P3PC-E927-01EN
fi-4220C2 Image Scanner
Operator's Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
■ Regulatory Information ......................................................... v
■ Note, Liability ...................................................................... viii
■ Safety Precautions ................................................................ x
fi-4220C2 Image Scanner Operator’s Guide
i
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Items to Check Before Contacting the Agent
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A Before using the [Scan] or
fi-4220C2 Image Scanner Operator’s Guide
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing the fi-4220C2 Duplex Color Scanner product.
This document describes how to handle fi-4220C2 Duplex Color and basic operation methods. Before you
start using fi-4220C2 Duplex Color be sure to thoroughly read this manual to ensure correct use.
■Regulatory Information
FCC Declaration
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is located.
•Consult your dealer or an experienced radio/TV technician.
FCC warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
The use of a shielded interface cable is required to comply with the Class
ATTENTION
B limits of Part 15 of FCC rules.
The length of the AC cable must be 2 meters (6.6 feet) or less.
fi-4220C2 Image Scanner Operator’s Guide
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B limit for radio noise emissions from digital
apparatus set out in the Radio interference Regulations of the Canadian Department of
Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la classe B prescridtes dans le Réglesment sur le brouillage
radioélectrique dicté par le ministere des Communications du Canada.
Cet appareil numérique de la classe B est conformme à la norme NMB-003 du Canada.
Bescheinigung des Herstellers / Importeurs
Hiermit wird bescheinigt, daß der/die/das fi-4220C2
•In Übereinsstimmung mit den Bestimmungen der EN45014 (CE) funkentstört ist.
•Laut Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991: Der höchste Schalldruckpegel
beträgt 70 dB (A) oder weniger gemäß ISO/7779.
®
International ENERGY STAR Program
As an ENERGY STAR® Partner, PFU LIMITED has determined that this product
meets the ENERGY STAR® guidelines for energy efficiency.
The International ENERGY STAR® Office Equipment Program is an international
program that promotes energy saving through the penetration of energy efficient
computers and other office equipment. The program backs the development and dissemination of
products with functions that effectively reduce energy consumption. It is an open system in which
business proprietors can participate voluntarily. The targeted products are office equipment such as
computers, monitors, printers, facsimiles, copiers, scanners, and multifunction devices. Their
standards and logos (
) are uniform among participating nations.
Use in High-safety Applications
This product has been designed and manufactured on the assumption that it will be used in office,
personal, domestic, regular industrial, and general-purpose applications. It has not been designed and
manufactured for use in applications (simply called "high-safety applications" from here on) that
directly involve danger to life and health when a high degree of safety is required, for example, in the
control of nuclear reactions at nuclear power facilities, automatic flight control of aircraft, air traffic
control, operation control in mass-transport systems, medical equipment for sustaining life, and
missile firing control in weapons systems, and when provisionally the safety in question is not
ensured. The user should use this product with adopting measures for ensuring safety in such high-
safety applications. PFU LIMITED assumes no liability whatsoever for damages arising from use of
this product by the user in high-safety applications, and for any claims or compensation for damages
by the user or a third party.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Use of Mercury
Lamp(s) inside this product contain mercury and must be
recycled or disposed of according to local, state, or federal laws.
g
H
To avoid unexpected injury, read the following carefully.
Doing the following actions may result in serious personal injuries:
•Do not put the substance contained in the lamp in your mouth as it has mercury.
•Do not incinerate, crush, or shred the lamps or scanner parts.
•Do not breathe the chemical liquid contained in the scanner lamps.
Trademarks
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
ISIS, QuickScan and their respective logos are trademarks or registered trademarks of Pixel
Translations, a division of Captiva Software Corporation in the United States.
Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems Incorporated
in the United States and/or other countries.
Other product names are the trademarks or registered trademarks of the respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) and applications are indicated as follows:
®
®
Microsoft Windows 95 operating system.
Windows 95
®
®
Microsoft Windows 98 operating system.
Windows 98
®
®
Microsoft Windows Millennium Edition operating system.
Windows Me
Windows NT 4.0
®
®
Microsoft Windows NT 4.0 Server operating system,
®
®
Microsoft Windows NT 4.0 Workstation operating system.
®
®
Microsoft Windows 2000 Professional operating system.
Windows 2000
Windows XP
®
®
Microsoft Windows XP Professional operating system,
®
®
Microsoft Windows XP Home Edition operating system.
Where there is no distinction between the different versions of the above operating system, the general
term "Windows" is used.
®
®
Adobe Acrobat 6.0 Standard
Adobe Acrobat 6.0
Manufacturer
PFU LIMITED
International Sales Dept., Imaging Bussines Division, Products Group
Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan
Phone: (81-44) 540-4538
All Rights Reserved, Copyright© PFU LIMITED 2004
fi-4220C2 Image Scanner Operator’s Guide
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
■Note, Liability
BEFORE USING THIS PRODUCT, PLEASE READ THIS MANUAL CAREFULLY. IF THIS
PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY CAN OCCUR TO USERS OR
BYSTANDERS
Keep this manual in a safe place so that it can be easily referred to during use of this product.
While all efforts have been made to ensure the accuracy of all information in this manual, PFU
assumes no liability to any party for any damage caused by errors or omissions or by statements of any
kind in this manual, its updates or supplements, whether such errors are omissions or statements
resulting from negligence, accidents, or any other cause. PFU further assumes no liability arising from
the application or use of any product or system described herein; nor any liability for incidental or
consequential damages arising from the use of this manual. PFU disclaims all warranties regarding the
information contained herein, whether expressed, implied, or statutory.
Warning Indications Used In This Manual
This indication alerts operators to an operation that, if
not strictly observed, may result in severe injury or
death.
This indication alerts operators to an operation that, if
not strictly observed, may result in safety hazards to
personnel or damage to equipment.
Symbols Used In This Manual
This symbol alerts operators to particularly important information. Be
ATTENTION
sure to read this information.
This symbol alerts operators to helpful advice regarding operation.
HINT
A TRIANGLE symbol indicates that special care and attention is required.
The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users may not
perform.
The drawing inside or under the circle shows the specific action that is not
allowed.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Outline characters on a colored background show instructions users should
follow.
R
It may also include the drawing that shows the specific instruction.
Warning Label
The glass surface inside the ADF becomes hot during the operation. Be
careful not to touch the glass surface inside the ADF.
Do NOT remove from the scanner, stain or scratch the warning labels.
ATTENTION
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the interest of product
improvement. If the actual displayed screen differs from the screen examples in this manual, operate
by following the actual displayed screen while referring to the User's Manual of the scanner
application you are using. The screenshots in this manual were captured from the FUJITSU
TWAIN32 scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner
driver, QuickScan™ image capturing software and Adobe® Acrobat®.
About Maintenance
The user must not perform repairs on this scanner.
Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service
provider to have repairs done on this product.
fi-4220C2 Image Scanner Operator’s Guide
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
■Safety Precautions
Do not damage the AC cable.
A damaged AC cable may cause fire or electric shock. Do not place heavy objects on
AC cables, or pull, bend, twist, heat, damage or modify AC cables.
Do not use damaged AC cables or power plugs, or install any cables or power plugs
to loose wall sockets.
Use only specified AC cables and connector cables.
Use only specified AC cables and connector cables. Failure to use the correct cables
might cause electric shock and/or equipment failure.
Use this scanner only at the indicated power voltage.Do not
connect to multiple-power strips.
Use this scanner only at the indicated power voltage and current. Improper power
voltage and current might cause fire or electric shock. Do not connect to multiple-power
strips.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands. Doing so can cause electric shock.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug or metal fittings with a soft, dry
cloth. Accumulated dust can cause fire or electric shock.
Do not install the device in locations that has oil smoke, steam,
humidity, and dust.
Do not install the scanner in locations subject to oil smoke, steam, humidity, and dust.
Doing so might cause a fire or electric shock.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason, turn the scanner off and unplug the power
cable. Contact the store where you purchased the scanner.
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the scanner. Do not scan wet documents or
documents with paper clips or staples. Do not splash or allow the scanner to get wet.
If foreign objects (water, small metal objects, liquids, etc.) get inside the scanner,
immediately turn off the scanner and disconnect the power plug from the power outlet.
Then, contact the store where you bought the scanner or the Maintenance Service
Center. Pay particular attention to this warning in households where there are small
children.
Do not touch the inside of the scanner unless necessary.
Do not take apart or modify the scanner. The inside of the scanner contains high-
voltage components. Touching these components might cause electric shock or fire.
Do not use the scanner if there is a strange odor.
If you detect heat coming from the device or detect other problems such as smoke,
strange smells or noises, immediately turn off the scanner and disconnect its power
plug. Make sure that any smoke coming from it has stopped, before contacting the
store where you bought the scanner or an authorized FUJITSU scanner service
provider.
fi-4220C2 Image Scanner Operator’s Guide
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not install the scanner on unstable surfaces.
Make sure that the scanner is installed on a flat, level surface and that none of its
parts extend beyond the surface top, such as a desk or table. Do not install the
scanner on unstable surfaces. Install the scanner on a level surface that is free of
vibration to prevent it from falling.
Install the scanner on a strong surface that will support the weight of the scanner and
other devices.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the ventilation ports generates heat inside
of scanner, which may result in fire or scanner failure.
Do not place heavy objects or stand on top of the scanner.
Do not place heavy objects on the scanner or use the scanner's surface top to
perform other work. Improper installation might cause injuries and equipment failure.
Firmly insert the power plug.
Firmly insert the power plug as far it can go into the power outlet.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism during scanning since this may cause
injuries.
Do not use the scanner immediately after moving it from a cold
place into a warm room.
Do not use the device immediately after moving it from a cold place into a warm room.
Condensation may occur, which might lead to scanning errors. Let the device dry
about one or two hours before you use it.
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Before moving the scanner, disconnect the power plug from the
power outlet.
Do not move the scanner with the power and interface cables connected as this can
damage the cables, which can later cause fire, electric shock as well as injury.
Before moving the scanner, be sure to disconnect the power plug from the power
outlet, and all other data cables. Make sure that the floor is free of any obstructions.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of electronic
noise. Also, protect the scanner against any static electricity, which can cause the
scanner to malfunction.
Do not use aerosol sprays near the scanner.
Do not use aerosol sprays to clean the scanner. Aerosol sprays can blow dirt and dust
inside the scanner, resulting in scanner failure or malfunction.
Disconnect the power plug from the power outlet when the
scanner is not used for a long period of time.
When the scanner is not going to be used for a long period of time, be sure to
disconnect the power plug from the power outlet.
Do not install the scanner in direct sunlight.
Do not install the scanner under direct sunlight or near heating apparatus. Doing so
might cause excessive heat to build up inside the scanner, which can cause scanner
trouble or even fire. Install the scanner in a well-ventilated location.
Before moving the scanner, make sure the shipping lock is
locked.
When moving the scanner, be sure to lock the shipping lock in order to prevent
damages to the scanner.
fi-4220C2 Image Scanner Operator’s Guide
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
BASIC SCANNER OPERATIONS
1
This chapter describes basic scanner operations.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows
XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in
this chapter will differ slightly.
1.5 How to Use the Scanner Driver....................................................................... 10
fi-4220C2 Image Scanner Operator’s Guide
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Turning the Scanner ON
This section describes how to turn the scanner ON.
The following shows the procedure for turning the scanner ON.
1. Press the power button on the operator panel.
The scanner is turned ON, and the green LED on the operator panel lights.
Also, while the scanner is being initialized, the indication of the Function Number display
changes as follows:
"8" -> "P" -> "0" -> "1"
The indication "1" means that the operator panel is in the ready status.
Power button
To turn the scanner OFF, hold the power button down for at least two
HINT
seconds.
■ Power Save Mode
The Power Save mode keeps the scanner in a low-powered state after it has been turned ON.
