BATTERY DRIVE, MICRO LINE THERMAL PRINTER
3” TYPE MECHANISM AND INTERFACE BOARD
FTP-633MCL400/FTP-623DCL002
■ OVERVIEW
This battery driven, micro line thermal printer offers high speed
printing for 3-inch wide paper (70 mm). It is suitable for portable
equipment that requires compact, lightweight components.
In addition to the interface board, a driving LSI (MCU + Gate
Array) is also available.
■ HIGHLIGHTS
• Driven by batteries (direct connect between thermal
head and batteries)
FTP-633MCL400
It can be driven by a broad range of voltages (4.2 to 8.5 V) of
NiCd or Nickel-Hydrogen by using Fujitsu Components'
unique head drive control system. The battery pack can be
connected directly to the print head without a voltage
regulator. Also, a lithium-ion battery can be applied.
• High speed printing
It can print at approximately 24 character lines/s (460
dotlines/s = 60 mm/s).
• Compact and lightweight
It has a light weight of approximately 84 g.
FTP-623CU001, FTP-633GA101
• Low power consumption
The peak current for head driving is approximately 3.0 A.
• Selectable paper paths
Front, rear and top paper insertion paths can be used.
• Paper auto loading function
Paper feeding is enabled by operating the head up lever.
• Variety of suitable paper
This model is capable of printing on a variety of papers,
including 1-ply roll paper, 2-ply paper (TCC and roll), labels,
and long-life paper.
FTP-623DCL002
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
(Continued)
Item
Specifications
4.2 to 8.5 VDC (4 or 5 Ni-Cd or Ni-MH batteries, equivalent to 2 Li-ion)
Approximately 3.0 A (peak value, 7.2 V, 100% printing ratio)
For print head
Operating
voltage
4.2 to 8.5 VDC (4 or 5 Ni-Cd or Ni-MH batteries, equivalent to 2 Li-ion)
Average 0.7 A or less
For motor
For logic
5 VDC ± 5%, 0.15 A
Weight
Mechanism: approximately 84 g. Interface board: approximately 60 g
85 (W) × 49 (D) × 20 (H) mm (excluding knob, lever, and flexible PC board)
108 (W) × 91 (D) × 18 (H) mm
Printer mechanism Dimensions
Interface board
Dimensions
Pulse durability : 1 × 108 pulse/dot (using Fujitsu Takamisawa's standard
driving method)
Thermal head life
Wear resistance: 50 km (at 25% printing ratio)
Operating temperature
Operating humidity
Storage temperature
Storage humidity
Head temperature
Paper out/Mark detect
Voltage
+5 to +40°C*3
Environmental
conditions
20 to 85% RH (no condensation)
–20 to +60°C (excluding paper)
5 to 95% RH (no condensation)
By thermistor
Detection
By photointerrupter (command set)
By micro controller
Head-up
By microswitch
+0
Paper width
70 mm
–1
Recommended thermal sensitive paper
1 ply (roll) : FTP-030PG021
2 ply (TCC) : FTP-030P8021
Long life (roll) : FTP-030PR202
*1: Character composition for single density reduced mode is the same as for single density standard mode.
*2: The data to be printed is automatically read out by the printer driver equipment memory (host system frame
memory). The communication is parameter transfer.
*3: Temperature range for guaranteed printing density. It can be operated in the range of 0 to +40°C.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
■ DIMENSIONS
Printer mechanism
FTP-633MCL400
74.5
3.9
6.1
12.5
40
20
(3)
(1)
3
5
Paper center
85
2
2.3
1.7
12 (14)
(2)
Paper out
angle
(1): Head down
(2): Paper feed
(3): Head up lock
30
(Photo interrupter)
Unit: mm
Photo interrupter
70.2 (Paper insertion)
Front and top insertion type
FTP-633MCL402
74.5
12.5
3.9
6.1
40
20
(3)
(1)
3
5
1.7
3.1
Paper center
85
2
12 (14)
(2)
Photo
interrupter
Paper out
angle
(Photo
interrupter)
(1): Head down
(2): Paper feed
(3): Head up lock
30
(Photo interrupter)
Unit: mm
Rear insertion type
Photo interrupter
70.2 (Paper insertion)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
Interface board
108.0
102.9
69.8
5.1
CN5
ø3.6
CN4
CN8
CN7
CN6
CN2
CN1
5.1
16.5
73.7
102.9
Height of devices side
Height of solder side
Unit: mm
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
■ INTERFACE
1. Centronics standard
(1) Connector
Connector part number
: FCN-215Q030-G/0 (Fujitsu Components) or equivalent
Mating connector part number : FCN-217Q030-G/0 (Fujitsu Components) or equivalent
FCN-214Q030-G/0 (Fujitsu Components) or equivalent
FCN-215Q030-G/0 (Fujitsu Components) or equivalent
(2) Connector pin assignment
No.
1
Signal
PRSTB
I/O
Contents
Data strobe
No.
