Flymo Trimmer 500 XT User Manual

Contour 500 XT  
Original Instructions  
For all customer enquiries or for replacement parts, contact:-  
¤ 01325 300303  
customer.services@husqvarna.co.uk  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Do not pull cable around sharp objects.  
8. Always switch off at the mains before disconnecting  
any plug, cable connector or extension cable.  
9. Never pull on the cable to disconnect any of the plugs.  
10.Switch off, remove plug from mains and examine electric  
supply cable for damage or ageing before winding cable  
for storage. Do not repair a damaged cable, replace it with  
a new one. Use only Flymo replacement cable.  
11.Always wind cable carefully, avoiding kinking.  
12.Never carry the product by the cable.  
13.Use only on AC mains supply voltage shown on the  
product rating label.  
other than grass.  
8. Never operate the trimmer with damaged guards or  
without guards in place.  
9. Never fit metal cutting elements.  
10.Keep hands and feet away from the cutting means at  
all times and especially when switching on the motor.  
11.Never pick up or carry a trimmer by the cable.  
12.Do not lean over the trimmer guard - objects may be  
thrown by the cutting line.  
13.Beware of cut-off pieces of nylon line ejected during use.  
14.Remove the plug from the mains :  
-
-
-
-
before leaving the trimmer unattended for any period;  
before clearing a blockage;  
14.Our products are double insulated to EN60335.  
Under no circumstance should an earth be con-  
nected to any part of the trimmer.  
before checking, cleaning or working on the appliance;  
if you hit an object. Do not use your trimmer until you are  
sure that the entire trimmer is in a safe operating condition;  
if the trimmer starts to vibrate abnormally. Check im-  
mediately. Excessive vibration can cause injury.  
Preparation  
1. While using your product always wear substantial  
-
footwear and long trousers.  
Maintenance and storage  
2. Before using the machine and after any impact, check  
for signs of wear or damage and repair as necessary.  
3. Inspect the area to be cut before each use. Remove all objects  
such as stones, broken glass, nails, wire, string etc, which can  
be thrown or become entangled in the trimmer head.  
4. Before use, inspect the area for wildlife, especially hedge-  
hogs.  
1. Keep all nuts, bolts and screws tight to be sure the  
trimmer is in safe working condition.  
2. Replace worn or damaged parts for safety.  
3. Only use the replacement cutting line specified for  
this product.  
4. Only use replacement parts and accessories recom-  
mended by Husqvarna UK Ltd.  
5. Check that the cutting head is fitted correctly.  
Use  
5. After any maintenance in dealing with the cutting line,  
always return the product to its normal operating posi-  
tion before switching on.  
1. Use the trimmer only in daylight or good artificial light.  
2. Avoid operating your trimmer in wet grass, where feasible.  
3. Take care in wet grass, you may lose your footing.  
4. On slopes, be extra careful of your footing and wear  
non-slip footwear.  
6. Clean unit with a dry cloth. Never use metal objects  
to clean the unit.  
7. Inspect and maintain the trimmer regularly. Any repairs  
must be carried out by an authorised repairer.  
8. Store in a cool dry place and out of reach of children.  
Do not store outdoors.  
5. Do not walk backwards when trimming, you could  
trip. Walk never run.  
6. Keep cutting head below waist level.  
7. Switch off before pushing the trimmer over surfaces  
Cables  
IMPORTANT  
off plug is inserted into a 13 amp socket.  
1.No earth required. Flymo products are double insulated  
to EN60335 and under no circumstances should an earth  
be connected to any part of the product.  
2
Use only 1.00mm size cable up to 40 metres length maxi-  
mum.  
Maximum rating:  
2
1.00mm size cable, 10 amps 250 volts AC.  
2.Ensure the mains voltage suits your product.  
3.IMPORTANT!  
YOUR PRODUCT IS SUPPLIED WITH AN ELECTRIC  
MAINS CABLE WIRED DIRECTLY INTO THE PRODUCT.  
1.Flymo Mains Cables and Extension Cables are avail-  
able from your local Approved Service Centre.  
2.Do not wire an extension cable directly to your product your-  
self. Please contact your local Approved Service Centre for  
further information on the connectors and kits available.  
3.Only use extension cables specifically designed for  
outdoor use.  
The wires in the mains lead are coloured in accordance  
with the following code:  
BLUE -  
NEUTRAL  
BROWN  
-
LIVE  
The wire which is coloured BLUE must be connected to the  
Terminal which is marked with the letter ʻNʼ or coloured BLACK.  
