S Series.book Page 1 Thursday, February 19, 2004 4:52 PM
C o p y r i g h t
Norton AntiVirus is a registered trademark of Symantec
Corporation.
Copyright
BayManager is a registered trademark of Softex, Inc.
Fujitsu Computer Systems Corporation has made every
effort to ensure the accuracy and completeness of this
document; however, as ongoing development efforts are
continually improving the capabilities of our products,
we cannot guarantee the accuracy of the contents of this
document. We disclaim liability for errors, omissions, or
future changes.
The DVD player found in some models of the LifeBook
notebook incorporates copyright protection technology
that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights users. Use of
this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless authorized by
Macrovision Corporation. Reverse engineering or disas-
sembly is prohibited.
Fujitsu, the Fujitsu logo, and LifeBook are registered
trademarks of Fujitsu Limited.
The following are registered trademarks of IBM
Corporation: IBM, IBM PC AT, IBM PS/2.
Dolby Headphone manufactured under license from
Dolby Laboratories. Dolby, Pro Logic, and the double-D
symbol are trademarks of Dolby Laboratories. Copy-
rights 1992-1999 Dolby Laboratories. All rights reserved.
The following are registered trademarks of Microsoft
Corporation: MS, MS-DOS, Windows.
PCMCIA is a trademark of the Personal Computer
Memory Card International Association.
All other trademarks mentioned herein are the property
of their respective owners.
Earthlink is a registered trademark of EarthLink
Network, Inc.
Warning
Intel and Pentium are registered trademarks of Intel
Corporation or its subsidiaries in the United States and
other countries.
Handling the cord on this product will expose you
to lead, a chemical known to the State of
California to cause birth defects or other
reproductive harm.
The Bluetooth trademark is owned by Bluetooth SIG,
Inc., USA.
Wash hands after handling.
Adobe Acrobat Reader is a registered trademark of
Adobe Systems, Inc.
© Copyright 2004 Fujitsu Computer Systems Corpora-
tion. All rights reserved. No part of this publication may
be copied, reproduced, or translated, without prior
written consent of Fujitsu. No part of this publication
may be stored or transmitted in any electronic form
without the written consent of Fujitsu.
Netscape 7.0 is a registered trademark of Netscape
Communications Corporation.
PowerQuest and Drive Image are registered trademarks
of PowerQuest Corporation.
B5FH-9991-02EN-00
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name:
Fujitsu Computer Systems Corporation
Address:
1250 E. Arques Avenue, M/S 122
Sunnyvale, CA 94085
Telephone:
(408) 746-6000
Declares that product:
Base Model Configurations:
LifeBook S7010 notebook
LifeBook S7010D notebook
Complies with Part 15 of the FCC Rules.
This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:
(1) This device must not be allowed to cause harmful interference, (2) This device must accept any
interference received, including interference that may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 3 Thursday, February 19, 2004 4:52 PM
Ta b l e o f C o n t e n t s
®
Fujitsu LifeBook S7000 Notebook
Table of Contents
Keyboard
1
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . .13
Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . .13
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . .14
PREFACE
Preface
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . .1
Fujitsu Contact Information . . . . . . . . . . . . . . . . .1
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . .1
Touchpad Pointing Device
Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . .15
Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Touchpad Control Adjustment . . . . . . . . . . . . . .16
Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Optional Quick Point Feature. . . . . . . . . . . . . . .16
2
GETTING TO KNOW
YOUR LIFEBOOK
Volume Control
Controlling the Volume . . . . . . . . . . . . . . . . . . .17
Overview
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Flexible Bay Devices
Removing and Installing Modular Devices . . . . .18
Locating the Controls
and Connectors
Top and Front Components . . . . . . . . . . . . . . . . .6
Left-Side Panel Components . . . . . . . . . . . . . . . .7
Right-Side Panel Components . . . . . . . . . . . . . . .8
Back Panel Components. . . . . . . . . . . . . . . . . . . .9
Bottom Components . . . . . . . . . . . . . . . . . . . . .10
LifeBook Security/Application Panel
Setting up Your LifeBook Security Panel . . . . . . .20
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Operating Your LifeBook Security/
Application Panel. . . . . . . . . . . . . . . . . . . . .21
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Uninstalling the Security Panel Application . . . . .21
Status Indicator Panel
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . .11
AC Adapter Indicator . . . . . . . . . . . . . . . . . . . . .11
Battery Level Indicators . . . . . . . . . . . . . . . . . . .11
Battery Charging Indicators . . . . . . . . . . . . . . . .12
DVD/CD-RW/CD-ROM Drive Access Indicator .12
Launching Applications with
the Security/Application Panel . . . . . . . . . . .22
3
Hard Drive or Removable
Media Drive Access Indicator. . . . . . . . . . . .12
GETTING STARTED
PC Card Access Indicators . . . . . . . . . . . . . . . . .12
NumLk Indicator. . . . . . . . . . . . . . . . . . . . . . . . .12
CapsLock Indicator. . . . . . . . . . . . . . . . . . . . . . .12
ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .12
Security Indicator . . . . . . . . . . . . . . . . . . . . . . . .12
Power Sources
Connecting the Power Adapters. . . . . . . . . . . . .27
Display Panel
Opening the Display Panel . . . . . . . . . . . . . . . . .28
Adjusting Display Panel Brightness . . . . . . . . . . .28
Closing the Display Panel . . . . . . . . . . . . . . . . . .28
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 4 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Starting Your LifeBook Notebook
Port Replicator
Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Boot Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . 29
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . 29
Booting the System . . . . . . . . . . . . . . . . . . . . . . 30
Windows Product Activation . . . . . . . . . . . . . . . 30
Registering Your LifeBook Notebook . . . . . . . . . 31
Installing Click Me! . . . . . . . . . . . . . . . . . . . . . . 31
Back Panel Components . . . . . . . . . . . . . . . . . . 49
Front Panel Components . . . . . . . . . . . . . . . . . . 50
Attaching the Port Replicator. . . . . . . . . . . . . . . 50
Locking the Port Replicator . . . . . . . . . . . . . . . . 51
Detaching the Port Replicator . . . . . . . . . . . . . . 51
Device Ports
Modem (RJ-11) Telephone Jack. . . . . . . . . . . . . 52
Internal LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . 52
Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
PS/2 Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Universal Serial Bus Ports. . . . . . . . . . . . . . . . . . 53
Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Stereo Line-In Jack. . . . . . . . . . . . . . . . . . . . . . . 54
IEEE 1394 Port. . . . . . . . . . . . . . . . . . . . . . . . . . 54
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 54
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 54
External Monitor Port . . . . . . . . . . . . . . . . . . . . 54
Power Management
Power/Suspend/Resume Button . . . . . . . . . . . . 32
Suspend Mode. . . . . . . . . . . . . . . . . . . . . . . . . . 32
Hibernation (Save-to-Disk) Feature . . . . . . . . . . 33
Display Timeout. . . . . . . . . . . . . . . . . . . . . . . . . 33
Hard Disk Timeout. . . . . . . . . . . . . . . . . . . . . . . 33
Windows Power Management. . . . . . . . . . . . . . 33
Restarting the System . . . . . . . . . . . . . . . . . . . . 33
Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4
USER-INSTALLABLE FEATURES
5
Lithium ion Battery
Recharging the Batteries . . . . . . . . . . . . . . . . . . 37
TROUBLESHOOTING
Replacing the Battery. . . . . . . . . . . . . . . . . . . . . 38
Troubleshooting
Optical Drive
Identifying the Problem . . . . . . . . . . . . . . . . . . . 57
Specific Problems. . . . . . . . . . . . . . . . . . . . . . . . 57
Troubleshooting Table. . . . . . . . . . . . . . . . . . . . 58
Power On Self Test Messages . . . . . . . . . . . . . . 66
Emergency media Player Drive Tray Release . . . 67
Modem Result Codes . . . . . . . . . . . . . . . . . . . . 67
Restoring Your Pre-installed Software . . . . . . . . 68
Drive Image Special Edition (DISE). . . . . . . . . . . 68
Automatically Downloading Driver Updates . . . 69
Media Player Software. . . . . . . . . . . . . . . . . . . . 39
Loading Media on Your Drive . . . . . . . . . . . . . . 40
Removing Media . . . . . . . . . . . . . . . . . . . . . . . . 40
Using the Media Player Software. . . . . . . . . . . . 40
Using Dolby™ Headphone . . . . . . . . . . . . . . . . 41
Using Media Player on Battery Power . . . . . . . . 41
External USB Floppy Disk Drive
Loading a Disk. . . . . . . . . . . . . . . . . . . . . . . . . . 44
Ejecting a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Preparing a Disk for Use . . . . . . . . . . . . . . . . . . 44
6
PC Cards
Installing PC Cards. . . . . . . . . . . . . . . . . . . . . . . 45
Removing PC Cards. . . . . . . . . . . . . . . . . . . . . . 45
Smart Card Reader. . . . . . . . . . . . . . . . . . . . . . . 46
CARING FOR YOUR LIFEBOOK
Care and Maintenance
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Floppy Disks and Drives. . . . . . . . . . . . . . . . . . . 74
Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Memory Upgrade Module
Installing Memory Upgrade Modules. . . . . . . . . 47
To Remove a Memory Upgrade Module . . . . . . 47
Checking the Memory Capacity. . . . . . . . . . . . . 48
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 5 Thursday, February 19, 2004 4:52 PM
Ta b l e o f C o n t e n t s
Connection using
7
Wireless Zero Configuration Tool
Flow of operations . . . . . . . . . . . . . . . . . . . . . .101
Preparation for wireless LAN connection . . . . .101
Connection to the network. . . . . . . . . . . . . . . .103
SYSTEM SPECIFICATIONS
Specifications
Configuration Label . . . . . . . . . . . . . . . . . . . . . .79
Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . .79
Chipset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Mass Storage Device Options. . . . . . . . . . . . . . .79
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Dimensions and Weight . . . . . . . . . . . . . . . . . . .81
Environmental Requirements . . . . . . . . . . . . . . .81
Popular Accessories . . . . . . . . . . . . . . . . . . . . . .81
Pre-Installed Software . . . . . . . . . . . . . . . . . . . .81
Learning About Your Software . . . . . . . . . . . . . .81
Connection using
Atheros Client Utility
Flow of operations . . . . . . . . . . . . . . . . . . . . . .106
Preparation for wireless LAN connection . . . . .106
Connection to the network. . . . . . . . . . . . . . . .107
Other settings
Setting of power-saving function . . . . . . . . . . .110
Troubleshooting the WLAN
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .111
Wireless LAN Glossary
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
IP address information
Additional Information
Specifications
Specification. . . . . . . . . . . . . . . . . . . . . . . . . . .117
8
Using the Bluetooth Device
What is Bluetooth. . . . . . . . . . . . . . . . . . . . . . .118
Where to Find Information
About Bluetooth . . . . . . . . . . . . . . . . . . . . . . .118
GLOSSARY/REGULATORY
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Regulatory Information . . . . . . . . . . . . . . . . . . .91
INDEX
APPENDIX:
WIRELESS LAN USER’S GUIDE
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Before Using the Wireless LAN
For better communications. . . . . . . . . . . . . . . . .99
Stopping transmission. . . . . . . . . . . . . . . . . . . .100
Starting Transmission . . . . . . . . . . . . . . . . . . . .100
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 6 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 1 Thursday, February 19, 2004 4:52 PM
1
Preface
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 2 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 1 Thursday, February 19, 2004 4:52 PM
P r e f a c e
The caution icon highlights information
that is important to the safe operation of
your computer, or to the integrity of your
files. Please read all caution information
carefully.
Preface
ABOUT THIS GUIDE
The LifeBook S7000 notebook from Fujitsu is a powerful
computer. It is powered by an Intel Pentium M micro-
processor, has a built-in TFT XGA color display, a
number of possible configurations, and brings the
computing power of desktop personal computers (PCs)
to a portable environment.
The warning icon highlights information
that can be hazardous to either you, your
LifeBook notebook, or your files. Please
read all warning information carefully.
This manual explains how to operate your LifeBook
notebook’s hardware and built-in system software. Your
notebook is compatible with the IBM® PC AT.
FUJITSU CONTACT INFORMATION
Service and Support
You can contact Fujitsu Service and Support in the
following ways:
Your computer comes with Microsoft Windows® XP
Home, Windows XP Professional, or Windows 2000
Professional pre-installed. (See note below.)
■
■
■
Toll free: 1-800-8Fujitsu (1-800-838-5487)
E-mail: 8fujitsu@us.fujitsu.com
Web site: us.fujitsu.com/computers
If your system was delivered with
Windows 2000 as the operating system,
the Windows 2000 image is on the D:
partition, but the Restore Disc contains
Windows XP. If you decide to restore your
system from the Restore Disc, you will
overwrite Windows 2000 with the
Windows XP operating system. Please
refer to “Restoring Your Pre-installed
Software” on page 66.
Before you place the call, you should have the following
information ready so that the customer support
representative can provide you with the fastest possible
solution:
■
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Hardware configuration
Type of device connected, if any
■
■
■
■
The LifeBook S7000 notebook is a completely self-
contained unit with an active-matrix (TFT) color LCD
display. It has a powerful interface that enables it to
support a variety of optional features.
■
■
■
Fujitsu Online
Conventions Used in the Guide
You can go directly to the online Fujitsu Product catalog
for your LifeBook notebook by clicking on the LifeBook
Accessories Web site URL link located in the Service and
Support Software folder of the Windows Start menu.
Keyboard keys appear in brackets.
Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].
Pages with additional information about a specific topic
are cross-referenced within the text.
For example: (See page xx.)
You can also reach Fujitsu Service and Support online by
clicking on the Service and Support Web site URL link,
located in the Service and Support Software folder of the
Windows Start menu.
On screen buttons or menu items appear in bold
Example: Click OK to restart your LifeBook notebook.
DOS commands you enter appear in Courier type.
Example: Shutdown the computer?
You must have an active internet
connection to use the online URL links.
The information icon highlights
information that will enhance your
understanding of the subject material.
LIMITED WARRANTY
Your LifeBook notebook is backed by a Fujitsu Interna-
tional Limited Warranty. Check the service kit that came
with your notebook for the Limited Warranty period
and terms and conditions.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 2 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
2
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 3 Thursday, February 19, 2004 4:52 PM
2
Getting to Know
Your LifeBook Notebook
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 4 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
4
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 5 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Figure 2-1. Fujitsu LifeBook S7000 notebook
Depending on your system configuration, the following
optional items may be included with your system:
Overview
This section describes the components of your Fujitsu
LifeBook S7000 notebook. We strongly recommend that
you read it before using your notebook – even if you are
already familiar with notebook computers.
■
Modular 2nd bay battery
External USB floppy disk drive
■
Depending on your configuration, you may receive the
following application CDs:
UNPACKING
■
DVD Application CD
CD-RW Application CD
When you receive your LifeBook notebook, unpack it
carefully, and compare the parts you have received with
the items listed below.
■
Once you have checked and confirmed that your Life-
Book system is complete, read through the following
pages to learn about all of your notebook’s components.
For a pre-configured model you should have:
■
LifeBook S7000 notebook (Figure 2-1)
AC adapter with AC power cord (Figure 2-2)
Lithium ion Battery, pre-installed
Weight Saver
Phone/Modem (RJ-11) telephone cable
Driver and Application Restore (DAR) Disc
Getting Started Guide
User’s Guide (this document)
■
■
■
■
■
■
■
■
International Limited Warranty Brochure
Microsoft®-associated product materials
■
Figure 2-2 AC Adapter
Depending on your system configuration, one of the
following devices will be pre-installed in the Flexible
Bay:
■
Weight Saver
Modular Super-Multi DVD Drive
Modular DVD/CD-RW combo drive
Modular CD-ROM drive
■
■
■
5
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 6 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Display Panel
Status Indicator Panel
Stereo Speaker
Touchpad
LifeBook Security/
Application Panel
Pointing Device
Power/
Suspend/
Resume Button
Wireless
LAN/Bluetooth
On/Off Switch
Stereo Speaker
Left Button
Keyboard
Scroll Button
Quick Point
Cursor Control (optional)
Display Panel Latch
Right Button
Figure 2-3. LifeBook notebook with display open
Keyboard
Locating the Controls
and Connectors
A full-size keyboard with dedicated Windows keys. (See
Keyboard on page 13 for more information)
Touchpad Pointing Device
The Touchpad pointing device is a mouse-like cursor
control with three buttons: two mouse-like buttons, and
a scroll button. (See Touchpad Pointing Device on page 15
for more information)
TOP AND FRONT COMPONENTS
The following is a brief description of your LifeBook
notebook’s top and front components.
Display Panel
The display panel is a color LCD panel with back
Quick Point Cursor Control (optional)
The optional Quick Point control offers an additional
method for moving the cursor. (See Optional Quick
Point Feature on page 16 for more information)
lighting for the display of text and graphics.
LifeBook Security/Application Panel
The LifeBook Security/Application Panel provides
hardware security and one-touch application launch
capability. (See LifeBook Security/Application Panel on
page 20 for more information)
Display Panel Latch
The display panel latch locks and releases the display
panel.
Wireless LAN/Bluetooth On/Off Switch
The wireless LAN/Bluetooth on/off switch is used to
power on and off the optional WLAN and/or Bluetooth
device. Switching the device off when not in use will help
to extend battery life.
Power/Suspend/Resume Button
The Power/Suspend/Resume button allows you to
suspend notebook activity without powering off, resume
your LifeBook notebook from suspend mode, and
power on your notebook when it has been shut down
from Windows. (See Power/Suspend/Resume Button on
page 32 for more information)
Status Indicator Panel
The Status Indicator Panel displays symbols that corre-
spond with a specific component of your LifeBook note-
book. (See Status Indicator Panel on page 11 for more
information)
Stereo Speakers
The built-in dual speakers allow for stereo sound.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 7 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
External Monitor Port
(behind door)
IEEE 1394 Jack
Microphone Jack
PC Card Slots
Air Vents
Line In Jack Headphone Jack
PC Card Eject Button
DC Power Jack
Figure 2-4. LifeBook notebook left-side panel
LEFT-SIDE PANEL COMPONENTS
The following is a brief description of your LifeBook
notebook’s left-side components.
External Monitor Port
The external monitor port allows you to connect an
external monitor. (See External Monitor Port on page 52
for more information)
IEEE 1394 (4-pin) Jack
The 4-pin 1394 jack is used to connect between
your LifeBook and an IEEE 1394 peripheral such as a
digital video camera. (See IEEE 1394 Port on page 52 for
more information)
Microphone Jack
The microphone jack allows you to connect an external
mono microphone. (See Microphone Jack on page 52 for
more information)
PC Card Slot
The PC Card Slots allow you to install two Type I or
Type II PC Cards or one Type III PC Card. (See PC Cards
on page 43 for more information)
Stereo Line-in Jack
The stereo line-in jack allows you to connect an external
audio source. (See Stereo Line-In Jack on page 52 for more
information)
Headphone Jack
The headphone jack allows you to connect headphones
or powered external speakers. (See Headphone Jack on
page 52 for more information)
DC Power Jack
The DC power jack allows you to plug in the AC adapter
to power your LifeBook notebook and charge the
internal Lithium ion battery.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 8 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Flexible Bay
(CD-ROM/DVD/CD-RW drive/battery)
USB 2.0 Port
Modem (RJ-11) Jack
Flexible Bay
Eject Lever
Anti-Theft Lock Slot
Figure 2-5. LifeBook notebook right-side panel
Flexible Bay
RIGHT-SIDE PANEL COMPONENTS
The following is a brief description of your LifeBook
notebook’s right-side components.
The Flexible Bay can accommodate one of the following
devices. (See Flexible Bay Devices on page 18 for more
information)
Modem (RJ-11) Telephone Jack
■
■
■
■
■
■
Modular USB Floppy Disk Drive
Modular CD-ROM drive
Modular DVD/CD-RW combo drive
Modular Super-Multi DVD Drive
Modular Lithium ion battery
Weight Saver
The Modem (RJ-11) telephone jack is for attaching
a telephone line to the internal multinational 56K
modem. (See Modem (RJ-11) Telephone Jack on page 50
for more information)
The internal modem is not intended for
use with Digital PBX systems. Do not
connect the internal modem to a Digital
PBX as it may cause serious damage to the
internal modem or your entire notebook.
Consult your PBX manufacturer’s
Flexible Bay Eject Lever
The Flexible Bay eject lever releases the Flexible Bay
device.
USB 2.0 Port
documentation for details. Some hotels
have Digital PBX systems. Be sure to find
out BEFORE you connect your modem.
The USB 2.0 port allows you to connect Universal Serial
Bus devices. USB 2.0 transfers data at up to 480Mbps
and is backward-compatible with USB 1.1 devices,
which transfer data at up to 12Mbps. (See Universal
Serial Bus Ports on page 51 for more information)
The internal multinational modem is
designed to the ITU-T V.90 standard. Its
maximum speed of 53000bps is the
highest allowed by FCC, and its actual
connection rate depends on the line
conditions. The maximum speed is 33600
bps at upload.
Anti-theft Lock Slot
The anti-theft lock slot allows you to attach an optional
physical lock down device.
For additional information about the
multinational modem, refer to the Fujitsu
web site at: us.fujitsu.com/computers
8
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 9 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Infrared Port
USB 2.0 Ports
LAN (RJ-45) Jack
Figure 2-6. LifeBook notebook back panel
BACK PANEL COMPONENTS
Following is a brief description of your LifeBook note-
book’s back panel components.
Infrared Port
The fast IrDA compatible port allows you to communi-
cate with another IrDA compatible infrared device
without a cable. (See Infrared Port on page 51 for more
information)
USB 2.0 Ports
The USB 2.0 ports allow you to connect Universal Serial
Bus devices. USB 2.0 transfers data at up to 480Mbps
and is backward-compatible with USB 1.1 devices,
which transfer data at up to 12Mbps. (See Universal
Serial Bus Ports on page 51 for more information)
LAN (RJ-45) Jack
The internal LAN (RJ-45) jack is used for an internal
Gigabit (10Base-T/100Base-Tx/1000Base-T/Tx)
Ethernet LAN connection. (See Internal LAN (RJ-45)
Jack on page 50 for more information)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 10 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Lithium ion
Battery Bay
Port Replicator
Connector
Certificate of
Authenticity
(approximate
location)
Main Unit and
Configuration
Label
Memory Upgrade
Compartment
Hard Disk Drive/
Bluetooth
Compartment
Figure 2-7. LifeBook notebook bottom panel
Hard Disk Drive/Bluetooth Compartment
BOTTOM COMPONENTS
This compartment houses the system hard disk drive
and the optional Bluetooth device. (Note that the
optional wireless LAN device is located under the
keyboard). Under normal circumstances, it should not
be necessary to open this compartment.
The following is a brief description of your LifeBook
notebook’s bottom panel components.
Port Replicator Connector
This connector allows you to connect the optional Port
Replicator to your notebook.
Memory Upgrade Compartment
Your LifeBook notebook comes with high speed Double
Data Rate Synchronous Dynamic RAM (DDR SDRAM).
The memory upgrade compartment allows you to
expand the system memory capacity of your LifeBook
notebook, hence improving overall performance. (See
Memory Upgrade Module on page 45 for more informa-
tion)
Lithium ion Battery Bay
The battery bay contains the internal Lithium ion
battery. It can be opened for the removal of the battery
when stored over a long period of time or for swapping
a discharged battery with a charged Lithium ion battery.
(See Lithium ion Battery on page 37 for more information)
Main Unit and Configuration Label
The configuration label shows the model number and
other information about your LifeBook notebook. In
addition, the configuration portion of the label has the
serial number and manufacturer information that you
will need to give your support representative. It identi-
fies the exact version of various components of your
notebook.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 11 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
1
2
Power
Battery
Identifier
Hard Drive
Access
NumLk
ScrLk
Battery Charging
AC Adapter
Battery
Level
PC Card
Access
(PC Card Slot)
CapsLk
Media Player
Drive Access
Security
Figure 2-8. Status Indicator Panel
■
Off: Power is only coming from the batteries, and
you do not have an adapter connected.
Status Indicator Panel
The Status Indicator displays symbols that correspond
with a specific component of your Fujitsu LifeBook
notebook. These symbols tell you how each of those
components are operating. (Figure 2-8)
BATTERY LEVEL INDICATORS
The two Battery Level indicators state whether or not the
primary Lithium ion battery and/or the optional second
Lithium ion battery are installed (Battery 1 refers to the
primary Lithium ion battery, while Battery 2 refers to the
Flexible Bay optional second battery). In addition, this
symbol states how much charge is available within each
installed battery. The symbol will only be displayed for a
battery that is currently installed in your LifeBook note-
book. (Figure 2-9)
POWER INDICATOR
The Power indicator symbol states whether your system
is operational. It has several different states, each of
which tells you the mode your notebook is in.
■
Steady On: This means that there is power to your
LifeBook notebook and that it is ready for use.
Flashing: This means that your LifeBook notebook is
in Suspend mode.
Steady Off: This means that your system is either in
76%–100% Charging
76%–100%
■
■
Save-to-Disk mode, or that your LifeBook notebook
has been turned off.
51%–75%
If you are charging your battery, the Power indicator will
remain on even if your notebook is shut off. The Power
indicator will also remain on if you have either adapter
connected and are shut down from Windows.
26%–50%
11%–25%
Low Warning <11%
AC ADAPTER INDICATOR
Critical Low or
Dead Battery
The AC Adapter indicator states whether your notebook
is operating from the AC adapter, the Auto/Airline
adapter or the batteries. This icon has two different
states that can tell you what power source your LifeBook
notebook is using.
Shorted Battery
Figure 2-9 Battery Level Indicator
■
On: This means that either of the adapters are
currently in use.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 12 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
PC CARD ACCESS INDICATORS
The PC Card Access indicators display whether or not
your notebook is accessing a PC Card. The indicator will
flash if your software tries to access a PC Card even if
there is no card installed. (See PC Cards on page 43 for
more information)
A shorted battery is damaged and must be
replaced. (Figure 2-9)
BATTERY CHARGING INDICATORS
Located to the left of each of the Battery Level indicators
is a small arrow symbol. This symbol states whether that
specific battery is charging. This indicator will flash if
the battery is too hot or cold to charge.
NUMLK INDICATOR
The NumLk indicator states that the integral keyboard is
set in ten-key numeric keypad mode.
Batteries subjected to shocks, vibration or
extreme temperatures can be permanently
damaged.
CAPSLOCK INDICATOR
The CapsLock indicator states that your keyboard is set
to type in all capital letters.
DVD/CD-RW/CD-ROM DRIVE
ACCESS INDICATOR
SCRLK INDICATOR
The ScrLk indicator states that your scroll lock is active.
The DVD/CD-RW/CD-ROM Access indicator tells you
that the DVD/CD-RW/CD-ROM drive is being accessed.
If the Auto Insert Notification function is active, the
indicator will flash periodically when your system is
checking the DVD/CD-RW/CD-ROM drive. If the Auto
Insert Notification function is not active, the indicator
will only flash when you access the DVD/CD-RW/CD-
ROM drive. The default setting is the Auto Insert Notifi-
cation function active.
SECURITY INDICATOR
The Security Indicator flashes (if a password was set)
when the system resumes from Off or Standby modes.
You must enter the password that was set in the Security
Panel before your system will resume operation.
The DVD/CD-RW/CD-ROM Auto Insert
Notification function will periodically check
for a DVD/CD-RW/CD-ROM installed in
the drive, causing the DVD/CD-RW/CD-
ROM Access indicator to flash. The DVD/
CD-RW/CD-ROM Auto Insert Notification
function allows your system to
automatically start a DVD/CD-RW/CD-
ROM as soon as it is inserted in the drive
and the tray is closed. It will begin playing
an audio DVD/CD or will start an
application if the DVD/CD has an auto-
run file
HARD DRIVE OR REMOVABLE
MEDIA DRIVE ACCESS INDICATOR
The Hard Drive Access indicator states whether your
internal hard drive is being accessed.
The Hard Drive Access indicator does not
show which hard drive is being accessed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 13 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Function Keys
End
Home
Fn Key
Numeric Keypad
(surrounded by heavy line)
Start Key
Cursor Keys
Application Key
Figure 2-10 Keyboard
NUMERIC KEYPAD
Keyboard
Certain keys on the keyboard perform dual functions as
both standard character keys and numeric keypad keys.
NumLk can be activated by pressing the [NumLk] keys.
Turning off the NumLk feature is done the same way.
Once this feature is activated you can enter numerals 0
through 9, perform addition ( + ), subtraction ( - ),
multiplication ( * ), or division ( / ), and enter decimal
points ( . ) using the keys designated as ten-key function
keys. The keys in the numeric keypad are marked on the
front edge of the key to indicate their secondary functions.
(Figure 2-10)
USING THE KEYBOARD
Your Fujitsu LifeBook notebook has an integral 84-key
keyboard. The keys perform all the standard functions of
a 101-key keyboard, including the Windows keys and
other special function keys. This section describes the
following keys. (Figure 2-10)
■
Numeric keypad: Your notebook allows certain keys to
serve dual purposes, both as standard characters and
as numeric and mathematical keys. The ability to tog-
gle between the standard character and numerical keys
is controlled through the [NumLk] key.
WINDOWS KEYS
Your LifeBook notebook has two Windows keys,
consisting of a Start key and an Application key. The
Start key displays the Start menu. This button functions
the same as your onscreen Start menu button. The
Application key functions the same as your right mouse
button and displays shortcut menus for the selected
item. (Please refer to your Windows documentation for
additional information regarding the Windows keys.)
