802.11g
A type of display which makes images by controlling the
orientation of crystals in a crystalline liquid.
One of the wireless LAN standards prescribed by 802
committee in charge of establishing standards of LAN
technology in IEEE (Institute of Electrical and Elec-
tronic Engineers). It allows communications at the
maximum speed of 54 Mbps by a band of 2.4 GHz (ISM
band) which can freely be used without radio communi-
cation license.
Lithium ion Battery
A type of rechargeable battery which has a high power-
time life for its size and is not subject to the memory
effect as Nickel Cadmium batteries.
LPT Port
Line Printer Port. A way of referring to parallel interface
ports because historically line printers were the first and
latter the most common device connected to parallel
ports.
Infrared
Light just beyond the red portion of the visible light
spectrum which is invisible to humans.
Infrastructure
MAC Address
A designation of Wireless LAN network configurations.
It indicates a form of communication using an Access
Point.
Media Access Control Address
A unique physical address of a network card. For
Ethernet, the first three bytes are used as the vendor
code, controlled and assigned by IEEE. The remaining
three bytes are controlled by each vendor (preventing
overlap), therefore, every Ethernet card is given a unique
physical address in the world, being assigned with a
different address from other cards. For Ethernet, frames
are sent and received based on this address.
IP Address
An address used for computers to communicate in the
TCP/IP environment.
Current IPv4 (version 4) uses four values in the range
between 1 and 255. (Example: 192.168.100.123).
There are two types of IP address: global address and
private address.
MB
Megabyte.
The global address is an only address in the world. It is
controlled by JPNIC (Japan Network Information
Center). A private address is an only address in the
closed network.
Megahertz
1,000,000 cycles per second.
Memory
IR
A repository for data and applications which is readily
An abbreviation for infrared.
accessible to your Tablet PC’s CPU.
IrDA
MHz
Infrared Data Association. An organization which
produces standards for communication using infrared
as the carrier.
Megahertz.
MIDI
Musical Instrument Digital Interface. A standard
communication protocol for exchange of information
between computers and sound producers such as
synthesizers.
IRQ
Interrupt Request
An acronym for the hardware signal to the CPU that an
external event has occurred which needs to be
processed.
Modem
A contraction for MOdulator-DEModulator. The
equipment which connects a computer or other data
terminal to a communication line.
KB
Kilobyte.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n E i g h t
Monaural
Partition
A system using one channel to process sound from all
sources.
A block of space on a hard drive which is set aside and
made to appear to the operating system as if it were a
separate disk, and addressed by the operating system
accordingly.
MPU-401
A standard for MIDI interfaces and connectors.
PCI
MTU
Peripheral Component Interconnect
Maximum Transmission Unit
Self-configuring PC local bus. Designed by Intel, PCI has
gained wide acceptance as a standard bus design.
The maximum data size that can be transferred at a time
through the Internet or other networks. You can set a
smaller MTU size to obtain successful communication,
if you have difficulty transferring data due to the fact
that the maximum size is too large.
PCMCIA
PCMCIA is a trademark of the Personal Computer
Memory Card International Association. The Personal
Computer Memory Card International Association is an
organization that sets standards for add-in cards for
personal computers.
Network authentication
The method of authentication performed by wireless
LAN clients to connect with the access point. There are
two types: open system authentication and shared key
authentication. The type of authentication must be set
to each client and also coincide with the setting of access
point with which to communicate. Network authentica-
tion is sometimes called authentication mode.
Peripheral Device
A piece of equipment which performs a specific function
associated with but not integral to a computer.
Examples: a printer, a modem, a CD-ROM.
Pitch (keyboard)
Network key
The distance between the centers of the letter keys of a
Data that is used for encrypting data in data communi-
cation. The personal computer uses the same network
key both for data encryption and decryption, therefore,
it is necessary to set the same network key as the other
side of communication.
keyboard.
Pixel
The smallest element of a display, a dot of color on your
display screen. The more pixels per area the clearer your
image will appear.
Network name (SSID: Security Set Identifier)
When a wireless LAN network is configured, grouping is
performed to avoid interference or data theft. This
grouping is performed with “Network name (SSID)”. In
order to improve security, the network key is set
allowing no communication unless “Network name
(SSID)” coincides with the network key.
POST
Power On Self Test. A program which is part of the BIOS
which checks the configuration and operating condition
of your hardware whenever power is applied to your
Tablet PC. Status and error messages may be displayed
before the operating system is loaded. If the self test
detects failures that are so serious that operation can not
continue, the operating system will not be loaded.
NTSC
National TV Standards Commission. The standard for
TV broadcast and reception for the USA.
PPPoE
Point to Point Protocol over Ethernet.
Open system authentication
A protocol for Ethernet, using a Point-to-Point Protocol
(PPP), which is used for connection on the phone line.
One of network authentication types for wireless LAN.
Since there is no check of network key upon authentica-
tion, clients can connect to the access point without
submitting correct network keys. However, in case of
actual communications, the same network key must be
set. Open system authentication is sometimes called
Open key authentication.
Program
An integrated set of coded commands to your
computers telling your hardware what to do and how
and when to do it.
Protocol
Operating System
Procedures and rules use to send and receive data
between computers, including the method of sending
and receiving data and the process used to handle
communication errors
A group of control programs that convert application
commands, including driver programs, into the exact
form required by a specific brand and model of micro-
processor in order to produce the desired results from
that particular equipment.
Conditions required for communication are organized
in procedures for correct transfer of information.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
G l o s s a r y
RAM
SRAM
Random Access Memory. A hardware component of
your Tablet PC that holds binary information (both
program and data) as long as it has the proper power
applied to it.
Static random access memory. A specific technology of
making RAM which does not require periodic data
refreshing.
SSID
RAM Module
Service Set Identifier
A printed circuit card with memory and associated
circuitry which allows the user to add additional
memory to the computer without special tools.
Specifies which network you are joining. Some systems
allow you to specify any SSID as an option so you can
join any network.
Reset
Standby
The act of reloading the operating system. A reset erases
To make inoperative for a period of time. Your Tablet PC
uses various suspension states to reduce power
consumption and prolong the charge of your battery.
all information stored in RAM.
Restart
See Reset.
Status Indicator
Resume
A display which reports the condition of some portion
of your hardware. On your Tablet PC this is an LCD
screen just above the keyboard.
To proceed after interruption. In your Tablet PC this
refers to returning to active operation after having been
in one of the suspension states.
Stereo (audio)
ROM
A system using two channels to process sound from two
Read Only Memory. A form of memory in which infor-
mation is stored by physically altering the material. Data
stored in this way can not be changed by your Tablet PC
and does not require power to maintain it.
different sources.
Subnet mask
TCP-IP network is controlled by being divided into
multiple smaller networks (subnets). IP address consists
of the subnet address and the address of each computer.
Subnet mask defines how many bits of IP address
comprise the subnet address. The same value shall be set
among computers communicating with each other.
SDRAM
Synchronous Dynamic Random Access Memory.
Serial Port
A connection to another device through which data is
transferred one bit at a time on a single wire with any
other wires only for control of the device not for transfer
of data.
SVGA
Super VGA.
S-Video
Shared key authentication
Super Video. A component video system for driving a
One of the network authentication types for wireless
LAN. Upon authentication, the access point checks
whether the same network key is set to the client. If the
client uses a wrong network key or the network key itself
is not set, authentication is unsuccessful, allowing no
communications with the access point.
TV or computer monitor.
SXGA+
Short for Super Extended Graphics Array, a display
specification that is capable of displaying 1400 x 1050
resolution.
System Clock
SMART
An oscillator of fixed precise frequency which synchro-
nizes the operation of the system and is counted to
provide time of day and date.
Self-Monitoring, Analysis and Reporting Technology
(SMART) is a technology that provides near-term
failure predictions for hard drives. When SMART is
enabled the hard drive monitors pre-determined drive
attributes that are susceptible to degradation over time.
If a failure is likely to occur, SMART makes a status
report available so that the Tablet PC can prompt the
user to back up the data on the drive. Naturally not all
failures are predictable. SMART predictability is limited
to those attributes which the drive can self-monitor. In
those cases where SMART can give advance warning, a
considerable amount of precious data can be saved.
TCP/IP
Transmission Control Protocol/Internet Protocol.
A standard Internet protocol that is most widely used.
TFT
Thin Film Transistor – A technology for flat display
panels which uses a thin film matrix of transistors to
control each pixel of the display screen individually.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
S e c t i o n E i g h t
UL
Underwriters Laboratories – An independent organiza-
tion that tests and certifies the electrical safety of devices.
USB
Universal Serial Bus.
Standard that allows you to simultaneously connect up
to 127 USB devices such as game pads, pointing devices,
printers, and keyboards to your computer.
VGA
Video Graphics Array. A video display standard
originally introduced by IBM with the PS/2 series of
personal computers.
VRAM
Video Random Access Memory. A memory dedicated to
video display data and control.
WFM
Wired for Management is Intel’s broad-based initiative
to reduce the total cost of ownership (TCO) of business
computing without sacrificing power and flexibility.
Wi-Fi Compatible
Wi-Fi (Wireless Fidelity) Identifies that the product has
passed the interoperability test, supplied by the WECA
(Wireless Ethernet Compatibility Alliance), which guar-
antees the interoperability of wireless IEEE 802.11 LAN
products. For more information on the Wi-Fi standard,
go to the WECA website at: www.wirelessethernet.com.
WLAN
Wireless Local Area Network. A wireless interconnection
of computers and peripherals within a single limited
geographic location which can pass programs and data
amongst themselves.
Write Protect
Prevent alteration of the binary state of all bits in a
storage media. Example: all information on a device
such as a floppy diskette; a block of space in a storage
media such as a partition of a hard drive; a file or direc-
tory of floppy diskette or hard drive.
XGA
Extended VGA.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Integrated Wireless
LAN* User’s Guide
*Optional Device
91
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
92
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the equipment and the
receiver.
