TROUBLESHOOTING
Before seeking repair or replacement, we recommend that you review the following:
LOUD NOISES: (Other than those during grinding of
small bones and fruit pits): These are usually caused by
accidental entry of a spoon, bottle cap or other foreign
object. To correct this, turn off electrical switch and water.
After disposer has stopped, remove *splash guard, remove
object with long handled tongs, and replace *splash guard.
IF TURNTABLE DOES NOT ROTATE FREELY:
Turn off disposer, then check for any foreign object lodged
between the turntable and grind ring. Dislodge object by
rotating table with a wooden broom handle and remove
object. (see 8B) If no foreign object is present, there may
be internal problems.
UNIT DOES NOT START: Unplug power cord or turn
either the wall switch or breaker box switch to “OFF”
LEAKS: If the unit leaks at the top, it may be due to:
1. Improper seating of sink flange (gasket centering, putty
or tightening).
2. Support ring not tightened properly.
3. Defective or improperly installed cushion mount.
position, depending on your model and wiring configuration.
Remove stopper and/or *splash guard. Check to see if
turntable will rotate freely using a wooden broom handle. If
turntable rotates freely, replace *splash guard and check re-
set button to see if it has been tripped. Re-set button is red
and located opposite discharge elbow, near the bottom (see
8A). Push button in until it clicks and remains depressed.
If unit leaks at the waste elbow, leak may be due to im-
proper tightening of elbow flange screws.
8A
8B
If re-set button has not been tripped, check for shorted or
broken wire connecting to disposer. Check electrical power
switch, fuse box or circuit breaker. If wiring and electrical
components are intact, the unit may have internal problems
that require service or replacement.
*Splash guard not used on Top Control/Batch Feed unit.
Call our toll free Help Line with any questions
800-944-9044
CLEANING AND MAINTENANCE
DO NOT ATTEMPT TO LUBRICATE YOUR DISPOSER!
The motor is permanently lubricated. The disposer is self
cleaning and scours its internal parts with each use.
Mineral deposits from your water can form on the stainless
steel turntable, giving the appearance of rust. DO NOT BE
ALARMED, the stainless steel turntables used will not
corrode.
NEVER put lye or chemical drain cleaners into the disposer,
as they cause serious corrosion of metal parts. If used,
resulting damage can be easily detected an all warranties
are void.
8
560C525P02 REV A
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT REGISTRATION
Bill of sale, sales slip, cancelled check or other purchase
record should be kept to verify the original purchase date for
warranty purposes.
See insert for specific information about your new
disposer:
NOTE: This Food Waste Disposer has been designed to
operate on 110-120 Volt, 60Hz exclusively. Using any other
voltage or Hz adversely affects performance.
Model Number*
IMPORTANT: Read all instructions thoroughly. Keep this
guide for future reference.
Serial Number*
CAUTION: Be sure to review SAFETY INSTRUCTIONS
FIRST PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK
OR INJURY TO PERSONS before using disposer.
*Above information appears on the label affixed to bottom of
the disposer. For your convenience, write down the model and
serial numbers prior to installation.
Call our toll free Help Line with any questions:
800-944-9044
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS.
SAVE THESE INSTRUCTIONS.
Note: if you are not familiar with electrical power and procedures, call a qualified electrician.
Warning: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check
with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not
modify the plug provided with the appliance if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
Warning: When using electrical appliances, basic precautions should always be followed, including the following:
1. Read all instructions before using the appliance.
2. To reduce the risk of injury, close supervision is neces-
sary when an appliance is used near children.
3. Do not put fingers or hands into a waste disposer.
4. Turn the power switch to the off position before at-
tempting to clear a jam or remove an object from the
disposer.
7. To reduce the risk of injury by materials that may be
expelled by a waste disposer, do not put the following
into a disposer: clam or oyster shells; caustic drain
cleaners or similar products; glass, china or plastic;
large whole bones; metal, such as bottle caps, tin cans,
aluminum foil or utensils; hot grease or other hot
liquids; whole cornhusks.
5. When attempting to loosen a jam in a waste disposer,
use a long wooden object such as a wooden spoon or
the wooden handle of a broom or mop.
