Use & Care Manual
Freezer
Product Registration
2
2-3
3 - 4
4
Important Safety Instructions
First Steps
Energy Saving Ideas
Setting
the Temperature Control
4 - 5
5 - 7
7 - 8
8
Freezer Optional Features
Care and Cleaning
Power Failure/Freezer Failure
Avoid Service Checklist
Warranty
9 - 10
11
297281400 (October 2008)
READ AND SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
ElECTRICAl INFORMATION
FIRST STEPS
These guidelines must be followed to ensure that safety
mechanisms in the design of this freezer will operate prop-
erly.
This Owner’s Guide provides specific operating instruc-
tions for your model. Use the freezer only as instructed in
this Owner’s Guide. Before starting the freezer, follow
these important first steps.
•
Refer to the serialplate for correct electrical rating.
The power cord of the appiiance is equipped with a
three prong plug for your protection against shock
hazards. It must be plugged directly into a properly
groundedthree prong receptacle, protected with a 15
amp timedelay fuse or circuit breaker. The receptacle
must be installed in accordance with local codes
and ordinances. Consult a qualified electrician.
Receptacles protected by Ground Fault Interrupters
(GFI) are NOT RECOMMENDED. DO NOT USE AN
EXTENSION CORD OR ADAPTER PlUG.
INSTAllATION
•
•
Choose a place that is near a grounded electrical
outlet. Do Not use an extension cord or an adapter
plug.
For the most efficient operation, the freezer should
be located where surrounding temperatures will not
exceed 110°F (43°C). Temperatures of 32°F (0°C) and
below will NOT affect freezer operation. Additional
compressor heaters are not recommended.
•
If voltage varies by 10% or more, freezer performance
may be affected. Operating freezer with insufficient
power can damage the motor. Such damage is
not covered under the warranty. If you suspect your
household voltage is high or low, consult your power
company for testing.
•
Allow space around the unit for good air circulation.
Leave a 3 inch (75 mm) space on all sides of the
freezer for adequate circulation.
•
•
To prevent the freezer from being turned off
accidentically, do not plug unit into an outlet controlled
by a wall switch or pull cord.
Do not pinch, knot, or bend the cord in any manner.
OThER PRECAUTIONS
•
•
To defrost freezer, always unplug unit first.
Never unplug the freezer by pulling on the cord.
Always grip the plug firmly, and pull straight out from
the receptacle.
•
Turning the temperature control to OFF turns off the
compressor, but does not disconnect the power to the
light bulb or other electrical components.
NOTE: The exterior walls of the freezer may become quite
warm as the compressor works to transfer heat from the
inside. Temperatures as much as 30° F warmer than room
temperature can be expected. For this reason it is particu-
larly important in hotter climates to allow enough space for
air circulation around your freezer.
Avoid fire hazard or electric
shock. Do not use an extension cord or
an adapter plug. Do not remove any
prong from the power cord.
lEVElING
Grounding type
wall receptacle
The freezer must have all bottom corners resting firmly on
a solid floor. The floor must be strong enough to support
a fully loaded freezer. NOTE: It is VERY IMPORTANT for
your freezer to be level in order to function properly. If the
freezer is not leveled during installation, the door may be
misaligned and not close or seal properly, causing cooling,
frost, or moisture problems.
Do not, under any
circumstances,
cut, remove,
or bypass the
grounding prong.
To level Upright Models:
After discarding crating screws and wood base, use a car-
penter’s level to level the freezer from front-to-back. Adjust
the plastic leveling feet in front, ½ bubble higher, so that
the door closes easily when left halfway open.
Power supply
cord with 3-prong
grounding plug
FI3RST
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR REMOVAl (NON-ElECTRONIC MODElS)
If door must be removed:
Tu r n
Left To
Raise
1. Gently lay freezer on its back, on a rug or blanket.
2. Remove two base screws and base panel.
3. Remove bottom hinge screws.
Tu r n
Right To
Lower
Plastic
4. Remove plastic top hinge cover.
Leveling Feet
5. Remove screws from top hinge.
Crating
Screw
6. Remove top hinge from cabinet.
7. Remove door and bottom hinge from cabinet.
8. To replace door, reverse the above order and
securely tighten all screws to prevent hinge slippage.