(Figure 2-10)
■
Cursor keys: Your keyboard contains four arrow
keys for moving the cursor or insertion point to the
right, left, up, or down within windows, applications
and documents.
■
Function keys: The keys labeled [F1] through [F12],
are used in conjunction with the [Fn] key to produce
special actions that vary depending on what program
is running.
■
Windows keys: These keys work with your Windows
operating system and function the same as the
onscreen Start menu button, or the right button
on your pointing device.
CURSOR KEYS
The cursor keys are the four arrow keys on the keyboard
which allow you to move the cursor up, down, left and
right in applications. In programs such as Windows
Explorer, it moves the “focus” (selects the next item up,
down, left, or right). (Figure 2-10)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 14 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
FUNCTION KEYS
Your LifeBook notebook has 12 function keys, F1
through F12. The functions assigned to these keys differ
for each application. You should refer to your software
documentation to find out how these keys are used.
(Figure 2-10)
The [Fn] key provides extended functions for the
notebook and is always used in conjunction with
another key.
■
[Fn+F3]: Pressing [F3] while holding [Fn] will toggle
the Audio Mute on and off.
■
[Fn+F4]: Pressing [F4] while holding [Fn] will toggle
the Quick Point feature on and off. Note that the
[Fn+F4] combination only works if Manual Setting is
selected in the BIOS. (See “BIOS Setup Utility” on
page 29)
■
[Fn+F6]: Pressing [F6] repeatedly while holding [Fn]
will lower the brightness of your display.*
■
[Fn+F7]: Pressing [F7] repeatedly while holding [Fn]
will increase the brightness of the display.*
■
[Fn+F8]: Pressing [F8] repeatedly while holding [Fn]
will decrease the volume of your LifeBook note-
book.**
■
[Fn+F9]: Pressing [F9] repeatedly while holding [Fn]
will increase the volume of your LifeBook notebook.**
* There are eight brightness levels.
** There are 26 audio levels.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 15 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Optional Quick Point Control
Cursor Control
Left Button
Scroll Button
Right Button
Figure 2-11. Touchpad pointing device
CLICKING
Touchpad Pointing Device
Clicking means pushing and releasing a button. To left-
click, move the cursor to the item you wish to select,
press the left button once, and then immediately release
it. To right-click, move the mouse cursor to the item you
wish to select, press the right button once, and then
immediately release it. You also have the option to
perform the clicking operation by tapping lightly on the
Touchpad once. (Figure 2-12)
Certain S7000 LifeBook notebooks are
equipped with an optional “Quick Point”
button for moving the cursor. For more
information about Quick Point, see
“Optional Quick Point Feature” on
page 16.
The Touchpad pointing device comes built into your
Fujitsu LifeBook notebook. It is used to control the
movement of the pointer to select items on your display
panel. The Touchpad is composed of a cursor control, a
left and right button, and a scrolling button. The cursor
control works the same way a mouse does, and moves
the cursor around the display. It only requires light pres-
sure with the tip of your finger. The left and right
buttons function the same as mouse buttons. The actual
functionality of the buttons may vary depending on the
application that is being used. The scrolling button
allows you to navigate quickly through pages, without
having to use the scroll bars. (Figure 2-11)
Figure 2-12 Clicking
DOUBLE-CLICKING
Double-clicking means pushing and releasing the left
button twice in rapid succession. This procedure does
not function with the right button. To double-click,
move the cursor to the item you wish to select, press
the left button twice, and then immediately release it.
You also have the option to perform the double-click
operation by tapping lightly on the Touchpad twice.
(Figure 2-13)
An external mouse can be connected to
either the USB port on your LifeBook note-
book or the USB or PS/2 ports on the
optional port replicator, and used simulta-
neously with the Touchpad. However, if
you boot the system with an external
mouse connected the Touchpad will be
disabled or enabled depending on the
specifications in your BIOS settings. (See
BIOS Setup Utility on page 29 for more
information)
Figure 2-13 Double-clicking
15
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 16 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
TOUCHPAD CONTROL ADJUSTMENT
The Windows Control Panel allows you to customize your
Touchpad with selections made from within the Mouse
Properties dialog box.
■
If the interval between clicks is too
long, the double-click will not be
executed.
■
Parameters for the Touchpad can be
SCROLLING
adjusted from the Mouse Properties
dialog box located in the Windows
Control Panel.
Using the Scrolling button allows you to navigate
through a document quickly without using the window’s
scroll bars. This is particularly useful when you are navi-
gating through on-line pages. To use the Scrolling
button, press the crescent shape at the top or bottom of
the button to scroll up or down a page. When you have
reached the desired section of the page, release the
button. (Figure 2-15)
DRAGGING
Dragging means pressing and holding the left button,
while moving the cursor. To drag, move the cursor to
the item you wish to move. Press and hold the left
button while moving the item to its new location
and then release it. Dragging can also be done using the
Touchpad. First, tap the Touchpad twice over the item
you wish to move making sure to leave your finger on
the pad after the final tap. Next, move the object to its
new location by moving your finger across the
Touchpad, and then release your finger. (Figure 2-14)
Figure 2-15 Scrolling
OPTIONAL QUICK POINT FEATURE
The optional Quick Point device consists of a cursor
control button at the lower center of the keyboard. It is
roughly the same size and shape as a pencil eraser. The
cursor control works the same way a mouse ball does,
and moves the cursor around the display. It only requires
light pressure to move; the more pressure you use, the
faster the cursor will move.
Figure 2-14 Dragging
When used with the Quick Point button, the middle
Touchpad button allows you to scroll up and down a
screen.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 17 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
will decrease the volume of your notebook. Pressing
[F9] repeatedly while holding [Fn] will increase the
volume of your notebook.
Volume Control
Your Fujitsu LifeBook notebook has multiple volume
controls which interact with each other.
There are 26 levels through which the
function keys cycle.
Any software that contains audio files will
also contain a volume control of its own. If
you install an external audio device that
has an independent volume control, the
hardware volume control and the software
volume control will interact with each
other. It should be noted that if you set
your software volume to Off, you will
override the external volume control
setting.
■
■
Volume can be controlled by many volume controls
that are set within individual applications.
Certain external audio devices you might connect to
your system may have hardware volume controls.
Each source discussed above puts an upper limit on the
volume level that must then be followed by the other
sources.
CONTROLLING THE VOLUME
The volume can be controlled in several different ways:
We recommend that you experiment with the various
volume controls to discover the optimal sound level.
■
Volume can be set from within the Volume Control on
the Taskbar.
■
Volume can be controlled with the F8 and F9 func-
tions keys. Pressing [F8] repeatedly while holding [Fn]
17
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 18 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Flexible Bay Eject Lever
Flexible Bay
Figure 2-16 Flexible Bay
Cold-swapping
To cold-swap modular devices in your Flexible Bay
follow these easy steps: (Figure 2-17)
Flexible Bay Devices
Your Fujitsu LifeBook notebook contains a Flexible Bay.
The Flexible Bay can house an optical drive, a Lithium
ion battery, and a weight saver. (Figure 2-16)
1. Close any open files.
2. Shut down your LifeBook notebook.
Your Flexible Bay will have one of the following devices
installed.
3. Pull out the Flexible Bay eject lever. This will push
your device out slightly, allowing you to remove the
device.
■
Modular Super-Multi DVD drive: This allows you to
access movies, software, and audio DVD/CDs and
record to DVD, CD, and DVD-RAM discs.
4. Slide your device out until it is clear of the bay.
This will require light force.
■
Modular DVD/CD-RW combo drive: This allows you
to access movies, software, and audio DVD/CDs as
well as to write to CDs.
Flexible Bay Eject Lever
■
■
Modular CD-ROM drive: This allows you to access
software, data, or audio CDs.
Modular Lithium ion battery: This is a rechargeable
battery that can be used to power your LifeBook note-
book when an adapter is not connected.
(b)
(a)
(c)
■
Weight Saver: This is used to fill the bay when no
device is needed.
REMOVING AND INSTALLING
MODULAR DEVICES
There are two ways to remove and install modular
(d)
devices in the Flexible Bay:
Figure 2-17 Removing/Installing a device in the Flexible Bay
■
Cold-swapping: swapping devices while your LifeBook
Be careful when aligning and seating
devices in the bay. If the fit is incorrect,
you may damage the bay or the device. If
the device does not move easily in the bay,
remove it, and check for dirt or foreign
objects. It will require a firm push to latch
the device in place.
notebook is powered off.
■
Hot-swapping: swapping devices while your system is
active using the Unplug/Eject icon from your taskbar.
Note that if the weight saver is installed rather than a
modular device, it is not necessary to use BayManager
when removing it.
You should never leave your Flexible Bay
empty when the notebook is in operation.
If left empty, dust or foreign matter may
accumulate inside the notebook.
5. Slide the device you are installing into your
notebook until it clicks into place.
6. It is now safe to turn your notebook back on.
7. You can now access and use the device.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 19 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
Your LifeBook notebook will automatically detect the
new device and activate it within your system. The drive
letters associated with the device will be created and
listed under My Computer and Windows Explorer.
Hot-swapping
Under Windows 2000 Professional, Windows XP Home,
and Windows XP Professional, hot-swapping is
provided through the Unplug or Eject Hardware utility.
The icon for the utility appears on the taskbar. Click on
the icon and follow the on-screen instructions.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 20 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Button 1*
Button 2*
Button 3*
Button 4*
Enter button
* Security/Application Launcher
buttons (for entering passwords
and launching applications)
Figure 2-18 LifeBook Security/Application Panel
use a common password. A password consists of one to
five button strokes plus the enter button. A valid stroke
consists of pushing one or up to four buttons simulta-
neously. The following are valid button strokes:
LifeBook Security/
Application Panel
A unique feature of your LifeBook notebook is the
Security/Application Panel that allows you to secure your
notebook from unauthorized use. The Security/Applica-
tion Panel also allows you to launch applications with the
touch of a button when your system is on.
n
Pushing [4] by itself
Pushing [2] and [3] at the same time
Pushing [1], [2], and [4] at the same time
n
n
n
Pushing [1], [2], [3], and [4] at the same time
The following are valid passwords. The numbers
within braces ({ }) are button strokes using more
than one button.
If the security system is activated, upon starting your
notebook or resuming from suspend mode the security
system requires you to enter a password code using the
buttons on the Security/Application Panel. After entering
a correct password, your notebook resumes system
operation. (Figure 2-18)
n
{[2]+[3]}, [1], [enter]
[4], [enter]
n
n
{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [enter]
Setting Passwords
SETTING UP YOUR
When shipped from the factory, no passwords are set.
You have a choice of having no password or setting a
supervisor and user password. You must set the super-
LIFEBOOK SECURITY PANEL
When you receive your LifeBook notebook, the security
panel application is pre-installed without any passwords.
The following sections provide detailed information on
your security panel, and how to set, change or remove
passwords.
visor password before the user password.
n
The purpose of supervisor password is
to be able to bypass the user password
in case the user password is forgotten.
The supervisor password alone will not
lock the system.
You have to set both the supervisor
and user passwords for the security
panel to work.
Numbered Buttons
Use these buttons to enter your password.(Figure 2-18)
n
Enter Button
After entering the button strokes, push this button to
enter the password into the LifeBook notebook.
(Figure 2-18)
Setting Supervisor Password
You must have set a supervisor password before setting
any user passwords. The supervisor password can bypass
the user password.
PASSWORDS
The user and supervisor password may be set on this
notebook. A supervisor password is typically the same
for all LifeBook notebooks in a working group, office, or
company to allow for system management. Individual
LifeBook notebooks in a group environment should not
1. Go to the Start menu.
2. Click on Run.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 21 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
3. Type in:
vate the notebook after a password failure, you must
press the Power/Suspend/Resume button, then enter a
C:\Program Files\Fujitsu\
Security Panel Application\
Supervisor\FJSECS.EXE,
then press [Enter]
correct password.
Remember the user password you
4. Follow the on-screen instructions to set the
Supervisor password.
specified on the Security Panel Application.
If you forget the password you will not be
able to use your computer. The super-visor
password can override the user password.
Setting User Password
1
Go to the Start menu.
2. Click on Programs.
PRECAUTIONS
Opening and Closing the Cover
Closing the cover automatically places the notebook into
suspend mode. Opening the cover does not automati-
cally place the notebook into normal operation. Instead,
you must enter the proper security password after
pushing the Power/Suspend/Resume button.
3. Click on Security Panel Application and
Set User Password.
4. Follow the on-screen instructions to set the
user password.
You may change or remove the supervisor
or user password by repeating the steps
defined above.
Low Battery Operations
If your LifeBook notebook has low battery, pushing the
Power/Suspend/Resume button only turns on the Secu-
rity Indicator. Your notebook does not unlock, the Secu-
rity Indicator turns off after one minute. To resume
normal operation, first attach a power supply to the
notebook. Then you may unlock the notebook.
OPERATING YOUR LIFEBOOK SECURITY/
APPLICATION PANEL
The security lock feature is in effect both when the system
resumes from Off or suspend state. You always need to
push the Suspend /Resume button to input the user pass-
word. Your system will not begin the boot sequence
without entering your supervisor/user password.
UNINSTALLING THE SECURITY
PANEL APPLICATION
You have two options when uninstalling the security
panel application:
From Off State
1. Turn on your system.
n
Uninstall the security panel application software.
This will disable all security feature.
Uninstall the security panel application with password
2. When the Security Indicator flashes, enter the pass-
word and press Enter button.
n
still active. This will not allow any changes to the
password.
For example, if the password is 22222,
Press Button Number 2 five times and press Enter
button.
Uninstalling the Security Panel
The LifeBook notebook will boot to normal opera-
tion.
Application Software
Remove passwords when User wants no password
protection whatsoever and doesn’t want to give anybody
the utility to set a password on their computer. In this
case, if passwords (supervisor, user, or both) are set, the
passwords must first be cleared BEFORE removing the
application. To clear passwords, follow same procedure
in SETTING PASSWORD CODES except this time,
select REMOVE, enter current password then click Next.
When asked to confirm select Yes.
From Suspend State
1. Press your Power/Suspend/Resume button.
2. When the Security Indicator flashes, enter the pass-
word and press Enter button.
The notebook should resume normal operation.
Incorrect Password Entry
If an invalid supervisor or user password is entered three
times in succession, the system will “beep” for about one
minute. If a valid password is entered within a minute
(while system beeps), the beeping will stop and the note-
book will resume normal operation. If no password (or
an invalid one) is entered while the system beeps, the
system will return to its previous locked state (suspend
or off) and the Security Indicator will go off. To reacti-
21
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 22 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Removing Security Panel Application with
Passwords Still Active
Using this feature will not allow any changes to the
If you forget both passwords, please contact Fujitsu
Computer Systems Corporation Service and Support at
1-800-8FUJITSU (1-800-838-5487). Fujitsu Computer
Systems Corporation charges a service fee for unlocking
a password restricted LifeBook notebook. When calling
please have a valid credit card and provide proof of
ownership. You will then be given instructions on where
to ship your notebook.
password.
Removing the applications does not
remove the password. It simply removes
the utility to change/add/remove
passwords. To change your password you
must reinstall the application.
LAUNCHING APPLICATIONS WITH
THE SECURITY/APPLICATION PANEL
User:
The security panel also enables you to launch applications
with the touch of a button when your system is on.
Pressing any of the buttons will launch a user-defined
application. Your notebook is pre-installed with software
utilities that let you operate and configure your LifeBook
Security /Application Panel. These utilities are found in
the Start menu, under Settings -> Control Panel ->
Application Panel. (For Windows XP users, go to Start ->
Control Panel -> Other Control Panel Settings ->
Application Panel. They include two Application Panel
Setup tabs, E-mail Setup, and Internet Setup.
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application in the list, and
click Add/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Supervisor:
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the
Configuring your LifeBook Application Panel
When you start Windows, the LifeBook Application
Panel is automatically activated. An icon resembling a
finger pressing a button will appear on the system tray
(the indented portion of the status bar where the clock is
displayed). When you see this icon you will know that
LifeBook Application Panel is active.
Control Panel.
3. Select the Security Panel Application for
Supervisor in the list, and click Add/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Reinstalling the Security/Application Panel
To reinstall supervisor or user security application, you
will need your Drivers and Applications CD. The
Utilities/Security Application Panel folder contains two
separate folders: Supervisor and User. The setup files for
supervisor and user security applications are contained
in those folders.
As an application launcher, the LifeBook Application
Panel is very flexible, giving you a variety of options. To
set up the Panel to best suit your needs, we have
provided the Application Panel Setup utility that quickly
and easily helps you make the most of this valuable
feature.
To configure your LifeBook Application Panel with
Application Panel Setup:
1. Click on Start.
1. Go to the Utilities/Security Application Pane/
Supervisor folder on the CD and double-click the
setups.exe file. The Installing Security Panel Appli-
cation window will appear. Follow the instructions
on the screen.
2. Click on Programs.
3. Click on LifeBook Application Panel.
4. Click on Application Panel Setup.
2. Go to the Utilities/Security Application Panel/User
folder on the CD and double-click the setup.exe file.
The Installing Security Panel Application window
will appear. Follow the instructions on the screen.
The Application Panel Setup utility will appear. There
are tabs that correspond to the application buttons on
the LifeBook Application Panel. When you receive your
notebook, these buttons are pre-configured to launch
specific programs, as referenced in Chapter 7 of this
document.
Supervisor and user passwords can be set via Windows
software using the FJSECS.exe and FJSECU.exe files,
respectively. FJSECU.exe for the user password cannot
run without first setting a supervisor password. You
need to run FJSECS.exe first to set the supervisor pass-
word. Follow instructions under Setting Passwords on
page 20.
The tabs in Application Panel Setup may
not be in the same order as the buttons on
your LifeBook notebook, please select the
tab you wish to change carefully.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 23 Thursday, February 19, 2004 4:52 PM
G e t t i n g t o K n o w Yo u r L i f e B o o k
To change an application associated with the Application
buttons, click on the tab for the button you would like to
reconfigure – for example, Application A. Click on
Browse from Start Menu, scroll down the list of applica-
tions, click on the application you wish to launch with
this button, and then click OK. The button will now
launch the new application.
Deactivating and Activating the LifeBook
Application Panel
To deactivate the LifeBook Application Panel, follow
these easy steps:
1. Click on Start.
2. Click on Programs.
3. Click on LifeBook Application Panel.
4. Click on Deactivate Panel.
The Internet tab is different. It comes set to launch your
Windows default Internet browser (Internet Explorer),
unless you have changed this in Windows. In order to
reconfigure it to launch another program follow these
easy steps:
To reactivate, follow the same procedure, except for
step 4. Click on Activate Panel instead.
1. Click on Other from the Internet browser box.
2. Click on Browse from Start Menu.
Every time you start Windows the
LifeBook Application Panel is activated,
even if you deactivated it before you shut
down.
3. Scroll down the list of applications, and then click
on the application you wish to launch with this
button.
4. Click OK.
The button will now launch the new application. If you
want to return to launching your Windows default
Internet browser with this button, you need only click
on “Default Internet Browser” from the Internet browser
box. Be aware that you will erase the settings for the
“other application”. If you wish to go back to launching
the “other application” from this button, you will need
to reconfigure it as described above.
If your system has dedicated one of the
application launcher buttons to be an
Internet launcher, the button can still be
configured to launch any application you
wish, not just an Internet browser.
When you have finished with Application Panel Setup
click OK, and the new settings will take effect. You can
reconfigure your LifeBook Application Panel as often as
you like.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 24 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
24
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 25 Thursday, February 19, 2004 4:52 PM
3
Getting Started
25
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 26 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
26
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 27 Thursday, February 19, 2004 4:52 PM
G e t t i n g S t a r t e d
DC Power
Jack
DC Output Cable
AC Adapter
AC Cable
Figure 3-1 Connecting the AC Adapter
2. Plug the Auto/Airline adapter into the cigarette
lighter of an automobile with the ignition key in
the On or Accessories position.
Power Sources
Your Fujitsu LifeBook notebook has three possible
power sources: a primary Lithium ion battery, an AC
adapter or an optional Auto/Airline adapter.
OR
3. Plug the Auto/Airline adapter into the DC power
jack on an airplane seat.
CONNECTING THE POWER ADAPTERS
The AC adapter or optional Auto/Airline adapter
provides power for operating your notebook and
charging the batteries.
Switching from AC Adapter Power or the
Auto/Airline Adapter to Battery Power
1. Be sure that you have at least one charged
battery installed.
Connecting the AC Adapter
1. Plug the DC output cable into the DC power jack
2. Remove the AC adapter or the Auto/Airline adapter.
of your LifeBook notebook.
The Lithium ion battery is not charged
upon purchase. Initially, you will need to
connect either the AC adapter or the
Auto/Airline adapter to use your
notebook.
2. Plug the AC adapter into an AC electrical outlet.
(Figure 3-1)
Connecting the Optional Auto/Airline Adapter
1. Plug the DC output cable into the DC power jack
on your notebook.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 28 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Display Panel Latch
Figure 3-2 Opening the Display Panel
Using the Power Management Utility
(Windows 2000 only)
Adjusting the brightness using the Power Management
changes the setting permanently.
Display Panel
Your Fujitsu LifeBook notebook contains a display panel
that is backlit for easier viewing in bright environments
and maintains top resolution through the use of active-
matrix technology.
1. Double-click the BatteryAid icon
in the lower
right corner of your display. This will open the
BatteryAid Properties dialog box.
OPENING THE DISPLAY PANEL
1. Press the Display Panel latch. This releases the
2. Select the Power Control tab and adjust your
LCD Backlighting to the desired level.
locking mechanism and raises the display slightly.
2. Lift the display backwards, being careful not to
touch the screen, until it is at a comfortable
viewing angle. (Figure 3-2)
3. Click OK or Apply to permanently change
the settings.
You may need to readjust the brightness level periodi-
cally depending on your operating environment.
ADJUSTING DISPLAY PANEL BRIGHTNESS
Once you have turned on your LifeBook notebook, you
may want to adjust the brightness level of the screen to a
more comfortable viewing level. There are two ways to
adjust the brightness, by using the keyboard or the
power management utility.
The higher the brightness level, the more
power the notebook will consume and the
faster your batteries will discharge. For
maximum battery life, make sure that the
brightness is set as low as possible.
Using the Keyboard
Adjusting the brightness using the keyboard changes the
setting only temporarily.
CLOSING THE DISPLAY PANEL
1. Holding the edge of your display panel, pull it
forward until it is flush with the body of your Life-
Book notebook.
■
[Fn+F6]: Pressing repeatedly will lower the
brightness of your display.
■
[Fn+F7]: Pressing repeatedly will increase the
brightness of the display.
2. Push down until you hear a click. This will
engage the locking mechanism and prevent
your display panel from opening unexpectedly.
When using AC power your brightness
setting is set to its highest level by default.
When using battery power your brightness
setting is set to approximately mid-level by
default.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 29 Thursday, February 19, 2004 4:52 PM
G e t t i n g S t a r t e d
BOOT SEQUENCE
Starting Your
The procedure for starting up your notebook is called
the Bootup sequence and involves your notebook’s
BIOS. When your LifeBook notebook is first turned on,
the main system memory is empty, and it needs to find
instructions to start up your notebook. This information
is in the BIOS program. Each time you power up or
restart your notebook, it goes through a boot sequence
which displays a Fujitsu logo until your operating system
is loaded. During booting, your notebook is performing
a standard boot sequence including a Power On Self Test
(POST). If the sequence is completed without a failure
and without a request for the BIOS Setup Utility, the
system displays the operating system’s opening screen.
LifeBook Notebook
POWER ON
Power/Suspend/Resume Button
The Power/Suspend/Resume button is used to turn on
your LifeBook notebook from its off state. Once you
have connected your AC adapter or charged the internal
Lithium ion battery, you can power on your LifeBook
notebook. (See figure 2-3 on page 6 for location)
When you turn on your LifeBook
notebook be sure you have a power
source. This means that at least one
battery is installed and charged, or that the
AC or Auto/Airline adapter is connected
and has power.
The boot sequence is executed when:
■
You turn on the power to your LifeBook notebook.
■
You restart your notebook from the Windows
Shut Down dialog box.
■
The software initiates a system restart. Example:
To turn on your LifeBook notebook from its off state,
press the Power/Suspend/Resume button, located above
the keyboard. When you are done working you can
either leave your LifeBook notebook in Suspend mode,
(See Suspend Mode on page 32 for more information), or
you can turn it off (See Power Off on page 33 for more
information).
When you install a new application.
■
You reset the system by pressing [CTRL+ALT+DEL].
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your LifeBook notebook.
Your BIOS is set at the factory for normal operating
conditions, therefore there is no need to set or change
the BIOS’ environment to operate your notebook.
Do not carry your LifeBook notebook
around with the power on or subject it to
shocks or vibration, as you risk damaging
your notebook.
The BIOS Setup Utility configures:
■
Device control feature parameters, such as changing
I/O addresses and boot devices.
When you power on your LifeBook, it will perform a
Power On Self Test (POST) to check the internal parts and
configuration for correct functionality. If a fault is found,
your LifeBook notebook will emit an audio warning and/
or an error message will be displayed. (See Power On Self
Test Messages on page 64 for more information)
Depending on the nature of the problem, you may be able
to continue by starting the operating system or by
entering the BIOS setup utility and revising the settings.
■
System Data Security feature parameters, such as
passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your LifeBook notebook.
2. Press the [F2] key once the Fujitsu logo appears on
the screen. This will open the main menu of the
BIOS Setup Utility with the current settings
displayed.
After satisfactory completion of the Power On Self Test
(POST), your notebook will load your operating system.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key
to scroll through the other setup menus to review or
alter the current settings.
Never turn off your LifeBook notebook
during the Power On Self Test (POST) or it
will cause an error message to be displayed
when you turn your LifeBook notebook on
the next time. (See Power On Self Test
Messages on page 64 for more
BIOS Guide
A guide to your notebook’s BIOS is available online.
Please visit our service and support Web site at
us.fujitsu.com/computers. Once there, select Support,
then select Notebooks under User’s Guides. Select Life-
Book BIOS Guides from the pull-down menu for your
LifeBook series. If you are unsure of your notebook’s
BIOS number, refer to your packing slip.
information)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 30 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
simply like to move on, and register at a later time, you
may click the Skip button, and you will go directly to the
Condition of Use page.
If your data security settings require it, you
may be asked for a password before the
BIOS main menu will appear.
Registration
If your connection is successful, you will go to the
Registration Confirmation page. On this page simply
enter the requested information, and then check the
box at the bottom to register your copy of Windows with
Microsoft. Once you have finished, click the Next button
to continue.
BOOTING THE SYSTEM
We strongly recommend that you do not attach any
external devices and do not put a DVD/CD in any drive
until you have gone through the initial power on
sequence.
If you do not register at this time you can
do it later simply by double-clicking on the
LifeBook Registration icon on your
When you turn on your LifeBook notebook for the first
time, it will display a Fujitsu logo on the screen. If you
do nothing the system will load the operating system,
and then the Windows Welcome will begin.
desktop and following the instructions.
You will then go through the Fujitsu registration process.
Follow the instructions on the screens, and enter all of
the necessary information. Be as specific as possible so
that if you need help the service and support team will
be able to serve you better.
Designed to accommodate the needs of users in many
different countries, Windows needs to be configured the
first time you use it. Windows has three parts:
■
Getting Started: You have the opportunity to enter
Final Settings
custom information for your configuration file and
setup your modem so that your LifeBook notebook
will be prepared to dial out.
The first part of your final settings is the Windows End
User License Agreement. Read the agreement carefully.
When you finish reading you must accept or reject the
terms of the agreement and then click on the Next button.
■
Registration: Easy online registration for Windows
with Microsoft, and for your LifeBook notebook with
Fujitsu.
If you reject the terms of the license
agreement you will be asked to review the
license agreement for information on
returning to Windows or to shut down
your LifeBook notebook.
■
Windows License Agreement and Final Settings:
You have the opportunity to review the Windows.
Getting Started
Read the instructions on the screens carefully and fill in
the information as directed. You will be asked for such
items as the language you wish to use, the country in
which you live, your first and last name, and about how
you dial out from where you will be using your note-
book. For the modem settings, enter your current
location information where you will be using your
LifeBook notebook. If you are not connected to a phone
line and plan to register at a later time, you may click the
Skip button, and you will go directly to the condition of
WINDOWS PRODUCT ACTIVATION
(WINDOWS XP ONLY)
If your system has Windows XP as an operating system,
it has already been pre-installed and pre-activated when
you receive the system.
In the event you need to re-install Windows XP (e.g.,
after making significant configuration changes), it may
be necessary to reactivate the operating system. To do so,
use the following information.
use page.
Make sure you have connected a phone
line to your modem before you use E-
Registration.
■
After re-installing Windows XP, you have thirty days to
activate it. Product activation ensures that you are the
authorized owner of the Windows XP operating sys-
tem.
Once you have set up your notebook to dial out,
■
Until you activate the product, you will be prompted
Windows will make a free telephone call which will test
these settings. If the call is unsuccessful, you will be
returned to the phone settings page where you may try
to fix them. If you are unable to fix the settings please
contact Fujitsu Service and Support. (See Fujitsu Contact
Information on page 1 for more information) If you would
whenever you turn on the system that activation is
required. Follow the on-screen directions to activate
your operating system. The product only needs to be
30
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 31 Thursday, February 19, 2004 4:52 PM
G e t t i n g S t a r t e d
activated once, unless significant hardware changes are
made to your system.