FCC REGULATORY INFORMATION
Please note the following regulatory information related to the
wireless LAN device.
3. Connect the equipment to an outlet on a circuit different
from the one the receiver is connected to.
4. Consult the dealer or an experienced technician for help.
Regulatory Notes and Statements
Wireless LAN, Health and Authorization for use
FCC Radio Frequency Exposure statement
Radio frequency electromagnetic energy is emitted from Wireless
LAN (WLAN) devices. The energy levels of these emissions,
however, are far much less than the electromagnetic energy emis-
sions from wireless devices such as mobile phones. Wireless LAN
devices are safe for use by consumers because they operate within
the guidelines found in radio frequency safety standards and
recommendations. The use of Wireless LAN devices may be
restricted in some situations or environments, such as:
The available scientific evidence does not show that any health
problems are associated with using low power wireless devices.
There is no proof, however, that these low power wireless devices
are absolutely safe. Low power wireless devices emit low levels of
radio frequency energy (RF) in the microwave range while being
used. Whereas high levels of RF can produce health effects (by
heating tissue), exposure to low-level RF that does not produce
heating effects causes no known adverse health effects. Many
studies of low-level RF exposure have not found any biological
effects. Some studies have suggested that some biological effects
might occur, but such findings have not been confirmed by addi-
tional research. The wireless LAN radio device has been tested
and found to comply with FCC radiation exposure limits set forth
for an uncontrolled equipment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65.
The maximum SAR value measured from the devices are:
■
On board an airplane, or
In an explosive environment, or
In situations where the interference risk to other devices or ser-
vices is perceived or identified as harmful.
■
■
In cases in which the policy regarding use of Wireless LAN devices
in specific environments is not clear (e.g., airports, hospitals,
chemical/oil/gas industrial plants, hospitals, private buildings),
obtain authorization to use these devices prior to operating the
equipment.
■
Intel PROSet Wireless LAN (WM4965AGN): <1.59 W/kg
Regulatory Information/Disclaimers
■
Intel PROSet Wireless LAN (WM4965AGN) + Bluetooth
Installation and use of this Wireless LAN device must be in strict
accordance with the instructions included in the user documenta-
tion provided with the product. Any changes or modifications
made to this device that are not expressly approved by the manu-
facturer may void the user’s authority to operate the equipment.
The manufacturer is not responsible for any radio or television
interference caused by unauthorized modification of this device,
or the substitution or attachment of connecting cables and equip-
ment other than those specified by the manufacturer. It is the
responsibility of the user to correct any interference caused by
such unauthorized modification, substitution or attachment. The
manufacturer and its authorized resellers or distributors will
assume no liability for any damage or violation of government
regulations arising from failure to comply with these guidelines.
This device must not be co-located or operating in conjunction
with any other antenna or transmitter.
Simultaneous: <1.59 W/kg
■
Atheros Wireless LAN (AR5BXB6): <1.59 W/kg
■
Atheros Wireless LAN (AR5BXB6) + Bluetooth
Simultaneous: <1.59 W/kg
Export restrictions
This product or software contains encryption code which may
not be exported or transferred from the US or Canada without an
approved US Department of Commerce export license. This
device complies with Part 15 of FCC Rules., as well as ICES 003 B
/ NMB 003 B. Operation is subject to the following two condi-
tions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including inter-
ference that may cause undesirable operation. Modifications not
expressly authorized by Fujitsu Computer Systems Corporation
may invalidate the user's right to operate this equipment.
Canadian Notice
Federal Communications Commission statement
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause interference, and, (2) This device must
accept any interference, including interference that may cause
undesired operation of this device.
The device for the 5150-5250 MHz band is only for indoor usage
to reduce the potential for harmful interference to co-channel
mobile satellite systems.
The maximum antenna gain of 6 dBi permitted (for devices in the
5250-5350 MHz, 5470-5725 MHz, and 5725-5825 MHz bands) to
comply with the e.i.r.p. limit as stated in A9.2 of RSS210 .
FCC Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instruc-
tions, it may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation.
In addition, users are cautioned to take note that high power
radars are allocated as primary users (meaning they have priority)
of 5250-5350 MHz and 5650-5850 MHz and these radars could
cause interference and/or damage to LE-LAN devices.
If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
93
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
Before Using the Wireless LAN
■
This manual describes the procedures required to prop-
erly setup and configure the integrated Wireless LAN
Mini-PCI device (referred to as "WLAN device" in the
rest of the manual). Before using the WLAN device, read
this manual carefully to ensure it's correct operation.
Keep this manual in a safe place for future reference.
The WLAN device is Wi-Fi certified and operates at a
the maximum data rate of 540 Mbps (theoretical) in
IEEE802.11n (draft) mode; 54 Mbps in IEEE802.11a
or IEEE802.11g mode; and 11 Mbps in IEEE802.11b
mode.
■
■
The WLAN device supports the following encryption
methods - WEP, TKIP, CKIP, and AES encryption.
Please note throughout this document that
-- at the time of publication -- the 802.11n
standard has not yet been ratified, and is
still in draft stage.
The Wireless LAN device is compliant with the follow-
ing standards: WPA, WPA2, CCX1.0, CCX2.0,
CCX3.0, and CCX4.0.
Wireless LAN Devices Covered by this Document
This document is applicable to systems containing one
of the following two devices. Most of the procedures are
identical. Sections that differ between the two devices
have been noted in the text:
WIRELESS LAN MODES USING THIS DEVICE
Ad Hoc Mode
(See Figure A-1) "Ad Hoc Mode" refers to a wireless
network architecture where wireless network connec-
tivity between multiple computers is established without
a central wireless network device, typically known as
Access Point(s). Connectivity is accomplished using only
client devices in a peer-to-peer fashion. That is why Ad
Hoc networks are also known as peer-to-peer networks.
Ad Hoc networks are an easy and inexpensive method
for establishing network connectivity between multiple
computers. Ad Hoc mode requires that the SSID, network
authentication, and encryption key settings are identically
configured on all computers in the Ad Hoc network.
■
Intel® Wireless WiFi Link 4965AGN (802.11a/g/n)
■
Atheros® AR5006EXS (AR5BXB6) Mini-Card
Wireless network card (802.11a+b/g)
Characteristics of the WLAN Device
■
The WLAN device is a Mini-PCI card attached to the
main board of the mobile computer.
■
The WLAN device operates in license-free RF bands,
eliminating the need to procure an FCC operating
license. The WLAN operates in the 2.4GHz Industrial,
Scientific, and Medical (ISM) RF band and the lower,
middle, and upper bands of the 5GHz Unlicensed
National Information Infrastructure (UNII) bands.
Access Point (Infrastructure) Mode
(See Figure A-2) Infrastructure mode refers to a wireless
network architecture in which devices communicate
with wireless or wired network devices through an
Access Point. In infrastructure mode, wireless devices
can communicate with each other or with a wired
network. Corporate wireless networks operate in infra-
structure mode because they require access to the wired
LAN in order to access computers, devices, and services
such as file servers, printers, and databases.
■
The Atheros® AR5006EXS (AR5BXB6) Mini-Card
Wireless device is capable of three operating modes,
IEEE802.11a, IEEE802.11b and IEEE802.11g.
■
The Intel® Wireless WiFi Link 4965AGN device is
capable of four operating modes, IEEE802.11a,
IEEE802.11b, IEEE802.11g, and IEEE802.11n (draft)
Figure A-1. Ad Hoc Mode Network
94
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
How to Handle This Device
certain environments require it (i.e. hospitals, clinics,
airplanes, etc.). Fujitsu mobile computers employ three
methods with which to deactivate the WLAN device:
The WLAN device comes pre-installed in your mobile
computer. Under normal circumstances, it should not be
necessary for you to remove or re-install it. The Oper-
ating System that your mobile computer comes with has
been pre-configured to support the WLAN device.
■
Using the Wireless On/Off Switch, or,
■
In Windows Vista, using the WLAN icon in the
taskbar, or,
WIRELESS NETWORK CONSIDERATIONS
■
In Windows XP, using the Intel PROSet Software or
Atheros Client Utility software.
■
The Intel PRO/Wireless 3945ABG WLAN device sup-
ports IEEE802.11a, IEEE802.11b and IEEE802.11g.
Deactivation using the Wireless On/Off Switch
The WLAN device can be deactivated quickly and effi-
ciently by toggling the Wireless On/Off Switch to the Off
position. (Figure A-3)
■
Intel Wireless WiFi Link 4965AGN (4965AGN) device
supports IEEE802.11a, IEEE802.11b, IEEE802.11g,
and IEEE802.11n.
■
■
The WLAN device operates in the 2.4GHz ISM band
and the 5 GHz lower, middle, and upper UNII bands.
The Wireless LAN/Bluetooth On/Off
Switch will power off both the optional
wireless LAN and Bluetooth devices at the
same time. To enable or disable either one
of the devices individually, perform the
following steps:
Microwave ovens may interfere with the operation of
WLAN devices since they operate in the same 2.4GHz
frequency range as IEEE802.11b/g/n devices. Interfer-
ence by microwaves does not occur with IEEE802.11a
radio which operates in the 5 GHz RF band.
1. Slide the Wireless LAN/Bluetooth on/
off switch to On position.
■
Wireless devices that transmit in the 2.4GHz range
may interfere with operation of WLAN devices in
IEEE802.11b/g/n modes. Symptoms of interference
include reduced throughput, intermittent disconnects,
and many frame errors. It is HIGHLY recommended
that these interfering devices be powered off to ensure
proper operation of the WLAN device.
2. In the Control Panel, double-click the
Fujitsu Radio Control icon.
3. In the window that appears, click the
button associated with Bluetooth and/
or Wireless LAN Status to enable or dis-
able the individual devices.