DOOR REMOVAl (ElECTRONIC MODElS)
Discard The (4) Crating Screws
And (2) Wood Bases
If door must be removed:
•
Door hinge is fastened with tamper-proof screws.
Please have a qualified technician remove the door.
Unpacking and Leveling -- Upright Models
ENERGY SAVING TIPS
To level Chest Models:
If needed, add metal or wood shims between foot pads
and floor.
•
The freezer should be located in
the coolest area of the room, away
from heat producing appliances
or heating ducts, and out of direct
sunlight.
M
ClEANING (PRIOR TO USE)
•
Wash any removable parts, the freezer interior, and
exterior with mild detergent and warm water. Wipe dry.
Do not use harsh cleaners on these surfaces.
•
Let hot foods cool to room
temperature before placing in the
•
Do not use razor blades or other sharp instruments,
which can scratch the appliance surface when
removing adhesive labels. Any glue left from the tape
can be removed with a mixture of warm water and mild
detergent, or touch the residue with the sticky side
of tape already removed. Do not remove the serial
plate.
freezer. Overloading the freezer forces the compressor
to run longer. Foods that freeze too slowly may lose
quality or spoil.
•
•
•
Be sure to wrap foods properly, and wipe containers
dry before placing them in the freezer. This cuts down
on frost build-up inside the freezer.
Freezer shelves should not be lined with aluminum foil,
wax paper, or paper toweling. Liners interfere with cold
air circulation, making the freezer less efficient.
To allow door to
close and seal properly, DO NOT let
food packages extend past the front
of shelves.
Organize and label food to reduce door openings and
extended searches. Remove as many items as needed
at one time, and close the door as soon as possible.
SETTING ThE TEMPERATURE CONTROl
COOl DOwN PERIOD
•
For safe food storage, allow 4 hours for the freezer to
cool down completely. The freezer will run continuously
for the first several hours. Foods that are already
frozen may be placed in the freezer after the first few
hours of operation. Unfrozen foods should NOT be
loaded into the freezer until the freezer has operated
for 4 hours.
Shelf Front
•
When loading the freezer, freeze only 3 pounds of
fresh food per cubic foot of freezer space at one time.
Distribute packages to be frozen evenly throughout the
freezer. It is not necessary to turn the control knob to a
colder setting while freezing food.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
every five minutes until the freezer temperature is
below 23°F. To silence the buzzer, press the ALARM
RESET button.
TEMPERATURE CONTROl
Electromechanical Temperature Control (Chest and
Some Upright Models)
•
Door Ajar Alarm
The electromechanical temperature control is located in-
side the freezer on upright models, and on the left exterior
wall on chest models (see figure 1). The temperature is
factory preset to provide satisfactory food storage tem-
peratures. However, the temperature control is adjustable
to provide a range of temperatures for
This feature provides a warning if the the door is open
for more than five minutes. There will be a beep every
five seconds and the “Door Ajar” indicator will light up.
Press “Alarm Reset” to turn the alarm off. The “Door
Ajar” indicator will remain lit unril the door is closed.
If the door remains open for 15 minutes or more, the
interior lamp will turn off.
your personal satisfaction. To adjust
the temperature setting, turn the
temperature control knob clockwise
or counter clockwise. Allow several
hours for the temperature to stabilize
between adjustments.
Should an “E” appear on display, contact your authorized
service technician for repair. Until changes are made,
freezer will continue to run.
Deluxe Electronic Temperature Control (Some Upright
Frost Free Models)
Figure 1
Refer to the Electronics Control Guide supplied when you
purchase a deluxe electronic upright model. See Figure 3
for deluxe electronics control panel.
Standard Electronic Temperature Control (Some Up-
right Frost Free Models)
The standard electronic temperature control is located
outside the freezer (see Figure 1). Temperature is factory
preset to provide satisfactory food storage temperatures.
∧
To adjust the temperature setting, move the UP ( ) symbol
for colder temperatures and DOWN ( ) symbol for warmer
∨
temperatures on the control panel. Allow several hours for
the temperature to stabilize between adjustments.