■
Note that Product Activation and Registration are not
the same thing. Registration is optional, whereas Prod-
uct Activation is a required procedure.
REGISTERING YOUR LIFEBOOK NOTEBOOK
How do I register?
To register, visit our Web site at:
us.fujitsu.com/computers
INSTALLING CLICK ME!
The first time you boot up your system, you will see an
icon called Click Me!. (The icon is located on the
desktop for Windows 2000 systems; it is located in the
Start menu for Windows XP systems). When you click
the Click Me! icon, your system will automatically build
the icon tray in the bottom right of the screen. These
icons provide links to utilities that you will frequently
access.
Click Me! will install additional system utilities to maxi-
mize the performance of your system.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 32 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
■
Allowing the battery to reach the Dead Battery
Warning condition.
Power Management
Your Fujitsu LifeBook notebook has many options and
features for conserving battery power. Some of these
features are automatic and need no user intervention,
such as those for the internal modem. However, others
depend on the parameters you set to best suit your oper-
ating conditions, such as those for the display bright-
ness. Internal power management for your notebook
may be controlled from settings made in your operating
system, pre-bundled power management application, or
from settings made in BIOS setup utility.
Your notebook’s system memory typically stores the file
on which you are working, open application informa-
tion, and any other data required to support operations
in progress. When you resume operation from Suspend
mode, your notebook will return to the point where it left
off. You must use the Power/Suspend/Resume button to
resume operation, and there must be an adequate power
source available, or your notebook will not resume.
■
If you are running your LifeBook note-
book on battery power, be aware that
the battery continues to discharge while
your notebook is in Suspend mode,
though not as fast as when fully opera-
tional.
Besides the options available for conserving battery
power, there are also some things that you can do to
prevent your battery from running down as quickly.
For example, you can create an appropriate power saving
profile, put your notebook into Suspend mode when it
is not performing an operation, and you can limit the
use of high power devices. As with all mobile, battery
powered computers, there is a trade-off between
performance and power savings.
■
Disabling the Power/Suspend/Resume
button prevents it from being used to
put your LifeBook notebook in Suspend
or Hibernation (Save-to-Disk) mode.
The resume function of the button can-
not be disabled.
POWER/SUSPEND/RESUME BUTTON
When your LifeBook notebook is active, the Power/
Suspend/Resume button can be used to manually put
your notebook into Suspend mode. Push the Power/
Suspend/Resume button when your notebook is active,
but not actively accessing anything, and immediately
release the button. You will hear two short beeps and
your system will enter Suspend mode. (See figure 2-3 on
page 6 for location)
■
The Suspend or Hibernation (Save-to-
Disk) mode should not be used with cer-
tain PC Cards. Check your PC Card doc-
umentation for more information. When
PC Cards or external devices are in use,
Hibernation (Save-to-Disk) mode cannot
return to the exact state prior to suspen-
sion, because all of the peripheral
devices will be re-initialized when the
system restarts.
If your LifeBook is suspended, pushing the Power/
Suspend/Resume button returns your notebook to active
operation. You can tell whether the system is Suspended
by looking at the Power indicator. (See figure 2-3 on
page 6) If the indicator is visible and not flashing, your
notebook is fully operational. If the indicator is visible
and flashing, your notebook is in Suspend mode. If the
indicator is not visible, the power is off or your notebook
is in Hibernation mode. (See Hibernation Feature)
■
If your LifeBook notebook is actively
accessing information when you enter
the Suspend or Hibernation (Save-to-
Disk) mode, changes to open files are
not lost. The files are left open and
memory is kept active during Suspend
mode or the memory is transferred to
the internal hard drive during Hiberna-
tion mode.
The main advantage of using the
SUSPEND MODE
Hibernation (Save-to-Disk) function is that
power is not required to maintain your
data. This is particularly important if you
will be leaving your LifeBook notebook in
a suspended state for a prolonged period
of time. The drawback of using
Hibernation mode is that it lengthens the
power down and power up sequences and
resets peripheral devices.
Suspend or Standby mode in Windows saves the
contents of your LifeBook notebook’s system memory
during periods of inactivity by maintaining power to
critical parts. This mode will turn off the CPU, the
display, the hard drive, and all of the other internal
components except those necessary to maintain system
memory and allow for restarting. Your notebook can be
put in Suspend mode by:
■
Pressing the Power/Suspend/Resume button when
your system is turned on.
Selecting Standby from the Windows Shut Down menu.
Timing out from lack of activity.
■
■
32
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 33 Thursday, February 19, 2004 4:52 PM
G e t t i n g S t a r t e d
HIBERNATION (SAVE-TO-DISK) FEATURE
The Hibernation feature saves the contents of your
LifeBook notebook’s system memory to the hard drive as
a part of the Suspend/Resume mode. You can enable or
disable this feature.
RESTARTING THE SYSTEM
If your system is on and you need to restart it, be sure
that you use the following procedure.
1. Click the Start button, and then click Shut Down.
2. Select the Restart option from within the Windows
Enable or Disable the Hibernation Feature
The default settings is not enabled. To enable or disable
the Hibernation feature follow these easy steps:
Shut Down dialog box.
3. Click OK to restart your notebook. Your notebook
will shut down and then reboot.
1. From the Start menu, select Settings, and then select
Control Panel.
Turning off your notebook without exiting
Windows, or turning it on within 10
seconds of being shut off may cause an
error when you start the next time.
2. From the Control Panel select Power Options.
3. Select the Hibernation tab. Select the box to enable
or disable this feature.
POWER OFF
Using the Hibernation Feature
1. From the Start menu, select Settings, and then select
Control Panel.
Before turning off the power, check that the Hard Drive,
optical drive, PC Card, and Floppy Disk indicators are
all Off. (See figure 2-3 on page 6). If you power-off while
accessing a disk or PC Card there is a risk of data loss. To
ensure that the notebook shuts down without error, use
the Windows shutdown procedure.
2. From the Control Panel select Power Options.
3. Select the Advanced tab. Select Hibernate from the
pull down menu for Power buttons.
DISPLAY TIMEOUT
Be sure to close all files, exit all
applications, and shut down your
operating system prior to turning off the
power. If files are open when you turn the
power off, you will lose any changes that
have not been saved, and may cause disk
errors.
The Video Timeout is one of the power management
parameters. This feature saves power by turning off the
display if there is no keyboard or pointer activity for the
user selected timeout period. Any keyboard or pointer
activity will cause the display to restart automatically.
This feature is independent of the Power/Suspend/
Resume button and can be enabled and disabled in
Windows and BIOS setup utility. (See BIOS Setup Utility
on page 29 for more information)
Using the correct procedure to shut down from Windows
allows your notebook to complete its operations and turn
off power in the proper sequence to avoid errors. The
proper sequence is:
HARD DISK TIMEOUT
The Hard Disk Timeout is another one of the power
management parameters. This feature saves power by
turning off the hard drive if there is no hard drive
activity for the user selected timeout period. Any
attempt to access the hard drive will cause it to restart
automatically. This feature is independent of the Power/
Suspend/Resume button and can be enabled and
disabled in Windows and BIOS setup utility. (See BIOS
Setup Utility on page 29 for more information)
1. Click the Start button, and then click Shut Down or
Turn Off Computer.
2. Select the Shut Down option from within the
Windows Shut Down dialog box.
3. Click OK to shut down your notebook.
If you are going to store your notebook for a month or
more see Care and Maintenance Section.
WINDOWS POWER MANAGEMENT
Power Management
The Power Management icon located in the Windows
Control Panel allows you to configure some power
management settings. For example, you can use Power
Management to set the timeout values for turning off the
display and hard disks whether you are running the
notebook on battery power or one of the adapters. The
settings may also be changed in the BIOS. (See BIOS
Setup Utility on page 29 for more information)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 34 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
34
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 35 Thursday, February 19, 2004 4:52 PM
4
User-Installable
Features
35
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 36 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
36
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 37 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
RECHARGING THE BATTERIES
Lithium ion Battery
If you want to know the condition of the primary
Lithium ion battery, check the Battery Level indicator
located on the Status Indicator panel. The indicator
changes as the battery level changes.
Your LifeBook notebook has a Lithium ion battery that
provides power for operating your notebook when no
external power source is available. The battery is durable
and long lasting, but should not be exposed to extreme
temperatures, high voltages, chemicals or other hazards.
The Lithium ion battery is recharged internally using
the AC adapter or Auto/Airline adapter. To recharge the
battery make sure the battery that needs to be charged
is installed in your LifeBook notebook and connect the
AC or Auto/Airline adapter.
The Lithium ion battery operating time may become
shorter if it is used under the following conditions:
■
When used at temperatures that exceeds a low of 5°C
or a high of 35°C. Extreme temperatures not only
reduce charging efficiency, but can also cause battery
deterioration. The Charging icon on the Status Indi-
cator panel will flash when you try to charge a battery
that is outside its operating temperature range.
(See Battery Charging Indicators on page 12 for more
information)
Make sure that the Battery Charging
indicator and the percentage charge is
shown inside the Battery Level icon on the
Status Indicator Panel.
There is no memory effect on the Lithium ion battery
therefore you do not need to discharge the battery
completely before recharging. The charge times will be
significantly longer if your notebook is in use while the
battery is charging. If you want to charge the battery
more quickly, put your notebook into Suspend mode,
or turn it off while the adapter is charging the battery.
(See Power Management on page 32 for more information
■
When using a high current device such as a modem,
Super-Multi DVD drive, CD-ROM drive, DVD/CD-
RW combo drive, or the hard drive, using the AC
adapter will conserve your battery life.
Do not leave a faulty battery in your
LifeBook notebook. It may damage your
AC adapter, optional Auto/Airline adapter,
another battery or your notebook itself. It
may also prevent operation of your
notebook by draining all available current
into the bad battery.
on Suspend mode and shutdown procedure)
Using heavy current devices such as
Modem or frequent DVD/CD-RW/CD-
ROM accesses may prevent charging
completely.
■
Actual battery life will vary based on
Low Battery State
screen brightness, applications, fea-
tures, power management settings, bat-
tery condition and other customer
preferences. CD-ROM drive, Super-
Multi DVD drive, DVD/CD-RW drive
combo, or hard drive usage may also
have a significant impact on battery life.
The battery charging capacity is reduced
as the battery ages. If your battery is
running low quickly, you should replace
it with a new one.
When the battery is running low, a low battery notifica-
tion message will appear. If you do not respond to the
low battery message, the batteries will continue to
discharge until they are too low to operate. When this
happens, your notebook will go into Suspend mode.
There is no guarantee that your data will be saved once
the notebook reaches this point.
■
Once the low battery notification mes-
sage appears, you need to save all your
active data and put your LifeBook note-
book into Suspend mode until you can
provide a new power source. You should
provide a charged battery, an AC power
adapter, or Auto/Airline adapter as soon
as possible.
■
Under federal, state, or local law it may
be illegal to dispose of batteries by put-
ting them in the trash. Please take care
of our environment and dispose of bat-
teries properly. Check with your local
government authority for details regard-
ing recycling or disposing of old batter-
ies. If you cannot find this information
elsewhere, contact your support repre-
sentative at 1-800-8FUJITSU (1-800-
838-5487)
■
When you are in Suspend mode there
must always be at least one power
source active. If you remove all power
sources while your LifeBook notebook is
in Suspend mode, any data that has not
been saved to the hard drive will be lost.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 38 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Dead Battery Suspend mode shows on the Status indi-
cator just like the normal Suspend mode. Once your
notebook goes into Dead Battery Suspend mode you will
be unable to resume operation until you provide a
source of power either from an adapter, or a charged
battery. Once you have provided power, you will need to
press the Power/Suspend/Resume button to resume
operation.
Hot-swapping Batteries
To hot-swap batteries in your battery bay follow these
easy steps: (Figure 4-1)
Be sure to plug in an AC Adapter prior to
removing the battery. There is no bridge
battery present to support the system
while the battery is being replaced. If you
do not use an AC Adapter you will lose
any unsaved files.
In the Dead Battery Suspend mode, your data can be
maintained for some time, but if a power source is not
provided promptly, the Power indicator will stop
flashing and go out, meaning that you have lost the data
that was not stored. Once you provide power, you can
continue to use your notebook while an adapter is
charging the battery.
1. Plug an AC Adapter into the system and connect it
to a power outlet.
Latch Release
Battery Bay
Release Latch
Shorted Batteries
The Status Indicator panel uses a symbol inside the
battery outline of the Battery Level indicator to display
the operating level available in that battery. (See figure 2-
9 on page 11) If this display shows a Shorted Battery, it
means the battery is damaged and must be replaced so it
does not damage other parts of your LifeBook notebook.
REPLACING THE BATTERY
With the purchase of an additional battery, you can have
a fully charged spare to swap with one that is not
charged. There are two ways to swap batteries, cold-
swapping and hot-swapping:
Battery Pack
Lift Slot
Cold-swapping Batteries
To cold-swap batteries in your battery bay follow these
Figure 4-1. Removing a Battery
2. Follow steps 3 through 5 in “Cold Swapping
Batteries”.
easy steps: (Figure 4-1)
1. Have a charged battery ready to install.
2. Shut down your notebook and disconnect the AC
adapter.
If the Lithium ion battery connector is not
fully seated, you may not be able to use
your notebook or charge your battery.
3. Unlock the battery bay release latch by pushing the
latch release away from the battery pack and sliding
the battery bay release latch towards the latch release
(Figure 4-1).
4. Continue to press the latch release button away from
the battery pack, and lift the battery out of the bay
by inserting a thumbnail under the edge of the
battery at the lift slot.
5. Slide a new battery into the bay.
6. Slide the battery bay release latch back to its original
position to lock the battery into place.
8. Plug in the AC adapter and turn the power on.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 39 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
Media Eject Button
Media Holder Tray
Figure 4-2. Optical Drive
The Super-Multi DVD drive also supports
burning and reading DVD-RAM. Windows
XP supports burning and reading of DVD-
RAM as a standard feature; Windows
2000 does not support either. To burn
and/or read DVD-RAM with Windows
2000, use the DLA (Drive Letter Access)
utility which comes with RecordNow and
WinDVD Creator.
Optical Drive
There is a variety of media available to use with your
system, depending upon the system configuration you
have selected. Super-Multi DVD drives, DVD/CD-RW
Combo drives, and CD-ROM drives are collectively
known as “optical drives”.
A CD-R or DVD-R disc can only be written to once;
CD-RW or DVD-RW discs can be written to over and
over. CD-R and CD-RW discs hold up to 700MB of data.
DVD-R and DVD-RW discs hold up to 4.7 GB of data.
DVD/CD-RW Combo model only: With the combo drive,
you can play DVD movies, read audio CDs, and write
data onto recordable CD-R or CD-RW discs.
Depending upon the configuration of your LifeBook
notebook, you may have one of the following drives:
CD-ROM model only: With the CD-ROM drive, you can
■
Super-Multi DVD: The Super-Multi DVD drive com-
read software, audio, or data CD discs.
bines seven recordable formats in a single drive (DVD-
R, DVD+R, DVD-RW, DVD+RW, DVD-RAM, CD-R,
and CD-RW), making it the most versatile drive to
date.
■
Do not operate your optical drive
unless your LifeBook notebook is
sitting on a flat surface. Using a drive
when the system is not level may
damage the drive or prevent proper
operation.
■
DVD/CD-RW combo: A DVD/CD-RW combo drive
allows you to access movie, software, data, or audio
DVD/CDs, and to write data onto recordable CD-R
and CD-RW discs.
■
Prolonged use of the optical drive,
such as watching a DVD movie, will
substantially reduce your battery life if
no other power source is attached.
■
CD-ROM: A CD-ROM drive allows you to access soft-
ware, data, or audio CDs.
Install your media player software before
first using the DVD, DVD/CD-RW, or CD-
ROM media drives. Refer to the applicable
readme file on the Driver Applications CD-
ROM.
LOADING MEDIA ON YOUR DRIVE
To load a disc into your optical drive:
1. Push and release the eject button on the front of the
optical drive to open the holder tray. The tray will
come out of the LifeBook notebook a short distance.
MEDIA PLAYER SOFTWARE
2. Gently pull the tray out until a media disc can easily
be placed in the tray.
Super-Multi DVD model only: With the Super-Multi
DVD drive and media player software you can play DVD
movies and music CDs on your LifeBook notebook. The
media player includes controls which allow you to take
full advantage of the features of a DVD movie, as well as
standard features such as fast forward, fast reverse,
pause, etc. With this drive you can also burn onto
recordable DVD-R/RW, DVD+R/RW, or CD-R/RW
discs.
There may be a protective sheet in the tray
from when it was shipped; please make
sure it is removed before operating the
drive.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 40 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
REMOVING MEDIA
■
You should periodically check the
1. Push and release the eject button on the front of
the optical drive. This will stop the drive and the
holder tray will come out of the LifeBook notebook
a short distance.
Fujitsu web site at us.fujitsu.com/
computers for current updated drivers.
All LifeBook DVD players are set to
■
play DVD titles with region code
number 1 which is specified for the
North American market. The region
number is a regional restriction code
defined by the DVD Forum acting on
Hollywood requirements. Different
region codes are recorded on video
DVD titles for publication in different
areas of the world. If the regional code
of the DVD player does not match the
regional codes on the titles, then play-
back is impossible.
2. Gently pull the tray out until the disc can easily be
removed from the tray.
3. Carefully remove the media disc from the holder
tray.
4. Gently push the holder tray back in until you
hear a click.
USING THE MEDIA PLAYER SOFTWARE
Depending upon its configuration, your
system may not have the media player
software pre-installed. If it is not installed,
reference the documentation that
■
You can change the region code on
the DVD player using the Properties
menu of the DVD software. Note,
however, that you can only change
the region code up to four times.
After the fourth change, the last
region code entered becomes perma-
nent, and cannot be changed.
accompanies the media application.
Starting a DVD Movie (DVD Models only)
1. Insert the DVD movie into the optical drive of your
notebook. If the CD AutoRun feature activates,
skip Step 2.
2a.Windows 2000 only: From the Start menu, select
Programs, then select InterVideo WINDVD and
click InterVideo WINDVD or double-click on the
InterVideo WINDVD icon on the desktop. This will
launch the DVD movie.
3. Place the media into the tray, label side up, with the
hole in the center of the disc. Snap the disc onto the
raised circle in the center of the tray.
4. Gently push the holder tray back in until you
hear a click. (Figure 4-3)
2b. Windows XP only: The first time you insert a movie
into the DVD/CD-RW tray, you will be prompted to
select what you want the system to do when discs are
inserted (e.g., start automatically or wait for a
If you have disabled the Auto Insert
Notification Function, you will have to
start the drive from your desktop, since
your LifeBook notebook will not
automatically recognize that media has
been loaded.
prompt). Until you make a selection, you will receive
the same prompt whenever you insert a disc.
3. Click OK to close the About DVD Player
Performance dialog box and the movie will begin.
Opening the Media Player Control Panel
With most DVD-ROMs, you have the option of altering
how the movie should play and what you wish to view.
You can do this by using the media player control panel
and the mouse.
(a)
(b)
1. Right-click on the movie screen to open a dropdown
menu for options.
2. Select View, then Player for all the controls available.
This will open the control panel into the bottom of
the screen.
(c)
(d)
Using the Media Player Control Panel
The media player software allows you to watch the
movie much like a VCR player. You can pause, rewind,
fast-forward and stop the movie at any point.
Figure 4-3. Loading/Ejecting Media
1. To Pause the movie, click the on-screenꢀ button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 41 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
2. To Rewind the movie, click the ꢁ button to rewind
to a specific portion of the movie, or the ꢂ button
to return to the opening screen.
an additional, charged battery or attach AC power during
the movie to view it in its entirety.
■
Prolonged use of the optical drive, such
3. To Fast-forward the movie, click the ꢃ button to
forward to a specific portion of the movie, or theꢄ
button to jump to the ending credits.
as watching a DVD movie, will greatly
reduce your notebook’s battery life.
Many movie run-times are longer than
■
4. To Stop the movie, click the ꢅ button.
your system can support on a single
battery. If you are watching a DVD
movie on battery power you may need
to swap in an additional, charged
battery or attach AC power during the
movie to view it in its entirety.
Exiting the Media Player
1. Click the U located in the upper right corner of the
title bar. This will open a media player dialog box.
2. Click Yes to stop and exit the movie, or No to close
the media player dialog box and return to the movie.
■
An additional fully-charged battery is
highly recommended if you will be
watching DVD movies on battery
power. If you don’t have an additional
battery, you may purchase one either
online at us.fujitsu.com/computers or
by calling 1-877-372-3473.
USING DOLBY™ HEADPHONE
The Dolby Headphone utility lets you enjoy multi-
channel sound sources with realistic surround sound
using your conventional stereo headphones.
Dolby Headphone is a signal processing system that
enables your stereo headphones to realistically portray
the sound of a five-speaker playback system.
To Watch a Movie on Battery Power:
1. Have an additional full-charged battery or your AC
adapter ready for use.
■
Media discs which do not have the
2. Start watching your DVD movie.
Dolby Surround 5:1 symbol will not
support Dolby Headphone.
After making changes to the Dolby
3. When the low battery warning occurs, immediately
stop the movie and exit the media player.
■
Headphone feature and clicking OK,
wait at least ten seconds before making
another change in order to allow the
system to stabilize.
If you do not stop the media player quickly
and the LifeBook notebook attempts to
auto-suspend (critical battery low state)
the LifeBook notebook will shut down
improperly. If this occurs, you will need to
perform a hard reset and follow the
instruction, if any, presented to you before
the system will reboot.
To use the Dolby Headphone feature, perform the
following steps:
1. Insert the disc in the media player tray. When you do
so, WinDVD will start automatically.
4. Power down your LifeBook notebook and replace
the discharged battery with an additional fully-
charged battery. If you do not have an additional
battery, you may attach AC power as soon as you see
the low battery warning.
2. Click on the Fujitsu logo on the WinDVD control
panel. If the disc supports Dolby Surround 5.1, a
drop down menu appears.
3. Verify that Dolby headphones is checked on the
menu. If you do not want it active, select Disable.
5. Resume your LifeBook notebook by pressing the
Suspend button again. This is not required if you
attached AC power without entering suspend mode.
USING MEDIA PLAYER ON BATTERY POWER
Since optical drives consume a lot of power, your overall
battery life will be significantly shorter when operating
the optical drive continuously (such as watching a DVD
movie) than during standard operation. Many movies
run-times are longer than your LifeBook notebook can
support on a single charged battery. If you are watching a
DVD movie on battery power you may need to swap in
6. Restart your media player, locate and skip to the
chapter of the movie you were last watching.
7. Continue watching your DVD movie.
Some shorter DVD movies may not require
you to swap batteries or attach AC power
to complete them. However, it is best to
be prepared since actual battery life while
operating the optical drive cannot be
guaranteed.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 42 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Eject Button
Figure 4-4.Loading/Ejecting a 3.5” Floppy Disk
External USB
If you eject the disk while the Floppy Disk
Drive Access indicator is active, there is a
risk of damaging the data on the disk, the
disk itself or even the disk drive.
Floppy Disk Drive
An external USB floppy disk drive is available as an
option for your LifeBook notebook. The external floppy
disk drive can read and write information on removable
1.44MB and 720KB floppy disks.
PREPARING A DISK FOR USE
Before you can use a new disk, it needs to be prepared
so your LifeBook notebook knows where to store infor-
mation. This preparation is called formatting or initial-
izing a disk. You will need to format new disks, unless
they are preformatted. (Please refer to your operating
system manual for step-by-step instructions on formatting a
disk)
Your LifeBook notebook is preconfigured
to boot from a USB floppy drive. Refer-
ence the BIOS manual for further informa-
tion on changing the default boot drive.
The BIOS manual can be found on the
Fujitsu Computer Systems web site:
us.fujitsu.com/computers, under Support.
To prevent accidental erasure of the data stored on a
disk, slide the “write protect” tab until a small hole is
exposed. This sets the disk into a protected state where
nothing can be added or removed. If you want to add or
remove data on a protected disk, slide the “write
protect” tab to close the small hole. (Figure 4-5)
LOADING A DISK
To load a disk into your disk drive, follow these easy
steps:
1. Orient the disk so that its label is facing upwards
and the shutter side is pointing towards the drive.
(Figure 4-4)
2. Push the disk into the drive until the Eject button
pops out and you hear a click.
Write Enabled
When there is no disk in the drive, the
Eject button is flush with your notebook.
Write Protected
EJECTING A DISK
To eject a disk from the disk drive, follow these easy
steps:
Figure 4-5. Floppy Disk Write Protect
1. Check that the Floppy Disk Drive Access indicator
is inactive.
Formatting a floppy disk that already con-
tains data will erase all of the information
on the disk.
2. Press the Eject button. This will push your disk
partially out of the drive.
3. Remove the disk.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 43 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
PC Card Slots
PC Card
Eject Button
Figure 4-6. Installing/Removing PC Cards
3. Insert your PC Card into the slot, with the product
PC Cards
label facing up.
Your Fujitsu LifeBook notebook supports two Type I or
Type II PC Cards or one Type III PC Card, which can
perform a variety of functions.
4. Push the card into the slot firmly until it is seated
in the opening. You will hear a click and the Eject
button will pop away from your notebook.
5. Flip the Eject button towards the rear of your
notebook to lock the PC Card.
Some available PC Cards:
■
4-in-1 media card adapter
Compact Flash media card adapter
Fax/data modem cards
Local area network (LAN) cards
IDE solid-state disk cards
SCSI cards
Smart Card holder
Other PC Cards that conform to PCMCIA 2.1 or
■
REMOVING PC CARDS
To remove a PC Card, follow these easy steps:
■
■
■
Windows has a shutdown procedure for
PC Cards that must be followed before
removing a card. (Please review your oper-
ating system manual for the correct proce-
dure). Before removing a PC Card in
■
■
■
CardBus standards
Windows 2000 Professional, shut down
PC Card operation using the Unplug/Eject
Hardware icon located on the taskbar.
For further information, refer to the instructions
supplied with your PC Card.
INSTALLING PC CARDS
PC Cards are installed in the PC Card slot. To install a
PC Card, follow these easy steps: (Figure 4-6)
1. See your PC Card manual for specific instructions
on removing your card. Some PC Cards may require
your notebook to be in Suspend Mode or Off while
removing them.
■
Installing or removing a PC Card during
your LifeBook notebook’s shutdown or
bootup process may damage the card
and/or your notebook.
If the dialog box states that the device
cannot be removed, you must save all of
your open files, close any open applica-
tions and shut down your notebook.
■
Do not insert a PC Card into a slot if
there is water or any other substance on
the card as you may permanently dam-
age the card, your LifeBook notebook,
or both.
2. Flip the Eject button towards the front of your note-
book until it is fully extended, and then push it in
until it is flush with the notebook. This will push the
PC Card slightly out of the slot allowing you to
remove the card.
■
Be sure to orient the card properly
before inserting it. Failure to do so could
result in damage to the card socket.
1. See your PC Card manual for specific instructions
on the installation of your card. Some PC Cards
may require your notebook to be Off while
installing them.
If the PC Card has an external connector
and cable, do not pull the cable when
removing the card.
2. Make sure there is no PC Card currently in the slot.
If there is, see Removing PC Cards.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 44 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
SMART CARD READER
An embedded Smart Card Reader is provided on your
LifeBook notebook. Smart Cards are the same size and
shape as credit cards, but they contain an integrated
microprocessor chip. The chip can hold a variety of
different information, and provides the user with many
possible options, such as allowing them to make secure
purchases, pay for phone calls, store security informa-
tion, and provide personal identification and informa-
tion.
In order to use the embedded Smart Card Reader, you
must purchase an optional Smart Card adapter and
third-party software for installation into an available
Type II PC Card slot.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 45 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
Memory Upgrade Module
Your Fujitsu LifeBook notebook comes with a minimum
of 256 MB of high speed Double Data Rate Synchronous
Dynamic RAM (DDR 333 SDRAM) factory installed. To
increase your LifeBook notebook’s memory capacity, you
may install an additional memory upgrade module. The
memory upgrade must be a dual-in-line (DIMM)
SDRAM module. To ensure 100% compatibility,
purchase the SDRAM module only from the Fujitsu web
store at us.fujitsu.com/computers.
Figure 4-8. Installing a Second Memory Module
8. Replace the cover.(Figure 4-9)
■
Do not remove any screws from the
9. Replace the screws.
memory upgrade module compartment
except the ones specifically shown in the
directions for installing and removing the
memory upgrade module.
■
The memory upgrade module can be
severely damaged by electrostatic dis-
charge (ESD). Be sure you are properly
grounded when handling and installing
the module.
INSTALLING MEMORY UPGRADE MODULES
1. Turn off power to your LifeBook notebook, remove
any power adapter (AC or auto/airline), and remove
the battery pack.
Figure 4-9. Replacing the Memory Compartment Cover
The memory upgrade module is not
something you routinely remove from
your notebook. Once it is installed, you
can leave it in place unless you want to
change system memory capacity.
2. Make sure that all the connector covers are closed.
3. Turn the notebook bottom side up, and remove the
screws of the memory upgrade module compart-
ment. (Figure 4-7)
4. Remove the cover.
TO REMOVE A MEMORY UPGRADE MODULE
1. Perform steps 1 through 4 of Installing a Memory
Upgrade Module.