4. Click [OK].
DEACTIVATING THE WLAN DEVICE
Deactivation of the WLAN device may be desired in
certain circumstances (to extend battery life) or where
Figure A-2. Access Point (Infrastructure) Mode Network
Wired LAN
ADSL modem,
Internet
cable modem,
or similar
Access Point*
Wireless LAN
*An optional hub for a wired
LAN may be required depending
upon the type of access point used.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
The Wireless LAN/Bluetooth On/Off switch has no
effect on systems without wireless devices.
Wireless LAN/Bluetooth
On/Off Switch
Figure A-3. Wireless LAN/Bluetooth Switch
Windows Vista: Deactivation using the icon in the
taskbar
1. Right-click the WLAN icon in the taskbar at the
bottom right of your screen.
Choose Disconnect from a network.
Windows XP: Deactivation using the Intel PROSet
Software
The WLAN device can also be deactivated in Windows
using the Intel PROSet Software. The procedure to
accomplish this:
1. Click [Start]-> [All Programs].
2. Select Intel ProSet Wireless, then click on Intel
ProSet Wireless from the menu that appears. The
Intel ProSet Wireless utility will be displayed.
3. At the bottom left corner of the window, select
Wireless Off from the dropdown list.
Windows XP: Deactivation using Atheros Client
Utility software
1. Click [Start] -> [Program Files] -> [Atheros] ->
Atheros Client Utility.
2. Choose Action and click Disable Radio.
ACTIVATING THE WLAN DEVICE
Activation of the WLAN device can be accomplished
using the same methods as the deactivation process
■
Using the Wireless On/Off Switch
■
In Windows XP, using the Intel PROSet Software or
Atheros Software.
■
In Windows Vista, by right-clicking the WLAN icon
then clicking “Connect to a network”
96
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Configuration of the WLAN Device
The optional WLAN Device can be configured to estab-
lish wireless network connectivity using one of the
following tools:
Panel -> Network and Sharing Center), and type in
relevant keywords in the Search box.
Connecting to a Network with Windows Vista
■
Intel PROSet Software - The Intel PROSet Software
After you have configured your computer, you can
connect to an active network by performing the
following steps:
allows for multiple profile setup and supports auto-
matic profile switching. Support for most industry
standard security solutions is contained in this soft-
ware.
1. Click on the WLAN icon in the system tray.
2. Select “connect to a network”.
■
Atheros Client Utility - The Atheros Client Utility soft-
ware allows for multiple profile setups and supports
automatic profile switching. Support for most indus-
try standard security solutions is contained in this
software.
Select a network from the list that appears, and click the
[Connect] button.
CONFIGURING THE WLAN USING
WINDOWS XP
There are two procedures outlines below. The first one is
for use with the Windows Vista operating system, and
the other is used with the Windows XP operating
system.
Configuring Using Intel PROSet Software
This section explains the procedure to properly
configure the WLAN device in a system using Windows
XP using the Intel PROSet Software. Pre-defined param-
eters will be required for this procedure. Please consult
with your network administrator for these parameters:
CONFIGURING THE WLAN
WITH WINDOWS VISTA
The WLAN device can be configured to establish wire-
less network connectivity using the software that is built
into Windows Vista. Support for most industry standard
security solutions is contained in this software.
Network Name - Also known as the SSID
Network Key (WEP) - Required if using static WEP
keys.
Pre-defined parameters will be required for this proce-
dure. Please consult with your network administrator
for these parameters:
Authentication Type - Open, Shared, WPA, or WPA-
PSK
Procedure
1. Click the Start button, then select Control Panel.
2. If the Control Panel is not in Classic View, select
Classic View from the left panel. Double-click the
Network and Sharing Center icon.
1. Activate the WLAN device using either the Wireless
On/Off Switch or the Intel PROSet software.
2. Click the [Start] button first and then [All Pro-
grams].
3. Select “Manage wireless networks” from the left
panel.
3. Click the icon [Intel PROSet Wireless] to execute
the Intel PROSet Wireless software.
4. Click on the [Add] button.
5. Depending upon what type of connection you
would like to make, make a selection. For an infra-
structure network, select “Manually create a net-
work profile. For ad hoc network, select “Create an
ad hoc network”.
4. Click the [Add] button. The General Settings dialog
displays.
5. Enter a profile name in the Profile Name field.
6. Enter the network SSID, in the Network Name
(SSID) field.
6. Enter the required information. It may be necessary
to consult with your network administrator for
some of the information.
7. Click Infrastructure or Ad Hoc for the operating
mode.
7. In the event you require assistance, go to the Net-
work and Sharing Center window (Start -> Control
8. Click [Advanced].
97
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
9. The Mandatory Access Point option is only used if
Infrastructure mode is selected. Use this option to
connect to a specific access point. Enter the MAC
address for the access point. Click OK to save the
setting and return to the General Settings page.
25. Click [Close] if you want to close the Intel PROSet
for Wireless window.
Configuring Using Atheros Client Utility Software
This section explains the procedure to properly
configure the WLAN device using the Atheros Client
Utility. Pre-defined parameters will be required for this
procedure. Please consult with your network adminis-
trator for these parameters:
10. Click [Next].
11. If you are using Cisco CCX, click Cisco Options to
enable Cisco CKIP data encryption on the Security
Settings page. Check the Cisco Compatible Exten-
sions Options. If you have checked the Cisco's
"Mixed-Cell" box in the Advanced Setting, this
option must also be checked.
Network Name - Also known as the SSID
Network Key (WEP) - Required if using static WEP
keys.
Authentication Type - Open, Shared, WPA, or WPA-
PSK
12. Click [OK].
13. Click Next.
Procedure
14. Select Open, Shared, WPA-Enterprise, WPA2-
Enterprise, WPA-Personal, or WPA2-Personal in
the Network Authentication options.
1. Activate the WLAN device using either the Wireless
On/Off Switch or the Atheros Client Utility
15. Select either None, WEP, CKIP (if Enable Cisco Cli-
ent eXtentions is enabled, use CKIP or WEP), or
TKIP for the data encryption.
2. Right-click on the “Atheros Client Utility” icon in
the system tray, and select “Open Atheros Client
Utility” from the menu.
16. If WEP is selected, select either 64 or 128-bit for the
Encryption Level.
3. From the Current Status page, click the Profile
Management tab.
17. Select the key index 1, 2, 3 or 4.
4. If this is your first time using this utility, highlight
the profile [Default] and Click the [Modify] button,
otherwise Click the [New] button. The General Set-
tings dialog displays.
18. Enter the WEP key if required. If your network does
not employ a 802.1x/EAP security mechanism,
please skip to step 24.
5. From the General page, enter a profile name in the
Profile Name field.
19. Click the Enable 802.1x checkbox to enable the
802.1x security option. Please contact your network
administrator if configuration of this setting is
required.
6. Enter the network SSID, in the SSID1 field. If you
wish to create a profile that can connect to up to 3
different wireless networks, SSID's can be entered
in the SSID2 and SSID3 fields as well.
20. Select the appropriate Authentication Type. Please
contact your network administrator if configura-
tion of this setting is required.
7. Click the Security tab.
21. After selecting your authentication type, enter the
user name, domain, and password of the user you
have created on the authentication server. The user
name and password do not have to be the same as
name and password of your current Windows user
login.
8. The Security tab allows for the configuration of the
Security modes listed in the table below. Please
select the radio button of the desired security
mode. If these settings are not known to you,
please consult with your network administrator for
the correct settings.
22. Click [OK] to save the settings.
Field Name
Description
WPA
Enables the use of Wi-Fi Protected
Access. Choosing WPA opens the
WPA EAP drop-down menu.
Options include TLS and PEAP. If
these settings are not known to you,
please consult with your network
administrator for the correct settings.
23. From the Intel ProSet Wireless page, click the new
profile name shown in the Profile List. Use the up
and down arrows to position the priority of the
new profile in the priority list.
24. Click the Connect button to connect to the net-
work.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
14. Click OK to close the Atheros Client Utility.
WPA-PSK
802.1x
Enables WPA-Pre-Shared Key. Click
on the Configure button to enter the
WPA Passphrase. If these settings
are not known to you, please consult
with your network administrator for
the correct settings.
CONNECTION TO THE NETWORK
This section explains connection to the network.
If there is an administrator of the network, contact the
network administrator for data settings.
Enables 802.1x security. If these
settings are not known to you,
please consult with your network
administrator for the correct settings.
Choosing this option opens the
802.1x EAP type drop-down menu.
Options include TLS, PEAP, and LEAP
Setting the network
Perform the “Setting TCP/IP” and “Confirming the
computer and work group names” operations required for
network connection.
Setting TCP/IP
Pre-Shared Key
Enables the use of pre-shared keys
that are defined on both the access
point and the station. This is where
static WEP keys are entered. Click
the Configure button to fill in the
Define Pre-Shared Keys window.
To change the setting of the IP address,
you need to be logged in from Windows
as an administrator.
1. Click the [Start] button first and then [Control
Panel].
None
No security
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
9. Click OK
10. Click the Advanced tab
11. The Advanced tab allows for the configuration of
the options detailed in the table below.
3. Double-click [Network Connections]. A list of cur-
rently installed networks will be displayed.
Field Name
Description
Power Save
Mode
Options are Maximum, Normal, or
Off
4. Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu dis-
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
Network Type
Options are AP (Infrastructure) or Ad
Hoc
802.11b
Preamble
Specifies the preamble setting in
802.11b. The default setting is Short
and Long (Access Point mode),
which allows both short and long
headers in the 802.11b frames. Set
to Long Only to override allowing
short frames.
5. Click the [General] tab if it is not already selected.
6. Click [Internet Protocol (TCP/IP] and then click
[Properties]. The [Internet Protocol (TCP/IP)
Properties] window will be displayed.
7. Set the IP address as follows:
TransmitPower
Level
Options are 100%, 50%, 25%,
12.5% or Lowest transmit power
(0mW)
■
For ad hoc connection: Select [Use the following
IP address:] and then enter data for [IP address]
and [Subnet mask]. See page 106 for IP address
setting.
Wireless Mode
Specifies the wireless mode in an
access point network.