If no operation is performed on the scanner for 15 minutes, the scanner automatically switches to
the Power Save mode.
In the Power Save mode, the indication of the Function Number display on the operator panel goes
out, but the green LED stays lit.
To return from the Power Save mode, perform one of the following:
• Load the document on the ADF paper chute.
• Press any button on the operator panel.
The scanner will be turned OFF when pressing down the power button for at least two
seconds.
• Execute a command from the scanner driver.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Loading Documents on the ADF for Scanning
1.2 Loading Documents on the ADF for Scanning
1. Align the edges of the documents.
1) Confirm that all the documents have the same width.
2) Check the number of sheets in the document stack.
1
The standard number of sheets that can be loaded on the scanner is as follows:
• A4-size paper or smaller that makes a document stack of 5mm or less
• Maximum 50 sheet at A4, 20 lb, or 80 g/m2
2. Fan the documents as follows:
1) Lightly grip both ends of the document with both hands, and bend the document as fol-
lows.
5mm
2) Firmly holding the document with both hands, bend back the document as follows so that
the bent section rises up in the middle of the document as follows.
3) Repeat steps 1) to 2) a few times.
4) Rotate the document 90 degrees, and fan again.
3. Align the top of the documents.
fi-4220C2 Image Scanner Operator’s Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Load the document on the ADF paper chute.
Set the documents face-down in the ADF paper chute (so that the side to be scanned faces
towards the ADF paper chute).
Load the document facing
the ADF paper chute.(face down)
Before loading A4-size documents, pull out the ADF paper chute
HINT
extension.
Extension
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Loading Documents on the ADF for Scanning
In case of operating with Windows XP OS:
ATTENTION
When the document is set on the ADF paper chute the following win-
dow may appear on the screen.
1
In this window, you can select the application program which will per-
form the scanning.
By selecting the application program from the "Select the program to
launch for this action" menu and clicking the [OK] button, the selected
program will be iniciated.
For further information, please refer to "APPENDIX A Before using the
5. Adjust the side guides to the width of the documents.
Move the side guides so that they touch both sides of the documents.
If there is any space between the side guides and the edges of documents, the scanned image
may be skewed.
Side guide
fi-4220C2 Image Scanner Operator’s Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The stacker prevents document sheets from dropping after they are
scanned.
HINT
Lift the paper stop and swing it forward by inserting your fingertips
into the indentaitons on the scanner as shown in the figure below.
Indentation
6. Start up the scanner application, and scan the document.
For details on how to scan documents using the ScandAll 21 application, refer to "1.4 Scan-
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Loading Documents on the Flatbed for Scanning
1.3 Loading Documents on the Flatbed for Scanning
1. Lift up the document cover.
1
2. Load the document on the document bed with the scanning face down and the top left
corner aligned with the reference point.
Align the top left
corner of the
document with the
reference point.
ABC
Reference point
3. Gently close the document cover.
4. Start up the scanner application, and scan the document.
For details on how to scan documents using the ScandAll 21 application, see "1.4 Scanning
fi-4220C2 Image Scanner Operator’s Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Scanning Documents
1. Load the document on the scanner's ADF paper chute or Flatbed.
For details on how to load documents, see "1.2 Loading Documents on the ADF for Scan-
2. Start up ScandAll 21.
Select [Start] - [Program] - [Scanner Utility for Microsoft Windows] - [ScandAll 21].
This starts up ScandAll 21.
3. Select the scanner to be used.
Select [Select Source] from the [Scan] menu.
⇒ The [Select Source] dialog box appears.
Select "FUJITSU fi-4220C2dj" (for Windows 95 and WindowsNT 4.0, select "FUJITSU
TWAIN 32") and click the [Select] button.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Scanning Documents
4. Click the [Scan To View] button on the tool bar.
1
⇒ The [TWAIN Driver] dialog box (screen for setting the scan conditions) appears.
5. Set the scan resolution, paper size and other scan conditions, and click the [Scan]
button.
For details on settings in the [TWAIN Driver] dialog box, refer to "1.5 How to Use the Scan-
⇒ The document is scanned, and an image of the scanned document appears on the
ScandAll 21 screen.
For details on scanning other types of documents, refer to "Chapter 2 SCANNING VARIOUS
For details on ScandAll 21 functions and operations, refer to ScandAll 21 Help.
fi-4220C2 Image Scanner Operator’s Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
■ FUJITSU TWAIN32 Scanner Driver
FUJITSU TWAIN32 Scanner Driver is designed for scanning documents with FUJITSU image
scanner fi series by using application software that complies with the TWAIN standard.
The following describes the procedure with examples of ScandAll 21 for ordinary scanning by
using this driver software.
1. Procedure for Basic Scanning Operation
1) Startup the application.
From the [Start] menu, select [Programs]-[Scanner Utility for Microsoft Window] and
click [ScandAll 21].
2) Select your scanner on the window below.
Select [Select Source] from the [Scan] menu.
3) Select the scanner to use, then click the [Select] button.
Select
• [FUJITSU fi-4220C2dj] for FUJITSU TWAIN32 V9
or
• [FUJITSU TWAIN32] for FUJITSU TWAIN32 V8
then click the [Select] button.
4) Load the documents on the scanner.
For details on loading documents, refer to "1.2 Loading Documents on the ADF for
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
5) Open the TWAIN Driver window.
Select [Scan To View] from the [Scan] menu.
ScandAll 21 provide scanning methods as follows:
• [To View...]: Displays scanned images on the window.
HINT
• [To File...:]: Saves scanned images as files (*.BMP, *.TIF, *.JPG).
• [To FTP...:]: Transfers scanned images to a FTP server.
• [To Adobe PDF...:]: Saves scanned images as PDF files.
(*Adobe Acrobat must be installed beforehand.)
• [To Microsoft SharePoint Portal Server...]: Transfers scanned images to
Microsoft Share Point Portal Server.
1
• [To Mail...]: Launches mailer software and attaches scanned images to e-
mail.
For details, refer to "ScandAll 21 Help".
6) Configure settings for scanning and click the [Scan] button.
For details about the settings on this window, refer to "Setting Window for FUJITSU
⇒ The images of scanned documents are displayed on the [ScandAll 21] window.
fi-4220C2 Image Scanner Operator’s Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the settings of the application software, images may not be displayed.
For details, refer to the documentation or Help file of your application.
e.x.) When you select [To File...] from the [Scan] menu of ScandAll 21, images of
scanned documents are not displayed on the window.
7) Save the scanned images.
Select [Save As...] from the [File] menu to save the scanned images.
If you wish to start another scanning, return to procedure 4.
8) End the application.
Select [Exit] from the [File] menu.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
2. Setting Window for FUJITSU TWAIN32 Scanner Driver
1
You can configure settings for the FUJITSU TWAIN32 Scanner Driver on this window.
The following describes the main setting items.
• For details on each functions, refer to "FUJITSU TWAIN32 Scanner Driver Help"
(appears by pressing [Help] or [F1] button).
• Depending on the type of your scanner, available setting items or range of setting
values vary.
Resolution
Specifies the resolution of scanning.
It can be specified by selecting a default value from the list or customizing (specify any
resolution in 1 dpi unit).
By marking the [Predefine] checkbox, you can select one from three predefined set-
tings as [Normal], [Fine], [Super Fine] to scan documents instead of setting details by
yourself.
Otherwise, you can change the details of the predefined settings on the [Resolution Set-
ting] window, which appears when you click on the [...] button.
Scan Type
Specifies the feeding method, the side(s) to be scanned (Front Side, Back Side, Duplex,
flatbed ) or details of Long page (the size of documents longer than A4).
Paper Size
Select the size of documents to be scanned from this list.
Windows for customizing the paper size will appear when you click on [...] besides the
list. You can save any document size as a customized setting (up to three) or for chang-
ing the order of the paper size in the list.
fi-4220C2 Image Scanner Operator’s Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Mode
Specifies the image type for the scanned documents.
Black & White
Halftone
Documents are scanned in binary (black and white).
Documents are scanned through halftone processing
in black and white.
Grayscale
Documents are scanned in gradations from black to
white. For this mode you can select 256 gradations or
4 bit (16 gardations).
Color
Documents are scanned in color. For this mode, you
can select 24 bit Color, 256 Color or 8 Color.
[Scan] button
Starts scanning documents with the current settings.
[Preview] button
Documents are scanned preliminarily before the actual scanning.
You can confirm the image of the documents in the preview window.
[Close] button
Saves the current settings and closes this window.
[Reset] button
Used to undo changes of settings.
[Help] button
Opens the "FUJITSU TWAIN32 Scanner Driver Help" window. The window also
opens by pushing the [F1] key.
[About...] button
Opens an information window about the FUJITSU TWAIN32 Scanner Driver's ver-
sion.
[Option...] button
You can set up the details of optional functions on the window below.
[Rotation] tab
Select this tab when setting image rotation, detection of document size, etc.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
[Job/Cache] tab
Select this tab when setting cache mode, multi feed detection, blank page skipping,
etc.
[Generic] tab
Select this tab to change the unit displayed on the Setting Window for the FUJITSU
TWAIN32 Scanner Driver. (Millimeters, Inches, and Pixels are available)
1
[Startup] tab
Select this tab for setting the Scanner Operation Panel.
[Filter] tab
Select this tab for setting the image processing filter(s).
Page Edge Filler: Fills up the margins of the scanned documents with a selected
color.
Digital Endoser: A character string, such as the alphabet and numbers, can be added
in the scanned document.
[Compression] tab
Select this tab for setting the compression rate of JPEG Transfer.
[Advance...] button
Click this button for settings of the advanced image processing.
You can set Edge Extract, Gamma Pattern, White Level Follower, Dropout Color,
Reverse, etc.
[Config...] button
Click this button for configuring the Setting Files.
You can save the changed settings as a Setting File. From next scanning, the settings
are quickly changed by using these Setting Files.
For details of each function, refer to the "FUJITSU TWAIN32 Scsnner Driver Help".
fi-4220C2 Image Scanner Operator’s Guide
15
Download from Www.Somanuals.com. All Manuals Search And Download.
■ FUJITSU ISIS Scanner Driver
FUJITSU ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi
series by using application software that complies with The ISIS standard.
The following describes the procedure with examples of QuickScan for ordinary scanning by using
this driver software.
The procedure may vary depending on your application. If you use an application other than
QuickScan, please refer to its Guide or Help for further information.
1. Procedure for Basic Scanning Operation
1) Startup the application.
From the [Start] menu, select [Programs] - [QuickScan] and click [QuickScan].
2) Select your scanner on the window below.
Select [Scan] - [Select Scanner] on the menu bar.
3) Select fi-4220C2, then click the [OK] button.
4) Select [Scan] - [New Batch] on the menu bar.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
5) Select the profile for scanning.
1
•
•
•
When creating a new profile
Select one from already existing profiles and click [Add Profile...] button.
⇒ A new profile will be created based on the profile you select.
When changing the settings of already existing profiles
Select one from already existing profiles and click [Edit Profile...] button.
⇒ The settings of the selected profile can be changed.
When using an existing profile
Select one from an already existing profiles.
⇒ Scanning will be started according to the settings of the selected profile.
Go to procedure 9.
6) Open the window of ISIS Driver.
Select the [Scan] tab and click the [Scanner Settings] on the [Profile Editor] window.
⇒ The configuration window of ISIS driver appears.
fi-4220C2 Image Scanner Operator’s Guide
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Configure settings for scanning and click the [OK] button.
For details on this dialog box, refer to "Configuration Window of FUJITSU ISIS Scan-
8) The [Profile Editor] window appears. Click the [OK] button to return to [New batch]
dialog.
9) Load the documents on the scanner.
10) Click the [Scan] button.
⇒ Scanned images are displayed on the window.