8. When not operating a disposer, leave the stopper in
place to reduce the risks of objects falling onto the
disposer.
6. When attempting to remove objects from a waste
disposer use long-handled tongs or pliers. If the dis-
poser is magnetically actuated, non-magnetic tools
should be used.
9. DO NOT operate disposer unless splash guard is in
place. (Does not apply to the Top Control/Batch Feed
units.)
10. For proper grounding instructions see the ELECTRICAL
CONNECTION portion of this manual.
©2009 Electrolux Home Products, Inc.
All rights reserved. Printed in the USA
2
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVAL OF OLD UNIT
TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY
Caution: Be sure to support the disposer while
perfomring this step or it may fall when the
mounting ring is disconnected from the mounting
assembly. If your disposer is hard wired (metal
shielded cable not utilizing a wall plug), complete
steps C and D. If you utilize a plug- in cord, go
on to step E.
Before starting this step, turn off electrical power
at the circuit breaker or fuse box.
If your old mount is the same as the mount on your new
disposer, just reverse the assembly instructions found in
section Installation of Mounting Assembly. If your new
mount system is different, follow these instructions:
A. Use a pipe wrench to disconnect drain line where it
attaches to disposer discharge tube (see A).
C. When disposer is removed, turn up side down and
remove electrical cover plate (see D).
B. Remove disposer from sink flange by turning mount ring
to the left clockwise (see B). If you are unable to turn
the mount ring, tap on one of the extensions from the
ring with a hammer. Some mounting systems have
tubular extensions. Inserting a screwdiver into on tube
will provide additional leverage for turning the mount
ring (see B). Some disposers may require the removal
or loosening of nuts from the mount screws (see C).
Some disposers may require the removal of a clamp.
D. Use screwdriver to remove green ground wire. Remove
wire nuts from black and white power wires and
separate disposer wires from power cable wires.
Loosen screws on cable clamp and separate cable from
disposer.
E. To remove remaining mount system from the sink,
loosen mount screws, push mount ring up. Under it is
the snap ring. Use screwdriver to pop off ring (see E).
Remove mount ring, protector ring and gasket from sink
flange. Some mounts will require the unscrewing of a
large ring holding the sink flange in place. Pull sink
flange up through sink and clean off old putty from sink.
IMPORTANT: Unless you have a new home, this is a
good time to clean out the trap and drain lines by
running a drain auger or plumber’s snake before
installing your new disposer.
A
B
C
D
E
DISHWASHER CONNECTION
If you are utilizing a dishwasher, complete the following
procedure. If dishwasher is not to be connected go to
section Installation of Mounting Assembly.
*AIR GAP
B
A. Using a blunt instrument (steel punch or wooden dowl),
knock out entire plug (see A). Do not use a screwdriver
or sharp instrument. When knockout plug falls into
disposer, you may remove it or simply grind it up when
the disposer is used. This will not damage the disposer
in any way, but may take sometime to grind, over the
course of several uses. Go to section Installation of
Mounting Assembly.
DISHWASHER
HOSE
A
KNOCK
OUT PLUG
DISPOSER
RUBBER
HOSE
*Air gap may not be required
for all installations. Check local
plumbing codes.
B. Connect dishwasher hose using hose clamp. If hose size
is different, you will need a Dishwasher Connector Kit
(see B). Make sure all plumbing connections are tight
and in accordance with all plumbing codes and ordinan-
ces. Run water and check for leaks.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION OF MOUNTING ASSEMBLY
G
Rubber Gasket
Stopper
A
Sink Flange
B
H
Lower Mounting
Ring
Fiber Gasket
C
Backup Flange
D
Dishwasher Inlet
Mounting Ring
E
Disposer
Hush Cushion®
Snap Ring
F
NOTE: Hush Cushion included between mounting
ring and lower mounting ring.
Mount System
READ COMPLETELY BEFORE STARTING
NOTE: Pay close attention to the order of mount assembly parts, as they have been correctly assembled by the factory.
E. Tighten the 3 mounting screws evenly with a
screwdriver (see E). DO NO OVERTIGHTEN! Trim off
excess putty.