The wire which is coloured BROWN must be connected to the  
Terminal which is marked with the letter ʻLʼ or coloured RED.  
4.It is important that the outer sheath is clamped cor-  
rectly into the 3-pin plug.  
CONNECTORS  
5.If in doubt consult your local Service Repairer or quali-  
fied electrician before the machine is used.  
Flymo connectors are suitable for use with 2 core cable  
only. Under no circumstances should these connectors  
be used for earthed products.  
6.A 5 Amp fuse must be fitted to the Mains Plug.  
7.The normal plug fuse and household fuse only protect  
the electrical equipment and are not a safeguard  
against electrocution.  
All Flymo connectors and cables are of splashproof con-  
struction. They are not waterproof and must not be left out-  
side permanently nor should they be submerged or  
immersed in water. Do not let cable lay or trail through  
pools of water or splashed with water from hose pipes.  
MAINS PLUG REPLACEMENT  
If your product is hard wired i.e. non-detachable  
mains electric cable, a conversion kit and extension  
cable is available from all Approved Service Centres  
which can be found in your local Yellow Pages.  
• If the plug supplied is cut off it should be de-  
stroyed. There is an electric shock hazard if a cut  
Assembly Instructions  
Assembly of Switch Handle to Tube (A1)  
Ensure that the internal cable is not twisted.  
A1  
A2  
1. Insert the tube into the switch handle.  
2. Push until it clicks into position.  
ENSURE THAT THE TUBE IS FULLY LOCATED BY  
ATTEMPTING TO REMOVE IT.  
Assembly of Trimmer Head to Tube (A2)  
Ensure that the internal cable is not twisted.  
1. Insert the tube into the trimmer head.  
2. Push until it clicks into position.  
ENSURE THAT THE TUBE IS FULLY LOCATED BY  
ATTEMPTING TO REMOVE IT.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly Instructions cont’  
B1  
B2  
C2  
Wheel Assembly (B1) & (B2)  
1. Fix the 2 halves of the wheel together as illustrated in  
fig B1.  
2. Attach the wheel to the trimmer making sure that it is  
located into the groove on the trimmer head (B2).  
3. Clip the wheel together on the other side, making sure  
it is secure.  
4. The wheel should turn freely.  
Safety Guard Assembly (C1) & (C2)  
C1  
1. Locate the safety guard over the cutting head. Ensure  
the nylon line is fed through the hole in the safety  
guard as illustrated in fig C1.  
2. Push into location and turn safety guard in the direc-  
tion illustrated in Fig C2, until a click is heard and the  
safety guard is securely locked in position.  
ENSURE THE SAFETY GUARD IS SECURELY IN  
PLACE BY ATTEMPTING TO TWIST GUARD.  
Steady Handle Assembly (D)  
1. Depress the two buttons on the sides of the switch  
D
E
handle.  
2. Locate the steady handle over the buttons and release  
the buttons.  
1
3. Adjust the steady handle to the most comfortable oper-  
ating position by depressing the buttons and moving  
the handle.  
1
2
3
Height Adjustment (E)  
1. Turn height adjuster (E1) in the direction indicated to  
2
un-lock (E2).  
2. Adjust the length of the tube to the most comfortable  
operating position.  
F1  
F2  
3. Turn height adjuster in the opposite direction to lock  
(E3).  
ENSURE THAT THE TUBE IS FULLY SECURED.  
Cable Restraint (F1) & (F2) (optional)  
1. Form loop in mains cable and push the loop through  
the slot as illustrated in picture (F1).  
2. To secure, position loop over the hook and pull the  
cable back through the slot as illustrated in picture  
(F2).  
Double Auto Feed System  
How the automatic line feed works (G)  
1. When initially switching on the trimmer, a small length  
G
of line is fed out.  
2. A ʻclatteringʼ noise will be heard when the two nylon  
lines hit the line cutter. DO NOT BE ALARMED this  
is quite normal. After approximately 5 seconds the  
line will be cut to the correct length and the noise will  
reduce as the motor reaches full speed.  
Make sure the motor is up to full speed before  
trimming or edging.  
3. If the noise of the nylon line being cut cannot be heard,  
more line will need to be fed out.  
4. To feed more line, it is first necessary to to allow the  
motor to stop completely, then re-start, allowing the  
motor to reach full speed.  
line cutter  
5. Repeat step 4. until you hear the lines hitting against the  
cutter. (Do not repeat this procedure more than 6 times)  
6. If problems are experienced with the automatic line  
feed refer to Fault Finding Chart.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use  
WARNING  
H
J1  
The use of eye protection is recommended.  