Refer to the "QuickScan Overview" or the "QuickScan Help" for further information
on functions and operations of QuickScan. After the installation of QuickScan, it is reg-
istered in the [Start] menu.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
2. Configuration Window of FUJITSU ISIS Scanner Driver
1
Image Mode
Select a color mode suitable for the purpose from the menu.
Black & White
Scans data in binary (black and white). Distinguishes
black from white according to the fixed threshold.
This scanning mode is suitable for scanning line
drawings and text documents.
16-level Grayscale Scans data by 14 shades of gray plus black and white.
This mode uses 4 bits per pixel.
256-level Grayscale Scans data by 254 shades of gray plus black and
white. This mode uses 8 bits per pixel. This mode is
switable for scanning monochrome photographs.
24-bit Color
Scans data as full-colored image using 24 bits per
pixel. This mode is suitable for scanning color photo-
graphs.
Image Processing
Binary processing is applied to the scanned images
This mode is available only when Image Processing
Software Option (separately sold) is installed. Please
refer to the "User’s Guide of Image Processing Soft-
ware Option" for details.
Resolution
Specifies the number of pixels (dots) per inch.
Select a fixed resolution from the list or enter any value (from 50 to 600) manually.
A higher resolution produces finer image, but requires much more memory.
fi-4220C2 Image Scanner Operator’s Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Halftone
Select the halftone pattern for halftone scanning. This setting is available when "Black
& White" is selected in the "Image Mode".
Dither Pattern 0
Dither Pattern 1
Dither Pattern 2
Dither Pattern 3
Error Diffusion
This setting is suitable for scanning dark photo-
graphs.
This setting is suitable for scanning dark-colored
documents containing both text and photographs.
This setting is suitable for scanning light photo-
graphs.
This setting is suitable for scanning light-colored
documents containing both text and photographs.
This function minimizes differences of color levels
due to subtractive color process by diffusing the dif-
ference to the adjacent pixels. This mode is suitable
for scanning images of photographs, etc.
Executes processing with the dithered download pat-
tern specified in the dithered download file.
Download
Brightness
Sets the brightness of the entire image. Specify the brightness as a number within the
range of 1 (dark) to 255 (bright). To brighten the entire image, increase the value of the
setting. To darken the entire image, decrease the value.
Contrast
Sets the contrast between light and shadow of the scanned image. Specify the contrast
as a number within the range of 1 (low [soft]) to 255 (high [sharp]). Increasing this
value makes the contrast sharper.
Scan Type
Selects the scanning method.
Automatic
Detects the document loaded onto the scanner and
determines automatically whether to scan from the
ADF, or from the Flatbed.
Flatbed
Scans the document placed on the flatbed.
Scans only the front sides of documents.
ADF (Front Side)
ADF (Back Side)
ADF (Duplex)
Scans only back sides of documents.
Scans both front and the back sides of documents.
When this option is selected, the both sides of docu-
ments are scanned simultaneously. This option can be
used only for the models that support duplex scanning.
Paper Size
Selects a paper size according to the size of the document to be scanned. Select a stan-
dard paper size from the list.
Paper Layout
Specifies orientation of the documents as portrait or landscape.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
Automatic Size and Skew detection
This option will adjust the output to the detected page size, and it will detect and auto-
matically correct the skew of the document.
With [Priority] slider control, you can change accuracy of Automatic Page Size Detec-
tion. Move the slider to the right when improving the detection accuracy.
[Area...] button
Opens the Scan Area dialog box.
1
Specify scan area for the document size.
The size can be set by dragging the frame with mouse.
Otherwise, enter any value for the setting.
[JPEG...] button
Opens the JPEG Settings dialog box. Used for setting the compression rate of JPEG
transfer.
[About...] button
This button displays the version information.
fi-4220C2 Image Scanner Operator’s Guide
21
Download from Www.Somanuals.com. All Manuals Search And Download.
[More...] button
Opens [More Settings] window. Used for setting advanced features.
End of Page Detection
Scans the edge (bottom) of the documents and outputs data adjusted to the document
length. When any page shorter than specified "Paper Size" is included, the output size
is adjusted to the detected short size.
Overscan
This function makes the scanned images larger than the original documents by adding
margins.
Backing
With this function, the outside of document paper becomes black / white by selecting
[black] / [white] background.
Gamma
Specifies Gamma correction. Correction patterns are: "Normal", "Soft", "Sharp", "Cus-
tom", or "Download".
DTC Variance
This option specifies the value for adjusting the variance based on the brightness of the
image.
Edge Processing
This option specifies the sharpness of contour extraction.
Low, Mid, High
Emphasizes contour of images. Available settings
are: Low, Mid, High
Smoothing
Smoothes jaggy images.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
Dropout Color
This option excludes selected color (the three primary colors of light i.e. green, red,
blue) from scanned images. For example, if the document contains black text in a red
frame and when the red color is selected, the scanner reads only the text and eliminate
(drop out) the red frame.
If you do not wish to have any colors dropped out select "None".
Reverse
1
Colors of scanned images are reversed.
Multi feed Detection
Detects Multi feeds (phenomena that two or more sheets are accidentally fed). You can
set conditions for detecting Multi feeds so that the scanner should stop and display
error messages. Multi feeds are scanned by the differences in document lengths or
thicknesses.
fi-4220C2 Image Scanner Operator’s Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
SCANNING VARIOUS TYPES OF
DOCUMENTS
2
This chapter describes how to scan various types of documents.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows
XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in
this chapter will differ slightly.
2.1 Scanning Double Sided Docments................................................................. 26
2.10 Correcting skewed documents..................................................................... 46
fi-4220C2 Image Scanner Operator’s Guide
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Scanning Double Sided Docments
The following shows the procedure for reading the double sided documents.
1. Load the document on the ADF paper chute.
Load the document facing
the ADF paper chute.(face down)
2. Adjust the side guides to the width of the documents.
Side guide
3. Start up ScandAll 21.
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] -
[ScandAll 21]. This starts up ScandAll 21.
4. Select fi-4220C2.
5. Click [Scan To View] on the tool bar. The [TWAIN Driver] dialogbox appears.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Scanning Double Sided Docments
6. Select [ADF (Duplex)] from [Scan Type].
2
7. Click the [Scan] button.
For [TWAIN Driver] dialog box setting, refer to "1.5 How to Use the Scanner Driver" (page.
⇒ The document is scanned, and an image of the scanned document appears on the
ScandAll 21 screen. For ScandAll functions and operation, refer to [ScandAll 21 Help].
fi-4220C2 Image Scanner Operator’s Guide
27
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Scanning Books
4. Issue the scan command on the host system.
For details on scanning commands, refer to "1.4 Scanning Documents" (page. 8).
Do not move the document during scanning.
ATTENTION
5. When scanning ends, re-attach and gently close the document cover.
2
fi-4220C2 Image Scanner Operator’s Guide
29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Scanning Large Documents with Flatbed
CAUTION
Never look directly the light source during scanning.
1. Remove the document cover as shown in the figure below.
2. Load the document on the document bed face down.
3. Issue the scan command on the host system.
For details on scanning commands, refer to "1.4 Scanning Documents" (page. 8).
Do not move the document during scanning.
ATTENTION
4. When scanning ends, re-attach and gently close the document cover.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Scanning Documents longer than A4 size
2.4 Scanning Documents longer than A4 size
1. Load the documents on the ADF paper chute.
For details on loading documents, refer to "1.2 Loading Documents on the ADF for Scan-
2
Load the document facing
the ADF paper chute.(face down)
2. Adjust the side guides to the document width.
Side guide
3. Start up ScandAll 21.
For starting up ScandAll 21, select [Programs] - [Scanner Utility for Microsoft Windows] -
[ScandAll 21] from [Start].
4. Select fi-4220C2.
5. Click [Scan To View] on the tool bar.
⇒ The [TWAIN Driver] dialogbox appears.
fi-4220C2 Image Scanner Operator’s Guide
31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Select [Long page (Front Side)] or [Long page (Duplex)] from [Scan Type].
7. Specify the length of documents.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Scanning Documents longer than A4 size
8. Click the [Scan] button.
For settings in the [TWAIN Driver] dialogbox, refer to "1.5 How to Use the Scanner
2
⇒ Images of scanned documents are displayed on the window of ScandAll 21.
For details on functions and operations of ScandAll 21, refer to "ScandAll 21 Help".
fi-4220C2 Image Scanner Operator’s Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Scanning Different-width Documents
When you scan a batch of documents with different widths by using the ADF, you may get skewed
images from smaller sized documents.
Be sure to scan only documents of the same width together.
The following shows the procedure for scanning a batch of mixed size documents.
1. Sort out the batch into stacks of the same width.
2. Adjust the side guides to the width of each document stack.
3. Scan the batches of the same widths sparately one by one.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Saving Scanned Images in PDF Format
2.6 Saving Scanned Images in PDF Format
To save scanned images in PDF format, Adobe Acrobat 6.0 or later must be installed on your PC.
Adobe Acrobat 6.0 can be installed from the provided Adobe Acrobat CD-ROM.
There are 2 ways for saving scanned images in PDF format.
1. Using ScandAll 21
This method is recommended for color or grayscale scanning and when smaller PDF
file size is required.
The benefits are:
2
• Reduced PDF data size
• Simplified method for creating PDF files with no troublesome operations
2. Using Adobe Acrobat 6.0
This method is recommended for faster creation of PDF files and for black and white scan-
ning.
The benefits are:
• Quick creation of PDF files with the original scan resolution
• Flexibile creation of PDF files by changing the PDF compression rates
Grayscale or color scanning creates larger file sizes than black and white scanning.
If the file size is very large, you can reduce the file size by configuring the properties of
Acrobat Distiller before saving scanned images.
For details, please refer to the hints on page 40.
■ Using ScandAll 21
1. Load the documents on the ADF paper chute or the flat bed.
2. Start up ScandAll 21.
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] -
[ScandAll 21]. This starts up ScandAll 21.
3. From the menu bar select [Scan] and then [To Adobe PDF] from the pull down menu.
⇒ [TWAIN Driver] dialog box is displayed.
fi-4220C2 Image Scanner Operator’s Guide
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Select the scan resolution, document size and other scan conditions, and then click
the [Scan] botton.
5. To end scanning, click the [Close] button.
6. Enter the file name and select the destination to save the scanned image.
For details, refer to ScandAll 21 Help.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Saving Scanned Images in PDF Format
■ Using Adobe Acrobat 6.0
1. Load the documents on the ADF paper chute or flat bed.
2. Start up Adobe Acrobat 6.0.
Select [Program] - [Adobe Acrobat 6.0] from the [Start] menu. This starts up Adobe Acrobat
6.0.
3. From the [File] menu select [Create PDF] - [From Scanner].
2
⇒ [Acrobat Scan Plug-in] dialog box is displayed.
4. Select [FUJITSU fi-4220C2dj] ([FUJITSU TWAIN 32] for WindowsNT 4.0) at [Device]
and click [Scan] button.
⇒ [TWAIN driver] dialog box is displayed.
fi-4220C2 Image Scanner Operator’s Guide
37
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select the scan resolution, document size and other scan conditions, and click the
[Scan] button.
6. To end scanning, click the [Done] button.
⇒ The scanned image is displayed.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Saving Scanned Images in PDF Format
7. Select [Save as...] or [Save] from [File] menu to save the scanned image.
2
For the details on Adobe Acrobat 6.0 operations, refer to the Adobe Acrobat 6.0 manual and
Help.
fi-4220C2 Image Scanner Operator’s Guide
39
Download from Www.Somanuals.com. All Manuals Search And Download.
If you save scanned documents using this procedure, the file size
may increase. For reducing the file size, please follow the procedure
below. (It may take more time than usual)
HINT
1. Select [File] - |[Print...].
2. On the following dialog specify [Adobe PDF] for [Name].
3. Click the [Properties] button.
4. Click the [Adobe PDF settings] tab.
5. Select one from [Default Settings].
The following shows an example of [Standard].