A. Disassemble the mounting assembly, as it has been
shipped, by turning the sink flange assembly until the
projections align with the notches in the lower mount
ring and allow you to pull the sink flange up and out of
the remaining lower mount assembly. Note the
A
SINK
sequence of these parts as they are stacked to identify
each part. Unscrew the 3 mount screws until the
mounting ring can be moved to the top of the back up
flange. Remove the snap ring with a screw driver.
STOPPER*
SINK FLANGE**
PLUMBER’S
PUTTY
B. Keep these assembled parts together and set aside.
Before you connect the disposer to the mount
assembly under the sink. Make sure the lower
mounting is in place and the hush cushion is engaged
properly to the top of the hopper.
RIDGE
FIBER GASKET
BACKUP FLANGE
C. Be sure your sink is clean. Pack the underside rim of
the sink flange with plumber’s putty. Position the sink
flange so it is centered and readable as you look into
your sink. Push the sink opening to make a good seal.
DO NOT move or rotate the sink flange once seated or
the seal may be broken.
MOUNTING RING
SNAP RING
RUBBER
GASKET
D. Take the remaining portion of the mount assembly, as it
was set aside and make sure that the rubber gasket is
on top of the protector ring. From under the sink, while
holding the sink flange firmly with one hand, line up the
notches in the mount ring with the projections of the
sink flange. Slide the mount assembly up onto the sink
flange. Slide the mount assembly up onto the sink
flange, past the projections
RESET BUTTON
*
Batch Feed Stopper looks different than the stopper illustrated.
** Mount Assembly
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION OF MOUNTING ASSEMBLY
YOUR DISPOSER COMES WITH THE FOLLOWING MOUNT SYSTEM
1
6
2
1
1
3
5
4
A
B
C
D
E
Mount System
READ COMPLETELY BEFORE STARTING
NOTE: Pay close attention to the order of mount assembly parts, as they have been correctly assembled by the factory.
D. Place a weight such as a disposer on the sink flange to
hold it in place. Use a towel to prevent scratching sink.
Pull snap ring open adn press firmly unitl it snaps into
place.
A. Evenly apply 1/2” thick rope of plumber’s putty around
flange (1).
B. Press Flange (1) firmly into sink drain. Remove excess
putty.
E. Tighten the 1 2/3” screws (3) evenly and firmly against
backup flange. Use shorter screws if sink is more than
3/8” thick.
C. Insert fiber gasket (2), backup flange (3) and mounting
ring (5). Hold in place while inserting snap ring (6).
Grounding Instructions
FOR WASTE DISPOSERS NOT EQUIPPED WITH A
GROUNDED PLUG-IN POWER CORD.
FOR WASTE DISPOSERS EQUIPPED WITH A
GROUNDED PLUG-IN POWER CORD.
This appliance must be grounded. In the event of a
malfunctionorbreakdown, groundingprovidesapathof
least resistance for electric current to reduce the risk of
electric shock. The power cord (to be installed) must have
anequipment-groundingconductorandagroundingplug.
The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordiances. Disconnect electric power to
disposercircuitbeforeinstallation. Turnthecircuit
breaker to the OFF position or remove the fuse.
This appliance must be grounded. In the event of a
malfunctionorbreakdown, groundingprovidesapathof
least resistance for electric current to reduce the risk of
electric shock. This appliance is equipped with a cord
havinganequipment-groundingconductorandagrounding
plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with all
local codes and ordinances.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CONNECTIONS
Wiring Disposer Directly to House Current
A. Connect disposer to 110-120 Volt, 60Hz AC current
only.
This appliance must be connected to a grounded, metal
permanent wiring system or an equipment grounding con-
ductor must be run with the circuit conductors and connected
to the equipment-grounding terminator or lead on the
appliance.
B. If plug-in cord is used, use a three prong plub (see A).
Ground wire should be attached to the ground screw in
the bottom of the end bell (see B).
C. Use a cable clamp strain relief connector where power
cord enters the disposer (see C).
A. If you use BX cable:
1. Install cable connector in hole.
2. Connect white wire to white lead of disposer.
3. Connect black.
Trace lead connected to this blade
and attach that lead to white wire
A
RIBBED SIDE
4. Connect bare ground.
on disposer.