Do not lean over the trimmer whilst trimming or  
edging, objects may be thrown by the cutting line.  
Do not allow cutting head to rest on the ground.  
Do not overload your trimmer.  
Overloading can be avoided by making sure the  
motor speed does not drop unduly.  
DISCONNECT FROM THE MAINS ELECTRICITY  
SUPPLY BEFORE ATTEMPTING ANY MAINTE-  
NANCE OR ADJUSTMENT.  
BEFORE USE  
Make sure that both lines are fed out.  
Make sure motor is up to full speed before trim-  
ming or edging.  
J2  
How to trim  
1. Hold as illustrated in Fig H.  
2. To start, squeeze the switch lever.  
3. Cut with nylon line at an angle using the tip. See Fig  
J1.  
4. Swing trimmer in and out of the cutting area taking  
small cuts (J2)  
5. Line is fed out automatically every time the trimmer  
head stops rotating and returns to operating speed.  
K2  
K1  
Extra line can be fed out manually as described in  
Manual line feed  
6. To stop your trimmer release the switch lever.  
Using the Plant & Tree Guard  
The Plant and Tree Guard (K1) allows the trimming of  
grass close to plants and trees without damaging  
them with the cutting line.  
1. Flip the guard down as illustrated in Fig K1.  
2. Use the trimmer around trees (K2) and near plants.  
L
3
2
1
How to edge  
1. To convert to edging mode, press button (L1) and twist  
head (L2). An audible "click" will confirm that the head  
is locked. Ensure the Plant and Tree Guard is flipped  
upwards (L3)  
2. Hold as illustrated in Fig H.  
3. To start, squeeze the switch lever.  
4. Rest edger on wheel for extra stability and line up the  
edge of the lawn with the two indicators on the guard  
(M1). Edge in direction indicated in Fig M.  
5. To stop your trimmer release the switch lever.  
6. To return to trimming mode, press button and twist  
head back the opposite way. An audible "click" will  
confirm that the head is locked.  
M
Using the Shrubbing position  
1
1. By pressing the lever (N1) with your foot, the handle  
can be lowered into three different positions to enable  
the use of the product under shrubs and low obstacles  
(P).  
N
P
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual line feed  
Q
To manually feed the nylon line (Q)  
1. If required line can be fed out manually.  
2. To operate, press and release manual line feed button,  
whilst gently pulling on one of the lines until the line  
reaches the line cutter.  
3. When the required amount of line is fed out, gently pull  
on the second line (there is no need to press the man-  
ual line feed button again).  
4. If the line extends past the line cutter, too much line  
has been fed out.  
manual line  
feed button  
5. If too much line is fed out, remove the spool cap and click  
spool anti-clockwise until the line is at the desired length.  
Always return the product to its normal operating po-  
sition before switching on.  
Cutting Head  
R
To remove spool cap  
1. Press and hold in the two cap release latches. (R).  
2. Pull cap away from the spoolholder. (R).  
When refitting the spool cap  
Cap  
1. Keep all areas of the cap and spoolholder clean.  
Failure to do so may prevent the cap being securely  
located in the spoolholder.  
Cap release  
latch  
Spool  
2. Replace the cap, pressing firmly DOWN towards  
the spoolholder to ensure cap is fully located.  
3. Check that the cap is correctly fitted by trying to re-  
move it without depressing the two latches.  
To replace nylon line.  
Spoolholder  
For your convenience it is recommended you buy spool  
and line complete. Nylon line only is also available. Both  
are available from Husqvarna UK Ltd. stockists.  
To fit spool and line complete:  
Slot  
1. Remove the cap.  
S
S1  
2. Remove old spool.  
3. Place spool into spoolholder.  
4. Release one line from cleat (T1).  
5. Secure line into slot (S1).  
6. Repeat for second line.  
Ensure spool is fully located by gently rotating it during  
fitment, whilst keeping the spoolholder steady.  
7. Refit the cap.  
To fit nylon line only:  
Remember! Your Flymo Trimmer is designed to use  
only nylon line with a maximum diameter of 1.5mm.  
Use only genuine Flymo nylon line.  
T1  
Cleat  
1. IMPORTANT - Always wind the line onto the upper  
section of the spool first.  