.
6. Click [OK] button.
7. Enter a file name and click the [Save] button on the [Save PDF
File As] dialogbox.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Excluding a Color in the Image (dropout color)
2.7 Excluding a Color in the Image (dropout color)
A selected color (primary colors: red, green or blue) can be removed (dropped out) from the
scanned image data.
For example, if the document contains black text in a green frame, you can set the scanner to read
only the text and eliminate (drop out) the green frame.
To set the scanner to drop out a color, change the settings in the [TWAIN Driver] dialogbox before
scanning.
1. Click the [Advance...] button in the [TWAIN Driver] dialog box.
2
⇒ The [Advance] dialog box appears.
2. Select the color to be drop out from [Dropout Color] under [More].
For example, if the document contains black text in green frame, select [Green] so that the
scanner only reads the text and eliminates the frames.
If you do not wish to have any colors dropped out select "None".
3. Click the [OK] button.
The [TWAIN Driver] dialog box will be redisplayed. Continue scanning from this dialog
box.
fi-4220C2 Image Scanner Operator’s Guide
41
Download from Www.Somanuals.com. All Manuals Search And Download.
2.8 Skipping blank pages
Change settings in the [TWAIN Driver] dialog box for skipping blank pages at scanning docu-
ments.
1. Click [Option] button in the [TWAIN Driver] dialog box.
⇒The [Option] dialog box appears.
2. Click the [Job/Cache] tab.
3. Check the [Blank Page Skip] box.
If an item other than “Ram cache” or “Use Both Memory” has been selected in the [Cache
Mode:] and this check box is marked, it will change to “Ram cache”.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
2.8 Skipping blank pages
4. With the slider control under [Blank Page Skip], specify the Blank Page Skip degree.
<In Binary/Halftone mode>
For white pages, use the [Black Dots Ratio] slider bar to set the skip condition. For black
pages, use the [White Dots Ratio] scroll bar to set the skip condition.
The value displayed to the right of the scroll bar displays the noise ratio(*1). If a scanned
document is below this value, it is recognized as a blank page. The setting range is OFF(- -)
and 0.2% to 3.0% (in increments of 0.2%).
2
*1: Ratio of black dots included in the scanning area. (for white pages)
<In Color/Grayscale mode>
Use the slider bar to set the skip condition in five stages from 1 to 5. To make the blank
pages easy to skip, increase the value of the setting.
fi-4220C2 Image Scanner Operator’s Guide
43
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Detecting Multi feeds
"Multi feed" is a feeding error that occurs when two or more sheets in the ADF paper chute are fed
simultaneously into the scanner.
You can set the scanner to detect multi feed, stop scanner operation, and display an error message.
To set the scanner to detect multi feed, change the settings in the [TWAIN Driver] dialog box.
1. Click the [Option...] button in the [TWAIN Driver] dialog box.
⇒ The [Option] dialog box appears.
2. Click the [Job/Cache] tab.
3. Select the detection conditions from "Multi Feed Detection" under "ADF Option".
44
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Detecting Multi feeds
The following detection conditions are provided:
None
: Multi feed detection is not performed.
Check thickness
: The scanner monitors the thickness of documents. It detects a multi
feed by differences in document thickness when two or more docu-
ment sheets are fed overlapping.
Check length
: The scanner monitors the length of documents. It detects a multi
feed by changes in the document length when two or more document
sheets are fed overlapping.
Check thickness and length:
The scanner monitors both document thickness and length to detect
multi feed.
2
Furthermore, see "6.5 Multi feed Detection Conditions" (page. 99) for detailed information
about the document for multi feed detection.
4. Click the [OK] button.
The display returns to the [TWAIN Driver] dialog box. Continue scanning from this dialog
box.
fi-4220C2 Image Scanner Operator’s Guide
45
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 Correcting skewed documents
You can set the scanner so that skew of documents are detected and corrected automatically when
skewed documents are fed into the ADF. Change the setting in the [TWAIN Driver] dialog box to
enable this function. The following shows the procedure for changing the setting in the dialog box:
1. Click [Option] button in the [TWAIN Driver] dialog box.
⇒ The [Option] dialog box appears.
2. Click the [Rotation] tab.
3. Select the [Automatic page size detection ] from the [Automatic Size and Skew Detec-
tion] menu.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 Correcting skewed documents
4. Click the [OK] button. The display returns to [TWAIN Driver] dialog box. Perform the
scanning operation on the dialog box.
With [Priority] slider control, you can change accuracy of Automatic
HINT
Page Size Detection. Move the slider to the right when improving the
detection accuracy. (Note that higher accuracy setting requires much
more processing time and scanning speed becomes slower.)
2
When using either of the following documents, the automatic page
ATTENTION
size detection may not function correctly:
• Paper of weight 52g/m2 or less
• Not rectangular documents
• Documents which their edges are filled
fi-4220C2 Image Scanner Operator’s Guide
47
Download from Www.Somanuals.com. All Manuals Search And Download.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
DAILY CARE
This chapter describes how to clean the scanner.
WARNING
3
When operating the scanner, the ADF’s glass becomes very hot.
Before you clean inside the scanner, turn off its power and unplug the AC adapter from the
outlet. Wait for at least 15 minutes.
Do not turn off the scanner when you clean the Feed rollers
3.2 Cleaning the Flatbed........................................................................................ 51
fi-4220C2 Image Scanner Operator’s Guide
49
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Cleaning Materials and Locations requiring Cleaning
■ Cleaning Materials
The table below shows the cleaning materials that are used on this scanner.
Cleaning Materials
Part No.
Remarks
1 bottle (100 ml)
Moisten cloth with this fluid and
wipe the scanner clean.
Cleaner F1
(or isopropyl alcohol)
CA99501-0013
Soft, dry cloth
-
-
For details on Cleaner F1, consult the agent where you bought your scanner.
■ Locations and Cycle for Cleaning
Location
Pad ASSY
Standard Cleaning Cycle
Clean every 1000 scanned sheets.
Pick roller
Feed roller
Plastic roller
Glass
Document holding pad
Document bed
The scanner must be cleaned more frequently when the following docu-
ments are used:
ATTENTION
• Documents of coated paper
• Documents with printed text or graphics almost covering the entire surface
• Chemically treated documents such as carbonless paper
• Documents containing a large amount of calcium carbonate
• Documents with Handwritten documents
50
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Cleaning the Flatbed
3.2 Cleaning the Flatbed
Detergent for cleaning windows or glass cleaner can be used instead of
cleaning fluid. However, do not use paint thinner or other organic solvents.
ATTENTION
■ Cleaning the Flatbed
The following parts needs to be cleaned in the Flatbed area:
• Document holding pad
• Document bed
3
Document holding pad
Document bed
fi-4220C2 Image Scanner Operator’s Guide
51
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Open the document cover.
2. Clean the following locations using a soft, dry cloth moistened with cleaning fluid.
Document holding pad
Document bed
•
•
Document holding pad
Wipe gently.
Document bed
Wipe lightly.
Do not allow moisture to get inside the device during cleaning.
ATTENTION
3. Wait for cleaned parts to dry.
4. Gently close the document cover.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Cleaning the ADF
3.3 Cleaning the ADF
As a Guideline, clean the ADF every 1,000 scanned sheets. Note that this guideline varies accord-
ing to the type of documents you scan. For example, it may be necessary to clean the ADF more
frequently if documents are scanned when the toner is not sufficiently fixed on the printout.
CAUTION
The glass surface of the ADF becomes hot during the operation of the scanner.
Before you start to clean the inner parts of the scanner, disconnect the AC adapter from the
power outlet, and wait at least 15 minutes to let the glass cool down.
■ Cleaning the ADF
3
1. Open the ADF by pushing on the ADF button and turning the ADF cover to the front.
ADF Cover
ADF button
CAUTION
Be careful, the ADF cover may close and pinch your finger.
fi-4220C2 Image Scanner Operator’s Guide
53
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Clean the following locations with a soft, dry cloth moistened with Cleaner F1.
Feed rollers (Four pieces)
Pad ASSY
Pick roller (One pieces)
Plastic rollers (Four pieces)
Glass (Two parts)
•
Pad ASSY
Clean the Pad ASSY (rubber surface) downwards (direction of arrow). Take care not to
catch the pick springs to avoid bending.
Pick spring
The portion
to clean
54
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Cleaning the ADF
•
Pick roller
In step 2, all the Feed rollers turn at the same time. When cleaning the Feed rollers
positioned in the lower part of the ADF, be caereful not to touch the other Feed rollers.
Mylar sheet
3
•
Feed roller
1) Open the ADF by pushing on the ADF button.
If you open the ADF cover when the indication of the Function Number display is
"P" or "0", the Feed rollers do not rotate even you perform the operation of step 2)
below. So open the ADF cover when the indication is not "P" or "0".
2) Simultaneously hold down the "Send to" and "Scan" buttons on the operator panel.
The Feed rollers start to rotate slowly.
The location of "Send to" and "Scan" buttons are shown in the following illustra-
tion.
3) Hold a soft, dry cloth moistened with cleaning fluid against the surface of the rotat-
ing Feed rollers so that it lightly cleans the surface of the rollers. Take particular
care when cleaning these rollers as black debris matter on these rollers affects doc-
ument pick performance.
As a guideline, seven presses of the "Send to" and "Scan" buttons make the Feed
rollers to rotate one full turn.
Function No.
display
Function
Send to
Scan
Power button
LED
fi-4220C2 Image Scanner Operator’s Guide
55
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Plastic roller
Clean lightly the surface of these rollers to avoid damaging it. Take particular care
when cleaning these rollers as black debris matter on it affects document pick perfor-
mance. Be careful no to damage the sponges beside the rollers.
CAUTION
In step 2, all the Feed rollers turn at the same time. When cleaning the Feed rollers positioned
in the lower part of the ADF, be caereful not to touch the other Feed rollers.
•
Glass
Clean lightly.
If the glass is dirty, vertical black streaks may apper in the scanned
images.
HINT
3. Press down on the center of the ADF to return it to its original position until the ADF
button locks.
Press center of
ADF
When the ADF has returned to its original position, make sure that it is
ATTENTION
completely closed. Paper jams or feeding errors may occur if the ADF is
not closed completely.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
REPLACING CONSUMABLES
This chapter describes how to replace scanner consumables.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows
XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in
this chapter will differ slightly.
4
WARNING
When operating the scanner, the ADF’s inside glass becomes very hot.
Before you replace the consumables, turn off its power and unplug the AC adapter from the
outlet. Wait for at least 15 minutes.
4.1 Consumable and Replacement Cycle ............................................................ 58
fi-4220C2 Image Scanner Operator’s Guide
57
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Consumable and Replacement Cycle
The following table shows the specifications of consumables and their standard replacement cycle.
Description
Pad Assy
P/N
Standard Replacement Cycle
PA03289-0111
50,000 sheets or one year
Pick roller
PA03289-0001
100,000 sheets or one year
The replacement cycles above are rough guidelines for the case of using A4/Letter woodfree or
wood containing paper 64 g/m2 (17 lb). This cycle varies according to the type of the used paper
and how frequently the scanner is used and cleaned.
Use only the specified consumables. Do not use other consumables.
ATTENTION
58
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Consumable and Replacement Cycle
■ Guidelines for Consumable Replacement Cycle
With this product, you can learn how many times the consumables are used so that you can esti-
mate the right timing for the replacement.
• For Windows 98 / Windows Me / Windows 2000 / Windows XP
1. When turning on the power, check that the scanner is connected to the PC.
Refer to "2.2 Connecting the Scanner to a PC" in fi-4220C2 Getting Started on the Setup
CD-ROM for information about connecting the scanner to a personal computer.
2. Double click the "Printer and Other Hardware" icon on the operator panel of the host
computer.
4
⇒ The [Printer and Other Hardware] screen is displayed.