■
For access point (infrastructure) connection: If
Wireless Mode
when Starting
Ad Hoc
Specifies 5GHz 54 Mbps, 5 GHz 108
Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz
54 Mbps to start an Ad Hoc network
if no matching network name is
found after scanning all available
modes.
your network uses DHCP, select [Obtain an IP
address automatically] and [Obtain DNS server
address automatically]. If your network uses static
IP addresses, consult with your network adminis-
trator for the correct IP address settings.
Network
8. Click the [OK] button. Processing will return to the
[Wireless Network Connection Properties] window.
12. Click OK
9. Click the [OK] button.
13. If the profile you just created does not activate
immediately, click the Profile Management tab,
highlight the desired Profile, and click Activate.
10. Close the [Network Connection] window.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
Following this operation, confirm the names of the
computer and the workgroup as follows.
This operation is not required unless the sharing func-
tion is to be used.
The folder and printer for which the sharing function
has been set will be usable from any personal computer
present on the network.
Confirming the computer and work group names
To modify the computer name and/or the
work group name, you need to be logged
in from Windows as an administrator.
To share a file and/or the connected
printer, you need to be logged in as an
administrator.
1. Click the [Start] button, then [Control Panel].
Setting the Microsoft network-sharing service
1. Click the [Start] button first and then [Control
Panel].
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
3. Double-click the [System] icon. The [System Prop-
erties] window will be displayed.
4. Click the [Computer Name] tab.
3. Double-click [Network Connections]. A list of cur-
rently installed networks will be displayed.
5. Confirm the settings of [Full computer name:] and
[Workgroup:].
4. Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu dis-
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
a. The setting of [Full computer name:] denotes the
name for identifying the computer. Any name
can be assigned for each personal computer.
5. If [File and Printer Sharing for Microsoft Net-
works] is displayed, proceed to step 6. If [File and
Printer Sharing for Microsoft Networks] is not dis-
played, skip to step 7.
To change the name, click [Change] and
then proceed in accordance with the
instruction messages displayed on the
screen.
6. Make sure that the [File and Printer Sharing for
Microsoft Networks] check box is checked, and
then click the [OK] button. Skip to “Setting file-
sharing function”.
Enter the desired name in less than 15 ASCII
character code format. Identifiability can be
enhanced by entering the model number, the
user name, and other factors.
7. Click [Install]. The [Select Network Component
Type] window will be displayed.
b. [Workgroup name] is the group name of the
network. Enter the desired name in less than 15
ASCII character code format.
8. Click [Service], then click the [Add] button. The
[Select Network Service] window will be displayed.
For ad hoc connection: Assign the same network
name to all personal computers existing on the
network.
9. Click [File and Printer Sharing for Microsoft Net-
works] and then click the [OK] button. Processing
will return to the [Wireless Network Connection
Properties] window, and [File and Printer Sharing
for Microsoft Networks] will be added to the list.
For access point (infrastructure) connection:
Assign the name of the work group to be
accessed.
10. Click the [Close] button.
6. Click the [OK] button. If a message is displayed
that requests you to restart the personal computer,
click [Yes] to restart the computer.
Setting the file-sharing function
The procedure for setting the file-sharing function
follows, with the “work” folder in drive C: as an
example.
Setting the sharing function
Set the sharing function to make file and/or printer sharing
with other network-connected personal computers valid.
1. Click the [Start] button first and then [My Com-
puter].
2. Double-click [Local disk (C:)].
100
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
3. Right-click the “work” folder (or whichever folder
you want to share), and then click [Sharing and
Security...] in the menu displayed. The [Folder
6. Click the [OK] button.
Confirming connection
After you have finished the network setup operations,
access the folder whose sharing has been set for other
personal computers. Also, confirm the status of the radio
waves in case of trouble such as a network connection
failure.
Name Properties] window will be displayed.
Setting the file-sharing function for the file
which has been used to execute Network
Setup Wizard is suggested on the screen.
For the wireless LAN, however, since
security is guaranteed by entry of the
network name (SSID) and the network
key, the steps to be taken to set the file-
sharing function easily without using
Network Setup Wizard are given below.
In the case of access point (infrastructure)
connection, enter the necessary data for
the access point before confirming
connection. Refer to the manual of the
access point for the access point setup
procedure.
4. Click [Sharing] if it isn’t already selected.
Connecting your personal computer to another
personal computer
1. Click [Start] first and then [My Computer]. The
[My Computer] window will be displayed in the left
frame.
5. Click the link stating “If you understand the secu-
rity risks, but want to share files without running
the wizard, click here”.
6. Click “Just enable file sharing” and click [OK].
2. Click [My Network Places] in the “Other Places”
list. The window [My Network Places] will be dis-
played.
7. Check the [Share this folder on the network] check
box.
3. Click [View workgroup computers] under Network
Tasks in the left frame.
To specify the corresponding folder as a
read-only folder, select the [Read only]
checkbox under the General tab.
4. Double-click the personal computer to which your
personal computer is to be connected. The folder
that was specified in “Setting the file-sharing func-
tion” on page 100 will be displayed.
8. Click the [OK] button. The folder will be set as a
sharable folder, and the display of the icon for the
“work.” folder will change.
5. Double-click the folder to be accessed.
Setting the printer-sharing function
1. Click the [Start] button first and then [Printers and
Confirming the status of the radio
1. Right-click the Intel PRO Wireless icon in the lower
right corner of the screen.
FAX]. A list of connected printers will be displayed.
2. Right-click the printer for which the sharing func-
tion is to be set, and then click [Sharing] in the
menu displayed. The property window correspond-
2. Click [Open Intel PROSet for Wireless]. The Intel
PROSet for Wireless window opens.
3. Contained within the General tab and the Details
section (accessed by pressing the [Details] button),
you will find the current operating status of the
radio. (When the radio is turned off or the com-
puter is not yet connected, some of the conditions
will not be displayed.)
ing to the selected printer will be displayed.
Setting the printer-sharing function when
Network Setup Wizard has been executed
is suggested on the screen. For the wireless
LAN, however, since security is guaranteed
by entry of the network name (SSID) and
the network key, the steps to be taken to
set the printer-sharing function without
using Network Setup Wizard are laid down
below.
■
Network Name (SSID)
Displays the Network Name (SSID) currently
used by the radio.
■
Profile Name
The current configuration profile is displayed.
3. Click the [Sharing] tab.
■
Mode
4. Click [Share this printer].
Displays the current operating mode. [Infra-
structure (AP)] or [Ad Hoc] will be displayed.
5. Enter the sharing printer name in [Share name].
101
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
■
Security
Displays the current security status of the profile
being used:
None: No encryption used.
WEP: WEP encryption algorithm used.
CKIP: WEP encryption algorithm used.
TKIP: WEP encryption algorithm used.
■
Speed
Displays the highest data rate of the associated
access point in mega-bits-per-second (Mbps)
until data transfer occurs.
802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, or
54.
802.11b: 1, 2, 5.5, or 11.
■
Band (Frequency)
Displays the current band and frequency being
used. Displays Out of Range if no band and
frequency is displayed. Displays:
802.11g (2.4 GHz) or 802.11b (2.4 GHz)
■
Channel
Displays the current transmit and receive
channel being used.
■
802.1x Protocol
Displays Enabled if the profile uses 802.1x
authentication. Default is Disabled.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Troubleshooting the WLAN
Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the
following table.
Problem
Possible Cause
Possible Solution
Incorrect network
name (SSID) or
network key
Ad hoc connection: verify that the network names (SSID’s) and network
keys (WEP) of all computers to be connected have been configured
correctly. SSID’s and WEP key values must be identical on each machine.
Unavailable
network
connection
Access Point (Infrastructure) connection: set the network name (SSID)
and network key to the same values as those of the access point.
Set the Network Authentication value identically to that of the Access
Point. Please consult your network administrator for this value, if
necessary.
For the method of setting network authentication, refer to the section of
this chapter related to the configuration tool or utility you are using.·
Weak received signal
strength and/or link
quality
Ad hoc connection: Retry connection after shortening the distance to
the destination computer or removing any obstacles for better sight.
Access Point (Infrastructure) connection: Retry connection after short-
ening the distance to the access point or removing any obstacles for
better sight.
(See Confirming connection on page 101 for more information).
The WLAN device
has been deactivated
or disabled
Check if the wireless switch is turned ON. Also verify “Disable Radio” is
not checked in “Network setting” window. (See Activating the WLAN
Device on page 96 for more information).
The computer to be
connected is turned
off
Check if the computer to be connected is turned ON.
RF interference from
Access Points or
other wireless
networks
The use of identical or overlapping RF channels can cause interference
with the operation of the WLAN device. Change the channel of your
Access Point to a channel that does not overlap with the interfering
device.
Wireless network
authentication has
failed
Re-check your Network Authentication, Encryption, and Security
settings. Incorrectly configured security settings such as an incorrectly
typed WEP key, a mis-configured LEAP username, or an incorrectly
chosen authentication method will cause the LAN device to associate
but not authenticate to the wireless network.
Incorrectly
Recheck the configuration of your network settings.
configured network
settings
For the method of checking, refer to the following page:·“Connection to
the Network” on page 99.
Incorrect IP address
configuration
This only applies to networks using static IP addresses. Please contact
your network administrator for the correct settings.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
Wireless LAN Glossary
Ad Hoc Mode
MTU (Maximum Transmission Unit)
Ad Hoc Mode refers to a wireless network architecture
where wireless network connectivity between multiple
computers is established without a central wireless
network device, typically known as Access Points.
Connectivity is accomplished using only client devices in
a peer-to-peer fashion. For details, refer to “Ad hoc
connection” on page 94.
The maximum size of data which can be transmitted at
one time in networks including the Internet. In an envi-
ronment whose maximum size of data is too large to
correctly receive data, normal communications can be
restored by setting the size of MTU to a smaller value.
Network key
Data that is used for encrypting data in data communi-
cation. The personal computer uses the same network
key both for data encryption and decryption, therefore,
it is necessary to set the same network key as the other
side of communication.