Take approximately 5 metres of line. Insert 15mm of  
line into one of the holes in the upper section of the  
spool (T) and wind line in the direction of the arrows  
on the top of the spool. Leave approximately 100mm  
of line unwound and place into cleat as illustrated in  
figure T1. Repeat on lower section of spool.  
2. Care should be taken to ensure that the line is neatly  
coiled on the spool. Failure to do so will impair the ef-  
ficiency of the automatic line feed.  
T
3. Then fit spool as described in To fit spool and line  
complete’, section above.  
Always return the product to its normal operating po-  
sition before switching on.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
V
WARNING  
Disconnect from the mains electricity supply, be-  
fore attempting any maintenance or adjustment.  
Cutting head continues to rotate after the trimmer  
has been switched off. Keep fingers and hands  
clear of the line cutter on leading edge of guard.  
W
X
Caring for your product  
After you have finished using your product follow the pro-  
cedure below:  
AVOID ACCIDENTAL STARTING. REMOVE PLUG  
FROM MAINS AND KEEP FEET AWAY FROM THE  
SWITCH LEVER WHEN: CLEANING AROUND THE IN-  
SIDE OF THE SAFETY GUARD, REMOVING OR RE-  
FITTING SPOOL CAP, MANUALLY FEEDING OR  
REPLACING NYLON LINE.  
1. Disconnect from the mains electricity supply.  
2. Never clean your trimmer with water, cleaning fluids,  
or solvents, just remove debris with a suitable tool, a  
soft brush or dry cloth.  
3. Using a soft brush, clean around the inside of the  
safety guard, the cutting head (V) and the motor  
housing air vents. (W  
4. Remove the wheel by pressing one of the buttons.  
Clean the wheel and groove on trimmer head with a  
soft brush (X & Y).  
5. Attach wheel as described in Wheel Assembly.  
6. Inspect the trimmer carefully, especially the parts of  
the cutting head.  
Z1  
Y
7. If your trimmer is damaged in any way contact your  
local approved service centre.  
Never use a damaged trimmer.  
8. Store in a cool, dry place and out of reach of children.  
Cable Storage  
1. Your mains cable can be stored on the product as il-  
lustrated in Fig Z1.  
2. Wind cable carefully to avoid kinking.  
3. To release the cable press the button and the hook  
will drop down (Z2).  
Z2  
4. Push cable hook fully back into position.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fault Finding Chart  
WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.  
FAULT  
CHECK  
ACTION  
Is the automatic line feed work-  
ing?  
Is the line fed out and visible?  
Has line been removed from  
cleat?  
Manually feed out line.  
LINE NOT FEEDING  
OR  
LINE TOO SHORT  
OR  
No  
No  
SEE MANUAL LINE FEED”  
Remove cap and spool, free line  
and re-fit spool and cap. SEE  
CUTTING HEAD”  
TRIMMER VIBRATES  
The line may be jammed on the  
spool. Rewind line to remove  
crossed loops. Check that line is in  
correct section of spool.  
Is the manual line feed working?  
No  
Has the motor reached full  
speed before use?  
Allow the motor to reach full speed  
No  
before use.  
CONTINUOUS CLATTER-  
ING NOISE  
Has too much line been fed out?  
SEE MANUAL LINE FEED”  
Yes  
Contact your local approved  
Service Centre or Husqvarna UK  
Ltd. Customer Service.  
Is the line cutter missing from the  
safety guard?  
Yes  
?
Are you using the trimmer cor-  
rectly?  
Only use tip of nylon line to trim.  
LINE SNAPS CONTINU-  
OUSLY  
SEE How to trim and edge”  
Rewind the line on the spool, if  
Is the line jamming on the spool? Yes symptoms still persist, change  
spool and line.  
Clean wheel and groove on trimmer head. SEE MAINTENANCE”  
WHEEL STOPS TURNING  
IF NONE OF THE ABOVE  
OR IF FAULT PERSISTS  
Contact Husqvarna UK Ltd. Customer Service  
Telephone : 01325 300303  
Guarantee & Guarantee Policy  
If any part is found to be defective due to faulty manufacture  
within the guarantee period, Husqvarna UK Ltd., through its Au-  
thorised Service Repairers will effect the repair or replacement to  
the customer free of charge providing:  
ual and understand how to operate and maintain your machine:  
Failures not covered by guarantee  
* Replacing Nylon Line.  
* Failures as a result of not reporting an initial fault.  
* Failures as a result of sudden impact.  
(a) The fault is reported directly to the Authorised Repairer.  