3. In the [Printer and Other Hardware] screen, double click the "Scanners and Cameras"
icon.
⇒ The [Scanners and Cameras] screen is displayed.
fi-4220C2 Image Scanner Operator’s Guide
59
Download from Www.Somanuals.com. All Manuals Search And Download.
4. On "fi-4220C2dj" icon, right click and select [Properties] (for Windows Me, Windows XP),
or double click (for Windows 98, Windows 2000)
⇒ The [fi-4220C2dj Properties] dialog box appears.
5. Click the "Device Set" tab.
⇒ The following screen is displayed.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Consumable and Replacement Cycle
You can confirm the following information in this panel:
•
•
•
Total number of scans
Pad counter (approximate number of scans after resetting the pad counter)
Pick roller counter (approximate number of scans after resetting the Pick roller counter)
• For Windows 95 / Windows NT 4.0
1. When turning on the power, check that the scanner is connected to your PC.
2. Right click the "FUJITSU Scanner Control Center" icon displayed in the task tray, then
select "Option".
3. Click "Device Setting" tab.
⇒The following screen is displayed.
4
You can confirm the following information in this panel:
•
•
•
Total number of scans
Pad counter (approximate number of scans after resetting the pad counter)
Pick roller counter (approximate number of scans after resetting the Pick roller counter)
fi-4220C2 Image Scanner Operator’s Guide
61
Download from Www.Somanuals.com. All Manuals Search And Download.
The following message sometimes appears when the scanner is being used:
Replace consumables when this message is displayed.
■ When Replacing Consumables Immediately
1. To replace consumables after completing the scanning of all the document sheets in
the ADF, click the [Ignore] button.
To abort scanning and replace the consumables immediately, click the [Cancel] button.
2. Replace the consumables.
For details on how to replace consumables, see "4.2 Replacing the Pad Assy" (page. 63) and
3. To disable display of this message, mark the "This message not display again" checkbox.
Note that when the "This message not display again" checkbox is marked, this message is not
displayed until the consumables counter is reset.
■ When Consumables Cannot Be Replaced Immediately
1. To continue scanning of the current document, click the [Ignore] button.
To discontinue scanning, click the [Cancel] button.
2. Replace the consumable as soon as possible.
For details on how to replace consumables, see "4.2 Replacing the Pad Assy" (page. 63) and
3. To disable display of this message, mark the "This message not display again" checkbox.
Note that when the "This message not display again" checkbox is marked, this message is not
displayed until the consumables counter is reset.
To display the message again after scanning 100 sheets, mark the [Warms again after scanning
100 pages] checkbox.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Replacing the Pad Assy
4.2 Replacing the Pad Assy
1. Remove any documents on the ADF paper chute.
2. Open the ADF by pushing the ADF button.
ADF Cover
ADF button
4
CAUTION
Be careful, the ADF cover may close and pinch your finger.
3. Remove the Pad ASSY.
Press the knobs on both ends of the Pad ASSY, and pull the Pad ASSY upwards and towards
you.
When doing this, take care not to catch the pick springs.
Pick spring
4. Attach the new Pad ASSY.
Hold both ends of the new Pad ASSY and attach it to its installation location.
When doing this, take care not to catch the pick springs.
Make sure that the Pad ASSY is firmly attached. When the Pad ASSY is
ATTENTION
not correctly attached, document jams or other feeding errors may occur.
fi-4220C2 Image Scanner Operator’s Guide
63
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Press down on the center of the ADF to return it into its original position and lock the
ADF button.
Press center of
ADF
6. Reset the pad counter.
•
For Windows 98 / Windows Me / Windows 2000 / Windows XP
1) When turning on the power, check that the scanner is connected to your PC.
2) Open the [Scanners and Cameras] from the control panel of your PC.
3) Open the [Properties] of [fi-4220C2dj] from the [Scanners and Cameras].
4) The [fi-4220C2dj Properties] dialogbox appears.
5) Click the "Device Set" tab.
⇒ The following screen is displayed.
6) After clicking the [Clear] button beside "Pad" in "Page Counter", click the [OK]
button.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Replacing the Pad Assy
⇒ The following panel appears.
Click the [OK] button.
This returns the pick counter to "0".
•
For Windows 95 / Windows NT 4.0
1) When turning on the power, check that the scanner is connected to your PC.
2) Right click the "FUJITSU Scanner Control Center" icon displayed in the task tray,
then select "Option".
3) Click the "Device Setting" tab.
⇒ The following screen is displayed.
4
4) After clicking the [Clear] button beside "Pad" in "Page Counter", click the [OK]
button.
⇒ The following message is displayed.
Click the [OK] button.
The Pad counter returns to "0".
fi-4220C2 Image Scanner Operator’s Guide
65
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
1. Remove any documents on the ADF paper chute.
2. Remove the ADF paper chute.
3. Open the ADF by pushing the ADF button.
The front portion
ADF button
CAUTION
Be careful, the ADF cover may close and pinch your finger.
4. Remove the Pick roller from the scanner.
1) Grip the knobs on the sheet guide with your fingers, and lift it up to remove.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
2) Rotate the Pick roller bushing in the direction of the arrow.
Pick roller bushing
4
3) Remove the Pick roller while lifting it up in the direction of the arrow.
CAUTION
The Pick roller Bushing is hard. Do not turn this bearing with your fingernails.
Use a paper clip for turning the roller bushing If you can not rotate it with your finger.
fi-4220C2 Image Scanner Operator’s Guide
67
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the Pick roller from the shaft while lifting up the tab on the Pick roller.
Pull out the shaft from the pick roller while lifting up its tab.
Tab
Shaft
Pick Roller
If you push up the pick roller tab using your fingernail, it may heart or
ATTENTION
get chipped your fingernail. If you worry about that, you push up the
pick roller tab using a paper clip.
1
2
6. Attach the new Pick roller.
Insert the new Pick roller aligning the protrusion on the shaft with the slot for the screw in
the Pick roller.
Protrusion
Slot
68
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
Make sure that the Pick roller is completely attached. An incompletely
attached Pick roller might cause document jams or other feed errors.
When attaching the Pick roller, make sure that the roller clicks in to
place.
ATTENTION
"Click"
7. Attach the Pick roller to the scanner.
Attatch the Pick roller to the scanner in reverse order of the procedure for removing.
1) Turn the Pick roller bushing in the direction indicated by the arrow.
4
Pick roller bushing
2) Move the sheet guide claws in the direction indicated by the arrow to fix the sheet guide.
fi-4220C2 Image Scanner Operator’s Guide
69
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press down the center of the ADF to return it to its original position and lock the ADF
button.
Press center of
ADF
9. Attach the ADF paper chute.
ADF paper chute
70
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
10. Reset the pick counter.
For Windows 98 / Windows Me / Windows 2000 / Windows XP
•
1) When turning on the power, check that the scanner is connected to your PC.
2) Open the [Scanners and Cameras] from the control panel of your PC.
3) Open the [Properties] of [fi-4220C2dj] from the [Scanners and Cameras].
4) The [fi-4220C2dj Properties] dialogbox is displayed.
5) Click the "Device Setting" tab.
⇒ The following panel appears.
4
6) After clicking the [Clear] button beside "Pick Roller" in "Page Counter", click the
[OK] button.
⇒ The following panel appears.
Click the [OK] button.
This returns the pick counter to "0".
fi-4220C2 Image Scanner Operator’s Guide
71
Download from Www.Somanuals.com. All Manuals Search And Download.
•
For Windows 95 / Windows NT 4.0
1) When turning on the power, check that the scanner is connected to your PC.
2) Right click the "FUJITSU Scanner Control Center" icon displayed in the task tray,
then select "Option".
3) Click the "Device Setting" tab.
⇒ The following screen is displayed.
4) After clicking the [Clear] button beside "Pick Roller" in "Page Counter", click the
[OK] button.
⇒ The following message is displayed.
Click the [OK] button.
The Pick counter (The Pick roller counts) returns to "0".
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
TROUBLESHOOTING
This chapter describes how to remedy document jams, other trouble, items to check before contact-
ing the agent where you bought the scanner, and how to check device labels.
About troubles that are not described here, and the details of the errors,
ATTENTION
refer to the FUJITSU TWAIN32 Scanner Driver Help.
5
5.1 Removing Jammed Documents...................................................................... 74
5.4 Checking Labels on the Scanner.................................................................... 92
fi-4220C2 Image Scanner Operator’s Guide
73
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 Removing Jammed Documents
If a document jam occurred, follow the procedure below to remove the jammed documents.
CAUTION
• Take care not to get injured when removing jammed documents.
• Be careful not to get neckties, necklaces, etc. entangled in the scanner when removing the
jammed documents
• The surface of the glass may become hot during operation. Take care not to get burned.
1. Remove any documents on the ADF paper chute.
2. Open the ADF by pushing on the ADF button.
ADF Cover
ADF button
CAUTION
Be careful, the ADF cover may close and pinch your finger.
3. Remove the jammed document.
• Staples, paper clips, etc. cause document jams. Be sure to fully
ATTENTION
check the document and feed path, and remove any small metal
objects such as these.
Also, before you start scanning, be sure to remove any staples,
clips, etc. from the document.
• Take care not to pull the pick springs when removing jammed doc-
uments.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 Removing Jammed Documents
4. Press down on the center of the ADF to return it to its original position and lock the
ADF button.
Press center of
ADF
• Make sure that the ADF is completely closed. When it is not com-
ATTENTION
pletely closed, document jams or feeding errors may occur.
• When the scanning is completed or canceled, the documents might
remain inside the ADF even though any error message is not dis-
played.
Follow the procedure below to remove the documetns remaining in
the ADF.
1. Remove all documents from the ADF paper chute.
2. Open the ADF by pushing down the ADF button.
3. Remove the remaining documents.
5
4. Push in the center of the ADF to close it until the ADF button is
locked.
If a document jam or Multi Feed errors occur frequenlty, follow the procedures below .
1. Align the edges of the document sheets.
fi-4220C2 Image Scanner Operator’s Guide
75
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Hold both the left and right sides of the document with both hands, and, as shown
below, bend the document, bring back and release one side of the stack.
(4106ꢀ5+&'
3. The document edges will be slightly misaligned, as shown in the picture.
4. Load the documents into the ADF chute, as shown in the picture.
Roller
76
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
5.2 Remedying Typical Troubles
This section describes troubles that may occur during scanning and how to remedy that trouble.
Before you ask for repair, check the following flowcharts.
If the remedies in these flowcharts do not solve the problem, check the items in "5.3 Items to
the agent where you bought the scanner.
Scanner cannot be turned ON.
Symptom 1
NO
Are power cable and AC adapter
correctly connected?
Correctly connect power cable.
YES
You must use the AC adapter
and cable supplied with your
scanner by the manufacturer.
Please get the correct AC
adapter and cable to connect
to your scanner.
NO
NO
Are you using the correct AC cable
and AC adapter supplied with the
scanner from the manufacturer?
5
YES
Did you pushed the power
button?
Press power button.
YES
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
fi-4220C2 Image Scanner Operator’s Guide
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Indication on Function No. display goes out.
Symptom 2
The scanner operation is
normal.
NO
Does the display remain blank
even after you push any button
on the operator panel?
YES
Scanner operation is
normal.
NO
Does the display remain blank
even after running ON the scanner
again?
YES
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
The scanning does not start.
Symptom 3
NO
NO
Turn OFF the scanner and
unlock the shipping lock. (*1)
Did you unlock the shipping lock
of the flatbed?
YES
Load document correctly on
ADF paper chute.
Are the document loaded correctly
on the ADF paper chute?
YES
NO
NO
Close the ADF completely.
Is the ADF closed completely?
YES
Connect interface cable
correctly. (*2)
Is the interface cable connected
correctly?
YES
YES
NO
Use a new interface cable
and correctly connect it.
Is the connector of interface
cable broken?