To turn off freezer, press DOWN ( )
∨
symbol until display shows “1”. Press
three more times until display shows “0”.
∧
To activate freezer, press UP ( ) three
times until display shows “1” then press
∧
( ) to desired setting.
Upright Models
Figure 3
To keep the temperature setting
from being accidentally changed, the
control may be locked. This is done by
pressing “Alarm Reset” for 3 seconds.
“L” will then appear on display. To
unlock the control, press “Alarm Reset”
for 3 seconds. For the first second,
“U” will appear, and then the current
temperature will appear.
FREEzER OPTIONAl FEATURES
NOTE:Your freezer may have some, or all of the
features listed below. Become familiar with these fea-
tures, and their use and care.
SECURITY lOCk wITh POP-OUT kEY
This security lock fastens the door snugly, ensuring stored
food is secure. To lock or unlock the freezer, push the key
into the lock and turn. The key pops out of the lock after it
has been turned.
•
Temp Alarm
This feature is designed to provide
a warning if the inside temperature
exceeds 23°F. “HI TEMP” feature
operates on household electricity.
It will not function if household
electricity is interrupted.
SlIDE-OUT BASkET (SOME UPRIGhT MODElS)
Standard Electronic
Temperature Control
Figure 1
A Slide-Out Basket (some models), located at the bottom
of the freezer, provides separate storage space for items
that are difficult to store on freezer shelves. To remove the
basket, pull out and lift up.
•
When the freezer is initially plugged in, the red
“HI TEMP” indicator will be on and the buzzer will
sound. The indicator light will stay on until the freezer
temperature is below 23°F. To silence the buzzer,
press the ALARM RESET button.
INTERIOR lIGhT
The light comes on automatically when the door is opened.
To replace the light bulb, turn the temperature control to
OFF and unplug the electrical cord. Replace the old bulb
with a bulb of the same wattage.
•
If a malfunction causes the temperature inside the
freezer to rise above 23°F, the “HI TEMP” light will turn
on and the buzzer will sound. The buzzer will sound
FI5RST
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTABlE ShElF (SOME UPRIGhT MODElS)
SOFT FREEzE zONE (SOME UPRIGhT MODElS)
This shelf can be moved to one or two positions. Lift the
shelf up and out to move to the desired location.
Soft Freeze Zone is specifically designed to maintain a
higher temperature than the rest of the freezer to store
products such as ice cream.
SlIDE-ASIDE BASkET (SOME ChEST MODElS)
This basket helps organize odd-shaped items. To reach
other packages in the freezer, slide the basket aside, or lift
out.
PIzzA ShElF (SOME UPRIGhT MODElS)
Hereistheplacetostoreuptofourextra-largeboxesoffrozen
pizza without ever having to dig them out from beneath a pile
of other stored goods.
Slide-Aside Basket
FAST FREEzING ShElVES (MANUAl DEFROST
UPRIGhT MODElS)
The pizza shelf can be retracted to provide space for larger
items on the shelf below, and still store up to two more
pizzas.
These shelves contain cooling coils to freeze foods quickly
and allow cold air to constantly circulate throughout the
freezer. Do not use sharp metal objects such as ice picks
or scrapers to clean the shelves. This could damage the
shelves and reduce their cooling ability. These shelves are
not adjustable.
TIlT-OUT ShElF (SOME UPRIGhT MODElS)
This shelf is located inside on the freezer door and pro-
vides additional storage space. To access an item, tilt the
top of the “basket” shelf down.
BASkET DIVIDER (SOME UPRIGhT MODElS)
Use these handy dividers to keep the various items stored
in your baskets more organized. To change the location of
the divider simply slide your basket out, grab the divider
from the center and rotate in a counter-clockwise direction
until it is disengaged. To assemble, simply align as shown
in the figure below and rotate in a clockwise direction until
it spans into place.
Tilt-Out Shelf
ADJUSTABlE DOOR BINS (SOME UPRIGhT MODElS)
Adjustable door bins are located inside on the freezer door
and provide flexible storage space. The number of bins
provided varies by model.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of Chest Divider Configurations:
ShElF BOOkEND (SOME UPRIGhT MODElS)
Glass Shelf Bookend
Use these handy bookends to keep the various boxed
items stored neatly in your freezer. To adjust location,
simply slide where desired.