2
Signal
I/O
—
—
—
—
—
—
—
—
—
—
—
—
I
Contents
I
I
PRSTB-RET
PRDT0-RET
PRDT1-RET
PRDT2-RET
PRDT3-RET
PRDT4-RET
PRDT5-RET
PRDT6-RET
PRDT7-RET
ACKNLG-RET
BUSY-RET
INPRM-RET
INPRM
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Reset
3
PRDT0
PRDT1
PRDT2
PRDT3
PRDT4
PRDT5
PRDT6
PRDT7
ACKNLG
BUSY
Data 0
4
5
I
Data 1
6
7
I
Data 2
8
9
I
Data 3
10
12
14
16
18
20
22
24
26
28
30
11
13
15
17
19
21
23
25
27
I
Data 4
I
Data 5
I
Data 6
I
Data 7
O
O
O
I
Data input acknowledge
Busy
RINF2
SLCTIN
RINF1
ATF
Printer status
Printer select
Printer status
Paper feed request
O
I
RINF3
O
Printer status
29
GND
—
Logic GND
Notes:
• Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(3) Connector pin number
(4) Data input signal timing
FCN-215Q030-G/0 (Fujitsu Components) or
PRDT0~7
equivalent
3
t1
t3
PRSTB
BUSY
1
29
t2
t4
ACKNLG
t5
Data set time
:t1≥0.5 µsec
:t2≥0.5 µsec
:t3≥0.5 µsec
:t4≤0.5 µsec
:t5=1.0~1.5 µsec
PRSTB pulse width
Data hold time
PRSTB to BUSY= “H”
ACKNLG pulse time
2
30
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
2. Bus interface
(1) Connector
Connector part number
: FCN-215Q040-G/0 (Fujitsu Components) or equivalent
Mating connector part number : FCN-217J040-G/0 (Fujitsu Components) or equivalent
: FCN-214J040-G/0 (Fujitsu Components) or equivalent
: FCN-215J040-G/0 (Fujitsu Components) or equivalent
(2) Connector pin assignment
No.
1
Signal
ALE
I/O
O
—
—
—
O
I
Contents
Address latch
No.
2
Signal
BRD
I/O
—
—
—
O
Contents
Data read
3
BWR
Data write
4
READY
HRQ
Data access ready
User hold request input
System clock
5
HACK
MCRC
PCPAK1
PCPSD1
RST
Hold acknowledge
Power-down (not used)
6
7
8
CLK
9
Common RAM reading completion 10 ATF
I
Automatic paper loading
Printer operating
Ground
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Notes:
Common RAM reading request
Hard reset
12 PRON
14 GND
16 DB01
18 DB03
20 DB05
22 DB07
24 AB09
26 AB11
28 AB13
30 AB15
32 AB17
34 AB19
36 AB21
38 AB23
40 INPRM
O
I
—
DB00
DB02
DB04
DB06
AB08
AB10
AB12
AB14
AB16
AB18
AB20
AB22
RAM2
I/O External address/Data bus 0
I/O External address/Data bus 2
I/O External address/Data bus 4
I/O External address/Data bus 6
I/O External address/Data bus 1
I/O External address/Data bus 3
I/O External address/Data bus 5
I/O External address/Data bus 7
O
O
O
O
O
O
O
O
O
External address bus 08
External address bus 10
External address bus 12
External address bus 14
External address bus 16
External address bus 18
External address bus 20
External address bus 22
Common RAM access
O
O
O
O
O
O
O
O
I
External address bus 09
External address bus 11
External address bus 13
External address bus 15
External address bus 17
External address bus 19
External address bus 21
External address bus 23
Reset
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface bpard side.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
■ CONNECTOR PIN ASSIGNMENT
1. Connector for logic power supply (CN1)
Part number
: B4B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side
Mating connector part number : XHP-4 (J.S.T) or equivalent → Cable side
No.
1
Signal
I/O
—
Contents
No.
2
Signal
GND
I/O
—
Contents
VCC
Power supply for logic (+5V)
Logic ground
2. Connector for thermal head and motor power supply (CN2)
Part number
: B6B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side
Mating connector part number : XHP-6 (J.S.T) or equivalent → Cable side
No.
1
Signal
BAT
I/O
—
—
—
Contents
No.
2
Signal
BAT
I/O
—
—
—
Contents
Power supply for head/motor
Head/motor ground
Power supply for head/motor
Power supply for head/motor
Head/motor ground
3
BAT
4
GND
GND
5
GND
6
Head/motor ground
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
3. Connector for thermal head drive (CN7)
Part number
: 52030-2610 (Molex) or equivalent → P.C.B side
No.
Signal
BAT
I/O
—
—
O
Contents
Power for head
No.