5
NO
Turn OFF the scanner and set
the SCSI ID correctly, then
turn ON the scanner again.
(*2)
(when using scanner on SCSI
interface)
Is the SCSI ID set correctly?
YES
YES
Does the scanning start after
running ON the scanner again?
The scanner operation is
normal.
NO
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
*1) For details, refer to "Getting Started" 2.1 Installing the Scanner.
*2) For details, refer to "Getting Started" 2.2 Connecting the scanner to your PC.
fi-4220C2 Image Scanner Operator’s Guide
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Quality of scanned pictures or photos is
not satisfactory.
Symptom 4
NO
Did you select
halftoning or dithering?
Select halftoning or dithering
on your PC.
YES
NO
Are the upper/lower glasses inside
the ADF, the document bed, and
the document holding pad clean?
Clean dirty locations. (*)
YES
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
*) For details on how to clean dirty locations, see "Chapter 3 DAILY CARE" (page. 49).
Quality of scanned text or lines is unsatisfactory.
Symptom 5
NO
Are the upper/lower glasses inside
the ADF, the document bed, and
the document holding pad clean?
Clean dirty locations. (*)
YES
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
*) For details on how to clean dirty locations, see "Chapter 3 DAILY CARE" (page.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Images are distorted or blurred.
Symptom 6
NO
Are the upper/lower glasses inside
the ADF, the document bed, and
the document holding pad clean?
Clean dirty locations. (*)
YES
YES
Do not press down the ADF
or place heavy object on
the ADF during scanning.
Is the ADF cover pressed down or
heavy object placed on the ADF
during scanning?
NO
YES
NO
Do not allow anything to
cause the scanner to
vibrate while scanning.
Is something causing the scanner
to vibrate during scanning?
NO
5
Install the scanner on
a flat, level surface.
Is the scanner installed on a flat,
level surface?
YES
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
*) For details on how to clean dirty locations, see "Chapter 3 DAILY CARE" (page.
fi-4220C2 Image Scanner Operator’s Guide
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical lines appear in the scanned image.
Symptom 7
YES
Did you scan the document
with the Flatbed?
Clean the document bed of
the Flatbed. (*1)
NO
YES
YES
Is the glasses of the ADF Dirty?
Clean the upper/lower
glasses inside the ADF.(*2)
NO
Do the lines disappear on images
with low resolution settings?
Scan the documents with
low resolution settings.
NO
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
*1) For cleaning the Flatbed, refer to "3.2 Cleaning the Flatbed" (page. 51).
*2) For cleaning the inside of the ADF, refer to "3.3 Cleaning the ADF" (page. 53).
82
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
The Function No. display indicates alarm after
the scanner is turned ON.
Symptom 8
NO
NO
Turn OFF the scanner and
unlock the shipping lock, then
turn ON the scanner again.(*)
(When the scanner is just installed
on the place) Did you unlock the
shipping lock of the flatbed?
YES
Does the Function No. display
indicate any alarm after turning ON
the scanner again?
The scanner operation is
normal.
YES
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
5
FUJITSU service provider.
*) For details, refer to "Getting Started" 2.1 Installing the Scanner.
fi-4220C2 Image Scanner Operator’s Guide
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi feed errors occur frequently.
Symptom 9
NO
NO
Do the documents satisfy the
conditions described in
"6.2 Document Quality"?
Use documents that satisfy
the requirements. (*1)
YES
When the multi feed detection is
ON, are the multi feed detection
conditions satisfied?(*2)
Satisfy the multi feed
detection conditions. (*2)
YES
NO
YES
NO
Fan the document before
loading, or reduce the number
of sheets of the documents.
Were the documents fanned
before loaded onto the ADF
paper chute?
YES
Fan the documents 3 or 4
times to remove static
electricity from the paper.
Have the documents just been
printed out on a copier or laser
printer?
NO
Reduce the number of sheets
of the document. (*3)
Is the document stack 5 mm
or less?
YES
Continued on next page
84
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Continued from previous page
NO
Are all the consumables
(Pick roller and Pad Unit) installed
correctly?
Correctly install the
consumables if needed.
YES
YES
YES
Is any of consumables
(Pick roller and Pad Unit) dirty?
Clean the dirty consumables.
(*4)
NO
Is any of consumables (Pick roller
and Pad Unit) worn out? (Check
the consumable counter)
Replace the consumable,
if needed. (*5)
NO
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
5
FUJITSU service provider.
*1) For details on requirements, see "6.2 Document Quality" (page. 95).
*2) For details on multi feed, see "6.5 Multi feed Detection Conditions" (page. 99).
*3) For details on requirements, see "6.3 Maximum Document Loading Capacity"
*4) For details on how to clean the consumables, see "3.3 Cleaning the ADF" (page.
53).
*5) For details on how to replace and attach consumables, see "4 REPLACING CON-
fi-4220C2 Image Scanner Operator’s Guide
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Pickup errors occurs frequently.
Symptom 10
Do the documents satisfy the
conditions described on
"6.2 Document Quality"?
NO
NO
Use documents that satisfy
the requirements.(*1)
YES
Fan the document before
loading, or reduce the number
of sheets of the documents.
Were the documents fanned
before loading on ADF paper
chute?
YES
Correctly install the
consumable(Pick roller and
Pad Unit), if needed. (*2)
NO
Are all the consumables
(Pick roller and Pad Unit)
installed correctly?
YES
YES
Is any of consumables
(Pick roller, Pad Unit) dirty?
Clean the dirty consumable.
(*3)
NO
YES
Is any of consumables (Pick roller
and Pad Unit) worn out? (Check
the consumable counter)
Replace the consumable,
if needed. (*4)
NO
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
*1) For details on requirements, see "6.2 Document Quality" (page. 95).
*2) For details on how to install the consumables, see "4 REPLACING CONSUM-
*3) For details on how to clean the consumables, see "3.3 Cleaning the ADF" (page.
*4) For details on how to replace the consumables, see "4 REPLACING CONSUM-
86
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Paper jams occur frequently
Symptom 11
NO
Do the documents satisfy the
conditions described in
"6.2 Document Quality"?
Use the document that
satisfy the requirements. (*1)
YES
YES
NO
Clean the ADF or remove
debris from the ADF. (*2)
Is there any debris in the ADF?
NO
Correctly install the
consumables (Pick roller and
Pad Unit), if needed. (*3)
Are all the consumables
(Pick roller and Pad Unit)
installed correctly?
YES
YES
YES
Is any of consumables
(Pick roller, Pad Unit) dirty?
Clean the dirty consumable.
(*2)
NO
5
Is any of consumables (Pick roller
and Pad Unit) worn out? (Check
the consumable counter)
Replace the consumable,
if needed. (*3)
NO
If you cannot solve the problem
after taking measures, check the
items in "5.3 Items to check before
contacting the dealer where you
bought the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
*1) For details on requirements, see "6.2 Document Quality" (page. 95).
*2) For details on how to clean the ADF, see "3.3 Cleaning the ADF" (page. 53).
*3) For details on how to attach the consumables, see "4 REPLACING CONSUM-
fi-4220C2 Image Scanner Operator’s Guide
87
Download from Www.Somanuals.com. All Manuals Search And Download.
The scanned images are elongated
Symptom 12
NO
Have you cleaned all the
rollers?
Clean all the rollers. (*)
YES
Check the items in "5.3 Items
to check before contacting
the dealer where you bought
the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
YES
Have you adjusted the scan
scale?
NO
Set the scan scale.
Which OS do you use?
Windows 95/
Windows NT 4.0
Windows 98/
Windows Me/
Windows 2000/
Windows XP
YES
Is the Scanner Control Center
icon displayed in the task tray?
Display the properties of
the scanner that you are
using on "Scanners and
Cameras" in the control
panel, then adjust the
scan scale.
NO
Select [FUJITSU Scanner Control
Center] from the Start menu and
run it.
Right click the Scanner
Control Center icon and select
[Options] then adjust the scan
scale.
*) For details on how to clean the rollers, see "3.3 Cleaning the ADF" (page. 53).
88
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
There is a shadow on the leading edge of
the scanned images.
Symptom 13
YES
Check the items in "5.3 Items
to check before contacting
the dealer where you bought
the scanner" and contact
the dealer or an authorized
FUJITSU service provider.
Did you adjust the offset
(starting position for scanning
the document)?
NO
Adjust the offset.
Which OS do you use?
Windows 98/
Windows Me/
Windows 2000/
Windows XP
Windows 95/
Windows NT 4.0
YES
Is the Scanner Control Center
icon displayed in the task tray?
Display the properties of
the scanner that you are
using on "Scanners and
Cameras" in the control
panel, then adjust the
[Sub-scan Setting].
NO
5
Select [FUJITSU Scanner Control
Center] from the Start menu and
run it.
Right click the Scanner
Control Center icon and
select [Options] then
adjust the [Sub-scan Setting].
fi-4220C2 Image Scanner Operator’s Guide
89
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Items to Check Before Contacting the Agent Where
You Bought the Scanner
Check the following items before you contact the agent where you bought the scanner.
■ General Details
Item
findings
Model
(Example) fi-4220C2
For details on model, see "5.4 Checking Labels on
Serial No.
(Example) 000001
For details on serial No., see "5.4 Checking Labels
Production date
(Example) 2004-5 (May, 2004)
For details on production date, see "5.4 Checking
Date of purchase
Symptom
Frequency of trouble
90
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Items to Check Before Contacting the Agent Where You Bought the Scanner
■ Installation or PC connection issues
■ Problem at the time of personal computer connection
Item
findings
OS (Windows)
Displayed error message
Application
(Example) SCSI interface
Interface controllers
(Example) made by Adaptec
SCSI Card 2940AU
■ Feed system trouble
Item
findings
Document type
Main purpose of use
Last cleaning date
Last consumables replacement date
Operator panel status at trouble
5
■ Imaging system trouble
Item
findings
Type and version of scanner driver
Type of interface controller
(Example) made by Adaptec
SCSI Card 2940AU
OS (Windows)
Application software
(Example) ScandAll 21
(Example) Acrobat
■ Other
Item
findings
Can both the original document and scan-
ner image be sent by e-mail or Fax?
fi-4220C2 Image Scanner Operator’s Guide
91
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 Checking Labels on the Scanner
This section describes how to check the labels on the scanner.
■ Positions of Labels on the Scanner
The following shows where the two labels are located on the scanner.
Label B
Label A
Label A (example): Indicates scanner information.
Label B (example): Indicates various standards that the scanner conforms with.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2 Document Quality
6.2 Document Quality
■ Document Type
The following paper types are recommended for document use:
6
• Woodfree paper
• Wood containing paper
When using documents of paper type other than the above, check whether or not the document can
be scanned by test-scanning a few sheets before executing the actual document.
■ Document Thickness
Paper thickness is expressed by "paper weight." The following shows the paper weights that can be
used on this scanner:
• 52 g/m2 to 127 g/m2
Only paper weight of 127 g/m2 is acceptable for A8-size documents.
■ Precautions
The following documents may not be scanned successfully:
• Documents of non-uniform thickness (e.g. envelopes)
• Folded or torn documents
• Tracing paper
• Coated paper
• Carbon paper
• Carbonless paper
• Photosensitive paper
• Perforated or punched documents
• Documents that are not square or rectangular
• Very thin documents
Do not use the following documents:
• Paper-clipped or stapled documents
• Documents on which the ink is still wet
• Documents smaller than A8 (Portrait) in size
• Documents wider than A4 or Letter size (216mm)
• Documents other than paper such as fabric, metal foil, or transparencies
fi-4220C2 Image Scanner Operator’s Guide
95
Download from Www.Somanuals.com. All Manuals Search And Download.
• When scanning semi-transparent documents, slide the [Brightness] bar to
light to avoid bleed through.