2. Pull the clips sideways away from each side of the
memory upgrade module at the same time.
3. While holding the clips out, remove the module
from the slot by lifting it up and pulling towards the
rear of your notebook. (Figure 4-10)
Figure 4-7. Opening the Memory Upgrade Compartment
5. Remove the memory upgrade module from the
static guarded sleeve.
6. Align the memory upgrade module with the part
side up. Align the connector edge of the memory
upgrade module with the connector slot in the
compartment.
Figure 4-10. Removing a Memory Upgrade Module
7. Insert the memory upgrade module at a 45° angle.
Press the connector edge of the module firmly down
and into the connector until it lodges under the
retaining clip. You will hear a click when it is prop-
erly in place. (Figure 4-8)
4. Store the memory upgrade module in a static
guarded sleeve.
5. Replace the cover. (Figure 4-9)
6. Replace the screws.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 46 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
performance. Up to 64 MB of memory is dynamically
shared on an as-needed basis using Dynamic Video
Memory Technology (DVMT).
CHECKING THE MEMORY CAPACITY
Once you have changed the system memory capacity by
replacing the installed module with a larger one, be sure
to check that your notebook has recognized the change.
If the total memory displayed is incorrect,
check that your memory upgrade module
is properly installed. (If the module is
properly installed and the capacity is still
not correctly recognized, see Trouble-
shooting on page 55.
Check the memory capacity by clicking [Start] ->
Settings -> Control Panel, then double-clicking the
System icon. Select the General tab and check the
amount of memory under “Computer:”.
There may be a variation between the actual memory
size and what is displayed. This is due to the fact that
your system uses a video graphics chip which dynami-
cally allocates system memory to accelerate graphics
46
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 47 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
Power On/Suspend/Resume Button
Anti-theft Lock Slot
USB Ports
PS/2 Port
Parallel Port
DC
Power
Jack
External Monitor Port
DVI-D Port
Serial Port
LAN (RJ-45)Port
Figure 4-11. Port Replicator back panel
External Monitor Port
The external monitor port allows you to connect an
external VGA or SVGA CRT monitor.
Port Replicator
An optional port replicator is available for your Fujitsu
LifeBook notebook. The port replicator extends the
functionality of your notebook by providing ports to
connect PS/2 devices, a LAN (RJ-45) cable, USB devices,
an external monitor, a parallel device, a digital video
device, and a serial device. The port replicator connects
to the bottom of your notebook. (See Device Ports on
page 50 for more information)
Parallel Port
The parallel port allows you to connect parallel devices.
(This is sometimes referred to as an LPT port.)
Serial Port
The serial port allows you to connect serial (RS-232C)
devices. (This is sometimes referred to as a COM port.)
DC Power Jack
BACK PANEL COMPONENTS
The following is a brief description of the port repli-
cator’s back panel components. (Figure 4-11)
The DC power jack allows you to plug in the AC adapter
or the optional Auto/Airline adapter to power your note-
book.
LAN (RJ-45) Jack
Anti-theft Lock Slot
The LAN port allows you to connect a LAN (RJ-45)
cable. Note that when your notebook is connected to the
port replicator, the LAN port on the system is not acces-
sible; the port replicator LAN port is the only one that
can be used when it as attached to the system.
The anti-theft lock slot allows you to lock the computer
into the port replicator or to secure the port replicator
alone.
Power On/Suspend/Resume Button
The power on/suspend/resume button allows you to
poer on or suspend/resume your system via the port
replicator.
PS/2 Keyboard/Mouse Port
The PS/2 keyboard/mouse port allows you to connect
external PS/2 devices such as an external PS/2 keyboard
or mouse.
Digital Video Interface (DVI-D)
The DVI-D port allows you to connect a flat-panel LCD
monitor or television that is equipped with a DVI-D
port for ultra-crisp digital images and graphics.
USB Ports
There are four USB 2.0 ports on the port replicator. USB
2.0 ports allow you to connect any USB 2.0 device for up
to 480 Mbps transfer rate. USB 2.0 is backward-compat-
ible with USB 1.1 devices.
Port Replicator Release Button
Slide the port replicator release button to remove the
port replicator from your notebook.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 48 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Port Replicator Release Button
Anti-theft
Lock Slot
Interface
Connector
Headphone
Jack
Microphone Jack
Adjustable Guide Bar
Figure 4-12. Port Replicator front panel
To attach the port replicator, follow these easy steps:
FRONT PANEL COMPONENTS
The following is a brief description of the optional Port
Replicator’s front panel components.
1. Unplug the AC adapter from the system if it is con-
nected.
Interface Connector
The interface connector connects the optional port
replicator to your notebook.
2. Depending upon the configuration of your system,
you may need to change the position of the adjust-
able guide bar. Note the location of the interface
port on the bottom of your LifeBook:
Adjustable Guide Bar
The adjustable guide bar allows you to use the port repli-
■
If the interface port is approximately an inch
cator with different LifeBook models.
from the edge of the system, swing the guide bar
backwards until it rests atop the port replicator
base.
Microphone Jack
The microphone jack allows you to attach an external
■
microphone via the port replicator.
If the interface port is approximately two inches
away from the edge of the system, swing the guide
bar forward until it snaps into place inside the
positioners. (See the grey arrow in Figure 2).
Headphone Jack
The headphone jack allows you to connect headphones
to the port replicator.
3. Center your notebook over the port replicator so
that the interface connector on the lower surface of
your notebook aligns with the connector on top of
the port replicator (Figure 4-13).
Anti-theft Lock Slot
The anti-theft lock slot allows you to secure the port
replicator with an optional security lock/cable.
4. Push your notebook down to connect it securely to
the port replicator.
Do not hold the system by the port
replicator. The port replicator and/or the
system could be damaged if the port
replicator is used as a handle.
5. Plug the AC adapter into the DC power jack and
plug the other end into a power outlet.
ATTACHING THE PORT REPLICATOR
The port replicator can be attached to your notebook
while the power is on, while in suspend mode, or while
the power is off.
The AC adapter must be plugged into the
port replicator in order to use all of the
ports. If the adapter is connected to the
system, the USB and PS/2 ports on the port
replicator will not be usable.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 49 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
DETACHING THE PORT REPLICATOR
The optional port replicator can be detached from your
notebook while the power is on, while in suspend mode,
or while the power is off. To detach the port replicator
follow these easy steps:
1. Unlock the anti-theft lock if the system is locked into
place.
2. Press the port replicator release button to release the
system from the port replicator.
3. While holding the port replicator release button
down, lift your notebook to detach it from the port
replicator.
Figure 4-13. Attaching the Port Replicator
LOCKING THE PORT REPLICATOR
There are two anti-theft lock slots on the port replicator:
one on the back (Figure 4-11) and one on the end
(Figure 4-12). Either slot can be used to secure the port
replicator alone. The anti-theft lock slot on the back of
the port replicator can also be used to lock the system
into the port replicator.
Follow the instructions that came with the lock/cable
device for information on its use.
To lock the system to the port replicator:
1. Install the system onto the port replicator as detailed
in “Attaching the Port Replicator”.
2. Slide the anti-theft lock slot on the rear of the port
replicator all the way to the left to lock the system
into place (Figure 4-14).
3. Secure the lock per the instructions that came with
the locking device. Until it is unlocked, the system
and port replicator are locked together.
Lock
Unlock
Figure 4-14. Locking the Port Replicator
49
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 50 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Device Ports
Your Fujitsu LifeBook notebook and the optional Port
Replicator come equipped with multiple ports to which
you can connect external devices including: disk drives,
keyboards, modems, printers, etc.
■
The internal modem is designed to the
ITU-T V.90 standard. Its maximum
speed of 53000bps is the highest
allowed by FCC, and its actual connec-
tion rate depends on the line conditions.
The maximum speed is 33600bps at
upload.
MODEM (RJ-11) TELEPHONE JACK
The modem (RJ-11) telephone jack is used for an
internal modem. To connect the telephone cable follow
these easy steps:
■
The internal modem on all Fujitsu Life-
Book notebooks from Fujitsu are certi-
fied for use in the United States and
Canada. The modem may be certified in
other countries.
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Plug the other end of the telephone cable into a
telephone outlet. (Figure 4-15)
INTERNAL LAN (RJ-45) JACK
The internal LAN (RJ-45) jack is used for a Gigabit
(10Base-T/100Base-Tx/1000Base-T/Tx) Ethernet LAN
connection. You may need to configure your notebook
to work with your particular network. (Please refer to
your network administrator for information on your
network configuration.) To connect the LAN cable
follow these easy steps:
1. Align the connector with the port opening.
2. Push the connector into the port until it is
seated.(Figure 4-16)
3. Plug the other end of the cable into a LAN outlet.
Figure 4-15. Connecting a Modem
The modem sound is deactivated by default, to activate
modem sound follow these easy steps:
1. Right click on the Speaker icon in your system tray.
2. Select Open Volume.
3. Select Option/Properties.
4. Under “Show the following volume controls”, click
on Phone and click OK.
Figure 4-16. Connecting the LAN
5. Uncheck the Mute box under Phone Balance.
PARALLEL PORT
The internal modem is not intended for
use with Digital PBX systems. Do not con-
nect the internal modem to a Digital PBX
as it may cause serious damage to the
internal modem or your entire LifeBook
notebook. Consult your PBX manufac-
turer’s documentation for details. Some
hotels have Digital PBX systems. Be sure to
find out BEFORE you connect your
modem.
The parallel port, or LPT port, located on the optional
Port Replicator allows you to connect parallel devices,
such as a printer to your notebook. In order to connect a
parallel interface device follow these easy steps:
1. Align the connector with the port opening.
2. Push the connector into the port until it is
seated.(Figure 4-17)
3. Tighten the two hold-down screws, located on each
end of the connector.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 51 Thursday, February 19, 2004 4:52 PM
U s e r I n s t a l l a b l e F e a t u r e s
UNIVERSAL SERIAL BUS PORTS
The Universal Serial Bus 2.0 ports (USB) allow you to
connect USB devices such as external game pads,
pointing devices, keyboards and/or speakers.
In order to connect a USB device follow these steps:
1. Align the connector with the port opening.(Figure 4-
19)
2. Push the connector into the port until it is seated.
Figure 4-17. Connecting a Parallel Device to Port Replicator
Due to the ongoing changes in USB tech-
nology and standards, not all USB devices
and/or drivers are guaranteed to work.
SERIAL PORT
The serial port, or COM port, located on the optional
Port Replicator allows you to connect serial devices, such
as printers or scanners. In order to connect a serial inter-
face device follow these easy steps:
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on each
end of the connector.
PS/2 PORT
The PS/2 port located on the optional Port Replicator
allow you to connect an external keyboard or mouse. In
order to connect a PS/2 interface device follow these easy
steps:
Figure 4-19. Connecting a USB Device
INFRARED PORT
The Infrared IrDA (4Mbps) port allows for wireless data
transfer between your notebook and other IrDA-
compatible devices, such as another computer or a
printer, without the use of a cable. (See figure 2-6 on
page 9 for location)
1. Align the connector with the port opening.(Figure 4-
18)
2. Push the connector into the port until it is seated.
A mouse or keyboard may be installed and
automatically recognized by your note-
book without restarting or changing set-
ups.
It is important to keep in mind that while carrying out
this form of communication, both devices must be
placed so their infrared ports are directly facing each
other without obstruction. The devices must also be
separated by at least 6" but no more than 36" for
maximum performance.
The following conditions may interfere with infrared
communications:
■
A television, radio remote control unit, or a wireless
headphone is being used nearby.
■
Direct sunlight, fluorescent light, or incandescent light
shines directly on the port.
Figure 4-18. Connecting a PS/2 Device
■
Do not move either device while com-
munication is active as it may interrupt
data transmission.
DOCKING PORT
The docking port is used for the connection of your
notebook to an optional port replicator or docking
station. In order to connect your notebook to one of
these devices follow the instructions that came with your
docking port. (See figure 2-7 on page 10 for location)
■
Be careful not to scratch the infrared
port lens. Dirt, scratches, or other sur-
face marks can degrade operation.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 52 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
STEREO LINE-IN JACK
HEADPHONE JACK
The stereo line-in jack allows you to connect an external
audio source to your notebook, such as an audio cassette
player. Your audio device must be equipped with a 1/8"
(3.5 mm) stereo mini-plug in order to fit into the stereo
line-in jack of your notebook. In order to connect a
external audio source follow these easy steps: (See
figure 2-6 on page 9 for location)
The headphone jack allows you to connect headphones
or powered external speakers to your notebook. Your
headphones or speakers must be equipped with a 1/8”
(3.5 mm) stereo mini-plug. In order to connect head-
phones or speakers follow these easy steps: (See figure 2-5
on page 8 for location)
1. Align the connector with the port opening.
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
2. Push the connector into the port until it is seated.
If you plug headphones into the head-
phone jack, the built-in stereo speakers
will be disabled.
Turn down the audio volume when con-
necting electronic devices to the line-in
jack. The internal speakers might break if
unexpected large sounds
are inputted.
MICROPHONE JACK
The microphone jack allows you to connect an external
mono microphone. Your microphone must be equipped
with a 1/8”(3.5 mm) mono mini-plug in order to fit into
the microphone jack of your notebook. In order to
connect a microphone follow these easy steps: (See
figure on page 7 for location)
The stereo line-in jack will not support an
external microphone.
IEEE 1394 PORT
1. Align the connector with the port opening.
The 4-pin 1394 port allows you to connect digital
devices that are compliant with IEEE 1394 standard. The
IEEE 1394 standard is easy to use, connect, and discon-
nect. This port can allow up to 400 Mbps transfer rate. A
third-party application may be required to operate your
digital device with the 1394 port.
2. Push the connector into the port until it is seated.
EXTERNAL MONITOR PORT
The external monitor port allows you to connect an
external monitor. In order to connect an external monitor
follow these easy steps: (See figure 2-6 on page 9 for loca-
tion)
The 1394 port used in this system uses a
four-pin configuration. If you intend to
interface with devices which use a six-pin
configuration, you will need to purchase
an adapter.
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on
each end of the connector.
In order to connect a 1394 device, follow these steps:
1. Align the connector with the port opening.
Pressing the [Fn] + [F10] keys allows you
to change your selection of where to send
your display video. Each time you press the
key combination, you will step to the next
choice, starting with the built-in display
panel only, moving to the external monitor
only, finally moving to both the built-in
display panel and an external monitor.
2. Push the connector into the port until it is
seated.(Figure 4-20)
Figure 4-20. Connecting an IEEE 1394 Device
52
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 53 Thursday, February 19, 2004 4:52 PM
5
Troubleshooting
53
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 54 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
54
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 55 Thursday, February 19, 2004 4:52 PM
T r o u b l e s h o o t i n g
Troubleshooting
Your Fujitsu LifeBook notebook is sturdy and subject to
few problems in the field. However, you may encounter
simple setup or operating problems that you can solve
on the spot, or problems with peripheral devices, that
you can solve by replacing the device. The information
in this section helps you isolate and resolve some of these
straightforward problems and identify failures that
require service.
8. If you have tried the solutions suggested in the Trou-
bleshooting Table without success, contact your
support representative:
Toll free: 1-800-8Fujitsu (1-800-838-5487)
E-mail: 8fujitsu@us.fujitsu.com
Web site: us.fujitsu.com/computers.
Before you place the call, you should have the following
information ready so that the customer support represen-
tative can provide you with the fastest possible solution:
IDENTIFYING THE PROBLEM
If you encounter a problem, go through the following
procedure before pursuing complex troubleshooting:
■
Product name
Product configuration number
Product serial number
■
■
1. Turn off your LifeBook notebook.
■
■
■
■
■
Purchase date
2. Make sure the AC adapter is plugged into your note-
book and to an active AC power source.
Conditions under which the problem occurred
Any error messages that have occurred
Hardware configuration
3. Make sure that any card installed in the PC Card slot
is seated properly. You can also remove the card
from the slot, thus eliminating it as a possible cause
of failure.
Type of device connected, if any
See the Configuration Label on the bottom of your
notebook for configuration and serial numbers. (See
figure 2-7 on page 10 for location)
4. Make sure that any devices connected to the external
connectors are plugged in properly. You can also
disconnect such devices, thus eliminating them as
possible causes of failure.
SPECIFIC PROBLEMS
Using the Troubleshooting Table
5. Turn on your notebook. Make sure it has been off at
least 10 seconds before you turn it back on.
When you have problems with your LifeBook notebook,
try to find the symptoms under the Problem column of
the troubleshooting table for the feature giving you
difficulty. You will find a description of common causes
for that symptom under the column Possible Cause and
what, if anything, you can do to correct the condition
under Possible Solutions. All possible causes or solutions
may not apply to your notebook.
6. Go through the boot sequence.
7. If the problem has not been resolved, refer to the
Troubleshooting Table, that follows, for more
detailed troubleshooting information.
If you keep notes about what you have
tried, your support representative may be
able to help you more quickly by giving
additional suggestions over the phone.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 56 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
TROUBLESHOOTING TABLE
Problem
Problem
Page
Page
Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 58
Parallel, Serial and USB Device Problems . . . . . page 58
PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 59
Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 59
Shutdown and Startup Problems . . . . . . . . . . . . page 61
Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 62
Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 63
Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 56
DVD/CD-ROM Drive Problems. . . . . . . . . . . . . page 56
Port Replicator Problems. . . . . . . . . . . . . . . . . . . page 57
Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 57
Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 57
Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 58
Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 58
Problem
Possible Cause
Possible Solutions
Audio Problems
There is no sound coming
from the built-in speakers.
The volume is turned too low. Adjust the volume control on your notebook.
The software volume control is Adjust the sound volume control settings in your
set too low.
software, operating system and applications.
Headphones are plugged into
your notebook.
Plugging in headphones disables the built-in
speakers, remove the headphones.
BIOS audio settings
are incorrect.
Set the BIOS setup utility to the default values within
the Multimedia Device Configuration menu. (See
BIOS Setup Utility on page 29 for more information)
Software driver is not
configured correctly.
Refer to your application and operating system
documentation for help.
The speakers have been muted Click on the Volume icon in the tool tray on the
using the Volume icon in the
system tray.
bottom right of the screen. (It looks like a speaker).
If the Mute box is checked, click on it to uncheck it.
DVD/CD-RW/CD-ROM Drive Problems
LifeBook notebook fails to Protective sheet is still in the
Replace DVD/CD-RW/CD-ROM in tray.
recognize DVD/CD-RW/
CD-ROM’s.
DVD/CD-RW/CD-ROM
drive tray.
DVD/CD-RW/CD-ROM is
not pushed down onto raised
center circle of the drive.
Open DVD/CD-RW/CD-ROM tray and re-install
DVD/CD-RW/CD-ROM properly.
DVD/CD-RW/CD-ROM tray Push on the front of the DVD/CD-RW/CD-ROM
is not latched shut.
tray until it latches.
Incorrect DVD Player or no
DVD Player software is
installed.
Install DVD Player software. (See “Media Player
Software” on page 39 for more information.)
Wrong drive designator was
used for DVD/CD-RW/CD-
ROM in the application.
Verify the drive designator used by the application is
the same as the one used by the operating system.
When the operating system is booted from a DVD/
CD, drive designations are automatically adjusted.
Note that the drive designation can be changed with
the Disk Management tool located at Administrative
Tools -> Computer Managenment.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 57 Thursday, February 19, 2004 4:52 PM
T r o u b l e s h o o t i n g
Problem
Possible Cause
Possible Solutions
LifeBook notebook fails to
recognize DVD/CD-RW/
CD-ROM’s (continued)
Windows DVD/CD-RW/CD-
ROM auto insertion function
is disabled.
Start the DVD/CD-RW/CD-ROM from the desktop
or application software or re-enable the Windows
DVD/CD-RW/CD-ROM auto insertion function.
LifeBook notebook fails to
recognize DVD/CD-RW/
CD-ROM’s.
DVD/CD-RW/CD-ROM is
dirty or defective.
Wipe DVD/CD-RW/CD-ROM with a non-abrasive
CD cleaning cloth and reinsert. It if still will not
work try another DVD/CD-RW/CD-ROM in
the drive.
The DVD/CD-RW/CD-
ROM Access indicator on
the Status Indicator Panel
blinks at regular intervals
when no DVD/CD-RW/
CD-ROM is in the tray or
the DVD/CD-RW/CD-
ROM drive is not installed.
The Windows DVD/CD-RW/ This is normal. However, you may disable this
CD-ROM auto insertion func- feature.
tion is active and is checking to
see if a DVD/CD-RW/CD-
ROM is ready to run.
Port Replicator Problems
Note: Be sure to power down your LifeBook notebook before adding a printer to the Port Replicator parallel port.
LifeBook notebook does
Port Replicator AC adapter is
Provide power to the Port Replicator.
not turn on when installed not plugged in.
in the optional Port
Notebook is not properly
Remove and re-dock your LifeBook notebook.
Replicator
seated in the Port Replicator.
Floppy Disk Drive Problems
You cannot access your
floppy disk.
You tried to write to a write
protected floppy disk.
Eject the floppy disk and set it to write enable.
(See Preparing a Disk for Use on page 42 for more
information)
Floppy disk is not
loaded correctly.
Eject floppy disk, check orientation and re-insert.
(See Ejecting a Disk on page 42 for more information)
The floppy disk drive may not Remove and re-install your floppy disk drive.
be properly installed.
Security is set to protect access Verify your password and security settings.
to floppy disk data.
Hard Drive Problems
You cannot access your
hard drive.
The setup utility is incorrectly Revise BIOS settings to set both Primary Master
set for your internal (Primary and Primary Slave correctly. (See BIOS Setup Utility
Master) or optional second
hard drive (Primary Slave).
on page 29 for more information)
The wrong drive designator
was used by an application
Verify drive designator used by application is in
use by the operating system. When the operating
when a bootable CD-ROM was system is booted from a CD, drive designations
used to start the notebook.
are automatically adjusted.
Security is set so your oper-
ating system cannot be started
without a password.
Verify your password and security settings.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 58 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Problem
Possible Cause
Possible Solutions
Keyboard or Mouse Problems
The built-in keyboard does The notebook has gone into
Push the Power/Suspend/Resume button.
not seem to work.
Suspend mode.
Your application has locked
out your keyboard.
Try to use your integrated pointing device to restart
your system.
You have installed an
external keyboard or
mouse, and it does not
seem to work.
Your external device is not
properly installed.
Re-install your device. (See Device Ports on page 50
for more information)
Your operating system
software is not setup with the
correct software driver
for that device.
Check your device and operating system docu-
mentation and activate the proper driver.
Your mouse or keyboard is
connected to the wrong PS/2
port on the optional Port
Replicator.
Plug the mouse into the PS/2 Mouse port and
the external keyboard or numeric key pad into the
PS/2 Keyboard port. (See PS/2 Port on page 51 for
more information)
You have connected an
external keyboard or a
mouse and it seems to be
locking up the system.
Your operating system
software is not setup with
the correct software driver
for that device.
Check your device and operating system
documentation and activate the proper driver.
Your system has crashed.
Try to restart your notebook. I
Memory Problems
Your Power On screen, or
Main menu of the BIOS
setup utility information,
does not show the correct
amount of installed
Your memory upgrade module Remove and re-install your memory upgrade
is not properly installed.
module. (See Memory Upgrade Module on page 45
for more information)
You have a memory failure.
Check for Power On Self Test (POST) messages.
(See Power On Self Test Messages on page 64 for more
information)
memory.
Modem Problems
Messages about modem
operation.
Messages about modem
operation are generated by
whichever modem application
is in use.
See your application software documentation for
additional information.
Parallel, Serial, and USB Device Problems
You have installed a parallel The device is not
Remove and re-install the device. (See Device Ports
port device, a serial port
device or a USB device.
Your LifeBook notebook
does not recognize the
device, or the device does
not seem to work properly.
properly installed.
on page 50 for more information)
The device may have been
Close the application and restart your notebook.
installed while an application
was running, so your notebook
is not aware of its installation.
Your device may not have the
correct software driver active.
See your software documentation and activate the
correct driver.
You may have the wrong I/O
address selected for your
device.
See your device documentation and software docu-
mentation to determine the required I/O address.
Change the settings in the BIOS setup utility. (See
BIOS Setup Utility on page 29 for more information)
58
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 59 Thursday, February 19, 2004 4:52 PM
T r o u b l e s h o o t i n g
Problem
Possible Cause
Possible Solutions
You have installed a parallel Your device and another device Check all I/O addresses located within the BIOS
port device, a serial port
device or a USB device.
Your LifeBook notebook
does not recognize the
device, or the device does
not seem to work properly.
are assigned the same I/O
address.
setup utility and any other installed hardware or
software to make sure there are no duplications.
Parallel port is set to output
only.
Check parallel port setting in the BIOS and set to
bi-directional or ECP.
(continued)
PC Card Problems
A card inserted in the PC
The card is not properly
Remove and re-install the card. (See PC Cards on
Card slot does not work or installed.
is locking up the system.
page 43 for more information)
The card may have been
Close the application and restart your notebook.
installed while an application
was running, so your notebook
is not aware of its installation.
Your software may not have
the correct software driver
active.
See your software documentation and activate the
correct driver.
You may have the wrong I/O
address selected for your PC
Card device.
See your PC Card documentation to determine
the required I/O address. Change the settings in
the BIOS. (See BIOS Setup Utility on page 29 for
more information)
Your PC Card device and
Check all I/O addresses located within the BIOS
another device are assigned the setup utility and any other installed hardware or
same I/O address.
software to make sure there are no duplications.
Power Failures
You turn on your
The installed primary battery
Check the Status Indicator Panel to determine the
LifeBook notebook and
nothing seems to happen.
is completely discharged, there presence and condition of the batteries. (See Status
is no optional second battery
installed or there is no Power
adapter (AC or Auto/Airline)
installed.
Indicator Panel on page 11 for more information)
Install a charged battery or a Power adapter.
The primary battery is
installed but is faulty.
Use the Status Indicator panel to verify the presence
and condition of the batteries. (See Status Indicator
Panel on page 11 for more information) If a battery is
indicating a short, remove that battery and operate
from another power source or replace that battery.
The battery or batteries are low. Check the Status Indicator Panel to determine the
presence and condition of the batteries. (See Status
Indicator Panel on page 11 for more information) Use
a Power adapter to operate until a battery is charged
or install a charged battery.
The power adapter (AC or
auto/airline) is not plugged
in properly.
Verify that your adapter is connected correctly. (See
Power Sources on page 27 for more information)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 60 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Problem
Possible Cause
Possible Solutions
You turn on your
LifeBook notebook and
nothing seems to happen.
The Power adapter (AC or
auto/airline) has no power
from the AC outlet, airplane
Move the AC cord to a different outlet, check for
a line switch or tripped circuit breaker for the AC
outlet. If you are using an auto/airline adapter in
seat jack, or the car’s cigarette a car make sure the ignition switch is in the On or
(continued)
lighter.
Accessories position.
The Power adapter (AC or
auto/airline) is faulty.
Try a different Power adapter or install a charged
optional second battery.
Your LifeBook notebook
turns off all by itself.
The power management
parameters are set for auto
timeouts which are too short
for your operating needs.
Press any button on the keyboard, or move the
mouse to restore operation. If that fails, push the
Power/Suspend/Resume button. Check your power
management settings, or close your applications and
go to the Power Savings menu of the setup utility to
adjust the timeout values to better suit your needs.
You are operating on battery
Install a power adapter and then push the Power/
power only and have ignored a Suspend/Resume button. (See Power Sources on
low battery alarm until the
batteries are all at the dead
battery state and your machine
has gone into Dead Battery
Suspend mode.
page 27 for more information)
You have a battery failure.
Verify the condition of the batteries using the
Status Indicator panel, and replace or remove
any batteries that are shorted. (See Status Indicator
Panel on page 11 for more information)
Your power adapter has failed Make sure the adapter is plugged in and the outlet
or lost its power source.
has power.
Your LifeBook notebook
will not work on battery
alone.
The installed batteries
are dead.
Replace the battery with a charged one or install
a Power adapter.
No batteries are installed.
Install a charged battery.
The batteries are improperly
installed.
Verify that the batteries are properly connected
by re-installing them.
Your installed batteries
are faulty.
Verify the condition of the batteries using the
Status Indicator panel and replace or remove
any batteries that are shorted. (See Status Indicator
Panel on page 11 for more information)
The batteries seem to
discharge too quickly.
You are running an application Use both the primary battery and an optional
that uses a great deal of power second battery and/or use a power adapter for this
due to frequent hard drive
access or DVD/CD-ROM
access, use of a modem card
or a LAN PC card.
application when at all possible.
The power savings features
may be disabled.
Check the power management and/or setup utility
settings in the Power Savings menu and adjust
according to your operating needs.
The brightness is turned all
the way up.
Turn down the brightness adjustment. The higher
the brightness the more power your display uses.
The batteries are very old.
Replace the batteries.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 61 Thursday, February 19, 2004 4:52 PM
T r o u b l e s h o o t i n g
Problem
Possible Cause
Possible Solutions
The batteries seem to
discharge too quickly.
The batteries have been
exposed to high temperatures.
Replace the batteries.
(continued
The batteries are too hot
or too cold.
Restore the notebook to normal operating tempera-
ture. The Charging icon on the Status Indicator
panel will flash when the battery is outside its
operating range.
Shutdown and Startup Problems
The Suspend/Resume
button does not work.
The Suspend/Resume button
Enable the button from the setup utility.
is disabled from the Advanced
submenu of the Power menu
of the setup utility.