Channel
Range of narrow-band frequencies used by the WLAN
device to transmit data. IEEE802.11b/g - 11 channels, 22
MHz wide channels.
DHCP (Dynamic Host Configuration Protocol)
Network name (SSID: Security Set Identifier)
A protocol that provides a means to dynamically allocate
IP addresses to computers on a local area network.
When a wireless LAN network is configured, grouping is
performed to avoid interference or data theft. This
grouping is performed with “Network name (SSID)”. In
order to improve security, the network key is set
allowing no communication unless “Network name
(SSID)” coincides with the network key.
DNS (Domain Name System)
A data query service that provides a mechanism with
which to translate host names into Internet addresses.
IEEE802.11a
Open system authentication
Wireless LAN standard that supports a maximum data
rate of 54 Mbps. 802.11a devices operate in the 5 GHz
lower and middle UNII bands.
Null authentication method specified in the 802.11 stan-
dard that performs no authentication checks on a wire-
less client before allowing it to associate.
IEEE802.11b
PPPoE (Point to Point Protocol over Ethernet)
Wireless LAN standard that supports a maximum data
rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz
ISM band.
A method of allowing the authentication protocol
adopted in telephone line connection (PPP) to be used
over an Ethernet.
Access point
Protocol
Wireless network device used to bridge wireless and
wired network traffic.
A procedure or rule of delivering data among
computers. Ordered data communication is allowed by
making all conditions required for communication
including the method of data transmission/reception
and actions upon communication errors into proce-
dures.
IP address
The logical 32-bit host address defined by the Internet
Protocol that uniquely identifies a computer on a
network. The IP address is usually expressed in dotted
decimal notation.
Shared key authentication
LAN (Local Area Network)
802.11 network authentication method in which the AP
sends the client device a challenge text packet that the
client must then encrypt with the correct WEP key and
return to the AP. If the client has the wrong key or no
key, authentication will fail and the client will not be
allowed to associate with the AP. Shared key authentica-
tion is not considered secure, because a hacker who
detects both the clear-text challenge and the same chal-
lenge encrypted with a WEP key can decipher the WEP
key.
A LAN or Local Area Network is a computer network (or
data communications network) which is confined to a
limited geographical area.
MAC address (Media Access Control Address)
A MAC address (also called an Ethernet address or IEEE
MAC address) is the 48-bit address (typically written as
twelve hexadecimal digits, 0 through 9 and A through F,
or as six hexadecimal numbers separated by periods or
colons, e.g., 0080002012ef, 0:80:0:2:20:ef) which
uniquely identifies a computer that has an Ethernet
interface.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
SSID (Service Set Identifier)
Service Set Identifier, a 32-character unique identifier
attached to the header of packets sent over a WLAN that
acts as a password when a mobile device tries to connect
to the BSS. The SSID differentiates one WLAN from
another, so all access points and all devices attempting to
connect to a specific WLAN must use the same SSID. A
device will not be permitted to join the BSS unless it can
provide the unique SSID. Because the SSID is broadcast
in plain text, it does not supply any security to the
network.
Subnet mask
TCP-IP network is controlled by being divided into
multiple smaller networks (subnets). IP address consists
of the subnet address and the address of each computer.
Subnet mask defines how many bits of IP address
comprise the subnet address. The same value shall be set
among computers communicating with each other.
TCP/IP (Transmission Control Protocol/Internet
Protocol)
A standard protocol of the Internet.
Wi-Fi
Wi-Fi, or Wireless Fidelity, is a set of standards for wire-
less local area networks (WLAN) based on the IEEE
802.11 specifications. Certified products can use the
official Wi-Fi logo, which indicates that the product is
interoperable with any other product also showing that
logo.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
IP address information
IP addressing is much more complicated
than can be briefly explained in this
document. You are advised to consult with
your network administrator for additional
information.
If IP address is unknown, set IP address as follows:
If you have an access point (DHCP server) on the
network, set the IP address as follows:
[Obtain an IP address automatically]
A DHCP server is a server that
automatically assigns IP addresses to
computers or other devices in the network.
There is no DHCP server for the AdHoc
network.
If the IP address is already assigned to the computer in
the network, ask the network administrator to check the
IP address to be set for the computer.
If no access point is found in the network:
An IP address is expressed with four values in the range
between 1 and 255.
Set the each computer as follows: The value in paren-
theses is a subnet mask.
<Example>
Computer A: 192.168.100.2 (255.255.255.0)
Computer B: 192.168.100.3 (255.255.255.0)
Computer C: 192.168.100.4 (255.255.255.0)
:
:
Computer X: 192.168.100.254 (255.255.255.0)
106
Download from Www.Somanuals.com. All Manuals Search And Download.
W i r e l e s s L A N U s e r ’s G u i d e
Specifications
Item
Specification
Type of network
The Intel PRO/Wireless 3945ABG Network Connections WLAN
device conforms to IEEE 802.11a and 802.11b/g (Wi-Fi based)*.
The Intel PRO/Wireless4965ABGN Network Connections WLAN
device conforms to IEEE 802.11a, 802.11b/g, and 802.11n
(draft-compliant), Wi-Fi based* (Note that at the time of
publication of this document, the 802.11n standard had not yet
been ratified, and is still in draft stage.
Transfer rate
(Automatic switching) 54 Mbps maximum data rate
■
Active frequency
802.11n: 2.4 GHz or 5 GHz
■
802.11b/g: 2400~2473 MHz
■
802.11a: 4900 ~ 5850 MHz
■
Number of channels
802.11a: 8 independent channels
■
802.11b/g: 11 channels, 3 non-overlapping channels
■
802.11n:
2.4 GHz - 3 non-overlapping channels when Channel Bonding
is not used; 2 non-overlapping channels when Channel
Bonding is used.
5 GHz - 12 non-overlapping UNII channels with or without
Channel Bonding
■
Typical operating distances**
802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps
■
802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps
■
802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps
■
802.11n: Estimated double the operating distance of 802.11g
and 802.11a in their respective frequencies.
Security
Encryption Types - WEP, TKIP, AES***
WPA 1.0 compliant
Encryption Key lengths Supported: 64 bits and 128 bits
802.1x/EAP
Maximum recommended number of computers to
be connected over wireless LAN (during ad hoc
connection)
10 units or less ****
*
“Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of
wireless LAN (Wi-Fi Alliance) has been passed.
** The communication ranges shown above will increase or decrease depending on factors such as number of walls,
reflective material, or interference from external RF sources.
*** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/
104 bits after subtracting the fixed length of 24 bits.
**** Depending on practical environments, the allowable number of computers to be connected may be decreased.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
A p p e n d i x
A
Using the Bluetooth Device
The Integrated Bluetooth module (EYTF3CSFT) is an
optional device available for Fujitsu mobile computers.
Canadian Notice
To prevent radio interference to the licensed service, this
device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject
to licensing.
WHAT IS BLUETOOTH?
Bluetooth technology is designed as a short-range wire-
less link between mobile devices, such as laptop
computers, phones, printers, and cameras. Bluetooth
technology is used to create Personal Area Networks
(PANs) between devices in short-range of each other.
Warranty
Users are not authorized to modify this product. Any
modifications invalidate the warranty.
This equipment may not be modified, altered, or
changed in any way without signed written permission
from Fujitsu. Unauthorized modification will void the
equipment authorization from the FCC and Industry
Canada and the warranty.
The Wireless LAN/Bluetooth On/Off
Switch will power off both the optional
wireless LAN and Bluetooth devices at the
same time. To enable or disable either one
of the devices individually, perform the
following steps:
1. Slide the Wireless LAN/Bluetooth on/
off switch to On position.
2. In the Control Panel, double-click the
Fujitsu Radio Control icon.
3. In the window that appears, click the
button associated with Bluetooth and/
or Wireless LAN Status to enable or dis-
able the individual devices.
4. Click [OK].
WHERE TO FIND INFORMATION
ABOUT BLUETOOTH
The Bluetooth module contains a robust Help user’s
guide to assist you in learning about operation of the
Bluetooth device.
To access the Help file, click [Start] -> All Programs, and
click on Toshiba. Select Bluetooth, then select User’s
Guide.
For additional information about Bluetooth Technology,
visit the Bluetooth Website at: www.bluetooth.com.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. The
Bluetooth antenna is locateat the center of the top edge
of the LCD screen and is exempt from minimum
distance criteria due to its low power.
The transmitters in this device must not be co-located or
operated in conjunction with any other antenna or
transmitter.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Using the
Fingerprint Sensor
111
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
–
A p p e n d i x
B
112
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g t h e F i n g e r p r i n t S e n s o r
INSTALLING OMNIPASS
Fingerprint Sensor Device
If OmniPass has already been installed on your system,
skip this section and go directly to “User Enrollment” on
page 114. You can determine whether OmniPass has
already been installed by checking to see if the following
are present:
INTRODUCING THE
FINGERPRINT SENSOR DEVICE
Your system has a fingerprint sensor device just below
the pen storage location. (Figure B-1)
■
The presence of the gold key-shaped OmniPass icon in
the system tray at the bottom right of the screen.
The presence of the Softex program group in the
■
Programs group of the Start menu
System Requirements
The OmniPass application requires space on your hard
drive; it also requires specific Operating Systems (OS’s).
The minimum requirements are as follows:
■
Windows XP Home Edition or Windows XP Profes-
sional operating system
At least 35 MB available hard disk space
■
Installing the OmniPass Application
Figure B-1 Fingerprint sensor
If OmniPass is already installed on your system, go to
“User Enrollment” on page 114. Otherwise continue
with this section on software installation.
With a fingerprint sensor, you can avoid having to enter
a username and password every time you want to:
■
Log onto Windows
For installation, OmniPass requires that the
user installing OmniPass have
■
Recover from suspend mode
administrative privileges to the system. If
your current user does not have
administrative privileges, log out and then
log in with an administrator user before
proceeding with OmniPass installation.