2
Signal
BAT
I/O
—
—
O
Contents
Power for head
1
3
GND
Head ground
4
GND
LAT
Head ground
5
HD2
Print data output
6
Printing data latch
Printing transmitting clock
Printing enable
7
HDV
O
Power for logic
8
HCLK
O
9
ENB8 *1, 2
ENB6
VREF
O
Printing enable
10 ENB7 *1, 2
12 ENB5
14 TMP
—
O
11
13
15
17
19
21
23
25
Notes:
O
Printing enable
Printing enable
O
Power for thermistor
Connected with No. 17
Connected with No. 15
Not used (pulled-up by resistor)
Automatic paper loading
Printing enable
O
Temperature detection
Power for logic
3
*
—
—
—
O
16 HDV
O
3
4
*
18
*
—
O
Head rank specify (not used)
Printing enable
4
*
20 ENB4
22 ENB2
24 GND
26 BAT
ENB3
ENB1
GND
O
Printing enable
O
—
—
Paper-out detection
Power for head
—
Printing enable
*1: Mechanism selection signal and the printing enable signal for 3” mechanism.
*2: Not used at the combination with 2” mechanism.
*3: At the mechanism side, this pin number is for the printing data 2.
Since this pin number is used for the printing data 1 at the inter face board, the No. 15 and No. 17 pins are
connected.
*4: This signal is used for the adjustment of printing duty depending upon the rank of thermal head resistor. Not
used at this interface board.
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
4. Connector for abnormal head temperature detection (CN6)
Part number
: B3B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side
Mating connector part number : XHP-3 (J.S.T) or equivalent → Cable side
No.
1
Signal
TMPER
GND
I/O
O
Contents
Abnormal head temperature detection
Logic ground
No.
2
Signal
N.C.
I/O
—
Contents
Not connected
3
—
Note: This signal detects abnormal head temperature.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
5. Connector for stepping motor drive (CN8)
Part number
: B10B-ZR (J.S.T) or equivalent → P.C.B side
Mating connector part number : ZHR-10 (J.S.T) → Mechanism side
No.
1
Signal
HUP
I/O
I
Contents
Head up detection
No.
2
Signal
I/O
—
—
I
Contents
Power for switch
VCC
3
PINCH
SLED
I
Paper auto loading detection
Power for diode cathode
4
SDV
Power for photointerrupter
Paper out detection
5
—
O
O
6
PES
7
MT/B0
MT/A0
Stepping motor coil excitation (B)
8
MT/B0
O
Stepping motor coil excitation (B)
Stepping motor coil excitation (A)
9
Stepping motor coil excitation (A) 10 MT/A0
O
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
■ PRINTING COMMANDS (CENTRONICS STANDARD INTERFACE)
Name
Command
Contents
Carriage return
LF, CR
SO
Prints buffer data and return the line.
Sets the double width character.
Double width print set
Power-down mode set
DC2, DC3
Reduces the power consumption during standing
by.
Double width print reset
ESC sequence entry
DC4
ESC
Resets the double with character.
Indicates the start of an escape sequence formed
by this code plus subsequent commands.
Line space set
ESC A + n
Sets the line space length in 2 × (0 to 255 dot
lines).
Paper feed set in normal direction
Bit image print set
ESC B + n
Sets the paper feed in normal direction.
(Feeding range: 2 × (0 to 255 dot lines))
ESC K +n1+n2+n3
Sets the bit image printing in single or double
density mode.
International character set
Download character register
ESC R+n
Selects the international characters.
ESC &+n1+n2+~
Registers the download characters of 12 × 6 or 16
× 8 dots.
Printing quality set
Printing density set
ESC Q+n+SP*+~
ESC Q+n+!+A
Sets the printing quality conforming to used paper.
Sets the printing density mode.
(Single density standard, reduced or double
density)
Paper feed set in reverse direction
Character grade set
ESC j+n
ESC x+n
Sets the paper feed in reverse direction.
(Feeding range: 2 × (1 to 255 dot lines))
Sets the character grade in standard or high
grade.
Special character print set
ESC ¥+n
ESC 1+n
Prints the special character.
Start position set for bit-image printing
Sets the print start position of bit-image printing in
left end.
Detecting function set
Mark detection
ESC 9+n
ESC FF
Sets the detecting function.
Feeds the paper to the marking position.
Sets the line feed length after mark detection.
Line feed length set after mark detection ESC w+n
Automatic paper loading length set
Automatic printing speed set
Printer initialization
ESC EM+n
ESC s+n
ESC @
Sets paper feeding length for automatic paper
loading.
Sets the function mode in the automatic printing
speed set.
Initializes the printer MPU.
Notes:
*: “SP” means the space code (20H).
Bus interface uses different commands.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP-633MCL400/FTP-623DCL002
■ OPTIONS
1. Cable
Name
For Centronics
For Bus I/F
Part number
Cable length
500 mm
500 mm
300 mm
300 mm
300 mm
FTP-621Y202
FTP-621Y203
FTP-621Y401
FTP-621Y601
FTP-621Y204
Interface cable
Power supply cable (A): for logic motor
Power supply cable (B): for thermal head
Head abnormal temperature detection cable
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
Fujitsu Component Limited
Gotanda-Chuo Building
2132 WV Hoofddorp
Netherlands
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components
International
Headquarter
Offices
Tel: (31-23) 5560910
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Fax: (31-23) 5560950
Email: [email protected]
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 375-8560
Fax: (1-408) 745-4970
Fax: (65) 273-3021
Email: [email protected]
Email: [email protected]
© 2001 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 09/2001
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|