You did not hold the button
in long enough.
Hold the button longer. This may need to be a few
seconds if your application is preventing the CPU
from checking for button pushes.
There may be a conflict with
the application software.
Close all applications and try the button again.
The system powers up, and The boot sequence settings
displays power on informa- of the setup utility are not
Set the operating source by pressing the [ESC] key
while the Fujitsu logo is on screen or use the [F2]
key and enter the setup utility and adjust the source
settings from the Boot menu. (See BIOS Setup
Utility on page 29 for more information)
tion, but fails to load the
operating system.
compatible with your
configuration.
You have a secured system
requiring a password to load
your operating system.
Make sure you have the right password. Enter the
setup utility and verify the Security settings and
modify them as accordingly. (See BIOS Setup Utility
on page 29 for more information)
Internal hard drive was
not detected.
Use the BIOS setup utility or Primary Master
submenu, located within the Main menu, to try to
auto detect the internal hard drive.
An error message is
displayed on the screen
during the notebook
(boot) sequence.
Power On Self Test (POST) has See the Power On Self Test (POST) messages to
detected a problem.
determine the meaning and severity of the problem.
Not all messages are errors; some are simply status
indicators. (See Power On Self Test Messages on
page 64 for more information)
Your notebook appears to
change setup parameters
when you start it.
BIOS setup changes were not
saved when you made them
and exited the BIOS setup
utility returning it to
Make sure you select Save Changes And Exit when
exiting the BIOS setup utility.
previous settings.
The BIOS CMOS hold-up
battery has failed.
Contact your support representative for repairs.
This is not a user serviceable part but has a normal
life of 3 to 5 years.
Your system display won’t
The system may be password- Check the status indicator panel to verify that the
turn on when the system is protected.
turned on or when the
Security icon is blinking. If it is blinking, enter your
password.
system has resumed.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 62 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Problem
Possible Cause
Possible Solutions
Video Problems
The built-in display is
blank when you turn on
your LifeBook notebook.
Something is pushing on the
Closed Cover switch.
Clear the Closed Cover switch. (See figure 2-3 on
page 6 for location)
The notebook is set for an
external monitor only.
Pressing [F10] while holding down the [Fn] key
allows you to change your selection of where to
send your display video. Each time you press the
combination of keys you will step to the next
choice. The choices, in order are: built-in display
only, external monitor only, both built-in display
and external monitor.
The angle of the display and
Move the display and the brightness control until
the brightness settings are not you have adequate visibility.
adequate for your lighting
conditions.
The power management time- Press any button the keyboard, or move the mouse
outs may be set for very short
intervals and you failed to
notice the display come on
and go off again.
to restore operation. If that fails, push the Power/
Suspend/Resume button. (The display may be shut
off by Standy mode, Auto Suspend or Video
Timeout)
The LifeBook notebook
turned on with a series of
beeps and your built-in
display is blank.
Power On Self Test (POST)
has detected a failure which
does not allow the display
to operate.
Contact your support representative.
The display goes blank by
itself after you have been
using it.
The notebook has gone into
Video timeout, Standby mode, mouse to restore operation. If that fails, push the
Suspend mode or Save-to-Disk Power/Suspend/Resume button. Check your power
Press any button on the keyboard, or move the
mode because you have not
used it for a period of time.
management settings, or close your applications
and go to the Power Savings menu of the setup
utility to adjust the timeout values to better suit
your operation needs. (See BIOS Setup Utility on
page 29 for more information)
The power management time- Press any button on the keyboard, or move the mouse
outs may be set for very short
intervals and you failed to
notice the display come on
and go off again.
to restore operation. If that fails, push the Power/
Suspend/Resume button. (The display may be shut
off by Standby Mode, Auto Suspend or Video
Timeout)
Something is pushing on the
Closed Cover switch.
Check the Closed Cover switch. (See figure 2-3 on
page 6 for location)
Your system display won’t
The system may be password- Check the status indicator panel to verify that the
turn on when the system is protected.
turned on or when the
Security icon is blinking. If it is blinking, enter your
password.
system has resumed.
The Built-in Display does
not close.
A foreign object, such as a
paper clip, is stuck between the
display and the keyboard.
Remove all foreign objects from the keyboard.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 63 Thursday, February 19, 2004 4:52 PM
T r o u b l e s h o o t i n g
Problem
Possible Cause
Possible Solutions
The Built-in Display has
bright or dark spots.
If the spots are very tiny and
few in number, this is normal
for a large LCD display.
This is normal; do nothing.
If the spots are numerous or
large enough to interfere with
your operation needs.
Display is faulty; contact your support representative.
The application display
uses only a portion of your that does not support 800 x
screen and is surrounded
by a dark frame.
You are running an application Display compression gives a clearer but smaller
display for applications that do not support 800 x
600/1024 x 768 pixel resolution 600/1024 x 768 pixel resolution. You can fill the
display and display compres-
sion is enabled.
screen but have less resolution by changing your
display compression setting, (See the Video Features
submenu, located within the Advanced menu of the
BIOS. (See BIOS Setup Utility on page 29 for more
information)
The Display is dark when
on battery power.
The Power Management utility Press [Fn] + [F7] to increase brightness or double-
default is set on low brightness click on the battery gauge and adjust Power Control
to conserve power.
under battery settings.
You have connected an
external monitor and
it does not display
any information.
Your BIOS setup is not set to
Try toggling the video destination by pressing [Fn]
enable your external monitor. and [F10] together, or check your BIOS setup and
enable your external monitor. (See the Video Features
submenu, located within the Advanced Menu of the
BIOS. (See BIOS Setup Utility on page 29 for more
information)
Your external monitor is not
properly installed.
Reinstall your device. (See External Monitor Port on
page 52 for more information)
Your operating system soft-
ware is not setup with the
correct software driver for
that device.
Check your device and operating system
documentation and activate the proper driver.
You have connected an
external monitor and it
does not come on.
Your external monitor is not
compatible with your LifeBook External Monitor Support portions of the
notebook.
See your monitor documentation and the
Specifications section. (See Specifications on page 77
for more information)
Miscellaneous Problems
An error message is
displayed on the screen
during the operation of
an application.
Application software often
has its own set of error
message displays.
See your application manual and help displays
screens for more information. Not all messages are
errors some may simply be status.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 64 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
*Incorrect Drive A type – run SETUP
POWER ON SELF TEST MESSAGES
Type of floppy drive A: not correctly identified in Setup.
This means that the floppy disk drive type identified in
your setup utility does not agree with the type detected
by the Power On Self Test. Run the setup utility to
correct the inconsistency.
The following is an alphabetic list of error-and-status
messages that Phoenix BIOS and/or your operating
system can generate and an explanation of each message.
Error messages are marked with an *. If an error message
is displayed that is not in this list, write it down and
check your operating system documentation both on
screen and in the manual. If you can find no reference
to the message and its meaning is not clear, contact
your support representative for assistance.
*Incorrect Drive B type – run SETUP
Type of floppy drive B: not correctly identified in Setup.
This means that the floppy disk drive type identified in
your setup utility does not agree with the type detected
by the Power On Self Test. Run the setup utility to
correct the inconsistency.
nnnn Cache SRAM Passed
Where nnnn is the amount of system cache in kilobytes
success-fully tested by the Power On Self Test. (This can
only appear if you have an SRAM PC Card installed.)
*Invalid NVRAM media type
Problem with NVRAM access. In the unlikely case that
you see this message you may have some display prob-
lems. You can continue operating but should contact
your support representative for more information.
*Diskette drive A error or Diskette drive B error
Drive A: or B: is present but fails the BIOS Power On Self
Test diskette tests. Check to see that the drive is defined
with the proper diskette type in the Setup Utility, (See
BIOS Setup Utility on page 29 for more information) and
that the diskette drive is installed correctly. If the disk
drive is properly defined and installed, avoid using it and
contact your support representative.
*Keyboard controller error
The keyboard controller test failed. You may have to
replace your keyboard or keyboard controller but may
be able to use an external keyboard until then. Contact
your support representative.
*Extended RAM Failed at offset: nnnn
*Keyboard error
Extended memory not working or not configured prop-
erly. If you have an installed memory upgrade module,
verify that the module is properly installed. If it is prop-
erly installed, you may want to check your Windows
Setup to be sure it is not using unavailable memory
until you can contact your support representative.
Keyboard not working. You may have to replace your
keyboard or keyboard controller but may be able to
use an external keyboard until then. Contact your
support representative.
*Keyboard error nn
BIOS discovered a stuck key and displays the scan code
for the stuck key. You may have to replace your keyboard
but may be able to use an external keyboard until then.
Contact your support representative.
nnnn Extended RAM Passed
Where nnnn is the amount of memory in kilobytes
successfully tested.
*Failing Bits: nnnn The hex number nnnn
*Monitor type does not match CMOS – Run SETUP
Monitor type not correctly identified in Setup. This error
probably means your BIOS is corrupted, run the setup
utility and set all settings to the default conditions. If you
still get this error, contact your support representative.
This is a map of the bits at the memory address (in
System, Extended, or Shadow memory) which failed the
memory test. Each 1 (one) in the map indicates a failed
bit. This is a serious fault that may cause you to lose data
if you continue. Contact your support representative.
*Operating system not found
*Fixed Disk x Failure or Fixed Disk Controller
Failure (where x = 1-4)
Operating system cannot be located on either drive A: or
drive C: Enter the setup utility and see if both the fixed
disk, and drive A: are properly identified and that the
boot sequence is set correctly. Unless you have changed
your installation greatly, the operating system should be
on drive C:. If the setup utility is correctly set, your hard
drive may be corrupted.
The fixed disk is not working or not configured properly.
This may mean that the hard drive type identified in
your setup utility does not agree with the type detected
by the Power On Self Test. Run the setup utility to check
for the hard drive type settings and correct them if
necessary. If the settings are OK and the message appears
when you restart the system, there may be a serious fault
which might cause you to lose data if you continue.
Contact your support representative.
*Parity Check 1 nnnn
Parity error found in the system bus. BIOS attempts
to locate the address and display it on the screen. If it
cannot locate the address, it displays ????. This is a
potentially data destroying failure. Contact your
support representative.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 65 Thursday, February 19, 2004 4:52 PM
T r o u b l e s h o o t i n g
*Parity Check 2 nnnn
nnnn System RAM Passed
Parity error found in the I/O bus. BIOS attempts to
locate the address and display it on the screen. If it
cannot locate the address, it displays ????. This is a
potentially data-destroying failure. Contact your
support representative.
Where nnnn is the amount of system memory in
kilobytes successfully tested.
*System timer error
The timer test failed. The main clock that operates the
computer is faulty. Requires repair of system board.
Contact your support representative for repairs.
*Press <F1> to resume, <F2> to SETUP
Displayed after any recoverable error message. Press
the [F1] key to continue the boot process or the [F2]
key to enter Setup and change any settings.
UMB upper limit segment address: nnnn
Displays the address of the upper limit of Upper
Memory Blocks, indicating released segments of the
BIOS memory which may be reclaimed by a virtual
memory manager.
*Previous boot incomplete –
Default configuration used
Previous Power On Self Test did not complete success-
fully. The Power On Self Test will load default values and
offer to run Setup. If the previous failure was caused by
incorrect values and they are not corrected, the next
boot will likely fail also. If using the default settings does
not allow you to complete a successful boot sequence,
you should turn off the power and contact your support
representative.
Video BIOS shadowed
Video BIOS successfully copied to shadow RAM.
EMERGENCY MEDIA PLAYER
DRIVE TRAY RELEASE
If for some reason the eject button fails, you can open
the DVD/CD-ROM tray with a paper clip or similar tool
inserted into the eject hole in the far right side of the
front of the tray. Straighten one side of a paper clip
and push it gently into the hole. The tray will pop out
a short distance.
*Real time clock error
Real-time clock fails BIOS test. May require board repair.
Contact your support representative.
*Shadow RAM Failed at offset: nnnn
MODEM RESULT CODES
Shadow RAM failed at offset nnnn of the 64k block at
which the error was detected. You are risking data corrup-
tion if you continue. Contact your support representative.
The operating system and application software that is
factory installed detects the modem characteristics and
provides the necessary command strings to operate the
modem. The internal modem operation is controlled by
generic AT commands from the operating system and
application software. The standard long form result
codes may, in some cases, be displayed on your screen to
keep you informed of the actions of your modem. The
operating system and application software may suppress
display of the result codes.
nnnn Shadow RAM Passed
Where nnnn is the amount of shadow RAM in kilobytes
successfully tested.
*System battery is dead – Replace and run SETUP
The BIOS CMOS RAM memory hold up battery is dead.
This is part of your BIOS and is a board mounted
battery which requires a support representative to
change. You can continue operating but you will have to
use setup utility default values or reconfigure your setup
utility every time you turn off your notebook. This
battery has an expected life of 2 to 3 years.
Examples of result codes are:
■
OK
■
NO CARRIER
NO DIALTONE
CONNECT 53000 (Connection complete
■
System BIOS shadowed
System BIOS copied to shadow RAM.
■
at 53,000 bps.)
ERROR
FAX
RING (This means an incoming call.)
BUSY
NO ANSWER
■
*System CMOS checksum bad – run SETUP
BIOS CMOS RAM has been corrupted or modified
incorrectly, perhaps by an application program that
changes data stored in BIOS memory. Run Setup and
reconfigure the system.
■
■
■
■
When using the internal modem with applications
that are not factory installed refer to the
application documentation.
*System RAM Failed at offset: nnnn
System memory failed at offset nnnn of in the 64k block
at which the error was detected. This means that there is
a fault in your built-in memory. If you continue to
operate, you risk corrupting your data. Contact your
support representative for repairs.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 66 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
disk. Then, in the event of a hard disk failure, you can
restore the image that includes the applications and data
RESTORING YOUR
PRE-INSTALLED SOFTWARE
files you use.
If your system was delivered with
Windows 2000 as the operating system,
the Windows 2000 image is on the D:
partition, but the Restore Disc contains
Windows XP. If you decide to restore your
system from the Restore Disc, you will
overwrite Windows 2000 with the
Windows XP operating system.
Using the DISE feature will reduce the
amount of usable disk space on your hard
disk drive.
Creating a Backup Image
You can create a backup image of your C:\ drive at any
time. The C:\ partition must be a FAT, FAT32, or NTFS
partition, and it must be directly before the backup
partition on your hard disk.
The Drivers and Applications Restore (DAR) CD
contains:
■
Sets of device drivers and Fujitsu utilities (in specific
directories) that are unique to your LifeBook note-
book configuration for use as documented below.
A link to the Drive Image Special Edition (DISE)
utility on your hard disk drive.
There are two ways to implement the DISE utility: When
booting up the system, or from the desktop.
■
Creating a backup image when booting up
Before creating a backup image at boot-up, you must
first change the boot-up priority in the BIOS so that the
system will go to the CD drive first, rather than trying to
boot-up from the hard drive or an external floppy disk
drive.
■
Read-me files that provide additional use information
for items on this CD-ROM.
If the DAR CD is in the drive when you
boot up the system, a message will appear
informing you that continuing to boot
from the CD will overwrite all information
on the hard drive, including saved files,
and restore the hard drive to its factory
configuration. If you wish to install drivers
or applications only from the CD, remove
the disk from the drive, reboot the system,
and insert the CD after Windows has
started.
To change the boot-up priority:
1. Start your system and press the [F2] key when the
Fujitsu logo appears. You will enter the BIOS Setup
Utility.
2. Using the arrow keys, go to the Boot menu.
3. Arrow down to the Boot Device Priority submenu
and press [Enter].
4. Arrow down to the CD-ROM drive in the list, and
press the space bar (or the + key) to move the CD-
ROM drive to the top of the list. (The system
attempts to boot from the devices in the order in
which they are listed.)
If you have access to the internet, visit the
Fujitsu Support web site at us.fujitsu.com/
computers to check for the most current
information, drivers and hints on how to
perform recovery and system updates.
5. Press [F10], then click on [Yes] to exit the BIOS
Setup Utility and return to the boot process.
After you have changed the boot priority, you can create
a backup image when you are booting up:
DRIVE IMAGE SPECIAL EDITION (DISE)
PowerQuest Drive Image Special Edition (DISE)
provides a way to restore your computer if you experi-
ence a hard disk crash or other system failure. Fujitsu has
used DISE to create an image of everything installed on
the computer at the time you purchased it. The image is
saved on a separate partition on the hard disk. You can
use DISE to restore the factory image and return your
computer to the state in which it was shipped from
Fujitsu.
1. Install the DAR CD in the drive prior to booting up.
When bootup begins, a message will appear
informing you that continuing to boot from the CD
will overwrite all information on the hard drive,
including saved files, and restore the hard drive to its
factory configuration.
2. When you are asked if you want to restore the
factory image, click [Y]es.
Creating a backup image from the desktop
Although it is not necessary, you can use DISE to store
additional image files that you create. For example, if
you install several applications and save data files on
your hard disk, you can create a new image file that
includes them and then save that image file on the hard
To create a backup image from the desktop, select Drive
Image SE from the Program list. You will initially be
prompted to create a backup diskette. It is not necessary
66
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 67 Thursday, February 19, 2004 4:52 PM
T r o u b l e s h o o t i n g
to create the backup diskette, since the DAR CD
performs the same function.
AUTOMATICALLY DOWNLOADING
DRIVER UPDATES
Your system has a convenient tool called the Fujitsu
Driver Update (FDU) utility. With FDU, you can choose
to automatically or manually go to the Fujitsu site to
check for new updates for your system.
1. At the Drive Image Special Edition main screen,
click Options> Create New Backup. DISE displays a
warning that it must go to DOS to create the image.
3. Click Yes.
DISE creates an image file in the backup partition. If
you created a backup image previously, the new
image overwrites the old one.
The FDU icon should appear in the system tray at the
bottom right of your screen (roll the cursor over the
icons to find the correct one). If the FDU icon does not
appear in the system tray, it can be started by going to
[Start] -> All Programs, and clicking on Fujitsu Driver
Update; this will create the icon automatically.
Enlarging the Backup Partition
If there is not enough unused space in the backup parti-
tion on your hard disk, DISE will resize the partition.
DISE will display the minimum, maximum, and recom-
mended sizes for the backup partition. You choose the
size you want.
To invoke the FDU menu, you can either right-click on
the FDU icon or hold the pen on the icon for a couple of
seconds until the menu appears. The menu contains the
following items:
DISE takes the space from the FAT, FAT32, or NTFS
partition that you are backing up. If there is not enough
unused space in that partition to take, you will not be
able to resize the backup partition and create an image
file. You can delete files from the FAT, FAT32, or NTFS
partition to create more unused space on the hard disk.
■
Check for updates now
Allows for manual driver update search. The first
time it is used, you are prompted to agree to a user
agreement. After clicking on the icon, the FDU auto-
matically connects with the Fujitsu site to check for
updates and downloads them. While downloading,
the icon has a red bar through it, indicating that it
cannot be used while the download is in process.
When the update is complete, a message appears
informing you of the fact.
Restoring a Backup Image
You can restore either a factory image or a backup image
you created. Be aware that restoring a backup image will
replace the contents of the C:\ partition with the image
you restore.
■
Enable Automatic Update Notifications
1. Disable virus protection software. If virus protection
software is enabled, DISE will hang.
Automatically searches for new updates on a regular
basis (approximately every 3 days).
2. From the DISE main window, click Options >
Restore Backup to restore an image you created, or
click Options > Restore Factory Backup to restore
the factory image.
■
Show update history
Brings up a screen that displays a history of updates
that have been made via the FDU.
■
About Fujitsu Driver Update
DISE shuts down to DOS and restores the image file.
Displays the FDU version number and copyright
information
Re-Installing Individual Drivers and Applications
The Drivers and Application CD can be used to selec-
tively re-install drivers and/or applications that may have
been un-installed or corrupted.
■
Fujitsu Driver Update Readme
Displays the FDU readme.
To re-install drivers and/or applications:
1. Boot up the system and insert the DAR CD after
Windows has started. The LifeBook Easy Installation
screen appears.
2. Select the drivers and applications you want to
install from the list that is displayed.
3. Click [Start]. Follow the prompts that appear to
complete installation of the selected drivers and/or
applications.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 68 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
68
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 69 Thursday, February 19, 2004 4:52 PM
6
Care and Maintenance
69
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 70 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
70
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 71 Thursday, February 19, 2004 4:52 PM
C a r e a n d M a i n t e n a n c e
Cleaning your LifeBook notebook
Always disconnect the power plug. (Pull the plug, not
the cord.)
Care and Maintenance
■
If you use your Fujitsu LifeBook notebook carefully, you
will increase its life and reliability. This section provides
■
Clean your LifeBook notebook with a damp, lint-free
some tips for looking after the notebook and its devices.
cloth. Do not use abrasives or solvents.
■
Use a soft cloth to remove dust from the screen.
Electrical equipment may be hazardous if
misused. Operations of this product or simi-
lar products, must always be supervised by
an adult. Do not allow children access to
the interior of any electrical products and
do not permit them to handle any cables.
Never use glass cleaners.
Storing your LifeBook notebook
If storing your notebook for a month or longer, turn
your LifeBook notebook off, fully charge the
■
battery(s), then remove and store all Lithium ion batter-
ies.
Caring for your LifeBook notebook
Your LifeBook notebook is a durable but sensitive elec-
tronic device. Treat it with respect and care.
■
■
Store your notebook and batteries separately. If you
store your LifeBook with a battery installed, the battery
will discharge, and battery life will be reduced. In addi-
tion, a faulty battery might damage your LifeBook.
■
Make a habit of transporting it in a suitable carrying
case.
■
■
Do not attempt to service the computer yourself.
Store your Fujitsu LifeBook in a cool, dry location.
Always follow installation instructions closely.
Temperatures should remain between 13ºF (-25ºC) and
140ºF (60ºC).
■
Keep it away from food and beverages.
■
If you accidentally spill liquid on your LifeBook note-
book:
Traveling with your LifeBook notebook
Do not transport your notebook while it is turned on.
■
1. Turn it off.
■
It is recommended that you carry your notebook with
you while travelling, rather than checking it in as bag-
gage.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
4. If your notebook will not boot after it has dried
out, call your support representative.
■
Always bring your System Recovery CD that came with
■
■
■
■
your notebook when you travel. If you experience sys-
tem software problems while traveling, you may need it
to correct any problems.
Do not use your Fujitsu LifeBook notebook in a wet
environment (near a bathtub, swimming pool).
Always use the AC adapter and batteries that are
approved for your notebook.
■
Never put your notebook through a metal detector.
Have your notebook hand-inspected by security per-
sonnel. You can however, put your notebook through a
properly tuned X-ray machine. To avoid problems,
place your notebook close to the entrance of the
machine and remove it as soon as possible or have your
notebook hand-inspected by security personnel. Secu-
rity officials may require you to turn your notebook
On. Make sure you have a charged battery on hand.
Avoid exposure to sand, dust and other
environmental hazards.
Do not expose your notebook to direct sunlight for long
periods of time as temperatures above 140° F (60° C)
may damage your notebook.
■
Keep the covers closed on the connectors and slots when
they are not in use.
■
When traveling with the hard drive removed, wrap the
■
■
Do not put heavy or sharp objects on the computer.
drive in a non-conducting materials (cloth or paper). If
you have the drive checked by hand, be ready to install
the drive if needed. Never put your hard drive through a
metal detector. Have your hard drive hand-inspected by
security personnel. You can however, put your hard
drive through a properly tuned X-ray machine.
If you are carrying your LifeBook notebook in a brief-
case, or any other carrying case, make sure that there are
no objects in the case pressing on the lid.
■
Never position your notebook such that the optical
drive is supporting the weight of the notebook.
■
Take the necessary plug adapters if you're traveling over-
seas. Check the following diagram to determine which
plug adapter you'll need or ask your travel agent.
■
■
Do not drop your notebook.
Do not touch the screen with any sharp objects.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 72 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
■
Disable the Media Player auto insert notification
function.
Outlet Type
Location
■
■
Always use fully charged batteries.
United States, Canada,
parts of Latin America,
Mexico, Japan, Korea,
the Philippines, Taiwan
Eject PCMCIATM cards when not in use.
FLOPPY DISKS AND DRIVES
Caring for your Floppy Disks
Avoid using the floppy disks in damp and dusty
Russia and the Commonwealth
of Independent States (CIS),
most of Europe, parts of Latin
America, the Middle East, parts
of Africa, Hong Kong, India,
most of South Asia
■
locations.
■
Never store a floppy disk near a magnet or magnetic
field.
■
Do not use a pencil or an eraser on a disk or disk label.
United Kingdom,
Ireland, Malaysia, Singapore,
parts of Africa
■
Avoid storing the floppy disks in extremely hot or cold
locations, or in locations subject to severe temperature
changes. Store at temperatures between 50º F (10ºC)
and 125ºF (52ºC).
China, Australia,
New Zealand
■
Do not touch the exposed part of the disk behind the
metal shutter.
■
Never use the floppy disk drive with any liquid, metal,
or other foreign matter inside the floppy disk drive
or disk.
BATTERIES
Caring for your Batteries
Always handle batteries carefully.
■
■
Never disassemble your floppy disk drive.
■
Do not short-circuit the battery terminals (that is, do
not touch both terminals with a metal object). Do not
carry lose batteries in a pocket or purse where they may
mix with coins, keys, or other metal objects. Doing so
may cause an explosion or fire.
MEDIA CARE
Caring for your Media (DVD/CD/CD-R)
Media discs are precision devices and will function reli-
ably if given reasonable care.
■
■
■
■
■
Always store your media disc in its case when it is not in
use.
Do not drop, puncture, disassemble, mutilate or incin-
erate the battery.
■
Always handle discs by the edges and avoid touching the
surface.
Recharge batteries only as described in this manual and
only in ventilated areas.
■
Avoid storing any media discs in extreme temperatures.
Do not leave batteries in hot locations for more than a
day or two. Intense heat can shorten battery life.
■
Do not bend media discs or set heavy objects on them.
Do not leave a battery in storage for longer than 6
months without recharging it.
■
Do not spill liquids on media discs.
■
Do not scratch media discs.
Increasing Battery Life
■
■
Do not get dust on media discs.
Power your LifeBook notebook through the AC or
optional auto/airline adapter whenever possible.
■
Never write on the label surface with a ballpoint pen or
■
pencil. Always use a felt pen.
If your notebook is running on battery power all day,
connect it to the AC adapter overnight to recharge the
battery.
■
If a media disc is subjected to a sudden change in tem-
perature, cold to warm condensation may form on the
surface. Wipe the moisture off with a clean, soft, lint
free cloth and let it dry at room temperature. DO NOT
use a hair dryer or heater to dry media discs.
■
Keep brightness to the lowest level comfortable.
■
Set the power management for maximum battery life.
■
Put your notebook in Suspend mode when it is turned
■
If a disc is dirty, use only a DVD/CD cleaner or wipe it
on and you are not actually using it.
with a clean, soft, lint free cloth starting from the inner
edge and wiping to the outer edge.
■
Limit your media drive access.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 73 Thursday, February 19, 2004 4:52 PM
C a r e a n d M a i n t e n a n c e
Caring for your Optical Drive
Your optical drive is durable but you must treat it with
care. Please pay attention to the following points:
PC CARDS
Caring for your PC Cards
PC Cards are durable, but you must treat them with
care. The documentation supplied with your PC Card
will provide specific information, but you should pay
attention to the following points:
■
The drive rotates the compact disc at a very high speed.
Do not carry it around or subject it to shock
or vibration with the power on.
■
To keep out dust and dirt, store PC Cards in their
■
Avoid using or storing the drive where it will be exposed
protective sleeves when they are not installed in your
LifeBook notebook.
to extreme temperatures.
■
Avoid using or storing the drive where it is damp or
dusty.
■
Avoid prolonged exposure to direct sunlight or
excessive heat.
■
Avoid using or storing the drive near magnets or devices
that generate strong magnetic fields.
■
Keep the cards dry.
■
Do not flex or bend the cards, and do not place heavy
■
Avoid using or storing the drive where it will be
objects on top of them.
subjected to shock or vibration.
■
Do not force cards into the slot.
■
Do not disassemble or dismantle the optical drive.
■
Avoid dropping cards, or subjecting them to excessive
■
Use of a commercially available lens cleaner is
vibration.
recommended for regular maintenance of your drive.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 74 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
74
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 75 Thursday, February 19, 2004 4:52 PM
7
Specifications
75
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 76 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
76
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 77 Thursday, February 19, 2004 4:52 PM
S p e c i f i c a t i o n s
CONFIGURATION LABEL
Specifications
There is a configuration label located on the bottom of
your LifeBook notebook. (See figure 2-7 on page 10 for
location) This label contains specific information
regarding the options you’ve chosen for your notebook.
Following is an example label and information on how to
read your own configuration label.
This section provides the hardware and environmental
specifications for your Fujitsu LifeBook notebook. Spec-
ifications of particular configurations will vary.
Part Number
Configuration ID
ASUXXXXXXXXXXXXX
P/N:
FPC P/N: FPCM41061
S7010, PM 1.7G, 14XGA, XPP, 30G, 256M, LAN/WLAN
Model #
Processor Screen Size Operating Hard Drive Memory
System
Communications
Figure 7-1 Configuration Label
MICROPROCESSOR
Intel Pentium M processor (Refer to the system label to
AUDIO
Sigmatel ST9751T codec
■
■
■
■
determine the speed of your processor).