CARE AND ClEANING
wire Shelf Bookend
Damp objects stick to cold metal
surfaces. Do not touch interior metal
surfaces with wet or damp hands.
CAUTION
Use these handy bookends to keep the various
boxed items stored neatly in your freezer. To adjust
location,simply unsnap the bookend from the wire shelf
and snap into the next desired location.
Freezer must be unplugged (to avoid electrical
hazard) from power source when defrosting unit.
Some upright freezers are frost-free and defrost automati-
cally, but should be cleaned occasionally.
BETwEEN DEFROSTINGS
To avoid frequent defrosting, occasionally use a plastic
scraper to remove frost. Scrape with a pulling motion.
Never use a metal instrument to remove frost.
DEFROSTING
It is important to defrost and clean the freezer when ¼ to
½ inch of frost has accumulated. Frost may tend to accu-
mulate faster on the upper part of the freezer due to warm,
moist air entering the freezer when the door is opened.
Remove food and leave the door open when defrosting the
freezer.
ChEST DIVIDER (SOME ChEST MODElS)
Use these clever dividers to custom-arrange a variety of
different-sizedstoragebinsinthebottomofyourchestfreezer.
Use the peel-n-stick labels found in your literature packet to
help remind you which items are stored where. If you have
an item that isn’t already covered by one of the pre-printed
labels then use one of the blank labels and a permanent
marking pen to make your own custom label. Labels can be
peeled off when no longer needed and replaced by new and
different ones.
To Defrost Upright Models with Defrost Drain:
· Remove the drain plug on the inside floor of the freezer by
pulling it straight out.
· To access external drain tube on models with a base panel,
first remove the two screws from the base panel. Locate
the drain tube near the left center under the freezer.
· Place a shallow pan under the drain tube. Defrost water
will drain out. Check the pan occasionally so water does
not overflow (see figure 1).
· A ½ inch garden hose adapter can be used to drain the
freezerdirectlyintoafloordrain.Ifyourmodelisnotequipped
with an adapter, one can be purchased at most hardware
stores.
· Replace the drain plug when defrosting and cleaning are
completed. If the drain is left open, warm air may enter the
freezer.
FI7RST
Download from Www.Somanuals.com. All Manuals Search And Download.
To Defrost Chest Models
with Defrost Drain:
Do not use razor blades or other sharp instruments, which
can scratch the freezer surface when removing adhesive
labels. Any glue left from the tape can be removed with a
mixture of warm water and mild detergent, or touch the
residue with the sticky side of the tape already removed.
DO NOT REMOVE ThE SERIAl PlATE.
Drain Tube
· Place a shallow pan or
the Divider/Drain Pan (if
equipped) beneath the
drain outlet. Pull out the
outside drain plug (see
figure 2). A ½ inch garden
hose adapter can be used
to drain the freezer directly
intoafloordrain(seefigure
3). If your model is not equipped with an adapter, one can
be purchased at most hardware stores.
· Pull out the drain plug inside the freezer (see figure 4).
Defrost water will drain out. Check pan occasionally so
water does not overflow.
VACATION AND MOVING TIPS
Short Vacations:
Drain Pan
Figure 1
•
Leave the freezer operating during vacations of less
than three weeks.
long Vacations:
If the freezer will not be used for several months:
•
•
•
Remove all food and unplug the power cord.
Clean and dry the interior thoroughly.
Leave the freezer door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
· Replace the drain plugs when defrosting and cleaning are
completed. If the drain is left open, warm air may enter the
freezer.
Moving: When moving the freezer, follow these guidelines
Hose
Adaptor
to prevent damage:
Pan
•
•
•
Disconnect the power cord plug from the wall outlet.
Remove foods, then defrost, and clean the freezer.
Secure all loose items such as base panel, baskets,
and shelves by taping them securely in place to
prevent damage.
Defrost
Drain Plug
Defrost
Drain Plug
•
In the moving vehicle, secure freezer in an upright
position to prevent movement. Also protect outside of
freezer with a blanket, or similar item.