■
Cancel a password-protected screen saver
■
Log into homepages that require a username and pass-
word
After you have “enrolled” - or registered - your finger-
print, you can simply swipe your fingertip over the
sensor for the system recognize you.
To install OmniPass on your system you must:
1. Insert the installation media for the OmniPass appli-
cation into the appropriate drive. If you are
installing from CD-ROM or DVD-ROM, you must
find and launch the OmniPass installation program
(setup.exe) from the media.
The fingerprint sensor uses Softex OmniPass which
provides password management capabilities to
Microsoft Windows operating systems. OmniPass
enables you to use a "master password" for all Windows,
applications, and on-line passwords.
2. Follow the directions provided in the OmniPass
installation program. Specify a location to which
you would like OmniPass installed. It is recom-
mended that you NOT install OmniPass in the root
directory (e.g. C:\).
OmniPass requires users to authenticate themselves
using the fingerprint sensor before granting access to the
Windows desktop. This device results in a secure
authentication system for restricting access to your
computer, applications, websites, and other password-
protected resources.
3. Once OmniPass has completed installation you will
be prompted to restart you system. Once your
system has rebooted you will be able to use
OmniPass. If you choose not to restart immediately
after installation, OmniPass will not be available for
use until the next reboot.
OmniPass presents a convenient graphical user interface,
through which you can securely manage passwords,
users, and multiple identities for each user.
GETTING STARTED
The installation program automatically places an icon
(Softex OmniPass) in the Windows Control Panel as well
as a golden key shaped icon in the taskbar.
This section guides you through the preparation of your
system for the OmniPass fingerprint recognition
application. You will be led through the OmniPass
installation process. You will also be led through the
procedure of enrolling your first user into OmniPass.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
–
A p p e n d i x
B
Verifying Information about OmniPass
to gain access. This can result in dozens of sets of creden-
tials that you have to remember.
After you have completed installing OmniPass and
restarted your system, you may wish to check the version
of OmniPass on your system.
During OmniPass user enrollment a "master password”
is created for the enrolled user. This master password
“replaces” all other passwords for sites you register with
OmniPass.
To check the version information of OmniPass:
1. From the Windows Desktop, double-click the key-
shaped OmniPass icon in the taskbar (usually
located in the lower right corner of the screen),
or,
Example: A user, John, installs OmniPass on his system
(his home computer) and enrolls an OmniPass user with
username “John_01” and password “freq14”. He then
goes to his webmail site to log onto his account. He
inputs his webmail credentials as usual (username
“John_02” and password “lifebook”), but instead of
clicking [Submit], he directs OmniPass to Remember
Password. Now whenever he returns to that site,
OmniPass will prompt him to supply access credentials.
Click the Start button, select Settings, and click
Control Panel (if you are using Windows XP you
will see the Control Panel directly in the Start menu;
click it, then click Switch to Classic View). Double-
click Softex OmniPass in the Control Panel, and the
OmniPass Control Center will appear. If it does not
appear, then the program is not properly installed,
or,
John enters his OmniPass user credentials (“John_01”
and “freq14”) in the OmniPass authentication prompt,
and he is allowed into his webmail account. He can do
this with as many websites or password protected
resources he likes, and he will gain access to all those
sites with his OmniPass user credentials (“John_01” and
“freq14”). This is assuming he is accessing those sites
with the system onto which he enrolled his OmniPass
user. OmniPass does not actually change the credentials
of the password protected resource. If John were to go to
an Internet cafe to access his webmail, he would need to
enter his original webmail credentials (“John_02” and
“lifebook”) to gain access. If he attempts his OmniPass
user credentials on a system other than where he
Click the Start button, select Programs, and from
the submenu select the Softex program group, from
that submenu click OmniPass Control Center.
2. Select the About tab at the top of the OmniPass
Control Panel. The About tab window appears with
version information about OmniPass.
Uninstalling OmniPass
For uninstallation, OmniPass requires that
the user uninstalling OmniPass have
administrative privileges to the system. If
your current user does not have
enrolled that OmniPass user, he will not gain access.
administrative privileges, log out and then
log in with an administrator user before
proceeding with OmniPass uninstallation.
The enrollment procedure assumes you
have no hardware authentication devices
or alternate storage locations that you
wish to integrate with OmniPass. If you
desire such functionality, consult the
appropriate sections of this document.
To remove the OmniPass application from your system:
1. Click Start on the Windows taskbar. Select Settings,
and then Control Panel.
2. Double-click Add/Remove Programs.
Basic Enrollment
3. Select OmniPass, and then click Change/Remove.
The Enrollment Wizard will guide you through the
process of enrolling a user. Unless you specified other-
wise, after OmniPass installation the Enrollment Wizard
will launch on Windows login. If you do not see the
Enrollment Wizard, you can bring it up by clicking Start
on the Windows taskbar; select Programs; select Softex;
click OmniPass Enrollment Wizard.
4. Follow the directions to uninstall the OmniPass
application.
5. Once OmniPass has finished uninstalling, reboot
your system when prompted.
USER ENROLLMENT
Before you can use any OmniPass features you must first
enroll a user into OmniPass.
1. Click Enroll to proceed to username and password
verification. By default, the OmniPass Enrollment
Wizard enters the credentials of the currently logged
in Windows user.
Master Password Concept
Computer resources are often protected with passwords.
Whether you are logging into your computer, accessing
your email, e-banking, paying bills online, or accessing
network resources, you often have to supply credentials
2. Enter the password you use to log in to Windows.
This will become the “master password” for this
OmniPass user. In most cases, the Domain: value
114
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g t h e F i n g e r p r i n t S e n s o r
will be your Windows computer name. In a corpo-
rate environment, or when accessing corporate
resources, the Domain: may not be your Windows
computer name. Click [Next] to continue.
3. Once OmniPass has successfully acquired the finger-
print, the Verify Fingerprint screen will automati-
cally appear. To verify your enrolled fingerprint,
swipe your fingertip over the sensor four times to
verify. Successful fingerprint verification will show a
green fingerprint in the capture window and the text
Verification Successful under the capture window.
(An unsuccessful swipe will be indicated in red.)
3. In this step OmniPass captures your fingerprint.
Refer to “Enrolling a Fingerprint” on page 115 for
additional information.
4. Next, choose how OmniPass notifies you of various
events. We recommend you keep Taskbar Tips on
Beginner mode taskbar tips and Audio Tips on at
least Prompt with system beeps only until you get
accustomed to how OmniPass operates. Click [Next]
to proceed with user enrollment. You will then see a
Congratulations screen indicating your completion
of user enrollment.
USING OMNIPASS
You are now ready to begin using OmniPass. Used regu-
larly, OmniPass will streamline your authentications.
Password Replacement
You will often use the password replacement function.
When you go to a restricted access website (e.g., your
bank, your web-based email, online auction or payment
sites), you are always prompted to enter your login
credentials. OmniPass can detect these prompts and you
can teach OmniPass your login credentials. The next
time you go to that website, you can authenticate with
your fingerprint to gain access.
5. Click [Done] to exit the OmniPass Enrollment
Wizard. You will be asked if you’d like to log in to
OmniPass with your newly enrolled user; click [Yes].
Enrolling a Fingerprint
Enrolling a fingerprint will increase the security of your
system and streamline the authentication procedure.
OmniPass Authentication Toolbar
You enroll fingerprints in the OmniPass Control Center.
With an OmniPass user logged in, double-click the
system tray OmniPass icon. Select the User Settings tab
and click Enrollment under the User Settings area. Click
Enroll Authentication Device and authenticate at the
authentication prompt to start device enrollment.
After installing OmniPass and restarting, you will notice
a dialog you have not seen before at Windows Logon.
This is the OmniPass Authentication Toolbar, and it is
displayed whenever the OmniPass authentication system
is invoked. The OmniPass authentication system may be
invoked frequently: during Windows Logon, during
OmniPass Logon, when unlocking your workstation,
when resuming from standby or hibernate, when
unlocking a password-enabled screensaver, during pass-
word replacement for remembered site or application
logins, and more. When you see this toolbar, OmniPass
is prompting you to authenticate.
1. During initial user enrollment, you will be
prompted to select the finger you wish to enroll.
Fingers that have already been enrolled will be
marked by a green check. The finger you select to
enroll at this time will be marked by a red arrow.
OmniPass will allow you re-enroll a finger. If you
choose a finger that has already been enrolled and
continue enrollment, OmniPass will enroll the
fingerprint, overwriting the old fingerprint. Select a
finger to enroll and click [Next].
The Logon Authentication window indicates what
OmniPass-restricted function you are attempting. The
icons in the lower left (fingerprint and key) show what
authentication methods are available to you. Selected
authentication methods are highlighted while unselected
methods are not. When you click the icon for an unse-
lected authentication method, the authentication
prompt associated with that method is displayed.
2. It is now time for OmniPass to capture your selected
fingerprint. It may take a several capture attempts
before OmniPass acquires your fingerprint. Should
OmniPass fail to acquire your fingerprint, or if the
capture screen times out, click [Back] to restart the
fingerprint enrollment process.
When prompted to authenticate, you must supply the
appropriate credentials: an enrolled finger for the finger-
print capture window or your master password for the
master password prompt (the key icon).
Your system has a “swipe” fingerprint sensor (See
Figure B-1). A swipe sensor is small and resembles a
skinny elongated rectangle. To capture a fingerprint,
gently swipe or pull your fingertip over the sensor
(starting at the second knuckle) towards yourself.
Swiping too fast or too slow will result in a failed
capture. The Choose Finger screen has a [Practice]
button; click it to practice capturing your finger-
print. When you are comfortable with how your
fingerprint is captured, proceed to enroll a finger.
Remembering a Password
OmniPass can remember any application, GUI, or pass-
word protected resource that has a password prompt.