Stereo headphone jack, 3.5 mm, 1 V or less,
minimum impedance 32 Ohms
rms
CHIPSET
Intel 855GME
Mono microphone jack, 3.5 mm, 100 mV or less,
p-p
minimum impedance 10K Ohms
Two built-in stereo speakers, 20 mm diameter
MEMORY
System Memory
MASS STORAGE DEVICE OPTIONS
Hard Drive
80 GB, 60 GB, 40 GB, or 30 GB fixed hard drive, Ultra
DMA 100 (4200 rpm), 2.5”, 9.5 mm
DDR 333 MHz SDRAM memory module.
256 MB pre-installed in one DIMM slot;
one open DIMM slot available for upgrade.
Upgradeable to 2 GB of total memory (1 GB x 2)
Media Player
Cache Memory
1MB L2 on-die
Depending upon the configuration of your system, one
of the following is installed.
■
CD Drive (modular 24x maximum), or,
Combo DVD/CD-RW Drive (modular 8x maximum
VIDEO
■
Built-in color flat-panel TFT active matrix LCD display
with simultaneous display capability
DVD/24x maximum write, 10x maximum rewrite,
24x maximum read CD-RW combo drive), or,
Super-Multi DVD Drive (modular 4x DVD-R, 2x
■
Video Color and Resolution
DVD-RW, 2.4x DVD+R, 2.4x DVD+RW, 2x DVD-
RAM, 8x DVD-ROM, 16x CD-R, 8x CD-RW, 24x
CD-ROM)
14.1" TFT XGA
■
Internal: 1024 x 768 pixel resolution, 16M colors
External: 1600 x 1200 pixel resolution, 16M colors
■
■
Simultaneous Video: 1024 x 768, 16M colors. XGA,
SVGA and VGA compatible
Video RAM
Intel® 855GME video graphics chip with integrated 32-
bit 3D/2D gfx core with Accelerated Graphics Port
(AGP) support. Up to 64 MB shared video memory
using Dynamic Video Memory Technology (DVMT).
77
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 78 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
■
■
■
■
One LAN (RJ-45) connector
FEATURES
One stereo headphone jack. (See Audio specifications)
One mono microphone jack. (See Audio specifications)
Embedded Smart Card Reader (requires third-party
application)
Integrated Pointing Device
■
Touchpad pointing device with scroll button
Optional Quick Point cursor control button
■
■
■
Wireless LAN antenna with pre-installed on/off switch
Optional Bluetooth module with antenna
Communications
Modem: Internal V.90 standard 56K fax/modem
(ITU V.90, 56K data, 14.4K fax)
On the Optional Port Replicator:
One 6-pin mini DIN PS/2 compatible connectors for
■
Gigabit LAN: Internal wired 10Base-T/100Base-Tx/
1000Base-T/Tx Ethernet LAN
external keyboard or mouse
One 25-pin D-SUB connector for parallel input/
■
Wireless LAN:
output devices; Bi-directional, output only or ECP
One 15-pin D-SUB connector for VGA external
monitor (see Display specifications)
One 9-pin D-SUB connector for RS-232C serial
input/output devices
Four USB 2.0 (Universal Serial Bus) connectors for
input/output devices
One LAN (RJ-45) connector
One DC In connector
One microphone In jack
One headphone jack
One Digital Video (DVI-D) 24-pin, female interface
One power/suspend/resume button
■
Certain configurations of the Lifebook S7000 notebook
have an optional Wireless LAN device installed. If you have
an IntelPRO device installed, your system is classified as a
Centrino product. If you have a Wireless LAN device other
than IntelPRO installed, your system is classified as a
Pentium M product. (For additional information about
the Wireless LAN device, refer to the Wireless LAN User’s
Guide on page 115).
■
■
■
■
■
■
S7010 Model: Integrated Intel PRO Wireless LAN
■
■
■
(802.11b/g), Wi-Fi-compliant
S7010D Model: Optional integrated Atheros Wireless
■
LAN (802.11a+b/g), Wi-Fi-compliant
Optional Bluetooth device for wireless personal area
■
KEYBOARD
network communication
Built-in keyboard with all functions of 101 key PS/2
compatible keyboards.
LifeBook Security/Application Panel
The Application Launcher buttons on your LifeBook
notebook default to the following applications:
■
Total number of keys: 84
Function keys: F1 through F12
Feature extension key: Fn
Two Windows keys: one Start key, one application key
Key pitch: 19 mm
Key stroke: 3 mm
Built-in Touchpad pointing device with left and right
■
■
Table 7-1 Application Launcher Defaults
■
■
Button
Label
Button
Function
Default Application
■
■
1
2
3
4
Application A
Application B
Internet
Notepad
buttons and scroll button.
Built-in Palm Rest
Optional Quick Point cursor control button
■
Calculator
■
Internet Explorer
Netscape Messenger
External Keyboard Support
USB or PS/2-compatible (PS/2 compatible with Port
Replicator only)
E-Mail
Theft Prevention Lock
Lock slot for use with security restraint systems. The
Kensington locking system is recommended.
External Mouse Support
USB or PS/2-compatible (PS/2 compatible with Port
Replicator only)
DEVICE PORTS
POWER
Batteries
On the LifeBook notebook:
PC Card slots for two Type I or Type II cards or one
■
One 6-cell Lithium ion battery, rechargeable, 10.8V,
4800 mAh, 51.8 Wh
Type III card: PCMCIA Standard 2.1 with CardBus
support
■
One 15-pin D-SUB connector for VGA external
Optional Flexible Bay battery: 6-cell Lithium ion battery,
rechargeable, 10.8V, 3400 mAh, 36.7 Wh
monitor (see Display specifications)
Three USB 2.0 (Universal Serial Bus) connectors for
■
input/output devices
One IEEE 1394 (4-pin type) jack
One stereo line-in jack
One modular modem (RJ-11) connector
AC Adapter
■
Autosensing 100-240V AC, supplying 19V DC, 3.16A,
60W to the LifeBook notebook, Fujitsu Model
FPCAC26AP, which includes an AC cable.
■
■
78
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 79 Thursday, February 19, 2004 4:52 PM
S p e c i f i c a t i o n s
Power Management
Conforms to ACPI (Advanced Configuration and Power
Interface).
Carrying Cases
■
Diplomat
Backpack
Director
■
■
DIMENSIONS AND WEIGHT
Overall Dimensions
■
MobileMax Wheeled Case
PRE-INSTALLED SOFTWARE
Approximately 12.05"(w) x 9.72"(d) x 1.0”/1.3”(h)
(306 mm x 247 mm x 25.4/33.0 mm)
Depending on your pre-installed operating system, your
Fujitsu LifeBook notebook comes with pre-installed
software for playing audio and video files of various
formats. In addition there is file transfer software, virus
protection software and Power Management software.
The following list indicates the pre-installed software
associated with your system.
Weights
Approximately 3.85 lbs (1.75 kg) with battery and
weight saver.
Approximately 4.3 lbs (1.95 kg) with battery and DVD/
CD-RW Combo drive.
■
Adobe Acrobat Reader
Drive Image Special Edition (DISE)
EarthLink 5.0
BatteryAid
ENVIRONMENTAL REQUIREMENTS
Temperature
Operating: 41° to 95° F (5° to 35° C)
Non-operating: 5° to 140° F (–15° to 60° C)
■
■
■
■
Fujitsu HotKey/Fujitsu BatteryAid
Humidity
■
■
■
■
■
■
■
■
■
LifeBook Security/Application Panel
Symantec Norton AntiVirus 2004 (90-day free trial)
Netscape 7.0
Quicken 2004 New User Edition
Microsoft Works 7.0
MS Reader*
Journal Viewer*
Zinio™ Reader*
NewsStand™ Reader*
Operating: 20% to 85%, relative, non-condensing
Non-operating; 8% to 85%, relative, non-condensing
Altitude
Operating: 10,000 feet (3,048 m) maximum
POPULAR ACCESSORIES
For ordering or additional information on
Fujitsu accessories please visit our Web site at
us.fujitsu.com/computers or call 1-800-733-0884.
* Indicates that the software is available for user installa-
tion in the “third-party software”.
Memory Upgrades
■
256 MB SDRAM
512 MB SDRAM
1GB SDRAM
LEARNING ABOUT YOUR SOFTWARE
Tutorials
All operating systems and most application software
have tutorials built into them upon installation. We
highly recommend that you step through the tutorial
before you use an application.
■
■
Docking
■
Port Replicator
Power
Manuals
■
Main Lithium ion battery
Battery Charger
Auto/Airline Adapter
AC Adapter
Included with your notebook you will find manuals for
your installed operating system and other pre-installed
software. Any manuals that are not included, are avail-
able online through the help system of the software. We
recommend that you review these manuals for general
information on the use of these applications.
■
■
■
PC Cards
■
Wireless PC Card
4-in-1 Media Card Adapter
Compact Flash Media Card Adapter
■
■
Adobe Acrobat Reader
The Adobe Acrobat Reader, located in the Service and
Support Software folder, allows you to view, navigate,
and print PDF files from across all of the major
computing platforms.
Additional Accessories
■
Wireless Keyboard and Mouse
External USB Floppy Disk Drive
Presentation Audio System
TeleAdapt 16' TeleCord
■
■
■
BatteryAid (Windows 2000 only)
■
Notebook Guardian Lock
BatteryAid allows you to control the display brightness
of your notebook in order to maximize battery life. (See
your BatteryAid online help for more information on the
correct way to use this program)
■
IBM Modem Saver
79
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 80 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Drive Image Special Edition (DISE) by PowerQuest
DISE by PowerQuest provides a way to restore your
computer if you experience a hard disk crash or other
system failure. DISE is used to restore the factory image
and restore the system to its original state.
The Security Panel portion allows for password protection
while the system is off or in Suspend mode. The Security
Panel utilities are found under the Start menu, under
Programs, then under LifeBook Security Panel.
The Application Panel utilities are found under the Start
menu, Settings/Control Panel, then Application Panel. To
open the CD Player and Application Panel Help, select
Start, Programs, LifeBook Application Panel.
Earthlink 5.0
Software suite that allows you to connect with the
Internet.
Fujitsu HotKey (Windows XP only)
Norton AntiVirus 2004
Fujitsu HotKey allows you to control the display bright-
ness of your notebook in order to maximize battery life.
Your system is preinstalled with a free 90-day trial
version of Symantec’s Norton AntiVirus™ 2003. Norton
AntiVirus is a program designed to protect your Life-
Book notebook from computer viruses. It assists in the
protection of the data currently residing on your hard
disk from destruction or contamination. The 90-day
trial version is activated upon your acceptance of soft-
ware license agreement. After 90 days, it will be neces-
sary to purchase a subscription from Symantec to
download latest virus definitions.
Quicken 2004 New User Edition
Quicken 2004 New User Edition by Intuit is a personal
money
management program. It has features such as portfolio
management, account registries, on-line banking
and bill paying features. This application is for new users
who are using Quicken software for the first time. Full
version upgrade information is available on line.
Netscape 7.0
LifeBook Security/Application Panel Software
Your LifeBook notebook is pre-installed with software
utilities that let you operate and configure your LifeBook
Security/Application Panel.
Browser suite, including integrated E-mail accounts,
instant messaging, address book, search, and other tools
and plug-ins.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 81 Thursday, February 19, 2004 4:52 PM
8
Glossary
81
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 82 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
82
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 83 Thursday, February 19, 2004 4:52 PM
G l o s s a r y
Boot
Glossary
To start-up a computer and load its operating system
from disk, ROM or other storage media into RAM.
AC Adapter
A device which converts the AC voltage from a
wall outlet to the DC voltage needed to power
your LifeBook notebook.
Bus
An electrical circuit which passes data between the CPU
and the sub-assemblies inside your LifeBook notebook.
ACPI
Byte
Advanced Configuration and Power Interface
8 bits of parallel binary information.
Active-Matrix Display
Cache Memory
A type of technology for making flat-panel displays
which has a transistor or similar device for every pixel
on the screen.
A block of memory built into the micro-processor which
is much faster to access than your system RAM and used
in specially structured ways to make your overall data
handling time faster.
AdHoc
A name of a wireless LAN configuration.
CardBus
A faster, 32-bit version of the PC Card interface which
offers performance similar to the 32-bit PCI
architecture.
It is a type of communication using wireless cards only.
Another type of communication is called Infrastructure
(using a wireless card and an access point).
CD-ROM
ADSL
Compact disk read only memory. This is a form of
digital data storage which is read optically with a laser
rather than a magnetic head. A typical CD-ROM can
contain about 600MB of data and is not subject to heads
crashing into the surface and destroying the data when
there is a failure nor to wear from reading.
Asymmetric Digital Subscriber Line
Technology for transporting high bit-rate services over
ordinary phone lines.
AGP
Accelerated Graphics Port
Channel
Graphics port specifically designed for graphics-inten-
sive devices, such as video cards and 3D accelerators.
A radio frequency band used for communication
between wireless cards and access points.
Auto/Airline Adapter
CMOS RAM
A device which converts the DC voltage from an auto-
mobile cigarette lighter or aircraft DC power outlet to
the DC voltage needed to power your LifeBook note-
book.
Complementary metal oxide semiconductor random
access memory. This is a technology for manufacturing
random access memory which requires very low levels of
power to operate.
BIOS
COM Port
Basic Input-Output System. A program and set of
default parameters stored in ROM which tests and
operates your LifeBook notebook when you turn it on
until it loads your installed operating system from disk.
Information from the BIOS is transferred to the installed
operating system to provide it with information on the
configuration and status of the hardware.
Abbreviation for communication port. This is your
serial interface connection.
Command
An instruction which you give your operating system.
Example: run a particular application or format a floppy
disk.
Bit
Configuration
The combination of hardware and software that makes
An abbreviation for binary digit. A single piece of
information which is either a one (1) or a zero (0).
up your system and how it is allocated for use.
bps
CRT
An abbreviation for bits per second. Used to describe
Cathode Ray Tube. A display device which uses a beam
data transfer rates.
of electronic particles striking a luminescent screen. It
83
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 84 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
produces a visual image by varying the position and
intensity of the beam.
DNS
Domain Name System
A function to control the association between the IP
address and the name assigned to the computer.
Data
The information a system stores and processes.
If you do not know the IP address but if you know the
computer name, you can still communicate to that
computer.
DC
Direct current. A voltage or current that does not
fluctuate periodically with time.
DOS
Default Value
Disk Operating System (MS-DOS is a Microsoft Disk
Operating System).
A pre programmed value to be used if you fail to set your
own.
Driver
DHCP
A computer program which converts application and
operating system commands to external devices into the
exact form required by a specific brand and model of
device in order to produce the desired results from that
particular equipment.
Dynamic Host Configuration Protocol
A protocol used to automatically acquire parameters
required for the communication, such as IP address.
The sender of IP address is called a DHCP server, and
the receiver is called a DHCP client.
DVMT
Dynamic Video Memory Technology
DIMM
Dual-in-line memory module.
A video memory architecture that increases the
efficiency of the motherboard by using innovative
memory utilization and direct AGP.
DISE
Drive Image Special Edition.
A utility that allows you to restore the original factory
image on your hard drive in the event of corruption or
accidental erasure of files or applications.
ECP
Extended Capability Port. A set of standards for high
speed data communication and interconnection
between electronic devices.
Disk
Encryption Key (Network Key)
A spinning platter of magnetic data storage media. If the
platter is very stiff it is a hard drive, if it is highly flexible
it is a floppy disk, if it is a floppy disk in a hard housing
with a shutter it is commonly called a diskette.
Data encryption key used to encrypt message text and
for computing message integrity checks. Data encryp-
tion protects data from unauthorized viewing.
This device uses the same encryption key to encode and
decode the data, and the identical encryption key is
required between the sender and receiver.
Disk Drive
The hardware which spins the disk and has the heads
and control circuitry for reading and writing the data
on the disk.
ESD
Electro-Static Discharge. The sudden discharge of elec-
tricity from a static charge which has built-up slowly.
Example: the shock you get from a doorknob on a dry
day or the sparks you get from brushing hair on a dry
day.
Diskette
A floppy disk in a hard housing with a shutter.
DMA
Direct Memory Access. Special circuitry for memory
to memory transfers of data which do not require
CPU action.
Extended Memory
All memory more than the 640KB recognized by
MS-DOS as system memory.
DMI
Desktop Management Interface. A standard that
provides PC management applications with a common
method of locally or remotely querying and configuring
PC computer systems, hardware and software compo-
nents, and peripherals.
FCC
Federal Communication Commission.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 85 Thursday, February 19, 2004 4:52 PM
G l o s s a r y
Floppy Disk
Class B - supports 65,000 hosts on each of 16,000
networks
A spinning platter of magnetic data storage media which
is highly flexible.
Class C - supports 254 hosts on each of 2 million
networks
GB
Gigabyte.
The number of unassigned Internet addresses is running
out, so a new classless scheme called CIDR is gradually
replacing the system based on classes A, B, and C and is
tied to adoption of IPv6. (credit: webopedia.com)
Hard drive
A spinning platter of magnetic data storage media where
the platter is very stiff.
IR
I/O
An abbreviation for infrared.
Input/Output. Data entering and leaving your notebook
in electronic form.
IrDA
Infrared Data Association. An organization which
produces standards for communication using infrared
as the carrier.
I/O Port
The connector and associated control circuits for data
entering and leaving your notebook in electronic form.
IRQ
IDE
Interrupt Request. An acronym for the hardware signal
to the CPU that an external event has occurred which
needs to be processed.
Intelligent Drive Electronics. A type of control interface
for a hard drive which is inside the hard drive unit.
Infrared
KB
Kilobyte.
Light just beyond the red portion of the visible light
spectrum which is invisible to humans.
LAN
Infrastructure
Local Area Network. An interconnection of computers
and peripherals within a single limited geographic
location which can pass programs and data amongst
themselves.
A name of a wireless LAN configuration. This type of
communication uses an access point.
Another type of communication is called AdHoc.
IP Address
LCD
Liquid Crystal Display. A type of display which makes
images by controlling the orientation of crystals in a
crystalline liquid.
An identifier for a computer or device on a TCP/IP
network. Networks using the TCP/IP protocol route
messages based on the IP address of the destination. The
format of an IP address is a 32-bit numeric address
written as four numbers separated by periods. Each
number can be zero to 255. For example, 1.160.10.240
could be an IP address.
Lithium ion Battery
A type of rechargeable battery which has a high power-
time life for its size and is not subject to the memory
effect as Nickel Cadmium batteries.
Within an isolated network, you can assign IP addresses
at random as long as each one is unique. However,
connecting a private network to the Internet requires
using registered IP addresses (called Internet addresses)
to avoid duplicates.
LPT Port
Line Printer Port. A way of referring to parallel interface
ports because historically line printers were the first and
latter the most common device connected to parallel
ports.
The four numbers in an IP address are used in different
ways to identify a particular network and a host on that
network. Three regional Internet registries -- ARIN,
RIPE NCC and APNIC -- assign Internet addresses from
the following three classes.
MAC Address
Media Access Control Address
A unique physical address of a network card. For
Ethernet, the first three bytes are used as the vendor
code, controlled and assigned by IEEE. The remaining
three bytes are controlled by each vendor (preventing
Class A - supports 16 million hosts on each of 126
networks
85
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 86 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
overlap), therefore, every Ethernet card is given a unique
physical address in the world, being assigned with a
different address from other cards. For Ethernet, frames
are sent and received based on this address.
Operating System
A group of control programs that convert application
commands, including driver programs, into the exact
form required by a specific brand and model of micro-
processor in order to produce the desired results from
that particular equipment.
MB
Megabyte.
Partition
Megahertz
A block of space on a hard drive which is set aside and
made to appear to the operating system as if it were a
separate disk, and addressed by the operating system
accordingly.
1,000,000 cycles per second.
Memory
A repository for data and applications which is readily
accessible to your LifeBook notebook’s CPU.
PCI
Peripheral Component Interconnect
MHz
Megahertz.
Self-configuring PC local bus. Designed by Intel, PCI has
gained wide acceptance as a standard bus design.
MIDI
PCMCIA
Musical Instrument Digital Interface. A standard
communication protocol for exchange of information
between computers and sound producers such
as synthesizers.
PCMCIA is a trademark of the Personal Computer
Memory Card International Association. The Personal
Computer Memory Card International Association is an
organization that sets standards for add-in cards for
personal computers.
Modem
A contraction for MOdulator-DEModulator. The
equipment which connects a computer or other data
terminal to a communication line.
Peripheral Device
A piece of equipment which performs a specific
function associated with but not integral to a computer.
Examples: a printer, a modem, a CD-ROM.
Monaural
A system using one channel to process sound from all
sources.
Pitch (keyboard)
The distance between the centers of the letter keys of a
keyboard.
MPU-401
A standard for MIDI interfaces and connectors.
Pixel
MTU
The smallest element of a display, a dot of color on your
display screen. The more pixels per area the clearer your
image will appear.
Maximum Transmission Unit
The maximum data size that can be transferred at a time
through the Internet or other networks. You can set a
smaller MTU size to obtain successful communication,
if you have difficulty transferring data due to the fact
that the maximum size is too large.
POST
Power On Self Test. A program which is part of the BIOS
which checks the configuration and operating condition
of your hardware whenever power is applied to your
notebook. Status and error messages may be displayed
before the operating system is loaded. If the self test
detects failures that are so serious that operation can not
continue, the operating system will not be loaded.
Norton AntiVirus
Web-based software that protects you email, instant
messages, and other files by removing viruses, worms,
and Trojan horses.
PPPoE
NTSC
Point to Point Protocol over Ethernet.
National TV Standards Commission. The standard for
A protocol for Ethernet, using a Point-to-Point Protocol
(PPP), which is used for connection on the phone line.
TV broadcast and reception for the USA.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 87 Thursday, February 19, 2004 4:52 PM
G l o s s a r y
Program
term failure predictions for hard drives. When SMART is
enabled the hard drive monitors pre-determined drive
attributes that are susceptible to degradation over time.
If a failure is likely to occur, SMART makes a status
report available so that the LifeBook notebook can
prompt the user to back up the data on the drive. Natu-
rally not all failures are predictable. SMART predict-
ability is limited to those attributes which the drive can
self-monitor. In those cases where SMART can give
advance warning, a considerable amount of precious
data can be saved.
An integrated set of coded commands to your
computers telling your hardware what to do and how
and when to do it.
Protocol
Procedures and rules use to send and receive data
between computers.
- Method of sending and receiving data
- Process used to handle communication errors
Conditions required for communication are organized
in procedures for correct transfer of information.
SRAM
Static random access memory. A specific technology of
making RAM which does not require periodic data
refreshing.
RAM
Random Access Memory. A hardware component of
your LifeBook notebook that holds binary information
(both program and data) as long as it has the proper
power applied to it.
SSID
Service Set Identifier
Specifies which network you are joining. Some systems
allow you to specify any SSID as an option so you can
join any network.
RAM Module
A printed circuit card with memory and associated
circuitry which allows the user to add additional
memory to the computer without special tools.
Standby
To make inoperative for a period of time. Your LifeBook
notebook uses various suspension states to reduce power
consumption and prolong the charge of your battery.
Reset
The act of reloading the operating system. A reset erases
all information stored in RAM.
Status Indicator
Restart
See Reset.
A display which reports the condition of some portion
of your hardware. On your LifeBook notebook this is an
LCD screen just above the keyboard.
Resume
To proceed after interruption. In your notebook this
refers to returning to active operation after having been
in one of the suspension states.
Stereo (audio)
A system using two channels to process sound from two
different sources.
ROM
SVGA
Read Only Memory. A form of memory in which infor-
mation is stored by physically altering the material. Data
stored in this way can not be changed by your notebook
and does not require power to maintain it.
Super VGA.
S-Video
Super Video. A component video system for driving a
TV or computer monitor.
SDRAM
System Clock
Synchronous Dynamic Random Access Memory.
An oscillator of fixed precise frequency which synchro-
nizes the operation of the system and is counted to
provide time of day and date.
Serial Port
A connection to another device through which data is
transferred one bit at a time on a single wire with any
other wires only for control of the device not for transfer
of data.
TCP/IP
Transmission Control Protocol/Internet Protocol.
A standard Internet protocol that is most widely used.
SMART
Self-Monitoring, Analysis and Reporting Technology
(SMART) is an emerging technology that provides near-
87
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 88 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
TFT
Thin Film Transistor – A technology for flat display
panels which uses a thin film matrix of transistors to
control each pixel of the display screen individually.
UL
Underwriters Laboratories – An independent organiza-
tion that tests and certifies the electrical safety of devices.
USB
Universal Serial Bus.
Standard that allows you to simultaneously connect up
to 127 USB devices such as game pads, pointing devices,
printers, and keyboards to your computer.
VGA
Video Graphics Array. A video display standard
originally introduced by IBM with the PS/2 series of
personal computers.
VRAM
Video Random Access Memory. A memory dedicated to
video display data and control.
WFM
Wired for Management is Intel’s broad-based initiative
to reduce the total cost of ownership (TCO) of business
computing without sacrificing power and flexibility.
Wi-Fi Compatible
Wi-Fi (Wireless Fidelity) Identifies that the product has
passed the interoperability test, supplied by the WECA
(Wireless Ethernet Compatibility Alliance), which guar-
antees the interoperability of wireless IEEE 802.11 LAN
products. For more information on the Wi-Fi standard,
go to the WECA Web site at: www.wirelessethernet.com.
WLAN
Wireless Local Area Network. A wireless interconnection
of computers and peripherals within a single limited
geographic location which can pass programs and data
amongst themselves.
Write Protect
Prevent alteration of the binary state of all bits in a
storage media. Example: all information on a device
such as a floppy diskette; a block of space in a storage
media such as a partition of a hard drive; a file or direc-
tory of floppy diskette or hard drive.
XGA
Extended VGA.
Zip Drive
A 100MB or 250MB read/write removable media disk
drive.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 89 Thursday, February 19, 2004 4:52 PM
R e g u l a t o r y I n f o r m a t i o n
The ringer equivalent number (REN) of this equipment
is 0.0B as shown on the label. The REN is used to deter-
mine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone may
result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as
determined by the total RENs, contact the local tele-
phone company.
Regulatory Information
NOTICE
Changes or modifications not expressly approved by
Fujitsu could void this user’s authority to operate the
equipment.
FCC NOTICES
Notice to Users of Radios and Television
These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
If this equipment causes harm to the telephone network,
the telephone company will notify you in advance that
temporary discontinuance of service may be required.
But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
The telephone company may make changes in its facili-
ties, equipment, operations or procedures that could
effect the operation of the equipment. If this happens
the telephone company will provide advance notice in
order for you to make necessary modifications to main-
tain uninterrupted service.
n
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
n
receiver.
n
n
If trouble is experienced with this equipment, for repair
or warranty information, please refer to the manual or
contact Fujitsu Computer Systems Corporation,
Customer Service. If the equipment is causing harm to
the telephone network, the telephone company may
request that you disconnect the equipment until the
problem is resolved.
Connect the equipment into an outlet that is on a
different circuit than the receiver.
Consult the dealer or an experienced radio/TV
technician for help.
Shielded interconnect cables must be employed with this
equipment to ensure compliance with the pertinent RF
emission limits governing this device.
The equipment cannot be used on public coin service
provided by the telephone company. Connection to
party line service is subject to state tariffs. (Contact the
state public utility commission, public service commis-
sion or corporation commission for information).
Notice to Users of the US Telephone Network
This equipment complies with Part 68 of the FCC rules,
and the requirements adopted by ACTA. On the bottom
of this equipment is a label that contains, among other
information, the FCC registration number and ringer
equivalence number (REN) for this equipment; or a
product identifier in the format US:AAAEQ##TXXXX.
If requested, this information or number must be
provided to the telephone company.
If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation
of this computer does not disable your alarm equip-
ment. If you have any questions about what will disable
alarm equipment, consult your telephone company or a
qualified installer.
This equipment is designed to be connected to the tele-
phone network or premises wiring using a standard jack
type USOC RJ11C. A plug and jack used to connect this
equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided
with this product. It is designed to be connected to a
compatible modular jack that is also compliant.
The Telephone Consumer Protection Act of 1991 makes
it unlawful for any person to use a computer or other
electronic device to send any message via a telephone fax
machine unless such message clearly contains in a
margin at the top or bottom of each transmitted page or
on the first page of the transmission, the date an time it
is sent and an identification of the business or other
entity, or other individual sending the message and the
telephone number of the sending machine or such busi-
ness, other entity, or individual.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 90 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
DOC (INDUSTRY CANADA) NOTICES
Avis Aux Utilisateurs Du Réseau
Notice to Users of Radios and Television
Téléphonique Canadien
This Class B digital apparatus meets all requirements of
Canadian Interference-Causing Equipment Regulations.
AVIS: Le présent matériel est conforme aux spécifica-
tions techniques d’Industrie Canada applicables au
matériel terminal. Cette conformité est confirmée par le
numéro d’enregistrement. Le sigle IC, placé devant le
numéro d’enregistrement, signifie que l’enregistrement
s’est effectué conformément à une déclaration de
conformité et indique que les spécifications techniques
d’Industrie Canada ont été respectées. Il n’implique pas
qu’Industrie Canada a approuvé le matériel.
CET appareil numérique de la class B respecte toutes les
exigence du Réglement sur le matérial brouilleur du
Canada.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry
Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The
abbreviation, IC, before the registration number signi-
fies that registration was performed based on a Declara-
tion of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that
Industry Canada approved the equipment.