Figure 2
Figure 3
To Defrost Models without
Drain
Defrost Drain:
Plug
If leaving the freezer
door open while on vacation, make
certain that children cannot get into
the freezer and become entrapped.
· Placetowelsornewspapers
on the freezer bottom to
catch the frost.The frost will
loosen and fall.
· Remove the towels and/or
newspapers.
· If the frost is soft, remove it
by using a plastic scraper. If
the frost is glazed and hard,
fill deep pans with hot water
and place them on the freezer bottom.
· Close the freezer door/lid. Frost should soften in about
fifteen (15) minutes.
POwER FAIlURE / FREEzER FAIlURE
NOTE: Do not open freezer door
unnecessarily if freezer is off for
several hours.
Figure 4
If a power failure occurs, frozen foods will stay frozen for
at least 24 hours if the freezer is kept closed. If the power
failure continues, pack seven or eight pounds of dry ice
into the freezer every 24 hours. Look in the Yellow Pages
under Dry Ice, Dairies, or Ice Cream Manufacturers for lo-
cal dry ice suppliers. Always wear gloves and use caution
when handling dry ice.
· Repeat this procedure is necessary.
ClEANING ThE INSIDE
After defrosting, wash inside surfaces of the freezer with
a solution of two tablespoons of baking soda in one quart
(1.1 litres) warm water. Rinse and dry. Wring excess water
out of the sponge or cloth when cleaning in the area of the
controls, or any electrical parts.
If the freezer has stopped operating, see Freezer Does
Not Run in the Troubleshooting Guide. If you cannot
solve the problem, call an authorized servicer immediately.
Wash the removable parts and door basket with the bak-
ing soda solution mentioned above, or mild detergent and
warm water. Rinse and dry. Never use metallic scouring
pads, brushes, abrasive cleaners, or alkaline solutions on
any surface. Do not wash removable parts in a dishwasher.
If the freezer remains off for several hours, follow the direc-
tions above for the use of dry ice during a power failure.
If necessary, take the food to a local locker plant until the
freezer is ready to operate. Look in the Yellow Pages under
Frozen Food Locker Plants.
ClEANING ThE OUTSIDE
Wash the cabinet with warm water and mild liquid de-
tergent. Rinse well and wipe dry with a clean soft cloth.
Replace parts and food.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling for service, review this list. It may save you time and expense. This list
includes common occurences that are not the result of defective workmanship or
materials in this appliance.
TROUBLESHOOTING
GUIDE
PROBLEM
FREEZER DOES NOT RUN
Freezer does not run.
CAUSE
CORRECTION
• Freezer is plugged into a circuit
that has a ground fault interrupt.
• Temperature control is in the
OFF position.
• Use another circuit. If you are unsure about the outlet,
have it checked by a certified technician.
• See Setting the Temperature Control Section.
• Freezer may not be plugged in,
or plug may be loose.
•
Ensure plug is tightly pushed into outlet.
• House fuse blown or tripped
circuit breaker.
• Check/replace fuse with a 15 amp time-delay fuse. Reset
circuit breaker.
• Power outage.
• Check house lights. Call local Electric Company.
• Room or outside weather is hot. • It's normal for the freezer to work harder under these
Freezer runs too much or too
long.
conditions.
• Freezer has recently been
disconnected for a period of
time.
• It takes 4 hours for the freezer to cool down completely.
• Large amounts of warm or hot
food have been stored recently.
• Warm food will cause freezer to run more until the
desired temperature is reached.
• Doors are opened too frequently • Warm air entering the freezer causes it to run more.
or too long.
Open doors less often.
• Freezer door may be slightly
open.
• See "DOOR PROBLEMS" Section.
• Temperature Control is set too
low.
• Turn control knob to a warmer setting. Allow several hours
for the temperature to stabilize.
• Freezer gasket is dirty, worn,
cracked, or poorly fitted.
• Clean or change gasket. Leaks in the door seal will cause
freezer to run longer in order to maintain desired
temperature.
• Temperature Control is set too
low.