Using the following procedure, you can store a set of
credentials into OmniPass. These credentials will then be
linked to your “master password” or fingerprint.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
–
A p p e n d i x
B
Go to a site that requires a login (username and pass-
word), but do not log in yet. At the site login prompt,
enter your username and password in the prompted
fields, but do not enter the site (do not hit [Enter],
[Submit], [OK], or Login). Right-click the OmniPass
system tray icon and select Remember Password from
the submenu. The Windows arrow cursor will change to
a golden key OmniPass cursor. Click this OmniPass
cursor in the login prompt area, but do not click the
[Login] or [Submit] button.
Click Finish to complete the remember password proce-
dure. The site location, the credentials to access the site,
and the OmniPass authentication settings for the site are
now stored in the OmniPass secure database. The
OmniPass authentication settings (Settings for this Pass-
word Site) can always be changed in Vault Management.
Logging in to a Remembered Site
Whether or not OmniPass prompts you to authenticate
when you return to a remembered site is determined by
Settings for this Password Site and can be changed in
Vault Management.
Associating a Friendly Name
After clicking the OmniPass key cursor near the login
prompt, OmniPass will prompt you to enter a “friendly
name” for this site. You should enter something that
reminds you of the website, the company, or the service
you are logging into. In its secure database, OmniPass
associates this friendly name with this website.
The following cases are applicable to using OmniPass to
login to: Windows, remembered websites, and all other
password protected resources.
With Master Password
Once you return to a site you have remembered with
OmniPass, you may be presented with a master pass-
word prompt. Enter your master password and you will
be allowed into the site.
Additional Settings for Remembering a Site
When OmniPass prompts you to enter a “friendly name”
you also have the opportunity to set how OmniPass
authenticates you to this site. There are three effective
settings for how OmniPass handles a remembered site.
Logging into Windows with a Fingerprint Device
When logging into Windows with a fingerprint device,
the fingerprint capture window will now appear next to
the Windows Login screen. Place your enrolled fingertip
on the sensor to authenticate. You will be simultaneously
logged into Windows and OmniPass. The capture
window will also appear if you have used Ctrl-Alt-Del to
lock a system, and the fingerprint device can be used to
log back in as stated above.
The default setting is Automatically click the “OK” or
“Submit” button for this password protected site once
the user is authenticated. With this setting, each time
you navigate to this site OmniPass will prompt you for
your master password or fingerprint authentication
device. Once you have authenticated with OmniPass,
you will automatically be logged into the site.
Less secure is the option to Automatically enter this
password protected site when it is activated. Do not
prompt for authentication. Check the upper box to get
this setting, and each time you navigate to this site
OmniPass will log you into the site without prompting
you to authenticate.
If a machine is locked and OmniPass
detects a different user logging back in
with a fingerprint, the first user will be
logged out and the second user logged in.
In Windows XP, your login options must be set either for
classic login, or for fast user switching and logon screen
to be enabled to use your fingerprint to log on to
Windows. To change this go to Control Panel, select
User Accounts and then click Change the way users log
on or off. If your Windows screensaver is password
protected, the fingerprint capture window will now
appear next to screensaver password dialog during
resume. You can authenticate to your screensaver pass-
word prompt with your enrolled finger.
This setting is more convenient in that
whenever you go to a site remembered
with this setting, you will bypass any
authentication procedure and gain instant
access to the site. But should you leave
your system unattended with your
OmniPass user logged in, anyone using
your system can browse to your password
protected sites and gain automatic access.
Password Management
If you uncheck both boxes in Settings for this Password
Site, OmniPass will prompt you for your master pass-
word or fingerprint authentication device. Once you
have authenticated with OmniPass your credentials will
be filled in to the site login prompt, but you will have to
click the website [OK], [Submit], or [Login] button to
gain access to the site.
OmniPass provides an interface that lets you manage
your passwords. To access this GUI, double-click the
OmniPass key in the system tray. Click Vault Manage-
ment; you will be prompted to authenticate. Once you
gain access to Vault Management, click Manage Pass-
words under Vault Settings. You will see the Manage
Passwords interface, with a list of friendly names.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g t h e F i n g e r p r i n t S e n s o r
You can view the credentials stored for any remembered
website by highlighting the desired resource under Pass-
word Protected Dialog and clicking Unmask Values.
Should a password be reset, or an account expire, you
can remove stored credentials from OmniPass. Highlight
the desired resource under Password Protected Dialog
and click Delete Page. You will be prompted to confirm
the password deletion.
Choosing User Identity during Login
To choose your identity during login, type your user-
name in the User Name: field. Press [Tab] and see that
the Domain: field self-populates. Click the Password:
field to bring the cursor to it, and you will see the pull-
down menu in the Identity: field. Select the identity you
wish to login as and then click OK to login.
Switch User Identity
The two check boxes in Manage Passwords govern
whether OmniPass prompts you to authenticate or
directly logs you into the remembered site.
To switch identities at any time, right-click the
OmniPass system tray icon and click Switch User Iden-
tity from the submenu. The Switch Identity dialog will
appear. Select the desired identity and then click OK.
OmniPass will overwrite an old set of credentials for a
website if you attempt to use Remember Password on an
already remembered site.
Identities and Password Management
On the Manage Passwords interface of the Vault
Management tab of the OmniPass Control Center, there
is a pull-down selection box labeled, Identity. This field
lets you choose which identity you are managing pass-
words for. When you select an identity here, only those
password protected dialogs that are associated with that
identity are shown. You can perform all the functions
explained in “Password Management” on page 116.
The exception to the above rule is the resetting of your
Windows password. If your password is reset in
Windows, then the next time you login to Windows,
OmniPass will detect the password change and prompt
you to “Update” or “Reconfirm” your password with
OmniPass. Enter your new Windows password in the
prompt(s) and click OK and your OmniPass "master
password" will still be your Windows password.
CONFIGURING OMNIPASS
This section gives an overview of both the Export/
Import function and the OmniPass Control Center.
OmniPass User Identities
Identities allow OmniPass users to have multiple
[email protected]). If OmniPass did not provide
you identities, you would be limited to remembering
one account per site.
Exporting and Importing Users
Using the OmniPass Control Center, you can export and
import users in and out of OmniPass. The export
process backs up all remembered sites, credentials, and
any enrolled fingerprints for an OmniPass user. All
OmniPass data for a user is backed up to a single
encrypted database file. During the import process, the
Windows login of the exported user is required. If the
proper credentials cannot be supplied, the user profile
will not be imported.
To create and manage identities, double-click the
OmniPass key in the system tray. Click Vault Manage-
ment; OmniPass will prompt you to authenticate. Once
you gain access to Vault Management, click Manage
Identities under Vault Settings. You can only manage
the identities of the currently logged in OmniPass user
■
To add a new identity, click New Identity or double-click
Click here to add a new identity. Name the new identity
and click [OK], then click [Apply]. You can now switch
to the new identity and start remembering passwords.
You should periodically export your user
profile and store it in a safe place. If
anything happens to your system, you
can import your OmniPass profile to a
new system and have all your remem-
bered settings and fingerprints instantly.
To delete an identity, highlight the identity you want to
delete and click [Delete Identity], then click [Apply].
■
You don't forget the Windows login
credentials when exporting. When you
examine the importation, you are
prompted for authentication. The
credentials that will allow a user profile
to be imported are the Windows login
credentials of the exported user. They
are the credentials that had to be
submitted when the user profile was
exported. You will need User Name,
Password, and Domain.
When you delete an identity, all of its
associated remembered sites and password
protected dialogs are lost.
To set the default identity, highlight the identity you
want as default and click [Set as Default]; click [Apply]
to ensure the settings are saved. If you log in to
OmniPass with a fingerprint device, you will automati-
cally be logged in to the default identity for that
OmniPass user. You can choose the identity with which
you are logging in if you login using "master password".
117
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
–
A p p e n d i x
B
■
Exporting an OmniPass User Profile
To export a user, open the OmniPass Control Center,
and click Import/Export User under Manage Users.
If you export an OmniPass-only user, you can import
that user to any computer running OmniPass, pro-
vided that a user with that name is not already
enrolled in OmniPass.
Click Exports an OmniPass user profile. OmniPass will
prompt you to authenticate. Upon successfully authenti-
cation, you must name the OmniPass user profile and
decide where to save it. An .opi file is generated, and you
should store a copy of it in a safe place.
■
If you attempt to import a user profile who has the
same name as a user already enrolled in OmniPass, the
OmniPass import function will fail.
OMNIPASS CONTROL CENTER
This section will serve to explain functions within the
OmniPass Control Center that weren’t explained earlier.
This .opi file contains all your user specific OmniPass
data, and it is both encrypted and password protected.
This user profile does NOT contain any of your
encrypted data files.
You can access the OmniPass Control Center any of
three ways:
■
Importing an OmniPass User Profile
Double-click the golden OmniPass key shaped icon in
the Windows taskbar (typically in the lower-right cor-
ner of the desktop)
You cannot import a user into OmniPass if
there already is a user with the same name
enrolled in OmniPass.
■
Click the Start button; select the Programs group;
select the Softex program group; and click the
OmniPass Control Center selection.
■
Open the Windows Control Panel (accessible via Start
To import an OmniPass user open the OmniPass
Control Center, and click Import/Export User under
Manage Users. Click Imports a new user into OmniPass
and then select OmniPass Import/Export File (*.opi)
and click Next. OmniPass will then prompt you to
browse for the file you had previously exported (.opi
file). When you select the .opi file for importation,
OmniPass will prompt you for authentication. The
credentials that will allow a user profile to be imported
are the Windows login credentials of the exported user.
They are the credentials that had to be submitted when
the user profile was exported. You will need User Name,
Password, and Domain. If you don’t remember the value
for Domain, in a PC or SOHO environment Domain
should be your computer name.
button --> Settings --> Control Panel) and double-
click the Softex OmniPass icon.
User Management
The User Management tab has two major interfaces:
Add/Remove User and Import/Export User. Import/
Export User functionality is documented in “Exporting
and Importing Users” on page 117. Add/Remove User
functionality is straightforward.