Avant de connecter cet équipement à une ligne télépho-
nique, l’utilisateur doit vérifier s’il est permis de
connecter cet équipement aux installations de télécom-
munications locales. L’utilisateur est averti que même la
conformité aux normes de certification ne peut dans
certains cas empêcher la dégradation du service.
Before connecting this equipment to a telephone line the
user should ensure that it is permissible to connect this
equipment to the local telecommunication facilities.
The user should be aware that compliance with the
certification standards does not prevent service
degradation in some situations.
Les réparations de l’équipement de télécommunications
doivent être eVectuées par un service de maintenance
agréé au Canada. Toute réparation ou modification, qui
n’est pas expressément approuvée par Fujitsu, ou toute
défaillance de l’équipement peut entraîner la compagnie
de télécommunications à exiger que l’utilisateur décon-
necte l’équipement de la ligne téléphonique.
Repairs to telecommunication equipment should be
made by a Canadian authorized maintenance facility.
Any repairs or alterations not expressly approved by
Fujitsu or any equipment failures may give the telecom-
munication company cause to request the user to
disconnect the equipment from the telephone line.
AVIS: L’indice d’équivalence de la sonnerie (IES) du
présent matériel est de 0.0. L’IES assigné à chaque
dispositif terminal indique le nombre maximal de
terminaux qui peuvent être raccordés à une interface
téléphonique. La terminaison d’une interface peut
consister en une combinaison quelconque de dispositifs,
à la seule condition que la somme d’indices d’équiva-
NOTICE: The Ringer Equivalence Number (REN) for
this terminal equipment is 0.0. The REN assigned to
each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected
to a telephone interface. The termination on an interface
may consist of any combination of devices subject only
to the requirement that the sum of the Ringer Equiva-
lence de la sonnerie de tous les dispositifs n’excède pas 5.
Pour assurer la sécurité, les utilisateurs
doivent vérifier que la prise de terre du ser-
vice d’électricité, les lignes télphoniques et
les conduites d’eau métalliques sont con-
nectées ensemble. Les utilisateurs NE
doivent PAS tenter d’établir ces connex-
ions eux-mêmes, mais doivent contacter
les services d’inspection d’installations
électriques appropriés ou un électricien.
Ceci peut être particulièrement important
en régions rurales.
lence Numbers of all the devices does not exceed five.
For safety, users should ensure that the
electrical ground of the power utility, the
telephone lines and the metallic water
pipes are connected together. Users should
NOT attempt to make such connections
themselves but should contact the appro-
priate electric inspection authority or elec-
trician. This may be particularly important
in rural areas.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 91 Thursday, February 19, 2004 4:52 PM
R e g u l a t o r y I n f o r m a t i o n
UL Notice
This unit requires an AC adapter to operate. Use only UL
Listed Class 2 Adapters with an output rating of 19
VDC, with a current of 3.16 A.
AC Adapter output polarity:
+
The modem-to-telephone network con-
nection must be a line cord using a mini-
mum #26 AWG wire.
For Authorized Repair Technicians Only
n
For continued protection against risk of
fire, replace only with the same type and
rating fuse.
n
Danger of explosion if Lithium (clock)
battery is incorrectly replaced. Replace
only with the same or equivalent type
recommended by the manufacturer. Dis-
pose of used batteries according to the
manufacturer’s instruction.
System Disposal
LAMP(S) INSIDE THIS PRODUCT
CONTAIN MERCURY AND MUST
BE RECYCLED OR DISPOSED OF
Hg
ACCORDING TO LOCAL, STATE, OR
FEDERAL LAWS.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 92 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
92
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 115 Thursday, February 19, 2004 4:52 PM
Appendix
Integrated Wireless
LAN* User’s Guide
* Optional device
115
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 116 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
116
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 93 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with
the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation.
FCC REGULATORY INFORMATION
Please note the following regulatory information related to the
optional wireless LAN module.
Regulatory Notes and Statements
Wireless LAN, Health and Authorization for use
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try and correct
the interference by one or more of the following measures:
Radio frequency electromagnetic energy is emitted from Wire-
less LAN devices. The energy levels of these emissions, however,
are far much less than the electromagnetic energy emissions
from wireless devices such as mobile phones. Wireless LAN
devices are safe for use by consumers because they operate
within the guidelines found in radio frequency safety standards
and recommendations. The use of Wireless LAN devices may be
restricted in some situations or environments, such as:
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the equipment and the
receiver.
3. Connect the equipment to an outlet on a circuit different
from the one the receiver is connected to.
■
■
■
On board an airplane, or
In an explosive environment, or
4. Consult the dealer or an experienced radio/TV technician
for help.
In situations where the interference risk to other devices or
services is perceived or identified as harmful.
FCC Radiation Exposure Statement
In cases in which the policy regarding use of Wireless LAN
devices in specific environments is not clear (e.g., airports,
hospitals, chemical/oil/gas industrial plants, private buildings),
obtain authorization to use these devices prior to operating the
equipment.
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of
20 centimeters between the Wireless LAN/Bluetooth antenna
(located on the top edge of the LCD screen) and your body.
Regulatory Information/Disclaimers
The transmitters in this device must not be co-located or oper-
ated in conjunction with any other antenna or transmitter.
Installation and use of this Wireless LAN device must be in
strict accordance with the instructions included in the user
documentation provided with the product. Any changes or
modifications made to this device that are not expressly
approved by the manufacturer may void the user’s authority to
operate the equipment. The manufacturer is not responsible for
any radio or television interference caused by unauthorized
modification of this device, or the substitution or attachment of
connecting cables and equipment other than those specified by
the manufacturer. It is the responsibility of the user to correct
any interference caused by such unauthorized modification,
substitution or attachment. The manufacturer and its autho-
rized resellers or distributors will assume no liability for any
damage or violation of government regulations arising from
failure to comply with these guidelines.
Export Restrictions
This product or software contains encryption code which may
not be exported or transferred from the US or Canada without
an approved US Department of Commerce export license. This
device complies with Part 15 of FCC Rules., as well as ICES 003
B / NMB 003 B. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesirable operation.
Modifications not expressly authorized by Fujitsu PC Corpora-
tion may invalidate the user's right to operate this equipment.
Canadian Notice
This device must not be co-located or operating in conjunction
with any other antenna or transmitter.
To prevent radio interference to the licensed service, this device
is intended to be operated indoors and away from windows to
provide maximum shielding. Equipment (or its transmit
antenna) that is installed outdoors is subject to licensing.
For Atheros Wireless LAN:
For operation within 5.15~5.25GHz frequency range, it is
restricted to indoor environment, and the antenna of this
device must be integral.
Federal Communications Commission statement
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause interference, and, (2) This device must
accept any interference, including interference that may cause
undesired operation of this device.
FCC Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
93
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 94 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Before Using the Wireless LAN
■
The Integrated Wireless LAN is an optional device avail-
able for Fujitsu mobile computers. This manual
describes the basic operating procedures for the Wireless
LAN (referred to as the “device” in this manual) and
how to set up a wireless LAN network. Before using this
device, read this manual carefully to ensure correct oper-
ation of the device. Keep this manual in a safe place for
reference while using the device.
This wireless module is Wi-Fi compliant. The module
can communicate at a maximum data rate of 54 Mbps.
■
The maximum communication range is approxi-
mately 80 feet (25 meters) inside a building. Please
note that the range you achieve may be shorter or
longer than 80 feet, depending upon factors such as
obstructions, walls, columns, construction material,
and reflective objects.
Types of Wireless LANs Covered by this Document
■
The wireless module s support a number of industry-
standard security mechanisms, including WEP, TKIP,
and 802.1x/EAP (LEAP, TLS, PEAP, MD5).
This document is applicable to systems containing one
of the following two devices. Most of the procedures are
identical. Sections that differ between the two devices
have been noted in the text:
Wireless LAN Modes Using this Device
Ad Hoc Mode (See Figure 1)
■
Intel PROSet Wireless LAN
“Ad Hoc Mode” refers to a type of wireless network that
involves connecting multiple computers without the use
of an Access Point. Network connectivity between
computers can be established using only wireless LAN
cards in a peer-to-peer fashion.
■
Atheros Wireless LAN
If your system is a Stylistic S7010, your wireless module
is the Intel PROSet wireless LAN; if your system is a
Stylistic S7010D, your wireless module is the Atheros
wireless LAN.
Ad Hoc networks are an easy and inexpensive method
for establishing network connectivity between multiple
computers.
Characteristics of the Device
This device consists of a wireless LAN card that is
attached inside the computer via a mini-PCI slot.
In the Ad Hoc mode, you can use the function
supported by Microsoft Network, such as File and Print
Sharing to exchange files and share a printer or other
peripheral devices.
The main characteristics are as follows:
■
It operates in the 2.4 GHz Industrial, Scientific, and
Medical (ISM) RF band; additionally, the Atheros
wireless LAN module operates in both the 2.4 GHz
and 5 GHz RF bands.
To use Ad Hoc Mode, you must set the same SSID and
the same encryption key for all the computers that are
connected. Communication between computers in an
Ad Hoc network will occur provided they are within
each other’s RF coverage area.
■
It does not require an FCC license to operate.
■
It uses Direct Sequence Spread Spectrum (DSSS), an
RF modulation scheme that is resistant to noise.
Figure 1. Ad Hoc Mode Network
94
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 95 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
Figure 2. Access Point (Infrastructure) Mode Network
Wired LAN
ADSL modem,
cable modem,
or similar
Internet
Access Point*
Wireless LAN
* An optional hub for a wired
LAN may be required depending
upon the type of access point used.
Access Point (Infrastructure) Mode (See Figure 2)
number of obstructions, walls, type of construction
material, reflective objects, etc.
Infrastructure mode refers to a wireless network in
which devices communicate with each other by first
going through an Access Point (AP). In infrastructure
mode, wireless devices can communicate with each
other or can communicate with a wired network. Most
corporate wireless LANs operate in infrastructure mode
because they require access to the wired LAN in order to
use services such as file servers or printers.
■
If the computer is unable to communicate properly,
change the channel to be used or the installation loca-
tion. During the use of a microwave oven or other
equipment generating strong high-frequency energy,
in particular, the personal computer may be highly
susceptible to the energy and unable to communicate
properly.
■
Broadcast stations or wireless communication equip-
ment that operate in the 2.4GHz or 5GHz RF Fre-
quency band may interfere with the operation of the
wireless LAN module. Increasing of transmit power or
relocating Access Points may be necessary to combat
the effects of the interference.
How to Handle This Device
The Integrated Wireless LAN device is already installed
in your mobile computer. Under normal circumstances,
it should not be necessary for you to remove or re-install
it. The LAN has been configured to support the oper-
ating system with which your system shipped.
FOR BETTER COMMUNICATIONS
This personal computer may not operate properly due to
the operating environment. Strictly observe the
following precautions when installing the main unit of
the computer:
■
For optimum wireless communications, it recom-
mended that operation of the wireless LAN module
occur within 25 meters of the Access Point. Wireless
range is dependent on a multitude of factors including
95
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 96 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
switching will be deactivated and the transmission
of radio waves from the wireless LAN will be
stopped.
STOPPING TRANSMISSION
To use this product inside hospitals, clinics, or airplanes,
or in other places where the use of electronic equipment
is regulated, stop the transmission of radio waves from
the wireless LAN beforehand.
To restart transmission, check the [Enable
Radio] checkbox to select it., then click the
[OK] button.
Deactivation using the wireless switch
The transmission of radio waves from the wireless LAN
can be stopped by setting the wireless switch to the Off
position. Note that the Wireless LAN On/Off switch has
no effect on non-Wireless LAN models.
STARTING TRANSMISSION
To communicate using the wireless LAN function, set
the computer to a status from which it can transmit, as
follows:
(See Figure 3 for Wireless LAN switch location.)
Intel PROSet Wireless LAN:
1. Set the wireless switch to the On position.
2. Click [Start] --> [(All) Programs] --> [Intel Net-
work Adapters] --> [Intel(R) PROSet]. The
Intel(R) PROSet window will be displayed.
3. Click the [General] tab if it is not already selected.
Wireless LAN
On/Off Switch
4. Select [ON] for the Switch radio: function, then
click [OK]. Wireless communications on/off
switching will be activated and the transmission of
radio waves will be restarted.
Figure 3. Wireless LAN On/Off Switch
Deactivation using Windows
Atheros Wireless LAN:
Intel PROSet Wireless LAN:
1. Click the Wireless Network Connection icon in the
system tray at the lower right of your screen.
1. Click [Start] --> [(All) Programs] --> [Intel Net-
work Adapters] --> [Intel(R) PROSet]. The
Intel(R) PROSet window will be displayed.
2. Click [Enable Radio]. The radio will be turned on.
Access Point Mode: Transmission is enabled.
Ad Hoc Mode: Restart your computer to enable the
radio.
2. Click the General tab.
3. Select [Off] for the wireless communications
Switch Radio: function, and then click the [OK]
button. Wireless communications on/off switching
will be deactivated and the transmission of radio
waves from the wireless LAN will be stopped.
To restart transmission, select [On] for the
wireless communications Switch Radio:
function, and then click the [OK] button.
Atheros Wireless LAN
1. Click [Start] --> [Settings (Windows 2000 only)]
-> [Control Panel] --> [Atheros Wireless Utility].
The Atheros Wireless Configuration Utility win-
dow will be displayed.
2. Click the Wireless Networks tab.
3. Click the [Enable Radio] box to clear it, then click
the [OK] button. Wireless communications on/off
96
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 97 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
Connection using Wireless Zero Configuration Tool
FLOW OF OPERATIONS
The wireless LAN connection procedure contained in
this section is outlined below.
■
To use access point (infrastructure) con-
nection, refer to the access point manual
for the access point-setting procedure.
■
You do not need to set the channel
when using access point (infrastructure)
mode. Channel selection is controlled by
the access point. In ad hoc networks,
channel selection defaults to channel 11;
however, channel selection can be man-
ually changed if desired. This can be
accomplished only when using the client
utility.
1. Make sure the mobile computer is ready for the
transmission of radio waves from the wireless LAN.
For further details, see (See Starting Transmission
on page 96 for more information).
2. Assign the parameters required for wireless LAN
connection. (See Preparation for wireless LAN con-
nection on page 97 for more information).
■
Enter the network name (SSID) and other data.
If it is necessary to change the channel,
change the setting of the access point.
For the setting procedure, refer to the
manual of the access point.
■
Enter the network key (the Wired Equivalent
Privacy or WEP key used to encode 802.11b
communications data).
3. Perform setting operations relating to network con-
nection. (See Connection to the network on page 99
for more information)
1. Make sure the Wireless LAN switch is switched on.
2. Click the [Start] button first and then [Control
Panel].
■
Specify TCP/IP as the protocol, and confirm the name
of the work group and other settings.
3. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed instead.)
■
Enter the data required for file/printer sharing on the
network. Perform this operation as required.
■
For access point (or “infrastructure”) connection,
enter data for the access point. Refer to the manual of
the access point for further details.
4. Double-click the Network Connections icon. A list
of currently installed networks will be displayed.
■
Verify that you are able to connect your computer to
5. Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu dis-
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
the network.
PREPARATION FOR WIRELESS LAN
CONNECTION
This section explains the preparations required for the
6. Click the [Wireless Networks] tab.
use of the wireless LAN.
7. Click [Refresh], then choose the correct SSID from
the [Available Networks] window. Click [Config-
ure] and proceed to step 8. If the SSID of your
access point does not appear in the list, click [Add].
The [Wireless Network Properties] window will be
displayed.
Assigning parameters
Configure the network name (SSID), the network key,
and other data required for wireless LAN connection.
Please contact your network administrator for the
correct configuration parameters.
8. Select the Association tab if it is not already
selected.
9. Enter the information required for connection to
the wireless LAN, as follows.
a. Enter the network name (SSID). (i.e., Enter the
name of the desired network in less than 33
ASCII characters).
For ad hoc connection: Assign the same network
name to all the personal computers to be
connected.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 98 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
For access point (infrastructure) connection:
Assign the appropriate SSID. The SSID must be
identical to the SSID of the access point. Refer to
the access point manual, or contact your network
administrator.
connected.
For access point (infrastructure) connection:
Assign the identical network key that is pro-
grammed into the access point. For this set-
ting, refer to the access point manual or
contact your network administrator.
b. For ad hoc connection, check the following field.
For access point (infrastructure) connection,
clear the check mark for the following field:
e. If using static WEP keys, confirm the Network
key by re-entering the same data in the [Confirm
network key:] field.
[This is a computer-to-computer (ad hoc) net-
work; wireless access points are not used.]
11. Click the [Authentication] tab and then verify the
settings of [Enable IEEE 802.1x authentication for
this network].
10. Configure Wireless Network Key parameters (Net-
work Authentication and Encryption).
For internal use at an organization such as a com-
pany, when access by wireless LAN clients is to be
limited using IEEE 802.1x authentication, check the
[Enable IEEE 802.1x authentication for this net-
work] check box.
It is strongly recommended that you enter
the network key for encoding
communications data. If the network key
is not entered, since the network can be
accessed from all personal computers
containing the wireless LAN function,
there is the danger of your data being
stolen or damaged by other users.
For home use, clear the check mark from [Enable
IEEE 802.1x authentication for this network].
For the setting method relating to IEEE 802.1x
authentication, refer to the manual of the access
point which you are using.
a. Choose the Network Authentication method
appropriate for your wireless LAN. Options
include Open, Shared, WPA, and WPA-PSK.
12. After completion of setting operations, click the
[OK] button. Processing will return to the [Wire-
less Network Connection Properties] window.
b. Choose the Encryption method appropriate for
your wireless LAN. Options for Open or Shared
Authentication are Disabled or WEP. Options for
WPA or WPA-PSK are TKIP or AES.
13. Verify that the network name entered in step 7
above is added in [Preferred Networks], and then
click the [OK] button.
c. If using static WEP keys, clear the check mark
from the [The key is provided for me automati-
cally] check box. If using an authentication
method that uses dynamic WEP (e.g., WPA,
WPA-PSK, 802.1x/EAP), the check box should
remain checked. Please consult your network
administrator for the correct settings.
In [Preferred Networks], register only the
desired connection settings.
14. Close the [Wireless Network] window.
d. Static WEP keys are to be entered in the
[Network Key] box. Configuration of the
[Network Key] is not required if the [The key is
provided for me automatically] check box is
checked.
■
Static WEP keys entered in ASCII code format
will be either five characters (40-bit) or thir-
teen characters (104-bit) in length. Valid char-
acters are 0 - 9, A - Z.
■
Static WEP keys entered in hexadecimal code
format will be either ten characters (40-bit) or
twenty-six characters (104-bit) in length. Valid
characters are 0 - 9, A - F.
For ad hoc connection: Assign the same net-
work key to all the personal computers to be
98
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 99 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
CONNECTION TO THE NETWORK
Confirming the computer and work group names
This section explains connection to the network.
To modify the computer name and/or the
work group name, you need to be logged
in from Windows as an administrator.
If there is an administrator of the network, contact the
network administrator for data settings.
Setting the network
Perform the “Setting TCP/IP” and “Confirming the
computer and work group names” operations required for
network connection.
1. Click the [Start] button, then [Control Panel].
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
Setting TCP/IP
To change the setting of the IP address,
you need to be logged in from Windows
as an administrator.
3. Double-click the [System] icon. The [System Prop-
erties] window will be displayed.
4. Click the [Computer Name] tab.
1. Click the [Start] button first and then [Control
Panel].
5. Confirm the settings of [Full computer name:] and
[Workgroup:].
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
a. The setting of [Full computer name:] denotes the
name for identifying the computer. Any name
can be assigned for each personal computer.
To change the name, click [Change] and
then proceed in accordance with the
instruction messages displayed on the
screen.
3. Double-click [Network Connections]. A list of cur-
rently installed networks will be displayed.
4. Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu dis-
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
Enter the desired name in less than 15 ASCII
character code format. Identifiability can be
enhanced by entering the model number, the
user name, and other factors.
5. Click the [General] tab if it is not already selected.
6. Click [Internet Protocol (TCP/IP] and then click
[Properties]. The [Internet Protocol (TCP/IP)
Properties] window will be displayed.
b. [Workgroup name] is the group name of the
network. Enter the desired name in less than 15
ASCII character code format.
7. Set the IP address as follows:
For ad hoc connection: Assign the same network
name to all personal computers existing on the
network.
■
For ad hoc connection: Select [Use the following
IP address:] and then enter data for [IP address]
and [Subnet mask]. See page 112 for IP address
setting.
For access point (infrastructure) connection:
Assign the name of the work group to be
accessed.
■
For access point (infrastructure) connection: If
your network uses DHCP, select [Obtain an IP
address automatically] and [Obtain DNS server
address automatically]. If your network uses static
IP addresses, consult with your network adminis-
trator for the correct IP address settings.
6. Click the [OK] button. If a message is displayed
that requests you to restart the personal computer,
click [Yes] to restart the computer.
8. Click the [OK] button. Processing will return to the
[Wireless Network Connection Properties] window.
9. Click the [OK] button.
10. Close the [Network Connection] window.
Following this operation, confirm the names of the
computer and the workgroup as follows.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 100 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Setting the sharing function
1. Click the [Start] button first and then [My Com-
puter].
Set the sharing function to make file and/or printer sharing
with other network-connected personal computers valid.
2. Double-click [Local disk (C:)].
This operation is not required unless the sharing func-
tion is to be used.
3. Right-click the “work” folder (or whichever folder
you want to share), and then click [Sharing and
Security...] in the menu displayed. The [Folder
The folder and printer for which the sharing function
has been set will be usable from any personal computer
present on the network.
Name Properties] window will be displayed.Click
Setting the file-sharing function for the file
which has been used to execute Network
Setup Wizard is suggested on the screen.
For the wireless LAN, however, since
security is guaranteed by entry of the
network name (SSID) and the network
key, the steps to be taken to set the file-
sharing function easily without using
Network Setup Wizard are given below.
To share a file and/or the connected
printer, you need to be logged in as an
administrator.
Setting the Microsoft network-sharing service
1. Click the [Start] button first and then [Control
Panel].
2. If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
[Sharing] if it isn’t already selected.
4. Click the link stating “If you understand the secu-
rity risks, but want to share files without running
the wizard, click here”.
5. Click “Just enable file sharing” and click [OK].
3. Double-click [Network Connections]. A list of cur-
rently installed networks will be displayed.
6. Check the [Share this folder on the network] check
box.
4. Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu dis-
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
To specify the corresponding folder as a
read-only folder, select the [Read only]
checkbox under the General tab.
5. If [File and Printer Sharing for Microsoft Net-
works] is displayed, proceed to step 6. If [File and
Printer Sharing for Microsoft Networks] is not dis-
played, skip to step 7.
7. Click the [OK] button. The folder will be set as a
sharable folder, and the display of the icon for the
“work.” folder will change.
6. Make sure that the [File and Printer Sharing for
Microsoft Networks] check box is checked, and
then click the [OK] button. Skip to “Setting file-
sharing function”.
Setting the printer-sharing function
1. Click [Start] and then [Printers and Faxes]. A list of
connected printers will be displayed.
7. Click [Install]. The [Select Network Component
Type] window will be displayed.
2. Right-click the printer for which the sharing func-
tion is to be set, and then click [Sharing] in the
menu displayed. The property window correspond-
8. Click [Service], then click the [Add] button. The
[Select Network Service] window will be displayed.
ing to the selected printer will be displayed.
9. Click [File and Printer Sharing for Microsoft Net-
works] and then click the [OK] button. Processing
will return to the [Wireless Network Connection
Properties] window, and [File and Printer Sharing
for Microsoft Networks] will be added to the list.
Setting the printer-sharing function when
Network Setup Wizard has been executed
is suggested on the screen. For the wireless
LAN, however, since security is guaranteed
by entry of the network name (SSID) and
the network key, the steps to be taken to
set the printer-sharing function without
using Network Setup Wizard are laid down
below.
10. Click the [Close] button.
Setting the file-sharing function
The procedure for setting the file-sharing function
follows, with the “work” folder in drive C: as an
example.
3. Click the [Sharing] tab.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 101 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
■
■
4. Click [Share this printer].
Current Channel
The channel number currently used by the radio.
5. Enter the sharing printer name in [Share name].
6. Click the [OK] button.
Link Status
Displays the current connected state of the
WLAN module.
Confirming connection
After you have finished the network setup operations,
access the folder whose sharing has been set for other
personal computers. Also, confirm the status of the radio
waves in case of trouble such as a network connection
failure.
■
Encryption Type
Displays the encryption type currently used by
the radio.
■
IP Address
Displays the current TCP/IP address assigned to
the WLAN adapter.
In the case of access point (infrastructure)
connection, enter the necessary data for
the access point before confirming
connection. Refer to the manual of the
access point for the access point setup
procedure.
On the Current Status tab, click the [Advanced] button.
The following information will be displayed.
■
Country
The country with the country code for which the
radio is configured.
Connecting your personal computer to another
personal computer
■
Transmit Power Level
Displays the current transmit power level of the
radio.
1. Click [Start] first and then [My Computer]. The
[My Computer] window will be displayed in the left
frame.
■
Network Name (SSID)
Displays the Network Name (SSID) currently
used by the radio.
2. Click [My Network Places] in the “Other Places”
list. The window [My Network Places] will be dis-
played.
■
Power Save Mode
Displays the configured Power Save Mode
currently used by the radio. [Off], [Normal], or
[Maximum] will be displayed.
3. Click [View workgroup computers] under Network
Tasks in the left frame.
4. Double-click the personal computer to which your
personal computer is to be connected. The folder
that was specified in “Setting the file-sharing func-
tion” on page 100 will be displayed.
■
BSSID
Displays the Basic Service Set Identifier. This is
typically the MAC address of the Access Point or
in the case of AdHoc networks, is a randomly
generated MAC address.
5. Double-click the folder to be accessed.
Confirming the status of the radio
■
Frequency
1. Right-click the Atheros icon in the lower right cor-
ner of the screen.
Displays the center frequency currently being
used by the radio.
2. Click [Open Client Utility]. The Atheros Client
Utility window opens.
■
Transmit Rate
Displays the current data rate used by the radio
to transmit data.
3. On the Current Status tab, you will find the current
operating status of the radio. (When the radio is
turned off or the computer is not yet connected,
some of the conditions will not be displayed.)
■
Receive Rate
Displays the current data rate used by the radio
to receive data.
■
Profile Name
The current configuration profile is displayed.
■
Network Type - Configured Network Type
[Access Point] or [AdHoc] will be displayed.
■
Current Mode
Indicates the frequency and data rate currently
used by the radio.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 102 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Connection using Atheros Client Utility
FLOW OF OPERATIONS
The wireless LAN connection procedure is outlined
below.
■
To use access point (infrastructure) con-
nection, refer to the access point manual
for the access point-setting procedure.
■
You do not need to set the channel
when using access point (infrastructure)
mode. Channel selection is controlled by
the access point. In ad hoc networks,
channel selection defaults to channel 11;
however, channel selection can be man-
ually changed if desired. This can be
accomplished only when using the client
utility.
1. Make sure that the personal computer is ready for
the transmission of radio waves from the wireless
LAN. For further details, see “Starting the trans-
mission” on page 96.
2. Assign the parameters required for wireless LAN
connection. For further details, see “Preparation
for wireless LAN connection” on page 97.
■
Enter the network name (SSID) and other data.
If it is necessary to change the channel,
change the setting of the access point.
For the setting procedure, refer to the
manual of the access point.
■
Enter the network key (the key to be used to
encode communications data).
3. Perform setting operations relating to network con-
nection. For further details, see “Connection to the
network” on page 99.
1. Right-click the Atheros Wireless Utility icon in the
system tray in the lower right corner of your screen.
■
Specify TCP/IP as the protocol, and confirm the
name of the work group and other settings.
2. Click [Open Client Utility]. The [Atheros Client
Utility] window will be displayed.
■
Enter the data required for file/printer sharing on
3. Select the [Profile Management] tab.
the network. Perform this operation as required.
4. Click the [New] button. The Profile Management
window will appear.
■
For access point (infrastructure) connection,
enter data for the access point. Refer to the
manual of the access point for further details.
5. Enter the following information required to estab-
lish connection to the wireless LAN:
■
Verify that you have been able to connect your
computer to the network.
Profile Name
Enter a name for this configuration profile
PREPARATION FOR WIRELESS LAN
CONNECTION
This section explains the preparation (parameter assign-
Network names
Enter the appropriate SSID(s) of the wireless net-
works to which this device will connect. You have
the option of entering up to three SSID’s.
ment) required for the use of the wireless LAN.
Assigning parameters
6. Select the [Advanced] tab.
Enter the network name (SSID), the network key, and
other data required for wireless LAN connection. If there
is the administrator of the network, contact the network
administrator for data settings.
7. Choose appropriate Power Save Mode setting.
Options are [Off], [Normal], and [Maximum].
[Normal] is the default setting.
8. Choose the appropriate type of network connec-
tion. Options are [Access Point] (same as infra-
structure mode) and [AdHoc].
9. Select the [Security] tab.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 103 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
10. Select the appropriate security method for your
wireless network.
2. Double-click the [Network and Dial-up Connec-
tions] icon. The [Network and Dial-up Connec-
tion] window will be displayed.
WPA
3. Right-click [Local Area Connection], and click
[Properties] in the menu displayed. The [Local
Area Connection Properties] window will be dis-
played.
Choose the appropriate WPA EAP type - PEAP or
TLS. Please see your network administrator for the
appropriate configuration settings.