(b) Proof of purchase is provided.  
* Failures as a result of not using the product in accordance with the in-  
structions and recommendations contained in this Operator's Manual.  
* Machines used for hire are not covered by this guarantee.  
* The following items listed are considered as wearing parts and  
their life is dependent on regular maintenance and are, there-  
fore not normally subject to a valid warranty claim: Nylon Line,  
Spool and Line, Electric Mains Cable  
(c) The fault is not caused by misuse, neglect or faulty adjustment  
by the user.  
(d) The failure has not occurred through fair wear and tear.  
(e) The machine has not been serviced or repaired, taken apart or tam-  
pered with by any person not authorised by Husqvarna UK Ltd..  
(f) The machine has not been used for hire.  
(g) The machine is owned by the original purchaser.  
(h) The machine has not been used commercially.  
* Caution!  
Husqvarna UK Ltd. does not accept liability under the warranty  
for defects caused in whole or part, directly or indirectly by the  
fitting of replacement parts or additional parts that are not either  
manufactured or approved by Husqvarna UK Ltd., or by the ma-  
chine having been modified in any way.  
*
This guarantee is additional to, and in no way diminishes the  
customers statutory rights.  
Failures due to the following are not covered, therefore it is impor-  
tant that you read the instructions contained in this Operator's Man-  
Environmental Information  
• Awareness of the environment must be considered  
when disposing of ʻend-of-lifeʼ product.  
• If necessary, contact your local authority for disposal  
information.  
for the recycling of electrical and electronic equipment. By en-  
suring this product is disposed of correctly, you will help prevent  
potential negative consequences for the environment and  
human health, which could otherwise be caused by inappropri-  
ate waste handling of this product.  
The symbol  
on the product or on its packaging indicates  
For more detailed information about recycling of this product,  
please contact your local council office, your household waste  
disposal service or the shop where you purchased the product.  
that this product may not be treated as household waste. In-  
stead it shall be handed over to the applicable collection point  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EC Declaration of Conformity  
Husqvarna UK Ltd., Aycliffe Industrial Park  
Newton Aycliffe, Co. Durham, DL5 6UP, England  
Declare under our sole responsibility that the product(s);  
Category............................Electric Lawn Trimmer  
Type(s) ............................CTXT25  
Identification of Series.......See Product Rating Label  
Year of Construction..........See Product Rating Label  
Conforms to the essential requirements & provisions of the following EC Directives:  
98/37/EC (until 31.12.09), 2006/42/EC (from 01.01.10), 2004/108/EC, 2000/14/EC  
based on the following EU harmonized standards applied:  
EN60335-1, EN60335-2-91, EN786, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3  
The maximum A weighted sound pressure level LpA at the operatorʼs position, recorded on a sample of the above  
product(s) corresponds to the Level given in the table.  
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above  
product(s) corresponds to the Value given in the table.  
2000/14/EC: The Measured Sound Power LWA & Guaranteed Sound Power LWA values are according to the tabulated figures.  
Conformity Assessment Procedure............... Annex VI  
Notified Body................................................. Intertek, Cleeve Road  
Leatherhead, Surrey  
KT22 7SB, England  
Newton Aycliffe 01/07/2008  
M.Bowden  
Research & Development Director  
Husqvarna UK Ltd.  
Type  
CTXT25  
25  
Width of Cut (cm)  
10,500  
Speed of Rotation of Cutting Device (rpm)  
Power (W)  
500  
91  
Measured Sound Power LWA (dB(A))  
Guaranteed Sound Power LWA (dB(A))  
96  
79  
2.91  
3.26  
Level (dB(A))  
2
Value (m/s )  
Weight (Kg)  
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.  
Husqvarna UK Ltd.  
Aycliffe Industrial Park  
NEWTON AYCLIFFE  
Co.Durham DL5 6UP  
ENGLAND  
Telephone - (00) 44 1325 302302 Fax - (00) 44 1325 310339  
5101570-01  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edimax Technology Network Card LAN USB Adapter User Manual
Eiki Projection Television LC NB2 User Manual
Estate Clothes Dryer EGD4100S User Manual
Euro Pro Iron EP171 User Manual
Excalibur electronic Games TV30 User Manual
FOCUS Enhancements Camcorder FS 3 User Manual
Frigidaire Microwave Oven 316495055 User Manual
GBC Paper Shredder GDHS7 User Manual
GE Iron 169173 User Manual
GE Microwave Oven 164 D2092P021 User Manual