If you click Adds a new user to OmniPass you will start
the OmniPass Enrollment Wizard. The Enrollment
Wizard is documented in “User Enrollment” on
page 114.
If you click Removes a user from OmniPass, OmniPass
will prompt you to authenticate. Authenticate with the
credentials (or enrolled fingerprint) of the user you wish
to remove. OmniPass will prompt you to confirm user
removal. Click OK to complete user removal.
OmniPass will notify you if the user was successfully
imported.
Things to Know Regarding Import/Export
■
Assume you export a local Windows User profile from
Removing a user will automatically destroy
all OmniPass data associated with that
user. All identities and credentials
OmniPass. You want to import that profile to another
machine that has OmniPass. Before you can import
the profile, a Windows user with the same login cre-
dentials must be created on the machine importing the
profile.
associated with the user will be lost.
If you are sure about removing the user,
we recommend you export the user
profile.
Example: I have a Windows user with the username
“Tom” and the password “Sunshine” on my system. I
have enrolled Tom into OmniPass and remembered
passwords. I want to take all my passwords to new sys-
tem. I export Tom’s OmniPass user profile. I go to my
new system and using the Control Panel I create a user
with the username "Tom" and the password "Sun-
shine". I can now successfully import the OmniPass
user data to the new system.
User Settings
The User Settings tab has four interfaces: Audio Settings,
Taskbar Tips, and Enrollment. User settings allow users
to customize OmniPass to suit their individual prefer-
ences. Under User Settings (Audio Settings and Taskbar
Tips) you can set how OmniPass notifies the user of
118
Download from Www.Somanuals.com. All Manuals Search And Download.
U s i n g t h e F i n g e r p r i n t S e n s o r
OmniPass events (e.g., successful login, access denied,
etc.). The details of each setting under the Audio
Settings and Taskbar Tips interfaces are self-explana-
tory.
Cannot add a User with a Blank Password to OmniPass
If you experience difficulties adding a user with a
blank password to OmniPass, you may need to adjust
your local security settings. First attempt the proce-
dure explained in the Cannot add Windows user to
OmniPass section. If the difficulties persist, then try
the following procedure.
The Enrollment interface allows you to enroll finger-
prints. For the procedure to enroll and authentication
device refer to Chapter 2.3. To enroll additional finger-
prints, click Enroll Authentication Device, and authen-
ticate with OmniPass. Select the fingerprint recognition
device in the Select Authentication Device screen (it
should already be marked by a green check if you have a
finger enrolled) and click Next.
Click Start, Control Panel, Administrative Tools,
and Local Security Settings. Expand Local Policies,
expand Security Options, and double-click
Accounts: Limit local account use of blank pass-
words to console login only. This setting should be
set to Disabled.
System Settings
The OmniPass Startup Options interface can be found
in the System Settings tab. With these options you can
specify how your OmniPass Logon is tied to your
Windows Logon.
Dialog appears after OmniPass authentication during
Windows Logon
After installing OmniPass on your system, you can
choose to logon to Windows using OmniPass. You
authenticate with OmniPass (via master password, or
an enrolled security device) and OmniPass logs you
into Windows. You may, during this OmniPass
authentication, see a Login Error dialog box.
The first option, Automatically log on to OmniPass as
the current user, will do just as it says; during Windows
login, you will be logged on to OmniPass using your
Windows login credentials. If the user logging into
Windows was never enrolled into OmniPass, upon login
no one will be logged on to OmniPass. This setting is
appropriate for an office setting or any setting where
users must enter a username and password to log into a
computer. This is the default setting.
This dialog box occurs when OmniPass was unable to
log you into Windows with the credentials supplied
(username and password). This could happen for any
of the following reasons:
■
Your Windows password has changed
Your Windows account has been disabled
■
With the second option, Manually log on to OmniPass
at startup, OmniPass will prompt you to login once you
have logged on to Windows.
If you are having difficulties due to the first reason,
you will need to update OmniPass with your changed
Windows account password. Click Update Password
and you will be prompted with a dialog to reconfirm
your password.
With the third option, Do not log on to OmniPass at
startup, OmniPass will not prompt for a user to be
logged on.
You can manually log on to OmniPass by right-clicking
the OmniPass taskbar icon and clicking Log in User
from the right-click menu.
Enter the new password to your Windows user
account and click OK. If the error persists, then it is
unlikely the problem is due to your Windows user
account password changing.
TROUBLESHOOTING
You cannot use OmniPass to create Windows users. You
must first create the Windows user, and you will need
administrative privileges to do that. Once the Windows
user is created, you can add that user to OmniPass using
the same username and password
Cannot add Windows users to OmniPass
If you experience difficulties adding a Windows user
to OmniPass, you may need to adjust your local secu-
rity settings. You can do this by going to Start,
Control Panel, Administrative Tools, and Local
Security Settings. Expand Local Policies, expand
Security Options, and double-click Network Access:
Sharing and Security Model for Local Accounts. The
correct setting should be Classic - Local Users Authen-
ticate as Themselves.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
–
A p p e n d i x
B
120
Download from Www.Somanuals.com. All Manuals Search And Download.
I n d e x
Index
A
D
AC
DC in connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DC Power Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .14, 35
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Active Digitizer
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Anti-theft Lock Slot . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . . . . .35
B
Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Drivers and Application Restore CD . . . . . . . . . . . . . 67
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . .36
dead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
lithium ion battery . . . . . . . . . . . . . . . . . . . . . . . . . .43
low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61, 62
recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
warm-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
E
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
External Monitor Port . . . . . . . . . . . . . . . . . . . . . .14, 54
F
Fingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . .113
enrolling a fingerprint . . . . . . . . . . . . . . . . . . . . . .115
getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . .113
logging into a remembered site . . . . . . . . . . . . . . .116
OmniPass authentication toolbar . . . . . . . . . . . . .115
password replacement . . . . . . . . . . . . . . . . . . . . . .115
remembering a password . . . . . . . . . . . . . . . . . . .115
uninstalling OmniPass . . . . . . . . . . . . . . . . . . . . . .114
user enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . .114
using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . .115
BIOS
guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Flexible Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
eject lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Built-in Microphone . . . . . . . . . . . . . . . . . . . . . . . . . .15
Button Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22, 23
Floppy Disk, care . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
C
Function Key
CapsLock Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . .17
CD-ROM care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Changing Tablet PC Button Functions . . . . . . . . . . .24
Click Me! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Closed Cover Switch . . . . . . . . . . . . . . . . . . . . . . . . . .10
Cold-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Conventions used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
F10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
FN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Fn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
121
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
I n d e x
H
N
Hard Disk Drive
Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
NumLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
P
Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 8, 12, 54
Hibernate Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
PC Card
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 12
I
Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
calibrating the pen . . . . . . . . . . . . . . . . . . . . . . . . . .31
installing a pen tether . . . . . . . . . . . . . . . . . . . . . . . .30
replacing the tip . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
IrDA/FIR port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 53
K
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 20
cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Pen and Active Digitizer . . . . . . . . . . . . . . . . . . . . . . . .30
Pen tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
detaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
L
LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . 14, 53
LifeBook Security Application Panel
operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Power
AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Auto/Airline adapter . . . . . . . . . . . . . . . . . . . . . . . .35
failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60, 61
indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
LifeBook Security/Tablet PC Buttons . . . . . . . . . 10, 22
LifeBook T Series Tablet PC specifications
agency approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
display specifications . . . . . . . . . . . . . . . . . . . . . . . 77
environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
physical specifications . . . . . . . . . . . . . . . . . 77, 78, 79
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Power Management . . . . . . . . . . . . . . . . . . . . . . . .36, 37
Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . .39, 65
Local Area Network (LAN) . . . . . . . . . . . . . . . . . . . . . 9
M
Memory
R
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Re-Installing Individual Drivers and Applications . .67
Restarting the system . . . . . . . . . . . . . . . . . . . . . . . . . .37
Restoring Your Pre-installed Software . . . . . . . . . . . .67
RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 53
Rotation Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 45
inserting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
upgrade module . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Memory Stick
installing/removing . . . . . . . . . . . . . . . . . . . . . . . . . 50
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 8, 11, 54
microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 14
Modem (RJ-11) Jack . . . . . . . . . . . . . . . . . . . . . . . 14, 53
Modem Result Codes . . . . . . . . . . . . . . . . . . . . . . . . . 66
Modular Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Mouse, problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
S
ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
SD Card
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 45
122
Download from Www.Somanuals.com. All Manuals Search And Download.
I n d e x
Security Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Security lock slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Setting up LifeBook Security Panel . . . . . . . . . . . . . . .25
Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Smart Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Smart Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . .11, 16
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Suspend/Resume Button . . . . . . . . . . . . . . .8, 10, 36, 52
W
Warm-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Start key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Wireless LAN
Before Using the Wireless LAN . . . . . . . . . . . . . . .94
IP address information . . . . . . . . . . . . . . . . . . . . .107
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Wireless LAN Glossary . . . . . . . . . . . . . . . . . . . . .105
WLAN On/Off Switch . . . . . . . . . . . . . . . . . . . . . . .9, 12
T
Tablet Configuration . . . . . . . . . . . . . . . . . . . . . . . . . .18
Tablet Dock port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Tablet PC
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Touch Screen
clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Touchpad
clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
control adjustment . . . . . . . . . . . . . . . . . . . . . . . . . .28
double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Touchpad Pointing Device . . . . . . . . . . . . . . . . . .10, 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
mouse/keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
port replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
U
Universal Serial Bus (USB) Ports . . . . . . . . . . .8, 14, 53
USB
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
V
volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
123
Download from Www.Somanuals.com. All Manuals Search And Download.
L i f e B o o k T 4 2 0 0 S e r i e s T a b l e t P C
-
I n d e x
124
Download from Www.Somanuals.com. All Manuals Search And Download.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
126
Download from Www.Somanuals.com. All Manuals Search And Download.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
|