4. Click [Internet Protocol (TCP/IP] and then click
[Properties]. The [Properties] window will be dis-
played.
WPA-PSK
Enter the appropriate pre-shared key. Please see
your network administrator for the appropriate
configuration settings.
5. Set the IP address:
■
For ad hoc connection
802.1x
Select [Use the following IP address:], then enter
data in [IP address] and [Subnet mask]. See
page 112 for IP address setting.
Choose the appropriate 802.1x/EAP type: TLS,
PEAP, or LEAP. Please see your network adminis-
trator for the appropriate configuration settings.
■
For access point (infrastructure) connection
Pre-Shared Key
Select [Obtain an IP address automatically] and
[Obtain DNS server address automatically].
Same as Network Key or WEP Key. Entry methods
include hexadecimal or ASCII text. If you wish to
use ASCII characters, enter the network key in a
string consisting of five or thirteen characters. The
characters that can be used for the Network Key
are: 0 - 9, A - Z, a - z, and _.
Follow directions from the network administrator
about IP address settings, DNS server setting, and
the default gateway.
6. Click the [OK] button. Processing will return to the
[Properties] window.
If you wish to use a hexadecimal number, enter the
network key in a string consisting of 10 to 26 char-
acters.The characters that can be used for the net-
work key are: 0 - 9, A - F, and a - f. For ad hoc
connections, enter the same network key for all
computers connected to the network. For access
point (infrastructure) connection, enter the value
to match the access point. For information about
the access point, refer to the access point manual.
7. Click the [OK] button. If a message is displayed
that requests you to restart the personal computer,
click [Yes] and then restart the computer.
Confirming the computer and workgroup names
To modify the computer name and/or the
workgroup name, you need to be logged
in from Windows as an administrator.
CONNECTION TO THE NETWORK
If there is the administrator of the network, contact the
network administrator for data settings prior to
connecting to the network.
1. Click [Start] -> [Control Panel].
2. Double-click the [System] icon. The [System Prop-
erties] window will be displayed.
Setting the network
3. Click the [Network Identification] tab.
Perform the “Setting TCP/IP” and “Confirming the
computer and work group names” operations for
network connection.
4. Confirm the settings of [Full computer name] and
[Work group].
■
The setting of [Full computer name] denotes the
name for identifying the computers on the
network. Any name can be assigned. The
computer name will be identified more easily if
the model number, the user name, and other
factors are already set.
Setting TCP/IP
To change the setting of the IP address,
you need to be logged in from Windows
as an administrator.
■
[Workgroup] denotes the group name of the
network.
1. Click [Start] -> [Control Panel].
103
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 104 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
5. To change the name, click [Properties], then pro-
ceed in accordance with the instruction messages
displayed on the screen. Processing will return to
the [System Properties] window.
will return to the [Wireless Network Connection
Properties] window, and [File and Printer Sharing
for Microsoft Networks] will be added to the list.
9. Click the [OK] button.
Setting the file-sharing function
For ad hoc connection:
Assign the same network name to all personal com-
puters existing on the network.
The procedure for setting the file-sharing function is laid
down below taking the “work” folder within drive C as
an example.
For access point (infrastructure) connection:
Assign the name of the workgroup to be accessed.
1. Double-click [My Computer] on the Desktop, and
then double-click [Local Disk (C:)].
6. Click the [OK] button. If a message is displayed
that requests you to restart the personal computer,
click [Yes].
2. Right-click the “work” folder (or whichever folder
you wish to share), and click [Sharing...] in the
menu displayed. The [Properties] window will be
displayed.
Setting the sharing function
Set the sharing function to make file and/or printer
sharing with other network-connected personal
computers valid. The setting operation is not required
unless the sharing function is to be used.
3. Select the [Sharing] tab if it isn’t already selected.
4. Select [Share this folder], then enter data as
required:
■
“Share name”
The folder and printer for which the sharing function
has been set will be usable from any personal computer
present on the network.
Enter the name of the folder to be shared.
■
“Comment”
Enter explanatory statements or notes about the
folder to be shared.
To share a file and/or the connected
printer, you need to be logged in as an
administrator.
■
■
“User limit”
Enter the number of users who share the folder.
[Permissions]
Setting the Microsoft network-sharing service
Click the [Permissions] button to set permission
levels for access to the folder.
1. Click [Start] -> [Control Panel].
2. Double-click the [Network and Dial-up Connec-
tions] icon. The [Network and Dial-up Connec-
tions] window will be displayed.
■
[Caching]
Click the [Caching] button to configure settings
for the off-line access to the folder.
3. Right-click [Local Area Connection], and click
[Properties] in the menu displayed. The [Proper-
ties] window will be displayed.
5. Click the [OK] button. The folder will be set as a
sharable folder, and the display of the icon for the
“work” folder will change.
4. If [File and Printer Sharing for Microsoft Net-
works] is displayed, proceed to step 5.
Setting the printer-sharing function
If [File and Printer Sharing for Microsoft Net-
works] is not displayed, skip to step 6.
1. Click [Start] -> [Printers]. A list of connected
printers will be displayed.
5. Make sure that the [File and Printer Sharing for
Microsoft Networks] check box is checked, and
then click the [OK] button. Skip to “Setting file-
sharing function” on page 100.
2. Right-click the printer for which the sharing func-
tion is to be set, and then click [Sharing...] in the
menu displayed. The property window correspond-
ing to the selected printer will be displayed.
6. Click [Install]. The [Select Network Component
Type] window will be displayed.
3. Click the Sharing tab if it is not already selected.
4. Check the [Shared as] checkbox and confirm the
name of the printer to be shared or enter a new
name. Click [OK]. Printer sharing will be set and
the display of the icon for the printer will change.
7. Click [Service], and then click the [Add] button.
The [Select Network Service] window will be dis-
played.
8. Click [File and Printer Sharing for Microsoft Net-
works] and then click the [OK] button. Processing
104
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 105 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
■
Confirming connection
IP Address
Displays the current TCP/IP address assigned to
the WLAN adapter.
After you have finished the network setup operations,
access the folder whose sharing has been set, and
confirm the status of the radio in case of trouble such as
a network connection failure.
On the Current Status tab, click the [Advanced] button.
The following information will be displayed.
In the case of an access point (infrastructure) connec-
tion, enter the necessary data for the access point before
confirming connection. Refer to the manual of the access
point for the access point setup procedure
■
■
■
■
Country
The country with the country code for which the
radio is configured.
Transmit Power Level
Displays the current transmit power level of the
radio.
Connecting your personal computer to another
personal computer
1. Double-click [My Network Places] on the Desktop.
The [My Network Places] window will be dis-
played.
Network Name (SSID)
Displays the Network Name (SSID) currently
used by the radio.
2. Double-click the [Computers Near Me] icon. The
personal computers connected to the network will
be listed.
Power Save Mode
Displays the configured Power Save Mode
currently used by the radio. [Off], [Normal], or
[Maximum] will be displayed.
3. Double-click the name of the personal computer to
which you wish to connect your own personal com-
puter. The folder that specified in “Setting the file-
sharing function” on page 100 will be displayed.
■
BSSID
Displays the Basic Service Set Identifier. This is
typically the MAC address of the Access Point or
in the case of AdHoc networks, is a randomly
generated MAC address.
4. Double-click the folder to be accessed. The contents
of the folder will be displayed.
Confirming the radio status
■
■
■
Frequency
1. Right-click the Atheros Wireless icon in the lower
right corner of the screen.
Displays the center frequency currently being
used by the radio.
2. Click [Open Client Utility]. The Atheros Client
Utility window opens.
Transmit Rate
Displays the current data rate used by the radio
to transmit data.
3. On the Current Status tab, you will find the current
operating status of the radio. (When the radio is
turned off or the computer is not yet connected,
some of the conditions will not be displayed.)
Receive Rate
Displays the current data rate used by the radio
to receive data.
■
Profile Name
The current configuration profile is displayed.
■
Network Type - Configured Network Type
[Access Point] or [AdHoc] will be displayed.
■
Current Mode
Indicates the frequency and data rate currently
used by the radio.
■
Current Channel
The channel number currently used by the radio.
■
Link Status
Displays the current connected state of the
WLAN module.
■
Encryption Type
Displays the encryption type currently used by
the radio.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 106 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Other settings
This setting is only effective during ad hoc connection; it
will be ineffective during access point connection.
SETTING OF POWER-SAVING FUNCTION
You can set the power-saving function of wireless LAN.
Default setting is auto-setting. In case of using the
power-saving function, manually control the communi-
cation performance.
When changing channels during ad hoc
connection, change the channel settings of
all connected computers with the same
Network name (SSID) at the same time.
After changing the channels, turn off all
computers and -- after they are all turned
off -- turn them back on.
Intel PROSet Wireless LAN:
1. Click [Start] -> [(All) Programs] -> [Intel Network
Adapters] -> [Intel(R) PROSet]. The Intel(R)
PROSet window will be displayed.
2. Click the [Adapter] tab.
Intel PROSet Wireless LAN:
3. Click the [Configure] button in [Power settings].
The [Power settings] window will be displayed.
1. Click [Start] -> [(All) Programs] -> [Intel Network
Adapters] -> [Intel(R) PROSet]. The Intel(R)
PROSet window will be displayed.
4. Select [Manual], and adjust the bar to set the
power-saving function.
2. Click the [Adapter] tab.
Setting of transmission power during ad hoc
connection
3. Click the [Configure] button in [Ad hoc settings].
The [Ad hoc settings] window will be displayed.
By controlling the transmission power during ad hoc
connection, you can broaden or narrow the communi-
cation range. This setting is only effective during ad hoc
connection. It will be ineffective during access point
connection.
4. Change channels during ad hoc connection by
selecting a new channel from the drop down list.
5. Click [OK].
Atheros Wireless LAN:
Intel PROSet Wireless LAN:
1. Click on the My Computer icon. Select [View sys-
tem information] from the left frame.
1. Click [Start] -> [(All) Programs] -> [Intel Network
Adapters] -> [Intel(R) PROSet]. The Intel(R)
PROSet window will be displayed.
2. Select the Hardware tab and click [Device Man-
ager].
2. Click the [Adapter] tab.
3. Double-click “Atheros BCM4306 Wireless LAN
Adapter” under [Network Adapters].
3. Click the [Configure] button in [Power settings].
The [Power settings] window will be displayed.
4. In the Atheros BCM4306 Wireless LAN Adapter
window, select the Advanced tab.
4. Adjust the “Transmission Power (Ad Hoc)” bar to
set the transmission power.
5. Select IBSS Channel Number from the list, and
change the value from the [Value:] dropdown list to
the desired channel.
Setting of channels during ad hoc connection
You can set channels during ad hoc connection. Channel
11 is set by default. When connecting to an existing ad
hoc network, no channel setting will be effective.
6. Click [OK].
106
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 107 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
Troubleshooting
Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the
following table.
Problem
Possible Cause
Possible Solution
Unavailable
network
connection
Ad hoc connection: verify that the network names (SSID’s) and network
keys (WEP) of all computers to be connected have been configured
correctly. SSID’s and WEP key values must be identical on each machine.
Access Point (Infrastructure) connection: set the network name (SSID)
and network key to the same values as those of the access point.
Incorrect network name
(SSID) or network key
Set the Network Authentication value identically to that of the Access
Point. Please consult your network administrator for this value, if
necessary.
For the method of setting network authentication, refer to the following
pages:· Windows XP: “Assigning parameters” on page 97·
Windows 2000: “Assigning parameters” on page 102
Ad hoc connection: Retry connection after shortening the distance to
the destination computer or removing any obstacles for better sight.
Access Point (Infrastructure) connection: Retry connection after short-
ening the distance to the access point or removing any obstacles for
better sight.
Poor radio wave
condition
To check the wave condition, refer to the following pages:· Windows
XP: “Confirming the status of the radio waves” on page 101.· Windows
2000: “Confirming the status of the radio waves” on page 105
Check if the wireless switch is turned ON. Also verify “Disable Radio” is
not checked in “Network setting” window. Refer to “Starting Transmis-
sion” on page 96.
Radio wave
transmission has
stopped
Check if the computer to be connected is turned ON.
The computer to be
connected is turned off
If there is any other wireless LAN network nearby, change channels to
avoid active channel duplication. For the method of checking active
channels, refer to the following pages:· Windows XP: “Confirming the
status of the radio waves” on page 101· Windows 2000: “Confirming
the status of the radio waves” on page 105
Active channel
duplication due to
multiple wireless LAN
networks
Check if you have a right of access to the network to be connected with.
No right of access to
the network to be
connected
Check the protocol, work group name or shared setting.
Incorrectly-performed
network setting
For the method of checking, refer to the following pages:· Windows XP:
“Connection to the Network” on page 99· Windows 2000: “Connec-
tion to the Network” on page 103
If the setting of [Network authentication (shared mode)] is not matched
with that of access point or computer to be connected with, no commu-
nication can be established. Check the parameter setting.Refer to
“Assigning parameters” on page 97.
Unmatched [Network
authentication (shared
mode)] settings in
Windows XP
107
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 108 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Problem
Possible Cause
Possible Solution
Retrieve computers as follow:
Unavailable
network
connection
Windows XP:
1. Click [Start] button, then click [Search].
2. Click [Computers or people].
3. Click [Computers on the network].
(continued)
It takes too long to
retrieve the network
and display the
4. Input the name of computer to be connected with in [Computer
name] and click [Search].
connected computers.
5. Double-click the icon of connected computer.·
Windows 2000:
1. Click [Start] -> [Find] -> [Files and folders].
2. Click [Computer] in [Find other items].
3. Input the name of computer to be connected with in [Computer
name] and click [OK].
4. Double-click the icon of connected computer.
Check the network setting.
Windows XP: “Setting the network” on page 99.
Windows 2000: “Setting the network” on page 103
In case of using TCP/IP protocol, you can check IP address as follows:
1. Windows XP:
Click [Start] -> [All programs] -> [Accessories] ->
[Command prompt].·
Windows 2000:
Click [Start] button -> [Program] -> [Accessories] ->
[Command prompt].
2. In [Command prompt] or [MS-DOS prompt] window, input
[IPCONFIG] command as follows, then press [Enter] key.
Incorrect setting of IP
address
Example: In case of C drive being the hard disk:
C:\ipconfig [Enter]
Check that the IP address is correctly displayed:.
IP Address................: 10.0.1.3
Subnet Mask.............: 255.255.255.0
Default Gateway.........: 10.0.1.1
When IP address is displayed as [169.254.XXX.YYY] or [0.0.0.0],
IP address is not correctly fetched from the access point. In that
case, restart the computer itself. If the display is still unchanged,
check the setting of TCP/IP.
If [Cable Disconnected] or [Media Disconnected] is displayed
without showing IP address, check the setting of network name
(SSID) and network key. Also, set the network authentication
according to the access point.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 109 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
Problem
Possible Cause
Possible Solution
Communication
is disconnected
soon after
In case of Windows XP, check the setting of “Enable network access
control using IEEE 802.1X”.Refer to “Assigning parameters” on
page 97.
connection to
the access point
When restricting the access of wireless LAN clients using IEEE802.1X
authentication, put a check mark on “Enable network access control
using IEEE 802.1X”.
Access control may be
disabled
When using at home, remove a check mark on “Enable network access
control using IEEE802.1X”.
For the method of setting related with IEEE802.1X authentication, refer
to the access point manual.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 110 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Wireless LAN Glossary
Ad hoc
the world. A private address is a unique address within a
closed network.
A designation for wireless LAN network configuration.
It indicates a form of communication limited to those
personal computers which have wireless LAN function.
For details, refer to “Ad hoc connection” on page 94.
LAN (Local Area Network)
An environment connecting computers within a rela-
tively small range, such as the same floor and building.
Channel
MAC address (Media Access Control Address)
The frequency band of wireless LAN to be used in
communications over wireless LAN or at the access
point.
A physical address inherent to a network card. For
Ethernet, the top three bytes are controlled/assigned as a
vendor code. The remaining three bytes comprise the
code uniquely (to avoid duplication) controlled by each
vendor. As a result, there is no Ethernet card with the
same physical address in the world. In Ethernet, the
frame transmission/reception is performed based on this
address.
DHCP (Dynamic Host Configuration Protocol)
A protocol used for automatically fetching communica-
tion parameters such as IP addresses. The side which
assigns IP address is called DHCP server and the side
that is assigned it is called DHCP client.
MTU (Maximum Transmission Unit)
DNS (Domain Name System)
The maximum size of data which can be transmitted at
one time in networks including the Internet. In an envi-
ronment whose maximum size of data is too large to
correctly receive data, normal communications can be
restored by setting the size of MTU to a smaller value.
A function that controls the correspondence of IP
addresses assigned to a computer with the name. Even
for those computers whose IP addresses are unknown, if
their names are known, it is possible to communicate
with them.
Network authentication
IEEE802.11a
The method of authentication performed by wireless
LAN clients to connect with the access point. There are
two types: open system authentication and shared key
authentication. The type of authentication must be set
to each client and also coincide with the setting of access
point with which to communicate. Network authentica-
tion is sometimes called authentication mode.
One of the wireless LAN standards prescribed by the 802
committee in charge of establishing standards of LAN
technology in IEEE (Institute of Electrical and Electronic
Engineers). It allows communications at the maximum
speed of 54 Mbps by using a 5GHz band which can
freely be used without radio communication license.
IEEE802.11b
Network key
One of the wireless LAN standards prescribed by 802
committee in charge of establishing standards of LAN
technology in IEEE (Institute of Electrical and Electronic
Engineers). It allows communications at the maximum
speed of 11Mbps by a band of 2.4 GHz (ISM band)
which can freely be used without radio communication
license.
Data that is used for encrypting data in data communi-
cation. The personal computer uses the same network
key both for data encryption and decryption, therefore,
it is necessary to set the same network key as the other
side of communication.
Network name (SSID: Security Set Identifier)
Access point
When a wireless LAN network is configured, grouping is
performed to avoid interference or data theft. This
grouping is performed with “Network name (SSID)”. In
order to improve security, the network key is set
allowing no communication unless “Network name
(SSID)” coincides with the network key.
A designation of Wireless LAN network configurations.
It indicates a form of communication using an Access
Point. For details, refer to “access point connection” on
page 94.
IP address
Open system authentication
An address used by computers for communicating in
TCP/IP environment. IP addresses have global and
private addresses. A global address is a unique address in
One of network authentication types for wireless LAN.
Since there is no check of network key upon authentica-
tion, clients can connect to the access point without
110
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 111 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
submitting correct network keys. However, in case of
actual communications, the same network key must be
set. Open system authentication is sometimes called
Open key authentication.
PPPoE (Point to Point Protocol over Ethernet)
A method of allowing the authentication protocol
adopted in telephone line connection (PPP) to be used
over an Ethernet.
Protocol
A procedure or rule of delivering data among
computers. Ordered data communication is allowed by
making all conditions required for communication
including the method of data transmission/reception
and actions upon communication errors into proce-
dures.
Shared key authentication
One of the network authentication types for wireless
LAN. Upon authentication, the access point checks
whether the same network key is set to the client. If the
client uses a wrong network key or the network key itself
is not set, authentication is unsuccessful, allowing no
communications with the access point.
SSID (Security Set Identifier)
See “Network name”
Subnet mask
TCP-IP network is controlled by being divided into
multiple smaller networks (subnets). IP address consists
of the subnet address and the address of each computer.
Subnet mask defines how many bits of IP address
comprise the subnet address. The same value shall be set
among computers communicating with each other.
TCP/IP (Transmission Control Protocol/Internet
Protocol)
A standard protocol of the Internet.
Wi-Fi
Indicates that the interconnectivity test of the organiza-
tion which guarantees the compatible connection of
wireless LAN (Wi-Fi Alliance) has been passed.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 112 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
IP address information
IP addressing is much more complicated
than can be briefly explained in this
document. You are advised to consult with
your network administrator for additional
information.
If IP address is unknown, set IP address as follows:
If you have an access point (DHCP server) on the
network, set the IP address as follows:
Windows 2000: [Obtain an IP address automatically]
Windows XP: [Obtain an IP address automatically]
A DHCP server is a server that
automatically assigns IP addresses to
computers or other devices in the network.
There is no DHCP server for the AdHoc
network.
If the IP address is already assigned to the computer in
the network, ask the network administrator to check the
IP address to be set for the computer.
If no access point is found in the network:
An IP address is expressed with four values in the range
between 1 and 255.
Set the each computer as follows: The value in paren-
theses is a subnet mask.
<Example>
Computer A: 192.168.100.2 (255.255.255.0)
Computer B: 192.168.100.3 (255.255.255.0)
Computer C: 192.168.100.4 (255.255.255.0)
:
:
Computer X: 192.168.100.254 (255.255.255.0)
112
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 113 Thursday, February 19, 2004 4:52 PM
W I r e l e s s L A N U s e r ’s G u i d e
Specifications
Item
Specification
Type of network
Conforms to IEEE 802.11a/802.11b/g (Wi-Fi based)*
Transfer rate
(Automatic switching)
54 Mbps maximum data rate
Active frequency
Number of channels
Security
802.11b/g: 2400~2473 MHz
802.11a: 4900 ~ 5850 MHz
802.11a: 8 independent channels
802.11b/g: 11 channels, 3 non-overlapping channels
Encryption Types - WEP, TKIP, AES**
WPA 1.0 compliant
Encryption Keylengths Supported: 64 bits, 128 bits, and
152 bits (Atheros module using AES encryption only)
802.1x/EAP
CCX 1.0 compliant
10 units or less ***
Maximum recommended number of computers to be
connected over wireless LAN (during ad hoc
connection)
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of
wireless LAN (Wi-Fi Alliance) has been passed.
** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/
104 bits after subtracting the fixed length of 24 bits.
*** Depending on practical environments, the allowable number of computers to be connected may be decreased.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 114 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Using the Bluetooth Device
The Integrated Bluetooth module is an optional device
available for Fujitsu mobile computers.
WHAT IS BLUETOOTH
Bluetooth technology is designed as a short-range wire-
less link between mobile devices, such as laptop
computers, phones, printers, and cameras. Bluetooth
technology is used to create Personal Area Networks
(PANs) between devices in short-range of each other.
WHERE TO FIND INFORMATION
ABOUT BLUETOOTH
The Bluetooth module contains a robust Help user’s
guide to assist you in learning about operation of the
Bluetooth device.
To access the Help file, click [Start] -> All Programs, and
click on Toshiba. Select Bluetooth, then select User’s
Guide.
For additional information about Bluetooth Technology,
visit the Bluetooth Web site at: www.bluetooth.com.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20 centimeters between the Wire-
less LAN/Bluetooth antenna (located on the top edge of
the LCD screen) and your body.
The transmitters in this device must not be co-located or
operated in conjunction with any other antenna or
transmitter.
Canadian Notice
To prevent radio interference to the licensed service, this
device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject
to licensing.
Warranty
Users are not authorized to modify this product. Any
modifications invalidate the warranty.
This equipment may not be modified, altered, or
changed in any way without signed written permission
from Fujitsu. Unauthorized modification will void the
equipment authorization from the FCC and Industry
Canada and the warranty.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 117 Thursday, February 19, 2004 4:52 PM
I n d e x
Index
CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39, 83
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56, 57
A
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Centrino . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CMOS RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Cold-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
COMM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . 10, 77
Connection using Atheros Client Utility . . . . . . . . . 102
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . 6
Conventions Used in the Guide . . . . . . . . . . . . . . . . . . 1
CRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
AC
adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
ACPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Active-Matrix Display . . . . . . . . . . . . . . . . . . . . . . . . . 83
Anti-theft lock slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . .27, 83
Automatically Downloading Driver Updates . . . . . . 67
B
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
charging indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 12
cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
dead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
lithium ion battery . . . . . . . . . . . . . . . . . . . . . . .37, 85
low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60, 61
recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
D
DC Output Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DC Power Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Default Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50, 78
DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45, 84
Disk
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 28
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
power management . . . . . . . . . . . . . . . . . . . . . . . . . 28
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Bluetooth
Using the Bluetooth Device . . . . . . . . . . . . . . . . . .114
Where to Find Information . . . . . . . . . . . . . . . . .114
Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
DMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Dolby Headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Drive Image Special Edition (DISE) . . . . . . . . . . . . . . 66
Drivers and Application CD . . . . . . . . . . . . . . . . . . . . 67
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
C
Cache Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
CapsLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CardBus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
117
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 118 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
DVD drive
H
access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
tray release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Hard Disk Drive
access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
DVD/CD-RW combo . . . . . . . . . . . . . . . . . . . . . . . . . 39
DVD/CD-RW/CD-ROM
access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 52
DVD/CD-RW/CD-ROM drive
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56, 57
Hibernation Feature . . . . . . . . . . . . . . . . . . . . . . . . . . .33
disable/enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
DVD-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
I
E
IDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 51
Internal LAN Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51, 85
IRQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
ECP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Emergency tray release . . . . . . . . . . . . . . . . . . . . . . . . . 8
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Extended Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
External Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . 42
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
K
External Monitor Port . . . . . . . . . . . . . . . . . . . . . . 7, 52
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6, 13
cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
F
FDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Flexible Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 18
cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
eject lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
L
LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
LifeBook Security Application Panel
Floppy Disk
buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
configuring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
deactivating and activating . . . . . . . . . . . . . . . . . . .23
launching applications . . . . . . . . . . . . . . . . . . . . . . .22
operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
ejecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
preparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
write protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . 1
Fujitsu Driver Update utility . . . . . . . . . . . . . . . . . . . 67
LifeBook Security/Application Panel . . . . . . . . . . . . . .6
Fujitsu LifeBook
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
M
Media Player
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39, 40
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Function Key
F3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 17
F9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 17
FN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Media player
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Memory
118
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 119 Thursday, February 19, 2004 4:52 PM
I n d e x
capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
compartment . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 45
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45, 46
upgrade module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Power
AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Auto/Airline adapter . . . . . . . . . . . . . . . . . . . . . . . . 27
failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59, 60
indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 52
MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Power Management . . . . . . . . . . . . . . . . . . . . . . . . 32, 33
Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . 29, 64
Power/Suspend/Resume Button . . . . . . . . . . . . . . . 6, 32
Modem Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Modem Result Codes . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Modular Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . . 79
Adobe Acrobat Reader . . . . . . . . . . . . . . . . . . . . . . 79
BatteryAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Drive Image Special Edition (DISE) . . . . . . . . . . . 80
Fujitsu HotKey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Intel SpeedStep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
LifeBook Application Panel . . . . . . . . . . . . . . . . . . 80
manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Netscape 6.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Quicken New User Edition . . . . . . . . . . . . . . . . . . . 80
Mouse
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
MPU-401 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
N
NTSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NumLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Preparation for wireless LAN connection (XP) . . . . 97
PS/2 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
R
O
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 31
Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Restoring Your Pre-installed Software . . . . . . . . . . . . 66
RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Optical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
P
Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50, 86
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58, 59
PC Card
access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
S
ScrLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 45
Security Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Security Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PCMCIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51, 87
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58, 59
Pointing Device
See Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SMART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
back panel components . . . . . . . . . . . . . . . . . . . . . . 47
connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
detaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . 79
Environmental Requirements . . . . . . . . . . . . . . . . 79
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
119
Download from Www.Somanuals.com. All Manuals Search And Download.
S Series.book Page 120 Thursday, February 19, 2004 4:52 PM
L i f e B o o k S 7 0 0 0 N o t e b o o k
Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Intel PROSet Wireless LAN . . . . . . . . . . . . . . . . . . .94
IP address information . . . . . . . . . . . . . . . . . . . . . .112
Other settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Setting of power-saving function . . . . . . . . . . . . .106
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Starting Transmission . . . . . . . . . . . . . . . . . . . . . . .96
Stopping transmission . . . . . . . . . . . . . . . . . . . . . . .96
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Wireless LAN Glossary . . . . . . . . . . . . . . . . . . . . . .110
SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . 6, 11
Stereo Line-in Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Stereo Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Super-Multi DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Super-Multi DVD drive . . . . . . . . . . . . . . . . . . . . . . . 39
Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
T
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Touchpad Pointing Device . . . . . . . . . . . . . . . . . . . . . . 6
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
U
Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . . . . . 51
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51, 58
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58, 59
USB 2.0 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9
V
Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
W
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
WFM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Windows
Windows 2000 Professional . . . . . . . . . . . . . . . . . . . 1
Windows XP Home . . . . . . . . . . . . . . . . . . . . . . . . . 1
Windows XP Professional . . . . . . . . . . . . . . . . . . . . 1
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Start keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wireless LAN
Ad Hoc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Before Using the Wireless LAN . . . . . . . . . . . . . . . 94
Broadcom Wireless LAN . . . . . . . . . . . . . . . . . . . . 94
For better communications . . . . . . . . . . . . . . . . . . 95
Infrastructure Mode . . . . . . . . . . . . . . . . . . . . . . . . 95
120
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Eizo Computer Monitor L661 User Manual
Essick Air Humidifier E27 000 User Manual
Euro Pro Carpet Cleaner SC505H User Manual
Festool Saw PSB 300 Q User Manual
Frigidaire Dishwasher FGHD2465NB User Manual
GE Clothes Dryer DCCD330GG User Manual
Geemarc Caller ID Box Cordless Caller Display Unit User Manual
Generac Power Systems Portable Generator 005261 1 005262 1 User Manual
GE Washer WBVH5300KWW User Manual
Gianni Industries Door DG 30 User Manual