HINT
• To prevent the rollers from becoming dirty, avoid scanning documents con-
taining large areas written or filled in pencil. If scanning of such documents
is unavoidable, clean the rollers frequently.
• Carbonless paper contains chemical substances that may damage the
Pad ASSY or rollers (e.g. Pick roller) when documents are fed. Pay atten-
tion to the following:
ATTENTION
Cleaning:
If pick errors occur frequently, clean the Pad ASSY and
Pick rollers.
For details on cleaning the Pad ASSY and Pick rollers,
Replacing parts: The service life of the Pad ASSY and Pick rollers is
sometimes shortened when scanning medium-grade
paper documents.
• When the manuscript of Wood containg paper is read, the life of a Pad
ASSY and a Pick roller may become short compared with the case where
the manuscript of Woodfree paper is read.
When using the ADF, the leading edge of all document sheets must be
evenly aligned. Make sure that curling at the leading edge is within the fol-
lowing tolerances:
HINT
More than 30mm
Feed direction
Less than
3mm
Top of the paper
Read surface
Feed direction
More than 30mm
Less than
5mm
Top of the paper
Read surface
96
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3 Maximum Document Loading Capacity
6.3 Maximum Document Loading Capacity
The maximum number of sheets that can be loaded on the ADF paper chute is determined by the
size and weight of the document. The following graph shows the maximum document loading
capacity of ADF according to paper weight.
6
60
60
50
40
30
20
A4 / Letter or smaller
Legal
50
41
50
Capacity of ADF
(number of
pages)
35
29
29
24
0
52 64
80
104
127
Paper weight (g/m2 )
Paper weight conversion table
Conversion
Unit
2
52
14
64
17
75
20
80
21
90
24
104
28
127
34
g/m
lb
fi-4220C2 Image Scanner Operator’s Guide
97
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4 Area not to be perforated
When using the ADF, document trouble might occur if there are punched holes in the shaded area
in the following figure. If hole-punched documents must be scanned, use the Flatbed.
35
Read reference
position
Top of paper
Front side
Feeding
direction
Bottom of paper
(Unit : mm)
Center of paper
98
Download from Www.Somanuals.com. All Manuals Search And Download.
6.5 Multi feed Detection Conditions
6.5 Multi feed Detection Conditions
There are three multi feed detection modes: document thickness, document length, and both docu-
ment thickness and length. The following conditions must be satisfied in each of these detection
modes.
6
■ Detection by Document Thickness
Sheets of the same thickness shall be set in the ADF at a time.
• Document thickness: 0.065 to 0.15mm
• Printed area: 12% or less
• No black printed areas are allowed at the center area (26 x 10mm) at the leading edge of the
document.
• Punched holes are not allowed within 35mm of the vertical center line of the document.
• The deviation in the amount of the light transmitted through background areas must not be
less than 10%.
■ Detection by Document Length
Sheets of the same length shall be set in the ADF at a time.
• Document length deviation: 1% or less
• Punched holes are not allowed within 35mm of the vertical center line of the document.
■ Detection by Document Thickness and Length
Sheets of the same thickness and length shall be set in the ADF at a time.
• Document thickness: 0.065 to 0.15mm
• Document length deviation: 1% or less
• Printed area: 12% or less
• No black printed areas are allowed at the center area (26 x 10mm) at the leading edge of the
document.
• Punched holes are not allowed within 35mm of the vertical center line of the document.
• The deviation in the amount of the light transmitted through background areas must not be
less than 10%.
fi-4220C2 Image Scanner Operator’s Guide
99
Download from Www.Somanuals.com. All Manuals Search And Download.
The type of document and document conditions sometimes cause the multi
feed detection rate to drop.
HINT
35mm
26mm
10mm
No printing allowed
Feeding direction
No punched holes
allowed
Center of paper
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
SCANNER SPECIFICATION
This chapter lists the scanner specifications.
7
7.2 Installation Specifications............................................................................. 104
7.3 External Dimensions...................................................................................... 105
fi-4220C2 Image Scanner Operator’s Guide
101
Download from Www.Somanuals.com. All Manuals Search And Download.
7.1 Basic Specifications
1
Scanner Type
ADF(Automatic Document
Feeder),Flatbed
-
2
3
Image sensor
Light source
CCD x 3
Front / Back / Flatbed
Front / Back / Flatbed
White cold cathode fluores-
cent lamp x 3
2
4
Scanning
area
Minimum
Maximum
A8 (Portrait)
ADF 127 g/m paper
(Note (*1))
Flatbed: 216 x 297mm
(8.50 x 11.69in)
ADF: Legal
-
(Long page scanning:
216 x 864mm or
8.50 x 34in)
2
2
5
6
Paper Weight
(Note (*2))
52 g/m to 127g/m
(14 to 34lb)
Scanning
Speed
Binary
Simplex: 25 sheets/min.
200 dpi
(monochrome) Duplex: 50 sides/min.
(Note (*4))
(A4 Portrait)
(Note (*3))
Color
Simplex: 25 sheets /min.
Duplex: 50 sides/min.
150 dpi
(Note (*4))
2
7
Capacity of ADF
50 sheets
A4, 80 g/m (20lb)
(Note (*5))
8
9
Optical Resolution
600 dpi
-
Output reso- Binary
50 - 600 dpi
Scalable in 1 dpi incre-
ments
lution
(monochrome)
Grayscale
50 - 600 dpi
50 - 600 dpi
8 bits per color
Scalable in 1 dpi incre-
ments
Color
Scalable in 1 dpi incre-
ments
10
Grayscale level
(internal)
Internal 10 bits
11
12
Halftone Patterns
Dither / error diffusion
Ultra SCSI
-
Interface
Shield-type 50 pin (pin-
type) halfpich
(Note (*6))
USB 2.0 / 1.1 (Note (*7))
JPEG compression
B type
-
13
Other function
102
Download from Www.Somanuals.com. All Manuals Search And Download.
7.1 Basic Specifications
*1) The minimum size for scanning is A8 when using the ADF. When using the Flat-
bed to scan the minimum scanning range is virtually unlimited.
*2) The manuscript thicknesses noted are for when using the ADF. When using the
Flatbed to scan the manuscript thickness is unlimited.
For details, see "Chapter 6 ADF AND PAPER SPECIFICATION" (page. 93).
*3) The scanning speed is the maximum speed of the scanner hardware. Software pro-
cessing time such as data transfer time is added to the actual scanning time.
*4) The scanning speed noted is the value when using the ADF to scan.
*5) The maximum stacking capacity varies according to the document thickness. For
details, see "Chapter 6 ADF AND PAPER SPECIFICATION" (page. 93).
*6) The Ultra SCSI and USB 2.0 / 1.1 interfaces cannot be used at the same time.
*7) If you connect the scanner with USB 2.0, it is required that the USB port and the
Hub are compliant with USB 2.0. The scanning speed may slow down when you
connect the scanner with USB 1.1. If your omputer has the compatible USB 2.0
port, please use it.
7
fi-4220C2 Image Scanner Operator’s Guide
103
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2 Installation Specifications
Item
Specification
Width
Dimensions (mm)
Depth
Height
(Without ADF paper chute)
569 (22.4 in) 302 (11.9 in)
229 (9.0 in)
Installation Space (mm)
(D x W x H)
800 (31.5 in) x 400 (15.8 in) x 450 (17.8 in)
Weight (kg)
8.0 (17.64 lb)
Input
Voltage
100 to 120 VAC ±10%
220 to 240 VAC ±10%
power
Phases
Single-phase
50 / 60 ± 3Hz
34 W or less
Frequency
Power consumption
Installation Space is the reference value of an installation space
required to read A4 manuscript.
ATTENTION
Item
Device status
Specification
Ambient
condition
Operating
Not operating
Temperature
Humidity
5 to 35 °C (41 to 95°F)
20 to 80 %
-20 to 60 °C (-4 to 140°F)
8 to 95 %
Heat capacity
29.3 kcal / H or less
11.5 (25.35 lb)
Shipping Weight (kg)
104
Download from Www.Somanuals.com. All Manuals Search And Download.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
Before using the [Scan] or the [Send to]
button
By setting the link of the application software to the [Scan] or [Send to] button, you can launch the
linked application by simply pushing the button.
■For Windows 98, Windows Me, Windows 2000, Windows XP
A
1. Select [Start]-[Control Panel].
2. Select [Scanners and Cameras]-[Properties].
3. Select the [Events] tab.
4. Select an Event. For Windows XP, select the event for starting up any application
from the [Select an event] menu.
The events available for this function are:
- Scan button (When pushing the [Scan] button)
- Feeder loaded with paper (When setting the documents in the ADF)
- Send to 1-9 (When pushing the [Send] to button)
fi-4220C2 Image Scanner Operator’s Guide
AP-1
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select the application with its process, excuted by the event. For Windows XP, click
[Start this program] under [Actions] and select the application and process from the
menu.
6. Click [OK] button.
A window may appear when documents are set on the ADF.
If you wish not to display this window, select [Feeder loaded with paper]
HINT
from [Select an event] and click [Take no action], then click [OK].
The window and operations may vary depending on your OS.
HINT
AP-2
Download from Www.Somanuals.com. All Manuals Search And Download.
■For Windows 95, WindowsNT 4.0
1. Right click the [FUJITSU Scanner Control Center] in the task tray and select [Option].
2. Select the event for starting up the application from the [Event] menu.
A
The events available for this function are:
- Start/Scan button (When pushing the [Scan] button)
- Send to 1-9 (When pushing the [Send] to button)
3. Click [...] button right to the entry field of [Path].
4. Click [OK].
fi-4220C2 Image Scanner Operator’s Guide
AP-3
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-4
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
A4 size
A standard paper size. Paper size is 210 x 297 mm.
A5 size
A standard paper size. Paper size is 148 x 210 mm.
A6 size
A standard paper size. Paper size is 105 x 148 mm.
A7 size
A standard paper size. Paper size is 74 x 105 mm.
A8 size
A standard paper size. Paper size is 53 x 74 mm.
ADF (Automatic Document Feeder)
A unit that allows the user to scan a number of pages consecutively. Fed documents are
transported from the ADF paper chute (or hopper) to the Stacker. Actual scanning opera-
tion is executed by the mechanism inside of this unit. Backside reading = Back-side
scanning Refers to reading the backside of the document, specifically in Duplex reading
mode.
Automatic separation
An image processing method in which the scanner automatically detects difference
between text and photos, and chooses the threshold accordingly. This function allows
the scanner to switch between line mode and half tone mode in one pass.
Automatic size/skew detection
A function that automatically detects the documents' page size and adjusts output data to
the detected page size. Document skewing is automatically detected and corrected for
the output image.
fi-4220C2 Image Scanner Operator’s Guide
GL-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Brake roller
A roller that prevents two or more sheets of paper from being fed simultaneously into the
ADF.
Brightness
Refers to the brightness of scanned images in this manual.
Canadian DOC Regualtions
"A standard issued by Industry Canada, a department of the Canadian government,
which sets out the technical requirements relative to the radiated and conducted radio
noise emissions from digital apparatus. "
CCD (Charged Coupling Device) Image Sensor
A semiconductor device inside the scanner that registers light reflected from the original
image and converts it into a digitized (electronic) form. CCD technology is the basis of
high-quality image acquisition in scanners, cameras, and other specialized devices.
Cleaning paper
Sheets used with the F1 cleaner for cleaning the rollers (pick rollers, feed rollers, etc.)
and complete document path in the scanner. Used in daily maintenance of the low vol-
ume production scanner to reduce paper transport problems. Note: these sheets are not
meant to replace the more thorough periodic cleaning of the scanner.
Cleaning sheet
Adhesive sheets used for cleaning the rollers (pick rollers, feed rollers, etc.) and com-
plete document path in the scanner. Used in daily maintenance of the high volume pro-
duction level scanner to reduce paper transport problems. Note: these sheets are not
meant to replace the more thorough periodic cleaning of the scanner.