NOTE: When viewing face of electical
plug with grounding pin at top,
the larger left blade is connected to
the identified wire.
If BX cable is not used, provide a serpareate ground wire to
nearest cold water metal pipe or other suitable ground, using
the screw in the bottom of the end bell for the ground wire
(see C).
B
C
RED RESET BUTTON
STRAIN
RELIEF
GROUND SCREW
WIRE NUTS
B. If your power supply does not include a ground wire, you
must provide one unless metal cable is used. Attach a
copper wire securely to disposer ground screw and attach
other end of wire to a metal cold water pipe. Use only UL
approved ground clamp. If plastic pipe is used in your home,
a qualified electrician should install a proper ground.
TO HOUSE
CURRENT OR
POWER CORD
REMOVE COVER
PLATE
NUT
ATTACHING DISCHARGE ELBOW/ CONNECTING DISPOSER TO MOUNT
ASSEMBLY
A. Connect waste elbow to the disposer (see A), proceed
to set B and C then connect bottom of the elbow by
tightening the slip nut (see D).
A
B
RUBBER
GASKET
If you are connecting to a dishwasher, return to section
(B) page 3. If not, make sure all plumbing connections
are tight and in accordance with all plumbing codes and
ordinances. Run water and check for leaks.
B. Hang disposer by aligning 3 mounting tabs with slide-up
ramps on mounting ring.
D
C
C. Turn mounting ring until all 3 mounting tabs lock over the
rides on the slide-up ramps.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
The Anti-Jam Swivell Impellers make a clicking sound as they swing into place. This indicates normal operation.
that the disposer slows down while grinding. The
disposer is actually increasing torque (grinding power)
and is operating under normal conditions.
A. Remove sink stopper. Turn on a medium flow of cold
water.
B. Turn switch to ON position; your motor is turning at full
speed and ready to use.
C. Scrape in food waste. Down the drain go table scraps,
peelings, rinds, seeds, pits, small bones and coffee
grounds. to speed up food waste disposal, cut or break
up large bones, rinds and cobs. Large bones and fibrous
husks require considerable grinding time and are more
easily thrown away with other trash. Do not be alarmed
D. Before turning disposer off, let water and disposer run
for approximately 15 seconds after shredding stops.
This assures that all waste is thoroughly flushed through
trap and drain.
E. It is not recommended to use hot water while running
disposer. Cold water will keep waste and fats solid so
disposer can flush away particles.
BATCH FEED OPERATING INSTRUCTIONS
The Anti-Jam Swivel Impellers make a clicking sounds as they swing into place. This indicates normal
operation.
A. Remove sink stopper and turn on a medium flow of cold
A
water.
B. Scrape in food waste. Down the drain go table scraps,
vegetable peelings, cobs, rinds, pits, bones and coffee
grounds. (see A)
C. Insert stopper to start disposer. (see B) One of the two
small slots in stopper base must line up with switch
plunger inside the neck of the disposer. Push down
firmly to turn the disposer on. Lift stopper to shut the
disposer off.
D. Run disposer for 15 seconds after shredding stops. This
B
assures that all waste is thoroughly flushed through the
drain.
E. To fill sink, insert stopper and align the largest slot with
the switch plunger. (see C) Push down to seal sink
without starting the disposer. When medium sized slot
(see B) in stopper base is lined up with the switch
plunger, water, can drain, but tableware, etc., cannot be
SMALL
SLOT
accidentally dropped into disposer.
MEDIUM
SLOT
TIPS FOR SUCCESSFUL OPERATION
A. Be sure disposer is empty before using your dishwasher
so it may drain properly.
B. You may want to leave the stopper in the drain when not
in use to prevent utensils and foreign objects from falling
into the disposer.
C
C. Your disposer is ruggedly built to give you many years of
trouble free service. It will handle all normal food
wastes, but it will NOT grind or dispose of such items as
plastic, tin cans, bottle caps, glass, china, leather, cloth,
rubber, string, clam and oyster shells, aluminum foil or
feathers.
LARGE
SLOT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|