• Turn the control to a warmer setting. Allow several hours
for the temperature to stabilize.
Interior Freezer temperature is
too cold.
• Temperature Control is set too
warm.
• Turn control to a colder setting. Allow several hours for the
temperature to stabilize.
Interior Freezer temperature is
too warm.
• Door is kept open too long or is
opened too frequently.
• Door may not be seating
properly.
• Warm air enters the freezer every time the door is
opened. Open the door less often.
• See "DOOR PROBLEMS" Section.
• Large amounts of warm or hot
food may have been stored
recently.
• Wait until the freezer has had a chance to reach its
selected temperature.
• Freezer has recently been
disconnected for a period of
time.
• Freezer requires 4 hours to cool down completely.
• The external freezer walls can
be as much as 30°F warmer
than room temperature.
• This is normal while the compressor works to transfer
heat from inside the freezer cabinet.
Freezer external surface
temperature is warm.
SOUND AND NOISE
• Modern freezers have increased • This is normal. When the surrounding noise level is low,
Louder sound levels whenever
freezer is on.
storage capacity and more
stable temperatures. They
require a high efficiency
compressor.
you might hear the compressor running while it cools the
interior.
• Freezer operates at higher
pressures during the start of the
ON cycle.
• This is normal. Sound will level off or disappear as freezer
continues to run.
Longer sound levels when
compressor comes on.
FI9RST
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
CAUSE
CORRECTION
SOUND AND NOISE (Cont.)
• Metal parts undergo expansion • This is normal. Sound will level off or disappear as
Popping or cracking sound
when compressor comes on.
and contraction, as in hot water
pipes.
freezer continues to run.
• Refrigerant (used to cool
freezer) is circulating
• This is normal.
Bubbling or gurgling sound,
like water boiling.
throughout the system.
• Freezer is not level. It rocks on
the floor when it is moved
slightly.
• Level the unit. Refer to "Leveling" in the First Steps
Section.
Vibrating or rattling noise.
• Floor is uneven or weak.
Freezer rocks on floor when it
is moved slightly.
• Ensure floor can adequately support freezer. Level the
freezer by putting wood or metal shims under part of the
freezer.
• Freezer is touching the wall.
• Relevel the freezer or move freezer slightly. Refer to
"Leveling" in the First Steps Section.
WATER/MOISTURE/FROST INSIDE FREEZER
• Weather is hot and humid,
which increases internal rate of
frost build-up.
• This is normal.
Moisture forms on inside
freezer walls.
• Door may not be seating
properly.
• Door is kept open too long, or
is opened too frequently.
• See "DOOR PROBLEMS" Section.
• Open the door less often.
WATER/MOISTURE/FROST OUTSIDE FREEZER
• Door may not be seating
• See "DOOR PROBLEMS" Section.
Moisture forms on ouside of
freezer.
properly, causing the cold air
from inside the freezer to meet
warm moist air from outside.
ODOR IN FREEZER
Odors in freezer
• Interior needs to be cleaned.
• Foods with strong odors are in
the freezer.
• Clean interior with sponge, warm water, and baking
soda.
• Cover the food tightly.
DOOR PROBLEMS
Door will not close.
• Freezer is not level. It rocks on
the floor when it is moved
slightly.
• This condition can force the cabinet out of square and
misalign the door. Refer to "Leveling" in the First Steps
Section.
• Floor is uneven or weak.
Freezer rocks on floor when it
is moved slightly.
• Level the floor by using wood or metal shims under the
freezer or brace floor supporting the freezer.
LIGHT BULB IS NOT ON
Light bulb is not on.
• Light bulb is burned out.
• Follow directions under "Interior Light" in the Freezer
Features Section.
• No electric current is reaching
• See "FREEZER DOES NOT RUN" Section.
the freezer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
If You Need
Service
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USA
Canada
1.800.944.9044
Electrolux Major Appliances
North America
1.800.668.4606
Electrolux Canada Corp.
5855 Terry Fox Way
P.O. Box 212378
Augusta, GA 30907
Mississauga, Ontario, Canada
L5V 3E4
FI11RST
Download from Www.Somanuals.com. All Manuals Search And Download.
|