Color balance
Balance of colors in images.
Default settings
Pre-set values for optional menus.
Density
In this manual, refers to a measurement of the depth of the display.
GL-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Dither
The process by which a group of dots is arranged to represent a shade of gray. The pre-
determined dot pattern simulates shades of gray. This scanning process offers the
advantage of reduce memory requirements compared to multilevel gray.
Document jam
A warning that appears when document is jammed in the transport unit, or transportation
is Interupted because the paper is slipping.
dpi
Dots per inch. Number of dots lined along one inch A measurement of resolution nor-
mally used for scanners and printers. Higher dpi means better resolution.
Driver software
In this manual, driver software refers to software that allows the scanning application
software to communicate with the scanner.
Dropout color
A color which is used in the document but does not appear in the read image.
Duplex reading mode
A mode for scanning both sides of the document in one pass.
Eject rollers
Rollers that transport documents from the ADF onto the Stacker.
Energy Star
ENERGY STAR is an international standard for energy-efficient electronic equipment. It
was created by the US Environment Protection Agency (EPA) in 1992. The standard pro-
gram has now been adopted by several countries around the world.
Equipment Error
An error that cannot be fixed by the operator. The operator should call the manufacturer
for service.
fi-4220C2 Image Scanner Operator’s Guide
GL-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Error diffusion
High-quality halftone (pseudo-grayscale) image production based on black-and-white
pixel binarization. A pixel's optical density and that of adjacent pixels are summed, with
black pixels relocated in their order of density as they relate to adjacent pixels. The pur-
pose of this technique is to minimize the average error between read and printed densi-
ties. Density data for adjacent pixels is modified by diffusing errors on the objective pixel
into several pixels, which are then binarized. This maintains high grayscale levels and
resolution during reading, while suppressing more patterns by dotted halftone images
such as newspaper photographs.
FCC
Acronym for "The Federal Communications Commission", an independent United States
government agency which is in charge of regulating interstate and international commu-
nications via radio, television, wire, satellite and cable. The Part 15 of the FCC regula-
tions mentioned in this manual is designed to prevent harmful interferences on radio
communication of radio receivers and other devices which radiate radio frequency
energy, and provides for the certification of radio receivers. It also provides the certifica-
tion of low power transmitters and the operation of certificated transmitters without a
license.
Feeds rollers
Rollers that feed documents through the ADF.
Filtering
A correction method that improves the read quality of handwritten documents. The read
quality of images written in pencil or ball-pointed pen depends on the reflective light
characteristics of the specific ink or lead used. Dropped pixels may produce outlines,
gaps, or thin, barely connected lines due to uneven optical density. Filtering detects
areas lighter than their surroundings and increases their density to improve image clarity.
Flat bed An input device of the scanner, where documents are placed and scanned.
Generally used for scanning pages out of a book, or paper that is out of the feeding
specification of the ADF. Also used to scan a small volume of documents by manual
operation.
Flat bed
An input device of the scanner, where documents are placed and scanned. Generally
used for scanning pages out of a book, or paper that is out of the feeding specification of
the ADF. Also used to scan a small volume of documents by manual operation.
GL-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Gamma
A unit of changes of images' brightness. It is expressed as a function of the electric input
power to devices (scanner, display, etc.) and an image's brightness. If the gamma rate is
larger than 1, the brightness of an image increases and vice versa. In order to adjust the
brithtness of an image close to the orignal, generally the gamma value is set to 1.
Gray scale
A method for realizing the gradation from black to white on the scanned image. For
example, when scanning monochrome documents, the computer recognizes the docu-
ments as sets of black and white dots. In the Gray scale method, each dot contains data
regarding density of black. The original gradation of the documents is realized as the
gradation of the density data.
Halftone processing
Any method used to reproduce a photograph which includes a shade as an image com-
posed of dots, namely, a binary image. Dithering and error diffusion processing are
examples of halftone processing.
Image emphasis
Density is decreased for lighter but not completely white areas adjacent to black areas.
Weakening this emphasis eliminates spot noise or produces softened images.
Image processing
An image is scanned with specified parameters.
Interface
The connection that allows communication from the computer to the scanner.
Inversion (Reverse-image reading)
In reverse-image reading, data is changed from black to white and vice versa.
IPC preset mode
While reading binary images, it is necessary to set the scanner according to the quality
of the sheet to be read. In this mode, these settings can be performed in advance by cor-
responding each setting to a pattern number.
fi-4220C2 Image Scanner Operator’s Guide
GL-5
Download from Www.Somanuals.com. All Manuals Search And Download.
ISIS (Image Scanner Interface Specification)
A standard of API (Application Program Interface) or protocol for imaging devices (scan-
ners, digital cameras, etc.) developed by Pixel Translations, a division of Captiva Soft-
ware. In order to use imaging devices designed on the ISIS standard, it is necessary to
install the driver software of the same standard.
Jaggy images
Images that have sharp projections or irregular shape on their edges.
Job separation sheet
A sheet inserted between documents in a batch for separating different jobs.
Landscape
A document is transported and read with the Short side parallel to the moving direction.
Landscape orientation
A document is transported and scanned with the long side vertical to the moving direc-
tion.
Letter size
A standard paper size used in the U.S.A. and other countries. Paper size is 8-1/2 x 11
inches.
Linedrawing mode
Selecting linedrawing mode makes threshold and contrast settings effective but prevents
brightness from being set. The specified threshold value determines whether black or
white pixels are scanned. Line drawing mode is therefore appropriate for scanning text
and line art images.
Multi feed detection
A scanner function which detects accidental feeding of multiple sheets into the ADF. This
can be set as both enabled/disabled.
Mirror image
The read image is symmetrically flipped to produce a mirror image of the original
detected in the main scanning direction.
GL-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Moire Patterns
Recurrent patterns on scanned images caused by incorrect settings of angles.
Noise removal
Isolated noise from an image appearing as black spots in white areas and voids in black
areas is removed to improve image quality.
Removes particles from the document image. Common particles include toner and fax
particles. Noise reduction works via an algorithm that removes pixels up to 5 x 5 dots
appart. A dot is 1/400 inch. A particle can be distinguished from a character as it is not
connected to another dot within 5 pixels.
OCR (optical character recognition)
Devices or technologies for identifying characters on documents and converting them
into text data that can be manipulated. The documents are checked by light and the dif-
ferences of light reflection are recognized as character shapes.
Operator panel
A panel consists of indicators and buttons. The operator panel is used to control scanner
operations such as, selecting features, and changing settings.
Optical sensor
A type of sensor for detecting multi feeding by light transmission. It also detects multi
feeding by recognizing differences in length of documents.
Outline extraction
The boundary between black and white areas is traced and the outline extracted for
closed areas.
Pad ASSY (Pad Assembly)
This part is used to separate a sheet of paper from a batch before feeding documents
into the ADF. This assembly is made out of rubber.
Photograph mode (White level follower OFF)
Selecting photograph mode makes brightness and contrast settings effective but pre-
vents the threshold from being set. With photograph mode, the darkness of image corre-
sponds to the black-pixel density, making it suitable in scanning images such as
photographs having gradations.
fi-4220C2 Image Scanner Operator’s Guide
GL-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Pick roller
Roller(s) that picks the page from the batch of paper in the paper chute and feed it into
the ADF.
Pick start time
The period from the manual insertion of the document until picking starts after the docu-
ment passes the hopper empty sensor.
Pixel (Picture Element)
The tiny dots that make up a scanned image.
Portrait
Orientation of documents or images. Documents/images are set or displayed vertically.
Portrait orientation
A document is transported and read with the long side parallel to the moving direction.
Resolution
The measure of the details or grain of images displayed on a computer screen. As a met-
ric of the resolution, dpi is customarily used.
SCSI (Small Computer System Interface)
An abbreviation for "Small Computer System Interface". SCSI is a standard for inter-
faces, used to connect devices such as hard disks, scanners, etc. Up to seven devices
can be connected through this interface (daisy chain). The data transfer rates are differ-
ent between "Fast SCSI" (Max. 10MB/sec.) and "Wide SCSI" (Max. 20MB/sec.).
SCSI-ID
Used to specify a particular SCSI device when the initiator selects a target or the target
reconnects to the initiator.
Separation roller
A roller that separates the sheets of paper from each other.
Simplex reading mode
A mode for scanning only the front side of the document.
GL-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Smoothing
A process that eliminates "jaggies" from slanted lines and curves. Irregular convexities
are deleted and irregular concavities filled in. This is useful in OCR applications, for
example.
Storage temperature/humidity
The temperature and humidity levels necessary for proper storage of the scanner.
Temporary Error
An error that can be fixed by the operator.
Terminator
Devices with a SCSI interface can be daisy-chained. A resistor that includes terminal cir-
cuits needs to be placed at both ends of the SCSI chain when devices are daisy-
chained. If a device (such as a scanner) is the last device in a chain, leaving an interface
connector unused, a Terminator therefore must be attached to provide those terminal cir-
cits.
Third Party Interface
Used to install optional board provided by Fujitsu or interface board manufactured by a
third party.
Threshold
A value used as a metric for judging a color as black or white. For scanning an image
with gray gradation, this value must be defined. The threshold setting determines which
pixels are converted to black and which will become white.
TUV
"An institution that controls products for conformity with various standars of security,
usability and environmental matters. "
TWAIN (Technology Without Any Interesting Name)
A standard for API (Application Program Interface) or protocol for imaging devices (scan-
ners, digital cameras, etc.) developed by TWAIN Working Group. In order to use devices
that comply with this standard, it is necessary to install driver software based on the
same standard.
fi-4220C2 Image Scanner Operator’s Guide
GL-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Ultrasonic sensor
A type of sensor for detecting multi feeding by ultrasonic sound. Scanners detect multi
feeding by recognizing differences in the amount of ultrasonic waves that penetrates the
documents.
USB (Universal Serial Bus)
An abbreviation for "Universal Serial Bus". A standard for interfaces used to connect
devices such as key boards, scanners, etc. Up to 127 devices can be connected through
this interface. USB devices can be plugged/unplugged without turning off their power.
Data transfer rates are different between the "Low speed mode" (1.5Mbps) and "High
speed mode" (Max. 12Mbps).
White level follower
A function to correct the difference between white colors in unbleached paper (e.g. wood
containing paper, etc.) and in scanned images.
White Reference Stripe
The white part located in the ADF that defines the lightest area in an image, causing all
other areas to be adjusted accordingly.
GL-10
Download from Www.Somanuals.com. All Manuals Search And Download.
M
O
P
Setting Window for FUJITSU TWAIN32
R
Reset
S
IN-2
Download from Www.Somanuals.com. All Manuals Search And Download.
T
TROUBLESHOOTING ............................ 73
W
fi-4220C2 Image Scanner Operator’s Guide
IN-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
fi-4220C2 Image Scanner Operator’s Guide
P3PC-E927-01EN
Date of issuance: July, 2004
Issuance responsibility: PFU LIMITED
z Copying of the contents of this manual in whole or in part and
copying of the scanner application is forbidden under the copyright
law.
z The contents of this manual are subject to change without notice.
z PFU LIMITED. is not liable whatsoever for any damages resulting
from use of this scanner and procedures described in this manual,
profit due to defects, and any claims by a third party.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Eureka Air Compressor PBL SMC 10 NR User Manual
Eureka Vacuum Cleaner 2940 2969 Series User Manual
Extron electronic Stereo Receiver DVI DL 201 Rx User Manual
Fellowes Paper Shredder P 58Cs User Manual
Frigidaire Furnace KG7 User Manual
Frigidaire Microwave Oven FGMV175QB User Manual
Fujitsu Network Card PCI GigabitEthernet 30 User Manual
Garland Range C0836 12 User Manual
Gefen Home Theater System EXT COMPAUD 44424 User Manual
GE Water Heater GEH50DEEDXX User Manual